Professional Documents
Culture Documents
Data and
Reference
Guide
F I B E RG L A S S C A B L E T R AY S Y S T E M S
Instrumentation Tray Wireway Strut Systems Instrument Stands Third Rail Coverboard
w w w. e n d u r o c o m p o s i t e s . c o m
ENDURO
CABLE TRAY SYSTEMS
Enduro is the world leader in the manufacture and
development of fiberglass cable tray and related products.
As a fully integrated supplier, Enduro offers:
• Full line of cable tray, fittings, supports, fasteners & hanging systems
• Engineering and design assistance
• Manufacturing and fabrication
• Large and small scale testing of its products
The Enduro engineering, manufacturing, and sales team is committed to
delivering the highest quality, cost effective, non-metallic cable tray in the world.
To meet this commitment, Enduro continues to make ongoing product
improvements and innovation. Recent accomplishments and developments
include:
• Non-metallic cable tray that is
conductive and complies with
new ABS requirements.
• Low-smoke, non-toxic cable
tray material that meets USCG
requirements for use in
occupied areas.
The Enduro full-radius, one-piece,
molded fitting with its light weight
and smooth side walls is universally
accepted as the best cable tray fitting.
Enduro incorporates computer aided design to analyze structural and mechanical
characteristics and offers PDMS software for design assistance of cable tray
systems. Comprehensive quality assurance programs have been implemented to
provide consistent and reliable product performance.
Enduro’s manufacturing capability is one of the most diversified within the
composites industry and includes multiple pultrusion lines, continuous lamina-
tion, filament winding, compression, contact, and resin transfer molding.
These processes provide in-house, manufacturing capability for the Enduro cable
tray system, cost efficiency, and the best possible products for our customers.
This catalog includes products, accessories, and engineering data required to
design and install a complete, non-metallic cable tray system. Information is also
provided on Enduro Strut Support Systems, Lay-In Wireway, Instrumentation
Stands, and Third Rail Coverboard.
O
F
C
O
N
T
E
N
T
S
SYSTEM OVERVIEW
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Tray Covers and Hold Downs . . . . . . . . . . . . . . . . . . . . . .37
Parts Visualization Diagram . . . . . . . . . . . . . . . . . . . . . . .4-5 Connector Plates and Fasteners . . . . . . . . . . . . . . . . . . . . .38
3
S
■ FEATURES & ✔ BENEFITS
Y
S ■ Full Integration
T ✔ Quality Control and Delivery
E
■ Conductive Cable Tray
M NEW ✔ Meets ABS Standard for Non-Metallic, Conductive Cable Tray
O ■ UL Listed & CSA Approved
V Channel Type
E ✔ Meet Tighter End User Specs
Instrumentation Tray and
R ■ Corrosion Resistant Inside and Outside
Fittings
V 90° Vertical Molded
Pages 36-37
I ✔ No Rust, Peeling, or Flaking Radius Bends
Page 18
E ■ Easy to Cut and Install
W
✔ Faster Field Modifications
■ Hi-Strength Horizontal Adjustable Bend
✔ Higher Strength to Weight Ratio as Compared to Metal 45° thru 135°
Page 26
■ Lightweight
✔ Installations are Less Labor Intensive, Easy to Handle Cover Hold Down
Clamps
■ Low Maintenance Page 30
✔ More Cost Effective Over Time...Saves $$$
■ No Welding
✔ Safety - No Risk of Sparking Drop Out
Page 34
■ Fire Retardant
✔ Safety - Self Extinguishing - Meets ASTM-E84 Class 1
■ Low Smoke Development / Non-Toxic Resin
NEW
✔ Meets U.S. Coast Guard Standard for Live-In Quarters
and Low Smoke Requirements
■ Flexibility in Design
✔ Meets Customer Needs
■ Non-Conductive Instrument
Support Stands
✔ Safety - Eliminates Potential Shock Hazard Page 52
■ Non-Interfering, Non-Magnetic
✔ Transparent to Radio Waves
■ Low Expansion/Contraction
✔ Less Movement with Temperature Variations
■ Low Thermal Conductivity
✔ Will not Transfer Heat or Cold as Metal does.
■ Full Veil on Pultrusions and Acrylic Surface Coating on All Polyester
& Vinyl Ester FRP Products
✔ Improved Weatherability/Additional Corrosion and UV Protection
■ UV Resistant
✔ Does Not Lose Physical Integrity Outdoors
■ High Impact Resistance
✔ Minimizes Handling Damage
45° Horizontal
■ “C” Channel Molded Radius Bend
Page 19
✔ Space Saving, Minimize Code Violations
■ 1" Rung 90° Horizontal
✔ More Loading Depth Molded Radius Bend
Page 18
■ Mechanical and Adhesive Lock
✔ Prevents Racking – Faster Shipment
■ Molded Fittings
✔ Physically Smaller, Costs Less, Cleaner Look
■ Ventilated Ladder Type Tray
✔ No Need to Derate Cables, Gasses Cannot be Trapped or Transmitted
4
S
Y
Enduro
S
T
E
M
Pushbutton
Cable
Support Stands O
Page 52
V
E
R
Tray
Flat Cover V
Page 29
I
E
W
Straight Sections
Pages 13-15
Splice Plates
Page 32
5
T
E
C
TECHNICAL DATA
H
N
I The following data was obtained from the NEMA and NEC Standards Publications and
C
A other sources to assist in the proper selection of the most appropriate cable tray type offered
L by ENDURO.
D
A STANDARD PUBLICATIONS
T
A NEC (National Electric Code) STANDARDS – Article 318 (current issue applicable sections only)
NEMA (National Electric Manufacturers Association) STANDARDS FOR CABLE TRAY SYSTEMS – FG-1 (current issue)
UL (Underwriters Laboratories, Inc.) STANDARDS FOR NON-METALLIC CABLE TRAY.
CSA INTERNATIONAL (National Standard of Canada) CAN/CSA-C22.2 No. 126 CABLE TRAY SYSTEMS
Such concentrated static load represents a static This combined load may be used to select
weight applied between the side rails at midspan. a suitable load/span designation. (Table 1)
When so specified, the concentrated static load may If the combined load exceeds the working load shown,
be converted to an equivalent load (We ) in pounds the manufacturer should be consulted.
per linear foot (kg/m) using the formula:
6
WEIGHT/FOOT STRAIGHT SECTIONS Table 2 -Vinyl Ester Resin weights are the same as Polyester.
T
Catalog Number E
C
EIL6 H
General ELL3 EHL4 ELL6- EHL6 D-EHL6- EHL8- D-EHL10- N
Number W-R-L W-R-L W-R-L EHZ6-W-R-L W-R-L W-R-L W-R-L I
WR Lbs./Ft. Lbs./Ft. Lbs./Ft. Lbs./Ft. Lbs./Ft. Lbs./Ft. Lbs./Ft. C
SS-06-06 2.0 2.5 3.3 3.8 4.5 5.5 9.2 A
SS-06-09 1.8 2.3 3.0 3.6 4.3 5.3 9.0 L
SS-06-12 1.7 2.2 2.9 3.5 4.2 5.3 8.9
D
SS-06-18 1.6 2.1 2.8 3.4 4.1 5.2 8.9 A
T
SS-09-06 2.3 2.8 3.5 4.1 4.7 5.8 9.5
A
SS-09-09 1.9 2.5 3.2 3.8 4.4 5.5 9.2
SS-09-12 1.8 2.3 3.1 3.6 4.3 5.4 9.1
SS-09-18 1.7 2.2 2.9 3.5 4.2 5.3 8.9
Strength properties of Temperatures Polyester Resin Vinyl Ester Resin Note: Percentages shown are approximate.
reinforced plastics are in Degrees °F % of Strength % of Strength If unusual temperature conditions exist, the
reduced when contin- 75 100 100 manufacturer should be consulted. Below freezing
uously exposed to 100 90 100 temperatures do not adversely affect the load rat-
elevated temperatures. 125 78 100 ing capability of the tray. Fiberglass does not
Working loads shall be 150 68 90 become brittle at below freezing temperatures.
reduced when based 175 60 90 Careful review should be made of applications
on the following: 200 52 75 involving service temperatures over 200°F.
The test values in the following chart were obtained from tests conducted by Enduro’s vinyl ester resin supplier. The values shown,
although obtained from an actual coupon test, are intended for illustrative purposes only, and not for use in design calculations.
The values for polyester are slightly lower.
7
T THERMAL CONTRACTION & EXPANSION Table 5
E
C Table 5 compares the thermal contraction and expansion based on various temperature differentials for fiberglass, steel and aluminum
H
N cable trays. The values shown represent the length of cable tray that will produce a 5/8" movement between expansion connectors for the
I indicated temperature differential. Fiberglass has the least movement.
C Note: Enduro expansion connectors provide for total movement of 5/8".
A
L Comparison Chart for Thermal Contraction & Expansion
D Temp. Differential Fiberglass Steel Aluminum
A °F (°C) Ft. (m) Ft. (m) Ft. (m)
T 25 (14) 417 (126) 320 (97) 162 (49)
A 50 (28) 208 (63) 160 (48) 81 (25)
75 (42) 138 (42) 106 (32) 54 (16)
100 (56) 104 (32) 80 (24) 40 (12)
125 (69) 83 (25) 63 (19) 32 (10)
150 (83) 69 (21) 53 (16) 26 (8)
175 (97) 59 (17) 45 (13) 23 (6)
Two standard composite resin systems are available. For most applications, isophthalic polyester fire-retardant (FR–P) is the more
widely used. A vinyl ester composite fire-retardant resin system (FR–VE) is recommended where strong acids (such as hydrochloric
acid), strong alkalies (such as caustic soda), organic solvents and halogenated organic conditions exist. An abbreviated Guide is
provided below to assist in the selection of the proper resin system for individual application.
All composite material has an ultra-violet light inhibiting chemical additive and has a maximum flame spread of 25 or less, per
ASTM E-84 (Class 1 flame spread). All pultruded products have complete Nexus Veil Coverage (outer surfacing fabric) to provide
maximum chemical and UV protection.
FR = Fire-Retardant P = Polyester Resin VE = Vinyl Ester Resin (*) = Not recommended to exceed this temperature Call = Call for recommendations
Information contained in this chart is based on data from raw material suppliers and collected from several years of actual industrial applications • Temperatures are
not the minimum nor the maximum (except where specifically stated) but represent standard test conditions • The products may be suitable at higher temperatures,
but individual test data should be required to establish such suitability • The recommendations or suggestions contained in this chart are made without guarantee or
representation as to results • We suggest that you evaluate these recommendations and suggestions in your own laboratory or by actual field trial prior to use.
