Professional Documents
Culture Documents
... dry-tech bearings ... 2016 ... plastics for longer life
®
bearings
... linear systems and spherical bearings
Plastics for longer life®
Plastics in motion
Dear Customer,
For over 30 years igus® has been developing tribologically optimized
plastic materials for all applications. This continuous development
allows us to continually improve the world of motion plastics.
In this catalog you will find solutions for a vast range of technical
requirements, utilizing the technical advantages of 46 motion plastic
materials. Approximately 12,400 self-lubricating, maintenance-free, and
cost-effective bearing products are available from stock and ready to
ship in as little as 24 hours.
If you cannot find a solution for your requirements in this catalog, please
contact us.
Thomas M. Miller
Legal Information
The information in this catalog, and the data in the design section in particular, is based on our current knowledge of the
products described, and no legally binding assurance in respect to characteristics or suitability for an application can
be derived from it. igus® is unable to assume liability of any nature for damage, loss, or injury resulting from application
of igus® products. We recommend that you always check the suitability of igus® products for a specific intended
application in a practically-oriented test. For reasons relating to ongoing technical developments, we reserve the right to
implement technical modifications and improvements of the products in this catalog at any time. This catalog is subject
to printing errors.
The terms igus, e-ketten, e-kettensysteme, E-chain, E-Chain System, Energy Chain, Energy Chain System, ReadyChain,
ReadyCable, Chainflex, iglidur, iglide, igubal, drylin, xiros, xirodur, manus, vector, Robolink, pikchain, dry-tech, motion
plastics, CFRIP, speedigus, dryspin and plastics for longer life are legally protected trademarks for igus® Inc. and/or
igus® GmbH/Cologne in the Federal Republic of Germany and, where applicable, other countries.
iglide
1
®
2
bearings: 46 different iglide® materials from stock.
iglide ®
3
double flange bearings and a complete range of slewing rings bearings.
iglide ®
Bar stock
from page
iglide® materials for design freedom: Bar stock made from tribo-material, Tribo-Tape and
663
4
unique on the market: iglide® Tribo-Filament.
xiros ®
Ball bearings
from page
Self-lubricating groove ball bearings and other ball bearing types made from igus®
5
triboplastics, for maximum service life and reduced coefficient of friction. 693
igubal ®
6
and are more economical and lighter than conventional metallic spherical bearings.
DryLin ®
Linear technology
from page
Slides instead of rolling. Self-lubricating linear guide systems with rails and shafts.
881
7
Modular and cost-effective in different sizes for almost all linear adjustments.
DryLin ®
8
trapezoidal and metric threads. Self-lubricating and maintenance-free.
DryLin ®
9
with lead screws/toothed belt drives/rack drives for manual adjustment or with motor.
The most sold iglide® Low coefficients of Excellent vibration Low cost, low wear: Low wear on High temperatures,
bearing worldwide: friction and wear: dampening: iglide® R all shafts: chemical resistance:
iglide® G300 iglide® J iglide® M250 iglide® L280 (W300)* iglide® T500 (X)*
➤ Page 83 ➤ Page 115 ➤ Page 135 ➤ Page 159 ➤ Page 171 ➤ Page 193
4 iglide® materials 7 iglide® materials 4 iglide® materials 5 iglide® materials 9 iglide® materials 3 iglide® materials for
for general purpose for long service life for high temperatures with high chemical for contact with food high loads
resistance
➤ Page 212 ➤ Page 254 ➤ Page 320 ➤ Page 364 ➤ Page 418 ➤ Page 500
9 iglide® materials
for special application
areas
➤ Page 534
Security with the Easy installation due With anti-rotation Press in and fold Press and plug: Join and snap into
double flange to split design: feature down: Double flange bearing place:
design: Split bearings Flanged bearing Special solution
Clip bearings Snap-on
➤ Page 614 ➤ Page 616 ➤ Page 618 ➤ Page 620 ➤ Page 621 ➤ Page 622
High strength: With outer drive Light weight: Special geometries Universal sliding Motor-driven iglide®
Type 01 ring: Type 02 and accessories pads PRT slewing ring
Type 01 bearings
➤ Page 650 ➤ Page 651 ➤ Page 652 ➤ Page 653 ➤ Page 656 ➤ Page 657
For free design: For free design: In larger diameters iglide® off the reel: For conventional 3D
19 iglide® materials iglide® as plate material as a tube: Tribo-Tape printers:
as round bars iglide® J A160 / V400 Tribo-Filament
➤ Page 667 ➤ Page 675 ➤ Page 675 ➤ Page 683 ➤ Page 687
The ball bearings New size: FDA compliant: Protection against Space saving: FDA compliant:
standard: Size 62 xirodur® B180 dirt: Thin ring bearing xirodur® A500
xirodur® B180 with PE cage With shield with PEEK cage
➤ Page 704 ➤ Page 706 ➤ Page 706 ➤ Page 706 ➤ Page 706 ➤ Page 708
xiros® radial deep groove ball bearings ... for special application areas
ESD protection & FDA Detectable: For tobacco High speeds: High temperatures:
compliant: xirodur® xirodur® M180 industry: xirodur® D180 xirodur® G220
F180, PE cage xirodur® T220
➤ Page 712 ➤ Page 714 ➤ Page 715 ➤ Page 716 ➤ Page 717
Product overview
Flange bearing xiros® – More designs made of xirodur® B180
Ball bearings with System-solution: Higher loads: Spherical outer Good axial stability:
single/double Aluminum tube with xirodur® B180, diameter: End caps
flange flange ball bearing double row xirodur® B180 / M180
➤ Page 720 ➤ Page 722 ➤ Page 718 ➤ Page 723 ➤ Page 724
Multi axis Skate wheel Axial-thrust bearing Axial double row Thrust washer
bearing
➤ Page 719 ➤ Page 725 ➤ Page 726 ➤ Page 726 ➤ Page 727
xiros® – More designs made of xirodur® B180 xiros® and igubal® combined
Plastic transfer unit Axial polymer Slewing ring bearing Combination with Combination with
with clamp rings transfer unit pillow block bearings: flange bearings:
Fixed/Pivoting 4-holes / 2-holes
➤ Page 728 ➤ Page 728 ➤ Page 729 ➤ Page 730 ➤ Page 732
Rod ends with female/ For temperatures Angled and in-line Axial joint removable Easy assembly: Can be combined with
male thread up to +392 °F joints Clevis joint rod ends:
combinations Individual components
➤ Page 754 ➤ Page 766 ➤ Page 779 ➤ Page 781 ➤ Page 795 ➤ Page 800
For small space require Easy assembly/ Shafts guides and For higher radial Housing with ball Housing with ball
ment, cost-effective: disassembly: flange bearings, loads stud: stud:
Pillow block bearings, Split housing Inch and metric sizes Inch and metric sizes Female thread Male thread
7 versions
➤ Page 806 ➤ Page 813 ➤ Page 822 ➤ Page 826 ➤ Page 830 ➤ Page 831
uuu
igubal® – Flange bearings igubal® – Pressfit bearings
➤ Page 832 ➤ Page 833 ➤ Page 835 ➤ Page 847 ➤ Page 850
Weight reduction: 8 different materials: For metallic bearing Quick to find: Quick to find:
Spherical thrust Spherical balls housings igubal® detectable igubal® detectable
bearing Rod ends Clevis joints
➤ Page 853 ➤ Page 857 ➤ Page 871 ➤ Page 876 ➤ Page 878
Single rails and Weight saving: Fast assembly: Manual clearance Corrosion resistant: Double rails:
housing bearings: Housing bearing made Housing bearing adjustment: Stainless steel square
square/round from aluminum tandem “Turn-To-Fit” bearing versions, single/double ➤ Page 928
round
➤ Page 920 ➤ Page 921 ➤ Page 924 ➤ Page 925 ➤ Page 926 ➤ Page 932
High strength: Complete carriages: Simple assembly Reduced weight: Wear resistant: For simple
High profile rail square without alignment: Double rail Slider-rail positioning:
➤ Page 930 Mono-slide carriage Manual clamp WHKA
round
➤ Page 933 ➤ Page 934 ➤ Page 931 ➤ Page 935 ➤ Page 936 ➤ Page 937
For higher retention Roll and slide: Higher load capacity: For lateral Compact: Smooth and quiet
forces: Hybrid bearings Hybrid double roller adjustments: Hybrid carriages operation:
Manual clamp WHKD bearing Hybrid carriages Hybrid carriages
➤ Page 938 ➤ Page 946 ➤ Page 947 ➤ Page 948 ➤ Page 948 ➤ Page 949
Product overview
DryLin® N low- profile guide systems
Smallest installation The largest variety of Suitable for aluminum High loads with Telescopic system: Telescopic rails with
space and high load carriages (options): construction profiles: reduced space: DryLin® NT locking mechanism
capacity: Size 27 Size 40 Size 80
Size 17
➤ Page 958 ➤ Page 960 ➤ Page 962 ➤ Page 964 ➤ Page 966 ➤ Page 967
➤ Page 968 ➤ Page 979 ➤ Page 980 ➤ Page 981 ➤ Page 982 ➤ Page 983
Miniature guide: Adjustable miniature Accessories for fast Self-lubricating: Aluminum or Housing bearing
DryLin® TK-04 guide: positioning: Liners and pressfit stainless steel linear and floating housing
DryLin® TKE-04 Clamps bearings bearings with liners bearings
➤ Page 984 ➤ Page 985 ➤ Page 986 ➤ Page 1004 ➤ Page 1016 ➤ Page 1018
For quick For supported shafts: Pillow block housing Twin Pillow block Easy
replacement Open linear plain closed and open housing closed and installation:
bearings styles open styles Flange bearing
➤ Page 1025 ➤ Page 1030 ➤ Page 1036 ➤ Page 1038 ➤ Page 1040
Self-lubricating: Self-lubricating Aluminum or Housing bearing For quick For supported shafts:
Liners and pressfit adjustment: stainless steel linear and floating housing replacement Open linear plain
bearings DryLin® slide discs bearings with liners bearings bearings
➤ Page 1042 ➤ Page 1055 ➤ Page 1058 ➤ Page 1060 ➤ Page 1069 ➤ Page 1071
uuu
DryLin® R shaft guides - Metric
Square For all unsupported Adjustable bearing Q20 pillow block Flange bearings: Q10 pillow block:
section rail solutions: housing with manual square or round Solid plastic
small and adjustable clamp
➤ Page 1122 ➤ Page 1123 ➤ Page 1124 ➤ Page 1125 ➤ Page 1126 ➤ Page 1127
Components kit:
Extensive accessories
➤ Page 1128
Better efficiency: Zero backlash: High helix lead screws High helix lead Zero backlash lead
dryspin® Technology dryspin® lead screw screw nuts screw nuts
nuts Cylindrical and with flange
➤ Page 1166 ➤ Page 1168 ➤ Page 1170 ➤ Page 1171 ➤ Page 1173
ACME Lead screws ACME lead screw Trapezoidal lead LH/RH lead screws Trapezoidal lead Wear resistant and
nuts, sleeve or flange, screws in different screw nuts made from robust: lead screw nuts
available in five
materials versions iglide® materials made from iglide® R
➤ Page 1180 ➤ Page 1184 ➤ Page 1186 ➤ Page 1188 ➤ Page 1190 ➤ Page 1190
Lead screw nuts Miniature lead Anti backlash lead Two-start Clearance free Lead screw nut for
with spanner flat screw nuts screw nuts trapezoidal lead assembly: HTS linear modules
screw nuts DryLin® Disc
made from iglide® J
➤ Page 1192 ➤ Page 1193 ➤ Page 1194 ➤ Page 1196 ➤ Page 1212 ➤ Page 1214
Split lead screw Combination: Spherical high helix Spherical lead screw Fast-Forward: Lead screw support
nuts Lead screw nut with lead screw nut with nut with spherical Quick-release nut blocks
housing block spherical ball ball in pillow block
bearing housing
➤ Page 1216 ➤ Page 1217 ➤ Page 1218 ➤ Page 1219 ➤ Page 1220 ➤ Page 1222
Linear modules: Cross slides standard/ Linear module based With protected lead Controlled separately: Cross slide
DryLin® HTS preload versions: on DryLin® W: screw: DryLin® SLWT solutions:
DryLin® HTS-XY DryLin® SLW DryLin® SLW-PT DryLin® SLW-XY
➤ Page 1248 ➤ Page 1258 ➤ Page 1266 ➤ Page 1268 ➤ Page 1269 ➤ Page 1272
Solid plastic linear Miniature linear modules Low profile height easytube linear Adjust and direct Lead screw clamp
modules : for small place require light and flat: modules: readout: and hand wheel
DryLin® HTSP ment: DryLin® SLN DryLin® SLN preload DryLin® SET Position indicator
➤ Page 1277 ➤ Page 1281 ➤ Page 1284 ➤ Page 1287 ➤ Page 1296 ➤ Page 1297
360° continuously For manual orientation For 3-axis-systems: Individual positioning Toothed belt axis, Cost-effective, for
variable adjustment: of accessories: Angle kit of hand wheels: 4 sizes, 4 versions: format adjustments:
V-drives Adapter plate Flexshaft DryLin® ZLW DryLin® ZLW Eco
➤ Page 1298 ➤ Page 1300 ➤ Page 1301 ➤ Page 1302 ➤ Page 1310 ➤ Page 1310
10
igus® headquarters in Cologne – research, development and production from a single location.
C C
dry-tech
®
plastic
polymer life up bearings
cost
down 24 hrs
from 24h
C C
dry-tech:
Improve technology and reduce costs
More than 50% of machine failures are caused by deficient lubrication. igus® dry-tech bearings are
an alternative for lubricated plain and roller bearings. igus® develops tribopolymers for continuous
dry-running operation.
By avoiding lubrication, dry-tech polymer technology attains superior service life: from –148°F
up to +482°F at continuous exposure, from cleanrooms to extreme dirt exposure, from vacuum
to extreme humidity.
dry-tech: More than USD 700 M caused by excessive friction and wear due to inadequate lubrication.
igus® dry-tech bearings reduce your costs. A direct product comparison shows that you can
reduce your current costs for bearing components by as much as 50%.
➤ www.igus.com/dry-tech
11
Cost down,
life up!
Innovations with high-performance plastics
igus® plastic plain bearings constitute the step from a
simple plastic bushing to a tested, predictable and available
machined component.
Our research is based on specific bearing properties –
especially life cycle – achieved by continuous advancements
in materials.
12
Resistant to dirt with igus®. Zero-maintenance and high
dirt resistance are not the only advantages of DryLin®.
Longer life cycles – lower costs!
plain bearings
from page 47
Excellent plastics, improved through precise additions of
reinforcements and solid lubricants, tested thousands of
times, and proven millions of times – that is iglide®.
Every year, igus® engineers develop more than 100 new
plastic compounds and conduct more than 5,000 tests on
maintenance-free plain bearings. Over the years, this has
made it possible to establish a large database of plastics’
tribological properties.
In addition to their general properties, every iglide® bearing
material possesses a number of special features making it
suitable for particular applications and requirements.
Online tools:
14
Practical example
15
Other designs,
such as iglide ®
PRT –
from page 605
iglide® PRT is a slewing ring bearing with the proven and
tested advantages of the igus® plastic bearings. The sliding
elements made from iglide® materials operate absolutely
maintenance-free and self-lubricating. All housing parts
are made from aluminum and the running surfaces of the
iglide® materials sliding elements are hard-anodized. All fixing
screws are made from stainless steel.
Online tools:
16
Practical example
17
xiros plastic ®
ball bearings
from page 693
The xiros® plastic ball bearings are single-row grooved
ball bearings based on DIN 625. The self-lubricating and
maintenance-free ball bearings consist of four components:
The outer race
The inner race
The cage
And the balls
The inner and outer races are made from igus® triboplastics
to maximize service life and minimize coefficients of friction. In
contrast to metallic ball bearings, xiros® plastic ball bearings
manage without external lubrication. For this reason they are
suited for a multitude of applications that depend not on
extreme rotary speeds or loads, but just on lubrication free
application in contrast to permanently lubricated metallic ball
bearings. These areas include food and medical industries,
packaging and textile industries, or the chemical industry
and cleanroom applications as well as electronics and office
technology.
Online tools:
18
Practical example
19
igubal spherical ®
bearings
from page 737
igubal® spherical bearings are self-aligning components
made entirely of high-performance plastics.
The igubal® series provides designers with a complete sys-
tem of self aligning bearings: Rod ends, clevis joints, flange
bearings, pivot bearings and pillow blocks.
Self-adjusting bearings are easy to fit, adaptable to wide
angular ranges and have been used to replace special
housings in many cases.
igubal® offers all the advantages of high-performance
plastics, including dry-running capability combined with
very good vibration dampening.
igubal® spherical bearings are insensitive to dirt, liquids,
chemicals and fully corrosion-proof.
Bearings from the igubal® range are very light, compact and
economical on two fronts:
●L ow purchase price
● Low maintenance and installation costs
Online tools:
Lifetime
calculation
online
20
Practical example
21
DryLin linear and ®
drive technology
from page 881
DryLin® linear plain bearings are an ideal alternative to
traditional re-circulating ball bearing systems. These sliding
plain bearings are made of high-performance polymers
from igus®’ iglide® series. DryLin® linear bearings can be
used if dirt, dust or moisture is present, for short stroke
applications, or if a lubrication-free solution is needed.
DryLin® linear slide tables are also designed for dry running.
As a result, dust and dirt will not cling to the bearing
surfaces. DryLin® linear bearings also have no minimum
stroke-length restrictions, unlike re-circulating ball bearings.
They deliver quiet operation and are corrosion-resistant.
igus® also offers flat, compact lead screw linear tables for
variable formats and handling tasks. The linear table is
extremely rigid due to the hard-anodized aluminum shaft
and is also made of igus®’ high-performance iglide® plastics.
Online tools:
DryLin® W
product configurator
23
Self-lubricating
bearings
from igus ®
24
A study has found that no less than half of all machine
lubricants currently used in Germany seeps into soil and
waters or evaporates into the atmosphere. According
to a research team of chemists, mechanical engineers
and environmentalists from the RWTH in Aachen, the
estimates for Germany alone consume 250,000 tons per
year. This corresponds to the amount required to fill
8,000 tankers.
16
14
12
10
8
6
4
2
0
Aluminum Steel Plastics
25
Reduce process
costs: bearings
online
For the products in this catalog, further information and
materials are available on our website, including:
Online product and service life calculators
2D or 3D-CAD files
PDF-data and other formats for download
Application photos
Imperial/metric dimensions
Personal support
Online pricing and shopping cart
26
SEARCH
iglide® product finder
Find the right bearing quickly.
ORDER
iglide® online catalogue
The online catalogue is just a click away.
See all important product details, information and tools
by clicking again on the corresponding link.
CALCULATE
iglide® life time calculation
Simple and quick input of your application parameters,
allows a precise calculation of the life cycle. Also
download and save CAD data free of charge.
27
Quick and reliable.
igus delivery
®
service.
The igus® delivery service:
Shipped from stock as early as same day
Order at igus®:
No minimum order quantities, no surcharges.
28
24 hrs 24-48 hrs 24-72 hrs 3-10 days 3-6 weeks
29
Quality from the
igus laboratory ®
8.0 9
7.0 8
6.0 7
6
5.0
5
4.0
Wear [µm/km]
Wear [µm/km]
4
3.0 3
2.0 2
1.0 1
0.0 0
0 1 2 3 4 5 0 1 2 3 4 5
0.5 4.0
3.5
0.4
3.0
Automatic screw steel
0.3 2.5
Cf53, hard chromed
2.0
High grade steel
HR carbon steel
H. a. aluminium
Wear [µm/km]
0.2 1.5
Pressure [µ]
1.0
304 SS
0.1
Cf53
0.5
0.0 0.0
0 10 20 30 40 50 60 70 80
Shaft materials
RoHS
ISO 9001:2008 TS16949
Friction and abrasion measurement in a rotation Bench test for loads up to 21,755 psi and
test temperatures up to 482 °F.
31
The flexible
igus factory ®
igus® US Headquarters
Rumford, RI
32
Investments in better technology and faster delivery times
33
1965 1971 1980 1991 1995
First iglidur® First First xigus 1.0 readychain
The igus story: ® slide ele- E-Chain® Polymer electronic with the slo
ment: plug (series 20) Bearings catalogue gan "Chain-
valve for the catalogue, Cable ®
,
company 8 pages Guarantee" -
1964 to present.
Pierburg
160
10 3 27
8.000
34 1.000
2001 2003 2005 2007 2008 2009 2010 2011 2012 2013 2014
System E6 triflex® R iglidur® PRT System E4.1 E4.350 – RX e-tube – twisterband: E4.1 light – Alternative Guide ISO Class-1
e-chains® 3D e-chains® slewing ring e-chain® largest chip-proof turn 7000 ° Allrounder to cable upward: certified
bearing polymer e-chain® drums: liftband cleanroom
e-chain® for high e-spool e-chain®
dynamics modular kit
2001 2003 2006 2007 2008 2009 2010 2011 2012 2013 2014
drylin® N drylin® W System P4 drylin® ZLW xiros® guidelok pikchain®, GLSL-F – flip open stripback iglidur®
minature modular rol e-chain® tooth belt polymer ball horizontal – for Pick & safe vertical chain links on cable with A160 tribo
linear guide linear guide axes bearings for long Place guide of triflex® TRLF CFRIP® tear adhesive
systems systems travels e-chains® strip liner
2000 05 06 07 08 09 10 11 12 13 14
90,000
80,000 2,200
45,000 1,800
33
1,600
1,000 26
subsidiaries
35
Individual
consultation
by igus® – via Providence
phone or at
your location
A large network of sales engineers is at
your disposal in Germany and worldwide.
We gladly provide consultation on your
premises, supply assembly instructions
3 29
and aids to installation sites, as well as
measure installation spaces and register
2
ambient conditions on location.
47
This has the following benefits for you:
We are wherever you need us
Numerous E-chain® and plastic
39
bearing consultants remain at your
disposal at all times
4
Rapid shipping is guaranteed
worldwide 14
Products are shipped from stock in 70
the shortest possible time 13
18
44
8
11 68
69
43 58 21
20
34
29 66 17 46 36 5 49
41
6 1 16 53
54 25 67
49
57 22 59 40 15 51 48
47 7 37 9 9 56 32
31 23 64 28
63 35 60
39 19 30 33 12
50 24 61
65
26 62 71
38 45
52
27
55 10 42
igubal® rod end bearings made from plastic display their strength in Maintenance free iglide® bearings in a calibration cage of a blown
the demanding environment. film line.
Reduction of the drive power for bottle washing machines with Self-lubricating DryLin® guides in filling systems. Resistant to
iglide® RN plain bearings. chemicals and frequent cleaning.
DryLin® R linear bearings in a transfer unit: igubal® spherical bearings are used in the main bearing assembly
100 % self-lubricating and resistance to pungent detergents. of every individual slat owing to their freedom from maintenance,
corrosion resistance and atmospheric resistance.
39
Always at your service ...
... and so cost-efficient; plastic bearings
guard against downtimes in the long term.
Practical examples:
Resistant to dirt
DryLin® linear guiding system in the EURO-C welding tongue for the DryLin® trapezoidal lead screw nuts and screws in a wood
automotive industry. packaging system.
Harsh surroundings: Lubrication free igubal® rod end bearings in DryLin® R in pulp cutting machine.
the interlocking machine.
Lead screw unit HTSP-12 with lead screw clamping, Plastic plain bearings in the various hinges, locks and hydraulic
position indicator and hand wheel ensures quick cylinders of the root ball transplanter.
and repeatable format adjustments.
41
Special solution increases service life …
The new two-component bearing guarantees
smooth and wear-free movements on the
expensive PEEK rotating axis.
Practical examples:
Packaging industry
This application uses DryLin® T linear guide system to steer iglide® Z bearings resist to temperatures of +320 °F and above and
gripping plates. meet the requirements of the crimpers in hose packaging machines
and are moreover absolutely wear resistant.
iglide® J plain bearings make the filling of PET bottles economic, are Operating temperatures up to max. +284 °F and detergent resistance
vibration dampening and among other things, impress by their good are not a challenge for plain bearings made from iglide® T500 (X).
chemical resistance.
Self-lubricating igubal® rod end bearings under extreme rough iglide® plain bearings and DryLin® liners ensure wear-free
conditions: they have been in trouble-free operation for over years in a production techniques under high mechanical stress.
packaging unit for profiles.
43
Light, corrosion free and economical bearings
are requirements in this application. In addition
iglide® G300 bearings offer low coefficients of
friction and are absolutely maintenance free.
Practical examples:
for almost every industry
DryLin® plastic plain bearings in an inspection device for offshore Self-lubricating iglide® plain bearings defy all adverse conditions in
drilling riser. the pendulum steering axles.
Flexible without fault: adjustable camera tripod with DryLin® W Trouble-free operation over years under the toughest conditions:
bearings for quiet operation. DryLin® R linear bearings replaced ball bushings.
Both the cross tube for the seat suspension and the attachment Lightweight and cost-effective iglidur® PRT slewing ring bearing in use
of the parachute rescue system are fixed on the hull with igubal® in a rotating spotlight.
flange bearings.
45
1. iglide ... ®
...
...
...plastics
Application Examples - iglide®
Best sellers
The best selling iglide® Low friction, low wear Excellent vibration Low cost
bearing worldwide dampening
iglide® G300 iglide® J iglide® M250 iglide® R
➤ Page 83 ➤ Page 115 ➤ Page 135 ➤ Page 159
iglide for all kind of applications – Standards and specialists from stock
®
General
purpose The most sold iglide® bearing
Excellent vibration dampening Low water absorption
Flexible, wear resistant &
worldwide more
iglide® G300 iglide® M250 iglide® P iglide® P210
➤ Page 83 ➤ Page 135 ➤ Page 217 ➤ Page 231
For long
service life Low friction,
Low wear on all shafts Ideal for plastic shafts
Runs up to three times
low wear longer than iglide® J
iglide® J iglide® L280 (W300)* iglide® J260 iglide® J3
➤ Page 115 ➤ Page 171 ➤ Page 259 ➤ Page 267
High
temperatures
High temperatures, chemical Runs up to six times For soft shafts, For high dynamic loads, wear
up to +482 °F resistance longer than iglide® T500 (X)* up to +392 °F resistant
iglide® T500 (X)* iglide® X6 iglide® V400 iglide® Z
➤ Page 193 ➤ Page 325 ➤ Page 335 ➤ Page 343
High media
resistance High temperatures, chemical
Universal
Long life For under
resistance operation water
iglide® T500 (X)* iglide® H iglide® H1 iglide® H370
➤ Page 193 ➤ Page 369 ➤ Page 377 ➤ Page 389
For contact
with food FDA-compliant general The food grade material, FDA-compliant, Temperature and wear
purpose material FDA-compliant/EC Directive for low speeds resistant, FDA-compliant
iglide® A180 iglide® A181 iglide® A200 iglide® A350
➤ Page 423 ➤ Page 431 ➤ Page 441 ➤ Page 447
For high
loads For high loads For extreme loads
iglide Q
®
iglide® Q2
➤ Page 505 ➤ Page 517
Special
application
areas Electrically conductive ESD compatible The automotive standard For fast rotation under water
iglide F
®
iglide F2
®
iglide H4
®
iglide® UW
➤ Page 539 ➤ Page 549 ➤ Page 557 ➤ Page 565
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
iglide® UW500
➤ Page 357
Up to +482 °F,
Low-cost
wear resistant
iglide C500
®
iglide® H2
➤ Page 403 ➤ Page 411
Temperature and chemical Chemicals & food, Robust KTW-compliant For the tobacco industry,
resistance, FDA-compliant FDA-compliant FDA-compliant
iglide® A500 iglide® A160 iglide® A290 iglide® UW160 iglide® T220
➤ Page 459 ➤ Page 471 ➤ Page 479 ➤ Page 485 ➤ Page 493
iglide® TX1
➤ Page 527
Standard Bar speedigus® Long life in High loads Dirt Low Chemical
Page
catalog range stock material dry operation resistant coefficient resistant
of friction
iglide® G300 83
iglide® J 115
Best sellers
iglide® Z 343
iglide UW500
®
357
iglide® H 369
High media
resistance
iglide H1
®
377
iglide® H370 389
iglide C500
®
403
iglide® H2 411
iglide A180
®
423
iglide® A181 431
For contact with food
iglide® Q2 517
iglide TX1
®
527
iglide® F 539
Special application
iglide® F2 549
iglide H4
®
557
areas
iglide® UW 565
iglide N54
®
573
iglide® G V0 581
iglide J2
®
589
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
iglide® G300 83
iglide® J 115
Best sellers
iglide® M250 135
iglide® R 159
iglide L280 (W300)*
®
171
iglide® T500 (X)* 193
iglide P
®
217
purpose
General
iglide® P210 231
iglide® K 241
iglide GLW
®
247
iglide® J260 259
iglide J3
®
267
temperatures
iglide V400
®
335
High
iglide® Z 343
iglide UW500
®
357
iglide® H 369
High media
resistance
iglide H1
®
377
iglide® H370 389
iglide C500
®
403
iglide® H2 411
iglide® A180 423
iglide A181
®
431
iglide® Q2 517
iglide® TX1 527
iglide F
®
539
Special application
iglide® F2 549
iglide H4
®
557
areas
iglide® UW 565
iglide N54
®
573
iglide® G V0 581
iglide J2
®
589
iglide J350
®
279
iglide® W360 291
iglide L250
®
299
iglide® D 307
iglide® J200 313
iglide X6
®
325
temperatures
iglide® Z 343
iglide UW500
®
357
iglide® H 369
High media
resistance
iglide H1
®
377
iglide® H370 389
iglide® C500 403
iglide H2
®
411
iglide® A180 423
iglide® A181 431
iglide A200 441
Applications with
®
food contact
iglide Q2
®
517
iglide® F 539
Special application
iglide F2
®
549
iglide® H4 557
areas
iglide® UW 565
iglide N54
®
573
iglide® G V0 581
iglide® J2 589
Maximum permissible surface pressure of iglide® bearings at Important temperature limits of iglide® bearings
+68 °F Maximum permissible application temperature, continuous
+176 °F Temperature where bearings need to be secured against
radial or axial movement in the housing
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Best sellers
iglide® M250 3 5 135
iglide® R 6 1 159
iglide L280 (W300)*
®
7 7 171
iglide® T500 (X)* 3 4 193
iglide P
®
3 1 217
purpose
General
iglide® P210 6 7 231
iglide® K 3 3 241
iglide GLW
®
1 2 247
iglide® J260 6 3 259
iglide® J3 7 3 267
temperatures
iglide® V400 7 3 335
High
iglide® Z 1 3 343
iglide UW500
®
3 6 357
iglide® H 3 5 369
High media
resistance
iglide H1
®
7 3 377
iglide® H370 2 2 389
iglide® C500 2 3 403
iglide H2
®
6 7 411
iglide® A180 5 3 423
iglide® A181 1 7 431
iglide A200 4 3 441
Applications with
®
food contact
iglide® A350 6 2 447
iglide A500
®
3 2 459
iglide® A160 6 7 471
iglide® A290 3 7 479
iglide UW160
®
3 2 485
iglide® T220 3 3 493
iglide® Q 6 3 505
loads
High
iglide Q2
®
4 4 517
iglide® F 6 1 539
Special application
iglide F2
®
3 3 549
iglide® H4 3 5 557
areas
iglide® UW 3 6 565
iglide N54
®
1 3 573
iglide® G V0 6 6 581
iglide® J2 7 3 589
Coefficients of friction of iglide bearings against steel rotating,
®
Wear of iglide bearings against steel rotating, p = 145 psi
®
p = 145 psi, v = 59 fpm Average of all the seven sliding combination tested
Average of all the seven sliding combinations tested Wear of best combination
Coefficient of friction of best combination
Shaft material:
1 = 1050, case hardened 3 = Hard anodized aluminum 5 = Machinery steel 7 = 440B stainless
2 = 1050, case hardened steel, chromed 4 = Free-cutting steel 6 = 304 stainless
L280 T500
G J M250 R P P210 K GLW
(W300)* (X)*
Density [g/cm3] 1.46 1.49 1.14 1.39 1.24 1.44 1.58 1.40 1.52 1.36
Color1)
General properties
Max. moisture
4.0 1.3 7.6 1.1 6.5 0.5 0.4 0.5 0.6 5.5
absorption [% weight]
Coefficient of sliding friction, 0.08– 0.06– 0.18– 0.09– 0.08– 0.09– 0.06– 0.07– 0.06– 0.10–
dynamic against steel [µ] 0.15 0.18 0.40 0.25 0.23 0.27 0.21 0.19 0.21 0.24
pv value, max. (dry) [psi x fpm] 12,000 9,700 3,400 8,700 6,600 37,700 11,000 11,500 8,600 8,600
Modulus of elasticity [psi] 1,131,000 348,100 391,600 282,800 507,600 1,174,800 768,700 362,600 507,600 1,116,500
Mechanical properties
Tensile strength at
30,460 10,590 16,240 10,150 18,130 24,660 17,400 10,150 11,600 34,075
+68 °F [psi]
Compressive strength [psi] 11,310 8,702 7,542 9,863 8,847 14,500 9,572 7,252 8,702 10,730
Shore-D-hardness 81 74 79 77 77 85 75 75 72 78
Physical and thermal properties
Min. application
–40 –58 –40 –58 –40 –148 –40 –40 –40 –40
temperature [°F]
Thermal conductivity
0.24 0.25 0.24 0.25 0.24 0.60 0.25 0.25 0.25 0.24
[W/m · K]
Specific volume
properties
Electrical
> 1013 > 1013 > 1013 > 1012 > 1013 < 105 > 1013 > 1012 > 1012 > 1011
resistance [Ωcm]
Surface
> 1011 > 1012 > 1011 > 1012 > 1012 < 103 > 1012 > 1011 > 1012 > 1011
resistance [Ω]
If you are unsure which material you need, please go back to relevant selection tables or call us.
