Professional Documents
Culture Documents
Energy Saving
Monitor
E.ON Energy Limited. Registered Ofce, Westwood Way, Westwood Business Park, Coventry, CV4 8LG.
Registered in England and Wales No: 3407430.
Page
Contents Use your Energy Saving
Monitor safely
3 Use your Energy Saving
Getting started 4 Monitor safely
Tuning your sensor and 5
display unit Its important that you take some Do not attempt to repair
Installing the transmitter 6 simple precautions before using your or service any part of the
and sensor jaw Energy Saving Monitor. Energy Saving Monitor. Go to
Adjusting your electricity price 8 eonenergy.com/energymonitor
You wont need to carry out any for help.
Tariff options 9 electrical wiring to install the Energy
Understanding the 10 Saving Monitor. However, care must Do not immerse the equipment
Energy Saving Monitor be taken as its used in and around in water, or any other liquids.
the electricity supply to your property.
Setting the clock 12 Do not expose the equipment
Testing 13 After reading the instructions on to heat, ame, steamy conditions
In control of your energy 14 page 6, if you have any doubt or extreme cold.
about how to install it safely, do
Troubleshooting 16 Do not open the equipment or
not attempt to install it yourself,
How to get in touch 17 but consult a qualied electrician. touch any of its electronic circuitry.
Getting started
In the box youll nd: Tip If the display unit still
shows dashes instead of 0 watts
a minute or so after tuning, then
complete the process again.
Nearly there...
Adjusting your electricity price 3 Press the square button Tariff options 4 Using the up and down buttons
The display unit has been to conrm. There are several different you can now select your lower
pre-programmed with a tariffs available when buying rate cost.
4 The price will then start
default p/kWh unit rate. ashing. Push the up and down electricity for your property. 5 Press the square button to
button to adjust the pence price If you pay different rates for conrm.
You may wish to adjust this to of the electricity. electricity used at different
match the rate youre paying. times of the day, the Energy 6 Using the up and down buttons
5 Press the square button Saving Monitor can be you can now set the time that
Youll nd your electricity rate on to conrm. programmed to allow for this. your normal rate starts.
your energy bill. 6 Repeat this process with the 7 Press the square button to
pence option. 1 Press and hold the up and conrm.
Please follow the setup down buttons together for
instructions below to adjust 7 Press the square button three seconds and release. 8 Using the up and down buttons
the cost settings. to conrm. you can now select your normal
2 You will then see the clock rate cost.
8 The blue LED on the front ashing. Using the up and
1 Push the up button for three of the monitor will ash and 9. Press the square button to
down buttons you can now
seconds and release. the display will resume conrm.
set the time that your lower
2 Push up or down to change normal operation. rate starts. 10 The blue LED on the front of
from euros/cents to pounds/ the monitor will ash and the
3 Press the square button to
pence. display will resume normal
conrm.
operation.
10 11
Once youve correctly set up and installed your 1 The aerial icon conrms that information is being read from
Energy Saving Monitor. The screen on your the transmitter.
display unit will look similar to this:
2 Indicates the number of sensor jaws installed.
3 Energy Now shows you how much energy youre using right now.
1 2 Test it out by switching a light on and off and watch the gures
as they change.
3
4 4 Cost per month shows how much money youre spending.
It changes as you switch electrical items on and off.
5 You can test it by switching on a light. The gures change
automatically to show how much your electricity would cost you
per day and per month if you didnt turn off your appliances.
6
7
5 Down shows you how much you save when you turn an appliance
off or spend as you turn it on. It also shows you the equivalent
level of energy use.
8
6 The graph shows you how much energy youve used
between 7am to 3pm during the previous day, 3pm to 11pm
the previous evening and 11pm to 7am the previous night.
Now that your display unit and transmitter are tuned in, all you need to do is Testing
set the time and you are ready to start using your Energy Saving Monitor. Why dont you now test your In the unlikely event that
monitor by switching off a light? your display unit doesnt show
Setting the clock any change when you test it,
1 Press and hold the square 4 Push the square button once. If you switch off an appliance, you may need to tune it to a
button for three seconds. The blue LED on the front of your monitor will now show you different channel. First carefully
The screen will clear and the the monitor will ash and the the amount you saved per hour, remove the sensor jaw from
hours will ash. display will resume normal per day and per month. your meter and repeat the
operation. process of tuning, installing
2 Use the up and down buttons and setting up the monitor as
to set the correct hours. Congratulations, youve now shown on pages 5 to 9.
The monitor has a 24 hr clock. successfully installed and set
up your Energy Saving Monitor.
3 Push the square button once
and the minutes will ash.
Use the up and down buttons
Energy saving idea
to set the correct minutes.
Dont leave your phone on charge
all the time - remember to unplug it
once its been charged.
Energy saving idea
Low energy light bulbs last up to 15
times longer and cost around 75%
less to run than conventional bulbs.
PowerDown
Save money and hassle by automatically switching off any
equipment linked to your desktop computer.