Professional Documents
Culture Documents
2.1 INTRODUCTION
Wood fiber and polymer composites (WFPC) are normally produced by mixing
wood fiber with polymer, or by adding wood fiber as filler in a polymer matrix, and
pressing or molding under high pressure and temperature. Most polymers, especially
thermoplastics, are non-polar (hydrophobic) substances, which are not compatible with
polar (hydrophilic) wood fibers and, therefore, poor adhesion between polymer and wood
fiber in WFPC can result (Geottler 1983; Klason et al. 1984). In order to improve the
affinity and adhesion between wood fibers and thermoplastic matrices in production,
chemical coupling agents have been employed (Chun and Woodhams 1984; Woodhams
et al. 1984; Dalväg et al. 1985; Schneider and Brebner 1985). Coupling agents are
substances that are used in small quantities to treat a surface so that bonding occurs
between it and other surfaces, e.g., wood and thermoplastics (Pritchard 1998).
active agents), including compatibilizers and dispersing agents (Štepek and Daoust 1983;
Radian Corporation 1987; Clint 1998). Bonding agents act as bridges that link wood
fibers and thermoplastic polymers by one or more of the following mechanisms: covalent
bonding, polymer chain entanglement, and strong secondary interactions as in the case of
*Reprinted in part with permission from Wood Fiber and Science, 2000, Vol. 32, No. 1,
Pages 88-104; J. Z. Lu; Q. Wu; and H. S. McNabb, Jr.; Chemical Coupling in Wood
Fiber and Polymer Composites: A Review of Coupling Agents and Treatments. Society
of Wood Science and Technology State-of-the-Art-Review. Copyright 2000 by the
Society of Wood Science and Technology.
11
hydrogen bonding (Raj et al. 1988; Maldas et al. 1989a). Compatibilizers are used to
interfacial tension (Pritchard 1998). Some compatibilizers, such as acetic anhydride and
methyl isocyanate, are monofunctional reactants. They lower the surface energy of the
fiber, and make it non-polar, more similar to the plastic matrix. Some bonding agents,
(Oksman and Lindberg 1998; Oksman et al. 1998; Simonsen et al. 1998). Dispersing
agents reduce the interfacial energy at the wood fiber-matrix interface to help uniform
dispersion of wood fiber in a polymer matrix without aggregation and thereby facilitate
the formation of new interfaces (Rosen 1978; Porter 1994). For example, stearic acid and
its metallic salts are used to improve the dispersibility of wood fibers in the matrix. In
general, compatibilizers and dispersing agents do not form strong adhesion at the fiber-
matrix interface (Štepek and Daoust 1983). Thus, a functional distinction between
bonding agents, compatibilizers, and dispersing agents should be noticed. In this paper,
however, all bonding agents and surfactants are lumped together as coupling agents for
coating and graft co-polymerization) and mixing processes for improving mechanical
properties of WFPC have been introduced. For example, Youngquist and colleagues
(Krzysik et al. 1990; Krzysik and Youngquist 1991) conducted successful experiments on
coupling agent. They developed an excellent coating method to spray the emulsified
12
Epolene E-43 on wood fiber before formation. As a result of these efforts, WFPC have
Hamed and Coran 1978; Meyer 1981, 1982, 1984; Rowell and Konkol 1987; Schneider
1994; Youngquist 1995). These reviews cover from chemical modification and treatment
of wood and plastics to production technologies and applications for various types of
coupling agents and treatments currently used in this field. The objective of this work is
polymer, and mixing technology for the manufacture of WFPC. The adhesion mechanism
publications.
onto wood fiber with a catalyst system containing ferrous cations and hydrogen peroxide
to modify the compatibility between wood fiber and thermoplastic polymer. This method
was further developed by other researchers (Gulina et al. 1965; Faessinger and Conte
1967; Dimov and Pavlov 1969; Kokta and Valade 1972; Hornof et al. 1976). Meyer
(1968) was possibly the first person who suggested using a coupling agent (which he
13
combine cellulose and polyethylene (PE) or polyvinyl chloride (PVC) in the presence of
However, little attention had been paid to the applications of coupling agents in
WFPC until the 1980s. From 1980 to 1985, a series of patents was issued for the
application of isocyanate and MA coupling agents in WFPC (Coran and Patel 1982;
Geottler 1983; Nakamura et al. 1983; Woodhams 1984). Xanthos (1983) introduced γ-
or PDM) as coupling agents to improve the mechanical properties of wood flour and
polypropylene composites. Some coupling agents, such as silane A-174 and propylene
oxide (PO), were also applied in wood and plastic composites (WPC) to improve their
dimensional stability (Rowell et al. 1976; Rowell and Ellis 1978; Schneider and Brebner
1985).
coworkers made an initial study on using MA as the coupling agent in the cellulose flour
and polypropylene (PP) composites (Dalväg et al. 1985). Woodhams et al. (1984)
coupling agent in thermomechanical pulp (TMP) and isotactic PP composites. These two
articles have been the important references for the research on chemical coupling in
WFPC.
agent in melt-blended composites. Kokta (1988) patented PMPPIC for cellulose fiber and
14
PE composites. In Japan, the Shiraishi group focused on the application of MAPP with
high-molecular weight (Kishi et al. 1988; Han et al. 1989). In the United States and
Sweden, much work has been done on the application of MAPP and other coupling
agents in the melt-blending process, such as injection molding, extrusion, and transfer
molding (Myers et al. 1990, 1991, 1993; Olsen 1991; Liang et al. 1994; Gatenholm et al.
