Professional Documents
Culture Documents
SEAMLESS TUBULARS
Edgen Murray has the largest stock of offshore quality Structural Seamless Tubulars anywhere in the
world. All is manufactured to the strictest quality controls and duly certified to the requirements as
specified by the most demanding of industries.
The material specifications as detailed above cover the entire list of specified sizes.
Other material specifications, diameter and wall thickness are available by arrangement.
In particular a large range of carbon specifications are available in OD range, 3.175mm - 660.4mm from our US Stocks.
Pipe lengths are generally double randoms.
To determine the weight of a seamless tubular, please use the following formula.
(OD-WT) x WT x 0.0246615 = kg per metre.
Edgen Murray Seamless material is manufactured to very strict technical requirements and is fully in accordance with Edgen Murray Proprietary
Specifications. Copies of these Proprietary Specifications are available upon request.
Modifications to these requirements are possible and should be discussed with us as necessary. Likewise alternative specifications can be supplied
through our close working relationships with all of the leading pipe mills in the world.
The principal properties of Edgen Murray stock material is as below and is listed for general information purposes only.
Precise information is available upon request.
CHEMICAL/MECHANICAL VALUES
Carbon 0.14% max
Sulphur 0.007% max
Phosphorous 0.025% max
Chromium 0.25% max
Titanium 0.02% max
Nickel 0.30% max
Aluminium Total 0.06% max
Nitrogen 0.014% max
Cr+Mo+Ni+Cu 0.80% max
Nb+V 0.10% max
Nb+V+Ti 0.12% max
CEV 0.43% max
Residual Element Analysis Reported as Ladle
Soluble & Total Aluminium to Nitrogen Ratio 2:1 minimum
PCM 0.25% max
Tensile (PWHT condition above 20mm wall) 460 - 620 n/mm2
Minimum Yield (up to and including 40mm wall ) 359 n/mm2
Minimum Yield (over 40mm up to 50.8mm wall ) 345 n/mm2
Impacts Longitudinal at minus 40 degrees C 50 joules average, 35 joules minimum individual
Impacts Transverse at minus 50 degrees C 50 joules average, 35 joules minimum individual
Supply Condition Normalised or quenched and tempered.
For all of your requirements and further information, please speak with your usual point of contact.
WELDED TUBULARS
FOR OFFSHORE APPLICATION
Edgen Murray are a world leader in the supply of Welded Tubulars for Offshore Application, produced in
accordance with international standards and suitable for structural application and/or down-hole
conductor usage. In addition to secured manufacturing capabilities with globally reputable steel mills
& manufacturers, Edgen Murray provide significant levels of stock product available from strategically
located stockholding facilities.
From an immediate ex stock basis the following are the principal sizes and grades held worldwide by Edgen Murray.
All pipes are produced to the latest editions of manufacturing specifications following requirements of PSL1 or PSL2 (where applicable).
Standard pipe lengths are supplied as 38 FT / 40FT (11.582 / 12.192 metre), supplied with beveled ends and protectors.
It is also possible to produce welded (SAW) tubulars in non-standard dimensions, short lead-time, unrestricted quantities by utilising
Edgen Murrays pre-existing plate stock and pre-booked mill capacities.
www.edgenmurray.com
WELDED TUBULARS FOR OFFSHORE APPLICATION Americas: +1.713.268.7200
APAC: +65.6223.3334
EMEA: +44.131.333.3333
To determine the weight of a welded tubular, please use the following formula.
(OD-WT) x WT x 0.0246615 = kg per metre.
As an example, a tubular with a 762.0 mm outside diameter and 25.40 mm wall thickness can be calculated as:
(762.0-25.4) x 25.4) x 0.0246615 = 461.4079 kg per metre
The following lists a range of weight factors by typical size as held in stock by Edgen Murray.
However, please be advised that this is by no means an exhaustive list of stock sizes and serves only as an indication.
For additional information or materila requirements, please contact one of our regional offices.
STRUCTURAL
PLATE
Edgen Murray is without question the market leader in offshore quality plate supply in the world.
The company collectively holds the largest available stock and range of offshore quality plate in
several locations around the globe.
