You are on page 1of 44

FIRST Company: Calibration and Validation Services

FIRST Company is an industry leader providing Calibration, validation,


compliance and technical services to the pharmaceutical, biotechnology, medical
device, Petroleum and related industries. Our clients business needs and issues are
our primary focus. Client speed to market, aggressive deadlines, and a challenging
and changing regulatory environment are factors that experienced FIRST personnel
can assist your organization with in meeting and realizing its competitive
advantage.

Calibration (Metrology Laboratory):

FIRST Metrology Laboratory provides a rapid, cost-effective calibration services


with documentation of As Found & As Left data (unless otherwise requested).

Advantages of our Metrology Laboratory services include:

- Fast Turnaround.
- Rush Service: 1, 2, or 3-day Rush Service by Request.
- Monthly Notification of Calibrations Due.
- Detailed Documentation for Each Calibration.
- Customized Calibrations at Customer Request.

Temperature: Pressure:
Dry Block Calibrators. Process Gages.
Ovens & Environmental Chambers. Pressure Transducers.
Temperature Indicators. Pressure Switches.
Temperature Controller. Pressure Calibrators.
Thermocouples. Vacuum Gages.
Simulators. Vacuum Transducers.
Transmitters. Manometers.
Thermometers. Data Loggers.
Data Loggers. Vacuum devices.
Process Calibrators. Process Calibrators
Humidity: Electronic:
Data Loggers Multimeters
Hygrometers Process Calibrators

Mechanical Dimensional: Misc:

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Tachometers Timers
Torque Wrenches Stop Watches
Micrometers Gases Devices
Calipers
Height Gages
Dial Gages
Gage Blocks

Validation Services:

1- Equipment Validation Services.


2- Utility Systems Validation.
3- Facility Qualification.
4- Clean Zones Qualification.

1 - Equipment validation services:

Our validation scope includes: Sterilization equipments, sterilizing tunnel and sterile
filling systems Freeze-dryer and other pharmaceutical equipments.

2 - Utility Systems Validation:

- HVAC Systems. - Clean In Place Systems.


- Purified Water Systems. - Steam In Place Systems.
- WFI Water Systems. - Special Gases Systems.
- Clean Steam Systems.
3 - Facility Qualification:

- Installation Qualification (IQ).


- Operational Qualification (OQ) and, as appropriate Performance Qualification
(PQ) Protocols.
- A master plan will be prepared for each new facility. An IQ and OQ will be
prepared for all services and equipment.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
FIRST COMPANY: ENVIRONMENTAL SERVICES

FIRST has a significant track record and has proven its competence in the Egyptian
environmental services market. The firm has acquired substantial experience in different
environmental fields and has achieved unparalleled comprehension of the development of
environmental management in Egypt.
- Environmental Measurements and Monitoring
- Environmental impact assessment
- Hazardous waste management
- Solid Wastes Management

1- ENVIRONMENTAL MEASUREMENTS AND MONITORING


FIRST Company has the capabilities for all the environmental measurements related to
industrial and service sectors including the following measurements:
- Work Environment pollutants and gases survey
- Ambient Air Monitoring (Continuous Air Monitoring)
- Noise Intensity, Noise Dose and Octave Band Survey
- Illumination intensity measurements
- Vibration , Heat stress measurements
- Industrial Stack Emissions and particulates measurements
- Exhaust emissions measurements
- Volatile Organic Compounds measurements
- Earthing Resistance Measurements
- Thermal Mapping
- Respiratory and Total Suspended Particulates measurements (TSP, PM10, PM7,
PM5, PM2.5, PM1)
- Asbestos Survey

2- ENVIRONMENTAL IMPACT ASSESSMENT


At FIRST, we believe that the EIA is a process geared towards environmental
management and sustainability of the development through providing the basis for
decision-making. Our approach depends on prevention rather than mitigation.