1995).
Over forty coupling agents have been used in WFPC (Table 2.1). Coupling agents
are classified into organic, inorganic, and organic-inorganic groups. Organic agents
organic acids, monomers, polymers, and copolymers. Only a few inorganic coupling
agents, such as silicates, are used in WFPC. Organic-inorganic agents include silanes and
titanates.
[-(CO)2 O-] of maleic anhydrides, and (-Cl-) of diclorotriazine derivatives, interact with
the polar groups [mainly hydroxyl groups (-OH)] of cellulose and lignin to form covalent
or hydrogen bonding (Zadorecki and Flodin 1985; Raj et al. 1988; Maldas et al. 1989a;
Raj and Kokta 1991; Chtourou et al. 1992). Alternatively, organic coupling agents can
modify the polymer matrix by graft copolymerization, thus resulting in strong adhesion,
surface polarity of wood fiber and improve the compatibility between wood fiber and
15
Table 2.1. Coupling agents used in WFPC.
Coupling Agent Additive a Reference
Organic agents
1. Acrylates
N,N′-m-Phenylene bismaleicimide (BMI) DCP Xanthos 1983; Sain and Kokta 1994
3. Anhydrides
5. Epoxides
Butylene oxide (BO) – Rowell et al. 1982
Propylene oxide (PO) – Rowell et al. 1982
6. Isocyanates
Ethyl isocyanate (EIC) – Raj et al. 1988; Maldas and Kokta 1991b
Hexamethylene diisocyanate (HMDIC) – Raj et al. 1988; Maldas and Kokta 1991b;
Gatenholm et al. 1992
Poly[ehtylene(polyphenyl isocayanate)] (PEPPIC) – Selke et al. 1990
Poly[methylene(polyphenyl isocyanate)] (PMPPIC) DCP Maldas et al. 1989a, b; Maldas and Kokta
1989, 1990a, b, 1991a; Raj et al. 1988
Toluene 2,4-diisocyanate (TDIC) – Raj et al. 1988; Kokta et al. 1990a
7. Organic acids
8. Monomers
a
BPO-benzoyl peroxide; DCP- dicumyl peroxide; LPO- lauroyl peroxide; TBPB- tert-butyl peroxide
benzonate, DTBPO- di-tert-butyl peroxide.
16
Table 2.1. Continued.
Coupling Agent a Reference
Additive
Epoxylpropyl mechacrylate (EPMA) CS2/H2O2/Fe2+ 1981; Ellwood et al. 1972; Maldas et al.
Methacrylic acid (MAA) or 1988, 1989a; Maldas and Kokta 1990d;
Methyl methacrylate (MMA) N2/H2O2/(CH3)2SO4 Daneault et al. 1989; Chen et al. 1995
Styrene or
Vinyl compounds K2S2O5/H2O2
Inorganic agents
Organic-inorganic agents
1. Silanes
Vinyltri(2-methoxyethoxy) silane (A-172) CCl4, DCP Beshay et al. 1985; Maldas et al. 1988, 1989a;
Raj et al. 1989, 1990; Kokta et al. 1990c
γ-Methacryloxypropyltrimethoxy silane (A-174) CCl4, DCP, Xanthos 1983; Beshay et al. 1985; Bataille et
CH3OH al. 1989; Maldas et al. 1989a; Raj et al.
1988, 1989; Kokta et al. 1990c
β-(3,4-Epoxy cyclohexyl)ethyltrimethoxy silane LPO or DTBPO Kokta et al. 1990c
(A-186)
γ-Glycidoxy propyltrimethoxy silane (A-187) LPO or DTBPO Kokta et al. 1990c
γ-Aminopropyltriethoxy silane (A-1100) DCP or BPO, Maldas et al. 1988, 1989a; Bataille et al. 1989;
MA, p-xylene Raj et al. 1989; Kokta et al. 1990c
2. Titanates
a
BPO- benzoyl peroxide; DCP- dicumyl peroxide; LPO- lauroyl peroxide; TBPB- tert-butyl peroxide
benzonate, DTBPO- di-tert-butyl peroxide.
17
polymer (Dalväg et al. 1985; Maldas and Kokta 1990a, b). Organic-inorganic agents are
hybrid compounds in structure. For example, titanates usually contain a titanium center
and an organic part surrounding this inorganic atom. The functionality of the organic part
Anhydrides such as MA, AA, SA and PHA are popular coupling agents in WFPC.
AA, SA and PHA have two functional groups, i.e., carboxylate groups (-COO-), which
unsaturated carbonyl compound, containing one carbon-carbon double bond (C=C) and
two carboxylate groups (-COO-). This conjugated structure greatly increases the graft
reactivity of the carbon-carbon double bond on the heterocyclic ring with the polymer
matrix through the conjugate addition under a radical initiator (Morrison and Boyd
molecular chain of MA is much shorter than that of polymer matrix and wood fibers.
