Professional Documents
Culture Documents
Features
Part A B C D E F
Style.
Number Max. Max. 0.6 Max. Typ. Min.
BK130-100 8.3 10.7 5.1 3.8 0.5 7.6 DZ
BK130-120 8.3 10.7 5.1 3.8 0.5 7.6 DZ
BK130-160 8.5 12.5 5.1 3.8 0.5 7.6 DZ
BK130-200 9.6 17.4 5.1 3.8 0.6 7.6 SZ
BK130-250 9.6 17.4 5.1 3.8 0.6 7.6 SZ
BK130-300 9.6 17.5 5.1 3.8 0.6 7.6 SZ
BK130-400 11.4 19.5 5.1 3.8 0.6 7.6 SZ
BK130-500 11.5 21.7 5.1 3.8 0.6 7.6 SZ
BK130-650 14.0 21.7 5.1 3.8 0.8 7.6 SZ
BK130-750 14.0 21.7 5.1 3.8 0.8 7.6 SZ
BK130-900 14.0 21.7 5.1 3.8 0.8 7.6 SZ
BK130-1100 14.0 16.2 5.1 3.8 0.8 7.6 DZ
BK130-1350 18.0 25.0 5.1 3.8 0.8 7.6 SZ
Revision05-Jun-15 www.brightking.com
BK130 SERIES
Electrical Characteristics
Revision05-Jun-15 www.brightking.com
BK130 SERIES
Typical Time-to-Trip Charts @25
Storage Recommendations
Items Conditions
Refer to the condition recommended by the flux manufacturer.
Pre-Heating Zone
Maximum ramping rate should not exceed 4/sec.
Soldering Zone Maximum solder temperature should not exceed 260
Cooling Zone Forced cooling
Revision05-Jun-15 www.brightking.com
BK130 SERIES
Manual Soldering Recommendation Parameters
Items Conditions
The highest power of the manual soldering iron should be 30W or less, soldering
Soldering condition
temperature should not be higher than 280.
The soldering time should be kept within 3 seconds, otherwise it might cause
Soldering time
insulation layer cracking, and increased part resistance.
The distance on the leads between the soldering point and bottom of the PPTC
Soldering position
body should be equal or greater than 4mm.
The soldering iron should not contact the PPTC body except the leads. If the
Other soldering conditions are kept to lower temperature, less time and larger distance,
the outcome of the soldering will be better.
Notes: 1. Before using the device must be stored in the original bags, if the storage conditions do not guarantee,
the device may not be able to meet the given value.
2. The devices cant used for reflow soldering.
Mechanical Characteristics
Reliability Test
Damp heat, No visible damage, Electrical OK, 402, 90~95 % RH, total 48Hrs, after 4Hrs
steady state R/R020% test electrical parameter
Revision05-Jun-15 www.brightking.com
BK130 SERIES
Packaging
BK130-100
BK130-120
BK130-250
BK130-300 150200
Inner Box BK130-400
BK130-500 120150
BK130-650
500pcs/bag
BK130-750
2000pcs/box
BK130-900
150200
BK130-1100
BK130-1350
Revision05-Jun-15 www.brightking.com