3- WASTE MANAGEMENT
FIRST is active in the field of waste management with a focus on hazardous waste. FIRST
has accumulated an experience unparalleled in Egypt in the different aspects of hazardous
waste management which allowed the provision of high quality consultancy services to
both regulators and generators. Assignments undertaken by the firm have addressed
different aspects of the Hazardous Waste Management System, namely development of
system components, institutional development, development of guidelines, capacity
building as well as supporting

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
industrial facilities in implementing hazardous waste management practices. Targets for
our activities are equally diverse, encompassing hazardous waste regulators, bodies
involved in hazardous waste management operations, and hazardous waste generators with
an emphasis on the industrial sector.
FIRST team has been involved in assignments addressing almost all components of
hazardous waste management system through the development of guidelines, procedures
or training including classification of hazardous wastes, transportation, storage, permitting,
on-site management as well as hazardous waste treatment and disposal. Along these
assignments, FIRST team has had ample opportunity for continuous involvement in, and
contribution to, evolving hazardous waste management issues as well as provide quality
services to generators. Such multilateral involvement in the hazardous waste management
system has allowed the firm to enrich the development of the system through useful
feedback regarding the practicality of related regulations and requirements.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
FIRST Company

(INSPECTION AND LIFTING DIVISION)

1- Conventional Inspection Services

FIRST COMPANY has been carrying our


conventional inspection services in Egypt for more
than 10 years and has an experienced team consisting
of qualified inspectors to undertake this work. We
have used the latest techniques to build on our success,
enabling us to provide our clients with a safer, quicker
and reliable service.Through our work we have the
knowledge, expertise and experience to perform
conventional NDE inspections from our offices and
project network.Our conventional services include:
NDE/NDT Inspections, Liquid Penetrant, Magnetic Particle, Radiographic, Ultrasonic,
Visual Inspection, Electromagnetic Testing, Remote Visual Inspection and Quality
Assurance.

1.1 Liquid Penetrant (LP)

FIRST COMPANY utilizes Liquid Penetrant


inspection to detect surface discontinuities in both
ferromagnetic and non-ferromagnetic materials. In
castings and forgings, these may be cracks or leaks
in new products or fatigue cracks in in-service
components.

Testing is performed using visible red dyes under


visible light conditions or fluorescent dyes under
ultraviolet light. As the name implies, the dyes
penetrate into the surface discontinuities by capillary action.After the excess material is
removed from the material being tested, indications will appear. Evaluation and
classification of material is based on code or customer requirements.

1.2 Magnetic Particle Inspection (MPI)

MPI detects surface and near-surface imperfections such as


cracks, seams and laps in ferromagnetic materials, and is used
to assess location, size, shape and extent of these
imperfections.When the test object is magnetized, flaws
perpendicular to the magnetic field direction cause flux
leakage.Magnetic particles applied to the surface are held at

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
the location of the imperfection by flux leakage. In this magnetic particle testing technique,
dry particles are dusted onto the surface of the test object as the item is magnetized.

Dry particle inspection is well suited for the inspections conducted on rough surfaces. When
an electromagnetic yoke is used, the AC or half wave DC
current creates a pulsating magnetic field that provides
mobility to the powder.

The primary applications for dry powders are unground welds


and rough as-cast surfaces.

Dry particle inspection is also used to detect shallow


subsurface cracks. Dry particles with half wave DC is the best approach when inspecting
for lack of root penetration in welds of thin materials.

Half wave DC with prods and dry particles is commonly used when inspecting large
castings for hot tears and cracks.

1.3 Radiographic Testing (RT)

Conventional Radiography (RT) is a nondestructive


examination method that uses X-ray and Gamma ray for
detecting internal imperfections, for measuring wall thickness
and for detection of corrosion. With RT, the material is exposed
to a homogenous ray from a radioactive isotope or an X-ray
tube while a negative film is positioned behind the material to
be examined.After development of the film, thickness and
density differences (material imperfections) will show as blackness differences.Acceptance
criteria define whether or not the indication is non-acceptable (a defect) or not.FIRST
COMPANY licensed technicians and equipment meet all the ROK
radiography regulations.

FIRST COMPANY pipeline inspection capability benefits from


decades of experience in the pipeline industry. Our procedures
meet standard inspection specifications for Workmanship
Acceptance Criteria or Alternative Acceptance.We ensure that
welding repairs are kept to a minimum by providing welders with
quick and accurate process control feedback derived from our inspection data.

1.4 Radiographic Testing (Close Proximity)

Conventional Radiography is a nondestructive examination method


that uses X-ray and Gamma ray for detecting internal imperfections.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
FIRST COMPANY introduced Close Proximity Radiography to
Egypt in early 2006. Radiography provides a quality, cost
effective, permanent record with high volume capabilities due to
simple operation and portability. However, its use is restricted by
the inherent risks associated with the use of radiation and the need
to establish and manage a controlled area during the process. The
associated problems are greatly reduced by the use of the Small
Controlled Area Radiography (SCAR) system. SCAR has set the precedent for safer
working in the industry.

