Professional Documents
Culture Documents
2. Pulverized coal is
(A) coal free from ash
(B) non-smoking coal
(C) coal which bums For long time
(D) coal broken into fine particles.
7. In a power plant, coal is carried from storage place to boilers generally by means of
(A) bucket
(B) V-belts
(C) trolleys
(D) manually.
11. Power plants using coal work closely on known which of the following cycle ?
(A) Otto cycle
(B) Binary vapor cycle
(C) Brayton cycle
(D) Rankine cycle.
14. Which of the following contributes to the improvement of efficiency of Rankine cycle in a thermal power plant ?
(A) Reheating of steam at intermediate stage
(B) Regeneration use of steam for heating boiler feed water
(C) Use of high pressures
(D) All of the above.
16. When pulverized fuel is not used, the equipment used for supplying coal to the boiler is
(A) Heater
(B) Stoker
(C) Burner
(D) Skip hoist.
22. The equipment installed in power plants to reduce air pollution due to smoke is
(A) Induced draft fans
(B) De-super heaters
(C) Electrostatic precipitators
(D) Re-heaters.
26. What is the maximum size of steam turbine usually being installed, for thermal power plants ?
(A) 120 MW
(B) 250 MW
(C) 500 MW
(D) 1000 MW.
28. Which of the following is not the voltage at which power is usually transmitted
(A)132 kV
(B) 66 kV
(C) 33 kV
(D) 20 kV.
33. Bagasse is
(A) low quality coal
(B) a fuel consisting of wood
(C) fibrous portion of sugarcane left after extracting the juice
(D) a kind of rice straw.
39. Steam pressure in modem thermal plants of 100 MW and above capacity may be exacted to be
(A) 10 kg/cm2
(B) 50 kg/cm2
(A) up to 100kg/cm2
(D) more than 100 kg/cm2.
40. The overall efficiency of a boiler in a thermal power plant is of the order of
(A)10%
(B) 25 to 30%
(C) 40 to 50%
(D) 70 to 80%.
46. The steam consumption per kWh of electricity generated in a modem power plant is of the order of
(A) 1-2 kgs
(B) 2-4 kgs
(C) 5-7 kgs
(D) 10-12 kgs.
47. For low head and high discharge, the hydraulic turbine used is
(A) Kaplan turbine
(B) Francis turbine
(C) Pelton wheel
(D) Jonual turbine.
53. In a hydro-electric plant a conduct system for taking water from the intake works to the turbine is known as
(A) Dam (B) Reservoir (C) Penstock (D) Surge tank.
67. Caking is
(A) making cakes of coal out of fine powders
(B) a variety of free burning coals
(C) coal produced from burning of wood in inert atmosphere
(D) in boiler furnace some coals become plastic and form lumps or masses of coal.
Contact Us : Mithilesh Singh (9827482029) Email : mithileshkhudawal@gmail.com
website link: http://mithileshkhudawal.wix.com/boeindia
IBCI is the Premier BOE Coaching Institution in Raipur (India),where dream convert into reality in very short
duration
IBCI (Indian BOE Coaching Institute)
Study material for BOE examination preparation
MCQ(Multiple choice question) on Power Plant Engineering :
68. 1 atomic mass unit is equal to
(A) 1.66 x 10 -27 kg
(B) 1.66 x 10-25 kg
(C) 1.66 x 10 -17 kg
(D) 1.66 x 10-10 kg.
69. Particles having the same atomic number but different mass numbers arc called
(A) Positrons
(B) Beta particles
(C) Isotopes
(D) Decayed panicles.
(A) 1245
(B)1235
(C) 12461
(D) 12345.
89. Which engine will have highest efficiency, between given temperature limits ?
(A) Carnot cycle
(B) Otto cycle
(C) Diesel cycle
(D) Dual cycle.
93. How many kg of air are required for the combustion of one kg of diesel fuel ?
(A) 1 kg
(B) 1.3 kg
(C) 4 kg
(D) 15 kg.