8
TYPICAL PROPERTIES – FRP STRUCTURAL SHAPES Table 7
T
E
Mechanical (coupon) FR-P FR-VE Mechanical (coupon) FR-P FR-VE C
Longitudinal Direction Transverse Direction H
Ultimate Tensile Strength, PSI (ASTM D638) 30,000 35,000 Ultimate Tensile Strength, PSI 7,000 10,000 N
Ultimate Compressive Strength, PSI (ASTM D695) 30,000 35,000 Ultimate Compressive Strength, PSI 15,000 20,000 I
Ultimate Flexural Strength, PSI (ASTM D790) 30,000 35,000 Ultimate Flexural Strength, PSI 10,000 14,000 C
Tensile Modulus, PSI x 106 2.5 3.0 Tensile Modulus, PSI x 106 0.8 1.0 A
Compressive Modulus, PSI x 106 2.5 2.5 Compressive Modulus, PSI x 106 1.0 1.2 L
Flexural Modulus, PSI x 106 1.6 2.0 Flexural Modulus, PSI x 106 0.8 1.0
Ultimate Shear Strength, PSI 5,500 7,000 Ultimate Shear Strength, PSI 5,500 6,000 D
Ultimate Bearing Stress, PSI 30,000 35,000 Ultimate Bearing Stress, PSI 30,000 35,000 A
Izod Impact Strength, Ft.-Lbs. per inch Izod Impact Strength, Ft.-Lbs. per inch T
of notch (ASTM D256) of notch (ASTM D256) 4 5 A
(sample thickness 1/8" except 1/4" for rod) 25 30 Barcol Hardness (ASTM D2583-75) 50 50
Electrical Full Section in Bending
Electric Strength, short term in oil, 1/8", vpm Modulus of Elasticity, PSI x 106 2.5 3.0
(ASTM D149)* 200 200 Tensile Strength, PSI 20,000 25,000
Electric Strength, short term in oil, KV per inch 35 35 Compressive Strength, PSI 20,000 25,000
Dielectric Constant, 60 Hz. (ASTM D150)* 5.6 5.2 Thermal
Dissipation Factor, 60 Hz. (ASTM D150)* 0.03 0.03 Thermal Coefficient of Expansion,
Arc Resistance, seconds (ASTM D495)** 120 120 Inches/Inch/°F (ASTM D696)** 5 x 10-6 5 x 10-6
Fire Retardant Properties Thermal Conductivity, BTU per
Flame Resistance, ign/burn, seconds Sq. Ft./Hr./°F/In. (ASTM C-177-76) 4 4
(FTMS 406-2023) 75/75 75/75 Specific Heat, BTU/Lb./°F 0.28 0.28
Intermittent Flame Test, rating (HLT-15) 100 100 Other
Flammability Test, average time of burning Density, Lbs./In.3 (ASTM D792) 0.065 0.065
5 seconds, average extent of Specific Gravity (ASTM D792) 1.80 1.80
burning 15mm (ASTM D635) Water Absorption, Max. % by weight
Surface Burning Characteristics, maximum (24 hour immersion) (ASTM D570) .50 .50
(ASTM E84) 15 15
* Specimen tested perpendicular to laminate face. Note: 1 PSI = 6.894 K Pa, 1 Ft.-Lb./In. = 5.443 kg-m/m
Contact Enduro for specific values on
** Indicates reported value measured in longitudinal direction.
Low Smoke / Non-Toxic resin properties.
Note: Depending on the specific glass content and resin, the strength and stiffness properties may be significantly higher.
Thread shear strength using fiberglass nut in tensile – Lbs. 1,250 2,200 3,100 4,500 6,500
Transverse shear on threaded rod
– double shear (load Lb.) (ASTM-B565) 3,000 5,000 7,500 12,000 22,000
Transverse shear on threaded rod
– single shear (load Lb.) 1,600 2,600 3,800 6,200 15,000
Compressive strength longitudinal, PSI (ASTM-D695) 54,000 54,000 54,000 54,000 65,000
Flexural strength, PSI (ASTM-D790) 55,000 55,000 55,000 55,000 60,000
Flexural modulus, PSI x 106 (ASTM-D790) 2.0 2.0 2.0 2.50 2.75
Torque strength using fiberglass nut lubricated
with SAE 10W30 motor oil, Ft.-Lbs. 8 18 35 50 110
Dielectric strength, KV/In. (ASTM-D149) 35 35 35 35 35
Water absorption 24 hour immersion
– threaded, % (ASTM-D570) 1 1 1 1 1
Coefficient of thermal expansion – longitudinal In./In./°F 5 x 10-6 5 x 10-6 5 x 10-6 5 x 10-6 5 x 10-6
Max recommended operation temp – based on 50%
retention of ultimate thread shear strength °F 200 200 200 200 200
Stud weight, Lb./Ft. 0.07 0.12 0.18 0.28 0.50
Flammability Self-extinguishing on all.
Note: 1 Ft.-Lb. = .138 kg-M; 1 Lb = .4536 kg, 1 PSI = 6.984 K Pa
The following applies to Tables 9 and 10
1. Refer to Table 9 (FR-VE Resin) for fire retardant properties of threaded rod.
2. Test results are for studs with single nuts only. Proper safety factors should be applied to testing.
3. All values are based on laboratory test results.
9
T
E
C
INSTALLATION GUIDE
H
N
I
C
A
L
D
A
T
A
10
SUPPORT LOCATIONS – CABLE TRAY & FITTINGS Reference: NEMA FG-1 (current issue) T
E
Straight Sections C
LENGTH OF SPAN = L H
Supports must be located so that connec- SPLICE AT
IN MULTIPLE SPAN CONDITION
SPLICE AT N
tors (splice joints) between horizontal runs I
L/4 L/4
D
Standard engineering practice requires that the splice joints be independently of each other and excessive stress will occur at sub- A
T
located where they will resist little or no bending moment. This stantially less loading. A
allows the cable tray system to act as a continuous member with
Vertical straight lengths should be supported at intervals dictated
spans working in conjunction with one another to resist loading.
by the building structure not exceeding 24 Ft. on centers.
When a cable tray system is installed with the splice joints located
directly over the support, the previous continuous span condition A support should be located 2 Ft. on each side of an expansion
is changed to one of a number of simple spans. These spans act connection.
Ø
(.61 m)
1 Ø
Ø 30°, 45°, 90°
2'-0" MAX 2
(.61 m)
2/ R
3
2'-0" MAX
2'-0" MAX
2'-0" MAX
TYP
TYP TYP
(.61 m) (.61 m)
(.61 m)
(.61 m) (.61 m)
TYP
11
ENDURO FIBERGLASS LADDER-TYPE CABLE TRAY SPECIFICATION
T
E 1.0 Scope 4.2 All composite material shall have an ultraviolet light inhibiting
C 1.1 The cable tray system shall conform to the material chemical additive to resist UV degradation.
H and fabrication requirements as per this specification. 4.3 All composite material shall be fire retardant and have a flame
N 2.0 Standards spread rating of 25 or less (Class 1 Rating) when tested in
I accordance with ASTM E-84.
C 2.1 The cable tray system shall conform to applicable sections of:
A 2.1.1 NEMA Standard FG-1 (latest edition) 4.4 All pultruded products shall have a complete surfacing veil to
L provide maximum chemical and UV protection.
2.1.2 National Electric Code (NEC)
5.0 Construction
D 2.1.3 ASTM E-84 (Class 1 Rating) 5.1 Straight section tray shall be fiberglass reinforced meeting all the
A 2.1.4 UL (Underwriters Laboratories, Inc.) Standards for requirements herein described.
T Non-Metallic Cable Trays.
A 5.1.1 The side rail members must turn in.
2.1.5 CSA INTERNATIONAL (National Standard of 5.1.2 All rung to side member connections shall have both a
Canada) CAN/CSA-C22.2 No. 126 Cable Tray Systems mechanical and a chemical (adhesive) lock. The tray
3.0 General shall be assembled by the use of a locking pin made of
3.1 Tray Requirements fiberglass reinforced thermoplastic. The locking pin shall
3.1.1 Tray widths 6" (152mm), 9" (229mm), 12"(305mm), be inserted under pressure with a high strength, chemical
18" (457mm), 24" (610mm), 30" (762mm), resistant adhesive.
and 36" (914mm). 5.1.3 All bonded connections must be sanded to maximize
3.1.2 Lengths (as required): 10 Ft. (3m),and 20 Ft. (6m). adhesion and structural integrity.
3.1.3 Rung spacing (as required): 6" (152mm), 5.1.4 The tray interior shall be clear of all projections or
9.25" (235mm), 12" (305mm), and 18.5" (470mm). sharp objects.
Rung Type (as required): 5.1.5 All straight section lengths shall be pre-drilled to accept
Standard Rung or Marine Rung connector plates.
3.1.4 Radius of fittings (as required): 12" (305mm), 5.1.6 All cut ends and drilled holes (factory and field) shall be
24" (610mm), and 36" (914mm). resin coated.
3.1.5 Resin Systems (as required): 5.2 Fittings are to be pre-fabricated and shall meet all the
Isophthalic Polyester, Vinyl Ester, Halogen-Free requirements herein described.
Polyester, Phenolic, or Low Smoke / Non-Toxic resin.
5.2.1 All fittings shall have a nominal 9.25" rung spacing.
3.2 Loading Requirements
5.2.2 All fittings shall be pre-drilled to accept connector plates.
3.2.1 There shall be three working load classifications of
fiberglass cable tray based on 20 Ft. (6m) support 5.2.3 All fittings shall be designed and installed so as to have
span with a minimum safety factor of 1.5: the same load carrying capacity as the straight sections.
5.2.4 Rung to side member connections shall have both a
Class Working Load
mechanical and/or chemical (adhesive) lock. Fittings
A 50 Lbs./Lineal Ft. shall be assembled by use of a locking pin made of fiber-
B 75 Lbs./Lineal Ft. glass reinforced thermoplastic and/or a stainless steel
rivet. The locking pin shall be inserted under pressure
C 100 Lbs./Lineal Ft. with a high strength chemical resistant adhesive.
• All radius 90° and 45° horizontal and vertical bends,
3.2.2 Span support criteria shall be as specified all tee’s and crosses for tray types using 6" (152mm),
(Reference the following table) and most 4" (101mm) and 8" (202mm), C-channel
members shall be of concentric curved molded design
Support Working Load in Lbs./Lineal Ft.
and made by resin transfer molding.
Span (Ft.) Class A Class B Class C
5.3 Connector Plates and Fasteners:
20 50 75 100
18 61 92 123 5.3.1 Connector plates shall be fiberglass and designed with
sufficient strength so they may be installed between
16 78 117 156
0.2 and 0.3 of the length of the span from the support
14 100 150 200 without derating the load carrying capacity of the tray.
12 139 208 –
5.3.2 Fasteners for connector plates shall be 3/8" (9.5mm)
10 200 – – diameter Type 316 Stainless Steel, Monel, Silicon
Bronze, or FRP studs & hex nuts as required.
• Independent test reports in conformance to
NEMA FG-1 are required. 5.4 Accessories
3.2.3 Nominal loading depth (as required): 5.4.1 The manufacturer shall be capable of providing
2" (51mm), 3" (76mm), 5" (127mm), 7" (178mm) all necessary parts (i.e. clamps, support assemblies, etc.)
and 9" (229mm). for the installation of a complete fiberglass tray system.
4.0 Materials 6.0 Acceptable Manufacturer
4.1 The glass fiber to resin content shall be maintained between 6.1 The fiberglass ladder type cable tray system shall be
45 to 55 percent by weight in all pultruded components except manufactured - pultrusion, compression molded, resin transfer
flat sheet which shall be 35 to 45 percent; and, 25 to 45 molded and/or fabricated by Enduro Systems, Inc., of Houston,
percent by weight in all molded components. Texas USA.
12
STRAIGHT SECTIONS S
T
R
A
I
Typical “[” Shaped Cable Tray G
H
T
S
E
C
CATALOG NUMBERING SYSTEM T
I
The following information will help you order straight sections for your application. Refer to Table 1 in Technical Data section for O
Working Allowable Load Capacity. All cable trays are available in polyester and vinyl ester resin. See page 8 to determine resin system N
required. Cable trays requiring a 2.0 safety factor will be designated with a “D” prefix. See page 6, Table 1. S
Combine all four specification numbers to create the correct catalog number..
