Professional Documents
Culture Documents
info
The free encyclopedia for UK steel construction information
Although many previous national standards, including BS 5950[1], were withdrawn by BSI in 2010 they can still be
used. This is likely to remain the case for some time.
This article introduces the Eurocode system, sets out the format that is used and explains the relationship between the
Eurocodes, their National Annexes and non-contradictory complementary information (NCCI ). It explains that the
basis of structural design is set out in BS EN 1990 [2] and that this defines the common principles and specifies how
design values are to be determined and verified. A brief summary of the various actions (loading) that are defined in
EN 1991 is given.
The article introduces the parts of EN 1993 (Eurocode 3) that are required when designing a steel framed building and
briefly introduces EN 1994 (Eurocode 4), for composite steel and concrete structures, and EN 1992 (Eurocode 2),
which covers the design of the concrete elements in composite structures.
Key issues from the relevant Eurocodes are identified. Much more detail is available in a wide range of guides .
Building Regulations
The Governments of the UK and its devolved regions publish documents which provide guidance on the means by
which compliance with the Building Regulations in force in that region can be achieved. For structure safety these are:
Approved Document A[3] (England); Approved Document A[4] (Wales); Scottish Technical Handbook [5] and Technical
Booklet D[6] in Northern Ireland. It should be noted that the English and Welsh Approved Documents have been
separate only since 2013. Differences between them are small but one should be aware that they exist. When this
article, or any other article on this site, refers to Approved Document A, by default it will be the English version[3].
Approved Document A[3] to the Building Regulations (England) currently references the Eurocodes. It states that:
British Standards for structural design based on the Eurocodes were.....implemented by the British Standards
Institution on 1st April 2010 and it is these standards with their corresponding UK National Annexes which are now
referenced in this Approved Document as practical guidance on meeting Part A requirements.
It further states that: There may be alternative ways of achieving compliance with the requirements and there may be
cases where it can be demonstrated that the use of withdrawn standards no longer maintained by the British
Standards Institution continues to meet Part A requirements.
1 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
It is important to recognise that the regulatory system in the UK is such that the Building Regulations themselves
merely make high level demands, for example that a structure is safe. Use of the standards cited in Approved
Document A[3] is only one way to demonstrate that requirement has been met.
Introduction to Eurocodes
CEN documents
Each Eurocode comprises a number of 'Parts', which are published as separate documents. Each Part consists of a
main body of text, normative annexes, and informative annexes (the 'relevance' of which is decided on a national
basis).
The full text of each Eurocode Part is issued initially by CEN (European Committee for Standardisation) in three
languages with the above 'EN' designations; national standards bodies may translate the text into other languages but
may not make any technical changes. The information given in this text is thus the same for each country in Europe.
2 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The Eurocode text is then provided with a front cover and foreword by each national standards body and published
within that country using a designation with the national prefix - for example EN 1990 is published by BSI as
BS EN 1990 [2]. The text may be followed by a National Annex or a National Annex may be published separately.
The Eurocode Parts contain two distinct types of statement - 'Principles' and 'Application Rules'. The former must be
followed, to achieve compliance; the latter are rules that will achieve compliance with the Principles but it is
permissible to use alternative design rules, provided that they accord with the Principles (see BS EN 1990 [2] 1.4(5)).
The general principle that was adopted in drafting the Eurocodes was that there would be no duplication of Principles
or Application Rules. Thus the design basis in BS EN 1990 [2] applies irrespective of the construction material or the
type of structure.
UK designers should be aware that the Eurocodes use terminology and notation that will be unfamiliar, resulting from
the ambition to achieve consistency across Europe.
National Annexes
The National Annex (NA) is an essential document when using a Eurocode Part . Where the opportunity is given in the
text of the Eurocode, the National Annex will:
Although the NA may specify the value of partial factors to be applied to actions and resistances, in many cases it
simply accepts the value recommended in the Eurocode text.