DIMENSIONAL RANGE FOR
LOCATION SPECIFICATION
ALL SPECIFICATIONS
United Kingdom EN 10225 S355G3+N, S355G8+N, S355G10+M, S355G10+N 6mm - 100mm
BS 4360 1986 50DD
EN 10025 S355J2+AR, S355K2+N
DNV NVE36
BS 7191 1989 355D, 355EM
Holland EN 10225 S355G3+N, S355G10+M 10mm - 50mm
EN10225 S460G2+M / Norsok Y40 8mm - 80mm
Azerbaijan EN 10225 S355G3+N, S355G10+M 6mm - 45mm
DNV NVE36
United Arab Emirates EN 10025 S275JR, S355J2, S355K2 6mm - 150mm
ABS EH36
ASME SA 516 Grade 60, Grade 65, Grade 70
ASTM A516 Grade 65 HIC, Grade 70 HIC
API 2H Grade 50, API 2W Grade 50
ASTM A514 Grade F, ASTM A517 Grade Q
EN 10225 S355G8+N 6mm - 100mm
Saudi Arabia ASTM A516 Grade 60, Grade 65, Grade 70 6mm - 40mm
ASTM A516 Grade 65 HIC, Grade 70 HIC
Singapore API 2H Grade 50
API 2W Grade 50, Grade 60 8mm - 180mm
EN 10225 S355G10+M, S420G2+M
United States API 2H Grade 50, Grade 60
API 2W Grade 50, Grade 60
ASTM A 516 Grade 60, Grade 65, Grade 70
ABS AH36, DH36, EH36, EH40, FH40, EQ47, EQ56, FQ70
DNV NV D36, NV E36, NV F40, NV F500
ASTM A 572 Grade 50, Grade 60, Grade 65
ASTM A514 Grade B, Grade F, Grade H, Grade Q
ASTM A656 Grade 80
ASTM A710
EN 10225 S355G8+N, S420, S460 G2+M, S690
Speciality Steels AR400, AR500, Armor Plate
Caterpillar Approved Steels
Please note that where stock of API-2W/2H Grade 50/60 is available above 40mm thickness, the material is fully qualified to the requirements to API-RP2Z with CTODs.
All materials available with certification to EN 10204 Type 3.2.
www.edgenmurray.com
STRUCTURAL PLATE Americas: +1.713.268.7200
APAC: +65.6223.3334
EMEA: +44.131.333.3333
Plate is normally held in 6 metre, 10 metre or 12.2 metre lengths in widths of 2 metre, 2.5 metre
and 3.05 metre. An infinite length and width variety together with alternate material specification
options are also available through mill sources.
To calculate the weight of a reversing mill plate, the following formula should be applied:
Length (m) x Width (m) x Thickness (mm) x .0.00785 or 0.00800
The following is a selection of examples and are typical of Edgen Murray stock supply.
The use of either 7.85 or 8.00 kg per mm of thickness as the weight factor is dependent upon the mill of production and the material grade. On occa-
sion other weight factors may be applied. This is particularly the case with respect to Alloy Products such as Stainless
Steel and Nickel Alloys. Please always check with your normal point of contact.
Plates are supplied to the dimensional and flatness tolerances of the relevant product standard. Likewise material will be tested
in accordance with the relevant product standard.
Modifications to such standards are possible and this should be discussed with us as necessary.
Edgen Murray also has in place with the major plate mill manufacturers a fully comprehensive list of Proprietary Specifications to
facilitate ease of ordering. These specifications are based upon the principal National Standards applicable to Offshore Quality materials with appro-
priate and relevant modified enhancements. Copies of these Proprietary Specifications are available upon request.
For all of your requirements and further information, please speak with your usual point of contact.
STRUCTURAL SECTIONS
FOR OFFSHORE & ONSHORE APPLICATION
Edgen Murray is a leading supplier of structural sections for both offshore and onshore application
throughout the world. This is from either a direct stock supply route or a back-to-back mill route, or indeed
a combination of both. A full range of products and sizes is available through various extensive stocks in
UK Imperial, Euronorm, American and Australian dimensions.
STOCK LOCATION DIMENSIONAL DESIGNATION PRODUCTS
United Kingdom Imperial, Euronorm Beam, Column, Channel, Angle, Flats, Rounds, Squares
United Arab Emirates Imperial, Euronorm Beam, Column, Channel, Angle, Flats
Singapore Imperial, Australian Beam, Column
Azerbaijan Imperial, Euronorm Beam, Column, Channel, Angle, Flats
Holland Euronorm Beam, Column, Channel
The principal material specifications held by location are as follows. Additional Grades may also be available from stock and certainly through our mill
contacts. As always please refer your enquiries to your normal contact at all times.
Edgen Murray holds as stock the full dimensional range of each Dimensional Designation.
Please call us for full details of each individual size held. In addition, reference should also be made to the applicable standards for their size coverage.
However as a guide the following applies. Additional sizes are available through our mill routes of supply and again you should speak with your normal
contact for details.
Reference should be made to the appropriate Dimensional Designation Tables for individual weight factors.
For all of your requirements and further information, please speak with your usual point of contact.