This discrete nature makes MA not so effective to improve the interfacial adhesion
(Maldas et al. 1988, Maldas and Kokta 1990d). Accordingly, MA is usually used to
modify the polymer matrix by graft copolymerization. The formed copolymers, e.g.,
MAPE, MAPP, SEBS-MA and SMA, are used as coupling agents (Raj et al. 1990; Olsen
1991; Sanadi et al. 1992; Sain et al. 1993; Hedenberg and Gatenholm 1995; Oksman et
Isocyanate links wood fiber through the urethane structure (or a carbamate),
which is more stable to hydrolysis than esterification (John 1982; Maldas and Kokta
The delocalized π-electrons of the benzene rings in PMPPIC and TDIC lead to the
stronger interaction with PS and other polymer matrices compared with HMDIC and EIC
without π -electrons. Moreover, the cellulose phase and the polymer phase (PS or PVC)
are continuously linked by PMPPIC at the interface, while the discrete nature of TDIC,
HMDIC and EIC makes them inferior in this respect (Maldas et al. 1988). A comparison
composites with PMPPIC as a coupling agent had the highest tensile strength, compared
with those made with other types of coupling agents. Thus, PMPPIC is the best coupling
agent in these isocyanates, while TDIC has better coupling effectiveness than HMDIC
and EIC.
coupling agents recently used in WFPC, because the attachment of silanes to hydroxy
groups of cellulose or lignin is accomplished either directly to the alkoxy group (-OR′)
attached to silicon or via its hydrolyzed products (i.e. silanol) by the hydrogen bonds or
ether linkage (Kokta et al. 1990c). The functional group (R-) in silanes also influences
the coupling action. Silane A-172 and A-174 both contain a vinyl group; silane A-186
and A-187, an epoxy group; while silane A-1100, an amino group. When in contact with
PVC, polar methacryloxy groups in silane A-174 form a polar chain that is more
hydrophilic than that of A-172, resulting in poor adhesion. But for other matrices, the α,
β-unsaturated carbonyl structure of acrylic groups in A-174 may help form strong
adhesion, even crosslinking, at the interface. Silane A-186 and A-187 with an epoxy
19
35
10% CTM P and 90% PVC
30% CTM P and 70% PVC
30 PM PPIC
TDIC
15
10
0
1 2 3 4 5
Composite Type
Figure 2.1. Comparison of coupling effectiveness for different isocyanate coupling agents
in PVC and CTMP (aspen) composites (plot made with test data published by Kokta et
al. 1990a). Coupling agent used was: 1- PMPPIC, 2- TDIC, 3- HMDIC, 4- EIC, and 5-
no coupling agent (control). Concentration of coupling agents was 0.5% based on weight
of the polymer matrix.
20
group link cellulose and lignin by ether linkages, whereas NH2 groups of A-1100 offer
structure. These groups have different functions in the coupling reaction (Zadorecki and
Flodin 1985). On the heterocyclic ring, the reactive chlorines react with the hydroxyl
group (-OH) of wood fiber and give rise to the ether linkage between the cellulose phase
and the coupling agent. The electronegative nitrogen may link the hydroxyl group
through hydrogen bonding. On the alkyl chain, the carbon-carbon double bonds (C=C)
form covalent bonds with the polymer matrix by grafting. At the same time, the
electronegative nitrogen in the amino groups and oxygen in the carboxylate groups also
WFPC (Coran and Patel 1982; Hua et al. 1987; Simonsen and Rials 1992, 1996). PF and
DMM resins can crosslink wood fibers with the methylene (-CH2-) linkage resulting from
the condensation reaction between their reactive methylol groups (-CH2OH) and the
hydroxyl groups (-OH) of wood fiber. Although these methylol groups can not react with
the thermoplastic matrix, PF and DMM improve the interfacial adhesion through
molecular entanglement with the matrix (Simonsen and Rials 1992, 1996).
Similar to MA, acrylic acids and methacrylates (e.g., MAA, MMA, EPMA, and
GMA) also contain the α, β-unsaturated carbonyl structure, which may lead to
crosslinking or strong interfacial adhesion. Organic acids such as abietic acid (ABAC)
and linoleic acid (LAC) contain dienes and carboxylate groups in their molecular
21
structure, which are helpful to form strong adhesion in the interfacial region. In addition,
the reactive allylic group (-CH2-) in LAC might graft to the polymer matrix (Kokta et al.
1990b). Lacking chemical bonding at the interface, KR 138S and Na2SiO3 perform
poorly in WFPC (Dalväg et al. 1985; Maldas and Kokta 1990a, b). Na2SiO3 is usually
applied before mixing to increase the mechanical properties of WFPC. There are two
pretreatment methods: 1) coating coupling agents on wood fiber, and 2) modifying wood
The compatibility between wood fiber and polymer is enhanced by coating wood
fibers with coupling agents. This process can either cause the polar hydroxyl groups
(-OH) of wood fibers to react with coupling agents (such as PMPPIC), which have a
linear molecular structure similar to the polymer matrix, or create a chemical interaction
between coupling agents (such as MA) and the matrix (Maldas et al. 1989a; Kokta et al.