The guidance given in a National Annex applies to structures that are to be constructed within that country. National
Annexes are likely to differ between countries within Europe. The National Annexes for the country where the structure
is to be constructed should always be consulted in the design of a structure.
3 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
Typical cover page of a Eurocode part Typical cover page of a National Annex
to a Eurocode part
Permission to reproduce extracts from British Standards is granted by the British Standards Institution (BSI). No other use of this material is permitted. British Standards can be
obtained in PDF or hard copy formats from the BSI online shop: http://shop.bsigroup.com or by contacting BSI Customer Services for hard copies only: Tel: +44 (0)20 8996
9001, Email: cservices@bsigroup.com
NCCI
The National Annex may give references to publications that contain non-contradictory complementary information
(NCCI) that will assist the designer when designing a structure to the Eurocodes. According to CEN rules, a National
Annex cannot contain NCCI, but references to NCCI may be given. As the name suggests, any guidance that is
referenced in the National Annex must not contradict the principles of the Eurocode.
The Eurocodes omit some design guidance where it is considered to be readily available in text books or other
established sources. Publications that contain such design guidance may be referenced in the National Annex as
NCCI.
To assist designers, the steel construction sector has collated a large amount of the NCCI required for steel design
and made it available on a readily searchable website www.steel-ncci.co.uk.
Additionally, BSI is publishing NCCI guidance in the form of several 'Published Documents' (PDs), e.g. PD
6695-1-10[31]. These documents are only informative and do not have the status of a Standard.
Requirements
Principles of limit state design
Basic variables
Structural analysis and design assisted by testing
Verification by the partial safety factor method.
The principles of limit state design (LSD) are set out briefly and the relevant design situations are classified as:
4 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
Ultimate and serviceability limit states are defined and the requirement that verifications (checks) shall be carried out
is stated.
BS EN 1990 [2] gives expressions for the effects for three classes of combination of actions at the ultimate limit state:
For fundamental combinations, BS EN 1990 [2] gives two alternative methods to determine the design value of the
effects of combined actions.
The second method is to give two expressions for the combination of actions; the combination that gives the most
onerous value should be used for the design verifications:
where:
Gk,j represents the characteristic value of the j-th unfavourable permanent action
P is a prestressing action
Qk,1 is the characteristic value of leading variable action ('main accompanying action' in 6.10a)
Qk,i represents the characteristic value of the i-th accompanying variable action (i > 1)
5 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
G, P, Q are representations of the factor F according to the type of action to which they relate
For the majority of steel elements, the above expressions will simplify, as prestressing actions (P) will not be present.
Typical values, from the UK National Annex, are given in the tables below.
Design values of actions (STR) taken from Table NA.A1.2(B) of the UK National Annex to BS EN 1990
Values of factors for buildings, extracted from Table NA.A1.1 of the UK National Annex to BS EN 1990
Action 0
The National Annex[32] must be consulted for guidance on which method to use. In the UK, the National Annex[32]
allows either approach to be used. However, in almost all persistent design situations the use of the second method
(the use of expressions 6.10a and 6.10b) will produce lower design values of the effects of actions (and for buildings,
6.10b usually gives the governing value). For the transient design situation during execution, 6.10a is effectively the
same as 6.10 (since = 1.0 - see BS EN 1991-1-6 [16] clauses A.1.1 and NA 2.18) and thus governs rather than
6.10b.
6 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
For building design, Annex A of BS EN 1990 [2] gives recommended values of the factors , and ; for buildings in the
UK, the values are given in the National Annex to BS EN 1990 [32] , clause NA.2.2.
Quasi permanent combination Reversible limit states and long term effects
The expression for the Characteristic combination of actions given in BS EN 1990 [2] for serviceability limit state design
is shown below.
The Frequent and Quasi-permanent combinations are not relevant to steel design in the UK.