1.5 Ultrasonic Testing

FIRST COMPANY Provides Manual


(Conventional) Ultrasonic Testing and Automated
Ultrasonic Testing. Both techniques transmit
ultrasound through a material and receive the
reflected echoes from the back wall or from any
defects.

This makes it possible to locate discontinuities in a


material or weld. During Manual Ultrasonic Testing
the operator measures the material thickness by
reading from the screen.UT uses high frequency ultrasonic waves to detect surface breaking
and internal imperfections, measures material thickness and determines acceptance or
rejection of a test object based on a reference code or standard.Our UT techniques provide
instant results, and are sensitive to both surface and subsurface discontinuities throughout
the material. UT is capable of detecting imperfections throughout the entire material
thickness, and may be used with access to only one surface.

1.6 Positive Material Identification

FIRST COMPANYs Positive Material Identification (PMI)


quickly and accurately identifies the composition of more than
100 different engineering alloys onsite.FIRST COMPANY can
perform PMI on virtually any size or shape of pipe, plate, weld,
welding materials, machined parts or castings. Team performs
both x-ray fluorescence (XRF) and Spark Emission
Spectrography (SES), two methods of conducting a PMI
examination.

Both methods ensure compliance with Process Safety Management (PSM) requirements.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
1.7 Quality Control

NDT Service provides a comprehensive Egypt i Vendor


Inspection, QA/QC and expediting service for all types of
mechanical, rotating, electrical and electronic equipment as
well as Oil Country Tubular Goods (OCTG).

Services include:

Expediting
New Build Equipment Inspection
Surveillance
Temporary and Portable Equipment
Vendor Audits (Prior to PO Award)

QA inspection of equipment being fabricated repaired and/or refurbished in a vendors


facility. The equipment can be for upstream application or from a clients facility for a
capital project as well as maintenance repairs or replacement of
original equipment.No matter what the requirements of your
project are, we can provide qualified inspection personnel to
assure those requirements are met.FIRST COMPANY inspectors
are qualified and/or hold certifications through API, AWS, DOT,
NACE, NEMA or ASNT. The inspection activities are guided by
the companys Quality Manuals and ITP plans that are developed
and managed by FIRST COMPANY Quality Program
Management.

1.8 Remote Visual Inspection

Visual Inspection (VI) is one of the most widely used Non-


Destructive Testing (NDT) methods for the detection of
discontinuities before they develop into major problems. Areas
where visual inspection can be utilized are; poor welding,
corrosion and pitting, general condition monitoring, surface

degradation & defects and protective coating monitoring.

Visual Inspection means the inspection of equipment, structures


or vessels using a combination of the following human senses;
vision, hearing and touch. Visual Inspection often works in
conjunction with a number of the following NDT methods; UT,
EC, MT, PT or RT.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Visual Inspection can also be carried out with the aid of devices such as a magnifying glass,
flash lights, borescopes, digital video borescopes and camera systems to provide Remote
Visual Inspection (RVI).

FIRST COMPANY highly trained inspectors employ robotics, fiber optic cameras,
borescopes and other instrumentation and recording systems to conduct RVI on equipment
such as piping systems, vessels, turbines, boilers and heat exchangers.Data can be recorded
onto various storage media for viewing and storage.

2- Lifting Inspection:
Skilled, Certified Inspector and Hi-Tech Equipment at inspection field allow FIRST
Company to offer the Lifting inspection services with very high quality:
Lifting& Handling Equipment's Inspection
General Crane Inspection
Mobile Crane Inspection
Tower Crane Inspection
Fork Lift Inspection
Tank Inspection.

3- Advanced Inspection Services

FIRST COMPANY is at the forefront of providing Advanced Inspection Services to our


clients and we have been instrumental in bringing new worldwide inspection techniques
into Egypt .Through our work we have the knowledge, expertise and experience to perform
advanced NDT inspections from our offices and project network.Our comprehensive
service includes a variety of techniques:

Guided Wave
Time of Flight Diffraction (ToFD) and Phased Array (PA)
Positive Material Identification (PMI)
Magnetic Flux Leakage (MFL)
ACFM
Leak Testing
Thermography
Electromagnetic Testing (ET)
RFEC
IRIS
Digital Radiography
RVI and
Endoscopy Inspections.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
3.1 Internal Rotary Inspection System

FIRST COMPANY has the knowledge, expertise and experience


to perform inspections using a range of systems to inspect tubes
in Heat Exchangers, Air Coolers, Feed Water Heaters,
Condensers and similar items.This allows tubes to be inspected
periodically to detect and size discontinuities e.g. pits, erosion,
cuts, grooves, and wear. Correct technique selection is critical
and depends on the tube material, ferromagnetic or non-
ferromagnetic and the type of discontinuities expected.