1990a).
coupling agents at high temperature with wood fibers and polymers in an extruder
(Dalväg et al. 1985; Myers et al. 1991). This method is mostly used in the melt-blending
process. For the blending method, a coupling agent is coated on the surface of wood
fiber, polymer or both in a roll mill or a magnetic stirrer at low or high temperature
22
(Maldas et al. 1988). For the soaking method, wood fiber (such as cellulose fiber) can be
first impregnated in the form of sheets of paper with a coupling agent solution containing
initiators or other additives. Then the impregnated paper is removed from the solution
and placed between two pieces of polymer release film for molding (Zadorecki and
Flodin 1985; Sanadi et al. 1992). In the spraying process, coupling agents are emulsified
and sprayed on to the surface of wood fibers (Krzysik et al. 1990; Krzysik and
Youngquist 1991). Both blending and spraying are suitable for the precoating of wood
fiber and polymer before mixing. Spraying and soaking are better than compounding and
blending for coating processes because coupling agents are distributed at the interface
more evenly and efficiently in the former two cases. However, it is difficult to accurately
control the impregnating amount of coupling agents for the soaking method.
polymer matrix to the wood surface to form a non-polar copolymer or modify the polarity
of the polymer matrix by grafting it with polar monomers to form a graft copolymer. This
results in the improvement of the interfacial adhesion. Recently, several graft methods
In the xanthation process, wood fibers are first kept under carbon disulfide (CS2)
fibers are then mixed with monomers, such as styrene, butyl acrylate, or epoxy
compounds, to form graft copolymers (Maldas et al. 1988, 1989a; Maldas and Kokta
23
1990d; Daneault et al. 1989). This method has been widely used for pretreating wood
fiber in WFPC.
high-energy radiation sources (such as beta (β) and gamma (γ) rays) with or without a
free radical catalyst. For example, the polymerization of vinyl or styrene monomers with
wood components was generated by using Cobalt-60 (60Co) gamma radiation (Kenaga et
al. 1962; Kent et al. 1962; Ramalingam et al. 1963; Meyer 1965, 1981, 1984; Ellwood et
al. 1972). Usually, at least 500,000 to 1,000,000 curies of Cobalt-60 are required for a
presence of a free radical initiator. It is then grafted on to wood fibers by a succinic half-
ester bridge (Gaylord 1972; Chun and Woodhams 1984; De Vito et al. 1984; Kishi et al.
1988; Maldas and Kokta 1990d). Besides the graft application of MA in the PS matrix
(Maldas and Kokta 1990d, 1991b), MA can modify PE, PP, and SEBS to form graft
for WFPC (Gaylord 1972; Chun and Woodhams 1984; Olsen 1991; Maldas and Kokta
1994). As mentioned before, two kinds of MAPP are used in WFPC. One is the MAPP
with a high-molecular weight (MW>30,000) (Kishi et al. 1988; Han et al. 1989; Takase
and Shiraishi 1989), such as 63H, 13H, and Hercoprime G (Olsen 1991; Gatenholm et al.
1992). The other type, such as Epolene E-43 (or 47L) and 15L, has a low-molecular
weight (MW<20,000) (Woodhams et al. 1984; Olsen 1991; Myers et al. 1990, 1991,
1993). Maleated polymers are usually coated on to wood fiber before mixing.
24
The acid number, which represents the amount of functionality in a coupling
agent, and molecular weight are two important properties influencing the coupling
effectiveness of MAPP in WFPC (Olsen 1991). Generally, MAPP with a high molecular
weight and high acid number effectively improves the mechanical properties of WFPC. It
was suggested that the Epolene E-43 probably acts as a dispersing agent instead of a true
coupling agent in melt-blending formation because of its low molecular weight (Wegner
et al. 1992). Krzysik and coworkers (Krzysik et al. 1990; Krzysik and Youngquist 1991),
however, reported that Epolene E-43 greatly improved the bonding of air-formed wood
Methacrylates can be used in graft reactions. For example, GMA and HEMA
have been used to modify wood fiber and polymer (Maldas et al. 1989a; Takase and
Shiraishi 1989). In a previous study, RGP was pretreated with an acetylating agent
containing AA before mixing with MAPP (Kishi et al. 1988). For WPC, some epoxides
[e.g., propylene oxide (PO) or butylene oxide (BO)] are grafted onto the cell wall before
the impregnation of MMA into the cell lumen (Rowell et al. 1982). Other coupling
agents, such as BMI (or PDM) and SA, are also applied in the graft copolymerization for
PP matrix and TMP (Rozman et al. 1994; Sain and Kokta 1994).
Based on the coating and grafting methods in WFPC, coupling treatments are
generally divided into three basic processes (Figure 2.2). Coupling agents can be directly
coated on wood fiber and polymer during mixing (Woodhams et al. 1984; Takase and
Shiraishi 1989; Maldas et al. 1989a; Myers et al. 1991). This process (one-step process)
25
is quite simple and cheap (Figure 2.2a). In the two-step process, coating or grafting is
carried out before mixing (Figure 2.2b, c). Coupling agents are coated or grafted on the
surface of wood fiber, polymer or both before mixing in the second process (Maldas et al.