The serviceability limits for vertical and horizontal deflections and dynamic effects may be given in the relevant
material Eurocode. The UK National Annex to BS EN 1993-1-1[21] gives suggested limits for vertical (see table below)
and horizontal deflections due to variable actions only, stating that deflections due to permanent actions need not be
verified. With agreement from the Client, different limits may be used for a specific project.
Cantilevers Length/180
Eurocode 1 - Actions
This section relates to BS EN 1991 Part 1 for buildings only. Alternative actions should be considered for the design of
bridges .
7 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
BS EN 1991-1-1[7] gives design guidance and values of actions to be used when designing buildings and civil
engineering works. It contains guidance on:
The accompanying UK National Annex[8] presents tables containing significantly more occupancy sub-groups than
given in the main text of the Eurocode. Some typical values are given in the tables below. The UK National Annex[8]
also replaces the expression given for the reduction factor for imposed floor loads and accessible roofs (A) and the
reduction factor for imposed loads from several storeys (n).
Minimum imposed load for office areas, from Table NA.2 and NA.3 of the National Annex to BS EN 1991-1-1
8 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The methods given in BS EN 1991-1-2[9] should be used to determine the thermal and mechanical actions that act on
structures exposed to fire. The values of actions determined should be used when carrying out fire engineering design
to Part 1-2 of the relevant material Eurocode. The values of actions determined are considered to be accidental
actions.
The UK NA[10] gives guidance for temperature analysis and fire models.
For the period of time within which to make the temperature analysis the UK NA[10] refers the designer to the:
The UK National Annex[10] specifies that no additional actions need be considered as acting simultaneously with the
fire load and that the representative value of the variable action Q1 should be taken as the frequent value (1,1, Q1).
Snow loads
BS EN 1991-1-3[11] gives roof snow load coefficients that are to be used with the characteristic ground snow load
maps given in Annex C of that Part of BS EN 1991 to determine design roof snow loads for different roof shapes. The
UK National Annex[12] replaces the ground snow load map and some of the roof coefficients for buildings to be
constructed in the UK.
Wind actions
The guidance given in BS EN 1991-1-4[13] should be used to determine the wind actions to be considered during the
structural design of buildings and civil engineering works. The information given is applicable to the whole or part of a
structure, including elements attached to it such as cladding. The values of wind actions are derived from a
fundamental value of the basic wind velocity (which is given in the appropriate National Annex), from which a mean
wind speed and peak velocity pressure are determined for the particular building; wind pressures and forces are
determined using coefficients given in BS EN 1991-1-4[13]. The UK National Annex[14] provides numerous tables and
figures for determining values for buildings in the UK.
Guidance to assist structural engineers with the evaluation of wind actions for buildings in the UK is available in SCI-
P394, and a Wind loading calculator is also available.
Thermal actions
Where structures are exposed to daily and seasonal climatic changes in temperature, the effects of thermal actions
should be accounted for in the design. BS EN 1991-1-5[15] gives principles and general rules that should be used to
determine the characteristic values of thermal actions.
The values of actions which should be taken into account during the construction of a building or civil engineering
works should be obtained from the principles and general rules given in BS EN 1991-1-6[16].
9 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The SCI advisory desk note AD346 gives guidance for determining the value of the actions present during the
execution of a steel and concrete composite floor.
Accidental actions
Strategies and rules for safeguarding buildings and other civil engineering works against accidental actions are given
in BS EN 1991-1-7 [17]. There are no rules for determining specific values of accidental actions caused by external
explosions, warfare or terrorist activities, or for verifying the residual stability of structures damaged by seismic action
or fire, etc.
Information regarding limiting the effects of a localised failure in buildings from an unspecified cause is given in
Annex A of BS EN 1991-1-7 [17]. The effects are limited in order to avoid disproportionate collapse of the structure.
Annex A includes information relating to:
For steel and concrete composite structures, Eurocode 3 is referred to by Eurocode 4 [34] for the design of the steel
elements.
10 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
SCI has produced a series of guides covering the application of Eurocode 3, as well as an Introduction (SCI P361)
and a Concise Guide (SCI P362). These cover all the essential rules for steel building design in accordance with the
UK National Annexes.