Techniques include:

Internal Rotary Inspection System (IRIS)


Eddy Current Testing (ET)
Remote Field Testing (RFT)

Eddy Current Testing, and Remote Field Testing are


electromagnetic techniques and tend to be used as screening
tools in order to select tubes for IRIS, especially in the case of
ferromagnetic materials e.g., Carbon Steels.

3.2 Long Range Guided Ultrasonic

FIRST COMPANY uses the state of the art Wavemaker (4)


which generates waves propagating long distances, even
beneath a layer of insulation. The ultrasound is transmitted
and received from one single location.The response from the
metal loss feature is a function of the depth and
circumferential extent of the metal loss.

Guided Wave tools are available in fixed ring and modular


ring format. The fixed ring designs are suitable for pipe
diameters up to 8-inches. For larger diameters, a modular
ring up to 42-inches has been adopted. Guided Wave
inspections help you to limit follow-up inspection and
maintenance to the areas of real interest where the piping
was found to be defective.

3.3 Ultrasonic Phased Array

FIRST COMPANY uses the state of the art OmniScan MX

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Mainframe with Phased Array TOFD Acquisition Modules, combined with multipurpose
scanners and modulators.

Phased Array (PA) provides sharper detection capability for off-angle cracks, and is capable
of displaying multiple presentations simultaneously. PA applies computer-controlled
excitation to individual elements in a multi-element probe. It is an advanced pulse-echo
technique that utilizes multiple miniaturized transducers and time-delays to shape the
ultrasonic sound beam to a desired angle and focus. The versatility of the system permits
simultaneous views of different presentations, such as sectoral views as well as A-Scan, B-
Scan and C-Scan representations.

When compared with manual pulse-echo techniques, the


advantages of Phased Array testing are its excellent repeatability,
increased inspection speed, more accurate results. Moreover, PA
allows the digital storage of all data, location and system settings,
and is very much safer to operate within a working environment,
compared with Non-Destructive Testing methods that use X-rays
and gamma rays for detecting imperfections

3.4 Automated Ultrasonic Inspection

FIRST COMPANY has the knowledge, expertise and experience


to perform Phased Array and automated ultrasonic (AUT) on
both onshore and offshore operations. We use different
technologies from several manufacturers to provide complete
automated inspection capabilities. FIRST COMPANYs AUT
capability has been used on a variety of projects and for
numerous clients. Pipe sizes inspected have ranged from 5 to
48, wall thickness from 12mm to 33mm and to a variety.AUT uses conventional and
specialized transducers to introduce sound in the test materials. These transducers are
mounted to automated robotic crawlers, which articulate to cover large areas of the vessel
or piping surface. The data collected is then displayed in color in multiple A-Scan, B-Scan,
C-Scan and D-Scan images.
A-scan representation is the view in which the signal amplitude
is shown as a vertical excursion from the horizontal sweep time
trace.The B-scan and D-scan presentations are two-dimensional
views of cross-sectional planes through the test object on
different axis. This imaging is helpful in distinguishing mid-wall
inclusions such as laminations and blistering, from back-wall
discontinuities like erosion and corrosion.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
The C-scan image is a two-dimensional plan view of the object. Indication of depth is color
coded to provide the image with qualities, which resemble a
topographical map viewed from the inspecting surface.

3.5 Magnetic Flux Leakage

FIRST COMPANY has the knowledge, expertise and


experience to perform Magnetic Flux Leakage (MFL) on tanks.

We use the MFL 2000 which is a high speed, motorized


magnetic flux leakage corrosion detection scanner capable of
inspecting approximately 8000 square feet per shift.The
ergonomic design, coupled with the latest magnetic technology
have resulted in an easy to operate, accurate, reliable and cost
effective inspection tool.The motorized scanner takes all the
strain giving you more consistent results and less operator
dependency.

Key Features High Speed, Cost Effective Inspection

Easy to Use Ergonomic Design


Automatic Defect Detection System
Minimal Maintenance Requirement

The MFL 2000 corrosion detection floor scanner from Silverwing is a combination of
magnetic technology and customer led ergonomic mechanical design. The system is
designed specifically with the operator in mind and the availability of a new consistent high
quality magnetic material has allowed a complete redesign of the MFL 2000. In addition the
new mechanical design has overcome some of the more difficult and time consuming set-up
procedures and also eliminated the vulnerable cabling, so reducing maintenance costs.