According to main properties ➤ Page 52; According to performance ➤ Page 54
1)
Similar color, please refer to the individual materials tables in each chapter ➤ From page 83
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
UW
J260 J3 J350 W360 L250 D J200 X6 V400 Z H H1 H370 C500 H2
500
1.35 1.42 1.44 1.34 1.5 1.4 1.72 1.53 1.51 1.4 1.49 1.71 1.53 1.66 1.37 1.72
0.2 0.3 0.3 0.2 0.7 0.3 0.2 0.1 0.1 0.3 0.1 0.1 0.1 0.1 0.3 0.1
0.4 1.3 1.6 1.6 3.9 1.1 0.7 0.5 0.2 1.1 0.5 0.3 0.3 0.1 0.5 0.2
0.06– 0.06– 0.10– 0.07– 0.08– 0.08– 0.11– 0.09– 0.15– 0.06– 0.20– 0.07– 0.06– 0.07– 0.07– 0.07–
0.20 0.20 0.20 0.21 0.19 0.26 0.17 0.25 0.20 0.14 0.36 0.20 0.20 0.17 0.19 0.30
10,000 14,000 13,000 10,000 11,500 8,700 8,600 38,350 14,000 24,000 10,000 39,000 22,800 21,000 19,500 16,500
319,100 391,600 290,100 555,350 282,800 290,100 406,100 2,320,600 652,670 348,100 3,320,600 1,813,000 406,100 1,610,000 435,110 1,494,000
8,702 10,150 7,977 17,259 9,718 10,440 8,412 42,060 13,779 13,775 37,710 35,380 7,977 19,580 14,500 30,460
7,252 8,702 8,702 ND 6,817 10,150 6,237 27,557 6,819 9,425 20,305 11,750 11,310 11,460 15,950 15,810
5,802 6,527 8,702 10,878 6,527 3,336 3,336 21,755 6,527 21,750 20,305 13,050 11,600 10,880 15,950 15,950
77 73 80 80 68 78 70 89 74 81 86 87 77 82 81 88
+248 +194 +356 +356 +194 +194 +194 +482 +392 +482 +482 +392 +392 +392 +482 +392
+284 +248 +428 +392 +356 +230 +248 +599 +464 +590 +572 +464 +464 +464 +572 +464
–148 –58 –148 –40 –40 –58 –58 –148 –58 –148 –148 –40 –40 –40 –148 –40
0.24 0.25 0.24 0.24 0.24 0.25 0.24 0.55 0.24 0.62 0.6 0.6 0.24 0.5 0.24 0.24
13 13 7 6 10 11 8 1.1 3 4 4 4 6 5 9 4
> 1012 > 1012 > 1013 > 1013 > 1010 > 1014 > 108 < 105 > 1012 > 1011 < 109 < 105 > 1012 < 105 > 1014 > 1015
> 1010 > 1012 > 1010 > 1012 > 1011 > 1014 > 108 < 103 > 1012 > 1011 < 109 < 102 > 1011 < 105 > 1013 > 1014
Density [g/cm3] 1.46 1.38 1.14 1.42 1.28 1.00 1.41 1.04 1.28
Color1)
General properties
Max. moisture
1.3 1.3 7.6 1.9 0.5 0.1 7.3 0.1 0.5
absorption [% weight]
Coefficient of sliding friction, 0.05– 0.10– 0.10– 0.10– 0.26– 0.09– 0.13– 0.17– 0.20–
dynamic against steel [µ] 0.23 0.21 0.40 0.20 0.41 0.19 0.40 0.31 0.32
pv value, max. (dry) [psi x fpm] 8,750 8,750 2,900 11,500 8,000 7,800 6,600 6,250 8,000
Modulus of elasticity [psi] 333,600 277,500 362,600 290,100 522,100 166,900 1,276,000 195,700 261,100
Mechanical properties
Tensile strength at
12,760 6,962 16,820 15,950 20,310 2,756 36,260 3,191 9,427
+68 °F [psi]
Compressive strength [psi] 11,310 8,702 7,832 11,310 17,110 5,366 13,200 4,461 7,977
Shore-D-hardness 76 76 81 76 83 60 88 60 76
Physical and thermal properties
Min. application
–58 –58 –40 –148 –148 –58 –40 –58 –40
temperature [°F]
Thermal conductivity
0.25 0.25 0.24 0.24 0.24 0.30 0.24 0.50 0.24
[W/m · K]
Specific volume
properties
Electrical
> 1012 > 1012 > 1013 > 1011 > 1014 > 1012 > 1011 > 1012 > 1010
resistance [Ωcm]
Surface
> 1011 > 1012 > 1012 > 1011 > 1013 > 1012 > 1011 > 1012 > 1010
resistance [Ω]
If you are unsure which material you need, please go back to relevant selection tables or call us.
According to main properties ➤ Page 52; According to performance ➤ Page 54
1)
Similar color, please refer to the individual materials tables in each chapter ➤ From page 83
1.4 1.46 2.1 1.25 1.52 1.79 1.52 1.13 1.53 1.44 1.27
0.9 1.1 n.b. 1.8 0.2 0.1 0.2 1.6 0.7 0.2 3.0
4.9 4.6 0.1 8.4 0.4 0.2 0.8 3.6 4.0 1.3 9.3
0.05– 0.22– 0.09– 0.10– 0.16– 0.08– 0.15– 0.15– 0.07– 0.11– 0.14-
0.15 0.42 0.37 0.39 0.22 0.25 0.35 0.23 0.20 0.27 0.26
16,000 19,500 26,000 9,700 8,750 19,500 2,800 14,000 14,000 6,600 19,500
652,700 1,214,000 1,740,000 1,682,000 1,076,000 1,088,000 1,392,000 261,000 1,146,000 522,900 445,800
17,400 34,810 7,977 37,710 13,490 17,400 13,050 10,150 20,310 14,650 14,070
12,910 18,850 31,910 14,210 8,847 7,252 10,150 4,351 14,500 11,170 9,863
14,500 17,400 29,000 15,230 6,817 9,427 5,802 8,700 10,880 6,672 7,977
83 80 94 84 72 80 78 74 80 ND 80
+275 +266 +248 +284 +248 +392 +194 +176 +266 +194 +284
+311 +392 +338 +356 +329 +464 +230 +248 +410 +230 +356
–40 –40 –76 –40 –40 –40 –58 –40 –40 –58 -40
0.23 0.24 0.24 0.65 0.61 0.24 0.6 0.24 0.25 0.25 0.24
5 8 3 12 5 5 6 9 9 7 7
> 1015 > 1013 > 1011 < 103 < 109 > 1013 < 105 > 1013 > 1012 > 1013 > 1010
> 1012 > 1011 > 1013 < 102 < 109 > 1012 < 105 > 1011 > 1011 > 1012 > 1012
➤ www.igus.com/online-tools
igus® plastic bearings, over 40 years of knowledge and progressive innovation for longer life solutions in all industries
Over and above the general properties, each iglide® bearing material
possesses a series of special properties and strengths, which
make it specially suitable for certain applications and requirements. Picture 04: Injection molded iglide® plain bearings are homogeneously
You can find a comprehensive description of the materials in the structured. Base polymer, bonding materials and solid lubricants
respective chapters before the dimensions tables. mutually complement each other.
The iglide® solution: the self-lubricating effect Base polymers and technical fibers
The high performance iglide plain bearing materials are composed
®
The radial pressure, with which the bearings are loaded, is
of: received by the plastic base material. In the contact area, this
material provides shaft support. The polymer base material
Base polymer Solid lubricants
ensures the lubricants do not receive a surface pressure that is
Fibers and/or filaments
too high. The base material is also reinforced by technical fibers
These components are not applied in layers, but instead are or filaments. These additional materials stabilize the bearing,
homogeneously blended. The advantage of this design is clear especially in cases of continuous stress.
when the requirements on the bearings surface are studied:
Picture 06: Base polymers with fibers and solid lubricants, magnified
200 times, dyed.
Diagram 01: During the start-up phase, the wear rate drops
significantly, and then stabilizes.
➤ www.igus.com/iglide-expert
[p] in psi. For this purpose, the radial load is determined on the 11,600
F
Thrust bearing: p =
0
π 68 122 176 248 302
(d2 2
– d12 ) ·
4
Temperature [°F]
In these equations:
iglide G300
®
iglide® J3 iglide® A290
F load in lbs iglide® J iglide® L250 iglide® T220
iglide® M250 iglide® R iglide® F
d1 bearing inner diameter in inches iglide® L280 (W300)* iglide® D iglide® Q
iglide® P iglide® J200 iglide® UW
b1 bearing length in inches iglide® GLW iglide® A180 iglide® B
iglide® J260 iglide® A200 iglide® C
d2 outer diameter of the bearing in inches
load is short. For a few minutes, the load can be more than Temperature [°F]
iglide® T500 (X)* iglide® Z iglide® H2
doubled, depending on the material. Please contact igus® for iglide® K iglide® UW500 iglide® A350
iglide® J350 iglide® H iglide® A500
additional information. iglide® V400 iglide® H1 iglide® H4
iglide® X6 iglide® H370
➤ Material table, page 56
Diagram 02 and 03: Recommended maximum surface pressure of
iglide® plain bearings as a function of temperature
Pressure and temperature
Diagram 02 and 03 show the recommended maximum static
100
surface pressure [p] of the iglide® plain bearing as a function of
temperature. When using the plain bearing, the bearing tempera-
ture can be higher than the ambient temperature, due to friction.
Take advantage of the opportunity presented by the predictability 10
of the iglide plain bearing to record these effects in advance, or
®
Wear [µm/km]
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
30 fpm 60 fpm
1.0
Surface speed
In these equations
Oscillating motion v = d1 · π ·
·
360 1.000 s [ ]
2 · ß f m
With increasing load, the coefficient of friction of the plain bearing a= Angle of motion either side of the mean position in
typically decreases. In this context, shaft materials and the surface degrees
d1= Shaft diameter in inches, if mm convert to inches prior to
finish are also significant. With varying speed like seen for example
calculation
with oscillating movements, the value needed is the average speed b= Frequency in cycle per minute
(see formulas to the right). d= Inner diameter in inches, if mm convert to inches prior to
calculation
Continuous
Continuous
Continuous
iglide® plain bearings were primarily developed for low to average
Short
Short
Short
term
term
term
running speeds in continuous operation.
The table shows the permissible surface speed of iglide® plain
bearings for rotating, oscillating, and linear motions. BestSellers
iglide® G300 197 394 138 276 787 984
These surface speeds are limit values assuming minimum
iglide® J 295 591 217 413 1575 1,969
pressure loading of the bearing. In practice, these limit values
iglide® M250 157 394 118 276 492 984
are rarely reached due to an inverse relationship between
iglide® R 157 236 118 197 689 984
load and speed. Each increase of the pressure load leads iglide® L280 (W300)* 197 492 138 354 787 1,181
unavoidably to a reduction of the allowable surface speeds iglide® T500 (X)* 295 689 217 492 984 1,969
and vice versa. General purpose
The limit of the speed is measured by the bearing temperature. iglide® P 197 394 138 276 591 787
This is also the reason why different running speeds can occur iglide® K 197 394 138 276 591 787
for the different movement types. For linear movements, more iglide GLW
®
157 197 118 138 492 591
heat can be dissipated via the shaft, since the bearing uses a Long service life
iglide® J260 197 394 138 276 591 787
longer surface area on the shaft.
iglide J3
®
295 591 217 413 1,575 1,969
iglide® J350 256 591 197 453 787 1,575
Surface speed and wear
iglide L250
®
197 295 138 217 394 591
Considerations about the permissible surface speeds should
iglide® D 295 591 217 413 1,575 1,969
also include the wear resistance of the plain bearing. High iglide® J200 197 295 138 217 1,969 2,953
running speeds automatically bring correspondingly high wear High temperatures
rates with them. iglide® X6 295 689 217 492 1,063 1,969
iglide V400
®
177 256 118 177 394 591
Surface speed and coefficient of friction iglide® Z 295 689 217 492 984 1,181
In practice the coefficient of friction of plain bearings is iglide® UW500 157 295 118 217 394 591
a result of the surface speed. High surface speeds have High media resistance
iglide® H 197 295 138 217 591 787
a higher coefficient of friction than low surface speeds.
iglide® H1 394 492 197 295 984 1,378
Diagram 08 shows this relationship by using the example of a cold
iglide® H370 236 295 157 217 787 984
rolled steel shaft (1050 steel) with a load of 102 psi.
iglide H2
®
177 197 118 138 492 591
Applications with food contact
iglide® A180 157 236 118 197 689 984
pv value iglide® A200 157 295 118 217 394 591
For plain bearings, the product is given a new value depending iglide A350
®
197 236 157 177 492 591
on the specific load (p) and the surface speed (v). The pv value iglide® A500 118 197 79 138 197 394
can be considered a measure of the frictional heat and can iglide® A290 197 394 138 276 591 787
be used as an analytical tool to answer questions concerning iglide T220
®
79 197 59 138 197 394
the proper application of a plain bearing. For this purpose, the Applications with high loads
iglide® Q 197 394 138 276 984 1,181
actual pv value is a function of the shaft material of the ambient
iglide® Q2 197 394 138 276 787 984
temperature and the operating time.
Special application areas
iglide® F 157 295 118 217 591 984
iglide H4
®
197 295 138 217 197 394
iglide® UW 98 295 79 217 394 591
iglide® N54 157 295 118 217 197 394
iglide Q290
®
157 394 118 275 197 394
*W300 is the European material equivalent for iglide® L280, Table 01: Surface speeds of iglide® bearings in ft/s; continuous and
X is the European equivalent material for iglide® T500 short term
pv
perm.
= ( )
[K1 · π · k · ∆T ] [K2 · π · s · ∆T ]
µ · s
+
µ · b1 · 2
· 10–3
Correction factor
The tolerated pv value can be increased in intermittent operation
if the bearing temperature never reaches the maximum limit
where
because of the short operating time. Tests have shown
K1, K2 = constant for heat dissipation
that this is true for operating times below 10 minutes. An
(K1 = 0.5, K2 = 0.042)
important qualifier here is the ratio of the operating time and
s = bearing wall thickness [mm]
pause intervals. It is known that long pauses make a greater
b1 = bearing length [mm]
contribution to re-cooling. The different curves of Diagram 09
µ = coefficient of friction
represent different ratios (3x means that the pause lasts three
s = thermal coductivity of the shaft
times longer than the operating time).
k = thermal coductivity of the bearing
∆T = (Ta – Tu)
Lubrication
Tu = ambient temperature [°F]
Although iglide® plain bearings are designed to run dry, they
Ta = max. application temperature [°F]
are quite compatible with standard oils and greases. A single
lubrication during the installation improves the start-up behavior
Material Thermal conductivity [W/m · k]
and the coefficient of friction, reducing the frictional heat. Due to
Steel 46
this effect, the permissible loads for plain bearings can be increased
Aluminum 204
by lubrication. For further information, please contact us. Table 03
Grey cast iron 58
shows the correction factors for pv value using lubrication
303 Stainless 16
Ceramics 1.4
Temperatures
Plastics 0.24
The tables show the maximum ambient temperatures to which
Table 02: Heat conductivity values of shaft or housing materials
the plain bearings can be exposed for a short-term. If these
The thermal expansion of plastics is approximately 10 to 20 times Diagram 10: Comparison of the continuous and short term upper
application temperature limits [°F]
higher than metals. In contrast to metal, this expansion is non linear
in plastics. The coefficient of thermal expansion of the iglide® plain
bearing is a significant reason for the required play in the bearing. At
Material Temp. [°F] Material Temp. [°F]
the given application clearance, seizing of the bearing to the shaft
iglide G300
®
+176 iglide UW500
®
+302
does not occur at high temperatures. The coefficient of thermal
iglide® J +140 iglide® H +248
expansion of iglide® plain bearings was examined for significant
iglide® M250 +140 iglide® H1 +176
temperature ranges with results given in the individual materials iglide R
®
+122 iglide H370
®
+212
tables at the start of each chapter. iglide® L280 (W300)* +140 iglide® H2 +230
iglide T500 (X)*
®
+275 iglide A180
®
+140
iglide® P +194 iglide® A200 +122
iglide K
®
+158 iglide A350
®
+284
iglide® GLW +176 iglide® A500 +266
iglide® J260 +176 iglide® A290 +230
iglide J3
®
+140 iglide T220
®
+122
iglide® J350 +284 iglide® Q +122
iglide L250
®
+131 iglide Q2
®
+158
iglide® D +122 iglide® F +221
iglide J200
®
+140 iglide H4
®
+230
iglide® X6 +329 iglide® UW +176
iglide® V400 +212 iglide® N54 +140
Picture 08: Material tests are possible up to +482 °F
iglide Z
®
+293 iglide Q290
®
+176
*W300 is the European material equivalent for iglide® L280,
Table 04: Temperature at which additional securing of the iglide® plain
X is the European equivalent material for iglide® T500
bearing is required
Diagram 11: Coefficients of friction of the iglide® plain bearings at Diagram 12: Frictional values of iglide® materials under different loads
the recommended shaft surface roughness and low load, p = 109 psi
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Wear [µm/km]
experiments, the wear is of primary importance as a 1
100
Wear and pressure
Different loads greatly influence the bearing wear. Among
the iglide® plain bearings, certain materials are specialized for
10
Wear [µm/km]
low loads. While others are better suited for high or extremely
high loads. With a hardened, ground shaft, iglide® J can be
characterized as the most wear-resistant bearing material
1
for low loads. iglide® Q, on the other hand, is specialized for 725 1,450 2,901 6,527
extreme loads. Pressure (psi)
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Picture 11: Erosion damage due to shafts that are too smooth
12
Wear and shaft materials
The shaft is, next to the plain bearing itself, the most important 9
L280 (W300)*
bearing, and like the bearing, it is affected by relative motion.
Wear [µm/km]
T500 (X)*
Fundamentally, the shaft is also worn, however, modern bearing
3
M250
G300
A180
systems are designed so that the wear of the shafts is so
J350
H1
X6
J3
P
Z
J
small that it can not be detected with traditional methods of 0
measurement technology. Diagram 15: Wear with 1050 steel shaft,
Shafts can be distinguished and classified according to their p = 145 psi, v = 59 fpm, rms = 9
L280 (W300)*
The hardness of the shaft also plays an important role. When the
Wear [µm/km]
T500 (X)*
shafts are less hard, the shaft is worn smooth during the break-in 3
M250
G300
A180
J350
phase. Abrasive points are worn off and the surface is rebuilt. For
H1
X6
J3
P
Z
J
some materials, this effect has positive influences, and the wear 0
resistance of the plastic bearing increases. Diagram 16: Wear with 304 stainless shaft,
p = 145 psi, v = 59 fpm, rms = 9
In the following diagrams, the most common shaft materials are
listed and the iglide® materials that are best suited are compared.
15
For easier comparison, the scaling of the wear axis is the same in all
diagrams. The small wear results of the systems with hard-chromed 12
shafts are especially impressive. This very hard but smooth shaft
gives excellent results on the wear behavior in many bearing pairs. 9
The wear of many iglide plain bearings is lower on this shaft than
®
6
on any other shaft material tested. However, it should be pointed
L280 (W300)
Wear [µm/km]
3
M250
G300
A180
danger of stick slip on hard chromed shafts is especially high.
J350
H1
X6
J3
P
Z
J
0
Diagram 17: Wear with machinery steel shaft,
p = 145 psi, v = 59 fpm, rms = 9
15
12
6
L280 (W300)
Wear [µm/km]
T500 (X)
3
M250
G300
A180
J350
H1
X6
J3
P
Z
J
0
Diagram 18: Wear with hard chromed 1050 shaft,
Picture 12: Oscillating wear test rig for testing the wear in oscillating p = 145 psi, v = 59 fpm, rms = 9
movements at low loads
6
L280 (W300)* right bearing material. It must be said on the other side, that no
Wear [µm/km]
T500 (X)* other shaft material shows a bigger variation of wear results with
3 different bearing materials. The test results give only a sample of
M250
G300
A180
J350
H1
the existing data. All of the results shown were made with same
X6
J3
P
Z
J
0
loads and speeds.
Diagram 19: Wear with hard chromed aluminum shaft,
p = 145 psi, v = 59 fpm, rms = 9
15
12
6
L280 (W300)*
Wear [µm/km]
T500 (X)*
3
M250
G300
A180
J350
H1
X6
J3
P
Z
J
0
Diagram 20: Wear with a machinery steel shaft,
p = 145 psi, v = 59 fpm, rms = 9
15
Picture 13: Oscillating wear test rig for testing the wear in oscillating
movements at medium loads
12
6
L280 (W300)*
Wear [µm/km]
T500 (X)*
3
M250
G300
A180
J350
H1
X6
J3
P
Z
J
Material UV Material UV
resistance resistance Vacuum
iglide® plain bearings can be used in a vacuum to a limited extent.
iglide® G300 +++++ iglide® H ++
Only a small amount of outgassing takes place. For most iglide®
iglide® J +++ iglide® H1 ++
plain bearings, the outgassing does not change the material
iglide® M250 ++++ iglide® H370 +++++
properties.
iglide® R ++++ iglide® H2 +
iglide® L280 (W300)* +++ iglide® A180 +++
iglide® T500 (X)* +++++ iglide® A200 ++++
Electrical properties
In the product line of the maintenance-free, self-lubricating
iglide® P +++++ iglide® A350 ++++
iglide ® plain bearings, there are both insulating as well
iglide® K ++++ iglide® A500 +++
as electrically conductive materials. The most important
iglide® GLW +++++ iglide® A290 ++++
electrical properties are given in detail in the individual material
iglide® J260 + iglide® T220 ++
descriptions. The adjacent table compares the most important
iglide® J3 +++ iglide® Q ++
electrical properties of iglide® plain bearings.
iglide® J350 ++ iglide® Q2 +++++
iglide® L250 +++ iglide® F +++++
The iglide® plain bearings not mentioned here are electrically
iglide® X6 +++++ iglide® H4 +
insulating. Please observe that for some materials the properties
iglide® V400 +++ iglide® UW +++
can be changed by the material’s absorption of moisture. In
iglide® Z +++ iglide® N54 ++++
experiments, it should be tested whether the desired properties
iglide® UW500 +++++
are also stable when the conditions are changing.
Table 08: UV resistance of iglide® plain bearings
+ low resistance +++++ high resistance
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Dimensions in inches
Dimensions inch 0.0393”/=.1181” >0.1181”/=0.23622” >0.2362”/=0.3937” >0.3937”/=.7086”
H7 inch +0.0000 +0.0004 +0.0000 +0.0005 +0.0000 +0.0006 +0.0000 +0.0007
E 10 inch +0.0006 +0.0021 +0.0008 +0.0027 +0.0010 +0.0033 +0.0013 +0.0040
F 10 inch +0.0002 +0.0018 +0.0004 +0.0023 +0.0005 +0.0028 +0.0006 +0.0034
D 11 inch +0.0008 +0.0031 +0.0012 +0.0041 +0.0016 +0.0051 +0.0020 +0.0063
f6 inch -0.0002 -0.0005 -0.0004 -0.0007 -0.0005 -0.0009 -0.0006 -0.0011
d 13 inch -0.0008 -0.0063 -0.0012 -0.0083 -0.0016 -0.0102 -0.0020 -0.0126
h6 inch -0.0000 -0.0002 -0.0000 -0.0003 -0.0000 -0.0004 -0.0000 -0.0004
h7 inch -0.0000 -0.0004 -0.0000 -0.0005 -0.0000 -0.0006 -0.0000 -0.0007
h9 inch -0.0000 -0.0010 -0.0000 -0.0012 -0.0000 -0.0014 -0.0000 -0.0017
h 13 inch -0.0000 -0.0055 -0.0000 -0.0071 -0.0000 -0.0087 -0.0000 -0.0106
Diagram 22: Positions of the measurement planes Picture 14: Measurement of the inner diameter of a pressfit plain
bearings
Troubleshooting
In spite of careful manufacturing and assembly of the bearings, variances and questions regarding the recommended installation
dimensions and tolerances can result.
For this reason, we have compiled a list of the most frequent reasons for variance. In many cases, with this troubleshooter, the
reasons for the variances can be found quickly.
Symptom Action/Solution
Bearing is oversized before pressfit Check dimensions only after pressfit
Removal of material when pressed into Add chamfer to housing bore, check bore size
housing
Bearing is over/under sized after pressfit Check housing bore dimension, check housing bore material softer
bore materials (plastic, aluminum) can expand upon pressfit
Operating Clearances are too large/small Check ID of bearing after press, housing bore, shaft diameter
Bearing noise/squeak Check shaft surface finish/ Possibly roughen shaft
Bearing wears, material deposits on shaft Operating clearance may be too small/ Increase clearance
Chattering noise Operating clearance too large, excessive speed/Reduce speed and operating clearance
Shaft wear Shaft material too soft/ Change shaft material or hardness, switch
to alternative iglide material
Bearing seizes on shaft Operating clearances too small, temperature or moisture may be causing material expansion
Loss of pressfit Bearings overheated/ Axial secure bearing into housing or select alternative material grade
Adhesion
Using an adhesive to fit an iglide® bearing is not usually necessary.
If the pressfit of the bearing could be lost because of high
temperatures, the use of a plain bearing with a higher temperature
resistance is recommended. If however, the securing of the bearing
by adhesives is planned, individual tests are necessary in each
case. The transfer of successful results to other application cases
20– 30° is not possible.
Machining
iglide® plain bearings are delivered ready to fit. The extensive
product line makes it possible to use a standard dimension in
most cases. If for some reason, a subsequent machining of the
Diagram 23: Pressfit of the bearing (section view) plain bearing is necessary, Table 10 shows the machining standard
values. The subsequent machining of the running surfaces is to be
Process Turning Boring Milling avoided if possible. Higher wear rate is most often the result. An
Tool material SS SS SS
exception is the iglide® M250 which is very suitable for secondary
Feed [mm] 0.1…0.5 0.1…0.5 to 0.5
machining. With other iglide® plain bearings, disadvantages of a
Tool relief angle 5…15 10…12 3
sliding surface machining can be counteracted by lubrication during
Tool rake angle 0…10 3…5
installation. Please also remember that igus® manufactures a range
Cutting speed [m/min] 200…500 50…100 to 1,000
of bar stock materials designed for machining.
Table 10: Guidelines for machining
PT-1350 PT-0620
Press-fitting plain bearings made easy
iglide® plain bearings are pressfit bearings, which are dimensionally
oversized and pressed into a housing with H7 tolerance. This is
not always done in an assembly line using suitable tools. The new
igus® assembly aid flexibly and reliably accepts plain bearings for
shaft diameters from 13–50 mm (PT-1350) and 6–20 mm (PT-0620)
and even permits assembly using a hammer – simple and fast.
Picture 16: igus® pressfit tool
Thick and tough standard: The overall best-seller, iglide® G300, is a cut above the rest
Excellent vibration dampening – in almost all disciplines. In total, more than 2,000 sizes are
iglide® M250 available from stock, ready to ship as early as same day.
➤ Page 135
l Self-lubricating and maintenance-free
l Lightweight
Economic standard: l Good price/performance ratio
Low-cost – l Predictable service life
iglide® R
➤ Page 159
6 materials
Ø 1/8 to 3 inches
more dimensions on request
Ø 1 to 150 mm
mm
more dimensions on request
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Using a specially designed bearing on this centrifugal arm significantly iglide® G300 is typically recommended when an economical bearing
reduced manufacturing costs, while offering maintenance-free is required to handle extremely high loads under low to medium
operation and high wear resistance. surface speeds.
With long service lives, no need for external lubrication, and low cost In this application, eight different iglide® plain bearings are fit in the
compared to conventional bearings, iglide® may offer up to 90% cost pump, producing various pivoting and linear motions in a durable,
savings. cost-effective manner.