STRUCTURAL
HOLLOW SECTION
Edgen Murray has the largest stock of Square and Rectangular Hollow Section for Offshore
Applications anywhere in the world.
All sizes will be supplied as an electric welded product with the exception of the following sizes.
150 x 150 x 16mm and 200 x 100 x 16.0mm shall be supplied as a seamless product.
400 x 400 x 20mm and 500 x 300 x 20.0mm shall be supplied as a submerged arc welded product.
For all of your requirements and further information, please speak with your usual point of contact.
CARBON
PRODUCTS
Seamless / DSAW / ERW / Intermediate Walls / Heavy Walls / High Yield X Grades
Our inventory is one of the most complete and comprehensive in the world.
CARBON PIPE
ASTM/ASME A/SA53 B 1/8 Nom OD - 26 OD
Seamless Pipe ASTM/ASME A/SA106 B, C 1/8 Nom OD - 26 OD
API 5L (PSL-1, PSL-2) B, X42, X52, X56, X60, X65 2 Nom - 26 OD
ASTM/ASME A/SA53 A, B 1/8 Nom OD - 26 OD
ASTM A252 2, 3 4 Nom - 24 OD
Welded Pipe - ERW
API 5L (PSL-1, PSL-2) B, X42, X52, X56, X60, X65, X70 2 Nom OD - 26 OD
Slurry Pipe / Abrasive Resistant 220, 240 Brinell 3 Nom - 24 OD
ASTM A252 2, 3 18 OD - 48 OD
ASTM A671 CC60, CC65, CC70 24 OD - 108 OD
Welded Pipe - DSAW ASTM A672 C60, C65, C70 24 OD - 108 OD
API 5L (PSL-1, PSL-2), API 2B B, X42, X52, X56, X60, X65, X70, X80 18 OD - 60 OD
CSA Z245.1 483 Cat 2 24 OD - 42 OD
AWWA C200 16 OD - 108 OD
Welded Pipe - Spiral ASTM A252 2, 3 16 OD - 108 OD
Slurry Pipe / Abrasive Resistant 220, 240 Brinell 30 OD - 48 OD
CARBON FITTINGS
ASTM A234 WPB 2 - 42
Butt Weld Fittings
MSS - SP - 75 Y42, Y52, Y60, Y65, Y70 4 - 42
ASTM A105 2 - 42
Flanges A694 F42, F52, F60, F65, F70 4 - 42
AWWA C207 CLASS 1 TABLE D 3 - 48
FEATURES
- Mill test reports to EN 10204 3.1 - Pipe and BW fittings triple certified ASTM/ASME UNS S32205/S31803, EN 10216-5 TC2 Grade
- Norsok certified 1.4462
- MESC certified - Flanges and forged fittings in accordance with ASTM/ASME/EN/SA F51, F60, 2205 and 1.4462
- Hardness to NACE MR 01-75 and NACE MR 01-03 - Corrosion tests to G48 A and E923 Methods A&C
- Charpy @ -50 deg C - Ferrite 40%-60% in accordance with ASTM E562 @ 500x
- Impact to A923 Method B - 100% PMI
ASTM A564 17-4PH UNS S17400 1 - 16 Dia Solution Treated Double Aged (DH1150)
ASTM A182 F51 UNS S31803 / S32205 0.5 - 15 Dia Solution Annealed
Duplex/Super Duplex ASTM A182 F53 UNS S32750 0.5 - 16 Dia Solution Annealed
ASTM A182 F55 UNS S32760 0.5 - 22 Dia Solution Annealed
Alloy 718 UNS N07718 0.5 - 15 Dia Solution Annealed Age Hardened
Alloy 625 UNS N06625 1 - 12 Dia Annealed Bar
Alloy 725 UNS N07725 1 - 10 Dia Solution Annealed Age Hardened
Nickel Alloy
Alloy 825 UNS N08825 1 - 12 Dia Annealed Bar
Alloy 925 UNS N09925 1 - 12 Dia Solution Annealed Age Hardened
Alloy K500 UNS N05500 1 - 12 Dia Hot Finished Age Hardened
SERVICES OFFERED
Forgings We offer specific open die forgings and seamless rings to simple and complex shapes over all material grades.
We can drill/bore IDs into existing stock material and rough machine standard and complex shapes prior to heat treating a
Machining
specific component using conventional and CNC lathes, milling equipment and deep hole boring machines.
All materials are Heat Treated differently. Heat Treatment options available are:
- Annealing - Age and Precipitation Hardening
- Ultrasonic Testing
- Magnetic Particle Inspection (MPI)
Non-Destructive Examination
- Dye Penetrant Inspection (DPI)
- Positive Material Identification (PMI)
CHROME MOLY, LOW TEMPERATURE,
CARBON STEEL & STAINLESS
Let us be your first step for chrome moly, stainless, low temperature.