3.6 Time of Flight Diffraction

FIRST COMPANY uses the state of the art OmniScan MX 2


Mainframe with Phased Array ToFD Acquisition Modules,
combined with multipurpose scanners and modulators.

With ToFD, a single line scan of a pair of angle compression


wave probes held at a fixed separation can provide full
volumetric coverage of both weld and heat affected zone
(HAZ) and generate an immediate scale image of through wall
condition with defects shown in true location and size. The
wide beam used defines the test surface by generating a lateral
wave and the inner surface by reflections off the material

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
backwall. Any anomalies lying between these two surfaces are highlighted by signals
diffracted and reflected off their extremities. The lateral location and length of these
discontinuities is reported as a function of encoded scan position.(ToFD), which was
originally developed for crack-sizing in nuclear applications, established itself as a widely
used tool for flaws detection in welds. This unique ultrasonic technique has big advantages
in speed, detection of defects and is the most accurate defect sizing technique in general
use. One of the important advantages of using ToFD for weld inspection is the absence of
radiation. Furthermore, in several validation projects ToFD has proved itself to be a
technique which combines a high detection rate with a very high reliability in pre-service
and in-service inspections.

3.7 Automated Corrosion Mapping

CONDITION MONITORING

Corrosion and erosion monitoring

Corrosion and erosion mapping utilizing Automated system and a Combination of


ToFD, Phased Array and Pulse Echo
Ultrasonic imaging
Detection, imaging and monitoring of material degradation
Defect sizing and propagation monitoring
Real time Inspection

Sample Corrosion Map Petrochemical Plant Process Pressure Vessel (1)

Sample Corrosion Map Petrochemical Plant Process Pressure Vessel (2)

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Sample Corrosion Map

Low and High Temperature Hydrogen Attack Detection

Products & Services

High Temperature Hydrogen Attack

Advanced Backscatter Techniques

Low Temperature Hydrogen Attack

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Low Temperature Hydrogen Attack

Low Temperature Hydrogen Attack On HP Separator in H2S Service

Low Temperature Hydrogen Attack

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
3.8 Stress Corrosion Cracking

FIRST COMPANY utilizes the Time of Flight Diffraction method for detection of Stress
Corrosion Cracking.

3.9 Long Range CHIME Inspection

Long range ultrasonic Chime

Under clamp/pipe support corrosion


Corrosion under annular plate

Guided wave ultrasonic

Buried pipelines

Long Range Chime

Corrosion Under Supports (CHIME)

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Corrosion Under Supports (CHIME)

Key Features of the System

Large areas can be inspected with a single pass


Estimate of the extent of corrosion attack
The full volume can be inspected with probes separated by up to 1 meter
Sensitive to both internal and external surfaces
Suitable for pipe diameters 75 mm and above
Suitable for inaccessible locations such as clamps, saddles, tank floors and half-
buried pipes.

3.10 Eddy Current Testing

FIRST COMPANY, by utilizing Eddy Current


techniques, can examine large areas very quickly
and it does not require the use of coupling liquids.

In addition to finding cracks, EC can also be used to


check metal hardness and conductivity in
applications where those properties are of interest
and to measure thin layers of nonconductive
coatings like paint on metal parts.

Applications

Surface Breaking Cracks


SBC using Sliding Probes
Metal Thinning (Corrosion)

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Heat Exchanger Tube Inspection
Conductivity
Heat Treat Verification
Thickness inspection of Thin Materials
Thickness inspection of Coatings

3.11 Boiler Inspection

FIRST COMPANY utilizes EMAT technology to perform boiler


tube inspection without scale removal.Scale is used as a couplant
to transfer electromagnetic signal into boiler tube for thickness
detection.Utilizing this method saves time as tube cleaning is not
required, therefore reducing boiler downtime.

3.12 Digital Radiography

Digital Radiography is a powerful technique that can be used in


nondestructive inspection of internal features of an object to
obtain two-dimensional computed tomography images needed to
characterize material properties, identify defects and measure part
geometry.

Multiple slices can also be assembled to create accurate three-


dimensional CT that can be used for a variety of different purposes
as viewing the shape of defects.FIRST COMPANY can provide
site inspection utilizing method above for all your needs and
requirements.

