Professional Documents
Culture Documents
tilter
Ballast
Assembly
Socket
Reflector
Reflector
Gasket
Def Iector
Befractor
rin g
Re{ractor
Toggle latch
o
[,4ccraw Ed son
I ENGI N EEBING ANALYSIS-cr
and vertit
Consta nts
. 30' Street Width
. 23' l\ilounting leight
. 6' Arm Length
RESILITE
Co! ld use
for
rcsrdent a
ie-od c r
streets
.Crw
s.c lar restdenlial streeis R-oconrmend 3 f rirres p,.
6(10 bock \,r' th 200 fxture spacnll Recomrcnd
150 I xtLrre spac ng al |-rtersectrons nnd 190' r)|
oo* cross sireets lo rarsc Lght evel arrd Lrnriornr ty
3. Res rte !trlz ng 750n/ HPS rs pcrfcct so/!/ro|
lat nat"l atlcttes ead ng through res denl n areas
4. Rcs lrtc s /nost ecolrol/r,cal so/rrarn s nc,. !t e:rter
reslr 1s are aah ovoal w th le!!er irxt!res
Application Cuiclelines
1. ES recornmondat on for ras dcnl a streris is 4 I-c na n
ia n-od ar-rd 6 10 I av,oraqe to Tn nrm! Tl un lorm ly From lh"
.bove i;bic 150W Resr te can be sDac,.d 2,15 and |eet
ths cfrteflon Typca horzonlal larip can ory br spaa-.d
T80 and typ ca veft ca an]p 190
2. N4cGra,r Ealison reconimcndat ons lor resrdcrlia roaal
\r/iiys p ace more -omphas s on !n form ty thar'l ol iootcand -'
perlormance n any app cetion ut LZ ng very o\,,, fooican
d es. o\,/ l/lAX MU[4 TO M N t!4ull ln]form ty e rm naies a
Poo of Light !nd-.r the lum na re ther-.by mprov lg
seaurty for ihe ent re area !l/e recom.llend d 6 to I l'/lAX
MUlvl lO M N MLI[4 Lrn forni ty ald approx malc y ,l Fc
S-comparing Besilite luminaire to typical horizontal lamp
vertical lamp street lighting fixtures.
(Recommended rnountlng he ght ' 1'Pole Set Back
and bracket length to avoid 'Type lll [,4ed]um Photometric Distributron
interlerence from lree llranches.) . Staqqered Fixture Spacing
Co! ld use
Too h gh Too hiqh Poor hot Poor hot lor Poor- hot Poor hot
lent for ior spots and spots and G ood resrdenlral spots and spots and
res dent a r-osrdential dark areas dark areas teeder dark areas.
streets
1. C osest spac ng (150') does not compare to Resr 1. 1BO'spacing does not compare to Resilrte at 2501
and lite at 2501 2. Therefore imited 1o use in owest wattage and
2. Therefore f xture s I m ted to use on ma n streets close spacing lor acceptable max/mln uniform ty.
ltotj where h qh iqht leve s are required and high mount 3. Use Resilite
per lrg and c ose spacrng are permrtted.
end 3. tlse Res lrte
on
eas
aler
I
Orclering Infirrmation
ffl
ruasr Mast Arm Top Ba llast High Pressure IES Light
/ t
anrvr ,r,"
EPA t-
Mount (2) Mount (3) Type (4) Sodium Lamp (5) Pattern (9J
S PECI FICATIO N
The lum na re shall be McGraw-Edison Resillte caialog Reflector gasket shall be whrte polyester felt attached to
number (specify) and shall include the following features: the lower flange of the reflector. lt shall provide a cushion
Luminaire housing shall be die cast aluminum and con- between the reflector and refractor and seal ihe optical
tain the bailast asserrbly, socket and reflector assembly system against the entrance of external contaminants.
It shall mouni on (3-inch O. D pole top) (McGraw-Edison Belractor shall be prismatic borosil cate glass and shall
wall bracket) (1%-inch pipe size, mast arm tenon) or (top produce (asymrnetric) (symmetric) IES type light patterns.
mount with 1%-inch pipe size threaded n pple). Houslng Refractor ring shall be die cast aluminum wiih iniegral
for wall bracket or mast arm mounting shall be (with)(with- cast hinge pins. lt shall have an external, positive-closing,
out) photocontro receptacle. togg le type latch.
Photometric perlormance Lurninaire efficiency shall not High pressure sodium lamp ballast shali be autotransformer
be less than 657" of the bare lamp with not less than 40% reactor hlqh power factor type rated (70) ( 100) ('150..) watts with
of the bare lamp lumens being directed to the downward an inpur of (120) (208) (240) (277) (480) volts
street side of the lurninarre and not more than 20% curb Terminal block shall be a high grade electrical phenolic
side. Upward component shall not exceed 4% Performance
rnaierial. lt shall be located to permit easy connection of
shall be such that the light projected upon the roadwav luminaire leads and service leads. lt shall accommodate
shall decrease uniformly without excessive striations as conductors up to #6 A.WG
the distance is increased from the luminaire
Photocontrol receptacle (where applicablei shall be fric-
Sliplitter shall have iniegral cast lugs designed to align tion rotation type allowing proper positioning of photo-
the luminaire. lt sha have a srngle hex head bolt to hold control without the use of tools, and shall meet EEI-NElVlA
housing securely. requirernents for 3.terminal, polarized, lock-in type recep-
Reflector shali be removab e, and shall be hlghly pol shed tacles. Luminaires shall be connected to provide (specify)-
aluminum treated to provide a specular surface and shall volt operation of the photoelectrlc control.
be fluted design. lt shal be consiructed from corrosion- Finish shall be thermoset acrylic enamel-aluminum,
resistant sheet aluminum finished with Alzak process. black or bronze color
Socket-tilter shall be neoprene-coated flberglass and shall - LamFi rr. ral ng ol55 vo ts
be posltioned around the socket in such a manner that it
shall allow circulation of air through the optical assembly HALO LIGHTING
and effectively filter out external coniaminants.