Professional Documents
Culture Documents
STR9000 Series
5-Terminal, Low Dropout Voltage Dropper Type
■Features
• 5-terminal regulator with two screw mount package
• Output current: 4.0A
• Low dropout voltage :VDIF≤1V (at IO=4A)
• Fine adjustment of output voltage
• Output ON/OFF control
• Built-in foldback overcurrent protection circuits
■Applications
• For stabilization of the secondary stage of switching power supplies
• Electronic equipment
*Output is turned on when voltage between terminal No.3 and 5 is less than 0.6V, and turned off if more than 2.0V.
66
●STR9000 Series
±0.3
36.0 6.0max.
±0.2 ±0.2
24.4 2.0
±0.1
30°
φ 3.2
±0.3
±0.3
Lot Number
12.0
21.2
Part Number
Flammability: UL94V-0
Weight: Approx. 14.5g
20.0min. 3.0
4.7max.
+0.2
Terminal Connections
2.0 0.6 –0.1
+0.2
1.0 –0.1
q Output (backside of case)
q w e r t
w Output Fine Adjustment
3.5 5.45×4
5.45 e Output ON/OFF Control
r Input
t Ground
■Block Diagram
Tr1
4 1
R4
R2
R1
M
2
Amp.
Drive
Reg.
R6
Protection
VREF
Tr2 3
R7
R5 R8
R3
5
67
●STR9000 Series
■Ta-PD Characteristics
Without Mica
24 With Slicon Grease
150×150×2(3.3°C/W)
Heatsink: Aluminum
Unit: mm
Power Dissipation PD (W)
20
16
100×100×2(5.2°C/W)
12
75×75×2(7.6°C/W)
8
4 Without heatsink
0
–20 0 25 50 75 100
Ambient Temperature Ta (°C)
68
●STR9000 Series
External Variable Output Voltage Circuit q Typical Characteristics of Variable Output Voltage
STR9005
(Ta=25°C)
5.3
1. Variable output voltage with a single external resistor
The output voltage of the STR9000 series may be decreased by insert- 5.2
4.7
VIN VO 20K 50K 100K 500K 1M 5M 10M 50M
4 1 External Resistor REX (Ω)
STR9000 REX
for Vo down STR9012
3 5 2 (Ta=25°C)
+ + 14
13
11
2. Fine adjustment of output voltage
The output voltage may be finely adjusted by using terminals No.1, No.2 10
3 5 2
+ +
VR
15
Variable Output Voltage Range
R2
GND GND 14
13
Note: The fine adjustment range of output voltage for the STR9000 se-
12
ries is ±0.5V max for STR9012 and +1.0V/-2.0V max for STR9015. 20K 50K 100K 500K 1M 5M 10M 50M
External Resistor REX (Ω)
Adjustment exceeding these values may cause start-up errors.
: Insertion of resistor between terminals No. 2 and No. 5
: Insertion of resistor between terminals No. 2 and No. 1
5.4
R1=150 kΩ
R2=150 kΩ R1=100 kΩ R1=100 kΩ
R2= 30 kΩ 18 R2= 20 kΩ
13
Output Voltage VO (V)
5.2
Output Voltage VO (V)
16
5.0 12
14
4.8
11
12
4.6
10 10 0
0 100 200 300 400 500 0 100 200 300 400 500 100 200 300 400 500
VR (kΩ) VR (kΩ) VR (kΩ)
69
●STR9000 Series
■Typical Characteristics
(Ta=25°C)
0.6 5.00
40
lO=4A
30
0.4 4.98
3A
20
2A
0.2 4.96
10 1A
0A
0 4.94 0
0 1.0 3.0 3.0 4.0 –20 0 20 40 60 80 100 120 140 0 5 10 15 17.5
Output Current lO (A) Ambient Temperature Ta (°C) Input Voltage VIN (V)
6 15
Output Voltage VO (V)
5 lO=0A lO=0A
10 1A
1A
4 2A 10 2A
lO=0A 3A 3A
3 1A 4A 4A
2A 5
2 3A 5
4A
1
0 0 0
0 5 10 15 20 0 5 10 15 20 22.5 0 5 10 15 20 22.5
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
6 15
25V
20V
VIN
Output Voltage VO (V)
Output Voltage VO (V)
Output Voltage VO (V)
20V
=16
VIN
25V
16V
5
15V
=13
V
VIN
10
8V
=6V
4 10
5
2 5
0 0 0
0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
Output Current lO (A) Output Current lO (A) Output Current lO (A)
70