4- Pipeline Inspection Services

FIRST COMPANY provides a complete range of services for your pipeline inspection
needs.

This includes:

X RayCrawer Inspection
Gamma Ray Inspection
Advanced Ultrasonic Inspection (Combination of Phased Array, Time of Flight
Diffraction and Shear wave Ultrasonics)
Long Range Ultrasonic Inspection
Advanced Corrosion Mapping
Intelligent Pigging (Ultrasonic and MFL methods)

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
4.1 X-Ray Pipeline Inspection

FIRST COMPANY has the knowledge, capability and


experience to provide Conventional X-Ray and Gamma
Ray inspection on pipelines as well as X-Ray crawler
inspection on pipes from 10 to 48 diameters.

4.2 Automated Pipeline Inspection

FIRST COMPANY has the knowledge, expertise and


experience to perform Phased Array and automated
ultrasonic (AUT) on both onshore and offshore operations.
We use different technologies from several manufacturers to
provide complete automated inspection capabilities. FIRST
COMPANYs AUT capability has been used on a variety of
projects and for numerous clients. Pipe sizes inspected have
ranged from 5 to 48, wall thickness from 12mm to 33mm
and to a variety.

AUT uses conventional and specialized transducers to introduce sound in the test materials.
These transducers are mounted to automated robotic crawlers, which articulate to cover
large areas of the vessel or piping surface. The data collected is then displayed in color in
multiple A-Scan, B-Scan, C-Scan and D-Scan images.A-scan representation is the view in
which the signal amplitude is shown as a vertical excursion from the horizontal sweep time
trace.The B-scan and D-scan presentations are
two-dimensional views of cross-sectional planes
through the test object on different axis. This
imaging is helpful in distinguishing mid-wall
inclusions such as laminations and blistering,
from back-wall discontinuities like erosion and
corrosion.The C-scan image is a two-dimensional
plan view of the object. Indication of depth is
color coded to provide the image with qualities,
which resemble a topographical map viewed

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
from the inspecting surface.

4.3 Intelligent Pigging

FIRST COMPANY provides inspection utilizing intelligent pigging ILI and MFL for
corrosion detection and cracking.The ILI system can also be used for riser inspections, with
or without production outage. Large diameter piping from 4 up to 64 metallic and non-
metallic pipelines can be inspected. This method of inspection is fast end extremely
accurate with immediate inspection results.MFL can
be used with or without liquid in the pipeline and
offer a higher inspection speed and hence greater
rangeThese MFL tools are based on the latest
standards of electronics, data processing and
measuring principles. This has led to a unique set of
features such as:Real tri-axial measurement of the
flux leakage vector, resulting in accurate assessment
of metal loss.Flexible tools with high tolerance for
various pipeline diameters, wall thicknesses and bend
radii.

5. Heat Treatment Services

FIRST COMPANY and our alliance partner


DenholmZholdas are the largest provider of Heat
Treatment services in Egypt having over (8000)
KVA of available heat treatment power sources and
High Velocity Fuel Fired Heat Treatment
Services.We have a range of high velocity burners
diesel oil for the in-situ heat treatment of large
fabrications, Welding Preheats, Post weld heat
treatments, Hydrogen bake-outs, Temporary
Furnaces, Dry-outs, Equipment sales/rentals and Equipment
calibration and service

5.1 Electrical Resistance

The traditional low-voltage Electrical Resistance method of


heat treatment uses ceramic blankets stepped down to 80 volts
to provide a quick and convenient approach to many jobs,
particularly preheat and Post-weld Heat Treatment (PWHT).

5.2 Welding Preheat

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
Advanced automated systems control and document welding preheat to reduce thermal
stress in two primary ways. First, it drives off moisture that would release hydrogen that
could penetrate the steel and cause porosity and subsequent cracking. Second, it reduces
heat loss to the surrounding metal, minimizing the rate of weld hardening and allowing
hydrogen that is present to escape.

5.3 Post-weld Heat Treatment

Carefully controlled PWHT is a crucial step in maximizing the life of your process
equipment. PWHT tempers the metal and reduces tensile stresses, minimizing the risk of
brittle fracture, stress, corrosion cracking and metal fatigue. This is especially important for
equipment used in harsh service environments.