LOW TEMPERATURE
Seamless Pipe ASTM/ASME A/SA 333 Grade 1, Grade 3, Grade 6 1/2 - 24
Welded Pipe ASTM/ASME A/SA 672 C60, C70 20 - 48
Butt Weld Fittings ASTM/ASME A/SA 420 WPL3, WPL6 1/2 - 24
Flanges ASTM/ASME A/SA 350 LF2, LF3 1/2 - 24; 150# - 2500#
Pressure Fittings ASTM/ASME A/SA 350 LF2 1/2 - 3; 3000# - 6000#
Cast Valves ASTM/ASME A/SA 352 LCC 2 - 24; 150# - 600#
Forged Valves ASTM/ASME A/SA 350 LF2 1/2 - 2; 800# - 1500#
STAINLESS
ASTM/ASME A/SA 312/376 TP304/L, TP316/L, TP304/H, 1/4 - 16
Seamless Pipe TP321/H, TP347/H
ASTM/ASME A/SA 790 UNS S31803/S32205 Duplex 1/2 - 8
Welded Pipe ASTM/ASME A/SA 790 UNS S31803/S32205 Duplex 1/2 - 12
ASTM/ASME A/SA 403 WP321/H, WP347/H 1/2 - 8; 10S, 40S, 80S
Butt Weld Fittings
ASTM/ASME A/SA 815 S31803/S32205 Duplex 1/2 - 12; 10S, 40S, 80S
Flanges ASTM/ASME A/SA 182 F321/H, F347/H, F51 Duplex 1/2 - 12; 150#, 300#
Pressure Fittings ASTM/ASME A/SA 182 F51 Duplex 1/2 - 2; 3000#
Forged Valves ASTM/ASME A/SA 182 316L, 347 1/2 - 2; 800# - 2500#
SEAMLESS STAINLESS
Grades: 304/H,304/L,316/L,321/H,347/H
Seamless Pipe ASTM A312 1/8 - 12 10S, 40S, 80S, 120, 160, XXH
Butt Weld Fittings ASTM A403 1/2 - 8 10S, 40S, 80S
Flanges ASTM A182 1/2 - 8 150#, 300
ABRASION
RESISTANT PIPE
Edgen Murray is the principal provider of Abrasion Resistant Pipe (Slurry Pipe) for the U.S. and Canada. With a minimum average brinell of 230,
the pipes highly durable composition is resistant to wear and abrasive materials, yet maintains ductility and workability in the field. That makes AR Pipe
the most cost-effective option for long-term use in dredging, various mining activities, power plants and other abrasive applications.
Edgen Murray is the primary stocking distributor in the country, maintaining a preferred relationship with American Steel Pipe, the nations preeminent AR
Pipe producer. American is also unique in their capability to produce and hydrostatically test lengths up to 100 ft., while international competitors only
offer up to 50 ft. lengths.
Edgen Murray surpasses other distributors in knowledge and experience, and offers considerable expertise in flanging services and welding in the field. Mill
test reports certifying chemical and physical properties are available on all AR pipe.
Physical Properties:
Elongation: Diameter:
- Minimum 20% - The diameter of no more than 1/32 smaller
or 3/32 larger than the tabulated outside diameter
for a distance of 4 from the end of the pipe.
Brinell Hardness:
- Minimum average 230 BHN
Weight:
- Each pipe joint shall not weigh less than 95%
Weld Flash: of its nominal weight.
- Maximum height of 1/8, with a minimum wall
thickness of 95% of nominal wall thickness.
Length:
- AR pipe is available in uniform lengths up to 100 ft.
Wall Thickness: with a length tolerance of plus or minus one inch.
- The average wall thickness of all pipe combined
on a given rolling shall not be less than the
nominal wall thickness.
BALL VALVES GATES, GLOBES & CHECKS BUTTERFLY VALVES ACTUATION PACKAGES LONG WELD NECK FLANGES
W-K-M BONNEY FORGED STEEL VALVES - W-K-M ROTORK FCI FORGED COMPONENTS
FORGED/CAST STEEL/ALLOY
CAMERON STOCKHAM BETTIS
ORBIT KINKA
APOLLO WALWORTH
PLUG VALVES API-6-D CHECK VALVES NEEDLE VALVES BLEEDER PLUGS MANUAL ACTUATION ACCESSORIES
NORDSTROM CROWN CHECK VALVES- ANDERSON GREENWOOD PLEECO BABBITT SPROCKET RIMS
DIVISION OF STREAM-FLO