BS EN 1993-1-1 [20] gives generic design rules for steel structures and specific guidance for structural steelwork used
in buildings. The main aspects in BS EN 1993-1-1 [20] are:
Material properties
Structural analysis
Section classification
Section and member resistances.
Material properties
The rules in BS EN 1993-1-1 [20] relate to structural steel grades S235 to S460 in accordance with BS EN 10025 [35],
BS EN 10210 [36] or BS EN 10219 [37] and thus cover all the structural steels likely to be used in buildings. In
exceptional circumstances, components might use higher strength grades; BS EN 1993-1-12 [27] gives guidance on the
use of higher strength steels. For the design of stainless steel components and structures, reference should be made
to BS EN 1993-1-4 [23].
The UK National Annex[21] states that the nominal yield strength (fy) and ultimate strength (fu) of steel should be
obtained from the minimum specified values according to the product standards.
Structural analysis
Section 5.2 of BS EN 1993-1-1 [20] gives guidance on global analysis of structures and the structural stability of
frames.
Generally, first order elastic global analysis may be used. In some circumstances (depending on member
classification) plastic global analysis may be used. Where the internal moments and forces are significantly increased
due to deflections, second order effects need to be taken into account, either through magnification of first order
effects or by a second order analysis.
Section classification
11 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
Four classes of cross section are defined in BS EN 1993-1-1 [20] . Each part of a section that is in compression is
classified and the class of the whole cross section is deemed to be the highest (least favourable) class of its
compression parts.
Class 1 cross-sections are those which can form a plastic hinge with the rotation capacity required from plastic
analysis without reduction of the resistance
Class 2 cross-sections are those which can develop their plastic moment resistance, but have limited rotation
capacity because of local buckling
Class 3 cross-sections are those in which the stress in the extreme compression fibre of the steel member
assuming an elastic distribution of stresses can reach the yield strength, but local buckling is liable to prevent
development of the plastic moment resistance
Class 4 cross-sections are those in which local buckling will occur before the attainment of yield stress in one
or more parts of the cross-section.
Table 5.2 of BS EN 1993-1-1 [20] gives limits for the width to thickness ratios for the compression parts of a section for
each classification.
Expressions for determining the cross section resistance in tension, compression, bending and shear for the four
classes of sections are given in Section 6.2 of BS EN 1993-1-1 [20] . The design values of resistance are expressed as
Nt,Rd, Nc,Rd, Vc,Rd and Mc,Rd respectively.
12 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
For slender webs, the shear resistance may be limited by shear buckling; for such situations, reference is made to
BS EN 1993-1-5 [24] Shear buckling is rarely a consideration with hot rolled sections.
The buckling resistance of a member is determined by applying a reduction factor to the yield strength. The value of
varies depending on the buckling mode, with an appropriate subscript identifying which mode is being considered -
for example LT is the reduction factor for lateral torsional buckling.
Members in compression
BS EN 1993-1-1 [20] presents guidance for checking flexural, torsional and torsional-flexural buckling for members in
compression. The latter two modes will not be critical for doubly symmetric I or H sections, or hollow sections.
Members in bending
Laterally unrestrained members in bending about their major axes need to be verified against lateral torsional buckling.
Rules are given in Clause 6.3.2 of BS EN 1993-1-1 [20].
13 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The guidance given for calculating the beam slenderness for the first two approaches requires the value of the elastic
critical moment for lateral torsional buckling (Mcr), but no expressions are given for determining this value. An NCCI
method for calculating beam slenderness for rolled I, H and channel sections is given in SCI P362. NCCI (SN003b EN
EU) for calculating Mcr is also available.
The third method treats the compression flange and part of the web as a simple compression member.
For members subject to bending and axial compression, the criteria given in 6.3.3 of BS EN 1993-1-1 [20] must be
satisfied.
