Professional Documents
Culture Documents
h selecta
Now wit o lo gy
Multifunction relay MK 7850N/200 chn
Plugin te
multitimer
All technical data in this list relate to the state at the moment of edition. We reserve the right
for technical improvements and changes at any time. 1 MK 7850N/200 / 11.09.06 e
Function diagram Function diagram
UH UN
USt UN
B1-A2
0
ta tb tc td
UH UN
position function switch
A1-A2
0 15-18
1 AV t1
t1=ta+tb+tc
USt UN 15-16
B1-A2
0 15-18
ta tb tc td 2 EW t1
t1=ta+tb+tc
15-16
t 15-18 IE t1 t2 15-18
2 EW t=ta+tb+tc t1=ta+tb+tc t2=te+tf
15-16 S1: B* 15-16
t t 15-18 TP t2 t1 t2 15-18
4 BI t=ta+tb+tc t=te + tf t2=ta+tb+tg t1=th+ti
15-16 S1: B* 15-16
UH UN UH UN
A1-A2 A1-A2
0 0
USt UN USt UN
B1-A2 B1-A2
0 0
15-18 t1 t1 t1 15-18
5 RV t t t 5 RV
15-16 15-16
15-18 t1 t1 t1 t1 15-18
6 IF t t t t 6 IF
15-16 15-16
15-18 AW t1 t1 t1 15-18
7 AW t t t
15-16 S1: A* 15-16
7
15-18 EW/AW t2 t1 t2 t1 t2 15-18
8 AV/RV t t t t
15-16 S1: B* 15-16
M8290
t1 t2 t1 t2 15-18
8 AV/RV
15-16
M8291
MK 7850N/200 MK 7850N/500
... = position of function switch ... = position of function switch
AV = Delay on energisation RV = Delay on de-energisation AV = Delay on energisation RV = Delay on de-energisation
EW = Fleeting on make IF = Pulse forming function EW = Fleeting on make IF = Pulse forming function
IE = Delayed pulse AW = Fleeting on break IE = Delayed pulse AW = Fleeting on break
BI = Flasher, AV/RV = Delay on energisation and S1 in positon A: S1 in position A
start with pulse de-energisation t1: adjustable, t2 = 0,5 s fixed EW/AW = Fleeting on make
S1 in position B: and break
t1 and t2 adjustable S1 in position B
TI = Cyclic timer, AV/RV = Delay on energisation
start with pulse and de-energisation
S1 in position A
TP = Cyclic timer,
start with break
S1 in position B
2
Circuit diagrams Notes
Control input B1
t
Z1 Z2 The functions RV, IF, AW, AV / RV have to be controlled via input B1
(+) with voltage against A2. The control signal could be the same as
25 B1 25 B1 the auxiliary/control voltage of A1 or any other voltage between 12 and
A1 15 A1 15
21 (+) 21 (+)
240 V AC or DC. Operating a parallel load between B1 and A2 is also
X3 Z1 Z2 X3 possible.
A1 B1 15 25 A1 B1 Z1 15 25
21 21 If with function IF the inputs A1 and B1 are controlled simultaneously
a pulse with the adjusted length is started. With the variant MK7850N/
500 the output pulse can be disabled by setting the slide switch in
26 28 26 28 Position "B".
A2 16 18 22 24 A2 Z2 16 18 22 24
26 28 26 28
22 24
X1 X2
M8100_a 22 24
X1 X2 Time interruption and time addition with X3
M8676_a
On all functions, also with RV,IF, AW (EW/AW) and AB/RV the time
16 18 A2 16 18 A2 delay can be interrupted during timing by bridging the terminals
X2 - X3. By opening the bridge the time continues (time addition).
MK 7850N.82/200 MK 7850N.82/300 While X2 and X3 are bridged the control input is disabled and the yellow
LED remains in the state it had at stop. No external voltage must be
t1
Z1 connected to X2 and X3 as the unit may be damaged.
Z2
Z3
t2 Remote potentiometers
A1 15
25 B1 Both settings on variant MK 7850N/500 can also be made by remote
21 (+) potentiometers of 10 kOhms:
Z1 Z2 Z3 X3 - terminals Z1 - Z2: potentiometer for time t1
- terminals Z2 - Z3: potentiometer for time t2
A1 B1 Z1 15 25 When connecting a remote potentiometer the corresponding
21
potentiometer has to be set to min. If no remote potentiometers are
required the terminals Z1-Z2 resp. Z2-Z3 have to be linked.
26 28 The wires to the remote potentiometers should be installed separately
A2 Z2 Z3 16 18 22 24 from the lines with mains voltage. If this is not possible, a screened
26 28 cable is recommendet where the shield is connected to Z2.
X1 X2
22 24 M8101_a To terminals Z1, Z2 and Z3 no external voltage must be connected,
16 18 A2 as the unit might be damaged.
3
Technical data Technical data
Output Dimensions
General data
4
Standardtype Connection examples
Variants L(+)
Nominal voltage
Variant Control with parallel connected load
Type of terminals
without indication:
terminal blocks fixed, L(+) AC/DC12...240V
with screw terminals
PC (plugin cage clamp): DC24V
plugable terminal
blocks with cage S1
e.g. PLC
clamp terminals semi-
PS (plugin screw): conductor
plugable terminal A1 B1(+) output
blocks with screw
terminals
Contacts
Type MK7850N
Accessories
A2
AD 3: External potentiometer 10 k
N(-)
The external potentiometer is used for M8292
remote setting of the time delay. The
internal potentiometer of the timer must Connection with 2 different control voltages.
be set to min. time delay.
Degree of protection
front side: IP 60
5
E. DOLD & SHNE KG D-78114 Furtwangen P.O. Box 1251 Phone +49 7723 / 65 40 Fax +49 7723 / 654 356
e-mail dold-relays@dold.com internet http://www.dold.com
6