The iglide® plastic bearings reduce the overall weight and enhance Temperatures of more than 212º F was no problem for iglide® T500
the mechanical properties of this high speed vehicle. plastic plain bearings.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® G300 l l l l l
iglide® J l l l l l
iglide® M250 l l l l l
iglide® R l l l l
iglide® L280 l l l l l l
iglide® T500 l l l l l l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® G300 l l
iglide® J l l l l
iglide® M250 l l l
iglide® R l l l l
iglide® L280 l l
iglide® T500 l l l l
iglide® G300 83
iglide® J 115
iglide® R 159
iglide® G300 3 3 83
iglide® J 5 3 115
iglide® R 6 1 159
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
83
iglide®
G300 iglide® G300 - General Purpose
Most popular iglide®material worldwide
Cost-effective
Mechanical Properties
Modulus of elasticity psi 1,131,000 DIN 53457
Tensile strength at 68°F psi 30,460 DIN 53452
Compressive strength psi 11,310
Permissible static surface pressure (68°F) psi 11,600
Shore D-hardness 81 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
10
Compressive Strength 9
The graph shows the elastic deformation of iglide® G300 during radial 8
loading. At the maximum permissible load of 11,600 psi, the defor- 7
mation is less than 5%. The plastic deformation is minimal up to a 6
pressure of approximately 14,500 psi. However, it is also a result of 5
Deformation in %
14,500
Permissible Surface Speeds
iglide® G300 has been developed for low to medium surface speeds.
The maximum values shown in the table can only be achieved at low
1,450
pressure loads. At the given speeds, friction can cause a temperature
increase to maximum permissible levels. In practice, though, this
temperature level is rarely reached, due to varying application
conditions.
145
➤ Surface speed, Page 64
➤ pv Value, Page 65
Pressure (psi)
Temperatures 17,400
Application temperatures affect the properties of plain bearings greatly. The 14,500
short-term maximum temperature is 428°F, this allows the use of iglide®
11,600
G300 plain bearings in heat treating applications in which the bearings are
not subjected to additional loading. 8702
Pressure (psi)
5802
With increasing temperatures, the compressive strength of iglide® G300 plain
bearings decreases. The graph shows this inverse relationship. However, 2901
at the long-term maximum temperature of 266°F, the permissible surface
pressure is still above 5,800 psi. 0
68 86 104 122 140 158 176 194 212 230 248 266
The ambient temperatures that are prevalent in applications also has an
effect on the bearing wear. With increasing temperatures, the wear increases Temperature in (°F)
and this effect is notable starting at the temperature of 248°F.
Recommended maximum permissible static surface
pressure of iglide® G300 as a result of temperature
➤ Application temperatures, Page 67
0.25
0.5
Coefficient of friction µ
0.20
0.15
0.4
0.10
Coefficient of friction (µ)
0.3 0.05
0.00
0 1,450 2,901 4,351 5,801 7,252 8,702 10,150 11,600
0.2
Pressure (psi)
0.1 Coefficient of friction of iglide® G300 as a result of
9.84 19.69 29.53 39.37 49.22 59.06 68.90
the load, v = 1.96 fpm
Surface Speed (fpm)
0.5
Coefficient of friction of iglide® G300 as a result of the
running speed; p = 108 psi 0.4
Coefficient of Friction µ
0.3
Oil 0.04
0
Water 0.04 0 20 40 60 80
Shaft Roughness (rms)
Coefficient of friction for iglide ® G300 against steel
Coefficient of friction as result of the shaft surface
(Shaft finish = 40 rms, 50 HRC)
(Shaft - 1050 hard chromed)
Shaft Materials
The graphs show results of testing different shaft materials with plain bearings made of iglide® G300. In the graph below it is observed that iglide®
G300 can be combined with various shaft materials. The simple shaft materials of free-cutting steel and HR Carbon Steel have proven best at low
loads. This helps to design cost-effective systems, since both iglide® G300 and the sliding partner are economically priced.
It is important to note that with increasing loads, the recommended hardness of the
shaft increases. The “soft” shafts tend to wear more easily and thus increase the 12
wear of the overall system. If the loads exceed 290 psi, it is important to recognize 10
that the wear rate (the slope of the curves) clearly decreases with the hard shaft
HR carbon steel
G300 can provide advantages in oscillating movements. The wear of the bearing is
304 Stainless
Wear (µm/km)
4
1050 Steel
smaller for equivalent conditions. The higher the load, the larger the difference. This
means that iglide® G300 can be used for oscillating movements that are well above 2
440B
the given maximum load of 11,600 psi. For these loads, the use of hardened shafts
0
is recommended. In addition to the shaft materials presented here, many others have
been tested. If the shaft material you plan on using is not contained in the test results
Wear of iglide® G300, rotating with different shaft
presented here, please contact us.
materials, load p = 145 psi, v = 59 fpm
16 180
14 160
12 140
120
10
100
8
80
Wear (µm/km)
6
Wear (µm/km)
60
4
40
2
20
0
0
0 145 290 435 580 725
0 1450 2900 4350 5800 7250 8700 10150 11600
Pressure (psi)
Pressure (psi)
1050 Steel 304 Stainless
Rotating Oscillating
HR carbon steel Hard chromed
Wear for pivoting and rotating applications with shaft
Wear with different shaft materials in rotational material 1050 hard chromed, as a result of the load
operation, as a result of the load
Medium Resistance
Chemical resistance of iglide® G300 Effect of moisture absorption on iglide® G300 plain bearings
All data given concerns the chemical resistance at room temperature
(68°F). For a complete list, see Page 1364
Radiation Resistance
Plain bearings made from iglide® G300 are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® G300 plain bearings are permanently resistant to UV-radiation.
Vacuum
iglide® G300 plain bearings outgas in a vacuum. Use in a vacuum environment is only possible for dehumidified bearings.
d2 Type Dimensions
A A Order key
30° G S I -01 03-02
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Type Dimensions
A A
d2
Order key
30° G S I -01 03-02
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
d2 Type Dimensions
A A Order key
30° G S I -01 03-02
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
d2 Type Dimensions
A
A d1
Order key
30° G F I -02 03-02
b1
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 87
Inch
*Based on steel housing bore
GFI-0203-02 1/8 3/16 1/8 .312 .032 .1873 .1878 .1236 .1243
GFI-0203-03 1/8 3/16 3/16 .312 .032 .1873 .1878 .1236 .1243
.1251 .1269
GFI-0203-04 1/8 3/16 1/4 .312 .032 .1873 .1878 .1236 .1243
GFI-0203-06 1/8 3/16 3/8 .312 .032 .1873 .1878 .1236 .1243
GFI-0304-04 3/16 1/4 1/4 .375 .032 .2497 .2503 .1858 .1865
GFI-0304-06 3/16 1/4 3/8 .375 .032 .1873 .1892 .2497 .2503 .1858 .1865
GFI-0304-08 3/16 1/4 1/2 .375 .032 .2497 .2503 .1858 .1865
GFI-0405-2.4 1/4 5/16 5/32 .500 .032 .3122 .3128 .2481 .2490
GFI-0405-04 1/4 5/16 1/4 .500 .032 .3122 .3128 .2481 .2490
GFI-0405-05 1/4 5/16 5/16 .500 .032 .3122 .3128 .2481 .2490
.2498 .2521
GFI-0405-06 1/4 5/16 3/8 .500 .032 .3122 .3128 .2481 .2490
GFI-0405-08 1/4 5/16 1/2 .500 .032 .3122 .3128 .2481 .2490
GFI-0405-12 1/4 5/16 3/4 .500 .032 .3122 .3128 .2481 .2490
GFI-0506-03 5/16 3/8 3/16 .562 .032 .3747 .3753 .3106 .3115
GFI-0506-04 5/16 3/8 1/4 .562 .032 .3747 .3753 .3106 .3115
GFI-0506-06 5/16 3/8 3/8 .562 .032 .3125 .3148 .3747 .3753 .3106 .3115
GFI-0506-08 5/16 3/8 1/2 .562 .032 .3747 .3753 .3106 .3115
GFI-0506-12 5/16 3/8 3/4 .562 .032 .3747 .3753 .3106 .3115
GFI-0607-04 3/8 15/32 1/4 .687 .046 .4684 .4691 .3731 .3740
GFI-0607-05 3/8 15/32 5/16 .687 .046 .4684 .4691 .3731 .3740
GFI-0607-06 3/8 15/32 3/8 .687 .046 .4684 .4691 .3731 .3740
.3750 .3773
GFI-0607-08 3/8 15/32 1/2 .687 .046 .4684 .4691 .3731 .3740
GFI-0607-12 3/8 15/32 3/4 .687 .046 .4684 .4691 .3731 .3740
GFI-0607-14 3/8 15/32 7/8 .687 .046 .4684 .4691 .3731 .3740
GFI-0708-04 7/16 17/32 1/4 .750 .046 .5309 .5316 .4355 .4365
.4379 .4406
GFI-0708-08 7/16 17/32 1/2 .750 .046 .5309 .5316 .4355 .4365
GFI-0809-02 1/2 19/32 1/8 .875 .046 .5934 .5941 .4980 .4990
GFI-0809-04 1/2 19/32 1/4 .875 .046 .5934 .5941 .4980 .4990
GFI-0809-05 1/2 19/32 5/16 .875 .046 .5934 .5941 .4980 .4990
GFI-0809-06 1/2 19/32 3/8 .875 .046 .5003 .5030 .5934 .5941 .4980 .4990
GFI-0809-08 1/2 19/32 1/2 .875 .046 .5934 .5941 .4980 .4990
GFI-0809-12 1/2 19/32 3/4 .875 .046 .5934 .5941 .4980 .4990
GFI-0809-16 1/2 19/32 1 .875 .046 .5934 .5941 .4980 .4990
GFI-1011-06 5/8 23/32 3/8 .937 .046 .7184 .7192 .6230 .6240
GFI-1011-08 5/8 23/32 1/2 .937 .046 .7184 .7192 .6230 .6240
.6253 .6280
GFI-1011-12 5/8 23/32 3/4 .937 .046 .7184 .7192 .6230 .6240
GFI-1011-14 5/8 23/32 7/8 .937 .046 .7184 .7192 .6230 .6240
d2 Type Dimensions
A
A d1
Order key
30° G F I -02 03-02
b1
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 87
Inch
*Based on steel housing bore
d2 Type Dimensions
A
A d1
Order key
30° G F I -02 03-02
b1
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 87
Inch
*Based on steel housing bore
GFI-2831-32 1 3/4 1 15/16 2 2.375 .093 1.7508 1.7547 1.9371 1.9381 1.7471 1.7487
GFI-3235-16 2 2 3/16 1 2.625 .093 2.1871 2.1883 1.9969 1.9981
GFI-3235-24 2 2 3/16 1 1/2 2.625 .093 2.0012 2.0059 2.1871 2.1883 1.9969 1.9981
GFI-3235-32 2 2 3/16 2 2.625 .093 2.1871 2.1883 1.9969 1.9981
GFI-3639-32 2 1/4 2 7/16 2 2.750 .093 2.2531 2.2577 2.4365 2.4377 2.2489 2.2507
GFI-4043-32 2 1/2 2 11/16 2 3.125 .093 2.5035 2.5082 2.6869 2.6881 2.4971 2.5000
GFI-4447-32 2 3/4 2 15/16 2 3.375 .093 2.7523 2.7570 2.9358 2.9370 2.7471 2.7500
d1
Type Dimensions
S
Order key
d2 G T I -04 08- 005
d6
Thickness s (inch)
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
Form T (washer)
iglide® material
h
d5
d4
Inch
d6
Part Number d1 d2 s d4 d5 h d6
h
+.010 -.010 -.0020 +-.005 +.015 +.005 +.008 +.005
Type Dimensions
A A
d2
Order key
30°
G S M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
GSM-0103-02 1.5 3.0 2.0 1.514 1.554 3.000 3.010 1.475 1.500
GSM-0203-03 2.0 3.5 3.0 2.014 2.054 3.500 3.510 1.975 2.000
GSM-02504-05 2.5 4.5 5.0 2.514 2.554 4.500 4.510 2.475 2.500
GSM-0304-03 3.0 4.5 3.0 4.500 4.512 2.975 3.000
GSM-0304-05 3.0 4.5 5.0 4.500 4.512 2.975 3.000
3.014 3.054
GSM-0304-06 3.0 4.5 6.0 4.500 4.512 2.975 3.000
GSM-0304-16 3.0 4.5 16.0 4.500 4.512 2.975 3.000
GSM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
4.020 4.068
GSM-0405-06 4.0 5.5 6.0 5.500 5.512 3.970 4.000
GSM-0406-08 4.5 6.0 8.0 4.520 4.568 6.000 6.012 4.470 4.500
GSM-0407-05 4.0 7.0 5.5 4.020 4.068 7.000 7.015 3.970 4.000
GSM-0506-03 5.0 6.0 3.0 6.000 6.012 4.970 5.000
GSM-0506-046 5.0 6.0 4.6 6.000 6.012 4.970 5.000
5.010 5.040
GSM-0506-05 5.0 6.0 5.0 6.000 6.012 4.970 5.000
GSM-0506-07 5.0 6.0 7.0 6.000 6.012 4.970 5.000
GSM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
GSM-0507-07 5.0 7.0 7.0 7.000 7.015 4.970 5.000
5.020 5.068
GSM-0507-08 5.0 7.0 8.0 7.000 7.015 4.970 5.000
GSM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
GSM-0607-06 6.0 7.0 6.0 7.000 7.015 5.970 6.000
GSM-0607-12 6.0 7.0 12.0 7.000 7.015 5.970 6.000
GSM-0607-17 6.0 7.0 17.0 6.010 6.040 7.000 7.015 5.970 6.000
GSM-0607-17.5 6.0 7.0 17.5 7.000 7.015 5.970 6.000
GSM-0607-19 6.0 7.0 19.0 7.000 7.015 5.970 6.000
GSM-0608-025 6.0 8.0 2.5 8.000 8.015 5.970 6.000
GSM-0608-03 6.0 8.0 3.0 8.000 8.015 5.970 6.000
GSM-0608-04 6.0 8.0 4.0 8.000 8.015 5.970 6.000
GSM-0608-05 6.0 8.0 5.0 8.000 8.015 5.970 6.000
GSM-0608-055 6.0 8.0 5.5 8.000 8.015 5.970 6.000
GSM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
GSM-0608-08 6.0 8.0 8.0 8.000 8.015 5.970 6.000
GSM-0608-09 6.0 8.0 9.5 8.000 8.015 5.970 6.000
GSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
GSM-0608-11 6.0 8.0 11.8 8.000 8.015 5.970 6.000
GSM-0608-13 6.0 8.0 13.8 8.000 8.015 5.970 6.000
GSM-0708-07 7.0 8.0 7.0 8.000 8.015 6.964 7.000
7.013 7.049
GSM-0708-10 7.0 8.0 10.0 8.000 8.015 6.964 7.000
d2 Type Dimensions
A A Order key
30° G S M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
GSM-0708-19 7.0 8.0 19.0 7.013 7.049 8.000 8.015 6.964 7.000
GSM-0709-05 7.0 9.0 5.0 9.000 9.015 6.964 7.000
GSM-0709-08 7.0 9.0 8.0 9.000 9.015 6.964 7.000
GSM-0709-09 7.0 9.0 9.0 7.025 7.083 9.000 9.015 6.964 7.000
GSM-0709-10 7.0 9.0 10.0 9.000 9.015 6.694 7.000
GSM-0709-12 7.0 9.0 12.0 9.000 9.015 6.694 7.000
GSM-0809-03 8.0 9.0 3.0 9.000 9.015 7.964 8.000
GSM-0809-05 8.0 9.0 5.0 9.000 9.015 7.964 8.000
GSM-0809-06 8.0 9.0 6.0 8.013 8.049 9.000 9.015 7.964 8.000
GSM-0809-08 8.0 9.0 8.0 9.000 9.015 7.964 8.000
GSM-0809-12 8.0 9.0 12.0 9.000 9.015 7.964 8.000
GSM-0810-05 8.0 10.0 5.0 10.000 10.015 7.964 8.000
GSM-0810-06 8.0 10.0 6.0 10.000 10.015 7.964 8.000
GSM-0810-07 8.0 10.0 7.0 10.000 10.015 7.964 8.000
GSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
GSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
GSM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
GSM-0810-13 8.0 10.0 13.0 10.000 10.015 7.964 8.000
8.025 8.083
GSM-0810-14 8.0 10.0 14.0 10.000 10.015 7.964 8.000
GSM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
GSM-0810-16 8.0 10.0 16.0 10.000 10.015 7.964 8.000
GSM-0810-18 8.0 10.0 18.0 10.000 10.015 7.964 8.000
GSM-0810-20 8.0 10.0 20.0 10.000 10.015 7.964 8.000
GSM-0810-22 8.0 10.0 22.0 10.000 10.015 7.964 8.000
GSM-0810-25 8.0 10.0 25.0 10.000 10.015 7.964 8.000
GSM-0910-12 9.0 10.0 12.0 10.000 10.015 8.964 9.000
9.013 9.049
GSM-0910-16 9.0 10.0 16.0 10.000 10.015 8.964 9.000
GSM-0911-06 9.0 11.0 6.0 11.000 11.018 8.964 9.000
9.025 9.083
GSM-0911-20 9.0 11.0 20.0 11.000 11.018 8.964 9.000
GSM-1011-06 10.0 11.0 6.0 11.000 11.018 9.964 10.000
GSM-1011-07 10.0 11.0 7.0 11.000 11.018 9.964 10.000
GSM-1011-10 10.0 11.0 10.0 11.000 11.018 9.964 10.000
10.013 10.049
GSM-1011-20 10.0 11.0 20.0 11.000 11.018 9.964 10.000
GSM-1011-25 10.0 11.0 25.0 11.000 11.018 9.964 10.000
GSM-1011-30 10.0 11.0 30.0 11.000 11.018 9.964 10.000
GSM-1012-04 10.0 12.0 4.0 12.000 12.018 9.964 10.000
10.025 10.083
GSM-1012-045 10.0 12.0 4.5 12.000 12.018 9.964 10.000
Type Dimensions
A A
d2
Order key
30°
G S M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
d2 Type Dimensions
A A Order key
30° G S M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Type Dimensions
A A
d2
Order key
30°
G S M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
d2 Type Dimensions
A A Order key
30° G S M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Type Dimensions
A A
d2
Order key
30°
G S M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
d2 Type Dimensions
A A Order key
30° G S M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Type Dimensions
A
d2
Order key
A d1
30°
G F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-0304-02 3.0 4.5 7.5 2.0 0.75 4.500 4.512 2.975 3.000
GFM-0304-0275 3.0 4.5 7.0 2.75 0.75 4.500 4.512 2.975 3.000
GFM-0304-03 3.0 4.5 7.5 3.0 0.75 3.014 3.054 4.500 4.512 2.975 3.000
GFM-0304-05 3.0 4.5 7.5 5.0 0.75 4.500 4.512 2.975 3.000
GFM-030407-05 3.0 4.5 7.0 5.0 0.75 4.500 4.512 2.975 3.000
GFM-0405-03 4.0 5.5 9.5 3.0 0.75 5.500 5.512 3.970 4.000
GFM-0405-04 4.0 5.5 9.5 4.0 0.75 5.500 5.512 3.970 4.000
4.020 4.068
GFM-0405-06 4.0 5.5 9.5 6.0 0.75 5.500 5.512 3.970 4.000
GFM-040508-10 4.0 5.5 8.0 10.0 0.75 5.500 5.512 3.970 4.000
GFM-0506-035 5.0 6.0 10.0 3.5 0.5 6.000 6.012 4.970 5.000
GFM-0506-04 5.0 6.0 10.0 4.0 0.5 6.000 6.012 4.970 5.000
GFM-0506-05 5.0 6.0 10.0 5.0 0.5 5.010 5.040 6.000 6.012 4.970 5.000
GFM-0506-06 5.0 6.0 10.0 6.0 0.5 6.000 6.012 4.970 5.000
GFM-0506-15 5.0 6.0 10.0 15.25 0.5 6.000 6.012 4.970 5.000
GFM-0507-03 5.0 7.0 11.0 3.5 1.0 7.000 7.015 4.970 5.000
GFM-0507-04 5.0 7.0 11.0 4.0 1.0 7.000 7.015 4.970 5.000
GFM-0507-05 5.0 7.0 11.0 5.0 1.0 7.000 7.015 4.970 5.000
GFM-0507-07 5.0 7.0 11.0 7.0 1.0 7.000 7.015 4.970 5.000
5.020 5.068
GFM-0507-11 5.0 7.0 11.0 11.0 1.0 7.000 7.015 4.970 5.000
GFM-0507-30 5.0 7.0 11.0 30.0 1.0 7.000 7.015 4.970 5.000
GFM-050715-04 5.0 7.0 15.0 4.0 1.0 7.000 7.015 4.970 5.000
GFM-050709-05 5.0 7.0 9.0 5.0 1.0 7.000 7.015 4.970 5.000
GFM-0607-06 6.0 7.0 11.0 6.0 0.5 7.000 7.015 5.970 6.000
GFM-0607-10 6.0 7.0 11.0 10.0 0.5 6.010 6.040 7.000 7.015 5.970 6.000
GFM-0607-024 6.0 7.0 11.0 2.4 0.5 7.000 7.015 5.970 6.000
GFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-048 6.0 8.0 12.0 4.8 1.0 8.000 8.015 5.970 6.000
GFM-0608-05 6.0 8.0 12.0 5.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-07 6.0 8.0 12.0 7.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
6.020 6.068
GFM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
GFM-060810-08 6.0 8.0 10.0 8.0 1.0 8.000 8.015 5.970 6.000
GFM-060812-20 6.0 8.0 12.0 20.0 1.0 8.000 8.015 5.970 6.000
GFM-060814-12 6.0 8.0 14.0 12.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-25 6.0 8.0 12.0 25.0 1.0 8.000 8.015 5.970 6.000
GFM-0608-35 6.0 8.0 12.0 35.0 1.0 8.000 8.015 5.970 6.000
104
iglide® G300 - Product Range iglide®
G300
Flange bearing - Metric
d2 Type Dimensions
A
A d1
Order key
30° G F M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-0708-03 7.0 8.0 12.0 3.0 0.5 8.000 8.015 6.964 7.000
GFM-0708-06 7.0 8.0 12.0 6.0 0.5 7.013 7.049 8.000 8.015 6.964 7.000
GFM-0708-08 7.0 8.0 12.0 8.0 0.5 8.000 8.015 6.964 7.000
GFM-0709-03.5 7.0 9.0 15.0 3.5 1.0 9.000 9.015 6.964 7.000
GFM-0709-06 7.0 9.0 15.0 6.0 1.0 9.000 9.015 6.964 7.000
GFM-0709-10 7.0 9.0 15.0 10.0 1.0 7.025 7.083 9.000 9.015 6.964 7.000
GFM-0709-12 7.0 9.0 15.0 12.0 1.0 9.000 9.015 6.964 7.000
GFM-070919-10 7.0 9.0 19.0 10.0 1.0 9.000 9.015 6.964 7.000
GFM-0809-03 8.0 9.0 15.0 3.0 0.5 9.000 9.015 7.964 8.000
GFM-0809-035 8.0 9.0 13.0 3.5 0.5 9.000 9.015 7.964 8.000
GFM-0809-055 8.0 9.0 13.0 5.5 0.5 8.013 8.049 9.000 9.015 7.964 8.000
GFM-0809-08 8.0 9.0 13.0 8.0 0.5 9.000 9.015 7.964 8.000
GFM-0809-12 8.0 9.0 13.0 12.0 0.5 9.000 9.015 7.964 8.000
GFM-0810-02 8.0 10.0 15.0 2.7 1.0 10.000 10.015 7.964 8.000
GFM-0810-03 8.0 10.0 15.0 3.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-035 8.0 10.0 15.0 3.5 1.0 10.000 10.015 7.964 8.000
GFM-0810-04 8.0 10.0 15.0 4.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
GFM-0810-06 8.0 10.0 15.0 6.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-065 8.0 10.0 15.0 6.5 1.0 10.000 10.015 7.964 8.000
GFM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
GFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
GFM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-11 8.0 10.0 15.0 11.0 1.0 10.000 10.015 7.964 8.000
8.025 8.083
GFM-0810-15 8.0 10.0 15.0 15.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-25 8.0 10.0 15.0 25.0 1.0 10.000 10.015 7.964 8.000
GFM-0810-30 8.0 10.0 15.0 30.0 1.0 10.000 10.015 7.964 8.000
GFM-081013-08 8.0 10.0 13.0 8.0 1.0 10.000 10.015 7.964 8.000
GFM-081014-05 8.0 10.0 14.0 5.0 1.0 10.000 10.015 7.964 8.000
GFM-081014-06 8.0 10.0 14.0 6.0 1.0 10.000 10.015 7.964 8.000
GFM-081014-08 8.0 10.0 14.0 8.0 1.0 10.000 10.015 7.964 8.000
GFM-081014-10 8.0 10.0 14.0 10.0 1.0 10.000 10.015 7.964 8.000
GFM-081016-11 8.0 10.0 16.0 11.0 1.0 10.000 10.015 7.964 8.000
GFM-081016-15 8.0 10.0 16.0 15.0 1.0 10.000 10.015 7.964 8.000
GFM-081017-15 8.0 10.0 17.0 15.0 1.0 10.000 10.015 7.964 8.000
GFM-0811-07 8.0 11.0 18.0 7.0 1.0 8.150 8.210 11.000 11.018 8.089 8.125
GFM-0910-065 9.0 10.0 15.0 6.5 0.5 9.013 9.049 10.000 10.015 8.964 9.000
105
iglide®
G300
iglide® G300 - Product Range
Flange bearing - Metric
Type Dimensions
A
d2
Order key
A d1
30°
G F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-0910-17 9.0 10.0 15.0 17.5 0.5 9.013 9.049 10.000 10.015 8.964 9.000
GFM-1011-026 10.0 11.0 15.0 2.6 0.5 11.000 11.015 9.964 10.000
GFM-1011-03 10.0 11.0 15.0 3.5 0.5 11.000 11.015 9.964 10.000
10.013 10.049
GFM-1011-044 10.0 11.0 15.0 4.4 0.5 11.000 11.015 9.964 10.000
GFM-1011-10 10.0 11.0 15.0 10.0 0.5 11.000 11.015 9.964 10.000
GFM-1012-035 10.0 12.0 18.0 3.5 1.0 12.000 12.018 9.964 10.000
GFM-1012-04 10.0 12.0 18.0 4.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-06 10.0 12.0 18.0 6.0 1.0 12.000 12.018 9.964 10.000
GFM-101214-06 10.0 12.0 14.0 6.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-12 10.0 12.0 18.0 12.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
GFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
GFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
GFM-101216-06 10.0 12.0 16.0 6.0 1.0 12.000 12.018 9.964 10.000
GFM-101214-07 10.0 12.0 14.0 7.0 1.0 12.000 12.018 9.964 10.000
GFM-101216-09 10.0 12.0 16.0 9.0 1.0 12.000 12.018 9.964 10.000
GFM-101216-10 10.0 12.0 16.0 10.0 1.0 12.000 12.018 9.964 10.000
GFM-101215-12 10.0 12.0 15.0 12.0 1.0 12.000 12.018 9.964 10.000
GFM-101216-15 10.0 12.0 16.0 15.0 1.0 12.000 12.018 9.964 10.000
GFM-1013-12 10.0 13.0 20.0 12.0 1.5 10.025 10.083 13.000 13.018 9.964 10.000
GFM-111320-037 11.0 13.0 20.0 3.7 1.0 11.032 11.102 13.000 13.018 10.957 11.000
GFM-1213-03 12.0 13.0 17.0 3.0 0.5 13.000 13.018 11.957 12.000
GFM-1213-12 12.0 13.0 17.0 12.0 0.5 12.016 12.059 13.000 13.018 11.957 12.000
GFM-121315-12 12.0 13.0 15.0 12.0 1.0 13.000 13.018 11.957 12.000
GFM-1214-03 12.0 14.0 20.0 3.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-05 12.0 14.0 20.0 5.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-06 12.0 14.0 20.0 6.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
GFM-1214-10 12.0 14.0 20.0 10.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-11 12.0 14.0 20.0 11.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
106
iglide® G300 - Product Range iglide®
G300
Flange bearing - Metric
d2 Type Dimensions
A
A d1
Order key
30° G F M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-24 12.0 14.0 20.0 24.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-31 12.0 14.0 20.0 31.0 1.0 14.000 14.018 11.957 12.000
GFM-1214-40 12.0 14.0 20.0 40.0 1.0 14.000 14.018 11.957 12.000
GFM-121416-034 12.0 14.0 16.0 3.4 1.0 14.000 14.018 11.957 12.000
GFM-121418-04 12.0 14.0 18.0 4.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
GFM-121418-08 12.0 14.0 18.0 8.0 1.0 14.000 14.018 11.957 12.000
GFM-121418-10 12.0 14.0 18.0 10.0 1.0 14.000 14.018 11.957 12.000
GFM-121418-12 12.0 14.0 18.0 12.0 1.0 14.000 14.018 11.957 12.000
GFM-121418-15 12.0 14.0 18.0 15.0 1.0 14.000 14.018 11.957 12.000
GFM-121418-20 12.0 14.0 18.0 20.0 1.0 14.000 14.018 11.957 12.000
GFM-1315-06 13.0 15.0 22.0 6.0 1.0 15.000 15.018 12.957 13.000
13.032 13.102
GFM-1315-08 13.0 15.0 22.0 8.0 1.0 15.000 15.018 12.957 13.000
GFM-1416-03 14.0 16.0 22.0 3.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-04 14.0 16.0 22.0 4.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-05 14.0 16.0 22.0 5.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-06 14.0 16.0 22.0 6.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-08 14.0 16.0 22.0 8.0 1.0 16.000 16.018 13.957 14.000
14.032 14.102
GFM-1416-10 14.0 16.0 22.0 10.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
GFM-1416-21 14.0 16.0 22.0 21.0 1.0 16.000 16.018 13.957 14.000
GFM-141624-16 14.0 16.0 24.0 16.0 1.0 16.000 16.018 13.957 14.000
GFM-1516-02 15.0 16.0 20.0 2.0 0.5 16.000 16.018 14.957 15.000
GFM-1516-025 15.0 16.0 20.0 2.5 0.5 16.000 16.018 14.957 15.000
15.016 15.059
GFM-1516-03 15.0 16.0 20.0 3.0 0.5 16.000 16.018 14.957 15.000
GFM-1516-15 15.0 16.0 20.0 15.0 0.5 16.000 16.018 14.957 15.000
GFM-1517-04 15.0 17.0 23.0 4.0 1.0 17.000 17.018 14.957 15.000
GFM-1517-045 15.0 17.0 23.0 4.5 1.0 17.000 17.018 14.957 15.000
GFM-1517-05 15.0 17.0 23.0 5.0 1.0 17.000 17.018 14.957 15.000
GFM-1517-09 15.0 17.0 23.0 9.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
GFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
GFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
GFM-1517-20 15.0 17.0 23.0 20.0 1.0 17.000 17.018 14.957 15.000
GFM-151824-32 15.0 18.0 24.0 32.0 1.5 15.032 15.102 18.000 18.018 14.957 15.000
GFM-1618-04 16.0 18.0 24.0 4.0 1.0 18.000 18.018 15.957 16.000
16.032 16.102
GFM-1618-06 16.0 18.0 24.0 6.0 1.0 18.000 18.018 15.957 16.000
107
iglide®
G300
iglide® G300 - Product Range
Flange bearing - Metric
Type Dimensions
A
d2
Order key
A d1
30°
G F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-1618-09 16.0 18.0 24.0 9.0 1.0 18.000 18.018 15.957 16.000
GFM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.032 16.102
GFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
GFM-1618-21 16.0 18.0 24.0 21.0 1.0 18.000 18.018 15.957 16.000
GFM-1622-12 16.0 22.0 25.0 12.0 1.0 16.032 16.102 22.000 22.021 15.957 16.000
GFM-1719-09 17.0 19.0 25.0 9.0 1.0 19.000 19.021 16.957 17.000
GFM-1719-16 17.0 19.0 25.0 16.0 1.0 17.032 17.102 19.000 19.021 16.957 17.000
GFM-1719-25 17.0 19.0 25.0 25.0 1.0 19.000 19.021 16.957 17.000
GFM-1820-04 18.0 20.0 26.0 4.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-06 18.0 20.0 26.0 6.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-09 18.0 20.0 26.0 9.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-11 18.0 20.0 26.0 11.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