1988; Krzysik et al. 1990; Maldas and Kokta 1990d; Krzysik and Youngquist 1991). In
the third process, part of the polymer and wood fiber furnish is treated with a coupling
agent, then mixed with untreated wood fiber and polymer (Maldas et al. 1989b; Kokta et
al. 1990a). In the two-step process, the resulting mixtures are usually ground to mesh size
20 for melt-blending formation (Maldas et al. 1988, 1989b; Maldas and Kokta 1989,
1990a). All three processes are suitable for melt-blended composites. The second process
It has been suggested that a two-step process is better than a one-step process
(Štepek and Daoust 1983). In the former case, less coupling agent and less mixing time
are required to obtain good adhesion between wood fibers and polymers. Moreover, the
two-step process helps increase the interface area (De Ruvo and Alfthan 1978; Maldas et
Coupling agents usually account for 2-8% by weight of wood fibers for melt-
blending formation (wood fiber-to-matrix weight ratio is 50:50); and 1-4% for air-
forming processes (wood fiber-to-matrix weight ratio is 70:30) (Maldas et al. 1989a, b;
Krzysik et al. 1990; Krzysik and Youngquist 1991; Myers et al. 1991, 1993).
Accordingly, a coupling agent accounts for only 1-3% of the total weight of a composite
in WFPC. The mixing ratios of coupling agents, wood fibers, and thermoplastic polymers
Polymer Mixing
a)
Coupling
agent
Wood
fiber
b) Pretreatment:
Polymer Mixing
Coating or grafting
Coupling
agent
Wood
fiber
Polymer Pretreatment:
Grinding
Coating or grafting
c) Coupling
Mixing
agent
Wood
fiber
Polymer
Figure 2.2. Three basic coupling treatments in WFPC: a) directly coating during mixing,
b) and c) pretreating before mixing. In (a) wood fiber, polymer, or both is coated or
grafted with a coupling agent, but in (c) only part of fiber and polymer is pretreated by a
coupling agent, then mixed with untreated fiber and polymer.
27
The concentration of coupling agents determines the coupling effectiveness in the
coupling agent (e.g., PMPPIC, MA, PHA, and MAPP) up to a certain limit, and then
decline or level off at higher concentrations (Figure 2.3). The reason that higher coupling
agent concentrations result in lower mechanical properties of the composite possibly lies
ungrafting coupling agents, and 3) interference with coupling reaction (John 1982;
Beshay et al. 1985; Maldas et al. 1989a; Maldas and Kokta 1990d, 1991a, b).
2.4.3 Additives
Initiators are usually required with coupling agents during the coupling treatment,
especially in graft copolymerization. The most widely used initiators are organic
peroxides, including dicumyl peroxide (DCP), benzoyl peroxide (BPO), lauroyl peroxide
(LPO), tert-butyl peroxy benzonate (TBPB) and di-tert-butyl peroxide (DTBPO) (Table
2.1). DCP is usually used with BMI, MAPP, PMPPIC, and silanes; and BPO with MA,
SA, silane A-1100, and chlorotriazines. TBPB is used as a free radical initiator of MA
and acrylates. LPO and DTBPO can be used in the silane coupling agents. In graft
peroxide may adversely affect the mechanical properties of the composite because
molecular chain scission of the polymer and cellulose occurs when peroxide is too
abundant (Maldas and Kokta 1991a). DCP has also been found to be a better initiator for
28
Table 2.2. Optimum ratios of coupling agent, polymer and wood fiber in WFPC a.
Coating and
Polymer Wood fiber Coupling mixing Fabrication Reference
agent b temperature c method
PP WF MAPP - injection Dalväg et al. 1985
70% 30% 6% molding
PS685D CTMP (aspen) A-172, A-174 145-225oC Carver press Maldas et al. 1989a
70% 30% 4% (70-75 C)
PS201 CTMP (75% black PMPPIC 175oC Carver press Maldas et al. 1989b
70-80% spruce +20% balsam 8% (175oC)
+5% aspen)
20-30%
PS201 CTMP (aspen) PHA 175oC molding Maldas and Kokta 1989,
65% 35% 10% 1990c
PVC CTMP (aspen) PMPPIC 145-150oC Carver press Kokta et al. 1990a
70-80% 20-30% 1-5%
a
RT- room temperature, PP-polypropylene, PS-polystyrene, PVC-polyvinyl chloride, HDPE-high density
polypropylene, WF-wood fiber, TMP- thermomechanical pulp, CTMP- chemithermomechanical pulp,
RGP- refiner ground pulp, A-172-vinyltri(2-methoxyethoxy) silane, A-174-γ-methacryloxy-
propyltrimethoxy silane, MAPP-maleated polypropylene, PHA-phthalic anhydride, PMAA-
polymethacrylic acid, and PMPPIC-poly[methylene(polyphenyl isocyanate)].
b
By weight of wood fiber.
c
Values in the parentheses are coating temperature.
MA compared with BPO because the free radicals of DCP have superior thermal stability
that leads to better graft performance (Maldas and Kokta 1991c). The free-radical
radiation for graft reaction of styrene and vinyl monomers (Meyer 1981).