Notes:
To order preinstalled Marine Rung add MR to the end of the Cable tray is available with a strut rung upon request,
original tray part number indicating the location(s) of the rung. please see page 35.
Offshore Marine Rung will be the same resin as the tray unless
Solid bottom available upon request.
otherwise specified, as listed in the example here:
ELL3–06–06–20–MR. Rung connections are made with a mechanical & chemical lock.
See specification Page 12, item 5.1.2 for details.
See Page 17 for additional information about
Offshore Marine Rung. Please contact factory for other custom modifications.
C S A I N T E R N AT I O N A L
* The Enduro straight sections listed above are UL Listed for 10 Ft. and 20 Ft. Lengths. All molded and
mitered fittings associated with these trays are also UL Listed.
13
Tray Type 1" Tray Type 15/8"
ELL3 ETL6
S (25mm) (41mm)
T
R
A
LOADING DEPTH
LOADING DEPTH
I Class Class
413/16" (122mm)
113/16" (46mm)
G 8A - 1.5 S.F. 18A - 1.5 S.F.
H Max. Span
6" (152mm)
3" (76mm)
HEIGHT
HEIGHT
T Max. Span Support
Support 18 Ft. (5.5m)
S
E 8 Ft. (2.4m)
C Resin System
T Resin System Polyester
I Polyester 1" 1"
O (25mm) (25mm)
N
S 1/4" (6mm) 1/4" (6mm)
Tray Type
13/8" Tray Type 15/8"
ELL6
(35mm) (41mm)
ETL4
LOADING DEPTH
LOADING DEPTH
Class
413/16" (122mm)
Class
27/8" (73mm)
6" (152mm)
HEIGHT
HEIGHT
Max. Span Max. Span
Support Support
8 Ft. (2.4m) 20 Ft. (6m)
EHL4
(28mm)
EIL6 (41mm)
LOADING DEPTH
Class
LOADING DEPTH
Class
43/4" (121mm)
6" (152mm)
HEIGHT
HEIGHT
14
Tray Type 15/8" Tray Type 13/4"
EHL6 EHL8
(4mm) (44mm) S
T
R
A
LOADING DEPTH
LOADING DEPTH
Class Class
611/16" (170mm)
I
43/4" (121mm)
20C - 1.5 S.F. 20C - 1.5 S.F. G
6" (152mm) H
8" (203mm)
HEIGHT
HEIGHT
Max. Span Max. Span T
Support Support
20 Ft. (6m) 20 Ft. (6m) S
E
C
Resin System Resin System T
Polyester 1" Polyester 1" I
(25mm) (25mm)
O
N
1/4" (6mm) 1/4" (6mm) S
D-EHL6 D-EHL10
(4mm) (70mm)
LOADING DEPTH
LOADING DEPTH
Class Class Please contact
411/16" (119mm)
85/8" (219mm)
20C - 2.0 S.F. 30C - 2.0 S.F. factory on
10" fittings
10" (254mm)
6" (152mm)
HEIGHT
HEIGHT
Max. Span Max. Span and related
Support Support accessories.
20 Ft. (6m) 30 Ft. (9.14m)
EHZ6 (51mm)
LOADING DEPTH
Class
411/16" (119mm)
Max. Span
Support
20 Ft. (6m)
Resin System
Polyester 1"
(25mm)
15
F
FRP CONDUCTIVE TRAY
R
P
C
O
N
D
U
C
T
I
V
E
T
R
A
Y
16
OFFSHORE MARINE RUNG O
F
Conforms to Coast F
S
Guard and ABS Side View
H
O
Requirements for 23/4" (70)
R
Stainless Steel Banding E
1" (25)
of Cables. Allows 3/4"
M
(19)
bands or tie wraps to be A
R
installed perpendicular I
3/16" N
to the cable avoiding (5)
E
damage to the cable
R
jacket. Closed perfora- 11/4" (32) U
tion prevents bands N
G
from slipping off rung.
Provides a 21/2" cable
support surface. Available for easy field installation on existing Enduro cable tray or Top View
for factory installation. To order preinstalled Marine Rung add MR to the end of
the original tray part number indicating the location(s) of the rung. Offshore
Example of Typical Catalog No:
Marine Rung will be the same resin as the tray unless otherwise specified, as listed ELL3–06–06–20–MR
in the example.
USCG COMPLIANCE U
S
C
Offering lightweight, high strength, and corrosion protection, Enduro cable tray has delivered G
reliable, long-term service for floating vessels and off-shore platforms. Manufactured by C
pultrusion process, Enduro Cable Tray with premium grade, polyester resin has O
M
been widely used and acceptable for non-occupied areas. P
L
To expand usage to include occupied areas, Enduro has developed I
A
a new product, which utilizes a low smoke, phenolic resin system. N
Enduro Channel Tray with low-smoke, non-toxic resin system C
E
meets established requirements for Coast Guard inspected vessels
in all spaces.
In accord with approval requirements for occupied areas, Enduro Channel Tray with low-smoke, non-toxic resin system
has been tested per:
• U.S. Coast Guard Policy File Memorandum on the Use of Fiber Reinforced Plastic (FRP) Gratings and
Cable Trays (PFM 2-98)
• IMO Resolution A.653 (16), Recommendation on Improved Test Procedures for Surface Flammability of Bulkhead,
Ceiling and Deck Finish Materials.
• IMO Resolution MSC.61(67), Part 2, Annex 1, Smoke and Toxicity Test.
17
CONCENTRIC CURVED MOLDED FITTINGS
M Concentric curved molded fittings are available in polyester and vinyl ester resin for all 6" [ side rail configurations.
O Also available in some 4" and 8" side rail configurations. Please contact factory for availability. All 6" and 8" fittings carry a
L
D Class C rating according to NEMA standards. EHL 4" fittings carry a Class 20A rating. It is recommended to use expansion connec-
E tor plates and 11/4" long assembly fasteners when connecting to other fittings or straight lengths. Refer to page 11 in the Technical
D Data section for Recommended Support Locations. Rung connections are made with a mechanical and/or chemical lock. Please see
page 12, item 5.2.4 for details. Other sizes and widths available – please contact factory.
F
I Typical Catalog Number: EHB - MC - 6 - 90 - 24 - 24
T
T HOW TO ORDER/
CATALOG NUMBERING Width
I Fitting Designation Type of Curve / Resin Designation (RD) Tray Depth Angle Radius
COVERS: When ordering covers for fittings, use the DIVIDERS: To order fitting with a pre-installed STRUT RUNG / OFFSHORE MARINE RUNG:
prefix “EC” before the catalog number. Note: Fasteners divider, add the letters “EDS” after the catalog Special rungs are available for your cable
for covers are separate order items – see page 29. number. Please indicate positioning of divider. tray system. See page 13 for information.
Example: EC–EHB–MC6–90–24–24 Example: EHB–MC6–90–24–24–EDS
Underwriters
The following Enduro Molded Fitting Types are UL Listed: EHB • EIV • EOV • EHAB • EIVD • EOVD • EHBD • ESR
® Laboratories, Inc. EL • ER • EHT • EHC in 4", 6", and 8" Polyester and Vinyl Ester Tray.
90° VERTICAL MOLDED RADIUS BEND 90° HORIZONTAL MOLDED RADIUS BEND
Typical Catalog No:
EHB–(RD)–90–(W)–(R)
Inside
R
Typical Catalog No: * Also available in 4" and
A EIV–(RD)–90–(W)–(R) 8" side rail configuration.
L
W
** Also available in 4" side
rail configuration.
L
A
† Also available in 8" side
rail configuration.
R
W A
45°
5"
Channel Depth In. (mm)
4" Tray 6" Tray 8" Tray A
A
Radius A L A L A L
45° 5"
12 NA NA 13 211/16
(305) (330) (535) NA NA
5" R
24 161/2 299/16 181/2 3015/16
(610) NA NA (419) (751) (470) (786) R L
36 NA NA NA NA NA NA
(914)
Outside Typical Catalog No: Inside Typical Catalog No:
EOV–(RD)–45–(W)–(R) EIV–(RD)–45–(W)–(R)
X
19
30° VERTICAL MOLDED RADIUS BEND
24 3 /16
M R=24"
O 5
L R=24"
6
D
E
D 5 30°
1111/16 1111/16
30°
F 5
I
T 6
T 5 R=24"
I R=24"
N 24 3 /16
G
S
Outside Available in 6" and Inside
Typical Catalog No: 24" radius depth Typical Catalog No:
EOV–(MC6)–30-(W)–24 channel. EIV–(MC6)–30-(W)–24
X = 2L – 3"
JOINING 30° IV & 30° OV MOLDED Y = 2 A – 5.20"
Y
Outside Inside
Typical Catalog No: EOVA–(RD)–45–(W)–(R) Typical Catalog No: EIVA–(RD)–45–(W)–(R)
11" L
45°
R
11"
A 11" A
R
45°
L 11"
Dimension In (mm)
Radius A L A
12 223/4 391/2 R R
(305) (578) (1003)
24 343/4 * 631/2
(610) (883) (1613)
36 463/4 871/2
(914) (1187) (2223)
* Available in 4", 6" and 8".
Note: Also available tap up.
Please specify when ordering. Tap Down
21
SEGMENTED MOLDED FITTINGS
Segmented molded fittings are available in polyester and vinyl ester resin for all 6" “[” side rail configurations.
All fittings carry a Class C rating according to NEMA standards. It is recommended to use expansion connector plates and 11/4"
S long assembly fasteners when connecting to other fittings or straight lengths. Refer to page 11 in the Technical Data section for
E
G Recommended Support Locations. Rung connections are made with a mechanical and/or chemical lock. Please see page 12, item
M 5.2.4 for details. Other sizes and widths available – please contact factory.
E
N
T
E Typical Catalog Number: EHB - SMC - 6 - 90 - 24 - 24
D HOW TO ORDER/
CATALOG NUMBERING Width
M Fitting Designation Type of Curve / Resin Designation (RD) Tray Depth Angle Radius
SYSTEM
O EHB Horizontal Bend SMC Segmented Molded / Polyester 6 30 6 24
L EIV Vertical Inside SMV Segmented Molded / Vinyl Ester 45 9
D EOV Vertical Outside 60 12
E EHT Horizontal Tee 90 18
D EHC Horizontal Cross 24
EVT Vertical Tee* 30
F * For vertical tee specify “Up” or “Down” at end of catalog code. 36
I
T
T COVERS: When ordering covers for fittings, use the DIVIDERS: To order fitting with a pre-installed STRUT RUNG / OFFSHORE MARINE RUNG:
I
N prefix “EC” before the catalog number. Note: Fasteners divider, add the letters “EDS” after the catalog Special rungs are available for your cable
G for covers are separate order items – see page 29. number. Please indicate positioning of divider. tray system. See page 35 for information.
S Example: EC–SMC–6–90–24–24 Example: EHB–SMC-6–90–24–24–EDS
RADIUS BEND 6 (152) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
9 (229) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
12 (305) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
18 (457) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
24 (610) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
30 (762) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
36 (914) 371/4 (946) 5213/16 (1341) 491/4 (1251) 695/8 (1768)
Outside
Typical Catalog No:
R EOV–(RD)–90–(W)–(R)
A
R
R
L
Inside R
Typical Catalog No:
EIV–(RD)–90–(W)–(R)
A
Note: On all illustrations
(W) = Width of the
inside distance from
tray wall to tray wall.