Interaction factors (kij) used in the verifications may be calculated using either method 1 or 2 given respectively in
Annexes A or B of BS EN 1993-1-1 [20]. Method 2 is considered to be the simpler of the two methods.
The general method given in 6.3.4 of BS EN 1993-1-1 [20] should not be confused with the general case for lateral
torsional buckling given in 6.3.2.2 of EN 1993-1-1[20]. The general method gives guidance for structural components
that are not covered by the guidance given for compression, bending or bending and axial compression members, and
is not likely to be used by most building designers.
BS EN 1993-1-1 [20] does not give any serviceability limit state limits for dynamic effects, vertical deflections and
horizontal deflections. The National Annex for the country where the building is to be constructed should be consulted
for guidance. The UK National Annex[21] gives limits for deflections; limits for specific projects should be agreed with
the client if they differ from the proposed limits.
Informative Annex BB of EN 1993-1-1[20] gives guidance for buckling of structural components in buildings. Guidance
is given for:
Plated structures
The provisions of BS EN 1993-1-5 [24] are mainly appropriate to the design of plate girders, where the elements of the
cross section are typically more slender. For building frames using hot rolled sections, there is little need to refer to this
Part, except for the design of webs subject to transverse forces due to concentrated local forces (commonly referred to
as the determination of web bearing and buckling resistances).
Section 6 of BS EN 1993-1-5 [24] gives a method for determining the resistance of webs to transverse forces. This
method should only be used for rolled I and H sections and welded girders. Although not stated, the method should not
be used for structural hollow sections as it gives a single check that combines the web bearing and buckling effects.
For structural hollow sections, the NCCI method given in SCI P363 and SCI P374 should be used.
BS EN 1993-1-5 [24] also provides guidance on calculating the effective section properties of slender cross sections.
Design of joints
14 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
BS EN 1993-1-8 [25] gives rules for the design of joints between structural members. Both bolted and welded
connections are covered.
Note that a joint is defined as a zone where two or more members are interconnected and a connection is the location
where elements meet and is thus the means to transfer forces and moments.
BS EN 1993-1-8 [25] gives guidance for the design of joints subject to predominantly static loading. The steel grades
covered are S235, S275, S355 and S460. BS EN 1993-1-8 [25] uses the so-called component model to identify the
resistance of each component making up a joint. Consideration of each of these resistances allows the joint resistance
to be identified.
BS EN 1993-1-8 [25] classifies joints according to their rotational stiffness as nominally pinned, rigid or semi-rigid and
according to their strength as nominally pinned, full-strength or partial-strength. The appropriate type of joint model to
be used in global analysis depends on this classification and the method of global analysis.
Although BS EN 1993-1-8 [25] provides a method of calculating connection stiffness, a connection may be classified on
the basis of previous satisfactory experience. The UK National Annex states that connections designed in accordance
with the principles of SCI P358 are nominally pinned; those in accordance with the principles of SCI P398 are rigid.
Detailed design guidance is provided for simple connections in SCI P358 and for moment resisting connections, in SCI
P398.
Maximum permissible element thicknesses, reference stresses and toughness qualities for different reference
temperatures and steel grades are given in Table 2.1 of BS EN 1993-1-10 [26]. These should all be considered as part
of the material specification.
PD 6695-1-10[31] gives NCCI tables that will enable the determination of maximum permissible thicknesses without
considering the individual adjustments and without reference to Table 2.1 in BS EN 1993-1-10 [26]. It simplifies the use
of BS EN 1993-1-10 [26] for buildings in the UK and is recommended for buildings in the UK.
Fracture toughness guidance given in BS EN 1461 [38] should be used for hot dip galvanized elements.
15 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
Composite structures
Composite beam
When designing a steel and concrete composite building, the following parts of BS EN 1994 Eurocode 4: Design of
composite steel and concrete structures will be required:
Within these Parts, reference is made to BS EN 1993 (Eurocode 3) and to BS EN 1992 Eurocode 2: Design of
concrete structures, notably to:
SCI has produced guidance on the design of composite floors in accordance with Eurocode 4 (SCI P359).
