Professional Documents
Culture Documents
S H E E T M A T E R I A L S
Cam-ORJ
Combination Ring Type Joints
This Ring Type Joint consists of 2 different sizes
RX Ring Type Joint having the same pitch diameter, used for sealing
and flange joint where the mating flanges have
different ring groove dimensions or profiles.
Novus model M12PI
These Ring Type Joints can be produced with
Ring Type Joints with PTFE Inserts
Cam-ORJ either octagonal or oval facings, however they
M12 model RX Ring Type Joints can be supplied are not manufactured in accordance with API
The Cam-ORJ is a standard API 6A octagonal with PTFE inserts. Designed to reduce turbulent specification.
ring joint but with the four angled seating flow and eliminate ring joint and flange corro-
surfaces concentrically serrated and faced with sion. The insert is specially designed with radi-
oxidation inhibited graphite. The gasket offers ally drilled holes ensuring the self-energising
the high sealing efficiency associated with the performance is not affected. The insert is locat-
octagonal design but with the added benefit of ed between the inside diameter of the ring joint
being capable of sealing flanges with minor and the bore of the flange. On assembly, the
damage. Under compression the graphite flows insert is captured between the flanges, filling Lens Rings
into minor imperfections creating a tight seal. the void between ring joint and flange bore.
This is a contact seal for use in high pressure
The Cam-ORJ is available in a range of Alloy piping systems and in pressure vessel heads.
materials and in sizing to suit ASME B16.5 or Lens rings have a spherical surface that requires
API 6A flanges. special matching of the flanges. Effective seal-
ing is obtained at a relatively low bolt loads.
M8 M11 M12
Seating Stress
To achieve a reliable seal, the Ring Type Joint
should be assembled within the following
seating stress parameters:
How to Order
Flange Surface Finish
A correct purchase order should contain the
The Ring Type Joint and the sealing face of the
following information.
groove must be free of indentations, score
marks, tool and chatter marks. 1. Ring Type Joint model eg. M8 R Oval
2. Ring number/size & pressure rating R16/Class 1” 3/600lbs
The maximum flange surface finish for M8, M9, 3. Material/Identification Soft Iron or D
model R, M12 model RX is 1.6µm RA (63RMS). 4. Flange Standard ASME/ANSI B16.5
The maximum flange surface finish for
Note: This can be abbreviated to R16D Oval RTJ
M11 model BX is 0.8µm RA (32RMS)
Ring Type Joints
Novus M12 Model RX Ring Type Joints 23O Tolerances (Inches) *A plus tolerance of 0.008 inches
A* (width of ring) +0.008, -0.000 for width ‘A’ and height ‘H’ is
API Specification 6A Dimensional Data
H* (height of ring) +0.008, -0.000 permitted, provided the variation
in width or height does not
OD (outside diameter of ring) +0.020, -0.000
H exceed 0.004 inches throughout
23O 23O (angle) + or - 0.5O
the entire circumferance.
A
P
23O
23O
23O
Notes: End flanges to API 6D and API 600 use ring joints for equivalent pipe size under ASME/ANSI B16.5 or ASME B16.47 series A
R30 is only suitable for lapped flanges.
Ring Type Joints
23O
Tolerances (Inches)
Novus M8 Model R Oval and A (width of ring) + or - 0.008
B H
B,H (height of ring) + or - 0.020
Novus M9 Model R Octagonal Ring Type Joints
P (average pitch diameter of ring) + or - 0.007
(continued)
A A 23O (angle) + or - 0.5O
API Specification 6A Dimensional Data P P
Novus Sealing and our distributors are fully committed to ensuring our customers throughout the world receive the highest level of quality and technical support
for our products and services. Our technical specialists can provide expertise on all issues associated with sealing performance.
SEALING LIMITED
Novus Sealing Limited, Hunsworth Lane, Cleckheaton, West Yorkshire, England BD19 3UJ
Tel: +44 (0)1274 878787 Fax: +44 (0)1274 862588 www.novussealing.com e-mail:mailbox@novussealing.com
S E A L I N G P T Y LT D
Novus Sealing Pty Ltd., 15 Vinnicombe Drive, Canning Vale, Perth, Western Australia 6155
Tel: +61 (0)8 9455 2155 Fax: +61 (0)8 9455 2165 www.novussealing.com.au e-mail:mailbox@novussealing.com.au
SEALING TECHNOLOGY
Novus Sealing Technology (Shanghai) Ltd., Room 1002, No.738 Shang Cheng Road, Shanghai, China 200120, P.R. China
Tel: +86 (0)21 6102 8975 Fax: +86 (0)21 6102 8976 www.novussealing.com.cn e-mail:mailto:zhuyaqi@novussealing.com.cn
SEALING LIMITED
Novus Sealing Limited, 87 Radio Street, Alberton North, Johannesburg, Gauteng, South Africa
Tel: +27 (0)11 865 4807 Fax: +27 (0)11 902 2173 www.novussealing.com.za e-mail:deon.novussa@vodamail.co.za