29
50
45 2. PS201+CTMP
1. PP+RGP
40
35
25 4. PS525+CTMP
20
15 Coupling Agnets:
MAPP (1)
10 PMPPIC (2)
PMPPIC (3)
5 PHA (4)
a)
0
0 2 4 6 8 10 12 14 16
Concentration of Coupling Agent (%)
70
60 2. PS201+CTM P
50
Fracture Energy (m J)
40
30 4. PS525+CTM P
3. PVC +CTM P
20
10
b)
0
0 2 4 6 8 10 12 14 16
Concentration of Coupling Agent (% )
30
Organic solvents may be required with certain coupling agents. For example,
carbon tetrachloride (CCl4) is used in silanes A-172 and A-174 (Maldas et al. 1989a;
Maldas and Kokta 1990c), while methylene dichloride (CH2Cl2) is a solvent of titanate
coupling agents such as KR 138S (Dalväg et al. 1985). Other solvents include xylene,
pyridine, methanol, and ethanol (Xanthos 1983; Hau et al. 1987; Han et al. 1989, Myers
et al. 1990, 1991; Gatenholm et al. 1993; Simonsen and Rials 1996).
processing aids are also added to the blends to improve the physical and mechanical
(MgO), boric acid (H2B4O7), or borax (Na2B4O7) provides flame retardation to the
composite (Kishi et al. 1988; Han et al. 1989; Maldas and Kokta 1991a; Sain et al. 1993).
The addition of magnesium oxide and boron compounds can protect wood fiber from
(Han et al. 1989; Sain et al. 1993). In addition, adding a moderate amount of MgO can
improve the performance of MA because MgO reacts with water and the acid group to
yield carboxylate ions (-COO-). Concurrently, Mg2+ interacts with two carboxylate ions
as a crosslinking agent and yields ionomer systems (Han et al. 1989). Organic additives
primarily used in coupling treatments are dioctyl phthalte (DOP), barium acetate (BaAc),
Irganox-1010, Ionol, mono- and diglycerides of fatty acids (GMS), and distearyl
thiodipropionate (DSTP) (Han et al. 1989; Krzysik et al. 1990; Myers et al. 1991).
Mixing conditions, i.e. temperature, time, and rotation speed, directly influence
the coating quality and coupling agent performance (Takase and Shiraishi 1989; Maldas
31
and Kokta 1990d; Chen et al. 1995). Usually, mixing temperature is controlled at less
than 200°C for most coupling treatments to avoid decomposition and degradation of
wood fibers and some thermoplastic matrices (Woodhams et al. 1984; Maldas et al.
1989a; Takase and Shiraishi 1989; Myers et al. 1993). For refiner ground pulp (RGP) and
temperature of 180ºC and a rotation speed of 50 rpm (Takase and Shiraishi 1989).
Maldas and Kokta (1990d) reported that the maximum improvement in mechanical
when the mixing time was 15 min at 175ºC. For melt-blended composites, the blends are
required to re-mix 5-10 times (about 6-8 min) during compounding to achieve a better
distribution of coupling agents at the interface, when directly mixing coupling agents
with polymer and wood fiber (Maldas et al. 1989a; Maldas and Kokta 1990a, b, c).
Rotation speed has similar influence on the coupling effectiveness as does mixing time. It
was reported that moderate mixing speeds were preferred for better fiber length
2.5 CONCLUSIONS
and adhesion between polar wood fibers and non-polar polymer matrices. So far, more
than forty coupling agents have been used in production and research. Organic coupling
agents are better than inorganic coupling agents, because stronger adhesion is produced
at the interface. Although a number of coupling agents are used or have been tested in
production and research, the most popular are isocyanates, anhydrides, silanes, and
by compounding, blending, soaking, spraying, or other coating methods. There are three
basic mixing processes in production and research. Coupling agents can be directly
mixed with wood fiber and polymer in the melt-blending formation, such as injection
molding, extrusion, and transfer molding. They can also be coated or grafted on the
surface of wood fiber, polymer, or both. Then the pretreated and untreated wood fiber
and polymer are kneaded. Usually, pretreatment of wood fiber and polymer by coating or
concentration and chemical structure of coupling agents, choice of wood fiber and matrix
(e.g. shape, size and species), ratio of wood fiber to total matrix weight, formation
methods, and end-use requirements of the finished product. Future publications in this
series will discuss the adhesion mechanism and coupling performance of different
coupling agents.
2.6 REFERENCES
Bataille, P., L. Ricard, and S. Sapieha. 1989. Effects of cellulose fibers in polypropylene
composites. Polym. Comp. 10(2): 103-108.
Beshay, A. D., B. V. Kokta, and C. Daneault. 1985. Use of wood fibers in thermoplastic
composites II: Polyethylene. Polym. Comp. 6(4): 261-271.
33
Chun, I., and R. T. Woodhams. 1984. Use of processing aids and coupling agents in
mica-reinforced polypropylene. Polym. Comp. 5(4): 250-257.
Dalväg, H., C. Klason, and H. –E. Strömvall. 1985. The efficiency of cellulosic fillers in
common thermoplastics. Part II. Filling with processing aids and coupling agents.
Intern. J. Polymeric Mater. 11: 9-38.
Danuealt, C., B. V. Kokta, and D. Maldas. 1989. The xanthate method of grafting. XII.
Effect of operating conditions on the grafting of vinyl monomers onto wood pulp.
J. Appl. Polym. Sci. 38: 841-848.
De Ruvo, A., and E. Alfthan. 1978. Shifts in glass transition temperatures of synthetic
polymers filled with microcrystalline cellulose. Polymer 19(8): 872-874.