Structural steel
The guidance given in BS EN 1994-1-1 [29] relates to structural steel grades up to S460. For steel properties reference
is made to BS EN 1993-1-1 [20].
For structural concrete BS EN 1994-1-1 [29] refers to BS EN 1992-1-1 [18], although it omits the lowest and highest
grades given in that code by only covering:
It also refers to BS EN 1992-1-1 [18] for the properties of reinforcing steel. However, it should be noted that
BS EN 1994-1-1 [29] permits the design value of the modulus of elasticity for reinforcing steel to be taken as equal to
that for structural steel given in BS EN 1993-1-1 [20], i.e. 210 kN/mm rather than 200 kN/mm.
16 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The reinforcement industry in the UK has decided to standardise on grade 500C steel.
Shear connectors
BS EN 1994-1-1 [29] refers to BS EN ISO 13918 [39] , which covers a range of stud diameters from 10 mm to 25 mm and
two materials - structural steel and stainless steel.
BS EN 1994-1-1 [29] refers to Sections 3.1 and 3.2 of BS EN 1993-1-3 [40] for the material properties of profiled steel
sheeting.
First order analysis can be used unless the effects of the deformed geometry significantly modify the structural
behaviour, in which case either modified first order effects should be determined or a second order analysis carried
out. BS EN 1994-1-1 [29] gives rules under four headings for the following types of global analysis:
Linear elastic analysis, in which allowance is made for cracking of concrete, creep and shrinkage
Non-linear global analysis, which generally follows the rules for plastic global analysis in BS EN 1993-1-1 [20]
and takes account of the behaviour of the shear connection
Linear elastic analysis with limited redistribution, which may be used where second order effects do not need
to be considered
Rigid plastic analysis, for which limitations at plastic hinge locations are given.
Generally, plastic analysis is used as it enables more economic designs. For serviceability limit states, elastic analysis
should be used, but where necessary, consideration of concrete cracking should be made.
Section classification
The section classification in BS EN 1993-1-1 [20] is adopted for composite sections. Where a steel element is attached
to a reinforced concrete element, the classification of the element can, in some cases, be improved. Requirements for
ductility of reinforcement in tension are given for Class 1 and Class 2 cross sections.
Modular ratio
For linear elastic analysis, the modular ratio for concrete is required. BS EN 1994-1-1 [29] gives an expression that
depends on the creep coefficient, as defined in BS EN 1992-1-1 [18], and a factor that takes into account the type of
loading.
17 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
The design bending resistance of a composite section may be determined by elastic analysis and non-linear theory for
any class of cross section; for Class 1 or Class 2 cross sections, rigid-plastic theory may be used see SCI P359 .
Plastic resistance moments of composite sections may be determined either assuming full interaction between the
steel and reinforced concrete or assuming partial shear connection , i.e. when the force transferred to the concrete is
limited by resistance of the shear connectors.
The resistance of a composite section to vertical shear is generally taken simply as the shear resistance of the
structural steel section. Where necessary, the resistance of uncased webs to shear buckling should be determined in
accordance with BS EN 1993-1-5 [24].
Shear Connection
Rules for the verification of the shear connection in composite beams are given in Section 6.6 of BS EN 1994-1-1 [29].
Detailed rules are only given for headed stud connectors. Dimension limits and rules for transverse reinforcement are
given. Natural bond between the concrete and steel is ignored.
BS EN 1994-1-1 [29] gives the design shear resistance of a headed stud connector as the smaller of the shear
resistance of the stud and the crushing strength of the concrete around it. When used with profiled steel sheeting, a
reduction factor, based on the geometry of the deck and the height of the stud, is used to reduce the resistance of the
shear connectors. Stud connectors have sufficient ductility to develop plastic behaviour, provided that certain limits
are observed if there is only partial shear connection.