18.032 18.102
GFM-1820-17 18.0 20.0 26.0 17.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-30 18.0 20.0 26.0 30.0 1.0 20.000 20.021 17.957 18.000
GFM-1820-32 18.0 20.0 26.0 32.0 1.0 20.000 20.021 17.957 18.000
GFM-182022-06 18.0 20.0 22.0 6.0 1.0 22.000 22.021 17.957 18.000
GFM-1822-28 18.0 22.0 26.0 28.0 2.0 18.032 18.102 22.000 22.021 17.957 18.000
GFM-2021-035 20.0 21.0 25.0 3.5 0.5 21.000 21.021 19.948 20.000
GFM-2021-15 20.0 21.0 25.0 15.0 0.5 20.020 20.072 21.000 21.021 19.948 20.000
GFM-2021-20 20.0 21.0 25.0 20.0 0.5 21.000 21.021 19.948 20.000
GFM-2023-07 20.0 23.0 30.0 7.0 1.5 23.000 23.021 19.948 20.000
GFM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
GFM-2023-16 20.0 23.0 30.0 16.5 1.5 23.000 23.021 19.948 20.000
GFM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
GFM-202329-20 20.0 23.0 30.0 20.0 1.5 23.000 23.021 19.948 20.000
GFM-202326-21 20.0 23.0 26.0 21.0 1.5 23.000 23.021 19.948 20.000
GFM-202328-15 20.0 23.0 28.0 15.0 1.5 23.000 23.021 19.948 20.000
GFM-2427-07 24.0 27.0 32.0 7.0 1.5 27.000 27.021 23.948 24.000
24.040 24.124
GFM-2427-10 24.0 27.0 32.0 10.5 1.5 27.000 27.021 23.948 24.000
GFM-2526-25 25.0 26.0 30.0 25.0 0.5 25.020 25.072 26.000 26.021 24.948 25.000
GFM-2527-48 25.0 27.0 32.0 48.0 1.0 25.040 25.124 27.000 27.021 24.948 25.000
GFM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
GFM-2528-16 25.0 28.0 35.0 16.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
GFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
GFM-2630-12 26.0 30.0 37.0 12.0 2.0 26.040 26.124 30.000 30.021 25.948 26.000
108
iglide® G300 - Product Range iglide®
G300
Flange bearing - Metric
d2 Type Dimensions
A
A d1
Order key
30° G F M -01 03-02
b1
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-2730-20 27.0 30.0 35.0 20.0 1.5 27.040 27.124 30.000 30.021 26.948 27.000
GFM-2830-10 28.0 30.0 35.0 10.0 1.0 30.000 30.021 27.948 28.000
GFM-2830-36 28.0 30.0 35.0 36.0 1.0 28.040 28.124 30.000 30.021 27.948 28.000
GFM-2830-48 28.0 30.0 35.0 48.0 1.0 30.000 30.021 27.948 28.000
GFM-283239-20 28.0 32.0 39.0 20.0 2.0 28.040 28.124 32.000 32.025 27.948 28.000
GFM-3031-20 30.0 31.0 36.0 20.0 0.5 31.000 31.025 29.948 30.000
30.040 30.124
GFM-3031-30 30.0 31.0 35.0 30.0 0.5 31.000 31.025 29.948 30.000
GFM-3032-04 30.0 32.0 37.0 4.0 1.0 32.000 32.025 29.948 30.000
GFM-3032-12 30.0 32.0 37.0 12.0 1.0 32.000 32.025 29.948 30.000
30.040 30.124
GFM-3032-17 30.0 32.0 37.0 17.5 1.0 32.000 32.025 29.948 30.000
GFM-3032-22 30.0 32.0 37.0 22.0 1.0 32.000 32.025 29.948 30.000
GFM-3034-09 30.0 34.0 42.0 9.0 2.0 34.000 34.025 29.948 30.000
GFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
GFM-3034-20 30.0 34.0 42.0 20.0 2.0 34.000 34.025 29.948 30.000
30.040 30.124
GFM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.940 30.000
GFM-3034-37 30.0 34.0 42.0 37.0 2.0 34.000 34.025 29.948 30.000
GFM-303440-10 30.0 34.0 40.0 10.0 2.0 34.000 34.025 29.948 30.000
GFM-3236-16 32.0 36.0 40.0 16.0 2.0 36.000 36.025 31.938 32.000
32.050 32.150
GFM-3236-26 32.0 36.0 40.0 26.0 2.0 36.000 36.025 31.938 32.000
GFM-343850-35 34.0 38.0 50.0 35.0 2.0 34.050 34.150 38.000 38.025 34.938 34.000
GFM-3539-058 35.0 39.0 47.0 5.8 2.0 39.000 39.025 34.938 35.000
GFM-3539-07 35.0 39.0 47.0 7.0 2.0 39.000 39.025 34.938 35.000
GFM-3539-16 35.0 39.0 47.0 16.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
GFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
GFM-3539-36 35.0 39.0 47.0 36.0 2.0 39.000 39.025 34.938 35.000
GFM-354051-30 35.0 40.0 51.0 30.0 2.5 35.050 35.150 40.000 40.025 34.938 35.000
GFM-3842-22 38.0 42.0 54.0 22.0 2.0 38.050 38.150 42.000 42.025 37.938 38.000
GFM-4044-07 40.0 44.0 52.0 7.0 2.0 44.000 44.025 39.938 40.000
GFM-4044-14 40.0 44.0 52.0 14.0 2.0 44.000 44.025 39.938 40.000
GFM-4044-20 40.0 44.0 52.0 20.0 2.0 44.000 44.025 39.938 40.000
40.050 40.150
GFM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
GFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
GFM-4044-50 40.0 44.0 52.0 50.0 2.0 44.000 44.025 39.938 40.000
GFM-4246-19 42.0 46.0 53.0 19.0 2.0 42.050 42.150 46.000 46.025 41.938 42.000
GFM-4550-30 45.0 50.0 58.0 30.0 2.0 50.000 50.025 44.938 45.000
45.050 45.150
GFM-4550-50 45.0 50.0 58.0 50.0 2.0 50.000 50.025 44.938 45.000
GFM-5055-07 50.0 55.0 63.0 7.0 2.0 50.050 50.150 55.000 55.030 49.938 50.000
109
iglide®
G300
iglide® G300 - Product Range
Flange bearing - Metric
Type Dimensions
A
d2
Order key
A d1
30°
G F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 87
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GFM-5055-10 50.0 55.0 63.0 10.0 2.0 55.000 55.030 49.938 50.000
GFM-5055-18 50.0 55.0 63.0 18.0 2.0 55.000 55.030 49.938 50.000
GFM-5055-25 50.0 55.0 63.0 25.0 2.0 50.050 50.150 55.000 55.030 49.938 50.000
GFM-5055-40 50.0 55.0 63.0 40.0 2.0 55.000 55.030 49.938 50.000
GFM-5055-50 50.0 55.0 63.0 50.0 2.0 55.000 55.030 49.938 50.000
GFM-6065-07 60.0 65.0 73.0 7.0 2.0 65.000 65.030 59.926 60.000
GFM-6065-22 60.0 65.0 73.0 22.0 2.0 65.000 65.030 59.926 60.000
GFM-6065-30 60.0 65.0 73.0 30.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
GFM-6065-50 60.0 65.0 73.0 50.0 2.0 65.000 65.030 59.926 60.000
GFM-606580-62 60.0 65.0 80.0 62.0 2.0 65.000 65.030 59.926 60.000
GFM-6570-50 65.0 70.0 78.0 50.0 2.0 65.060 65.180 70.000 70.030 64.926 65.000
GFM-7075-50 70.0 75.0 83.0 50.0 2.0 70.060 70.180 75.000 75.030 69.926 70.000
GFM-7580-50 75.0 80.0 88.0 50.0 2.0 75.060 75.180 80.000 80.030 74.926 75.000
GFM-8085-50 80.0 85.0 93.0 50.0 2.5 85.000 85.035 79.926 80.000
80.060 80.180
GFM-8085-100 80.0 85.0 93.0 100.0 2.5 85.000 85.035 79.926 80.000
GFM-8590-100 85.0 90.0 98.0 100.0 2.5 85.072 85.212 90.000 90.035 84.913 85.000
GFM-9095-100 90.0 95.0 103.0 100.0 2.5 90.072 90.212 95.000 95.035 89.913 90.000
GFM-95100-100 95.0 100.0 108.0 100.0 2.5 95.072 95.212 100.000 100.035 94.913 95.000
GFM-100105-42.5 100.0 105.0 113.0 42.5 2.5 105.000 105.035 99.913 100.000
100.072 100.212
GFM-100105-100 100.0 105.0 113.0 100.0 2.5 105.000 105.035 99.913 100.000
GFM-110115-100 110.0 115.0 123.0 100.0 2.5 110.072 110.212 115.000 115.035 109.913 110.000
GFM-120125-100 120.0 125.0 133.0 100.0 2.5 120.072 120.212 125.000 125.040 119.913 120.000
GFM-125130-100 125.0 130.0 138.0 100.0 2.5 125.085 125.245 130.000 130.040 124.900 125.000
GFM-130135-100 130.0 135.0 143.0 100.0 2.5 130.085 130.245 135.000 135.040 129.900 130.000
GFM-140145-100 140.0 145.0 153.0 100.0 2.5 140.085 140.245 145.000 145.040 139.900 140.000
GFM-150155-40 150.0 155.0 163.0 40.0 2.5 155.000 155.040 149.900 150.000
150.085 150.245
GFM-150155-100 150.0 155.0 163.0 100.0 2.5 155.000 155.040 149.900 150.000
110
d2
d1
Type Dimensions
S
Order key
d2 G T M -04 08- 005
d6
Thickness s (mm)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part Number d1 d2 s d4 d5 h d6
h -0.12 +0.375 +0.2
+0.25 -0.25 -0.05 +0.12
+0.12 +0.125 -0.2
GTM-0509-006 5.0 9.5 0.6 * * 0.3 9.5
GTM-0615-015 6.0 15.0 1.5 * * 1.0 15
GTM-0620-015 6.0 20.0 1.5 13.0 1.5 1.0 20
GTM-0713-005 7.0 13.0 0.5 * * 0.2 13
GTM-0815-005 8.0 15.0 0.5 * * 0.2 15
GTM-0815-015 8.0 15.0 1.5 11.5 * 1.0 15
GTM-0818-010 8.0 18.0 1.0 * * 0.7 18
GTM-0818-015 8.0 18.0 1.5 13.0 1.5 1.0 18
GTM-0918-015 9.0 18.0 1.5 13.5 1.5 1.0 18
GTM-1018-010 10.0 18.0 1.0 * * 0.7 18
GTM-1018-020 10.0 18.0 2.0 * * 1.5 18
GTM-1224-015 12.0 24.0 1.5 18.0 1.5 1.0 24
GTM-1420-015 14.0 20.0 1.5 * * 1.0 20
GTM-1426-015 14.0 26.0 1.5 20.0 2.0 1.0 26
GTM-1522-008 15.0 22.0 0.8 * * 0.5 22
GTM-1524-015 15.0 24.0 1.5 19.5 1.5 1.0 24
GTM-1524-0275 15.0 24.0 2.75 * * 2.0 24
GTM-1630-015 16.0 30.0 1.5 22.0 2.0 1.0 30
GTM-1832-015 18.0 32.0 1.5 25.0 2.0 1.0 32
GTM-2036-015 20.0 36.0 1.5 28.0 3.0 1.0 36
GTM-2238-015 22.0 38.0 1.5 30.0 3.0 1.0 38
GTM-2442-015 24.0 42.0 1.5 33.0 3.0 1.0 42
GTM-2644-015 26.0 44.0 1.5 35.0 3.0 1.0 44
GTM-2835-005 28.0 35.0 0.5 * * 0.2 35
GTM-2848-015 28.0 48.0 1.5 38.0 4.0 1.0 48
GTM-3254-015 32.0 54.0 1.5 43.0 4.0 1.0 54
GTM-3862-015 38.0 62.0 1.5 50.0 4.0 1.0 62
GTM-4266-015 42.0 66.0 1.5 54.0 4.0 1.0 66
GTM-4874-020 48.0 74.0 2.0 61.0 4.0 1.5 74
GTM-5278-020 52.0 78.0 2.0 65.0 4.0 1.5 78
GTM-6290-020 62.0 90.0 2.0 76.0 4.0 1.5 90
GTM-6881-020 68.0 81.0 2.0 * * 1.5 81
2.112
112 Lifetime calculation, configuration and more ➤ www.igus.com/g300
iglide® G300 - Notes iglide®
G300
115
iglide®
J iglide® J - The fast and slow motion specialist
Low friction, low wear
Low wear against different The iglide® J plain bearings are designed for the lowest
shaft materials coefficients of friction while running dry and their low
stick-slip tendency. With a maximum permissible surface
pressure of 5,076 psi iglide® J bearings are not suitable for
extreme loads.
Low coefficients
of friction running dry
Mechanical Properties
Modulus of elasticity psi 348,100 DIN 53457
Tensile strength at 68°F psi 10,590 DIN 53452
Compressive strength psi 8,702
Permissible static surface pressure (68°F) psi 5,076
Shore D-hardness 74 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength
With a maximum permissible surface pressure of 5,075 psi, iglide ® 10
J plain bearings are not suited for extreme loads. The graph shows
7. 5
the elastic deformation of iglide® J for radial loads. At the maximum
permissible load of 5,075 psi, the deformation is less than 2.5%.
Deformation (%)
0
0 1,812 3,625 5,437 7,250
Pressure (psi)
140°F 73°F
14500
Permissible Surface Speeds
The low coefficient of friction and the extremely low stick-slip tendency of
iglide® J plain bearings are especially important at very low speeds. How-
1450
ever, iglide® J material can also be used for high speeds of over 197 fpm.
In both cases,the static friction is very low and stick-slip does not occur.
The maximum values given in the table can only be achieved at the lowest
145
pressure loads. At the given speeds, friction can cause a temperature
increase to maximum permissible levels. In practice, though, this tem-
perature level is rarely reached, due to varying application conditions.
Pressure (psi)
14.5
➤ Surface speed, Page 64
➤ pv value, Page 65
1.45
Continuous Short Term
.197 1.97 19.7 197 1,969 fpm fpm
Surface Speed (fpm)
Rotating 295 590
Permissible pv value for iglide® J running dry against steel shaft,
Oscillating 216 413
at 68°F
Linear 1574 1968
Maximum surface speeds
Temperatures 17,400
iglide ® J plain bearings can be used between -58°F and 194°F; the 14,500
short-term maximum permissible temperature is 248°F. The graph
11,600
shows that the compressive strength of iglide® J plain bearings decreas-
es with increasing temperatures. Also, the wear increases significantly 8,702
above 176°F
Pressure (psi)
5,802
➤ Application Temperatures, Page 67
2,901
0
68 86 104 122 140 158 176 194
iglide® J Application Temperature
Temperature (°F)
Minimum - 58°F
Max. long-term +194°F
Recommended maximum permissible static surface pressure of
Max. short-term +248°F
iglide® J as a result of the temperature
Additional axial securing +140°F
Temperature limits for iglide J ®
0. 4 0.30
0.25
Coef ficient of friction µ
0. 3 0.20
0.15
0. 2 0.10
0.05
0. 1 0.00
9.84 19.69 29.53 39.37 49.22 59.05 68.90 0 725 1450 2175 2900 3625 4350 5075
Surface Speed (fpm ) Pressure (psi)
Coefficient of friction of iglide ® J as a result of the Coefficient of friction of iglide ® J as a result of the
surface speed; p = 108 psi load, v = 1.97 fpm
0.40
0.35
Coef ficient of friction µ
0.30
0.25
iglide® J Coefficient of Friction 0.20
Dry 0.06 - 0.18 0.15
Grease 0.09 0.10
Oil 0.04 4 16 28 40 52 63
Shaft Roughness (rms)
Water 0.04
Coefficients of friction for iglide® J against steel Coefficient of friction of iglide® J as a result of the shaft
(Shaft finish = 40 rms, 50 HRC) surface (1050 hard chromed)
Wear (µm/km)
1.5
in this range. When compared to most iglide® materials, iglide® J has very low wear
1.0
results at low loads with all shaft materials tested.
0.5
Also, for increasing loads up to 725 psi, the wear resistance of iglide® J is excellent.
0.0
Especially suitable is the combination of 303 stainless steel. 0 1 2 3 4 5
In oscillating operation with Cold Rolled Steel and HR Carbon Steel, the wear of
Pressure (psi)
iglide® J is slightly higher than for rotation. For oscillating movements with loads of
290 psi, iglide® J performs best with Cold Rolled Steel shaft. 1050 Steel 304 Stainless
As shown in the graph, the difference in wear between rotation and oscillating HR carbon steel Hard chromed
1.2 3.5
1.0 3.0
Hard anodized aluminum
2.5
0.8
Automatic screw steel
2.0
0.6
HR carbon steel
1.5
304 Stainless
Wear (µm/km)
Wear (µm/km)
0.4
1050 Steel
1.0
0.2
440B
0.5
0.0 0.0
1050 Hard 304 Stainless HR carbon
steel chromed steel steel
Wear of iglide ® J, rotating application with different
shaft materials, p = 108 psi, v = 98 fpm Oscillating Rotating
Wear for oscillating and rotating applications with different
shaft materials under constant load p = 290 psi
Chemical Resistance
iglide® J plain bearings are resistant to diluted lyes and very weak acids, as well as fuels and all types of lubricants. The low moisture absorption
also permits use in wet or damp environments. Plain bearings made of iglide ® J are resistant to common cleaning agents used in the food industry.
The moisture absorption of iglide® J plain bearings is 0.3% in standard atmosphere. The saturation limit in water is 1.3%. These values are so low
that possible design changes due to absorption are only necessary in extreme cases.
➤ Chemical table, Page 1364
Radiation Resistance
Plain bearings made from iglide® J are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® J plain bearings become discolored under UV radiation. However, hardness, compressive strength and the wear resistance of the material
do not change.
Vacuum
When used in a vacuum environment, the iglide® J plain bearings release moisture as a vapor. Therefore, only dehumidified bearings made of iglide®
J are suitable for the vacuum environment.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 119
Inch
*Based on steel housing bore
JFI-0204-02 1/8 1/4 1/8 .360 .047 .2510 .2515 .1241 .1250
.1262 .1280
JFI-0204-06 1/8 1/4 3/8 .360 .047 .2510 .2515 .1241 .1250
JFI-0304-02 3/16 1/4 1/8 .375 .032 .1887 .1905 .2497 .2503 .1858 .1865
JFI-0304-04 3/16 1/4 1/4 .375 .032 .1887 .1905 .2497 .2503 .1858 .1865
JFI-0304-06 3/16 1/4 3/8 .375 .032 .1877 .1905 .2497 .2503 .1858 .1865
JFI-0304-08 3/16 1/4 1/2 .375 .032 .1887 .1905 .2497 .2503 .1858 .1865
JFI-0305-06 3/16 5/16 3/8 .370 .047 .3135 .3140 .1866 .1875
.1887 .1905
JFI-0305-08 3/16 5/16 1/2 .370 .047 .3135 .3140 .1866 .1875
JFI-0405-04 1/4 5/16 1/4 .430 .032 .3122 .3128 .2481 .2490
JFI-0405-06 1/4 5/16 3/8 .430 .032 .2516 .2539 .3122 .3128 .2481 .2490
JFI-0405-12 1/4 5/16 3/4 .430 .032 .3122 .3128 .2481 .2490
JFI-0406-03 1/4 3/8 3/16 .560 .047 .3760 .3765 .2491 .2500
JFI-0406-04 1/4 3/8 1/4 .560 .047 .2516 .2539 .3760 .3765 .2491 .2500
JFI-0406-08 1/4 3/8 1/2 .560 .047 .3760 .3765 .2491 .2500
JFI-0506-04 5/16 3/8 1/4 .500 .032 .3747 .3753 .3106 .3115
JFI-0506-06 5/16 3/8 3/8 .500 .032 .3125 .3148 .3747 .3753 .3106 .3115
JFI-0506-08 5/16 3/8 1/2 .500 .032 .3747 .3753 .3106 .3115
JFI-0507-08 5/16 7/16 1/2 .560 .062 .3141 .3164 .4385 .4390 .3116 .3125
JFI-0607-04 3/8 15/32 1/4 .687 .046 .4684 .4691 .3731 .3740
JFI-0607-06 3/8 15/32 3/8 .687 .046 .3750 .3775 .4684 .4691 .3731 .3740
JFI-0607-08 3/8 15/32 1/2 .687 .046 .4684 .4691 .3731 .3740
JFI-0608-03 3/8 1/2 3/16 .625 .062 .5010 .5015 .3741 .3750
JFI-0608-04 3/8 1/2 1/4 .625 .062 .5010 .5015 .3741 .3750
.3766 .3789
JFI-0608-06 3/8 1/2 3/8 .625 .062 .5010 .5015 .3741 .3750
JFI-0608-08 3/8 1/2 1/2 .625 .062 .5010 .5015 .3741 .3750
JFI-0708-12 7/16 17/32 3/4 .750 .046 .4379 .4406 .5309 .5316 .4366 .4375
JFI-0809-04 1/2 19/32 1/4 .875 .046 .5934 .5941 .4980 .4990
JFI-0809-06 1/2 19/32 3/8 .875 .046 .5000 .5040 .5934 .5941 .4980 .4990
JFI-0809-08 1/2 19/32 1/2 .875 .046 .5934 .5941 .4980 .4990
JFI-0810-04 1/2 5/8 1/4 .875 .062 .6250 .6260 .4990 .5000
JFI-0810-08 1/2 5/8 1/2 .875 .062 .6250 .6260 .4990 .5000
JFI-0810-10 1/2 5/8 5/8 .875 .062 .5020 .5047 .6250 .6260 .4990 .5000
JFI-0810-12 1/2 5/8 3/4 .875 .062 .6250 .6260 .4990 .5000
JFI-0810-16 1/2 5/8 1 .875 .062 .6250 .6260 .4990 .5000
JFI-1011-06 5/8 23/32 3/8 .937 .046 .6253 .6280 .7184 .7192 .6233 .6250
JFI-1011-08 5/8 23/32 1/2 .937 .046 .6253 .6280 .7184 .7192 .6233 .6250
JFI-1011-12 5/8 23/32 3/4 1.000 .046 .6268 .6295 .7184 .7192 .6233 .6250
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 119
Inch
*Based on steel housing bore
JFI-1011-24 5/8 28/32 1 1/2 1.000 .046 .6268 .6295 .7184 .7192 .6233 .6250
JFI-1012-06 5/8 3/4 3/8 1.000 .062 .7500 .7510 .6240 .6250
JFI-1012-08 5/8 3/4 1/2 1.000 .062 .7500 .7510 .6240 .6250
.6270 .6297
JFI-1012-12 5/8 3/4 3/4 1.000 .062 .7500 .7510 .6240 .6250
JFI-1012-16 5/8 3/4 1 1.000 .062 .7500 .7510 .6240 .6250
JFI-1214-08 3/4 7/8 1/2 1.125 .062 .8747 .8755 .7479 .7491
JFI-1214-09 3/4 7/8 9/16 1.125 .062 .8747 .8755 .7479 .7491
JFI-1214-10 3/4 7/8 5/8 1.125 .062 .8747 .8755 .7479 .7491
.7505 .7541
JFI-1214-12 3/4 7/8 3/4 1.125 .062 .8747 .8755 .7479 .7491
JFI-1214-16 3/4 7/8 1 1.125 .062 .8747 .8755 .7479 .7491
JFI-1214-24 3/4 7/8 1 1/2 1.125 .062 .8747 .8755 .7479 .7491
JFI-1216-12 3/4 1 3/4 1.250 .156 1.0000 1.0010 .7490 .7500
.7525 .7559
JFI-1216-16 3/4 1 1 1.250 .156 1.0000 1.0010 .7490 .7500
JFI-1416-12 7/8 1 3/4 1.250 .062 .8757 .8791 .9997 1.0005 .8729 .8741
JFI-141618-11 7/8 1 11/16 1.125 .062 .8774 .8807 .9997 1.0005 .8740 .8750
JFI-1418-24 7/8 1 1/8 1 1/2 1.375 .156 .8775 .8809 1.1250 1.1260 .8740 .8750
JFI-1618-12 1 1 1/8 3/4 1.375 .062 1.1247 1.1255 .9979 .9991
1.0007 1.0041
JFI-1618-16 1 1 1/8 1 1.375 .062 1.1247 1.1255 .9979 .9991
JFI-1620-12 1 1 1/4 3/4 1.500 .188 1.2500 1.2510 .9990 1.0000
JFI-1620-16 1 1 1/4 1 1.500 .188 1.0025 1.0059 1.2500 1.2510 .9990 1.0000
JFI-1620-24 1 1 1/4 1 1/2 1.500 .188 1.2500 1.2510 .9990 1.0000
JFI-1820-08 1 1/8 1 1/2 1/2 1.562 .078 1.1254 1.1288 1.2808 1.2818 1.1226 1.1238
JFI-2024-16 1 1/4 1 1/2 1 1.750 .200 1.4995 1.5005 1.2490 1.2500
1.2531 1.2600
JFI-2024-24 1 1/4 1 1/2 1 1/2 1.750 .200 1.4995 1.5005 1.2490 1.2500
JFI-2428-16 1 1/2 1 3/4 1 2.000 .125 1.7495 1.7505 1.4990 1.5000
1.5032 1.5100
JFI-2428-24 1 1/2 1 3/4 1 1/2 2.000 .125 1.7495 1.7505 1.4990 1.5000
JFI-2630-16 1 5/8 1 7/8 1 2.125 .125 1.6282 1.6350 1.8745 1.8755 1.6240 1.6250
JFI-3236-16 2 2 1/4 1 2.500 .125 2.0032 2.0100 2.2495 2.2505 1.9990 2.0000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
JSM-0104-02 1.5 4.0 2.0 1.514 1.554 4.000 4.012 1.475 1.500
JSM-0203-07 2.0 3.5 7.0 3.000 3.012 1.975 2.000
2.014 2.054
JSM-0205-02 2.0 5.0 2.5 5.000 5.012 1.975 2.000
JSM-0206-02 2.5 6.0 2.5 6.000 6.012 1.975 2.000
2.514 2.554
JSM-0206-03 2.5 6.0 3.5 6.000 6.012 1.975 2.000
JSM-0304-05 3.0 4.5 5.0 4.500 4.512 2.975 3.000
3.014 3.054
JSM-0304-09 3.0 4.5 9.0 4.500 4.512 2.975 3.000
JSM-0305-03 3.0 5.0 3.0 5.000 5.012 2.975 3.000
3.020 3.080
JSM-0305-04 3.0 5.0 4.0 5.000 5.012 2.975 3.000
JSM-0308-04 3.0 8.0 4.0 8.000 8.015 2.975 3.000
3.020 3.080
JSM-0308-05 3.0 8.0 5.0 8.000 8.015 2.975 3.000
JSM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
JSM-0405-06 4.0 5.5 6.0 4.020 4.068 5.500 5.512 3.970 4.000
JSM-0405-08 4.0 5.5 8.0 5.500 5.512 3.970 4.000
JSM-0507-046 5.0 7.0 4.6 7.000 7.015 4.970 5.000
JSM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
5.020 5.068
JSM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
JSM-0507-15 5.0 7.0 15.0 7.000 7.015 4.970 5.000
JSM-0508-05 5.0 7.0 15.0 5.030 5.105 7.000 7.01 4.970 5.000
JSM-0607-08 6.0 7.0 8.0 7.000 7.015 5.970 6.000
JSM-0607-12.5 6.0 7.0 12.5 6.020 6.068 7.000 7.015 5.970 6.000
JSM-0607-14 6.0 7.0 14.0 7.000 7.015 5.970 6.000
JSM-0608-043 6.0 8.0 4.3 6.020 6.058 8.000 8.015 5.970 6.000
JSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
JSM-0608-08 6.0 8.0 8.0 6.020 6.068 8.000 8.015 5.970 6.000
JSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
JSM-0609-06 6.0 9.0 6.0 6.020 6.068 9.000 9.015 5.970 6.000
JSM-0610-10 6.0 10.0 10.0 6.020 6.068 10.000 10.015 5.970 6.000
JSM-0709-09 7.0 9.0 9.0 7.025 7.083 9.000 9.015 6.964 7.000
JSM-0810-04 8.0 10.0 4.0 10.000 10.015 7.964 8.000
JSM-0810-06 8.0 10.0 6.0 10.000 10.015 7.964 8.000
JSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
8.025 8.083
JSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
JSM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
JSM-0810-16 8.0 10.0 16.0 10.000 10.015 7.964 8.000
JSM-0812-10 8.0 12.0 10.0 12.000 12.018 7.964 8.000
8.040 8.130
JSM-0812-12 8.0 12.0 12.0 12.000 12.018 7.964 8.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
JSM-0911-06 9.0 11.0 10.0 9.025 9.083 11.000 11.018 8.964 9.000
JSM-1012-05 10.0 12.0 5.0 12.000 12.018 9.964 10.000
JSM-1012-06 10.0 12.0 6.0 12.000 12.018 9.964 10.000
JSM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
JSM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
10.025 10.083
JSM-1012-11 10.0 12.0 11.0 12.000 12.018 9.964 10.000
JSM-1012-12 10.0 12.0 12.0 12.000 12.018 9.964 10.000
JSM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
JSM-1012-20 10.0 12.0 20.0 12.000 12.018 9.964 10.000
JSM-1014-10 10.0 14.0 10.0 14.000 14.018 9.964 10.000
10.040 10.130
JSM-1014-16 10.0 14.0 16.0 14.000 14.018 9.964 10.000
JSM-1214-06 12.0 14.0 6.0 14.000 14.018 11.957 12.000
JSM-1214-08 12.0 14.0 8.0 14.000 14.018 11.957 12.000
JSM-1214-09 12.0 14.0 9.0 14.000 14.018 11.957 12.000
JSM-1214-10 12.0 14.0 10.0 12.032 12.102 14.000 14.018 11.957 12.000
JSM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
JSM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
JSM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
JSM-1216-12 12.0 16.0 12.0 16.000 16.018 11.957 12.000
12.050 12.160
JSM-1216-17 12.0 16.0 17.0 16.000 16.018 11.957 12.000
JSM-1315-10 13.0 15.0 10.0 15.000 15.018 12.957 13.000
13.032 13.102
JSM-1315-20 13.0 15.0 20.0 15.000 15.018 12.957 13.000
JSM-1416-05 14.0 16.0 5.0 16.000 16.018 13.957 14.000
JSM-1416-08 14.0 16.0 8.0 16.000 16.018 13.957 14.000
JSM-1416-10 14.0 16.0 10.0 16.000 16.018 13.957 14.000
JSM-1416-15 14.0 16.0 15.0 14.032 14.102 16.000 16.018 13.957 14.000
JSM-1416-20 14.0 16.0 20.0 16.000 16.018 13.957 14.000
JSM-1416-25 14.0 16.0 25.0 16.000 16.018 13.957 14.000
JSM-1416-33 14.0 16.0 33.0 16.000 16.018 13.957 14.000
JSM-1418-18 14.0 18.0 18.0 18.000 18.018 13.957 14.000
14.032 14.102
JSM-1420-20 14.0 20.0 20.0 20.000 20.018 13.957 14.000
JSM-1517-12 15.0 17.0 12.0 17.000 17.018 14.957 15.000
JSM-1517-15 15.0 17.0 150 17.000 17.018 14.957 15.000
15.032 15.102
JSM-1517-20 15.0 17.0 20.0 17.000 17.018 14.957 15.000
JSM-1517-25 15.0 17.0 25.0 17.000 17.018 14.957 15.000
JSM-1618-10 16.0 18.0 10.0 18.000 18.018 15.957 16.000
16.032 16.102
JSM-1618-12 16.0 18.0 12.0 18.000 18.018 15.957 16.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
JSM-6065-60 60.0 65.0 60.0 60.060 60.180 65.000 65.030 59.926 60.000
JSM-6570-50 65.0 70.0 50.0 65.060 65.180 70.000 70.030 64.926 65.000
JSM-7075-60 70.0 75.0 60.0 70.060 70.180 75.000 75.030 69.926 70.000
JSM-7580-60 75.0 80.0 60.0 75.060 75.180 80.000 80.030 74.926 75.000
JSM-8085-100 80.0 85.0 100.0 80.060 80.180 85.000 85.035 79.926 80.000
JSM-8086-60 80.0 86.0 60.0 80.060 80.180 86.000 85.035 79.926 80.000
JSM-8590-100 85.0 90.0 100.0 85.072 85.212 90.000 90.035 84.913 85.000
JSM-100105-100 110.0 105.0 100.0 100.072 100.212 105.000 105.035 99.913 100.000
JSM-110115-60 110.0 115.0 60.0 110.072 110.212 110.000 110.035 109.913 100.000
30°
J F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 119
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
JFM-0304-03 3.0 4.5 7.5 3.0 0.75 4.500 4.512 2.975 3.000
JFM-0304-045 3.0 4.5 7.5 4.5 0.75 3.014 3.054 4.500 4.512 2.975 3.000
JFM-0304-05 3.0 4.5 7.5 5.0 0.75 4.500 4.512 2.975 3.000
JFM-0306-10 3.0 6.0 9.0 10.0 1.5 3.020 3.068 4.500 4.512 2.975 3.000
JFM-0405-03 4.0 5.5 9.5 3.0 0.75 5.500 5.512 3.970 4.000
4.020 4.068
JFM-0405-06 4.0 5.5 9.5 6.0 0.75 5.500 5.512 3.970 4.000
JFM-0408-04 4.0 8.0 12.0 4.0 2.0 4.030 4.105 8.000 8.015 3.970 4.000
JFM-0506-05 5.0 6.0 10.0 5.0 0.5 5.020 5.068 6.000 6.015 4.970 5.000
JFM-0507-03 5.0 7.0 11.0 3.0 1.0 7.000 7.015 4.970 5.000
5.020 5.068
JFM-0507-05 5.0 7.0 11.0 5.0 1.0 7.000 7.015 4.970 5.000
JFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
JFM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
6.020 6.068
JFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
JFM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
JFM-0610-10 6.0 10.0 14.0 10.0 2.0 6.030 6.105 10.000 10.015 5.970 6.000
JFM-0810-038 8.0 10.0 15.0 3.8 1.0 10.000 10.015 7.964 8.000
JFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
JFM-0810-06 8.0 10.0 15.0 6.0 1.0 10.000 10.015 7.964 8.000
JFM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
JFM-0810-08 8.0 10.0 15.0 8.0 1.0 10.000 10.015 7.964 8.000
8.025 8.083
JFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
