Professional Documents
Culture Documents
Subject Discipline
Comments
In accordance with AISC 9th Edition - ASD
Properties
Beam:
CS500X172 Full
Fy= 345 MPa M=(0,66 Fy bf tf)* d / 106 = 911 KN.m
Fu= 450 MPa
d= 500.0 mm Q=50% (0,4 Fy d tw) / 103 = 431 KN
t w= 12.5 mm
bf = 500.0 mm
tf = 16.0 mm
A = 21,850 mm2
Af = 8,000 mm2
Calculation Sheet
Subject Discipline
Subject Discipline
Loads
Horizontal Shear (H) = 431 KN End Moment (M) = 911 KN.m
Axial Tension Load (T) = 10 KN Axial Compression Load (C) = 20 KN
Flange
Tension Flange Force FT = M / (d-tf) + T (Af / A) =
FT = 910.8 * 103 / ( 500.0 - 16.0 )+ 10.0 *( 8,000 / 21,850 )= 1,885
Compression Flange Force FC =M / (d-tf) + C (Af / A) =
FC = 910.8 * 103 / ( 500.0 - 16.0 )+ 20.0 *( 8,000 / 21,850 )= 1,889
Maximum Flange Force Ff = 1889 KN
Web
Tension Web Force FW = T (1 - 2 Af / A) =
FW = 10 * ( 1 -2 * 8,000 / 21,850 )= 3 KN
Compression Web Force FW = C (1 - 2 Af / A) =
FW = 20 * ( 1 -2 * 8,000 / 21,850 )= 5 KN
Maximum Web Force Fw = 5 KN
Bolt Properties to Beam Flange Bolts AISC-ASD Tables J3.1 and J3.2
Bolt Diameter (db)= 3/4 in = 19.0 mm
Plate Bolt Hole Size (dh) = 21 mm
Ff
Area of Bolts (Ab) = 285 mm 2 (n1-1)s1
Allowable Tensile Stress (Ft)= 309 MPa ASTM A325 N (n2-1)s2
Allowable Shear Stress (Fv) = 148 MPa Bearing Type Connection
dpf
Subject Discipline
Subject Discipline
Subject Discipline
Ratio = 0.90
Bolt Properties for Web to Shear Plate AISC-ASD Tables J3.1 and J3.2
Bolt Diameter (db)= 3/4 in = 19.0 mm (n3-1)s3
Plate Bolt Hole Size (dh) = 21 mm
Area of Bolts (Ab) = 285 mm 2
Subject Discipline
Block Shear of Web Plate - for axial tension load AISC-ASD Section J4
RBS= 0.30 Av Fu + 0.50 UbsAt Fu (n3-1)s3
Ubs = 1.0
Edge Distance (d3)= 35 mm
Fw
Edge Distance (d4)= 35 mm (n4-
d4 1)s4
d3
At = 2 * ((dpw - 2 * d3 - (n3 -1 )* dh )) * tpw
dpw
At =2 * ( 370 -2* 35 )-( 5 -1 ) * 21 )) * 6.3 = 2,722 mm2
Av = 4 ( d4 + (n4 -1) s4 - (n4-0,5) dh ) tpw
Av = 4 * ( 35 +( 2 -1)* 75 -( 2 - 0,5 ) * 21 )) * 6.3 = 1,978
RBS=( 0.30 x 1,978 * 450 + 0.50 * 1.0 * 2,722 * 450 ) / 10 =3
879
RBS = 879 KN > Fw = 3 KN
Ratio = 0.00
0.5
Edge Distance (d3)= 35 mm
(n3-1)s3
35 mm
Calculation Sheet
Subject Discipline
(n3-1)s3
Av = 2 ( d3 + (n3 -1) s3 - (n3-0,5) dh ) tpw
d4
Av = 2 x ( 35 +( 5 -1)* 75 -( 5 - 0,5 ) * 21 )) * 6.3 = 3,030
At = 2 ( d4 + (n4 -1) s4 - (n4-0,5) dh ) tpw
At = 2 x ( 35 +( 2 -1)* 75 -( 2 - 0,5 ) * 21 )) * 6.3 = 989
RBS=( 0.30 * 3,030 * 450 + 0.50 * 0.5 * 989 * 450 ) / 10 =
3
520
RBS = 520 KN > H = 431 KN
Ratio = 0.83
Calculation Sheet
Subject Discipline
Allowable Shear at Bolt on Web AISC-ASD J3.7 and pages 4-62 and 63 - Tables XI and XII
For edge distance not less than 1 1/2 db and c. to c. spacing of bolts not less than 3 db Find on the tables
with b=3" n3= 5 l= 78 mm = 3.1 " C= 6.87
Actual Lods on Bolt for the Axial Load f1 = Fw / n = 5 / 10 = 0.5 KN
f2 = H / C = 431 / 6.87 = 62.8 KN
Resultant Actual Lods on more loading Bolt R = f1 + f2 = = 63.3 KN simplified
Allowable cap. per one double shear Bolt - Rbolt = 2 Ab Fv = ( 2 * 285 * 148 ) / 103 = 84
Rbolt= 84 KN > R= 63.3 KN
Ratio = 0.75
Subject Discipline
Summay of results
Failure mechanisms
On Flange
Allowable Shear in Bolts at Flange Plate 1.87 NOT GOOD!!!
Allowable Bearing at Bolt Holes on Beam Flange 0.96 OK! PASS
Allowable Bearing at Bolt Holes on Flange Plate 0.81 OK! PASS
Tension Yield of Flange Plate 2.66 NOT GOOD!!!
Tension Rupture of Flange Plate 1.88 NOT GOOD!!!
Block Shear of Flange Plate 0.90 OK! PASS
On Web
Shear Yield of Shear Plate 0.67 OK! PASS
Shear Rupture of Shear Plate 0.96 OK! PASS
Block Shear of Web Plate - for axial tension load 0.00 OK! PASS
Block Shear of Web Plate - for horizontal shear 0.83 OK! PASS
Allowable Shear at Bolt on Web 0.75 OK! PASS
Allowable Bearing at Bolt Holes on Beam Web 0.49 OK! PASS
Allowable Bearing at Bolt Holes on Web Plates 0.49 OK! PASS
Calculation No.
alculation Sheet
Calculation No.
1,885
1,889
(n1-1)s1
NG
AISC-ASD J3.7
alculation Sheet
Calculation No.
OK
alculation Sheet
Calculation No.
AISC-ASD J3.7
OK
AISC-ASD D1
Simplified design work with only 4 plates size dpf2
NG
AISC-ASD B3 and D1
Simplified design working with only 4 plates size dpf2
NG
AISC-ASD Section J4
mm
OK
alculation Sheet
Calculation No.
Calculation No.
AISC-ASD F4
OK
AISC-ASD J4
OK
AISC-ASD Section J4
mm2
KN
OK
AISC-ASD Section J4
alculation Sheet
Calculation No.
mm2
mm2
KN
OK
alculation Sheet
Calculation No.
simplified
KN
OK
AISC-ASD J3.7
OK
AISC-ASD J3.7
OK
alculation Sheet
Calculation No.