Limitations are given on the use of partial shear connection, i.e. for situations where the design shear resistance over a
length of beam is insufficient to develop the full resistance of the composite beam. This will often be a critical design
criterion for long-span beams.
The longitudinal shear resistance of a slab is calculated using the procedure given in BS EN 1992-1-1 [18]. However,
the shear planes that may be critical and the contributions from the reinforcement or the profiled steel sheeting (if the
shear connectors are through-deck welded) are defined in BS EN 1994-1-1 [29].
18 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
No limits are given for vertical or horizontal deflections. However, Section 7.4 of BS EN 1994-1-1 [29] does give details
of the minimum reinforcement required to satisfy crack width limits.
Connection design
Composite connection
design guide (SCI P213)
For composite joints, such as where there is a double-sided beam-to-column joint and the composite slab is
continuous, BS EN 1994-1-1 [29] provides supplementary rules to those in BS EN 199318 [25] to verify the connections.
Rules are also given for column web panels in shear or transverse compression when encased in concrete see SCI
P213.
CB/203 Design
CB/203 is the BSI committee responsible for the British Standards for the design and execution of steel structures,
and for the UK input to CEN/TC 250/SC 3 Eurocode 1993 Design of steel structures and Eurocodes related
documents. It also mirrors CEN/TC 135 Execution of steel and aluminium structures, and ISO/TC 167 Steel and
aluminium structures.
Every 6 months CB/203 publishes a Summary Report to Stakeholders, which lists the design and execution
standards under CB/203 responsibility, the standards due for Enquiry/Vote/Systematic Review, and provides an
update on CEN and ISO Activities. The latest version is available below, along with a comments template for the
Eurocodes Systematic Review and a more general template for those who use the standards that fall within the scope
of CB/203 to comment on their good/bad experiences with the standards and to provide technical comments on them:
19 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
References
1. ^ BS 5950 Structural use of steelwork in building: Various parts, BSI
3. ^ 3.03.13.23.3Approved Document A (Structure) 2004 Edition incorporating 2004, 2010, and 2013 amendments.
Department for Communities and Local Government
4. ^ Approved Document A (Structure) 2004 Edition incorporating 2010 amendments (Welsh Government)
7. ^ 7.07.1 BS EN 1991-1-1: 2002 Eurocode 1. Actions on structures. General actions. Densities, self-weight,
imposed loads for buildings, BSI
9. ^ 9.09.1 BS EN 1991-1-2: 2002 Eurocode 1. Actions on structures. Actions on structures exposed to fire, BSI
10. ^ 10.010.110.210.3 NA to BS EN 1991-1-2: 2002 UK National Annex to Eurocode 1. Actions on structures. General
actions. Actions on structures exposed to fire, BSI
11. ^ 11.011.1 BS EN 1991-1-3:2003+A1:2015, Eurocode 1. Actions on structures. General actions. Snow loads, BSI
13. ^ 13.013.113.2 BS EN 1991-1-4:2005+A1:2010 Eurocode 1. Actions on structures. General actions. Wind actions,
BSI
15. ^ 15.015.1 BS EN 1991-1-5:2003, Eurocode 1. Actions on structures. General actions. Thermal actions, BSI
16. ^ 16.016.116.2 BS EN 1991-1-6: 2005, Eurocode 1. Actions on structures. General actions. Actions during
execution, BSI
17. ^ 17.017.117.2 BS EN 1991-1-7:2006. Eurocode 1: Actions on structures. General actions. Accidental actions. BSI
18. ^ 18.018.118.218.318.418.5 BS EN 1992-1-1:2004. Eurocode 2: Design of concrete structures. General rules and rules
for buildings. BSI
19. ^ 19.019.1 BS EN 1992-1-2: 2004 Design of concrete structures. General rules. Structural fire design, BSI
20. ^ 20.0020.0120.0220.0320.0420.0520.0620.0720.0820.0920.1020.1120.1220.1320.1420.1520.1620.1720.1820.1920.2020.21 BS EN
1993-1-1:2005+A1:2014, Eurocode 3: Design of steel structures. General rules and rules for buildings, BSI
22. ^ 22.022.1 BS EN 1993-1-2: 2005 Eurocode 3. Design of steel structures. General rules. Structural fire design,
BSI
20 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
26. ^ 26.026.126.226.326.4 BS EN 1993-1-10:2005 Eurocode 3. Design of steel structures. Material toughness and
through-thickness properties, BSI
27. ^ 27.027.127.2 BS EN 1993-1-12: 2007, Eurocode 3. Design of steel structures. Additional rules for the extension
of EN 1993 up to steel grades S 700, BSI
28. ^ 28.028.1 BS EN 1993-2: 2006 Eurocode 3. Design of steel structures. Steel bridges, BSI
30. ^ 30.030.1 BS EN 1994-1-2: 2005, Eurocode 4. Design of composite steel and concrete structures. General rules.