94. Due to burning of 1 kg of pure carbon with a minimum quantity of air required, the percentage of carbon dioxide in the exhaust
gas would be
(A) 10%
(B) 19%
(C) 29%
(D) 39%.
98. If a engine has spark plug, it can be safely concluded that the engine is
(A) not a diesel engine
(B) a two stroke petrol engine
(C) a four stroke petrol engine
(D) an air cooled petrol engine.
106. The temperature at which a lubricating oil will give off sufficient vapors to form combustible mixture with air, is known as
(A) Flash point
(B) Fire point
(C) Pour point
(D) Combustion point.
112. Which of the following will not assist in getting high power output from a compression ignition engine ?
(A) High compression ratio
(B) Fine atomization of fuel
(C) High charge density
(D) Large quantity of excess air.
116. A mixture containing 60% cetane and 40% Iso-octane will have
(A) cetane number 60
(B) cetane number 40
(C) octane number 40
(D) none of the above.
120. Out of the following diesel engines, the minimum air consumption per BHP will be in
(A) 4 stroke, mechanical injection
(B) 4 stroke, air injection
(C) 2 stroke, air injection
(D) 2 stroke, mech. injection, pump scavenging.
121. For the same maximum pressure and heat input the most efficiency cycle is
(A) Brayton cycle
(B) Otto cycle
(C) Diesel cycle
(D) Dual cycle.
Contact Us : Mithilesh Singh (9827482029) Email : mithileshkhudawal@gmail.com
website link: http://mithileshkhudawal.wix.com/boeindia
IBCI is the Premier BOE Coaching Institution in Raipur (India),where dream convert into reality in very short
duration
IBCI (Indian BOE Coaching Institute)
Study material for BOE examination preparation
MCQ(Multiple choice question) on Power Plant Engineering :
122. For the same temperature limits and heat input, the most efficient cycle is
(A) Carnot cycle
(B) Otto cycle
(C) Diesel cycle
(D) Brayton cycle.
124. Which of the following is not a part of diesel engine power plant ?
(A) Cooling tower
(B) Penstock
(C) Oil pump
(D) Strainer.
125. Of the total heat supplied to a diesel engine plant, which one has the highest proportion ?
(A) Useful output
(B) Heat lost to cooling water
(C) Heat lost in exhaust gases
(D) Heat loss in friction radiation, etc.
127. Which power plant cannot have single units of 100 MW capacity?
(A) Steam power plant
(B) Nuclear power plant
(C) Hydroelectric power plant
(D) Diesel engine power plant.
128. In a thermal power plant, heat from the flue gases is recovered in
(A) chimney
(B) de-super heater
(C) economizer
(D) condenser.
130. In a super-heater
(A) pressure rises, temperature drops
(B) pressure rises, temperature remains constant
(C) pressure remains constant and temperature rises
(D) both pressure and temperature remains constant.
131. Bagasse is
(A) a variety of coal
(B) a fuel consisting of wood etc.
(C) fibrous portion of sugarcane left after extracting the juice
(D) a kind of rice straw.
134. For the same cylinder size and rpm which engine will produce more power ?
(A) Gas engine
(B) Petrol engine
(C) Diesel engine
(D) Super-charged engine.
138. The efficiency of an otto cycle will approach that of Carnot cycle when
(A) engine is operated at high rpm
(B) engine is run at high load
(C) constant volume processes are replaced by isothermal processes
(D) adiabatic processes are replaced by isothermal processes.
140. Which instrument can be used to measure the flow of a liquid through a pipe ?
(A) Pitot tube
(B) Venturimeter
(C) Pressure gauge
(D) Orifice.
147. In which part of the steam power plant the pressure of steam is less than the atmospheric pressure ?
(A) Condenser
(B) Boiler
(C) Turbine
(D) Super beater.
150. In a steam power plant which pipe line section is invariably lagged ?
(A) pipes carrying steam from boiler to turbine
(B) pipes carrying water from condenser
(C) pipes carrying water from water treatment plant
(D) pipes carrying water from boiler feed pump to boiler.