5.4 Combustion Heat Treatment

FIRST COMPANY has burners that will deliver an astonishing


100 million BTUs.In addition to multiple safety interlocks and
redundancies, these systems feature a turndown ratio of 100:1,
which allows FIRST COMPANY to vary heat output from
candle intensity to full blast in increments as small as 1F/hour.
Output from 20HP blowers varies from 500 CFH to 168,000 CFH to ensure that heat is
distributed evenly regardless of a vessels geometryFIRST COMPANY Combustion Heat
Treating method may be used in a variety of applications including Post-weld Heat
Treatment, Refractory Dry Out and Process Startup.Post-weld Heat Treatment: Carefully
controlled post-weld heat treatment.

Refractory Dry Out: The secret to long refractory life is a professional Dry out using FIRST
COMPANYs high-velocity combustion systems to ensure that every inch of your
refractory is heated under control as tight as one degree per hour.

Process Startup: It is well known that process heaters are


designed for a small range of temperatures. FIRST
COMPANYs high-velocity combustion systems feature
exceptional turndown ratios (100:1), so they can be
programmed to increase from candle-heat to process heat in
tightly controlled increments. It is the best way to minimize
thermal stress and ensure long run-times in cyclone boilers,
CFBs, steel mills, glass plants and other process applications.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
FIRST Training
FIRST Training Academy provides

FIRST Training Academy is a highly professional Academy providing QHSE and Technical
training and consultation.
Main Office: 61 East Autostrad Buildings, Sakr Korish, Maadi, Cairo.
E-mail: training@first-env.com , first-env@hotmail.com
Why We Are Different?
- Our target is client satisfaction.
- We apply the updated HSE International standards.
- We strive to provide the optimum, most economical / best technical solution to your
concern.
- Our staff has a long field and true hand on experience.
- We ensure that our deliverables meet your expectations.
- We work hard with all to ensure that our services are tailored and specific to all
operations and needs.
Center Activities
FIRST Training Academy Provides technical and engineering consultations, training, auditing,
upgrading management system to meet the requirements of the international standards and other
oil services.
FIRST Academy Organizational Structure
FIRST Academy organizational framework is based on administrative, technical, scientific
elements and methods, whereby a dynamic, smooth and complementary performance is ensured.
Organizational Frame Work
- Technical Department
- Training Department
- Marketing Department
- Finance & Administration Department
FIRST Academy Training Activities
- ISO 9001, 14001, OHSAS 18001 Internal Auditor
- ISO 9001, 14001, OHSAS 18001 Lead Auditor
- API Spec Q1 Training and Consultation
- API Spec Q2 Training and Consultation
- OSHA ( Occupational Safety & Health Administration )
- (General / Construction / Disaster Site Work)
- OHSAR ( Occupational Health & Safety At Rigs )
- IOSH
- LPGS ( Liquefied Petroleum Gas Safety )
- Risk Management
- HSE Management System
- HSE Management System Auditing & Site Inspection
- Emergency Preparedness
- Basic & Advanced Fire Fighting
- Management of Contractors HSE Management System
- Job Safety Analysis

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
- HSE Induction &Awareness
- Project HSE Management
- H2S Emergency Plan
- Risk Analysis
- Safety in Construction Field
- Confined Space Entry
- Crisis Management
- Accident Reporting, Investigation ,Analysis and Follow up
- OHSAS 18001& ISO 14001
- Occupational Health Risk Assessment
- Critical Safety Equipment
- Behavioral Based Safety
- Project HSE Plans
- Project HSE Philosophy
- Area Classification
- Office Safety
Training Courses Related to the Business Process Improvement
- Professional Selling Skills
- Management Planning & Follow up
- First Time Manager
- Communication Skills
- Human Resources Management
- Project Management
- Benchmarking
Companys Safety Technology
- Designing, Reviewing and Testing of Fire Fighting and Protection Systems.
- Development of HSE Management systems as required.
- Fire Fighting Training (Basic/ advanced).
- First Aid Training (Basic / Advanced).
- Preparation of the Risk Assessment & Safety case Studies.
- Preparation of the Emergency & evacuation plans and training on the emergency drills.
- Preparing HSE Records
- Safety inspection for all high risk equipments e.g. Boilers, High pressure pumps, electric
transformers, Electrical panelsetc.
- Preparation of Safety Manuals for all activities
- Providing the best Personnel Protection Equipments ( PPE)( e.g. Boots, gloves, overalls,
SCBA,.etc)
- Providing the fire fighting equipments & materials.
- Maintenance of the fixed & mobile fire fighting equipments.
- Preparation of Safety Checklists for all hazardous equipments such as Cranes, Boilers,
Pumps, vehicles, compressors, electrical panels and transformersetc.
- HSE auditing of all assets, companies and systems.
- Drilling and work over rigs HSE-inspections.