Structural fire design, BSI
31. ^ 31.031.1 PD 6695-1-10:2009 Recommendations for the design of structures to BS EN 1993-1-10. BSI
32. ^ 32.032.132.2 NA to BS EN 1990:2002+A1:2005 UK National Annex for Eurocode. Basis of structural design. BSI
33. ^ 33.033.1 BS EN 1993 Eurocode 3: Design of steel structures. Various parts, BSI
34. ^ BS EN 1994 Eurocode 4: Design of composite steel and concrete structures. Various parts, BSI
35. ^ BS EN 10025-2: 2004, Hot rolled products of structural steels. Technical delivery conditions for non- alloy
structural steels, BSI
36. ^ BS EN 10210-1: 2006, Hot finished structural hollow sections of non-alloy and fine grain steels. Technical
delivery requirements, BSI
37. ^ BS EN 10219-1: 2006, Cold formed welded structural hollow sections of non-alloy and fine grain steels.
Technical delivery requirements, BSI
38. ^ BS EN 1461: 2009 Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test
methods, BSI
39. ^ BS EN ISO 13918: 1998, Welding. Studs and ceramic ferrules for arc stud welding, BSI
40. ^ BS EN 1993-1 -3:2006 Eurocode 3. Design of steel structures. General rules. Supplementary rules for cold-
formed members and sheeting, BSI
Further reading
Steel Designers' Manual 7th Edition. Editors B Davison & G W Owens. The Steel Construction Institute 2012,
Chapters 1 and 3
Eurocode guides to EN1993 and EN1994 from ICE publishing (Thomas Telford).
Resources
SCI AD346, Design actions during concreting for beams and decking in composite floors, 2010
NCCI: Elastic critical moment for lateral torsional buckling (SN003b EN EU) SCI
SCI P359 Composite Design of Steel Framed Buildings, 2011
SCI P361 Steel Building Design: Introduction to the Eurocodes, 2009
SCI P362 Steel Building Design: Concise Eurocodes, 2009
SCI P363 Steel Building Design: Design Data, 2013
A web-based interactive version of the 'Blue Book', is also available.
21 / 22
http://www.steelconstruction.info/Design_codes_and_standards - 18th April 2017
SteelConstruction.info
The free encyclopedia for UK steel construction information
SCI P374 Steel Building Design: Worked Examples - Hollow Sections, 2009
SCI P213 Joints in steel construction: Composite connections, 1998
SCI P358 Joints in Steel Construction - Simple Joints to Eurocode 3, 2014
SCI P398 Joints in Steel Construction - Moment-resisting Joints to Eurocode 3, 2013
SCI P394 Wind Actions to BS EN 1991-1-4, SCI, 2013
Wind loading calculator
See also
Steel material properties
Composite construction
Modelling and analysis
Allowing for the effects of deformed frame geometry
Member design
Simple connections
Moment resisting connections
Structural fire resistance requirements
Steelwork specification
Structural robustness
External links
UK Building Regulations
CEN
NCCI for steel design
bsi
CPD
An introduction to Eurocode 3