You are on page 1of 2

Certificate of Conformance

to Requirements for Welding Electrode

Product Type: FabCO Excel-Arc 71


Classification: E71T-1C/M H8,E71T-9C/M H8
Specifications: AWS A5.20, ASME SFA 5.20
Diameter Tested: .035"; 5/64"
Date Tested: 6/15/2017
Date Generated: 11/30/2017

This is to certify that the product named above and supplied on the referenced order number is of the same classification, manufacturing process, and material requirements as the material which was used
for the test that was concluded on the date shown, the results of which are shown below. All tests required by the specifications shown for classification were performed at that time and the material tested
met all requirements. It was manufactured and supplied by the Quality System Program of Hobart Brothers, which meets the requirements of ISO 9001, ANSI/AWS A5.01, and other specification and
Military requirements, as applicable. This document supplies actual test results of non-specific inspection in conformance with the requirements of EN 10204, type 2.2 certification.

THE STEEL USED IN THIS LOT OF MATERIAL WAS MELTED AND MANUFACTURED IN THE U.S.A.
Test Settings
WFS Travel Speed
Shielding Medium Amps / Polarity Volts ESO in(mm) Preheat F(C) Interpass F(C)
in/min(m/min) in/min(cm/min)
C1 (100% CO2) 325 / DCEP 25 190 (4.8) 1 (25) Room Temp 300(149) 11 (27.9)
M21-ArC-25 325 / DCEP 26 190 (4.8) 1 (25) Room Temp 300(149) 11 (27.9)
C1 (100% CO2) 220 / DCEP 28 670 (17) 1/2 (13) 60(16) 300(149) 10 (25.4)
M21-ArC-25 220 / DCEP 29 670 (17) 1/2 (13) 60(16) 300(149) 9 (22.9)
Mechanical Properties - Tensile
Shielding Medium Ref. No. Testing Conditions Ult. Tensile Strength psi (MPa) Yield Strength psi (MPa) Elong.% in 2"
C1 (100% CO2) PD3506 Aged 48 Hrs 200F 84,000 ( 581 ) 79,000 ( 545 ) 27
M21-ArC-25 PD3507 Aged 48 Hrs 200F 90,000 ( 621 ) 82,000 ( 569 ) 28
C1 (100% CO2) PD3912 Aged 48 Hrs 200F 82,000 ( 565 ) 75,000 ( 514 ) 28
M21-ArC-25 PD3913 Aged 48 Hrs 200F 86,000 ( 592 ) 77,000 ( 530 ) 25
Mechanical Properties - Impact
Shielding Medium Ref. No. Testing Conditions Temp. F (C) Individuals ft.lb.(J) Avg. ft.lb.(J) Type
C1 (100% CO2) PD3506 As Welded 0 (-18) 124,112,106 (168,152,144) 114 ( 155 ) Charpy-V-Notch
C1 (100% CO2) PD3506 As Welded -20 (-29) 88,106,81 (119,144,110) 92 ( 124 ) Charpy-V-Notch
M21-ArC-25 PD3507 As Welded 0 (-18) 111,121,118 (150,164,160) 117 ( 158 ) Charpy-V-Notch
M21-ArC-25 PD3507 As Welded -20 (-29) 107,95,89 (145,129,121) 97 ( 132 ) Charpy-V-Notch
C1 (100% CO2) PD3912 As Welded 0 (-18) 89,90,97 (121,122,132) 92 ( 125 ) Charpy-V-Notch
C1 (100% CO2) PD3912 As Welded -20 (-29) 45,45,66 (61,61,89) 52 ( 70 ) Charpy-V-Notch
M21-ArC-25 PD3913 As Welded 0 (-18) 85,69,80 (115,94,108) 78 ( 106 ) Charpy-V-Notch
M21-ArC-25 PD3913 As Welded -20 (-29) 42,55,46 (57,75,62) 48 ( 65 ) Charpy-V-Notch
Ref.No. Radiographic Inspection Fillet Weld Test
PD3506 Conforms Horizontal : Overhead : Vertical :
PD3507 Non Conforms Horizontal : Overhead : Vertical :
PD3912 Conforms Horizontal : Overhead : Vertical :
PD3913 Conforms Horizontal : Overhead : Vertical :
Chemical Analysis
Shielding Medium / Ref. No C Mn P S Si Cu Cr V Ni Mo Al Ti Nb Co B W Sn Fe Sb N Mg Zn Be Sb As
M21-ArC-25 / CD23694 0.02 1.17 0.011 0.011 0.59 0.04 0.04 0.02 0.02 0.01
C1 (100% CO2) / CD25659 0.03 1.26 0.010 0.006 0.48 0.01 0.04 0.02 0.01 < .01
M21-ArC-25 / CD25660 0.03 1.50 0.009 0.005 0.62 0.01 0.05 0.02 0.01 < .01
C1 (100% CO2) / CD27195 0.03 1.61 0.010 0.013 0.50 0.02 0.05 0.02 0.02 < .01
Diffusible Hydrogen Collected per AWS A4.3
M21-ArC-25 6.1 ml/100g of weld metal for .035 in diameter 34% relative humidity
C1 (100% CO2) 5.4 ml/100g of weld metal for .035 in diameter 34% relative humidity
Dave Thomas, Quality Assurance Rep.
Certification and Limited Warranty - Data for the above supplied product are those obtained when welded and tested in accordance with the above specification. All tests for the above classification were
satisfied. Other tests and procedures may produce different results.

You might also like