22
90° HORIZONTAL SEGMENTED MOLDED RADIUS BEND Typical Catalog No:
EHB–(RD)–90–(W)–(R)
Dimension In. (mm)
24" (610) Radius 36" (914) Radius
L W
Width A L A L
6 371/2 531/16 491/2 491/2 S
(152) (953) (1348) (1257) (1257) E
12 431/2 611/2 551/2 781/2 G
(305) (1105) (1562) (1410) (1994) A M
18 491/2 70 611/2 87 E
(457) (1257) (1257) (1562) (2209)
N
24 551/2 781/2 671/2 957/16 T
(610) (1410) (1994) (1715) (2424)
30 611/2 611/2 – –
R
E
(762) (1562) (1562) – – R D
36 671/2 957/16 791/2 1127/16
(914) (1715) (2424) (2019) (2856) W M
O
A L
D
E
45° HORIZONTAL SEGMENTED MOLDED RADIUS BEND 45° VERTICAL SEGMENTED MOLDED RADIUS BEND D
W
L
Outside
A Typical Catalog No:
EOV–(RD)–45–(W)–R
Dimension In. (mm) A
24" (610) Radius 36" (914) Radius
Width A L A L
R
6 (152) 159/16 (395) 261/2 (673) 191/8 (486) 35 (889) R
9 (229) – – – –
12 (305) 219/16 (548) 303/4 (781) 251/8 (638) 393/4 (1010)
A
18 (457) 279/16 (700) 35 (889) 311/8 (791) 431/2 (1105)
24 (610) 339/16 (852) 391/4 (997) 373/8 (950) 473/4 (1213)
Inside
30 (762) 399/16 (1005) 431/2 (1105) – – Typical Catalog No:
36 (914) 459/16 (1157) 473/4 (1213) 491/8 (1248) 563/16 (1427)
EIV–(RD)–45–(W)–R
L
F
I 90° VERTICAL SEGMENTED MOLDED RADIUS TEE-DOWN Typical Catalog No: EVT–(RD)–90–(W)–(R) TAP DOWN
T L
T
I
N
G
S Dimension In. (mm)
24" (610) Radius 36" (914) Radius
Width A L A L
R
6 371/4 681/2 491/4 921/2
(152) (946) (1740) (1251) (2350)
9 371/4 681/2 491/4 921/2
(229) (946) (1740) (1251) (2350) R A
12 371/4 681/2 491/4 921/2
(305) (946) (1740) (1251) (2350)
18 371/4 681/2 491/4 921/2 R
(457) (946) (1740) (1251) (2350)
24 371/4 681/2 491/4 921/2 R
(610) (946) (1740) (1251) (2350)
30 371/4 681/2 491/4 921/2
(762) (946) (1740) (1251) (2350)
36 371/4 681/2 491/4 921/2
(914) (946) (1740) (1251) (2350)
90° VERTICAL SEGMENTED MOLDED RADIUS TEE-UP Typical Catalog No: EVT–(RD)–90–(W)–(R) TAP UP
COVERS: When ordering covers for fittings, use the DIVIDERS: To order fitting with a pre-installed STRUT RUNG / OFFSHORE MARINE RUNG:
prefix “EC” before the catalog number. Note: Fasteners divider, add the letters “EDS” after the catalog Special rungs are available for your cable
for covers are separate order items – see page 29. number. Please indicate positioning of divider. tray system. See page 35 for information.
Example: EC–EHB–HL4–90–24–24 Example: EHB–HL4–90–24–24–EDS
Underwriters
The following Enduro Mitered Fitting Types are UL Listed and CSA Approved:
® Laboratories, Inc.
CSA INTERNATIONAL
EHB • EIV • EOV • EIVA • EOVA • EHT • EHC • EVT in 4", 6", and 8" Polyester and Vinyl Ester Tray.
M
I A
T W
m .
in
)
E
m
(3 3.5
1
Ø
43
R
E 15 in.
L
R
D (381 mm)
F Angle Ø
I 30° Angle 45° Angle
T R Dim. Depth* Depth*
T In. 4" 6" 8" 4" 6" 8"
I (mm)
N A 103/16 1115/16 1311/16 123/8 1313/16 153/16
(259) (303) (348) (314) (351) (386)
G
S L 2611/16 2611/16 2611/16 249/16 249/16 249/16
(678) (678) (678) (624) (624) (624)
Ø
.7
)
16
6 (152) 13 (330)
9 (229) 16 (406)
12 (305) 19 (483)
18 (457) 25 (635)
A
24 (610) 31 (787)
30 (762) 37 (940)
36 (914) 43 (1092)
"
W 1'-4
4 0 6)
( W
A Note: On all illustrations
(W) = Width of the
inside distance from
tray wall to tray wall.
26
30°/45° INSIDE VERTICAL RADIUS BEND
Note: All dimensions are to the nearest 1/4". Typical Catalog No: EIV–(TD)–45–(W)–(R)
R
12" Radius 24" Radius 36" Radius
Dim.
In. Depth Depth Depth
(mm) 3" 4" 6" 8" 3" 4" 6" 8" 3" 4" 6" 8"
8 9 10 12 9 10 12 14 11 12 14 15
M
A A (203) (229) (254) (305) (229) (254) (305) (356) (279) (305) (356) (381) I
30°
18 18 18 18 24 24 24 24 30 30 30 30 T
W L (457) (457) (457) (457) (610) (610) (610) (610) (762) (762) (762) (762) E
111/16 121/2 137/8 149/16 16 177/16 181/8 191/2 2015/16 R
L
A * (281) (318) (352) * (370) (406) (443) * (470) (495) (532) E
45°
* 197/8 197/8 197/8 * 283/8 283/8 283/8 * 367/8 367/8 367/8 D
L (505) (505) (505) (721) (721) (721) (937) (937) (937)
* Contact factory for availability of 3" (76mm).
F
I
30°/45° OUTSIDE VERTICAL RADIUS BEND T
T
Typical Catalog No: EOV–(TD)–45–(W)–(R) I
Note: All dimensions are to the nearest 1/4". L
N
12" Radius 24" Radius 36" Radius G
Dim. Depth Depth Depth S
In.
(mm) 3" 4" 6" 8" 3" 4" 6" 8" 3" 4" 6" 8"
7 8 10 10 9 10 12 12 11 12 14 14
A (178) (203) (254) (254) (229) (254) (305) (305) (279) (305) (356) (356)
30°
17 17 18 18 23 23 24 24 29 29 30 30 A
L (432) (432) (457) (457) (584) (584) (610) (610) (737) (737) (762) (762)
R
103/4 123/4 143/4 145/16 165/16 185/16 1713/16 1913/16 2113/16
A * (273) (324) (375) * (364) (414) (465) * (452) (503) (554)
45°
* 193/16 209/16 22 * 2711/16 291/16 301/2 * 361/8 379/16 39 W
L (487) (522) (559) (703) (738) (775) (918) (954) (991)
W
A
90° INSIDE VERTICAL RADIUS BEND
Typical Catalog No: EIV–(TD)–90–(W)–(R)
28
STRAIGHT SECTION COVERS
Cable tray covers are recommended for those areas where the cable needs protection from falling objects, adverse weather
conditions, etc. Available in polyester and vinyl ester resin types in 10 Ft. (3m) sections in both flat and peaked design.
When ordering flat cover for fittings, refer to pages 18, 22 and 25. If vinyl ester is requested, substitute “V” for “P” as in the following
example: EVC-06 x10'. If Low Smoke / Non-Toxic Resin is requested, substitute “Y” for “P” in the following example: EYC-06-04.
In addition to cover, solid bottom also available. See page 30 for cover accessories. S
T
FLAT COVER R
A
Installation Methods for I
G
Flat Cover: H
Thermoplastic Drive Rivets (Part No. R-25) T
are the most economical method, but do
require field drilling. S
E
It is recommended rivets be installed on C
24" centers along both side rails. T
I
Cover Hold Down Clamps and Enduro O
Stand Offs allow cover to be removed for Flat cover Flat cover N
Tray Width for “C” Wt./LF for “Z” Wt./LF
easy access to cables. In. (mm) tray types tray types C
catalog no. catalog no.
It is recommended to use seven pair at O
6 (152) EPC-06 0.57 EZC-06 0.95 V
1'6" on center per 10 Ft. length of cover. 9 (229) EPC-09 0.86 EZC-09 1.24 E
Add ventilation height 2" for Flat Cover. 12 (305) EPC-12 1.14 EZC-12 1.52 R
S
18 (457) EPC-18 1.71 EZC-18 2.09
24 (610) EPC-24 2.28 EZC-24 2.66
30 (762) EPC-30 2.85 EZC-30 3.23
36 (914) EPC-36 3.42 NA NA
Peaked Cover Flat Cover
PEAKED COVER
11.25° H
29
CLAMPLESS FLAT COVER FOR CHANNEL TRAY
Installation Methods for
Clampless Flat Cover:
Eliminates the need for Hold
Down Clamp for a quicker
and easier field installation. Stainless Embedded Nut
Recommended to be purchased Pre-installed by Enduro
S with a cable tray straight section
T
R matching the clampless flat
A cover section.
I Typical Catalog No:
G A total of three pairs of stainless embedded nuts are pre-installed to the cable tray EPC–CL–(Tray Width)–P
H channels by Enduro. Contact factory for metal types available on embedded nuts.
T 1/4"
Available Tray Widths (inches):
Diameter stainless fasteners and flat washers are also included and shipped 6 / 9 / 12 / 18 / 24 / 30 / 36
S separately.
For Vinyl Ester resin Substitute “V” for “P”
E
Contact Enduro regarding fitting availability on this type of cover system. For Low Smoke / Non-Toxic resin Substitute “Y” for “P”
C
T
I ACCESSORIES FOR STRAIGHT SECTION COVERS
O
N
COMPLETE COVER HOLD DOWN
C
O Centerline of .25 ø
Holes 4 Places Recommended Usage:
V 3/4''
To secure cover to tray in an outdoor application. Best
E 3/16''
R
SS Nut 3/4'' suited for a high wind situation.
4 Required
S
B = Tray Depth + 2.5"
Resin Designation:
3/16'' SS Threaded Rod Tray P = Polyester
Depth
V = Vinyl Ester
Catalog Number
FRP I-Bar
2 Required CCHD - (Tray Depth)(Resin Designation) x (W)
Tray Width + 3"
Example: CCHD-6Px24
3/8" x 11/4"
3/8" x 11/4" Catalog Number Tray Type Resin
316 SS Bolt, 316 SS Bolt,
Flat Washer, ESO All Tray Types Vinyl Ester Flat Washer,
and Lock Washer ESOP All Tray Types Vinyl Ester and Lock Washer
Two Required Two Required
30
SPLICE PLATES & FASTENERS
Enduro offers a full line of fiberglass splice plates designed to provide
a structural transition between straight sections and fittings.
It is important to refer to NEMA FG-1 regarding proper tray installation as it pertains
to support and splice plate locations for straight sections and fittings. Refer to page 10
for recommended support locations.