FIRST Training Academy Environment Activity


- Environmental Management system implementation
- Environmental Management Auditing
- Environmental Policies and Planning
- ISO 14001 preparation and maintaining
24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt
Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
- Environmental Impact Assessment
- Environmental Reporting
- Ambient Air Quality Assessment
- Indoor Air Quality survey
- Water Quality Assessment
- Waste Management and Audit
- Documentation of Environmental Activities
- Environmental Training
Methods of Contracting
We are ready to provide our services in any of the following contracting methods:
1) Permanent contract through providing professional staff within the organization.
2) Permanent contract through frequent visits (monthly, quarterly, bi-annul, annually).
3) Temporary contract for a certain period of time.
4) On call request.

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
FIRST COMPANY: Water Quality Testing and Analysis Laboratory
FIRST has a significant track record and has proven its competence inthe Egyptian
environmental and Water Testing services market. The firm has acquiredsubstantial
experience in different environmental and water analysis fields and has
achievedunparalleled comprehension of the development of environmentalmanagement
and water analysis in Egypt.
- Water Quality Testing and Analysis
- Drinking Water Disinfection
FIRST laboratories provide water testing services for water quality. Water quality analysis
is provided for the world's petroleum, mineral, food, industrial, manufacturing and other
industries. Water testing includes trace analysis capabilities. FIRST water analysis
capabilities vary to include the following Water testing:

Drinking Water Quality Testing and Analysis


Industrial Water Quality Testing and Analysis
Microbiology Testing
Water Content Testing for the Petroleum Industry
Sea Water Analysis
Water Activity Testing (Aw)
Environmental Services

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
-rt

Association
Engineers
LiftingEquipment
of membershiP
Certificate
20t6
[IJe herebgcertifgthat

Environment
Consultancg
FIRST (FCECJ
I Calibration
Eggpt

havingbeenauditedin accordance technicalauditprocedure


uJiththe Flssociation's
specifiedin documentreference LEER 002 has been admittedas a

fflember
Development

flumber3108
Certificate

For and on behalfof LEEF

ChiefExecutive

- 4 RPril2016
Dateof Certificate

- 3 Rpril2017
Dateof expirgof Certificate
and shallbe returnedon demand.lt is not issuedunder,in pursuance
is the propertgof the Flssociation
Thiscertificate or bg
,i;i;;;i;U starurorg onlg'lt is ualidonlgin the countrglisted
oi Cor!in61.ntr.nciionbut bg the authoritgof the Flssociation
above.

:
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
-
-
:
-
- -
- -
- -
- -
-

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
:
- -
- -
- -
- -
- -
- -
-
:
- -
- -
- -
- -
- -
- -
- -
- -
-

: :
- -
- () -
- -
- -
- -

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
- -
-
-
:
- -
- -
- -
- -
- -
- - OCL
-
-

:
- -
- -
-
-
- -
- -
-
-
- -
-
: :
- -
- -
-
24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt
Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
- -
- -
- -
- -

-
:
- -
- -
- -
- -
-
:
- -
- -

- 2000 -

- -

- -
-
-
-
-
-

24 East Autostrad Buildings, Sakr Korish, Maadi, Cairo, Egypt


Tel:(+2)(02)27491365 Fax:(+2)(02)27491406 Mobile:01221732510
Website:www.first-env.comE-mail:info@first-env.com Customer Service:01002227145
-f-t

LiftingEquipment Association
Engineers

of membership
Certificate
2017
[JJeherebgcertifgthat

FIBST Environment
Consultancg (FCECJ
I Calibration
Eggpt

havingbeenauditedin accordance technicalauditprocedure


ulith the Flssociation's
specifiedin documentreferenceLEEH002 hasbeenadmittedas a

Development
fhember

fl umber3108
Certificate

For and on behalfof LEEfl


Chairman

ChiefExecutive
- 4thHpril2017
Dateof Certificate

- 3'dRpril2018
Dateof expirgof Certificate
and shallbe returnedon demand.lt is not issuedunder,in pursuance
is the propertgof the Flssociation
Thiscertificate or bg
virtueof angstatutorgor Government sanction onlg.lt is validonlgin the countrglisted
but bg the authoritgof the Flssociation
aDove.

You might also like