JFM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
JFM-0810125-10 8.0 10.0 12.5 10.0 1.0 10.000 10.015 7.964 8.000
JFM-081014-10 8.0 10.0 14.0 10.0 1.0 10.000 10.015 7.964 8.000
JFM-081016-11 8.0 10.0 16.0 11.0 1.0 10.000 10.015 7.964 8.000
JFM-0812-05 8.0 12.0 16.0 5.0 2.0 12.000 12.018 7.964 8.000
JFM-0812-06 8.0 12.0 16.0 6.0 2.0 12.000 12.018 7.964 8.000
8.040 8.130
JFM-0812-12 8.0 12.0 16.0 12.0 2.0 12.000 12.018 7.964 8.000
JFM-0812-30 8.0 12.0 16.0 30.0 2.0 12.000 12.018 7.964 8.000
JFM-101215-035 10.0 12.0 15.0 3.5 1.0 12.000 12.018 9.964 10.000
JFM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
JFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
JFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
10.025 10.083
JFM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
JFM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
JFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
JFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 119
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
JFM-1012-18 10.0 12.0 18.0 18.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
JFM-1014-14 10.0 14.0 17.5 14.0 1.0 14.000 14.018 9.964 10.000
10.025 10.083
JFM-101420-12 10.0 14.0 20.0 12.0 2.0 14.000 14.018 9.964 10.000
JFM-1016-10 10.0 16.0 22.0 10.0 3.0 16.000 16.018 9.964 10.000
10.040 10.130
JFM-1016-16 10.0 16.0 22.0 16.0 3.0 16.000 16.018 9.964 10.000
JFM-1113-05 11.0 13.0 18.0 5.0 1.0 11.032 11.102 13.000 13.018 10.964 11.000
JFM-1214-05 12.0 14.0 20.0 5.0 1.0 14.000 14.018 11.957 12.000
JFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
JFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
JFM-121418-10 12.0 14.0 18.0 10.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
JFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
JFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
JFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
JFM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
JFM-1218-08 12.0 18.0 24.0 8.0 3.0 18.000 18.018 11.957 12.000
JFM-1218-12 12.0 18.0 24.0 12.0 3.0 12.050 12.160 18.000 18.018 11.957 12.000
JFM-1218-20 12.0 18.0 22.0 20.0 3.0 18.000 18.018 11.957 12.000
JFM-1416-03 14.0 16.0 22.0 3.0 1.0 16.000 16.018 13.957 14.000
JFM-1416-10 14.0 16.0 22.0 10.0 1.0 16.000 16.018 13.957 14.000
JFM-1416-12 14.0 16.0 22.0 12.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
JFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
JFM-141822-20 14.0 18.0 22.0 20.0 2.0 18.000 18.018 13.957 14.000
JFM-1420-20 14.0 20.0 25.0 20.0 3.0 14.050 14.160 20.000 20.021 13.957 14.000
JFM-1517-04 15.0 17.0 23.0 4.0 1.0 17.000 17.018 14.957 15.000
JFM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
15.032 15.102
JFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
JFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
JFM-1521-20 15.0 21.0 27.0 20.0 3.0 15.050 15.160 21.000 21.021 14.957 15.000
JFM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.032 16.102
JFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
JFM-1622-12 16.0 22.0 28.0 12.0 3.0 22.000 22.021 15.957 16.000
JFM-1622-15 16.0 22.0 28.0 15.0 3.0 22.000 22.021 15.957 16.000
16.050 16.160
JFM-1622-20 16.0 22.0 28.0 20.0 3.0 22.000 22.021 15.957 16.000
JFM-1622-25 16.0 22.0 28.0 25.0 3.0 22.000 22.021 15.957 16.000
JFM-1719-09 17.0 19.0 25.0 9.0 1.0 19.000 19.018 16.957 17.000
17.032 17.102
JFM-1719-21 17.0 19.0 25.0 21.0 1.0 19.000 19.018 16.957 17.000
JFM-1820-04 18.0 20.0 26.0 4.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
30°
J F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 119
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
JFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
JFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
JFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
JFM-1821-12 18.0 21.0 25.0 12.0 1.0 18.032 18.102 21.000 21.021 17.957 18.000
JFM-1922-36 19.0 22.0 26.0 36.0 1.0 19.040 19.124 22.000 22.021 18.957 19.000
JFM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
JFM-2023-15.5 20.0 23.0 30.0 15.5 1.5 23.000 23.021 19.948 20.000
20.040 20.124
JFM-2023-16 20.0 23.0 30.0 16.5 1.5 23.000 23.021 19.948 20.000
JFM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
JFM-202530-15 20.0 25.0 30.0 15.0 2.5 20.065 20.195 25.000 25.021 19.948 20.000
JFM-2026-15 20.0 26.0 32.0 15.0 3.0 26.000 26.021 19.948 20.000
JFM-2026-20 20.0 26.0 32.0 20.0 3.0 26.000 26.021 19.948 20.000
20.065 20.195
JFM-2026-25 20.0 26.0 32.0 25.0 3.0 26.000 26.021 19.948 20.000
JFM-2026-30 20.0 26.0 32.0 30.0 3.0 26.000 26.021 19.948 20.000
JFM-222532-08 22.0 25.0 32.0 8.0 1.5 22.040 22.124 25.000 25.021 21.948 22.000
JFM-2430-30 24.0 30.0 36.0 30.0 3.0 24.040 24.124 30.000 30.021 23.948 24.000
JFM-2528-06 25.0 28.0 35.0 6.0 1.5 28.000 28.021 24.948 25.000
JFM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
JFM-2528-14.5 25.0 28.0 35.0 14.5 1.5 28.000 28.021 24.948 25.000
25.040 25.124
JFM-2528-16 25.0 28.0 35.0 16.5 1.5 28.000 28.021 24.948 25.000
JFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
JFM-252839-075 25.0 28.0 39.0 7.5 1.5 28.000 28.021 24.948 25.000
JFM-2532-20 25.0 32.0 38.0 20.0 4.0 32.000 32.021 24.948 25.000
JFM-2532-25 25.0 32.0 38.0 25.0 4.0 25.065 25.195 32.000 32.021 24.948 25.000
JFM-2532-40 25.0 32.0 38.0 40.0 2.0 32.000 32.021 24.948 25.000
JFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
JFM-3034-20 30.0 34.0 42.0 20.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
JFM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
JFM-3038-20 30.0 38.0 44.0 20.0 4.0 38.000 38.025 29.948 30.000
JFM-3038-30 30.0 38.0 44.0 30.0 4.0 30.065 30.195 38.000 38.025 29.948 30.000
JFM-3038-36 30.0 38.0 44.0 36.0 4.0 38.000 38.025 29.948 30.000
JFM-3539-12 35.0 39.0 47.0 12.0 2.0 39.000 39.025 34.938 35.000
JFM-3539-16 35.0 39.0 47.0 16.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
JFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
JFM-4044-20 40.0 44.0 52.0 20.0 2.0 44.000 44.025 39.938 40.000
JFM-4044-30 40.0 44.0 52.0 30.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
JFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 119
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
JFM-4550-20 45.0 50.0 58.0 20.0 2.0 50.000 50.025 44.938 45.000
45.050 45.150
JFM-4550-50 45.0 50.0 58.0 50.0 2.0 50.000 50.025 44.938 45.000
JFM-5055-50 50.0 55.0 63.0 50.0 2.0 50.050 50.150 55.000 55.030 49.938 50.000
JFM-556082-30 55.0 60.0 82.0 30.0 2.0 60.000 60.030 54.926 55.000
55.060 55.180
JFM-5560-50 55.0 60.0 68.0 50.0 2.0 60.000 60.030 54.926 55.000
JFM-6065-50 60.0 65.0 73.0 50.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
JFM-7075-50 70.0 75.0 83.0 50.0 2.0 70.060 70.180 75.000 75.030 69.926 70.000
JFM-9095-100 90.0 95.0 108.0 100.0 2.5 90.072 90.212 95.000 95.035 89.900 90.000
JFM-100105-100 100.0 115.0 123.0 100.0 2.5 110.072 110.212 115.000 115.035 109.900 110.000
iglide®
J iglide® J - Product range
Thrust washer - Metric d4
d5
d1
Type Dimensions
S
Order key
d2 J T M -04 08- 005
d6
Thickness s (mm)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part Number d1 d2 s d4 d5 h d6
h
-0.12 +0.375 +0.2
0.3 -0.3 -0.05 +0.12
+0.12 +0.125 0.2
135
iglide®
M250 iglide® M250 - Thick and Tough
Excellent vibration dampening
Mechanical Properties
Modulus of elasticity psi 391,600 DIN 53457
Tensile strength at 68°F psi 16,240 DIN 53452
Compressive strength psi 7,542
Permissible static surface pressure (68°F) psi 2,901
Shore D-hardness 79 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength
4
14,500
Permissible Surface Speeds
Permissible pv value for iglide® M250 running dry against a steel Linear 492 984
shaft, at 68°F Maximum surface speeds
Temperatures
7,252
Pressure (psi)
1,450
➤ Applications Temperatures, Page 67
0
68 86 104 122 140 158 176
0.7 0.6
0.5
0.6
C oef ficient of friction µ
Coefficient of friction µ
0.4
0.5
0.3
0.4
0.2
0.3 0.1
0.2 0.0
1.97 19.69 29.53 39.37 49.22 59.05 68.90 0 290 580 870 1160 1450 1740 2030 2320 2610 2900
Coefficient of friction of iglide® M250 as a result of the Coefficient of friction of iglide® M250 as a result of the
surface speed; p = 108 psi pressure, v = 1.97 fpm
0.60
0.55
0.50
Coefficient of friction µ
0.45
iglide® M250 Coefficient of Friction
0.40
Dry 0.18 - 0.40
0.35
Grease 0.09
0.30
Oil 0.04 4 16 28 40 52 63
Water 0.04 Shaft Roughness (rms)
Wear (µm/km)
6.0
smaller loads.
4.0
If the load increases, the wear of a bearing clearly increases. Therefore, a suitable shaft
2.0
material must be considered for higher loads. These are hardened shafts, such as, for
0.0
example, Cold Rolled Steel or hard-chromed shafts. 0.0 145 290 435 580 725
The graph makes it clear that iglide® M250 is considerably better for rotational than Pressure (psi)
for oscillating operation. However, it must be mentioned that in oscillating movements, 1050 Steel 304 Stainless
often the vibrations that act on the bearings are especially high. Here, iglide® M250 HR carbon steel Hard chromed
can utilize its special dampening properties. In our test, these vibrations are excluded
so that the comparison between rotation and oscillating operation is captured first. Wear of iglide® M250 with different shaft materials in
rotational operation
➤ Shaft Materials, Page 71
30
6
25
5
20
Hard anodized aluminum
4
15
1050, hard chromed
Wear (µm/km)
3 10
304 Stainless
Carbon Steel
Wear (µm/km)
1050 Steel
2 5
0
1 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
0
Oscillating Rotating
Wear for iglide® M250, rotating with different shaft materials, p Wear for oscillating and rotating applications with
= 108 psi, v=98 fpm different shaft materials at p = 290 psi
Medium Resistance
Radiation Resistance
Plain bearings made from iglide® M250 can be used conditionally under radioactive radiation. They are resistant to radiation up to a radiation
intensity of 1000 Gy.
Vacuum
In a vacuum environment, the iglide® M250 plain bearing releases moisture as vapor. The relatively high moisture absorption of the bearing allows
only limited use in the vacuum.
UV Resistance
iglide® M250 plain bearings are permanently resistant to UV radiation.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
MSI-0507-12 5/16 7/16 3/4 .3164 .3141 .4390 .4385 .3125 .3116
MSI-0607-04 3/8 7/16 1/4 .4390 .4385 .3750 .3741
MSI-0607-06 3/8 7/16 3/8 .3789 .3766 .4390 .4385 .3750 .3741
MSI-0607-08 3/8 7/16 1/2 .4390 .4385 .3750 .3741
MSI-0608-03 3/8 1/2 3/16 .5015 .5010 .3750 .3741
MSI-0608-04 3/8 1/2 1/4 .5015 .5010 .3750 .3741
MSI-0608-05 3/8 1/2 5/16 .5015 .5010 .3750 .3741
MSI-0608-06 3/8 1/2 3/8 .5015 .5010 .3750 .3741
.3789 .3766
MSI-0608-08 3/8 1/2 1/2 .5015 .5010 .3750 .3741
MSI-0608-10 3/8 1/2 5/8 .5015 .5010 .3750 .3741
MSI-0608-12 3/8 1/2 3/4 .5015 .5010 .3750 .3741
MSI-0608-16 3/8 1/2 1 .5015 .5010 .3750 .3741
MSI-0709-06 7/16 9/16 3/8 .5635 .5625 .4375 .4365
.4422 .4395
MSI-0709-08 7/16 9/16 1/2 .5635 .5625 .4375 .4365
MSI-0810-04 1/2 5/8 1/4 .6260 .6250 .5000 .4990
MSI-0810-05 1/2 5/8 5/16 .6260 .6250 .5000 .4990
MSI-0810-06 1/2 5/8 3/8 .6260 .6250 .5000 .4990
MSI-0810-08 1/2 5/8 1/2 .5047 .5020 .6260 .6250 .5000 .4990
MSI-0810-10 1/2 5/8 5/8 .6260 .6250 .5000 .4990
MSI-0810-12 1/2 5/8 3/4 .6260 .6250 .5000 .4990
MSI-0810-16 1/2 5/8 1 .6260 .6250 .5000 .4990
MSI-1012-04 5/8 3/4 1/4 .7510 .7500 .6250 .6240
MSI-1012-06 5/8 3/4 3/8 .7510 .7500 .6250 .6240
MSI-1012-08 5/8 3/4 1/2 .7510 .7500 .6250 .6240
MSI-1012-10 5/8 3/4 5/8 .6297 .6270 .7510 .7500 .6250 .6240
MSI-1012-12 5/8 3/4 3/4 .7510 .7500 .6250 .6240
MSI-1012-16 5/8 3/4 1 .7510 .7500 .6250 .6240
MSI-1012-26 5/8 3/4 1 5/8 .7510 .7500 .6250 .6240
MSI-1013-06 5/8 13/16 3/8 .8135 .8125 .6250 .6240
MSI-1013-08 5/8 13/16 1/2 .8135 .8125 .6250 .6240
MSI-1013-10 5/8 13/16 5/8 .6297 .6270 .8135 .8125 .6250 .6240
MSI-1013-12 5/8 13/16 3/4 .8135 .8125 .6250 .6240
MSI-1013-16 5/8 13/16 1 .8135 .8125 .6250 .6240
MSI-1113-12 11/16 13/16 3/4 .8135 .8125 .6875 .6865
MSI-1113-14 11/16 13/16 7/8 .6921 .6894 .8135 .8125 .6875 .6865
MSI-1113-16 11/16 13/16 1 .8135 .8125 .6875 .6865
MSI-1214-05 3/4 7/8 5/16 .7559 .7525 .8760 .8750 .7500 .7490
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 139
Inch
*Based on steel housing bore
MFI-0203-02 1/8 3/16 1/8 .3125 .032 .1885 .1880 .1250 .1241
.1280 .1262
MFI-0203-04 1/8 3/16 1/4 .3125 .032 .1885 .1880 .1250 .1241
MFI-0204-02 1/8 1/4 1/8 .360 .047 .2515 .2510 .1250 .1241
MFI-0204-03 1/8 1/4 3/16 .360 .047 .2515 .2510 .1250 .1241
MFI-0204-04 1/8 1/4 1/4 .360 .047 .1280 .1262 .2515 .2510 .1250 .1241
MFI-0204-06 1/8 1/4 3/8 .360 .047 .2515 .2510 .1250 .1241
MFI-0204-12 1/8 1/4 3/4 .360 .047 .2515 .2510 .1250 .1241
MFI-0304-04 3/16 1/4 1/4 .375 .032 .2515 .2510 .1875 .1866
MFI-0304-06 3/16 1/4 3/8 .375 .032 .1905 .1887 .2515 .2510 .1875 .1866
MFI-0304-08 3/16 1/4 1/2 .375 .032 .2515 .2510 .1875 .1866
MFI-0305-03 3/16 5/16 3/16 .370 .047 .3140 .3135 .1875 .1866
MFI-0305-04 3/16 5/16 1/4 .370 .047 .3140 .3135 .1875 .1866
MFI-0305-05 3/16 5/16 5/16 .370 .047 .1905 .1887 .3140 .3135 .1875 .1866
MFI-0305-06 3/16 5/16 3/8 .370 .047 .3140 .3135 .1875 .1866
MFI-0305-08 3/16 5/16 1/2 .370 .047 .3140 .3135 .1875 .1866
MFI-0405-02 1/4 5/16 1/8 .4375 .032 .3140 .3135 .2500 .2491
MFI-0405-03 1/4 5/16 3/16 .4375 .032 .3140 .3135 .2500 .2491
MFI-0405-04 1/4 5/16 1/4 .4375 .032 .3140 .3135 .2500 .2491
MFI-0405-06 1/4 5/16 3/8 .4375 .032 .2539 .2516 .3140 .3135 .2500 .2491
MFI-0405-07 1/4 5/16 7/16 .4375 .032 .3140 .3135 .2500 .2491
MFI-0405-08 1/4 5/16 1/2 .4375 .032 .3140 .3135 .2500 .2491
MFI-0405-12 1/4 5/16 3/4 .4375 .032 .3140 .3135 .2500 .2491
MFI-0406-02 1/4 3/8 1/8 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-03 1/4 3/8 3/16 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-04 1/4 3/8 1/4 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-05 1/4 3/8 5/16 .560 .047 .3765 .3760 .2500 .2491
.2539 .2516
MFI-0406-06 1/4 3/8 3/8 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-08 1/4 3/8 1/2 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-10 1/4 3/8 5/8 .560 .047 .3765 .3760 .2500 .2491
MFI-0406-12 1/4 3/8 3/4 .560 .047 .3765 .3760 .2500 .2491
MFI-0506-02 5/16 3/8 1/8 .500 .032 .3765 .3760 .3125 .3116
MFI-0506-04 5/16 3/8 1/4 .500 .032 .3765 .3760 .3125 .3116
MFI-0506-06 5/16 3/8 3/8 .500 .032 .3164 .3141 .3765 .3760 .3125 .3116
MFI-0506-08 5/16 3/8 1/2 .500 .032 .3765 .3760 .3125 .3116
MFI-0506-15 5/16 3/8 15/16 .500 .062 .3765 .3760 .3125 .3116
MFI-0507-03 5/16 7/16 3/16 .560 .062 .4390 .4385 .3125 .3116
.3164 .3141
MFI-0507-04 5/16 7/16 1/4 .560 .062 .4390 .4385 .3125 .3116
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 139
Inch
*Based on steel housing bore
MFI-0507-05 5/16 7/16 5/16 .560 .062 .4390 .4385 .3125 .3116
MFI-0507-06 5/16 7/16 3/8 .560 .062 .4390 .4385 .3125 .3116
MFI-0507-08 5/16 7/16 1/2 .560 .062 .3164 .3141 .4390 .4385 .3125 .3116
MFI-0507-10 5/16 7/16 5/8 .560 .062 .4390 .4385 .3125 .3116
MFI-0507-12 5/16 7/16 3/4 .560 .062 .4390 .4385 .3125 .3116
MFI-0607-04 3/8 7/16 1/4 .5625 .032 .4390 .4385 .3750 .3741
MFI-0607-06 3/8 7/16 3/8 .5625 .032 .3789 .3766 .4390 .4385 .3750 .3741
MFI-0607-08 3/8 7/16 1/2 .5625 .032 .4390 .4385 .3750 .3741
MFI-0608-02 3/8 1/2 1/8 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-03 3/8 1/2 3/16 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-04 3/8 1/2 1/4 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-05 3/8 1/2 5/16 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-06 3/8 1/2 3/8 .625 .062 .5015 .5010 .3750 .3741
.3789 .3766
MFI-0608-08 3/8 1/2 1/2 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-10 3/8 1/2 5/8 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-12 3/8 1/2 3/4 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-16 3/8 1/2 1 .625 .062 .5015 .5010 .3750 .3741
MFI-0608-17.5 3/8 1/2 1 3/32 .625 .062 .5015 .5010 .3750 .3741
MFI-0709-06 7/16 9/16 3/8 .687 .062 .5635 .5625 .4375 .4365
MFI-0709-07 7/16 9/16 7/16 .687 .062 .4422 .4395 .5635 .5625 .4375 .4365
MFI-0709-08 7/16 9/16 1/2 .687 .062 .5635 .5625 .4375 .4365
MFI-0810-02 1/2 5/8 1/8 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-04 1/2 5/8 1/4 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-05 1/2 5/8 5/16 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-06 1/2 5/8 3/8 .875 .062 .6260 .6250 .5000 .4990
.5047 .5020
MFI-0810-08 1/2 5/8 1/2 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-10 1/2 5/8 5/8 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-12 1/2 5/8 3/4 .875 .062 .6260 .6250 .5000 .4990
MFI-0810-16 1/2 5/8 1 .875 .062 .6260 .6250 .5000 .4990
MFI-1012-06 5/8 3/4 3/8 1.000 .062 .7510 .7500 .6250 .6240
MFI-1012-08 5/8 3/4 1/2 1.000 .062 .7510 .7500 .6250 .6240
MFI-1012-10 5/8 3/4 5/8 1.000 .062 .7510 .7500 .6250 .6240
.6297 .6270
MFI-1012-12 5/8 3/4 3/4 1.000 .062 .7510 .7500 .6250 .6240
MFI-1012-16 5/8 3/4 1 1.000 .062 .7510 .7500 .6250 .6240
MFI-1012-24 5/8 3/4 1 1/2 1.000 .062 .7510 .7500 .6250 .6240
MFI-1013-08 5/8 13/16 1/2 1.063 .156 .8135 .8125 .6250 .6240
.6297 .6270
MFI-1013-10 5/8 13/16 5/8 1.063 .156 .8135 .8125 .6250 .6240
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 139
Inch
*Based on steel housing bore
MFI-1013-12 5/8 13/16 3/4 1.063 .156 .8135 .8125 .6250 .6240
.6297 .6270
MFI-1013-16 5/8 13/16 1 1.063 .156 .8135 .8125 .6250 .6240
MFI-1214-06 3/4 7/8 3/8 1.125 .062 .8760 .8750 .7500 .7490
MFI-1214-08 3/4 7/8 1/2 1.125 .062 .8760 .8750 .7500 .7490
MFI-1214-12 3/4 7/8 3/4 1.125 .062 .7559 .7525 .8760 .8750 .7500 .7490
MFI-1214-16 3/4 7/8 1 1.125 .062 .8760 .8750 .7500 .7490
MFI-1214-24 3/4 7/8 1 1/2 1.125 .062 .8760 .8750 .7500 .7490
MFI-1216-08 3/4 1 1/2 1.250 .156 1.0010 1.0000 .7500 .7490
MFI-1216-10 3/4 1 5/8 1.250 .156 1.0010 1.0000 .7500 .7490
MFI-1216-12 3/4 1 3/4 1.250 .156 1.0010 1.0000 .7500 .7490
.7559 .7525
MFI-1216-16 3/4 1 1 1.250 .156 1.0010 1.0000 .7500 .7490
MFI-1216-24 3/4 1 1 1/2 1.250 .156 1.0010 1.0000 .7500 .7490
MFI-1216-32 3/4 1 2 1.250 .156 1.0010 1.0000 .7500 .7490
MFI-1416-12 7/8 1 3/4 1.250 .062 1.0010 1.0000 .8750 .8740
MFI-1416-16 7/8 1 1 1.250 .062 .8809 .8775 1.0010 1.0000 .8750 .8740
MFI-1416-24 7/8 1 1 1/2 1.250 .062 1.0010 1.0000 .8750 .8740
MFI-1418-08 7/8 1 1/8 1/2 1.375 .156 1.1260 1.1250 .8750 .8740
MFI-1418-12 7/8 1 1/8 3/4 1.375 .156 1.1260 1.1250 .8750 .8740
.8809 .8775
MFI-1418-16 7/8 1 1/8 1 1.375 .156 1.1260 1.1250 .8750 .8740
MFI-1418-24 7/8 1 1/8 1 1/2 1.375 .156 1.1260 1.1250 .8750 .8740
MFI-1618-03 1 1 1/8 3/16 1.375 .062 1.1260 1.1250 1.0000 .9990
MFI-1618-12 1 1 1/8 3/4 1.375 .062 1.1260 1.1250 1.0000 .9990
1.0059 1.0025
MFI-1618-16 1 1 1/8 1 1.375 .062 1.1260 1.1250 1.0000 .9990
MFI-1618-24 1 1 1/8 1 1/2 1.375 .062 1.1260 1.1250 1.0000 .9990
MFI-1620-08 1 1 1/4 1/2 1.500 .188 1.2510 1.2500 1.0000 .9990
MFI-1620-10 1 1 1/4 5/8 1.500 .188 1.2510 1.2500 1.0000 .9990
MFI-1620-12 1 1 1/4 3/4 1.500 .188 1.0059 1.0025 1.2510 1.2500 1.0000 .9990
MFI-1620-16 1 1 1/4 1 1.500 .188 1.2510 1.2500 1.0000 .9990
MFI-1620-24 1 1 1/4 1 1/2 1.500 .188 1.2510 1.2500 1.0000 .9990
MFI-2024-07 1 1/4 1 1/2 7/16 1.750 .200 1.5005 1.4995 1.2500 1.2490
MFI-2024-12 1 1/4 1 1/2 3/4 1.750 .200 1.5005 1.4995 1.2500 1.2490
1.2600 1.2531
MFI-2024-16 1 1/4 1 1/2 1 1.750 .200 1.5005 1.4995 1.2500 1.2490
MFI-2024-24 1 1/4 1 1/2 1 1/2 1.750 .200 1.5005 1.4995 1.2500 1.2490
MFI-2226-12 1 3/8 1 5/8 3/4 1.875 .125 1.6255 1.6245 1.3750 1.3740
1.3781 1.3759
MFI-2226-16 1 3/8 1 5/8 1 1.875 .125 1.6255 1.6245 1.3750 1.3740
MFI-2428-12 1 1/2 1 3/4 3/4 2.000 .125 1.7505 1.7495 1.5000 1.4990
1.5100 1.5032
MFI-2428-16 1 1/2 1 3/4 1 2.000 .125 1.7505 1.7495 1.5000 1.4990
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 139
Inch
*Based on steel housing bore
MFI-2428-24 1 1/2 1 3/4 1 1/2 2.000 .125 1.5100 1.5032 1.7505 1.7495 1.5000 1.4990
MFI-2630-16 1 5/8 1 7/8 1 2.125 .125 1.6350 1.6282 1.8755 1.8745 1.6250 1.6240
MFI-2832-12 1 3/4 2 3/4 2.250 .125 2.0005 1.9995 1.7500 1.7490
MFI-2832-16 1 3/4 2 1 2.250 .125 1.7595 1.7531 2.0005 1.9995 1.7500 1.7490
MFI-2832-24 1 3/4 2 1 1/2 2.250 .125 2.0005 1.9995 1.7500 1.7490
MFI-3236-16 2 2 1/4 1 2.500 .125 2.2512 2.2500 2.0000 1.9990
MFI-3236-24 2 2 1/4 1 1/2 2.500 .125 2.0100 2.0032 2.2512 2.2500 2.0000 1.9990
MFI-3236-32 2 2 1/4 2 2.500 .125 2.2512 2.2500 2.0000 1.9990
d1
Type Dimensions
S
Order key
d2 M T I - 04
d6
Inner-Ø d1 (inch)
Form T (washer)
iglide® material
h
d5
d4
Inch
d6
Part Number d1(nominal) d1 d2 s
h
Max. Min. Max. Min. -0.0056
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
MSM-0103-02 1.0 3.0 2.0 1.020 1.080 3.000 3.080 .975 1.000
MSM-0104-02 1.5 4.0 2.0 1.520 1.580 4.000 4.012 1.475 1.500
MSM-0205-01 2.0 5.0 1.0 5.000 5.012 1.975 2.000
MSM-0205-02 2.0 5.0 2.0 2.020 2.080 5.000 5.012 1.975 2.000
MSM-0205-03 2.0 5.0 3.0 5.000 5.012 1.975 2.000
MSM-0206-03 2.5 6.0 3.0 2.520 2.580 6.000 6.012 2.475 2.500
MSM-0305-03 3.0 5.0 3.0 5.000 5.012 2.975 3.000
3.020 3.080
MSM-0305-04 3.0 5.0 4.0 5.000 5.012 2.975 3.000
MSM-0306-03 3.0 6.0 3.0 6.000 6.012 2.975 3.000
3.020 3.080
MSM-0306-04 3.0 6.0 4.0 6.000 6.012 2.975 3.000
MSM-0407-03 4.0 7.0 3.0 7.000 7.015 3.970 4.000
MSM-0407-04 4.0 7.0 4.0 4.030 4.105 7.000 7.015 3.970 4.000
MSM-0407-06 4.0 7.0 6.0 7.000 7.015 3.970 4.000
MSM-0408-04 4.0 8.0 4.0 8.000 8.015 3.970 4.000
4.030 4.105
MSM-0408-06 4.0 8.0 6.0 8.000 8.015 3.970 4.000
MSM-0508-04 5.0 8.0 4.0 8.000 8.015 4.970 5.000
MSM-0508-05 5.0 8.0 5.0 5.030 5.105 8.000 8.015 4.970 5.000
MSM-0508-08 5.0 8.0 8.0 8.000 8.015 4.970 5.000
MSM-0509-05 5.0 9.0 5.0 9.000 9.015 4.970 5.000
5.030 5.105
MSM-0509-08 5.0 9.0 8.0 9.000 9.015 4.970 5.000
MSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
MSM-0608-08 6.0 8.0 8.0 6.030 6.105 8.000 8.015 5.970 6.000
MSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
MSM-0609-06 6.0 9.0 6.0 6.030 6.105 9.000 9.015 5.970 6.000
MSM-0610-02 6.0 10.0 2.0 10.000 10.015 5.970 6.000
MSM-0610-04 6.0 10.0 4.0 10.000 10.015 5.970 6.000
MSM-0610-06 6.0 10.0 6.0 6.030 6.105 10.000 10.015 5.970 6.000
MSM-0610-08 6.0 10.0 8.0 10.000 10.015 5.970 6.000
MSM-0610-10 6.0 10.0 10.0 10.000 10.015 5.970 6.000
MSM-0611-04 6.0 11.0 4.0 6.030 6.105 11.000 11.018 5.970 6.000
MSM-0612-06 6.0 12.0 6.0 12.000 12.018 5.970 6.000
6.030 6.105
MSM-0612-10 6.0 12.0 10.0 12.000 12.018 5.970 6.000
MSM-0710-05 7.0 10.0 5.0 10.000 10.015 6.964 7.000
MSM-0710-08 7.0 10.0 8.0 7.040 7.130 10.000 10.015 6.964 7.000
MSM-0710-10 7.0 10.0 10.0 10.000 10.015 6.964 7.000
MSM-0711-16 7.0 11.0 16.0 7.040 7.130 11.000 11.018 6.964 7.000
MSM-0810-06 8.0 10.0 6.0 8.040 8.130 10.000 10.015 7.964 8.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
MSM-2025-30 20.0 25.0 30.0 20.065 20.195 25.000 25.021 19.948 20.000
MSM-2026-12 20.0 26.0 12.0 26.000 26.021 19.948 20.000
MSM-2026-15 20.0 26.0 15.0 26.000 26.021 19.948 20.000
20.065 20.195
MSM-2026-20 20.0 26.0 20.0 26.000 26.021 19.948 20.000
MSM-2026-30 20.0 26.0 30.0 26.000 26.021 19.948 20.000
MSM-2226-15 22.0 26.0 15.0 22.065 22.195 26.000 26.021 21.948 22.000
MSM-2228-10 22.0 28.0 10.0 28.000 28.021 21.948 22.000
MSM-2228-15 22.0 28.0 15.0 28.000 28.021 21.948 22.000
22.065 22.195
MSM-2228-20 22.0 28.0 20.0 28.000 28.021 21.948 22.000
MSM-2228-30 22.0 28.0 30.0 28.000 28.021 21.948 22.000
MSM-2430-15 24.0 30.0 15.0 30.000 30.025 23.948 24.000
MSM-2430-20 24.0 30.0 20.0 24.065 24.195 30.000 30.025 23.948 24.000
MSM-2430-30 24.0 30.0 30.0 30.000 30.025 23.948 24.000
MSM-2528-12 25.0 28.0 12.0 28.000 28.021 24.948 25.000
MSM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
MSM-2528-20 25.0 28.0 20.0 25.065 25.195 28.000 28.021 24.948 25.000
MSM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
MSM-2528-30 25.0 28.0 30.0 28.000 28.021 24.948 25.000
MSM-2530-20 25.0 30.0 20.0 30.000 30.025 24.948 25.000
MSM-2530-30 25.0 30.0 30.0 25.065 25.195 30.000 30.025 24.948 25.000
MSM-2530-40 25.0 30.0 40.0 30.000 30.025 24.948 25.000
MSM-2532-12 25.0 32.0 12.0 32.000 32.025 24.948 25.000
MSM-2532-20 25.0 32.0 20.0 32.000 32.025 24.948 25.000
MSM-2532-30 25.0 32.0 30.0 25.065 25.195 32.000 32.025 24.948 25.000
MSM-2532-35 25.0 32.0 35.0 32.000 32.025 24.948 25.000
MSM-2532-40 25.0 32.0 40.0 32.000 32.025 24.948 25.000
MSM-2630-20 26.0 30.0 20.0 26.065 26.195 30.000 30.025 25.948 26.000
MSM-2632-30 26.0 32.0 30.0 26.065 26.195 32.000 32.025 25.948 26.000
MSM-2734-20 27.0 34.0 20.0 34.000 34.025 26.948 27.000
MSM-2734-30 27.0 34.0 30.0 27.065 27.195 34.000 34.025 26.948 27.000
MSM-2734-40 27.0 34.0 40.0 34.000 34.025 26.948 27.000
MSM-2833-20 28.0 33.0 20.0 28.065 28.195 33.000 33.025 27.948 28.000
MSM-2836-20 28.0 36.0 20.0 36.000 36.025 27.948 28.000
MSM-2836-30 28.0 36.0 30.0 28.065 28.195 36.000 36.025 27.948 28.000
MSM-2836-40 28.0 36.0 40.0 36.000 36.025 27.948 28.000
MSM-3035-20 30.0 35.0 20.0 35.000 35.025 29.948 30.000
30.065 30.195
MSM-3035-40 30.0 35.0 40.0 35.000 35.025 29.948 30.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 139
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0,14 Min. Max. Min. Max. Min. Max.