Splice plates and fasteners are sold separately and are not provided as standard with S
P
straight sections or fittings due to the many hardware options. L
All plates have 7/16 " pre-drilled bolt holes. I
The catalog numbers contained herein are for Polyester Resin connector plates. For Vinyl Ester, Low Smoke / Non-Toxic, or Stainless C
E
Steel connector plates, insert the letter as indicated in these examples:
Example: ESP–6C–180 Polyester P
ESP–6V–180 Vinyl Ester L
ESP–6Y–180 Low Smoke / Non-Toxic A
ESP–6SS–180 Stainless Steel T
Expansion plates have 1" slotted holes allowing 5/8" total contraction and expansion. E
S
Refer to Table 5 on page 8, Thermal Contraction and Expansion, for maximum spacing between expansion joints.
&
CONNECTOR PLATES Connector / Splice Plate Catalog Numbers F
Channel #Bolt Sets 90° 45° 30° 22.5° A
Depth (in.) Per Plate Straight Expansion Vertical Vertical Vertical Vertical S
T
3 4 ESP-3C-180 EEP-3C-180 EVS-3C-90 EVS-3C-45 EVS-3C-30 EVS-3C-22.5 E
4 4 ESP-4C-180 EEP-4C-180 EVS-4C-90 EVS-4C-45 EVS-4C-30 EVS-4C-22.5 N
6 8 ESP-6C-180 EEP-6C-180 EVS-6C-90 EVS-6C-45 EVS-6C-30 EVS-6C-22.5
E
R
8 8 ESP-8C-180 EEP-8C-180 EVS-8C-90 EVS-8C-45 EVS-8C-30 EVS-8C-22.5 S
10 12 ESP-10C-180* EEP-10C-180** ** ** ** **
* See drawing page 33. ** Contact factory for availability. For 6" & 8" channel heavy duty splice plate, please see page 33.
ASSEMBLY FASTENERS
Type Set Includes Size For Use With Tray Types Catalog No.
316 Stainless Steel Bolt Set Bolt, nut, 2 flat washers, 1 lock washer 3/8"-16 x 11/4" All tray types (except 10" Channel*) 505167SS
316 Stainless Steel Bolt Set Bolt, nut, 2 flat washers, 1 lock washer 3/8"-16 x 11/2" All tray types (except 10" Channel*) 505168SS
Monel Bolt Set Bolt, nut, 2 flat washers, 1 lock washer 3/8"-16 x 11/4" All tray types (except 10" Channel*) 606167M
FRP Studs & Nuts Stud and 2 nuts 3/8"-16 x 2" ELL3, ELL4, ELL6, EIL6, EMZ6 707166F
FRP Studs & Nuts Stud and 2 nuts 3/8"-16 x 21/2" EHL6, EHL8, EHV6 707167F
Silicon Bronze Bolt Set Bolt, nut, 2 flat washers, 1 lock washer 3/8"-16 x 11/4" All tray types (except 10" Channel*) 808167SB
Note: It is recommended that expansion connector plates and 11/4" long assembly fasteners be used when connecting mitered fittings to
molded fittings or straight lengths.
* Contact factory for hardware.
31
TYPICAL DIMENSIONS FOR SPLICE PLATES 45° VERTICAL
7/16" (11) 21/8"
Typical Dimensions Hole (54)
Channel Depth Inches (mm)
Inches (mm) A B C
A
3 (76) 13/4 (44) 1 (25) -0-
4 (102) 2 (51) 1 (25) -0- 11/4"
(32)
6 (152) 45/8 (117) 1 (25) 25/8 (67)
47/8" 45°
S 8 (203) 6 (152) 111/16 (43) 25/8 (67) (124) C
P
L
I B
C
E STRAIGHT SECTION EXPANSION 90° VERTICAL
P 7/ 16" x 1"
L 45/8"
(11 x 25)
A A
11/4"
Slot (117)
T (32)
E
S
21/ 8"
(54)
& 83/4"
41/ 8"
(105) 61/ 4" Field
(222) 107/8"
F (156)
(276) Drilling
A Required
S
T 7/ 16"(11)
E Hole
N C B
E
R
S 30° VERTICAL 22.5° VERTICAL 90° HORIZONTAL
A
B C
11/4"
(32)
30° 22.5°
21/8"
57/16" (54)
(138)
57/16"
(138)
B
A
C
7/16" (11)
Hole
32
ADJUSTABLE HORIZONTAL ADJUSTABLE VERTICAL
7/16" x 1"
6"
(152) (11 x 25) 1"
Slot, Typ. 51/16" (25)
(129)
1"
(25)
45/8" 25/8"
(117) (67)
S
P
L
63/8" 21/8"
(162) (54)
I
C
E
Typical Dimensions
P
Note: For Vertical Adjustable Plates use Catalog No. 505168SS hardware L
A
HEAVY DUTY SPLICE PLATE T
E
S
C8 x 13/4" x 5/16"
33
CABLE TRAY ACCESSORIES
Divider strip is supplied in ten foot lengths. Unless indicated otherwise, dividers are intended for field installation.
DIVIDER STRIPS To order straight sections with divider installed, simply add the letters EDS (for riveted), or ADC (for adjustable), after the
straight section catalog number. Example: EHL6–12–12–20–EDS Indicate installation position. For easier installation,
dividers can be furnished with factory-drilled
Riveted notching with additional cost. Inquire for Catalog
For securing riveted divider Designation Number.
3
to tray we use /16" SS rivets. Tray Type Catalog No.
We also have available
C thermoplastic drive rivets Polyester EDS-P Refer to
A (see below, right) which Vinyl Ester EDS-V the Fitting
B require field drilling. Section for
Low Smoke / Non-Toxic EDS-Y
L ordering
E Adjustable factory
For “ ” Side Rail (Polyester) ADC-1P*
T installed
R For “ ” Side Rail (Vinyl Ester) ADC-1V* dividers for
A For “ ” Side Rail (Low Smoke / Non-Toxic) ADC-1Y* pre-assembled
Y For “ ” Side Rail ADC-2P fittings.
A * Available for 3",4", 6", 8" only.
C
C This Guide becomes a clamp with use of a 316 SS set screw on top.
34
In Polyester, Vinyl Ester, or Low Smoke / Non-Toxic Resin
FLOOR / PANEL FLANGE PLATE • For Vinyl Ester substitute “V” for “P”.
B
• For Low Smoke / Non-Toxic add “Y” for “P”.
C
For Vinyl Ester Resin substitute “V” for “P”. Fasteners not included. A
HOLD DOWN CLIP & EXPANSION GUIDE B
For Low Smoke / Non-Toxic Resin add “Y” for “P”.
L
E
Tray Designation Part Number Dimension A Dimension B
7/16"x 7/8" T
ELL XHDC-LP * 1/4 (6.4) 1/2 (12.7) A
B Slot 3/4" (19) R
ELL/EIL/EHL/EHZ XHDC-HP† 5/16 (7.9) 19/32 (15.1) A
3/8 (9.5) 11/16 (17.5) 13/4 (4.45)
CL Y
D-EHL XHDC-DP† 31/4 (82.6)
3/4 (20.6)
D-EHL 10 XHDC-10P *† 1/2 (12.7) A
C
* These parts do not have the 7/16" x 7/8" slot. They have a 7/16" diameter hole located 7/8" from the outer edge instead of 3/4". C
† This part will allow a 3/16" expansion movement. To reduce expansion, please contact factory. E
S
S
O
FIELD INSTALL RUNG Enduro Strut Rung R
To order, create the following part number: I
EFSR - (Tray Width) - (PE or VE) E
Standard Cable Tray Rung S
To order, create the
Example for
following part number:
6" Wide Rung,
EFIR - (Tray Width) - (PE or VE)
Polyester Resin:
EFSR-06-PE
Example for 6" Wide Rung, Polyester Resin: EFIR-06-PE
Hardware not included.
Hardware not included.
• Seals exposed fibers after any field cuts. Fiberglass to Fiberglass adhesive
• Restores gloss and luster to weathered fiberglass. for custom fabrication or repair.
• Seals exposed FRP threads after installation Meets NSTA
of DuroThread fiberglass threaded rod and hex nuts. and UPS
• For Polyester and Vinyl Ester resin products. requirements
• Clear color. for sea and
Meets NSTA and UPS requirements for sea and ground
ground transportation. transportation.
35
CHANNEL TYPE INSTRUMENTATION TRAYS
Enduro channel type instrumentation tray is designed for light loads of individual
wiring or pneumatic tubing. As illustrated, it is offered in solid or ventilated construction.
Ventilated Channel Type Tray has .75" (19mm) diameter holes on 9.25" (235mm) or 12" (305mm)
centers staggered left and right in the web.
All straight sections and pre-assembled fittings are pre-drilled to accept flange splice plates.
All splice plates and fasteners are separate order items.
Catalog No.
Channel Size
Width x Depth
C Solid Ventilated In. (mm) Wt. / Ft.
H
A EIS-200 x L EIP-200 x L 2x1 (51 x 25) 0.35
N EIS-300 x L EIP-300 x L 3x1 (76 x 25) 0.68
N EIS-400 x L EIP-400 x L 4 x 11/8 (102 x 35) 0.94
E EIS-600 x L EIP-600 x L 6 x 15/8 (152 x 35) 1.34
L
EIS-600D x L EIP-600D x L 6x2 (152 x 51) 1.5
T EIS-800 x L EIP-800 x L 8 x 13/4 (203 x 35) 2.60
Y EIS-1000 x L EIP-1000 x L 10 x 23/4 (254 x 70) 4.10
P
E Available in Polyester, Vinyl Ester and Low Smoke / Non-Toxic resin types. For Vinyl Ester add VE; for Low Smoke / Non-Toxic add Y for resin designa-
tion as in the following examples: EIS–VE–200 x 10 or EIS–Y–200 x 10 available in 10 Ft. (3m) and 20 Ft. (6m) sections. Substitute 10' or 20' for “L”.
I
N
S Part Span Max Loading Max Deflection
T INSTRUMENTATION TRAY LOADING Table 9
Number Ft. (m) Lbs./Ft. (m) In. (mm)
R
U EI( )-200 5 (1.5) 4.0 (5.94) .5 (12.7)
M EI(S) = Solid EI( )-300 5 (1.5) 3.9 (5.79) .5 (12.7)
E EI(P) = Punched EI( )-300 8 (2.4) 1.0 (1.48) .8 (20.3)
N The loads on Table 7 are based on limiting the EI( )-400 8 (2.4) 2.8 (4.16) .8 (20.3)
T deflection to a value equal to 1⁄120th of the span. EI( )-400 10 (3.0) 1.5 (2.23) 1.0 (25.4)
A EI( )-600 10 (3.0) 2.8 (4.16) 1.0 (25.4)
T Reduce loads by 10% for punched tray.