Dimov, K., and P. Pavlov. 1969. Grafting with acrylonitrile with the redox system
cellulose xanthogenate-hydrogen peroxide. J. Polym. Sci. 7: 2775-2792.
Gatenholm, P., J. Felix, C. Klason, and J. Kubát. 1993. Methods for improvement of
properties of cellulose-polymer composites. Pages 20-24 in M. P. Wolcott, ed.
Wood Fiber/Polymer Composites: Fundamental Concepts, Processes, and
Materials Options. Proc. of the 1st Wood Fiber-Plastic Composite Conference in
Madison, WI.
Gatenholm, P., P. Hendenberg, and C. Klason. 1995. Recycling of mixed plastics using
cellulosic reinforcement. Pages 367-377 in C.P. Rader, S. D. Baldwin, D.D.
Cornell, G. D. Salder and R. F. Stockel, eds. Plastics, Rubber, and Paper
34
Recycling: A Pragmatic Approach. ACS Symposium Series 609. American
Chemical Society, Washington, D. C. Chapter 30.
Hamed, P., and A.Y. Coran. 1978. Reinforcement of polymers through short cellulose
fibers. Pages 29-50 in R. B. Seymour, ed. Additives for Plastics, vol. I. State of
the art. Academic Press, New York, NY.
Han, G. –S., H. Ichinose, S. Takase, and N. Shiraish. 1989. Composites of wood and
polypropylene III. Mokuzai Gakkaishi 35(12): 1100-1104.
Hornof, V., B. V. Kokta, and J. L. Valade. 1976. The xanthate method of grafting. IV.
Grafting of acrylonitrile onto high-yield pulp. J. Appl. Polym. Sci. 20: 1543-1554.
Hua, L., P. Zadorecki, and P. Flodin. 1987. Cellulose fiber-polyester composites with
reduced water sensitivity. I. Chemical treatment and mechanical properties.
Polym. Comp. 8(3): 199-202.
Kishi, H., M. Yoshioka, A. Yamanoi, and N. Shiraishi. 1988. Composites of wood and
polypropylenes I. Mokuzai Gakkaishi 34(2): 133-139.
35
Klason, C., J. Kubát, and H. –E. Strömvall. 1984. The efficiency of cellulosic fillers in
common thermoplastics. Part I. Filling without processing aids or coupling
agents. Intern. J. Polymeric Mater. 10: 159-187.
Kokta, B. V., and J. L. Valade. 1972. Effect of acrylonitrile on grafting of styrene with
the redox system cellulose xanthate-hydrogen peroxide. TAPPI 55(3): 366-369.
Maldas, D., and B. V. Kokta. 1989. Improving adhesion of wood fiber with polystyrene
by the chemical treatment of fiber with a coupling agent and the influence on the
mechanical properties of composites. J. Adhes. Sci. Technol. 3(7): 529-539.
Maldas, D., and B. V. Kokta. 1990a. Effects of coating treatments on the mechanical
behavior of wood fiber-filled polystyrene composites. II. Use of inorganic
salt/polyvinyl chloride and isocyanate as coating components. J. Reinf. Plast.
Comp. 8: 2-12.
36
Maldas, D., and B. V. Kokta. 1990b. Effects of coating treatments on the mechanical
behavior of wood-fiber-filled polystyrene composites. I. Use of polyethylene and
isocyanate as coating components. J. Appl. Polym. Sci. 40: 917-928.
Maldas, D., and B. V. Kokta. 1990c. Influence of phthalic anhydride as a coupling agent
on the mechanical behavior of wood fiber-polystyrene composites. J. Appl.
Polym. Sci. 41: 185-194.
Maldas, D., and B. V. Kokta. 1990d. Influence of polar monomers on the performance of
wood fiber reinforced polystyrene composites. I. Evaluation of critical conditions.
Int. J. Polym. Mater. 14(3-4): 165-189.
Maldas, D., and B. V. Kokta. 1991a. Surface modification of wood fibers using maleic
anhydride and isocyanate as coating components and their performance in
polystyrene composites. J. Adhesion Sci. Technol. 5(9): 727-740.
Maldas, D., and B. V. Kokta. 1991b. Influence of maleic anhydride as a coupling agent
on the performance of wood fiber-polystyrene composites. Polym. Eng. Sci.
31(18): 1351-1357.
Maldas, D., and B. V. Kokta. 1991c. Influence of organic peroxide on the performance of
maleic anhydride coated cellulose fiber-filled thermoplastic composites. Polym. J.
23(10): 1163-1171.
Maldas, D., and B. V. Kokta. 1994. An investigation of the interfacial adhesion between
reclaimed newspaper and recycled polypropylene composites through the
investigation of their mechanical properties. J. Adhes. Sci. Technol. 8(12): 1439-
1451.
Maldas, D., B. V. Kokta, and C. Daneault. 1989a. Influence of coupling agents and
treatments on the mechanical properties of cellulose fiber-polystyrene
composites. J. Appl. Polym. Sci. 37: 751-775.
37
Meyer, J. A. 1968. Crosslinking affects sanding properties of wood-plastic. Forest Prod.