MFM-0103-02 1.0 3.0 5.0 2.0 1.00 1.020 1.080 3.000 3.080 .975 1.000
MFM-0104-02 1.5 4.0 6.0 2.0 1.00 1.520 1.580 4.000 4.012 1.475 1.500
MFM-0205-03 2.0 5.0 8.0 3.0 1.50 2.020 2.080 5.000 5.012 1.975 2.000
MFM-0206-03 2.5 6.0 9.0 3.0 1.50 2.520 2.580 6.000 6.012 2.475 2.500
MFM-0306-04 3.0 6.0 9.0 4.0 1.50 3.020 3.080 6.000 6.012 2.975 3.000
MFM-0408-04 4.0 8.0 12.0 4.0 2.0 8.000 8.015 3.970 4.000
MFM-0408-06 4.0 8.0 12.0 6.0 2.0 4.030 4.105 8.000 8.015 3.970 4.000
MFM-0408-08 4.0 8.0 12.0 8.0 2.0 8.000 8.015 3.970 4.000
MFM-0509-05 5.0 9.0 13.0 5.0 2.0 9.000 9.015 4.970 5.000
MFM-0509-06 5.0 9.0 13.0 6.0 2.0 5.030 5.105 9.000 9.015 4.970 5.000
MFM-0509-08 5.0 9.0 13.0 8.0 2.0 9.000 9.015 4.970 5.000
MFM-0610-04 6.0 10.0 14.0 4.0 2.0 10.000 10.015 5.970 6.000
MFM-0610-06 6.0 10.0 14.0 6.0 2.0 6.030 6.105 10.000 10.015 5.970 6.000
MFM-0610-10 6.0 10.0 14.0 10.0 2.0 10.000 10.015 5.970 6.000
MFM-0611-04 6.0 11.0 4.0 4.0 2.5 6.030 6.105 11.000 11.018 5.970 6.000
MFM-0612-06 6.0 12.0 14.0 6.0 3.0 12.000 12.018 5.970 6.000
6.030 6.105
MFM-0612-10 6.0 12.0 14.0 10.0 3.0 12.000 12.018 5.970 6.000
MFM-0711-08 7.0 11.0 15.0 8.0 2.0 7.040 7.130 11.000 11.018 6.964 7.000
MFM-0811-05 8.0 11.0 13.0 5.0 2.0 11.000 11.018 7.964 8.000
8.040 8.130
MFM-0811-08 8.0 11.0 13.0 8.0 2.0 11.000 11.018 7.964 8.000
MFM-0812-06 8.0 12.0 16.0 6.0 2.0 12.000 12.018 7.964 8.000
MFM-0812-08 8.0 12.0 16.0 8.0 2.0 8.040 8.130 12.000 12.018 7.964 8.000
MFM-0812-12 8.0 12.0 16.0 12.0 2.0 12.000 12.018 7.964 8.000
MFM-0814-06 8.0 14.0 18.0 6.0 3.0 14.000 14.018 7.964 8.000
MFM-0814-10 8.0 14.0 18.0 10.0 3.0 14.000 14.018 7.964 8.000
8.040 8.130
MFM-081416-06 8.0 14.0 16.0 6.0 3.0 14.000 14.018 7.964 8.000
MFM-081416-10 8.0 14.0 16.0 10.0 3.0 14.000 14.018 7.984 8.000
MFM-0914-06 9.0 14.0 19.0 6.0 2.0 14.000 14.018 8.964 9.000
MFM-0914-10 9.0 14.0 19.0 10.0 2.0 9.040 9.130 14.000 14.018 8.964 9.000
MFM-0914-14 9.0 14.0 19.0 14.0 2.0 14.000 14.018 8.964 9.000
MFM-1014-10 10.0 14.0 19.0 10.0 2.0 14.000 14.018 9.964 10.000
MFM-1014-14 10.0 14.0 17.5 14.0 1.0 14.000 14.018 9.964 10.000
MFM-1014-19 10.0 14.0 17.5 19.0 1.0 14.000 14.018 9.964 10.000
MFM-1014-24 10.0 14.0 17.5 24.0 1.0 10.040 10.130 14.000 14.018 9.964 10.000
MFM-1014-34 10.0 14.0 17.5 34.0 1.0 14.000 14.018 9.964 10.000
MFM-101419-08 10.0 14.0 34.0 8.0 1.0 14.000 14.018 9.964 10.000
MFM-101420-12 10.0 14.0 20.0 12.0 2.0 14.000 14.018 9.964 10.000
30°
M F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 139
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0,14 Min. Max. Min. Max. Min. Max.
MFM-1016-06 10.0 16.0 22.0 6.0 3.0 16.000 16.018 9.964 10.000
MFM-1016-08 10.0 16.0 22.0 8.0 3.0 16.000 16.018 9.964 10.000
MFM-1016-10 10.0 16.0 22.0 10.0 3.0 16.000 16.018 9.964 10.000
10.040 10.130
MFM-1016-16 10.0 16.0 22.0 16.0 3.0 16.000 16.018 9.964 10.000
MFM-101620-06 10.0 16.0 20.0 6.0 3.0 16.000 16.018 9.964 10.000
MFM-101620-10 10.0 16.0 20.0 10.0 3.0 16.000 16.018 9.964 10.000
MFM-1216-10 12.0 16.0 22.0 10.0 2.0 16.000 16.018 11.957 12.000
12.050 12.160
MFM-1216-20 12.0 16.0 22.0 20.0 2.0 16.000 16.018 11.957 12.000
MFM-1218-08 12.0 18.0 24.0 8.0 3.0 18.000 18.018 11.957 12.000
MFM-1218-10 12.0 18.0 22.0 10.0 3.0 18.000 18.018 11.957 12.000
MFM-1218-12 12.0 18.0 24.0 12.0 3.0 12.050 12.160 18.000 18.018 11.957 12.000
MFM-1218-15 12.0 18.0 22.0 15.0 3.0 18.000 18.018 11.957 12.000
MFM-1218-20 12.0 18.0 22.0 20.0 3.0 18.000 18.018 11.957 12.000
MFM-1315-14 13.0 15.0 20.0 14.0 2.0 12.050 12.160 18.000 18.018 11.957 12.000
MFM-1420-07 14.0 20.0 25.0 7.0 3.0 20.000 20.021 13.957 14.000
MFM-1420-10 14.0 20.0 25.0 10.0 3.0 20.000 20.021 13.957 14.000
14.050 14.160
MFM-1420-15 14.0 20.0 25.0 15.0 3.0 20.000 20.021 13.957 14.000
MFM-1420-20 14.0 20.0 25.0 20.0 3.0 20.000 20.021 13.957 14.000
MFM-1521-10 15.0 21.0 27.0 10.0 3.0 21.000 21.021 14.957 15.000
MFM-1521-15 15.0 21.0 27.0 15.0 3.0 21.000 21.021 14.957 15.000
15.050 15.160
MFM-1521-20 15.0 21.0 27.0 20.0 3.0 21.000 21.021 14.957 15.000
MFM-1521-25 15.0 21.0 27.0 25.0 3.0 21.000 21.021 14.957 15.000
MFM-1618-12 16.0 18.0 24.0 12.0 1.0 16.050 16.160 18.000 18.021 15.957 16.000
MFM-1618-17 16.0 18.0 24.0 12.0 1.0 18.000 18.021 15.957 16.000
MFM-1622-12 16.0 22.0 28.0 12.0 3.0 22.000 22.021 15.957 16.000
MFM-1622-15 16.0 22.0 28.0 15.0 3.0 22.000 22.021 15.957 16.000
16.050 16.160
MFM-1622-20 16.0 22.0 28.0 20.0 3.0 22.000 22.021 15.957 16.000
MFM-1622-25 16.0 22.0 28.0 25.0 3.0 22.000 22.021 15.957 16.000
MFM-1824-08 18.0 24.0 30.0 8.0 3.0 24.000 24.021 17.957 18.000
MFM-1824-12 18.0 24.0 30.0 12.0 3.0 24.000 24.021 17.957 18.000
MFM-1824-18 18.0 24.0 30.0 18.0 3.0 18.050 18.160 24.000 24.021 17.957 18.000
MFM-1824-20 18.0 24.0 30.0 20.0 3.0 24.000 24.021 17.957 18.000
MFM-1824-30 18.0 24.0 30.0 30.0 3.0 24.000 24.021 17.957 18.000
MFM-202628-12 20.0 26.0 28.0 12.0 3.0 26.000 26.021 19.948 20.000
MFM-2026-15 20.0 26.0 32.0 15.0 3.0 26.000 26.021 19.948 20.000
20.065 20.195
MFM-2026-20 20.0 26.0 32.0 20.0 3.0 26.000 26.021 19.948 20.000
MFM-2026-30 20.0 26.0 32.0 30.0 3.0 26.000 26.021 19.948 20.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 139
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0,14 Min. Max. Min. Max. Min. Max.
MFM-2228-15 22.0 28.0 34.0 15.0 3.0 28.000 28.021 21.948 22.000
MFM-2228-20 22.0 28.0 34.0 20.0 3.0 22.065 22.195 28.000 28.021 21.948 22.000
MFM-2228-30 22.0 28.0 34.0 30.0 3.0 28.000 28.021 21.948 22.000
MFM-2430-15 24.0 30.0 36.0 15.0 3.0 30.000 30.025 23.948 24.000
MFM-2430-20 24.0 30.0 36.0 20.0 3.0 24.065 24.195 30.000 30.025 23.948 24.000
MFM-2430-30 24.0 30.0 36.0 30.0 3.0 30.000 30.025 23.948 24.000
MFM-2532-12 25.0 32.0 38.0 12.0 4.0 32.000 32.025 24.948 25.000
MFM-2532-15 25.0 32.0 38.0 15.0 4.0 32.000 32.025 24.948 25.000
25.065 25.195
MFM-2532-20 25.0 32.0 38.0 20.0 4.0 32.000 32.025 24.948 25.000
MFM-2532-30 25.0 32.0 38.0 30.0 4.0 32.000 32.025 24.948 25.000
MFM-2532-40 25.0 32.0 38.0 40.0 4.0 25.065 25.195 32.000 32.025 24.948 25.000
MFM-2734-20 27.0 34.0 40.0 20.0 4.0 34.000 34.025 26.948 27.000
MFM-2734-30 27.0 34.0 40.0 30.0 4.0 27.065 27.195 34.000 34.025 26.948 27.000
MFM-2734-40 27.0 34.0 40.0 40.0 4.0 34.000 34.025 26.948 27.000
MFM-2836-20 28.0 36.0 42.0 20.0 4.0 36.000 36.025 27.948 28.000
MFM-2836-30 28.0 36.0 42.0 30.0 4.0 28.065 28.195 36.000 36.025 27.948 28.000
MFM-2836-40 28.0 36.0 42.0 40.0 4.0 36.000 36.025 27.948 28.000
MFM-3035-20 30.0 35.0 44.0 20.0 4.0 30.060 30.195 35.000 35.025 29.948 30.000
MFM-3038-20 30.0 38.0 44.0 20.0 4.0 38.000 38.025 29.948 30.000
MFM-3038-30 30.0 38.0 44.0 30.0 4.0 30.065 30.195 38.000 38.025 29.948 30.000
MFM-3038-40 30.0 38.0 44.0 40.0 4.0 38.000 38.025 29.948 30.000
MFM-3240-20 32.0 40.0 46.0 20.0 4.0 40.000 40.025 31.938 32.000
MFM-3240-30 32.0 40.0 46.0 30.0 4.0 32.080 32.240 40.000 40.025 31.938 32.000
MFM-3240-40 32.0 40.0 46.0 40.0 4.0 40.000 40.025 31.938 32.000
159
iglide®
R iglide® R - Low-cost, low-wear
Cost-effective
Mechanical Properties
Modulus of elasticity psi 282,800 DIN 53457
Tensile strength at 68°F psi 10,150 DIN 53452
Compressive strength psi 9,863
Permissible static surface pressure (68°F) psi 3,336
Shore D-hardness 77 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 10
9
iglide® R plain bearings were developed mainly for low to average radial 8
loads. The graph shows the elastic deformation of iglide® R for radial 7
4
value. However, it is also a result of the cycle time.
3
2
➤ Compressive strength, Page 63
1
0
Pressure (psi)
140°F 73°F
Temperatures 3,626
The maximum permissible short-term temperature is 230°F, and the long- 2,901
term application temperature is 194°F. With increasing temperatures, the
2,176
compression resistance of iglide® R plain bearings decreases. The ambient
temperatures prevalent in the bearing system also have an effect on the
1,450
bearing wear. With increasing temperatures, the wear increases.
Pressure (psi)
725
➤ Application temperatures, Page 67
0
68 86 104 122 140 158 176 194
Temperature (°F)
iglide® R Application Temperature
Minimum - 58°F Recommended maximum permissible static surface
pressure of iglide® R as a result of the temperature
Max. long-term +194°F
Max. short-term +230°F
Additional axial securing +122°F
Temperature limits for iglide R ®
0.30
0.5 0.25
Coefficient of friction µ
0.20
0.4
0.15
Coefficient of friction µ
0.10
0.3
0.05
0.2 0.00
Pressure (psi)
0.1
0.3
Coefficient of friction µ
Oil 0.04
0.0
Water 0.04 0 12 24 36 48 60
(Shaft finish = 40 rms, 50 HRC) Coefficient of friction for iglide ® R as a result of the
shaft surface (shaft Cold Rolled Steel)
Shaft Materials 8
The graphs show results of testing different shaft materials with plain bear- 6
ings made of iglide® R.
In the low load range, the 440B, hard anodized aluminum, 1050 case hardened 4
steel, free cutting and hard chromed shafts are the most suitable shafting
Wear (µm/km)
partners for iglide® R plain bearings. At higher loads, hardened shafts such
2
as 440B and 1050 case hardened steel are recommended.
4.0 10
3.5 9
8
Hard anodized aluminum
3.0
7
Automatic screw steel
2.5 6
1050, hard chromed
5
2.0
HR carbon steel
4
304 Stainless
Wear (µm/km)
1.5
Wear (µm/km)
3
1050 Steel
1.0 2
440B
1
0.5
0
0.0 1050 304 Stainless HR Carbon Hard
Steel Steel Steel Chromed
Wear for iglide® R, rotating with different shaft materials, Pivoting Oscillating
p = 108 psi, v = 98 fpm
Wear for oscillating and rotating applications with
different shaft materials at p = 290 psi
30°
>18 to 30 -0 /-330
Length of chamfer Length >30 to 50 -0 /-390
>50 to 80 -0 /-460
Medium Resistance
+ resistant, 0 conditionally resistant, – not resistant 0.0 0.2 0.4 0.6 0.8 1.0 1.2
Radiation Resistance
Plain bearings made from iglide® R are resistant to radiation up to an intensity of 3 x 102 Gy.
UV Resistance
iglide® R plain bearings are resistant to UV radiation, but the tribological properties are lessened with permanent exposure.
Vacuum
In a vacuum environment, iglide® R plain bearings release gases. It is only possible to use iglide® R in vacuum to a limited extent.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
RSI-0204-04 1/8 1/4 1/4 .1262 .1280 .2510 .2515 .1241 .1250
RSI-0305-03 3/16 5/16 3/16 .3122 .3128 .1862 .1874
RSI-0305-04 3/16 5/16 1/4 .3122 .3128 .1862 .1874
.1886 1.915
RSI-0305-06 3/16 5/16 3/8 .3122 .3128 .1862 .1874
RSI-0305-08 3/16 5/16 1/2 .3122 .3128 .1862 .1874
RSI-0406-04 1/4 3/8 1/4 .3760 .3766 .2486 .2500
RSI-0406-05 1/4 3/8 5/16 .3760 .3766 .2486 .2500
RSI-0406-06 1/4 3/8 3/8 .2516 .2551 .3760 .3766 .2486 .2500
RSI-0406-10 1/4 3/8 5/8 .3760 .3766 .2486 .2500
RSI-0406-12 1/4 3/8 3/4 .3760 .3766 .2486 .2500
RSI-0506-08 5/16 3/8 1/2 .3747 .3753 .3106 .3115
.3125 .3148
RSI-0506-12 5/16 3/8 3/4 .3747 .3753 .3106 .3115
RSI-0507-04 5/16 7/16 1/4 .4386 .4393 .3112 .3126
RSI-0507-05 5/16 7/16 5/16 .4386 .4393 .3112 .3126
RSI-0507-06 5/16 7/16 3/8 .4386 .4393 .3112 .3126
.3142 .3177
RSI-0507-08 5/16 7/16 1/2 .4386 .4393 .3112 .3126
RSI-0507-10 5/16 7/16 5/8 .4386 .4393 .3112 .3126
RSI-0507-12 5/16 7/16 3/4 .4386 .4393 .3112 .3126
RSI-0608-04 3/8 1/2 1/4 .5010 .5017 .3734 .3748
RSI-0608-06 3/8 1/2 3/8 .5010 .5017 .3734 .3748
RSI-0608-08 3/8 1/2 1/2 .5010 .5017 .3734 .3748
.3764 .3799
RSI-0608-10 3/8 1/2 5/8 .5010 .5017 .3734 .3748
RSI-0608-12 3/8 1/2 3/4 .5010 .5017 .3734 .3748
RSI-0608-16 3/8 1/2 1 .5010 .5017 .3734 .3748
RSI-0708-08 7/8 17/32 1/2 .4379 .4406 .5309 .5316 .4366 .4375
RSI-0810-04 1/2 5/8 1/4 .6250 .6257 .4983 .5000
RSI-0810-06 1/2 5/8 3/8 .6250 .6257 .4983 .5000
RSI-0810-08 1/2 5/8 1/2 .6250 .6257 .4983 .5000
.5020 .5063
RSI-0810-10 1/2 5/8 5/8 .6250 .6257 .4983 .5000
RSI-0810-12 1/2 5/8 3/4 .6250 .6257 .4983 .5000
RSI-0810-16 1/2 5/8 1 .6250 .6257 .4983 .5000
RSI-0812-12 1/2 3/4 3/4 .7500 .7508 .4983 .5000
.5020 .5047
RSI-0812-16 1/2 3/4 1 .7500 .7508 .4983 .5000
RSI-1012-04 5/8 3/4 1/4 .7500 .7508 .6231 .6248
RSI-1012-06 5/8 3/4 3/8 .7500 .7508 .6231 .6248
.6268 .6311
RSI-1012-08 5/8 3/4 1/2 .7500 .7508 .6231 .6248
RSI-1012-10 5/8 3/4 5/8 .7500 .7508 .6231 .6248
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 163
Inch
*Based on steel housing bore
RFI-0305-03 3/16 5/16 3/16 .370 .047 .3125 .3131 .1862 .1874
RFI-0305-04 3/16 5/16 1/4 .370 .047 .3125 .3131 .1862 .1874
.1886 .1915
RFI-0305-06 3/16 5/16 3/8 .370 .047 .3125 .3131 .1862 .1874
RFI-0305-08 3/16 5/16 1/2 .370 .047 .3125 .3131 .1862 .1874
RFI-0406-04 1/4 3/8 1/4 .560 .047 .3750 .3756 .2486 .2500
RFI-0406-05 1/4 3/8 5/16 .560 .047 .3750 .3756 .2486 .2500
RFI-0406-06 1/4 3/8 3/8 .560 .047 .3750 .3756 .2486 .2500
.2516 .2551
RFI-0406-08 1/4 3/8 1/2 .560 .047 .3750 .3756 .2486 .2500
RFI-0406-10 1/4 3/8 5/8 .560 .047 .3750 .3756 .2486 .2500
RFI-0406-12 1/4 3/8 3/4 .560 .047 .3750 .3756 .2486 .2500
RFI-0507-04 5/16 7/16 1/4 .560 .062 .4374 .4381 .3112 .3126
RFI-0507-05 5/16 7/16 5/16 .560 .062 .4374 .4381 .3112 .3126
RFI-0507-06 5/16 7/16 3/8 .560 .062 .4374 .4381 .3112 .3126
.3142 .3177
RFI-0507-08 5/16 7/16 1/2 .560 .062 .4374 .4381 .3112 .3126
RFI-0507-10 5/16 7/16 5/8 .560 .062 .4374 .4381 .3112 .3126
RFI-0507-12 5/16 7/16 3/4 .560 .062 .4374 .4381 .3112 .3126
RFI-0607-04 3/8 15/32 1/4 .687 .046 .3766 .3801 .4687 .4694 .3736 .3750
RFI-0608-04 3/8 1/2 1/4 .625 .062 .5010 .5017 .3736 .3750
RFI-0608-06 3/8 1/2 3/8 .625 .062 .5010 .5017 .3736 .3750
RFI-0608-08 3/8 1/2 1/2 .625 .062 .5010 .5017 .3736 .3750
.3766 .3801
RFI-0608-10 3/8 1/2 5/8 .625 .062 .5010 .5017 .3736 .3750
RFI-0608-12 3/8 1/2 3/4 .625 .062 .5010 .5017 .3736 .3750
RFI-0608-16 3/8 1/2 1 .625 .062 .5010 .5017 .3736 .3750
RFI-0708-04 7/16 17/32 1/4 .750 .046 .5309 .5316 .4349 .4366
.4386 .4429
RFI-0708-08 7/16 17/32 1/2 .750 .046 .5309 .5316 .4349 .4366
RFI-0809-03 1/2 19/32 3/16 .875 .046 .5937 .5944 .4980 .4990
RFI-0809-04 1/2 19/32 1/4 .875 .046 .5020 .5063 .5937 .5944 .4980 .4990
RFI-0809-08 1/2 19/32 1/2 .875 .046 .5937 .5944 .4980 .4990
RFI-0810-04 1/2 5/8 1/4 .875 .062 .6250 .6257 .4983 .5000
RFI-0810-06 1/2 5/8 3/8 .875 .062 .6250 .6257 .4983 .5000
RFI-0810-08 1/2 5/8 1/2 .875 .062 .6250 .6257 .4983 .5000
.5020 .5063
RFI-0810-10 1/2 5/8 5/8 .875 .062 .6250 .6257 .4983 .5000
RFI-0810-12 1/2 5/8 3/4 .875 .062 .6250 .6257 .4983 .5000
RFI-0810-16 1/2 5/8 1 .875 .062 .6250 .6257 .4983 .5000
RFI-0812-0210 1/2 3/4 7/32 1.000 .125 .7500 .7508 .4983 .5000
RFI-0812-08 1/2 3/4 1/2 1.000 .125 .5020 .5047 .7500 .7508 .4983 .5000
RFI-0812-12 1/2 3/4 3/4 1.000 .125 .7500 .7508 .4983 .5000
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 163
Inch
*Based on steel housing bore
RFI-0812-16 1/2 3/4 1 1.000 .125 .5020 .5047 .7500 .7508 .4983 .5000
RFI-1012-06 5/8 3/4 3/8 1.000 .062 .7500 .7508 .6233 .6250
RFI-1012-08 5/8 3/4 1/2 1.000 .062 .7500 .7508 .6233 .6250
RFI-1012-10 5/8 3/4 5/8 1.000 .062 .6270 .6313 .7500 .7508 .6233 .6250
RFI-1012-12 5/8 3/4 3/4 1.000 .062 .7500 .7508 .6233 .6250
RFI-1012-16 5/8 3/4 1 1.000 .062 .7500 .7508 .6233 .6250
RFI-1214-07 3/4 7/8 7/16 1.125 .062 .8748 .8756 .7480 .7500
RFI-1214-08 3/4 7/8 7/16 1.125 .062 .8748 .8756 .7480 .7500
.7516 .7549
RFI-1214-12 3/4 7/8 7/16 1.125 .062 .8748 .8756 .7480 .7500
RFI-1214-16 3/4 7/8 7/16 1.125 .062 .8748 .8756 .7480 .7500
RFI-1216-08 3/4 1 1/2 1.250 .156 1.0000 1.0008 .7480 .7500
RFI-1216-12 3/4 1 3/4 1.250 .156 1.0000 1.0008 .7480 .7500
RFI-1216-16 3/4 1 1 1.250 .156 .7526 .7577 1.0000 1.0008 .7480 .7500
RFI-1216-20 3/4 1 1 1/4 1.250 .156 1.0000 1.0008 .7480 .7500
RFI-1216-24 3/4 1 1 1/2 1.250 .156 1.0000 1.0008 .7480 .7500
RFI-1416-07 7/8 1 7/16 1.250 .062 .9997 1.0005 .8720 .8740
RFI-1416-12 7/8 1 7/16 1.250 .062 .8756 .8789 .9997 1.0005 .8720 .8740
RFI-1416-20 7/8 1 7/16 1.250 .062 .9997 1.0005 .8720 .8740
RFI-1418-10 7/8 1 1/8 5/8 1.375 .156 1.1250 1.1258 .8728 .8748
RFI-1418-12 7/8 1 1/8 3/4 1.375 .156 1.1250 1.1258 .8728 .8748
.8774 .8825
RFI-1418-16 7/8 1 1/8 1 1.375 .156 1.1250 1.1258 .8728 .8748
RFI-1418-24 7/8 1 1/8 1 1/2 1.375 .156 1.1250 1.1258 .8728 .8748
RFI-1618-08 1 1 1/8 1/2 1.375 .062 1.1250 1.1258 .9980 1.0000
RFI-1618-12 1 1 1/8 3/4 1.375 .062 1.0026 1.0077 1.1250 1.1258 .9980 1.0000
RFI-1618-20 1 1 1/8 1 1/4 1.375 .062 1.1250 1.1258 .9980 1.0000
RFI-1620-10 1 1 1/4 5/8 1.500 .188 1.2500 1.2510 .9980 1.0000
RFI-1620-12 1 1 1/4 3/4 1.500 .188 1.2500 1.2510 .9980 1.0000
RFI-1620-16 1 1 1/4 1 1.500 .188 1.0026 1.0077 1.2500 1.2510 .9980 1.0000
RFI-1620-20 1 1 1/4 1 1/4 1.500 .188 1.2500 1.2510 .9980 1.0000
RFI-1620-24 1 1 1/4 1 1/2 1.500 .188 1.2500 1.2510 .9980 1.0000
RFI-2022-09 1 1/4 1 13/32 9/16 1.687 .078 1.2508 1.2547 1.4098 1.4108 1.2464 1.2488
RFI-2024-16 1 1/4 1 1/2 1 1.750 .200 1.2531 1.2594 1.5039 1.5049 1.2476 1.2500
RFI-2428-12 1 1/2 1 3/4 3/4 2.000 .125 1.5031 1.5094 1.7575 1.7585 1.4976 1.5000
RFI-3236-12 2 2 1/4 3/4 2.500 .125 2.2579 2.2591 1.9971 2.0000
RFI-3236-24 2 2 1/4 1 1/2 2.500 .125 2.0039 2.0114 2.2579 2.2591 1.9971 2.0000
RFI-3236-32 2 2 1/4 2 2.500 .125 2.2579 2.2591 1.9971 2.0000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
RSM-0203-07 2.0 3.6 7.0 2.014 2.054 3.600 3.610 1.975 2.000
RSM-0405-04 4.0 5.5 4.0 4.068 4.020 5.500 5.512 3.970 4.000
RSM-0506-05 5.0 6.0 5.0 6.000 6.012 4.970 5.000
5.020 5.068
RSM-0506-07 5.0 6.0 7.0 6.000 6.012 4.970 5.000
RSM-0507-05 5.0 7.0 5.0 5.020 5.068 7.000 7.012 4.970 5.000
RSM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
RSM-0610-08 6.0 10.0 8.0 10.000 10.015 5.970 6.000
6.020 6.068
RSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
RSM-1012-05 10.0 12.0 5.0 12.000 12.018 9.964 10.000
RSM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
RSM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
RSM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
RSM-1416-10 14.0 16.0 10.0 16.000 16.018 13.957 14.000
14.032 14.102
RSM-1416-15 14.0 16.0 15.0 16.000 16.018 13.957 14.000
RSM-1517-15 15.0 17.0 15.0 15.032 15.102 17.000 17.0178 15.957 16.000
RSM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
RSM-1820-25 18.0 20.0 25.0 18.032 18.102 20.000 20.021 17.957 18.000
RSM-2023-15 20.0 23.0 15.0 23.000 23.021 19.948 20.000
20.040 20.124
RSM-2023-20 20.0 23.0 20.0 23.000 23.021 19.948 20.000
RSM-2528-25 25.0 28.0 25.0 25.040 25.124 28.000 28.021 24.948 25.000
RSM-2832-12 28.0 32.0 12.0 28.065 28.195 32.000 32.025 27.948 28.000
RSM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
30.040 30.124
RSM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000
RSM-3539-30 35.0 39.0 30.0 35.050 35.150 39.000 39.025 34.938 35.000
30°
R F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 163
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 b1 d3 b2 I.D. After Pressfit* Housing Bore Shaft Size
h13 d13 -0.14 Min. Max. Min. Max. Min. Max.