EI( )-800 10 (3.0) 5.2 (7.73) 1.0 (25.4)
I
O EI( )-1000 10 (3.0) 20.0 (29.73) 1.0 (25.4)
N EI( )-1000 15 (4.5) 3.9 (5.79) 1.0 (25.4)
90°
R
R 90°
R R
R
90°
R
A A
90° VERTICAL INSIDE MOLDED 90° VERTICAL OUTSIDE MOLDED 90° HORIZONTAL MOLDED
Radius “A” Radius “A” Radius “A”
In. (mm) Catalog No. In. (mm) In. (mm) Catalog No. In. (mm) In. (mm) Catalog No. In. (mm)
18" (457) EIS-MC90IV-18-600 223/4 (578) 12" (305) EIS-MC90OV-12-600 161/4 (413) 12" (305) EIS-MC90HB-12-600 223/4 (578)
24" (610) EIS-MC90IV-24-400 2811/16 (729) 24" (610) EIS-MC90OV-24-400 285/16 (719) 24" (610) EIS-MC90HB-24-400 3213/16 (833)
EIS-MC90IV-24-600 283/4 (730) EIS-MC90OV-24-600 281/4 (718) EIS-MC90HB-24-600 343/4 (883)
EIS-MC90OV-24-800 283/16 (716) EIS-MC90HB-24-800 3611/16 (932)
36
MITERED FITTINGS FOR CHANNEL TYPE INSTRUMENTATION TRAYS
W 22°–30' 22°–30'
45° R
A
45°
10" 22°–30' R
R R
A
A 10"
22°–30' 10"
22°–30'
45° W
R W
R
22°–30' C
H
A
90° VERTICAL INSIDE BEND 90° VERTICAL OUTSIDE 90° HORIZONTAL BEND N
“A” “A” “A”
N
Catalog No. In. (mm)
E
Catalog No. In. (mm) Catalog No. In. (mm)
L
12" (305) Radius
T
24" (610) Radius
S
18" (457)
W1
Note: Substitute “P” in place of “S” for punched channel. Example: EIP-HT-200 Note: Substitute “P” in place of “S” for punched channel. Example: EIP-HC-200
37
CHANNEL TRAY “FLANGE” SPLICE PLATES
Channel Size Connector Plate Catalog Numbers
(In.) Straight Expansion 90° Vert. 45° Vert. 30° Vert. 22.5° Vert. 90° Horiz. 45° Horiz. 30° Horiz. 22.5° Horiz.
2 EISP-180-200 EISP-X-180-200 EISP-90V-200 EISP-45V-200 EISP-30V-200 EISP-22V-200 EISP-90H-200 EISP-45H-200 EISP-30H-200 EISP-22H-200
3 EISP-180-300 EISP-X-180-300 EISP-90V-300 EISP-45V-300 EISP-30V-300 EISP-22V-300 EISP-90H-300 EISP-45H-300 EISP-30H-300 EISP-22H-300
4 EISP-180-400 EISP-X-180-400 EISP-90V-400 EISP-45V-400 EISP-30V-400 EISP-22V-400 EISP-90H-400 EISP-45H-400 EISP-30H-400 EISP-22H-400
6 EISP-180-600 EISP-X-180-600 EISP-90V-600 EISP-45V-600 EISP-30V-600 EISP-22V-600 EISP-90H-600 EISP-45H-600 EISP-30H-600 EISP-22H-600
8 EISP-180-800 EISP-X-180-800 EISP-90V-800 EISP-45V-800 EISP-30V-800 EISP-22V-800 EISP-90H-800 EISP-45H-800 EISP-30H-800 EISP-22H-800
10 EISP-180-1000 EISP-X-180-1000 * * * * * * * *
* Contact factory for availability.
(222)
83/4"
4 (102) 1 (25) #505139SS * 1/4"–20 x 1" bolt sets for EIS-800 41/8" (156)
T 6 (152) 11/4 (32) 1/4" – 20 x 1"* 21/8" (105)
Y 8 (203) 11/4 (32)
channel tray only. All others use (54)
#505141SS
P 1/4 - 20 x 3/4". Contact factory for bolt 11/4"
10 (254) 21/4 (57)
E sets for 10" channel. A (32)
2
I
N
S 90° VERTICAL 45° VERTICAL 30° VERTICAL
T
11/4"
R (32) 21/8"
U (54)
6"
M (152)
A
2
E
N 45° 30°
T A
A
(152)
A
T
6"
I
O 47/8 "
N (124)
T
R 22.5° VERTICAL 90° HORIZONTAL 45° HORIZONTAL
A
Y
S A A 45°
A 2
22.5° 2
(136)
53/8"
47/8"
53/8"
(124)
(136)
30° 22.5°
5/16 Ø x 1 (8 x 25)
SLOTS
38
DuroStrut STRUT & SUPPORT SYSTEMS
See Guide Specification on Page 43
7/16" 3/4" 7/16"
Polyester Resin •
Catalog No. EC-10 EC-158 EC-158D
T
Vinyl Ester Resin Y
EC-VE-10 EC-VE-158 EC-VE-158D P
Low Smoke / Non-Toxic I
EC-Y-10 EC-Y-158 EC-Y-158D C
Lbs./Ft. 0.47 0.68 1.36 A
L
S
PBD PBS PB-1V U
STRUT POST BASE All holes 7/16"(11) P
All
P
• Available for
All
holes 61/2" holes
7/16" (11)
O
both single 3"
7/16"(11) (165)
R
and double
(76) 3"
(76)
T
strut. 6 1/
2"
(16
5) (12
7) 5"(
12 7)
7"
(17
8)
I
5" 7)
5"(
12 "
1 /8
2 4)
N
(5 S
Single - Available in Vinyl Ester Catalog No. PB-1V T
Single - Available in Polyester or Polyurethane Catalog No. PBS-PE (Polyester) / PBS-PU (Polyurethane) A
Double - Available in Polyester or Polyurethane Catalog No. PBD-PE (Polyester) / PBD-PU (Polyurethane) L
L
A
T
I
PUNCHED CHANNEL FRAMING O
N
S
• Available in Polyester and Vinyl Ester
resin types. 1"
39
DuroStrut CONNECTOR PLATES
• Based on individual applications, changes may be required on For Vinyl Ester Connector Plates, insert the letters “VE” as
dimension and thickness of material. indicated in this example:
Please consult factory. CP-100 (Polyester) CP-VE-100 (Vinyl Ester)
• Holes are drilled to accept 3/8" and 1/2" bolts.
15/8"
15/8"
D 45/8"
6" 7"
31/2"
U 10"
R 45/8"
45/8"
7"
31/2"
O
S
T
R CP-105 CP-109 CP-110 CP-111 CP-112
U
T
53/8"
53/8" 6"
• 31/2"
53/8"
31/2" 45/8" 53/8"
31/2"
S
T
R
31/2"
U 5" 41/2"
P
P 7"
7/8"
7/8"
O
R
CP-118 CP-119 CP-120 CP-205 CP-209
T
S 15/8"
Y 4" 31/4" 15/8"
S
15/8"
Universal Angle
T 21/4" CP-501
• Available in Polyester,
E 41/2"
CP-501 (Polyester)
M 15/8" Polyurethane (alternate to 51/4"
CP-PU-501 (Polyurethane)
S
7/8"
Vinyl Ester), and Nylon.
CP-NY-501 (Nylon)
CP-210 CP-211
4"
WINDOW CLAMP
4"
41/2" 11/2" (38)
4"
15/8" • Stainless Steel set screw included.
7/8"
7/8"
11/16"
23/4" (27)
CP-226 CP-405 (70)
Part No: WC-158
13/4"
4" (44)
(102)
31/2"
(89)
40
“NON-METALLIC” UNIVERSAL PIPE CLAMPS CONDUIT SWIVEL CLAMP
• For rigid, PVC coated steel, PVC Schedule 40 & 80 and fiberglass conduit.
• Made from a toughened grade of glass reinforced thermoplastic
polyester resin.
• Standard fasteners are nylon slotted hex bolt and nut. Recommended for
horizontal use as shown. For vertical placement please contact factory.
• Packaged twenty sets per bag.
• If stainless steel fasteners are preferred,
indicate by adding the letter “S”
after the catalog number
(Example: PC-1609S).
Hanger Allowable S
FIBERGLASS CLEVIS HANGERS Catalog Nominal Dimension Inches Rod Load U
No. Dia. In A B C In. Lbs. Hanger rod P
mounting hole P
• Vinyl Ester resin. CH-010 1 15/8 43/4 3 1/2 200 O
CH-015 11/2 21/8 55/8 33/8 1/2 200
R
• Allowable loads have a T
CH-020 2 21/2 7 43/8 1/2 200
3:1 safety factor at 120°F. CH-025 21/2 35/16 69/16 41/4 1/2 200 S
CH-030 3 33/4 71/2 41/4 1/2 300 Y
• Insulation may be required CH-040 4 51/8 93/4 57/8 1/2 400
A
B S
Max.
at higher temperatures. CH-060 6 73/16 123/8 8 1/2 600 Pipe T
OD
C
E
CH-080 8 93/8 159/16 101/4 1/2 600 M
• Tolerance is 3/4" maximum. CH-100 10 1119/32 147/8 1211/16 5/8 600 S
CH-120 12 135/8 221/4 14 5/8 600
CH-140 14 151/4 263/16 163/4 5/8 600
B C
SR1-24P SR1-24V 28 12 10 480
B
SR2-24P SR2-24V 26 21 15 750
SR2-30P SR2-30V 32 21 15 750
1" SR2-36P SR2-36V 38 21 15 750
1"
41
TYPICAL SUPPORT INSTALLATIONS
DuroStrut combined with Enduro cable tray accessories are functional in many non-cable tray applications.
DuroStrut includes all the items necessary to field fabricate to your specifications whether wall, floor, or
ceiling mounted. Enduro can also assist in engineering to your requirements.
If you need a special shape or assembly, call Enduro for information on custom pultrusions and fabrications.