153. When coal analysis gives fixed carbon, volatile combustible matter, ash and moisture the analysis is termed as
(A) ultimate analysis
(B) proximate analysis
(C) orsat analysis
(D) gross analysis.
155. Sulphur content of liquid fuels assumes importance from the point of view of
(A) efficiency
(B) heating rate
(C) corrosion
(D) firing rate.
157. Coking is
(A) formation of lumps or masses of coke in boiler furnaces at high temperatures
(B) heating of coal in absence of air, driving out CO2 and leaving behind the residue and carbon
(C) burning of coal in furnace
(D) producing lumps of coal from fine powders with the help of a binder.
159. The efficiency of steam generators is first a function of design. Beyond that, efficiency depends upon the loading and manner
of operation. Good operation consists in
(A) control and limiting of air
(B) minimizing combustibles in refuse and flue gas
(C) maintaining clean heat transfer surfaces
(D) all of the above.
160. Generally the major constituent of exhaust gases from a thermal power plant is
(A) oxygen
(B) carbon monoxide
(C) nitrogen
(D) carbon dioxide.
161. The compression ratio for diesel engines is generally in the range
(A) 5 to 10
(B) 14 to 22
(C) 10 to 14
(D) 22 to 30.
162. Binary vapor cycles are not finding favor with designers because
(A) ideal vapors are not available
(B) initial cost of such plants is high
(C) higher pressures demand thicker sections of piping
(D) such plants are suitable for high load factors only.
163. Thermal efficiency of a gas turbine cycle improves as a result of all of the following EXCEPT
(A) heating of air before compression
(B) inter-cooling of air
(C) reheating of gas
(D) multistage expansion.
164. Even with best possible arrangements, the thermal efficiency of a gas turbine cycle is always below
(A) 10%
(B) 20%
(C) 25%
(D) 40%.
165. The scavenging efficiency of a 4 stroke diesel engine is usually in the range
(A) 50% to 60%
(B) 60% to 75%
(C) 75% to 90%
(D) 95% to 100%.
172. The path followed by the gases discharged from chimney called the 'plume', depends on
(A) thermal properties of gases
(B) dynamic properties of gases
(C) wind direction
(D) all of the above.
177. In all of the following turbines the back pressure will be above the atmospheric pressure EXCEPT
(A) Topping turbine
(B) First turbine of repeat cycle
(C) Condensing turbine
(D) Non-condensing turbine.
Contact Us : Mithilesh Singh (9827482029) Email : mithileshkhudawal@gmail.com
website link: http://mithileshkhudawal.wix.com/boeindia
IBCI is the Premier BOE Coaching Institution in Raipur (India),where dream convert into reality in very short
duration
IBCI (Indian BOE Coaching Institute)
Study material for BOE examination preparation
MCQ(Multiple choice question) on Power Plant Engineering :
178. In bleeder turbines, part of the steam is extracted for
(A) heating secondary air
(B) fed water heating
(C) reheating
(D) condensation.
179. As compared to steam at entry to the turbine, which of the following will be larger at exit ?
(A) Pressure
(B) Flow rate
(C) Specific volume
(D) Specific enthalpy.
183. Small domestic electric power generators are usually of capacity around
(A) 10 kVA
(B) 5 kVA
(C) 1 kVA
(D) 100 VA.
190. In which of the following power plant the availability of power is least reliable ?
(A)Solarpowerplant
(B) Wind energy
(C) Tidal power plant
(D) Geothermal power plant.
193. In the Geysers steam is continuously vented through fissures in the ground. These vents are called
(A) vent holes
(B) pot holes
(C) fumaroles
(D) sun spots.
194. Geologists believe that below the earth's crust, the molten mass exists in the form of
(A) magma
(B) vent
(C) hot cell
(D) liquation.
197. In hydrothermal systems when steam, water and dissolved solids are available as source of energy, the entrained solids are
removed by
(A) filters
(B) centrifugal separators
(C) strainers
(D) none of the above
202. In petrothermal systems of geothermal energy there is hot dry rock but no underground water. In such systems energy is
obtained by
(A) circulating compressed air
(B) pumping water
(C) creating water wells
(D) none of the above.