RFM-0405-03 4.0 5.0 3.0 9.0 0.5 4.020 4.068 5.000 5.012 3.975 4.000
RFM-0507-05 5.0 7.0 5.0 11.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
RFM-0608-06 6.0 8.0 6.0 12.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
RFM-0810-05 8.0 10.0 5.0 15.0 1.0 10.000 10.015 7.964 8.000
8.025 8.083
RFM-0810-10 8.0 10.0 10.0 15.0 1.0 10.000 10.015 7.964 8.000
RFM-1012-09 10.0 12.0 9.0 18.0 1.0 12.000 12.018 9.964 10.000
RFM-1012-10 10.0 12.0 10.0 18.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
RFM-1012-18 10.0 12.0 18.0 18.0 1.0 12.000 12.018 9.964 10.000
RFM-1214-10 12.0 14.0 10.0 20.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
RFM-1214-12 12.0 14.0 12.0 20.0 1.0 14.000 14.018 11.957 12.000
RFM-1416-17 14.0 16.0 17.0 22.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
RFM-1517-17 15.0 17.0 17.0 23.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
RFM-1618-17 16.0 18.0 17.0 24.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
RFM-1622-12 16.0 22.0 12.0 24.0 3.0 16.032 16.102 22.000 22.021 15.957 16.000
RFM-1820-17 18.0 20.0 17.0 26.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
RFM-2023-21 20.0 23.0 21.0 30.0 1.5 20.040 20.124 23.000 23.021 19.948 20.000
RFM-222529-045 22.0 25.0 4.5 29.0 1.5 22.040 22.124 25.000 25.021 21.948 22.000
RFM-2528-21 25.0 28.0 21.5 35.0 1.5 25.040 25.124 28.000 28.021 24.948 25.000
171
iglide®
L280 iglide® L280 - The Marathon Runner
Low wear on all shafts
Mechanical Properties
Modulus of elasticity psi 507,600 DIN 53457
Tensile strength at 68°F psi 18,130 DIN 53452
Compressive strength psi 8,847
Permissible static surface pressure (68°F) psi 8,702
Shore D-hardness 77 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength
8
iglide® L280 exhibits a very high compression resistance in spite of its
high elasticity. The graph shows the elastic deformation of iglide® L280 6
under radial loading. At the maximum permissible load of 8700 psi, the
deformation at room temperature is less than 3%. 4
Deformation (%)
Temperatures 17,400
14,500
iglide ® L280 plain bearings show minimal reaction to changing external
conditions. This also applies to temperatures. iglide ® L280 bearings maintain 11,600
their exceptional wear resistance even up to the highest permissible application
temperatures and at the same time resist becoming brittle at low temperatures. 8,702
Pressure (psi)
On the other hand, the mechanical properties at high temperatures limit the 5,802
applicationS of iglide® L280. Even at temperatures of 140°F, relaxation of the
bearing can occur. In this process, the pressfit forces of the bearing decrease to 2,901
a large extent due to temperature. During re-cooling and the resulting contraction 0
caused by it, migration of the bearing can occur. 68 86 104 122 140 158 176 194
In order to avoid this situation, iglide® L280 plain bearings always need to be Temperature (°F)
axially secured in applications at 140°F and above.
Recommended maximum permissible static surface
➤ Application temperatures, Page 67 pressure of iglide® L280 as a result of temperature
0.20
0. 4
0.15
Coefficient of friction µ
0.10
0. 3 0.05
0.00
0 1450 2900 4350 5800 7250 8700
0. 2 Pressure (psi)
9.84 19.68 29.53 39.37 49.22 59.05 68.90
Surface Speed (fpm) Coefficient of friction of iglide® L280 as a result of the
load, v = 1.97 fpm
Coefficient of friction of iglide® L280 as a result of the sur-
face speed, p = 108 psi, shaft made of Cold Rolled Steel 0.35
Coefficient of friction µ
0.30
Coefficient of friction for iglide® L280 against steel (Shaft Finish = Coefficients of friction for iglide® L280 as a result of the
40 rms, 50 HRC) shaft surface (shaft Cold Rolled Steel)
The graphs show results of testing different shaft materials with plain bear- 2.0
ings made of iglide® L280.
For rotational applications with low loads, the wear varies according to the 1.5
shaft material. iglide® L280 provides very good to acceptable coefficients of
friction for all shafts that were tested. iglide® L280 likes hard shafts. For small 1.0
Wear (µm/km)
radial loads with hard-chromed shafts and/or shafts made of corrosion-re-
sistant steel, iglide® L280 is the best suited iglide® material. 0.5
The soft shaft materials HR carbon steel and free-cutting steel are not as well
suited for plain bearings made of iglide® L280. 0.0
0.0 145 290 435 580 725
Hardened shafts are preferred for applications for higher loads. The graph
Pressure (psi)
clearly shows the difference in materials for increasing loads. A similar picture
emerges for oscillating applications. First, for low loads, the wear for the os- 1050 Steel 304 SS
cillating movement lies below that of a rotation at the same load. For higher HR carbon steel Hard chromed
loads, the situation changes.
Wear with different shaft materials in rotational
If the shaft material you plan to use is not contained in this listing, please
operation, as a result of the load
contact us.
70
➤ Shaft Materials, Page 71
60
50
1.6 40
1.4 30
1.2 Wear (µm/km)
Hard anodized aluminum
20
Automatic screw steel
1.0
1050, hard chromed
10
0.8
HR Carbon Steel
0
304 Stainless
1050 Steel
0.0
Wear for oscillating and rotating applications with
Wear of iglide® L280 with different shaft materials shaft material Cold Rolled Steel, as a result of the load
(p = 108 psi)
Chemical Resistance
iglide® L280 plain bearings have a good resistance to chemicals. They are resistant to most lubricants. iglide® L280 is not attacked by most weak
organic and inorganic acids.
The moisture absorption of iglide® L280 plain bearings is approximately 1.3% weight in the standard atmosphere. The maximum water absorption
is 6.5%. This must be taken into account along with other environmental influences.
➤ Chemical table, Page 1364
Medium Resistance 0. 7
Strong alkaline 0 0. 0
0. 0 0 .8 1 1 .6 3 2 .4 4 3 .2 5 4 .0 6 4 .8 8 5 .6 9 6 .5
+ resistant, 0 conditionally resistant, – not resistant
Moistur e Absorption (weight %)
Chemical resistance of iglide® L280 Effect of moisture absorption on iglide ® L280 plain
All data given concerns the chemical resistance at room temperature bearings
(68°F). For a complete list, see Page 1364
Radiation Resistance
Plain bearings made from iglide® L280 are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® L280 plain bearings are permanently resistant to UV radiation. A slight change in color (dark coloration) due to UV radiation
and other weathering effects will not significantly influence the mechanical, electrical or thermal properties.
Vacuum
In a vacuum, iglide® L280 plain bearings will outgas any moisture they may have absorbed. The use of iglide® L280 in a vacuum
environment is only possible to a limited extent.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 175
Inch
*Based on steel housing bore
LFI-0203-03 1/8 3/16 3/16 .312 .032 .1873 .1878 .1236 .1243
LFI-0203-04 1/8 3/16 1/4 .312 .032 .1251 .1269 .1873 .1878 .1236 .1243
LFI-0203-06 1/8 3/16 3/8 .312 .032 .1873 .1878 .1236 .1243
LFI-0304-02 3/16 1/4 1/8 .375 .032 .2497 .2503 .1858 .1865
LFI-0304-04 3/16 1/4 1/4 .375 .032 .2497 .2503 .1858 .1865
.1873 .1892
LFI-0304-06 3/16 1/4 3/8 .375 .032 .2497 .2503 .1858 .1865
LFI-0304-08 3/16 1/4 1/2 .375 .032 .2497 .2503 .1858 .1865
LFI-0405-04 1/4 5/16 1/4 .500 .032 .3122 .3128 .2481 .2490
LFI-0405-05 1/4 5/16 5/16 .500 .032 .3122 .3128 .2481 .2490
LFI-0405-06 1/4 5/16 3/8 .500 .032 .2498 .2521 .3122 .3128 .2481 .2490
LFI-0405-08 1/4 5/16 1/2 .500 .032 .3122 .3128 .2481 .2490
LFI-0405-12 1/4 5/16 3/4 .500 .032 .3122 .3128 .2481 .2490
LFI-0506-04 5/16 3/8 1/4 .562 .032 .3747 .3753 .3106 .3115
LFI-0506-06 5/16 3/8 3/8 .562 .032 .3747 .3753 .3106 .3115
.3125 .3148
LFI-0506-08 5/16 3/8 1/2 .562 .032 .3747 .3753 .3106 .3115
LFI-0506-12 5/16 3/8 3/4 .562 .032 .3747 .3753 .3106 .3115
LFI-0607-04 3/8 15/32 1/4 .687 .046 .4684 .4691 .3731 .3740
LFI-0607-06 3/8 15/32 3/8 .687 .046 .4684 .4691 .3731 .3740
LFI-0607-08 3/8 15/32 1/2 .687 .046 .4684 .4691 .3731 .3740
.3750 .3773
LFI-0607-12 3/8 15/32 3/4 .687 .046 .4684 .4691 .3731 .3740
LFI-0607-14 3/8 15/32 7/8 .687 .046 .4684 .4691 .3731 .3740
LFI-0607-24 3/8 15/32 1 1/2 .687 .046 .4684 .4691 .3731 .3740
LFI-0708-04 7/16 17/32 1/4 .750 .046 .5309 .5316 .4355 .4365
.4379 .4406
LFI-0708-08 7/16 17/32 1/2 .750 .046 .5309 .5316 .4355 .4365
LFI-0809-04 1/2 19/32 1/4 .875 .046 .5934 .5941 .4980 .4990
LFI-0809-06 1/2 19/32 3/8 .875 .046 .5934 .5941 .4980 .4990
LFI-0809-08 1/2 19/32 1/2 .875 .046 .5003 .5030 .5934 .5941 .4980 .4990
LFI-0809-12 1/2 19/32 3/4 .875 .046 .5934 .5941 .4980 .4990
LFI-0809-16 1/2 19/32 1 .875 .046 .5934 .5941 .4980 .4990
LFI-1011-045 5/8 23/32 9/32 .937 .046 .7184 .7192 .6230 .6240
LFI-1011-08 5/8 23/32 1/2 .937 .046 .7184 .7192 .6230 .6240
LFI-1011-12 5/8 23/32 3/4 .937 .046 .6253 .6280 .7184 .7192 .6230 .6240
LFI-1011-16 5/8 23/32 1 .937 .046 .7184 .7192 .6230 .6240
LFI-1011-24 5/8 23/32 1 1/2 .937 .046 .7184 .7192 .6230 .6240
LFI-1214-08 3/4 7/8 1/2 1.125 .062 .8747 .8755 .7479 .7491
LFI-1214-10 3/4 7/8 5/8 1.125 .062 .7507 .7541 .8747 .8755 .7479 .7491
LFI-1214-12 3/4 7/8 3/4 1.125 .062 .8747 .8755 .7479 .7491
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 175
Inch
*Based on steel housing bore
iglide®
L280 iglide® L280 - Product Range
Thrust washer - Inch d4
d5
d1
Type Dimensions
S
Order key
d2 L T I -05 09- 006
d6
Thickness s (inch)
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
Form T (washer)
iglide® material
h
d5
d4
Inch
d6
Part Number d1 d2 s d4 d5 h d6
h
+.010 -.010 -.0020 +-.005 +.015 +.005 +.008 +.005
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
LSM-0203-03 2.0 3.5 3.0 2.014 2.054 3.500 3.510 1.975 2.000
LSM-0204-03 2.5 4.0 3.0 2.514 2.554 4.000 4.012 2.475 2.500
LSM-0304-03 3.0 4.5 3.0 4.500 4.512 2.975 3.000
LSM-0304-05 3.0 4.5 5.0 3.014 3.054 4.500 4.512 2.975 3.000
LSM-0304-06 3.0 4.5 6.0 4.500 4.512 2.975 3.000
LSM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
LSM-0405-06 4.0 5.5 6.0 5.500 5.512 3.970 4.000
4.020 4.068
LSM-0405-08 4.0 5.5 8.0 5.500 5.512 3.970 4.000
LSM-0405-10 4.0 5.5 10.0 5.500 5.512 3.970 4.000
LSM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
LSM-0507-08 5.0 7.0 8.0 5.020 5.068 7.000 7.015 4.970 5.000
LSM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
LSM-0607-14 6.0 7.0 14.0 6.010 6.040 7.000 7.015 5.970 6.000
LSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
LSM-0608-08 6.0 8.0 8.0 8.000 8.015 5.970 6.000
LSM-0608-09 6.0 8.0 9.5 8.000 8.015 5.970 6.000
6.020 6.068
LSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
LSM-0608-11 6.0 8.0 11.8 8.000 8.015 5.970 6.000
LSM-0608-13 6.0 8.0 13.8 8.000 8.015 5.970 6.000
LSM-0709-09 7.0 9.0 9.0 9.000 9.015 6.964 7.000
7.025 7.083
LSM-0709-12 7.0 9.0 12.0 9.000 9.015 6.964 7.000
LSM-0810-06 8.0 10.0 6.0 10.000 10.015 7.964 8.000
LSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
LSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
LSM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
LSM-0810-13 8.0 10.0 13.8 8.025 8.083 10.000 10.015 7.964 8.000
LSM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
LSM-0810-16 8.0 10.0 16.0 10.000 10.015 7.964 8.000
LSM-0810-20 8.0 10.0 20.0 10.000 10.015 7.964 8.000
LSM-0810-21 8.0 10.0 21.0 10.000 10.015 7.964 8.000
LSM-0911-06 9.0 11.0 6.0 9.025 9.083 11.000 11.018 8.964 9.000
LSM-1012-04 10.0 12.0 4.0 12.000 12.018 9.964 10.000
LSM-1012-06 10.0 12.0 6.0 12.000 12.018 9.964 10.000
LSM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
10.025 10.083
LSM-1012-09 10.0 12.0 9.0 12.000 12.018 9.964 10.000
LSM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
LSM-1012-12 10.0 12.0 12.0 12.000 12.018 9.964 10.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
LSM-2528-30 25.0 28.0 30.0 25.040 25.124 28.000 28.021 24.948 25.000
LSM-2630-16 26.0 30.0 16.0 30.000 30.021 25.948 26.000
26.040 26.124
LSM-2630-25 26.0 30.0 25.0 30.000 30.021 25.948 26.000
LSM-2830-10 28.0 30.0 10.0 28.040 28.124 30.000 30.021 27.948 28.000
LSM-2831-10 28.0 31.0 10.0 28.040 28.124 31.000 31.025 27.948 28.000
LSM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
LSM-2832-25 28.0 32.0 25.0 28.040 28.124 32.000 32.025 27.948 28.000
LSM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
LSM-3034-16 30.0 34.0 16.0 34.000 34.025 29.948 30.000
LSM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
LSM-3034-24 30.0 34.0 24.0 34.000 34.025 29.948 30.000
LSM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
LSM-3034-30 30.0 34.0 30.0 30.040 30.124 34.000 34.025 29.948 30.000
LSM-3034-36 30.0 34.0 36.0 34.000 34.025 29.948 30.000
LSM-3034-38 30.0 34.0 38.0 34.000 34.025 29.948 30.000
LSM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
LSM-3034-47 30.0 34.0 47.0 34.000 34.025 29.948 30.000
LSM-3236-20 32.0 36.0 20.0 36.000 36.025 31.938 32.000
LSM-3236-25 32.0 36.0 25.0 36.000 36.025 31.938 32.000
32.050 32.150
LSM-3236-30 32.0 36.0 30.0 36.000 36.025 31.938 32.000
LSM-3236-40 32.0 36.0 40.0 36.000 36.025 31.938 32.000
LSM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
LSM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.050 35.150
LSM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
LSM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
LSM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
LSM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.050 40.150
LSM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
LSM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
LSM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
LSM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.050 45.150
LSM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
LSM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
LSM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
LSM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
50.050 50.150
LSM-5055-40 50.0 55.0 40.0 55.000 55.030 49.938 50.000
LSM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
L F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 175
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
LFM-0304-03 3.0 4.5 7.5 3.0 0.75 4.500 4.512 2.975 3.000
3.014 3.054
LFM-0304-05 3.0 4.5 7.5 5.0 0.75 4.500 4.512 2.975 3.000
LFM-0405-03 4.0 5.5 9.5 3.0 0.75 5.500 5.512 3.970 4.000
LFM-0405-04 4.0 5.5 9.5 4.0 0.75 4.020 4.068 5.500 5.512 3.970 4.000
LFM-0405-06 4.0 5.5 9.5 6.0 0.75 5.500 5.512 3.970 4.000
LFM-0506-08 5.0 6.0 10.0 8.0 0.5 5.010 5.040 6.000 6.012 4.970 5.000
LFM-0507-04 5.0 7.0 11.0 4.0 1.0 7.000 7.015 4.970 5.000
5.020 5.068
LFM-0507-05 5.0 7.0 11.0 5.0 1.0 7.000 7.015 4.970 5.000
LFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
LFM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
LFM-0608-08 6.0 8.0 12.0 8.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
LFM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
LFM-0608-15 6.0 8.0 12.0 15.0 1.0 8.000 8.015 5.970 6.000
LFM-0709-12 7.0 9.0 15.0 12.0 1.0 7.025 7.083 9.000 9.015 6.964 7.000
LFM-0810-02 8.0 10.0 15.0 2.7 1.0 10.000 10.015 7.964 8.000
LFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
LFM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
LFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
8.025 8.083
LFM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
LFM-0810-23 8.0 10.0 15.0 23.0 1.0 10.000 10.015 7.964 8.000
LFM-0810-30 8.0 10.0 15.0 30.0 1.0 10.000 10.015 7.964 8.000
LFM-081015-05 8.0 10.0 15.0 5.0 1.0 10.000 10.015 7.964 8.000
LFM-1012-04 10.0 12.0 18.0 4.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-06 10.0 12.0 18.0 6.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-09 10.0 12.0 18.0 9.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
LFM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
LFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
LFM-1214-04 12.0 14.0 20.0 4.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-06 12.0 14.0 20.0 6.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
LFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-10 12.0 14.0 20.0 10.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-11 12.0 14.0 20.0 11.0 1.0 14.000 14.018 11.957 12.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 175
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
LFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
LFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
LFM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
LFM-1315-06 13.0 15.0 22.0 6.0 1.0 13.032 13.102 15.000 15.018 12.957 13.000
LFM-1416-04 14.0 16.0 22.0 4.0 1.0 16.000 16.018 13.957 14.000
LFM-1416-05 14.0 16.0 22.0 5.0 1.0 16.000 16.018 13.957 14.000
LFM-1416-08 14.0 16.0 22.0 8.0 1.0 16.000 16.018 13.957 14.000
14.032 14.102
LFM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
LFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
LFM-1416-29 14.0 16.0 22.0 29.0 1.0 16.000 16.018 13.957 14.000
LFM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
LFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
15.022 15.102
LFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
LFM-1517-20 15.0 17.0 23.0 20.0 1.0 17.000 17.018 14.957 15.000
LFM-1618-09 16.0 18.0 24.0 9.0 1.0 18.000 18.018 15.957 16.000
LFM-1618-12 16.0 18.0 24.0 12.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
LFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
LFM-1719-12 17.0 19.0 25.0 12.0 1.0 19.000 19.021 16.957 17.000
LFM-1719-18 17.0 19.0 25.0 18.0 1.0 17.032 17.102 19.000 19.021 16.957 17.000
LFM-1719-25 17.0 19.0 25.0 25.0 1.0 19.000 19.021 16.957 17.000
LFM-1820-06 18.0 20.0 26.0 6.0 1.0 20.000 20.021 17.957 18.000
LFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
18.032 18.102
LFM-1820-17 18.0 20.0 26.0 17.0 1.0 20.000 20.021 17.957 18.000
LFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
LFM-2023-11 20.0 23.0 23.0 11.0 1.5 23.000 23.021 19.948 20.000
LFM-2023-14 20.0 23.0 30.0 14.5 1.5 23.000 23.021 19.948 20.000
20.040 20.124
LFM-2023-16 20.0 23.0 30.0 16.0 1.5 23.000 23.021 19.948 20.000
LFM-2023-21 20.0 23.0 30.0 21.0 1.5 23.000 23.021 19.948 20.000
LFM-2427-10 24.0 27.0 32.0 10.5 1.5 24.040 24.124 27.000 27.021 23.948 24.000
LFM-2528-11 25.0 28.0 35.0 11.0 1.5 28.000 28.021 24.948 25.000
LFM-2528-16 25.0 28.0 35.0 16.5 1.5 28.000 28.021 24.948 25.000
LFM-2528-21 25.0 28.0 35.0 21.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
LFM-2528-30 25.0 28.0 35.0 30.0 1.5 28.000 28.021 24.948 25.000
LFM-252831-13 25.0 28.0 31.0 13.0 1.5 28.000 28.021 24.948 25.000
LFM-2830-36 28.0 30.0 35.0 36.0 1.0 28.040 28.124 30.000 30.025 27.948 28.000
LFM-3034-10 30.0 34.0 42.0 10.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
30°
L F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 175
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
LFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
LFM-3034-26 30.0 34.0 42.0 26.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
LFM-3034-37 30.0 34.0 42.0 37.0 2.0 34.000 34.025 29.948 30.000
LFM-3236-16 32.0 36.0 40.0 16.0 2.0 36.000 36.025 31.938 32.000
32.050 32.150
LFM-3236-26 32.0 36.0 40.0 26.0 2.0 36.000 36.025 31.938 32.000
LFM-3539-09 35.0 39.0 47.0 9.0 2.0 39.000 39.025 34.938 35.000
LFM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.050 35.150
LFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
LFM-353950-35 35.0 39.0 50.0 35.0 2.0 39.000 39.025 34.938 35.000
LFM-3842-22 38.0 42.0 50.0 22.0 2.0 38.050 38.150 42.000 42.025 37.938 38.000
LFM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.050 40.150
LFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
LFM-4550-50 45.0 50.0 58.0 50.0 2.0 45.050 45.150 50.000 50.025 44.938 45.000
LFM-5055-40 50.0 55.0 63.0 40.0 2.0 55.000 55.030 49.938 50.000
50.050 50.150
LFM-5055-50 50.0 55.0 63.0 50.0 2.0 55.000 55.030 49.938 50.000
LFM-5560-60 55.0 60.0 68.0 60.0 2.0 55.060 55.180 60.000 60.030 54.926 55.000
LFM-5762-40 57.0 62.0 67.0 40.0 2.0 57.060 57.180 62.000 62.030 57.926 57.000
LFM-6065-60 60.0 65.0 73.0 60.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
LFM-6570-60 65.0 70.0 78.0 60.0 2.0 65.060 65.180 70.000 70.030 64.926 65.000
LFM-7075-100 70.0 75.0 83.0 100.0 2.0 70.060 70.180 75.000 75.030 69.926 70.000
LFM-7580-100 75.0 80.0 88.0 100.0 2.0 75.060 75.180 80.000 80.030 74.926 75.000
LFM-8085-100 80.0 85.0 93.0 100.0 2.5 80.060 80.180 85.000 85.035 79.926 80.000
LFM-9095-100 90.0 95.0 103.0 100.0 2.5 90.072 90.212 95.000 95.035 90.913 90.000
LFM-100105-100 100.0 105.0 113.0 100.0 2.5 100.072 100.212 105.000 105.035 99.913 100.000
LFM-120125-100 120.0 125.0 133.0 100.0 2.5 120.072 120.212 125.000 125.035 119.900 120.000
d1
Type Dimensions
S
Order key
d2 L T M -05 09- 006
d6
Thickness s (inch)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part Number d1 d2 s d4 d5 h d6
h
+0.25 -0.25 -0.05 -0.12 +0.375 +0.2 +0.12
+0.12 +0.125 -0.2
psi
iglide® T500
• Temperature resistant from -148°F to 482°F in
continuous operation
• Universal resistance to chemicals
• High compressive strength
• Very low moisture absorption
• Excellent wear resistance through the entire
temperature range
193
iglide®
T500 iglide® T500 - High-Tech Problem Solver
High temperature and chemical resistance
Temperature resistant
from -148°F to 482°F in iglide® T500 is defined by its combination of high temperature
continuous operation resistance with compressive strength, along with high
resistance to chemicals. iglide® T500 is designed for higher
speeds than other iglide® bearings.
Mechanical Properties
Modulus of elasticity psi 1,174,800 DIN 53457
Tensile strength at 68°F psi 24,660 DIN 53452
Compressive strength psi 14,500
Permissible static surface pressure (68°F) psi 21,760
Shore D-hardness 85 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 105 DIN IEC 93
Surface resistance Ω < 103 DIN 53482
Compressive Strength 8
+73 °F +140 °F
Deformation under load and temperature
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Permissible pv values for iglide® T500 running dry against a steel
shaft, at 68°F Rotating 295 689
Oscillating 216 492
Linear 984 1968
Temperatures
23,210
In terms of temperature resistance, iglide ® T500 has taken on a leading
20,310
position. Having a permissible long-term application temperature of 482°F,
17,400
iglide® T500 will even withstand 599°F for the short-term.
14,500
As in all thermoplastics, the compression resistance of T500 decreases with
11,600
increasED temperature. However, the wear drops considerably when used
Pressure (psi)
8,702
within the observed temperature range of 73°F to 302°F. In certain cases,
5,802
relaxation of the bearing can occur at temperatures greater than 275°F.
2,901
This could lead to the bearing moving out of the housing after re-cooling.