S TYPICAL HANGING SUPPORT SYSTEM HOLD DOWN CLIP WITH SELF-LOCKING CHANNEL NUT
U
P
P
O Hex Nut
R Double Beam Clamp
T Flat Washer
DuroStrut
Fiberglass/Composite
Strut & Support Systems
42
DuroStrut LOADING INFORMATION - CHANNEL FRAMING Table 10
Beam and Column Data: Polyester and Vinyl Ester Resin Base
Beam Maximum Deflection
Span or Allowable @ Maximum Uniform Load Uniform Load Maximum
Column Uniform Allowable @ Maximum Deflection @ Maximum Deflection Allowable
Height Beam Load Uniform Beam Load = 0.25 In. (6mm) = 0.50 In. (13mm) Column Load
In. Catalog Poly Vinyl Poly Vinyl Poly Vinyl Poly Vinyl
(mm) No. Lbs. (kg) Lbs. (kg) In. (mm) In. (mm) Lbs. (kg) Lbs. (kg) Lbs. (kg) Lbs. (kg) Lbs. (kg)
12 EC-10 790 (358) 990 (449) 0.11 (3) 0.12 (3) • • • • • • • • 2550 (1156)
(305) EC-158 1720 (780) 2150 (975) 0.07 (2) 0.07 (2) • • • • • • • • 3650 (1655)
EC-158D 5080 (2301) 6350 (2880) 0.04 (1) 0.04 (1) • • • • • • • • 7300 (3111)
18 EC-10 530 (240) 670 (304) 0.24 (6) 0.27 (7) • • 620 (281) • • • • 2350 (1066)
(457) EC-158 1150 (521) 1440 (653) 0.15 (4) 0.17 (4) • • • • • • • • 3370 (1528)
EC-158D 5080 (2301) 4240 (1923) 0.09 (2) 0.10 (2) • • • • • • • • 6740 (3058)
EC-10 400 (181) 500 (227) 0.43 (11) 0.48 (12) 240 (109) 270 (122) • • • • 2070 (939)
D
24
EC-158 860 (390) 1080 (490) 0.27 (7) 0.30 (8) 810 (367) 910 (412) • • • • 2960 (1342) U
(610) R
EC-158D 2540 (1152) 3180 (1442) 0.16 (4) 0.17 (4) • • • • • • • • 5920 (2685)
EC-10
O
320 (145) 400 (181) 0.67 (17) 0.75 (19) 120 (54) 140 (63) 240 (109) 270 (122) 1710 (775)
30
EC-158 690 (313) 870 (394) 0.42 (11) 0.48 (12) 410 (186) 460 (209) • • • • 2450 (1111)
S
(762)
EC-158D 2040 (925) 2550 (1156) 0.24 (6) 0.27 (7) 2000 (907) 2350 (1066) • • • • 4900 (2222) T
R
EC-10 270 (122) 340 (154) 0.98 (25) 1.10 (28) 70 (31) 80 (36) 140 (63) 160 (72) 1260 (571)
36
EC-158
U
580 (263) 730 (331) 0.61 (15) 0.69 (19) 240 (109) 270 (122) 480 (217) 540 (245) 1800 (816)
(914)
EC-158D 1700 (771) 2130 (966) 0.35 (9) 0.39 (10) 1220 (553) 1370 (621) • • • • 3600 (1633)
T
42 EC-10 230 (104) 290 (131) 1.32 (34) 1.49 (38) 50 (22) 55 (25) 100 (45) 115 (52) 920 (417) •
(1067) EC-158 490 (222) 620 (281) 0.82 (21) 0.92 (23) 150 (68) 170 (77) 300 (136) 340 (154) 1320 (598)
EC-158D 1460 (662) 1830 (830) 0.48 (12) 0.62 (16) 770 (349) 870 (394) 1510 (650) 1720 (780) 2640 (1197)
T
48 EC-10 200 (91) 250 (113) 1.72 (44) 1.92 (49) 30 (13) 35 (16) 60 (27) 70 (31) 700 (317) E
(1219) EC-158 430 (195) 540 (245) 1.07 (27) 1.20 (30) 100 (45) 115 (52) 200 (90) 230 (104) 1010 (458) C
EC-158D 1270 (576) 1590 (721) 0.62 (16) 0.69 (17) 520 (236) 590 (267) 1040 (471) 1170 (530) 2020 (916) H
60 EC-10 160 (72) 200 (91) 2.68 (68) 2.99 (76) 20 (9) 23 (10) 40 (18) 45 (20) 180 (81) N
(1524) EC-158 350 (158) 400 (200) 1.70 (43) 1.91 (48) 60 (27) 70 (32) 120 (54) 135 (61) 260 (118) I
EC-158D 1020 (462) 1280 (580) 0.97 (25) 1.09 (28) 270 (122) 310 (140) 540 (245) 610 (276) 520 (235) C
72 EC-10 140 (63) 180 (81) * * * * 10 (4) 12 (5) 20 (9) 23 (10) • • A
(1829) EC-158 290 (131) 370 (168) 2.44 (62) 2.78 (71) 30 (13) 34 (15) 60 (27) 70 (32) • • L
EC-158D 850 (385) 1070 (485) 1.40 (35) 1.57 (40) 160 (72) 180 (81) 320 (145) 360 (163) • •
84 EC-10 120 (54) 150 (68) * * * * NR • • • 12 (5) 15 (7) • • D
(2134) EC-158 250 (113) 320 (145) * * * * 20 (9) 23 (10) 40 (18) 45 (20) • • A
EC-158D 730 (331) 920 (417) 1.91 (48) 2.15 (55) 100 (45) 115 (52) 200 (90) 230 (104) • • T
EC-10 100 (45) 130 (59) * * * * NR • • • • • • • • • A
96
(2438) EC-158 220 (100) 250 (113) * * * * 13 (6) 15 (7) 26 (12) 30 (13) • •
EC-158D 640 (290) 800 (363) 2.50 (63) 2.79 (71) 70 (32) 80 (36) 140 (63) 160 (72) • •
Beam Loads: Table lists the total allowable load for Column Loads: Table lists the total allowable axial Notes: All beams should be supported in a manner
various simple spans based on a minimum safety load for various unsupported column heights based to prevent rotation at supports. Long, deep beams
Loading Table factor 2:1. If load is concentrated at center of span, on a minimum safety factor of 3:1. Eccentric loads should be tied between supports to prevent twist.
Description multiply the load from the table by 0.5 and the should be reduced according to standard practice. * = Deflection is in excess of 3.00 In. (76mm);
corresponding deflection by 0.8. mid-span support is recommended.
NR = Not Recommended
43
DuroThread
INSTALLATION GUIDE
Cover
Metal and FRP Installation
When utilizing metal fasteners, connectors, or nuts, considera- Cable Tray
tion must be given to reduced strengths. DuroThread rod and Hold Down Clip
nuts are designed with maximum thread engagement and extra Channel Framing
nut thickness. Metal products have less thread engagement.
When installation requires metal components, special tests may Nut & Flat Washer
be necessary to define ultimate strengths of the fastener systems.
44
DuroThread FASTENER & HANGING SYSTEMS
BEAM CLAMPS
1"
Single Double
45
ComWay ™ LAY-IN WIREWAY SYSTEM
46
MODULAR DESIGN
Typical Catalog Number Prefixing
Enduro ComWay™ Lay-in- All ComWay™ sections
Wireway has a modular and fittings are available
design which includes: in five sizes (in inches): 21/2"
• Straight sections • 21/2 x 21/2 4" 4"
• Elbows • 4x4 21/2" 4" 12"
• Tees • 6x6
CW 250 CW 404 CW 412
• Crosses • 4 x 12
• 6 x 12
Inquire about
other available sizes.
6" 6"
The 6 x 12 (CW 612) is available with or without a
divider. The divider allows separation of various 6" 6" 6"
cables as needed.
CW 606 CW 612
C
E O
STRAIGHT SECTIONS M
1/8" 1/8" W
ALL ComWay STRAIGHT SECTIONS AND FITTINGS
™ A
Y
ARE PROVIDED WITH A “SNAP-ON/SNAP-OFF” COVER Pultruded FRP Wireway Cover
• Straight Sections and Covers come in 10 Ft. lengths. •
FRP Wireway Cover
• Note: Splice Plates are a separate order item. Splice Plate 3" Deep
Dimension Inches (mm) D L
Catalog
A
No. A B C D E
Y
CW 250 x 10 N/A 2.5 2.5 3 N/A*
CW 404 x 10 33/16 (81) 4 (102) 4 (102) 43/4 (121) 53/8 (136)
FRP I
Wireway N
B
A
CW 412 x 10 33/16 (81) 4 (102) 12 (305) 123/4 (324) 133/8 (340) Body
Splice
CW 606 x 10 55/8 (143) 6 (152) 6 (152) 63/4 (171) 73/8 (187) Plate W
CW 612 x 10 55/8 (143) 6 (152) 12 (305) 123/4 (324) 133/8 (340) I
C R
* Cover body and splice plates not available for CW250. See below for splicing method. E
W
A
COVER BODY & SPLICE PLATES CW 250 HOLD DOWN SPLICE JOINT Y
See illustration above for a
3"
Cover S
cut or elevation view. Body Y
S
Wireway T
Body
E
1.13 (29) M
.75 (19)
S
A
Splice
G
Plate
F
47
ComWay Fiberglass Lay-in-Wireway Fittings & Accessories
™
The Enduro ComWay™ Lay-in-Wireway has a modular design that includes the following fittings:
90° Direct Horizontal Bend 45° Direct Vertical Inside Bend Horizontal Tee Direct
90° Horizontal Bend 12" Radius 45° Vertical Inside Bend 12" Radius Horizontal Tee Direct 12" Radius
45° Direct Horizontal Bend 90° Direct Vertical Outside Bend Horizontal Cross Direct
45° Horizontal Bend 12" Radius 90° Vertical Outside Bend 12" Radius Horizontal Cross 12" Radius
90° Direct Vertical Inside Bend 45° Direct Vertical Outside Bend
90° Vertical Inside Bend 12" Radius 45° Vertical Outside Bend 12" Radius
L
A
Y Width Radius
Width 8"
I 203 mm A
N
Dimension Inches (mm) Dimension Inches (mm)
W Catalog No. A Catalog No. A L
I
R CW 250 - 90H 8 (203) CW 250 - 90H-12 221/2 (572) 3113/16 (808)
E CW 404 - 90H 1213/16 (325) CW 404 - 90H-12 2413/16 (630) 35 (889)
W CW 412 - 90H 21 (533) CW 412 - 90H-12 33 (838) 469/16 (1183)
A
Y CW 606 - 90H 15 (381) CW 606 - 90H-12 27 (686) 381/8 (968)
CW 612 - 90H 21 (533) CW 612 - 90H-12 33 (838) 469/16 (1183)
S
Y 45° DIRECT HORIZONTAL BEND 45° HORIZONTAL BEND 12" RADIUS
S
T Plan View
E Plan View
M W
id L
th
S
8"
203 mm
A
CW 250 - 45H 81/16 (205) CW 250 - 45H-12 59/16 (141) 257/8 (657)
CW 404 - 45H 101/2 (267) CW 404 - 45H-12 81/16 (205) 283/8 (721)
CW 412 - 45H 185/8 (473) CW 412 - 45H-12 163/16 (411) 349/16 (878)
CW 606 - 45H 125/8 (321) CW 606 - 45H-12 103/16 (259) 30 (762)
CW 612 - 45H 185/8 (473) CW 612 - 45H-12 163/16 (411) 349/16 (878)
48
LAY-IN WIREWAY ACCESSORIES
B
CW 404 - PA 101/4 (260) 103/8 (264) CW 250 - CP304
CW 412 - PA 181/4 (463) 103/8 (264) CW 404 - CP304
CW 606 - PA 121/4 (311) 123/8 (314) CW 412 - CP304
p
CW 612 - PA 181/4 (463) 123/8 (314) " Ty A CW 606 - CP304
11 /2
11/2" Typ
CW 612 - CP304
* Please contact factory.