203. Reflecting mirrors used for exploiting solar energy are called
(A) diffusers
(B) ponds
(C) heliostats
(D) mantle.
204. Which of the following area is preferred for solar thermal electric plants ?
(A) mountain tops
(B) hot arid zones
(C) coastal areas
(D) high rainfall zones.
210. A module is a
(A) newly installed solar cell
(B) series parallel arrangement of solar cells
(C) a series of solar cells when not used for power generation
(D) none of the above.
Contact Us : Mithilesh Singh (9827482029) Email : mithileshkhudawal@gmail.com
website link: http://mithileshkhudawal.wix.com/boeindia
IBCI is the Premier BOE Coaching Institution in Raipur (India),where dream convert into reality in very short
duration
IBCI (Indian BOE Coaching Institute)
Study material for BOE examination preparation
MCQ(Multiple choice question) on Power Plant Engineering :
211. The major disadvantage, with solar cells for power generation is
(A) lack of availability
(B) large area requirement
(C) variable power
(D) high cost.
214. Winds caused by greater solar heating of the earth's surface near the equator than near the northern or southern poles, are
known as
(A) local winds
(B) equatorial winds
(C) planetary winds
(D) trade winds.
219. All of the following are electrical mechanical storage systems EXCEPT
(A) Pumped hydro-system
(B) Torsion bar system
(C) Super-conducting coils
(D) Kinetic flywheels.
228. The presence of CO2 and H2O in the atmosphere results in absorption of
(A) short wave ultra-violet radiations
(B) visible wavelengths of spectrum
(C) long wave infrared radiations
(D) all of the above.
229. Return to earth of the oxides of sulphur and nitrogen occurs in the form of
(A) acid rain
(B) acid snow
(C) acid fog
(D) any of the above.
238. Cleat is
(A) main joint in a coal seam along which it breaks most easily
(B) floor of a coal seam
(C) carton and sulphur compound
(D) crude oil containing low percentage of sulphur.
241. Baryon is one of the class of heavy elementary particles that includes
(A) hyperons
(B) neutrons
(C) protons
(D) all of the above.
249. Barn
(A) spent fuel from a nuclear reactor
(B) a unit of area
(C) an electronic instrument for rapid counting of radiation
(D) a coal that does not form coke.
252. The phenomenon of physical adhesion of molecules to the surfaces of solids without chemical reaction is known as
(A) dredging
(B) coking
(C) absorption
(D) liquation.
253. Solid or liquid panicles of microscopic size which are suspended in air or another gas form what is known as
(A) aerosol
(B) hyperon
(C) geognosy
(D) eluvium.
260. In a boiler, the carry over of slugs of water into the piping due to dirty water is termed as
(A) beating
(B) foaming
(C) seal ping
(D) pitting.
265. Liquids lighter than water (such as petroleum oils) have APT gravities numerically
(A) less than 1.0
(B) greater than 1.0
(C) greater than 10
(D) around 100.
Contact Us : Mithilesh Singh (9827482029) Email : mithileshkhudawal@gmail.com
website link: http://mithileshkhudawal.wix.com/boeindia
IBCI is the Premier BOE Coaching Institution in Raipur (India),where dream convert into reality in very short
duration
IBCI (Indian BOE Coaching Institute)
Study material for BOE examination preparation
MCQ(Multiple choice question) on Power Plant Engineering :
266. All of the following arc hard coals Except
(A) Anthracite
(B) Lignite
(C) Bituminous
(D) Semi bituminous.
284. Perlite is
(A) a low ash containing coal
(B) same as lignite
(C) an insulation material
(D) none of the above.
290. For the same heat input and the same maximum pressure, the most efficient cycle is
(A) Brayton cycle (B) Otto cycle
(C) Diesel cycle (D) Dual cycle.
Note :1. Above mentioned BOLD marked option is right answer of the questions. 2.During preparation of this study
material very high level of attention being taken care but if you feel any abnormality let us know.