J. 18(5): 89.
Meyer, J. A. 1981. Wood-polymer materials: State of the art. Wood Sci. 14(2): 49-54.
Meyer, J. A. 1982. Industrial use of wood polymer materials: State of the art. Forest Prod.
J. 32(1): 24-29.
Meyer, J. A. 1984. Wood polymer materials. Pages 257-289 in R. M. Rowell, ed. The
Chemistry of Solid Wood. ACS Advances in Chemistry Series 207. American
Chemical Society, Washington, D.C.
Morrison, R. T., and R. N. Boyd. 1992. Organic Chemistry. Sixth Edition. Prentice-Hall,
Inc., Englewood Cliffs, New Jersey. 971-985 pp.
Myers, G. E., I. S. Chahyadi, C. Gonzalez, and C. A. Coberly. 1993. Wood flour and
polypropylene or high-density polyethylene composites: Influence of maleated
polypropylene concentration and extrusion temperature on properties. Pages 49-
56 in M. P. Wolcott, ed. Wood Fiber/Polymer Composites: Fundamental
Concepts, Processes, and Materials Options. Proc. of the 1st Wood Fiber-Plastic
Composite Conference in Madison, WI.
Oksman, K., and H. Lindberg, and A. Holmgren. 1998. The nature and location of SEBS-
MA compatibilizer in polyethylene-wood flour composites. J. Appl. Polym. Sci.
69: 201-209.
Radian Corporation. 1987. Chemical Additives for the Plastics Industry: Properties,
Applications and Toxicologies. Noyes Data Corporation, Park Ridge, NJ. pp. 55-
59.
Raj, R. G., and B.V. Kokta,. 1991. Improving the mechanical properties of HDPE-wood
fiber composites with additives/coupling agents. Pages 1883-1885 in ANTEC,
Proc. of the 49th Annual Technical Conference, Montreal, Canada, May 5-9,
1991. Society of Plastics Engineers, Brookfield, CT.
Raj, R. G., B.V. Kokta, D. Maldas, and C. Daneault. 1988. Use of wood fibers in
thermoplastic composites: VI. Isocyanate as a bonding agent for polyethylene-
wood fiber composites. Polym. Comp. 9(6): 404-411.
Raj, R. G., B.V. Kokta, D. Maldas, and C. Daneault. 1989. Use of wood fibers in
thermoplastics. VII. The effect of coupling agents in polyethylene-wood fiber
composites. J. Appl. Polym. Sci. 37: 1089-1103.
Raj, R. G., B.V. Kokta, G. Grouleau, and C. Daneault. 1990. The influence of coupling
agents on mechanical properties of composites containing cellulosic fillers.
Polym. Plast. Technol. Eng. 29(4): 339-353.
Rosen, M. J. 1978. Surfactants and Interfacial Phenomena. John Wiley & Sons, New
York, NY. p. 266.
Rowell, R. M., and P. Konkol. 1987. Treatments that enhance physical properties of
wood. U.S. Forest Products Laboratory General Technical Report FPL-GTR-55.
12 pp.
39
Rowell, R. M., R. Moisuk, and J. A. Meyer. 1982. Wood-polymer composites: cell wall
grafting with alkylene oxides and lumen treatments with methyl methacrylate.
Wood Sci. 15(2): 90-96.
Sain, M. M., B. V. Kokta, and D. Maldas. 1993. Effect of reactive additives on the
performance of cellulose fiber-filled polypropylene composites. J. Adhesion Sci.
Technol. 7(1): 49-61.
Schneider, M. H. 1994. Wood polymer composites. Wood Fiber Sci. 26(1): 142-151.
Selke, S. E., K. Nieman, J. Childress, M. Kel, and R. Bimpson. 1990. Use of eastern
hardwoods in wood fiber/plastic composites. Pages 35-42 in Advanced
Technology Applications to Eastern Hardwood Utilization. Michigan State
University, East Lansing, MI.
Simonsen, J., and T. Rials. 1992. Enhancing the interfacial bond strength of
lignocellulosic fiber dispersed in synthetic polymer matrices. Pages 105-111 in R.
M. Rowell, T. L. Laufenberg, and J. K. Rowell, eds. Materials Interactions
Relevant to Recycling of Wood-Based Materials. Vol. 266. Materials Research
Society, Pittsburgh, PA.
Simonsen, J., and T. Rials. 1996. Morphology and properties of wood-fiber reinforced
blends of recycles polystyrene and polyethylene. J. Thermoplastic Comp. Mater.
9: 292-302.
40
Simonsen, J., R. Jacobsen, and R. Rowell. 1998. Wood-fiber reinforcement of styrene-
maleic anhydride copolymers. J. Appl. Polym. Sci. 68: 1567-1573.
Štepek, J., and H. Daoust. 1983. Additives for Plastics. Polymer/Properties and
Applications 5. Springer-Verlag, New York. p. 84.
Takase, S., and N. Shiraishi. 1989. Studies on composites from wood and polypropylene.
II. J. Appl. Polym. Sci. 37: 645-659.
Zadorecki, P., and P. Flodin. 1985. Surface modification of cellulose fibers. II. The effect
of cellulose fiber treatment on the performance of cellulose-polyester composites.
J. Appl. Polym. Sci. 30:3971-3983.
41