Professional Documents
Culture Documents
currency: $
I am looking for
advanced search
(0) in Basket
RET-MONITOR F1-MONITOR
Click the
covers for
world
You Are Here: Home / RET-Monitor / bearings / Bi-metal Journal bearings: Materials and construction
Tags : bearings
0 Comments
Traditional main bearing construction is based on a three-layer bearing made of a steel backing, a bearings
hard mid layer and a thin overlay of a soft material.
The bi-metal bearing is constructed of only two layers, consisting of a steel backing with an inlay of an aluminium
alloy. Typical bearing materials used in the construction of bi-metal bearings are a combination of the following
materials: Tin, silicon, lead, copper and aluminium. The bearing material may sometimes be described as aluminium-
silicon. The silicon is what bearing manufacturers have determined make aluminium a preferred material for modern
bearing applications. The small particles of silicon, are finely and evenly dispersed throughout the bearing material,
and since it's an alloy, it can maintain its properties throughout the entire bearing thickness resulting in a more
consistent, reliable performance.
Debris is a major cause of bearing failure and it can be left over from machining operations or due to wear of the
component parts. Debris can get trapped between the journal and the bearing surface and lead to damage of the
bearing surface and/or scoring of the journal, and could ultimately lead to failure. Debris is an important point with
bi-metal bearings due to issues over embeddability.
Bi-metal bearings are considered harder than tri-metal bearings. The surface of the bearing contains hard and soft
areas where the soft areas allow embeddability, whilst the harder areas do not. Embeddability is the ability to embed
hard particles and foreign debris within the bearing material. However, due to the hard and soft nature of the
bearing surface, it is possible for debris to become trapped between the bearing surface and the journal leading to
wear. Therefore, to counteract this effect, the bi-metal bearing is machined with micro-grooves to retain the hard
particles, these particles eventually being washed away by the lubricating oil.
bearings Bi-metal-journal-bearing
Note that the different combinations and quantities of alloying materials, as used by the different manufactures, will
provide different bearing characteristics. Whereas the aluminium-silicon alloy may produce a hard bearing with
partial embeddability, another aluminium alloy mix may provide a bearing that offers much improved embeddability
and higher load carrying capabilities.
Bi-metal bearings do possess conformability, which is the ability to adjust to minor misalignments during assembly.
In general tri-metal bearings are said to have a greater load carrying capacity then aluminium bi-metal bearings. In
terms of bearing selection, that is, whether to use tri-metal or bi-metal bearings, it may come down to how much
load the bearings have to withstand and the life expectancy of the bearings. For example, bi-metal journal bearings
may be used in a high load application for a short period of time; for example a drag car, having one or two runs. If
high load carrying characteristics and longevity are required, then tri-metal bearings may be selected. This example
of bearing selection is not meant to be exhaustive, but to illustrate that a trade off between the two bearing types
has to be made. Note also that cost will also be a factor.
In comparing bi-metal to tri-metal in severe load applications, there will no doubt be some cases where the bi-metal
bearings will outperform those of tri-metal. If the roughness of the sliding surfaces is reduced, the load carrying
capacity of the bearing is increased. Hence concentrating on bi-metal bearings in this way, could provide load
carrying benefits.
The future trend for journal bearings may be headed toward the bi-metal type, but tri-metal bearings are still in
demand. In all probability, bi-metal and tri-metal journal bearings may continue to co-exist for quite some time.
Aluminium alloy journal bearings are not new. What has propelled them forward are possibly the latest methods of
manufacture and the inclusion of materials such as silicon. Bi-metal bearings have the benefit of higher melting
points and greater fatigue surface strengths, than tri-metal bearings.
Comment
ADD COMMENT
Sponsored By
Categories
advanced-materials
alternative-energy
bearings
camshafts
coatings
con-rods
coolant-system
crankshafts
electronics
engine-structure
exhausts
fasteners
fuel-system
induction-system
oil-system
pistons-rings
surface-treatments
test-equipment
transmission
valvetrain
Archive
2014
Nov (Issue 48)
2013
Nov (Issue 40)
2012
Nov (Issue 32)
2011
Dec/Jan (Issue 25)
2010
Dec/Jan (Issue 17)
Jan (Issue 9)
2009
Dec (Issue 8)
Nov (Issue 7)
Oct (Issue 6)
Sep (Issue 5)
Aug (Issue 4)
Jul (Issue 3)
Jun (Issue 2)
May (Issue 1)
Sign up to our RET-Monitor & F1-Monitor technical newsletters that can be tailor made to cover the areas of the
race engine / F1 car youre most interested in. Whats more theyre 100% FREE!
HPM Info
> About HPM
> Advertise
> Editorial Team
> Contact Us
Helpful Information
> Worldwide Distributors
> FAQs
> Terms & Conditions
> Secure Ordering
> Cookie Policy
> Sitemap
Keep updated
Follow our latest news below
Blog Latest
Properties and applications of titanium
Titanium is a strange material, not least for the myths surrounding it. It is often described as being incredibly hard, or incredibly strong, when the
truth is that it is neither. It can be impressively strong compared to its density, but it does not stand out in this respect. It has been very ex read
article
High Power Media Ltd | Whitfield House, Cheddar Road, Wedmore, Somerset, BS28 4EJ, England Website Design and Content Management
System by Fat Media