90° DIRECT VERTICAL INSIDE BEND 90° VERTICAL INSIDE BEND 12" RADIUS
Depth C
Side View Side View O
M
W
A
8" L Y
203 mm
•
A
A
L
Depth
A
Y
Depth
I
Dimension Inches (mm) Dimension Inches (mm) N
Catalog No. A Catalog No. A L
W
CW 250 - 90IV 101/2 (267) CW 404 - 90IV-12 179/16 (446) 2413/16 (630) I
CW 404 - 90IV 12 (305) CW 404 - 90IV-12 181/8 (460) 2511/16 (652) R
CW 412 - 90IV 12 (305) CW 412 - 90IV-12 181/8 (460) 2511/16 (652)
E
W
CW 606 - 90IV 14 (356) CW 606 - 90IV-12 181/8 (460) 2511/16 (652) A
CW 612 - 90IV 14 (356) CW 612 - 90IV-12 181/8 (460) 2511/16 (652) Y
45° DIRECT VERTICAL INSIDE BEND 45° VERTICAL INSIDE BEND 12" RADIUS S
Y
S
T
L Side View E
Side View 8"
203 mm M
S
8"
203 mm
A
Depth
CW 250 - 45IV 81/16 (205) CW 250 - 45IV-12 101/8 (257) 211/16 (535)
CW 404 - 45IV 103/8 (264) CW 404 - 45IV-12 115/16 (287) 213/4 (552)
CW 412 - 45IV 103/8 (264) CW 412 - 45IV-12 115/16 (287) 213/4 (552)
CW 606 - 45IV 113/16 (284) CW 606 - 45IV-12 123/4 (324) 213/4 (552)
CW 612 - 45IV 113/16 (284) CW 612 - 45IV-12 123/4 (324) 213/4 (552)
49
90° DIRECT VERTICAL OUTSIDE BEND 90° VERTICAL OUTSIDE BEND 12" RADIUS
A
Depth
L
8"
A
203 mm
Depth
C CW 250 - 90OV 101/2 (267) CW 250 - 90OV-12 193/16 (487) 271/8 (689)
O CW 404 - 90OV 12 (305) CW 404 - 90OV-12 221/8 (562) 313/8 (797)
M CW 412 - 90OV 12 (305) CW 412 - 90OV-12 221/8 (562) 313/8 (797)
W CW 606 - 90OV 14 (356) CW 606 - 90OV-12 243/16 (614) 343/16 (868)
A CW 612 - 90OV 14 (356) CW 612 - 90OV-12 243/16 (614) 343/16 (868)
Y
• 45° DIRECT VERTICAL OUTSIDE BEND 45° VERTICAL OUTSIDE BEND 12" RADIUS
L
A
Y
Depth
L Side View
I
Depth
N
A
W Side View
A
I
R 8"
E 203 mm
W
A
Y Dimension Inches (mm) Dimension Inches (mm)
Catalog No. A Catalog No. A L
S
Y CW 250 - 45OV 81/16 (205) CW 250 - 45OV-12 915/16 (252) 213/8 (543)
S CW 404 - 45OV 10 (254) CW 404 - 45OV-12 12 (305) 237/16 (595)
T CW 412 - 45OV 10 (254) CW 412 - 45OV-12 12 (305) 237/16 (595)
E
M CW 606 - 45OV 12 (305) CW 606 - 45OV-12 14 (356) 25 (635)
S CW 612 - 45OV 12 (305) CW 612 - 45OV-12 14 (356) 25 (635)
50
HORIZONTAL TEE DIRECT HORIZONTAL TEE 12" RADIUS
Width
Width
A
A
8" 8"
203 mm 203 mm
Width
8" Radius Width Radius 8"
203 mm 203 mm
L
L
CW 250 - HT 101/2 (267) 181/2 (470) CW 250 - HT-12 221/2 (572) 421/4 (1073)
C
CW 404 - HT 13 (330) 205/8 (524) CW 404 - HT-12 2413/16 (630) 445/8 (1133)
O
CW 412 - HT 21 (533) 283/4 (730) CW 412 - HT-12 3215/16 (837) 523/4 (1340) M
CW 606 - HT 15 (381) 223/4 (578) CW 606 - HT-12 2615/16 (684) 463/4 (1187) W
CW 612 - HT 21 (533) 283/4 (730) CW 612 - HT-12 3215/16 (837) 523/4 (1340) A
Y
HORIZONTAL CROSS DIRECT HORIZONTAL CROSS 12" RADIUS •
203 mm
A
Y
Width
I
A
A
N
203 mm
W
8"
I
R
8" Width 8" 8" Radius Radius 8" E
203 mm 203 mm 203 mm Width 203 mm W
A A
A Y
Dimension Inches (mm) Dimension Inches (mm)
Catalog No. A Catalog No. A S
Y
CW 250 - HC 181/2 (470) CW 250 - HC-12 421/4 (1073) S
CW 404 - HC 205/8 (524) CW 404 - HC-12 445/8 (1133) T
CW 412 - HC 283/4 (730) CW 412 - HC-12 523/4 (1140) E
CW 606 - HC 223/4 (578) CW 606 - HC-12 463/4 (1187) M
CW 612 - HC-12 523/4 (1140) S
CW 612 - HC 283/4 (730)
PHYSICAL PROPERTIES
Polyester Polyester
Property Fire retardant ASTM Test Property Fire retardant ASTM Test
Longitudinal Direction Electrical
Ultimate Tensile Strength 30,000 PSI D638 Electric Strength, Short Term in Oil 1/8", VPM* 200 D149
Ultimate Compressive Strength 30,000 PSI D965 Electric Strength, Short Term in Oil, KV per inch 35
Ultimate Flexural Strength 30,000 PSI D790 Thermal
Transverse Direction Thermal Coefficient of Expansion (Inches/Inch/°F)** 5 x 10-6 D696
Ultimate Tensile Strength 7,000 PSI Other
Ultimate Compressive Strength 15,000 PSI Density – Solid Shape Lbs./In. 0.065 D792
Ultimate Flexural Strength 10,000 PSI Water Absorption (24 Hr. Immersion) Max % by Wt. 0.50 D570
Surface Burning Characteristic, Maximum 25 E84
* Specimen tested perpendicular to laminate face ** Indicates reported value measured in longitudinal direction
Meets and exceeds test standards for UL 94-VO Flammability Classification and has a flame spread rating under 25 when tested in accordance with ASTM E84.
51
Also from INSTRUMENT SUPPORTS
• Please specify dimensions in inches.
• The 2" SteelFree™ U-Bolt may be
used to attach instruments and/or
gauges to the supports.
StandFast ™
Floor Mount Column or
Single Wall Mount
Dim B
Fiberglass/Composite
Instrument & Pushbutton Stands
Dimension A
A universal instrument support
Dimension A
system that offers many of the Note:
Catalog No.: Catalog No.: Minimum is 11"
same features and benefits
as our cable tray, strut DISR170B1x(Dim. A) DISR175B48 x (Dim. A) x (Dim. B)
and wireway systems. Example: DISR170B148 Example: DISR175B48x11x12
Constructed from 2"
Schedule 80 gray vinyl DIM C
ester pipe with an 8"
gray square vinyl ester
O base. Available in a variety
Dim C
T
H of combinations to fit any Floor Mount Floor Mount
E mounting requirements. Double Multiple
Dimension A
R Delivered fully assembled, or DIMENSION A Instrument Dim B
available in component parts
P DIMENSION B
for field assembly.
R
O
D
U
C Catalog No.: Catalog No.:
T
S DISR171B x (Dim. A) x (Dim. B) x (Dim. C) DISR172B x (Dim. A) x (Dim. B) x (Dim. C)
Example: DISR171B48x36x18 Example: DISR172B36x12x15
• Made of pultruded fiberglass reinforced • Made from glass reinforced polyurethane resin,
vinyl ester 2" square tube with an U-Bolts are the ideal choice for mounting enclosures,
8" vinyl ester base. instrumentation, conduit, and piping on your D
52
Tuff Span ® FRP
Roofing and Siding
Enduro fiberglass (FRP) building panels have a long, successful
history of usage in industrial plants, offshore application, and
waste treatment facilities. Available as opaque or translucent,
the durable building panels provide outstanding corrosion
protection, superior structural performance, and (optional)
natural light transmission.
Tuff Span ®
Ventilation O
T
Components H
E
for Windwalls R
P
and Buildings R
O
Corrosion resistant fiberglass louvers and ridge vents far outlast wood, D
metal, and plastic louvers for industrial facilities and as wind walls on U
offshore platforms. C
T
S
Enduro FRP
Baffle Wall
Fiberglass Baffle Systems from Enduro Composites are pre-engineered
structural walls, composed of fiberglass reinforced plastic (FRP) panels,
angles, and columns. Specifically designed for submerged potable water
and waste treatment flow control, Enduro baffle systems offer advantages
over redwood, concrete, and stainless steel.
53
Tuff Span ® Fiberglass
Structural Shapes
Enduro offers standard and Tuff Span Standard Shapes include
custom shapes for challeng- fiberglass reinforced plastic channel,
ing, structural and environ- angle, tube, wide flange, and flat plate.
mental conditions. Delivering Enduro Composites furnishes these
long, maintenance-free ser- materials as individual structural com-
vice life, the structural sec- ponents and in assembled products.
tions are cost effective solu-
Tuff Span Flanged Box Beams are
tions for industrial buildings
developed specifically for long span
in corrosive environments.
conditions required in building structures and support of tank
The sections are manufac- cover decking. The 8F6 and 18F17 custom design optimizes
tured by advanced pultrusion structural properties and cost through innovative use of shape,
process that provides opti- glass fiber reinforcing, and manufacturing process. The box shape
mum strength and stiffness, increases lateral stability and eliminates the need for bridging or
consistent properties, close lateral bracing. Within the material, continuous glass fiber rein-
tolerances, and good surface finish. Enduro’s pultrusion process forcements are aligned in multiple directions and are placed in
O
T produces consistent, reliable quality and glass fiber reinforce- greater quantity at flanges as well as upper and lower web areas.
H ments up to 60% of the material weight. This design produces higher structural properties per weight as
E compared to unidirectional reinforced FRP Wide Flange and
R The material’s premium grade, isophthalic polyester or vinyl
I-Beam sections.
resin system provides outstanding corrosion protection and is fire
P retardant with a flame spread rating of 25 or less. The resulting For technical data and catalog on Tuff Span Fiberglass
R combination of corrosion resistance, non-conductivity, and long Structural Shapes, please contact Enduro.
O span capability delivers significant end user benefits and life
D
U cost savings.
C
T • Stocking lengths are 10 Ft. or 20 Ft.
S TUFF SPAN® STRUCTURAL • Flat sheet is available in 3' x 10' pieces.
SHAPES and FLAT SHEETS • Contact factory for required shapes not listed.
• Available in Polyester and Vinyl Ester.
Size in Inches Lbs./Ft. Size in Inches Lbs./Ft. Size in Inches Lbs./Ft. Size in Inches Lbs./Ft. Size in Inches Lbs./Ft.
Tuff Span ®
FRP Buildings
Enduro provides design assistance and supply of
pre-engineered buildings that consist entirely of
corrosion resistant FRP wall, roof, and structural
components.
54
Third Rail FRP Coverboard
Non-Conductive Safety for Light Rail Application
Enduro’s Third Rail Coverboard Systems are cus-
tom designed to provide safety by shielding or insu-
lating personnel from a rail that is “live”or may
contain stray currents. Enduro coverboards are
made of high performance, lightweight
pultruded composites which, if necessary, can allow
personnel or riders to more safely exit in an emer-
gency. Enduro has exceeded the most stringent of
transportation safety tests utilizing our Low Smoke O
T
/ Non-Toxic resin technology that provides the H
highly desired low smoke development and low E
R
smoke toxicity characteristics preferred by trans-
portation safety authorities. P
R
11.22" (281)
O
Enduro coverboard products have been utilized by multiple transit D
authorities, domestically and internationally, and are specifically U
R 6.19"(155) C
designed to meet each customer’s special requirements. Please T
4.04"
S
contact Enduro to find out more
(101)
4.57" (116)
can help you develop a new or
6.13"
improved design to fit your needs. .79"
(20) 2.42"
(61.4)
(153)
.96"
(24.5) .20 (5)
55
Delivering unmatched quality, service, and
value, Enduro FRP Electrical Products are
used in a broad range of applications:
■ Ladder Type Cable Tray Systems
■ Channel Type Instrumentation Tray Systems
■ Lay-In Wireway Systems
■ Instrument Support Stands
■ Strut Channel Framing and Accessories
■ Third Rail Coverboard
■ Fasteners and Hanging Systems
Information on Enduro’s engineered, FRP materials is available from our staff of technical
specialists and website: www.endurocomposites.com
Represented by: