You are on page 1of 2

MASSACHUSETTS INSTITUTE OF TECHNOLOGY

DEPARTMENT OF MATERIALS SCIENCE AND ENGINEERING


CAMBRIDGE, MASSACHUSETTS 02139

3.22 MECHANICAL PROPERTIES OF MATERIALS


PROBLEM SET 11

Due in 6 days from assigned date

1.
5. A very large plate in an engineering component, which is in continuous operation for
10 hours each day, is subjected to a mean tensile stress of 200 MPa during service.
Superimposed on this operating stress are fluctuations arising from vibrations, which
have an amplitude or 15 MPa (i.e. total range of 30 MPa) and a cyclic loading frequency
of 50 Hz. Nondestructive crack detection techniques, which have a resolution or 0.2 mm
in crack size, do not reveal any flaws in the component. If a crack where to exist at the
critical location, the operating stress would be normal to the plane of the centrally
located, through-thickness crack and small-scale yielding conditions would prevail in the
plate. The plane strain fracture initiation toughness of the material from which the plate
is make is 100 MPa . The fatigue threshold stress intensity factor range, ,of the
material is 3 MPa for load ratio R=0, and 1.5 MPa for R=0.85, and can be
assumed to be independent of the cyclic frequency.

(a) Which or the following factors is/are most significant in the safe design of the
component against catastrophic fracture:(i) the plane strain fracture toughness, KIc, (ii)
the threshold stress intensity factor range, ,or (iii) the rate of crack growth in the
Paris regime? Why?
(b) Suggest a procedure for the calculation of fatigue life in the plate.
2
3. A disgruntled employee in an engineering company is intent on destroying a large
steel plate used in a valuable engineering component. One evening, after the normal
working hours, he cuts a very sharp notch in the edge of the plate. He orients the sharp
flaw normal to the direction in which tensile stresses are applied to the plate, with the
hope that the flaw would eventually result in catastrophic fracture of the plate. As he is
committing the crime, a bystander telephones the plant foreman at the foremans home.
The foreman, who leaves his home two minutes after the notification is received, travels
to the scene of the crime on his bicycle at an average speed of 15 km/hr. Would he have
reached the plant in time to shut off the equipment before the plate fractures
catastrophically? Here are some useful data for your analysis: (i) The plate is cyclically
loaded uniformly from 5 to 85 kN at a frequency of 75 Hz. (ii) The plate is 18 cm wide
and 0.5 cm thick. (iii) The yield strength of the steel is 1250 MPa and the plane strain
fracture toughness is 48 MPa . (iv) The flaw introduced by the employee is 1 cm in
length, through the thickness of the plate. (v) The bystander, who notified the foreman,
reported to the police, by phone, that, in his judgment, the crack tip opening
displacement corresponding to the peak load of each cycle. (vi) Post-failure
fractographic examination revealed the presence of fatigue striations with a mean
spacing of 2.5 * 10-4 mm at the point where the crack had grown by 2.5 mm from the
initial 1 cm flaw. (vii) The distance from the foremans home to the factory is 5 km.
(viii) The time interval between the two phone calls was 10 minutes. State all your
assumptions clearly.

3
A piston, 9 cm in diameter, is used to increase the internal pressure in a cylinder from 0
to 50 MPa. The cylinder, which is made of peak-ages aluminum alloy (yield strength =
500 MPa, KIc = 35 MPa ), has the following dimensions: length = 20 cm, inner
diameter = 9 cm, and outer diameter = 11 cm. This piston- cylinder arrangement suffered
a malfunction which caused the cylinder to burst. Post failure analyses showed the
presence of a defect in the form of an elliptical flaw 4.4 mm long at the inner wall, 1.5
mm deep an oriented normal to the hoop stress in the cylinder. Compute the magnitude
of the pressure at which the cylinder burst.

You might also like