0
At temperatures over 275°F, the axial securing of the bearing in the housing
68 122 212 302 392 482
needs to be tested. If necessary, secondary measures must be taken to
mechanically secure the bearing. Please contact us if you have questions Temperature in °F
on bearing use.
Recommended maximum permissible static surface
➤ Application temperatures, Page 67 pressure of iglide® T500 as a result of temperature
0.4 0.25
C oef ficient of friction µ
0.20
0.15
C oef ficient of friction µ
0.3
0.10
0.05
0.2
0.00
0 1450 2900 4350 5800 7250 8700 10150 11600 13050
Pressure (psi)
0.1
9.84 19.69 29.53 39.37 49.22 59.05 68.90 Coefficient of friction for iglide® T500 as a result of the
Surface Speed (fpm ) load, v = 1.97 fpm
Coefficient of friction for iglide® T500 as a result of the
surface speed; p = 108 psi, 1050 hard chromed
Coefficient of friction µ
0.60
0.50
iglide® T500 Coefficient of Friction
0.40
Dry 0.09 - 0.27
0.30
Grease 0.09
0.20
Oil 0.04 4 16 28 40 52 63
Coefficient of friction for iglide® T500 against steel Coefficients of friction as a function of the shaft surface
(Shaft finish = 40 rms, 50 HRC) (1050 hard chromed)
180
Shaft Materials 160
The graphs show results of testing different shaft materials with plain 140
bearings made of iglide® T500. For low loads in rotating operation, the 120
best wear values are found with 303 Stainless and HR Carbon Steel 100
shafts. However, above a load of 290 psi, the bearing wear greatly 80
Wear (µm/km)
increases with these two shaft materials. For the higher load range, 60
hard-chromed shafts or Cold Rolled Steel shafts are advantageous. 40
In oscillating operation at low loads, similar wear values for cold rolled 20
steel and 303 stainless steel shafts occur. The wear is somewhat
0
higher than during rotational movements. 0 1 2 3 4 5
If the shaft material you plan to use is not contained in this list, please Pressure (psi)
contact us. 1050 Steel HR carbon steel 304 SS Hard chromed
➤ Shaft Materials, Page 71 Wear of iglide ® T500 with different shaft materials in
rotational operation
70
35.0 60
50
30.0
40
Hard anodized aluminum
25.0
Automatic screw steel
30
1050, hard chromed
20.0
Wear (µm/km)
HR Carbon Steel
20
15.0
304 Stainless
Wear (µm/km)
10
1050 Steel
10.0
0
440B
5.0
1050 Steel Hard chromed 304 Stainless
0.0
Rotating Oscillating
Wear of iglide® T500 with different shaft materials, Wear for oscillating and rotating applications with
p = 108 psi, v = 98 fpm different shaft materials p = 290 psi
Chemical Resistance
0.02
0.00
0.0 0.1 0.2 0.3 0.4 0.5
Medium Resistance
M oistur e absorption (weight %)
Alcohol +
Hydrocarbon + Effect of moisture absorption on iglide® T500 plain
Greases, oils without additives + bearings
Fuels +
Weak acids +
Strong acids –
Weak alkaline +
Strong alkaline +
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Plain bearings made from iglide® T500 are resistant to radiation up to an intensity of 1x105 Gy. iglide® T500 is the most radioactive-
resistant material of the iglide® product line. iglide® T500 is extremely resistant to hard gamma radiation and withstands a radiation
dose of 1000 Mrad without detectable change in its properties. The material also withstands an alpha or beta radiation of 10,000
Mrad with practically no damage.
UV Resistance
The excellent material properties of iglide® T500 do not change under UV radiation and other weathering effects.
Vacuum
In a vacuum environment, iglide ® T500 plain bearings can be used virtually without restrictions. Outgassing takes place to a very
limited extent.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 197
Inch
*Based on steel housing bore
TFI-0203-03 1/8 3/16 3/16 .312 .032 .1873 .1878 .1236 .1243
.1251 .1269
TFI-0203-06 1/8 3/16 3/8 .312 .032 .1873 .1878 .1236 .1243
TFI-0304-04 3/16 1/4 1/4 .375 .032 .2497 .2503 .1858 .1865
TFI-0304-06 3/16 1/4 3/8 .375 .032 .1873 .1892 .2497 .2503 .1858 .1865
TFI-0304-08 3/16 1/4 1/2 .375 .032 .2497 .2503 .1858 .1865
TFI-0405-03 1/4 5/16 3/16 .500 .032 .3122 .3128 .2481 .2490
TFI-0405-04 1/4 5/16 1/4 .500 .032 .3122 .3128 .2481 .2490
TFI-0405-06 1/4 5/16 3/8 .500 .032 .2498 .2521 .3122 .3128 .2481 .2490
TFI-0405-08 1/4 5/16 1/2 .500 .032 .3122 .3128 .2481 .2490
TFI-0405-12 1/4 5/16 3/4 .500 .032 .3122 .3128 .2481 .2490
TFI-0506-04 5/16 3/8 1/4 .562 .032 .3747 .3753 .3106 .3115
TFI-0506-06 5/16 3/8 3/8 .562 .032 .3125 .3148 .3747 .3753 .3106 .3115
TFI-0506-08 5/16 3/8 1/2 .562 .032 .3747 .3753 .3106 .3115
TFI-0607-04 3/8 15/32 1/4 .687 .046 .4684 .4691 .3731 .3740
TFI-0607-06 3/8 15/32 3/8 .687 .046 .4684 .4691 .3731 .3740
.3750 .3773
TFI-0607-08 3/8 15/32 1/2 .687 .046 .4684 .4691 .3731 .3740
TFI-0607-12 3/8 15/32 3/4 .687 .046 .4684 .4691 .3731 .3740
TFI-0708-08 7/16 17/32 1/2 .750 .046 .4379 .4406 .5309 .5316 .4355 .4365
TFI-0809-04 1/2 19/32 1/4 .875 .046 .5934 .5941 .4980 .4990
TFI-0809-06 1/2 19/32 3/8 .875 .046 .5934 .5941 .4980 .4990
TFI-0809-08 1/2 19/32 1/2 .875 .046 .5003 .5030 .5934 .5941 .4980 .4990
TFI-0809-12 1/2 19/32 3/4 .875 .046 .5934 .5941 .4980 .4990
TFI-0809-16 1/2 19/32 1 .875 .046 .5934 .5941 .4980 .4990
TFI-1011-08 5/8 23/32 1/2 .937 .046 .7184 .7192 .6230 .6240
TFI-1011-12 5/8 23/32 3/4 .937 .046 .7184 .7192 .6230 .6240
.6253 .6280
TFI-1011-16 5/8 23/32 1 .937 .046 .7184 .7192 .6230 .6240
TFI-1011-24 5/8 23/32 1 1/2 .937 .046 .7184 .7192 .6230 .6240
TFI-1214-08 3/4 7/8 1/2 1.125 .062 .8747 .8755 .7479 .7491
TFI-1214-12 3/4 7/8 3/4 1.125 .062 .8747 .8755 .7479 .7491
.7507 .7541
TFI-1214-16 3/4 7/8 1 1.125 .062 .8747 .8755 .7479 .7491
TFI-1214-28 3/4 7/8 1 3/4 1.125 .062 .8747 .8755 .7479 .7491
TFI-1416-12 7/8 1 3/4 1.250 .062 .9997 1.0005 .8729 .8741
.8757 .8791
TFI-1416-16 7/8 1 1 1.250 .062 .9997 1.0005 .8729 .8741
TFI-1618-08 1 1 1/8 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
TFI-1618-12 1 1 1/8 3/4 1.375 .062 1.1247 1.1255 .9979 .9991
1.0007 1.0041
TFI-1618-16 1 1 1/8 1 1.375 .062 1.1247 1.1255 .9979 .9991
TFI-1618-24 1 1 1/8 1 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 197
Inch
*Based on steel housing bore
TFI-1719-06 1 1/16 1 3/16 3/8 1.500 .062 1.0633 1.0666 1.1875 1.1883 1.0604 1.0616
TFI-1820-12 1 1/8 1 9/32 3/4 1.562 .078 1.1254 1.1288 1.2808 1.2818 1.1226 1.1238
TFI-2022-20 1 1/4 1 13/32 1 1/4 1.687 .078 1.4058 1.4068 1.2472 1.2488
1.2508 1.2548
TFI-2022-32 1 1/4 1 13/32 2 1.687 .078 1.4058 1.4068 1.2472 1.2488
TFI-2426-12 1 1/2 1 21/32 3/4 2.000 .078 1.6558 1.6568 1.4972 1.4988
TFI-2426-16 1 1/2 1 21/32 1 2.000 .078 1.5008 1.5048 1.6558 1.6568 1.4972 1.4988
TFI-2426-24 1 1/2 1 21/32 1 1/2 2.000 .078 1.6558 1.6568 1.4972 1.4988
TFI-2831-16 1 3/4 1 15/16 1 2.375 .093 1.7507 1.7547 1.9371 1.9381 1.7471 1.7487
TFI-3235-32 2 2 3/16 2 2.625 .093 2.0011 2.0057 2.1871 2.1883 1.9969 1.9981
TFI-4447-32 2 3/4 2 15/16 2 3.375 .093 2.7523 2.7570 2.9358 2.9370 2.7490 2.7500
d1
Type Dimensions
S
Order key
d2 T T I -06 20- 015
d6
Thickness s (inch)
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
Form T (washer)
iglide® material
h
d5
d4
Inch
d6
Part Number d1 d2 s d4 d5 h d6
h
+.010 -.010 -.0020 +-.005 +.015 +.005 +.008 +.005
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
TSM-0203-03 2.0 3.5 3.0 2.006 2.046 3.500 3.580 1.975 2.000
TSM-0304-03 3.0 4.5 3.0 4.500 4.512 2.975 3.000
3.006 3.046
TSM-0304-06 3.0 4.5 6.0 4.500 4.512 2.975 3.000
TSM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
TSM-0405-06 4.0 5.5 6.0 4.010 4.058 5.500 5.512 3.970 4.000
TSM-0405-10 4.0 5.5 10.0 5.500 5.512 3.970 4.000
TSM-0507-035 5.0 7.0 3.5 7.000 7.015 4.970 5.000
TSM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
5.010 5.058
TSM-0507-08 5.0 7.0 8.0 7.000 7.015 4.970 5.000
TSM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
TSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
TSM-0608-08 6.0 8.0 8.0 8.000 8.015 5.970 6.000
6.010 6.058
TSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
TSM-0608-13 6.0 8.0 13.0 8.000 8.015 5.970 6.000
TSM-0610-08 6.0 10.0 8.0 10.000 10.015 5.970 6.000
6.010 6.058
TSM-0610-20 6.0 10.0 20.0 10.000 10.015 5.970 6.000
TSM-0709-10 7.0 9.0 10.0 9.000 9.015 6.964 7.000
7.013 7.071
TSM-0709-12 7.0 9.0 12.0 9.000 9.015 6.964 7.000
TSM-0810-06 8.0 10.0 6.0 10.000 10.015 7.984 8.000
TSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
TSM-0810-10 8.0 10.0 10.0 8.013 8.071 10.000 10.015 7.964 8.000
TSM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
TSM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
TSM-1012-035 10.0 12.0 3.5 12.000 12.018 9.964 10.000
TSM-1012-06 10.0 12.0 6.0 12.000 12.018 9.964 10.000
TSM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
TSM-1012-10 10.0 12.0 10.0 10.013 10.071 12.000 12.018 9.964 10.000
TSM-1012-12 10.0 12.0 12.0 12.000 12.018 9.964 10.000
TSM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
TSM-1012-20 10.0 12.0 20.0 12.000 12.018 9.964 10.000
TSM-1214-035 12.0 14.0 3.5 14.000 14.018 11.957 12.000
TSM-1214-06 12.0 14.0 6.0 14.000 14.018 11.957 12.000
TSM-1214-08 12.0 14.0 8.0 14.000 14.018 11.957 12.000
TSM-1214-10 12.0 14.0 10.0 12.016 12.086 14.000 14.018 11.957 12.000
TSM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
TSM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
TSM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
TSM-4550-50 45.0 50.0 50.0 45.025 45.125 50.000 50.025 44.938 45.000
TSM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
TSM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
TSM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000
TSM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
TSM-5055-60 50.0 55.0 60.0 55.000 55.030 49.938 50.000
TSM-5560-50 55.0 60.0 50.0 55.030 55.150 60.000 60.030 54.926 55.000
TSM-6065-45 60.0 65.0 45.0 65.000 65.030 59.926 60.000
60.030 60.150
TSM-6065-60 60.0 65.0 60.0 65.000 65.030 59.926 60.000
TSM-6570-50 65.0 70.0 50.0 65.030 65.150 70.000 70.030 64.926 65.000
TSM-7075-70 70.0 75.0 70.0 70.030 70.150 75.000 75.030 69.926 70.000
30°
T F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 197
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
TFM-020406-03 2.0 4.0 6.0 3.0 1.0 2.006 2.046 4.000 4.012 1.975 2.000
TFM-0304-05 3.0 4.5 7.5 5.0 0.75 3.006 3.046 4.500 4.512 2.975 3.000
TFM-0405-04 4.0 5.5 9.5 4.0 0.75 5.500 5.512 3.970 4.000
TFM-0405-06 4.0 5.5 9.5 6.0 0.75 4.010 4.058 5.500 5.512 3.970 4.000
TFM-040508-06 4.0 5.5 8.0 6.0 0.75 5.500 5.512 3.970 4.000
TFM-0507-05 5.0 7.0 11.0 5.0 1.0 5.010 5.058 7.000 7.015 4.970 5.000
TFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
TFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
TFM-0608-10 6.0 8.0 12.0 10.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
TFM-060812-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
TFM-060812-20 6.0 8.0 12.0 20.0 1.0 8.000 8.015 5.970 6.000
TFM-081012-04 8.0 10.0 12.0 4.0 1.0 10.000 10.015 7.964 8.000
TFM-0810-05 8.0 10.0 15.0 5.0 1.0 10.000 10.015 7.964 8.000
TFM-0810-075 8.0 10.0 15.0 7.5 1.0 8.013 8.071 10.000 10.015 7.964 8.000
TFM-0810-08 8.0 10.0 15.0 8.0 1.0 10.000 10.015 7.964 8.000
TFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
TFM-081117-05 8.0 11.0 17.0 5.0 1.5 8.013 8.071 11.000 11.015 7.964 8.000
TFM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-06 10.0 12.0 18.0 6.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-08 10.0 12.0 15.0 8.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
10.013 10.071
TFM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-18 10.0 12.0 18.0 18.0 1.0 12.000 12.018 9.964 10.000
TFM-1012-22 10.0 12.0 18.0 22.0 1.0 12.000 12.018 9.964 10.000
TFM-1214-05 12.0 14.0 20.0 5.5 1.0 14.000 14.018 11.957 12.000
TFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
TFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
TFM-1214-15 12.0 14.0 20.0 15.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
TFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
TFM-121418-039 12.0 14.0 18.0 3.9 1.0 14.000 14.018 11.957 12.000
TFM-121418-059 12.0 14.0 18.0 5.9 1.0 14.000 14.018 11.957 12.000
TFM-1416-10 14.0 16.0 22.0 10.0 1.0 16.000 16.018 13.957 14.000
TFM-1416-12 14.0 16.0 22.0 12.0 1.0 14.016 14.086 16.000 16.018 13.957 14.000
TFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 197
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
TFM-1517-06 15.0 17.0 23.0 6.0 1.0 17.000 17.018 14.957 15.000
TFM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
15.016 15.086
TFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
TFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
TFM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
TFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
TFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
TFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
TFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
TFM-2023-065 20.0 23.0 30.0 6.5 1.5 23.000 23.021 19.948 20.000
TFM-2023-075 20.0 23.0 30.0 7.5 1.5 23.000 23.021 19.948 20.000
TFM-2023-11 20.0 23.0 30.0 11.5 1.5 20.020 20.104 23.000 23.021 19.948 20.000
TFM-2023-16 20.0 23.0 30.0 16.0 1.5 23.000 23.021 19.948 20.000
TFM-2023-21 20.0 23.0 30.0 21.0 1.5 23.000 23.021 19.948 20.000
TFM-252833-08 25.0 28.0 33.0 8.0 1.5 28.000 28.021 24.948 25.000
TFM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
TFM-2528-13 25.0 28.0 35.0 13.5 1.5 25.020 25.104 28.000 28.021 24.948 25.000
TFM-2528-16 25.0 28.0 35.0 16.5 1.5 28.000 28.021 24.948 25.000
TFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
TFM-2730-20 27.0 30.0 38.0 20.0 1.5 27.020 27.104 30.000 30.021 26.948 27.000
TFM-2834-44 28.0 34.0 42.0 44.0 2.0 28.020 28.104 34.000 34.021 27.948 28.000
TFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
TFM-3034-26 30.0 34.0 42.0 26.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000
TFM-3034-40 30.0 34.0 42.0 40.0 2.0 34.000 34.025 29.948 30.000
TFM-3236-15 32.0 36.0 45.0 15.0 2.0 36.000 36.025 31.938 32.000
32.025 32.125
TFM-3236-26 32.0 36.0 45.0 26.0 2.0 36.000 36.025 31.938 32.000
TFM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.025 35.125
TFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
TFM-4044-22 40.0 44.0 52.0 22.0 2.0 44.000 44.025 39.938 40.000
TFM-4044-30 40.0 44.0 52.0 30.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
TFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
TFM-4550-50 45.0 50.0 58.0 50.0 2.0 45.025 45.125 50.000 50.025 44.938 45.000
TFM-5055-40 50.0 55.0 63.0 40.0 2.0 50.025 50.125 55.000 55.030 49.938 50.000
TFM-6065-40 60.0 65.0 73.0 40.0 2.0 60.030 60.150 65.000 65.030 59.926 60.000
TFM-7075-40 70.0 75.0 83.0 40.0 2.0 70.030 70.150 75.000 75.030 69.926 70.000
TFM-7580-50 75.0 80.0 88.0 50.0 2.0 75.030 75.150 80.000 80.030 74.926 75.000
iglide®
T500 iglide® T500 - Product Range
Thrust washer - Metric d4
d5
d1
Type Dimensions
S
Order key
d2 T T M -06 20- 015
d6
Thickness s (mm)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part Number d1 d2 s d4 d5 h d6
h
+0.25 -0.25 -0.05 -0.12 +0.375 +0.2 +0.12
+0.12 +0.125 -0.2
max. +338 °F
min. –40 °F
4 materials
Ø 1/4 to 2 inches
more dimensions on request
Ø 3 to 95 mm
mm
more dimensions on request
iglide® plastic bearings are a practical and low priced alternative to An external load system for helicopters required a low weight, high
bronze, metallic, rolled and injection-molded plain bearings in this reliability with simultaneous weather resistance and freedom from
boat lift application. maintenance.
Thanks to the excellent mechanical and gliding properties of the The self-lubricating iglide® bearings are used, among other things,
bearings, the maintenance-free and lubrication free mechanical to eliminate the potential of contamination by external lubricants.
hand can be moved by hand.
The special feature here is the economical plastic bearings, which Thanks to the noise-dampening properties of the plastic bearings,
serve as rear axle bearing in the housing and allows the sensors to they contribute to a much quieter operation.
last considerably longer.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® P l l l l
iglide® P210 l l l l
iglide® K l l l
iglide® GLW l
Low water For under Edge Vibrations Food Temperatures Temperatures Economical
absorption water use pressure dampening suitable up to up to
+212°F +302°F
iglide® P l l
iglide® P210 l l l l
iglide® K l l l l
iglide® GLW l l
iglide® P 217
iglide® K 241
iglide® P 3 1 217
iglide® K 3 3 241
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
217
iglide®
P iglide® P - Low water absorption
Cost-effective
Mechanical Properties
Modulus of elasticity psi 768,700 DIN 53457
Tensile strength at 68°F psi 17,400 DIN 53452
Compressive strength psi 9,572
Permissible static surface pressure (68°F) psi 7,252
Shore D-hardness 75 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 10
9
The graph shows the elastic deformation of iglide® P for radial loads. 8
4
➤ Compressive strength, Page 63 3
2
1
0
0 725 1450 2176 2901 3626 4351 5076 5802 6527 7252
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
Plain bearings made from iglide® P are maintenance-free plain bearings,
which were developed for low to average surface speeds.
The maximum values given in the table can only be achieved at a very
1,450
low surface pressure. The maximum speed given is the speed at which
an increase up to the continuous use temperature occurs due to friction.
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures
8702
Pressure (psi)
plain bearings decreases.
The ambient temperatures in the bearing system also have an effect on 1450
the bearing wear. With increasing temperatures, the wear increases.
0
68 86 104 122 140 158 176 194 212 230 248 266
➤ Application temperatures, Page 67
Temperature (°F)
0.4
0.15
0.10
Coefficient of friction (µ)
0.3
0.05
0.2 0.00
0 725 1450 2175 2900 3625 4350 5075
Pressure (psi)
0.30
iglide® P Coefficient of Friction
Dry 0.06 - 0.21 0.25
Shaft Materials
The graphs show results of testing different shaft materials with plain 180
For rotating movements, the wear of iglide® P with Cold Rolled Steel 140
120
and HR Carbon Steel shafts is very low. On the other hand, the bear-
100
ings on 303 Stainless Steel shafts as well as hard-chromed shafts re-
80
sult in higher wear than other shaft materials even in the low load range.
Wear (µm/km)
60
For example at a load of 290 psi, Cold Rolled Steel is six times better
40
than 303 Stainless Steel.
20
For oscillating movements without loads, wear rates are lower than for
0
most rotating movements. For this purpose, the Cold Rolled Steel and 0 1450 2901 4351 5802 7252
hard-chromed shafts prove to be the best sliding partners. Also, the Pressure (psi)
303 Stainless Steel shafts that have poor results for rotation, are very
Rotating Oscillating
good in oscillating operation.
If the shaft material you plan to use is not contained in this list, please
contact us.
25
18
20
16
15
14
Hard anodized aluminum
Wear (µm/km)
12 10
Automatic screw steel
10 5
HR Carbon Steel
8
304 Stainless
0
Wear (µm/km)
6
1050 Steel
2
1050 Steel 304 SS
0
HR carbon steel Hard chromed
Wear of iglide® P with different shaft Wear of iglide ® P with different shaft materials in
materials in rotating applications, p=108 psi, rotating applications
v=98 fpm
G300.
0.02
Radiation Resistance
Plain bearings made of iglide® P have limited use under radioactive radiation.
They are resistant to radiation up to an intensity of 5 x 102 Gy.
UV-Resistance
iglide® P plain bearings are partially UV resistance.
Vacuum
In a vacuum environment, existing moisture of iglide® P plain bearings is released as a vapor. Use in a vacuum is only possible in a
limited manner.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 221
Inch
*Based on steel housing bore
PFI-0405-04 1/4 5/16 1/4 .500 .032 .3122 .3128 .2481 .2490
PFI-0405-05 1/4 5/16 5/16 .500 .032 .3122 .3128 .2481 .2490
PFI-0405-06 1/4 5/16 3/8 .500 .032 .2498 .2521 .3122 .3128 .2481 .2490
PFI-0405-08 1/4 5/16 1/2 .500 .032 .3122 .3128 .2481 .2490
PFI-0405-12 1/4 5/16 3/4 .500 .032 .3122 .3128 .2481 .2490
PFI-0506-04 5/16 3/8 1/4 .562 .032 .3747 .3753 .3106 .3115
PFI-0506-06 5/16 3/8 3/8 .562 .032 .3747 .3753 .3106 .3115
.3125 .3148
PFI-0506-08 5/16 3/8 1/2 .562 .032 .3747 .3753 .3106 .3115
PFI-0506-12 5/16 3/8 3/4 .562 .032 .3747 .3753 .3106 .3115
PFI-0607-04 3/8 15/32 1/4 .687 .046 .4684 .4691 .3731 .3740
PFI-0607-06 3/8 15/32 3/8 .687 .046 .4684 .4691 .3731 .3740
.3750 .3773
PFI-0607-08 3/8 15/32 1/2 .687 .046 .4684 .4691 .3731 .3740
PFI-0607-12 3/8 15/32 3/4 .687 .046 .4684 .4691 .3731 .3740
PFI-0809-06 1/2 19/32 3/8 .875 .046 .5934 .5941 .4980 .4990
PFI-0809-08 1/2 19/32 1/2 .875 .046 .5934 .5941 .4980 .4990
PFI-0809-10 1/2 19/32 5/8 .875 .046 .5003 .5030 .5934 .5941 .4980 .4990
PFI-0809-12 1/2 19/32 3/4 .875 .046 .5934 .5941 .4980 .4990
PFI-0809-16 1/2 19/32 1 .875 .046 .5934 .5941 .4980 .4990
PFI-0810-10 1/2 5/8 5/8 .875 .062 .5013 .5040 .6250 .6257 .4983 .5000
PFI-1011-06 5/8 23/32 3/8 .937 .046 .7184 .7192 .6230 .6240
PFI-1011-08 5/8 23/32 1/2 .937 .046 .7184 .7192 .6230 .6240
.6253 .6280
PFI-1011-12 5/8 23/32 3/4 .937 .046 .7184 .7192 .6230 .6240
PFI-1011-16 5/8 23/32 1 .937 .046 .7184 .7192 .6230 .6240
PFI-1214-08 3/4 7/8 1/2 1.125 .062 .8747 .8755 .7479 .7491
PFI-1214-12 3/4 7/8 3/4 1.125 .062 .7507 .7541 .8747 .8755 .7479 .7491
PFI-1214-16 3/4 7/8 1 1.125 .062 .8747 .8755 .7479 .7491
PFI-1416-08 7/8 1 1/2 1.250 .062 .9997 1.0005 .8729 .8741
PFI-1416-12 7/8 1 3/4 1.250 .062 .8757 .8791 .9997 1.0005 .8729 .8741
PFI-1416-16 7/8 1 1 1.250 .062 .9997 1.0005 .8729 .8741
PFI-1618-08 1 1 1/8 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
PFI-1618-12 1 1 1/8 3/4 1.375 .062 1.1247 1.1255 .9979 .9991
1.0007 1.0041
PFI-1618-16 1 1 1/8 1 1.375 .062 1.1247 1.1255 .9979 .9991
PFI-1618-24 1 1 1/8 1 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
PFI-2224-16 1 3/8 1 1/2 1 1.875 .078 1.3758 1.3798 1.5308 1.5318 1.3722 1.3738
PFI-2426-20 1 1/2 1 21/32 1 1/4 2.000 .078 1.6558 1.6568 1.4972 1.4988
1.5008 1.5408
PFI-2426-24 1 1/2 1 21/32 1 1/2 2.000 .078 1.6558 1.6568 1.4972 1.4988
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 221
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
PFM-0405-04 4.0 5.5 9.5 4.0 0.75 4.020 4.068 5.500 5.512 3.970 4.000
PFM-0507-05 5.0 7.0 11.0 5.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
PFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
6.020 6.068
PFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
PFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
PFM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
PFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
8.025 8.083
PFM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
PFM-081012-10 8.0 10.0 12.0 10.0 1.0 10.000 10.015 7.964 8.000
PFM-0810-15 8.0 10.0 15.0 15.0 1.0 10.000 10.015 9.964 10.000
PFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
PFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
10.025 10.083
PFM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
PFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
PFM-121418-08 12.0 14.0 18.0 8.0 1.0 14.000 14.018 11.957 12.000
PFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
PFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
PFM-1214-10 12.0 14.0 20.0 10.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
PFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
PFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
PFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
PFM-1416-08 14.0 16.0 22.0 8.0 1.0 16.000 16.018 13.957 14.000
PFM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.032 14.102
PFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
PFM-141624-25 14.0 16.0 24.0 25.0 1.0 16.000 16.018 13.957 14.000
PFM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
PFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
15.032 15.102
PFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
PFM-1517-22 15.0 17.0 23.0 22.0 1.0 17.000 17.018 14.957 15.000
PFM-151824-32 15.0 18.0 24.0 32.0 1.5 15.032 15.102 18.000 18.018 14.957 15.000
PFM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
PFM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
PFM-161824-40 16.0 18.0 24.0 40.0 1.0 18.000 18.018 15.957 16.000
PFM-1719-25 17.0 19.0 25.0 25.0 1.0 17.032 17.102 19.000 19.021 16.957 17.000
PFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
PFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
PFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
30°
P F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 221
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
PFM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
PFM-2023-16 20.0 23.0 30.0 16.5 1.5 23.000 23.021 19.948 20.000
PFM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
PFM-2023-30 20.0 23.0 30.0 30.0 1.5 23.000 23.021 19.948 20.000
PFM-202328-15 20.0 23.0 28.0 15.0 1.5 23.000 23.021 19.948 20.000
PFM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
PFM-2528-16 25.0 28.0 35.0 16.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
PFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
PFM-283239-20 28.0 32.0 39.0 20.0 2.0 28.040 28.124 32.000 32.025 28.948 28.000
PFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
PFM-3034-26 30.0 34.0 42.0 26.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
PFM-3034-37 30.0 34.0 42.0 37.0 2.0 34.000 34.025 29.948 30.000
PFM-3236-16 32.0 36.0 40.0 16.0 2.0 32.050 32.150 36.000 36.025 31.938 32.0000
PFM-3539-058 35.0 39.0 47.0 5.8 2.0 39.000 39.025 34.938 35.000
PFM-3539-16 35.0 39.0 47.0 16.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
PFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
PFM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.050 40.150
PFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
PFM-4550-50 45.0 50.0 58.0 50.0 2.5 45.050 45.150 50.000 50.025 44.938 45.000
PFM-5055-60 50.0 55.0 63.0 60.0 2.0 50.050 50.150 55.000 55.030 49.938 50.000
PFM-6065-50 60.0 65.0 73.0 50.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
PFM-7075-50 70.0 75.0 83.0 50.0 2.0 70.060 70.180 75.000 75.030 69.926 70.000
PFM-8085-100 80.0 85.0 93.0 100.0 2.5 80.060 80.180 85.000 85.030 79.926 80.000
231
iglide®
P210 iglide® P210 - Extremely wear resistant
Flexible, wear resistant in pivoting motions and more
Versatile: good with l When you need a universal bearing for use in a moist
many different shafts environment
l When you need a wear-resistant bearing for pivoting
applications at medium loads
l When edge loads and shocks occur
l When the surface pressure of iglide® J is insufficient
Good with edge loads
Mechanical Properties
Modulus of elasticity psi 362,600 DIN 53457
Tensile strength at 68°F psi 10,150 DIN 53452
Compressive strength psi 7,252
Permissible static surface pressure (68°F) psi 7,252
Shore D-hardness 75 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 10
9
The graph shows the elastic deformation of iglide® P210 as a function 8
of radial pressure. At the recommended maximum surface pressure 7
6
of 7,252 psi, the deformation is less than 3% at room temperature.
5
Deformation (%)
4
➤ Compressive strength, Page 63 3
2
1
0
0 3,626 7,252 10,880
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
Plain bearings made from iglide ® P210 are maintenance-free plain
bearings, which were developed for low to average surface speeds.
The maximum values given in the table can only be achieved at a very
1,450
low surface pressure. The maximum speed given is the speed at which
an increase up to the continuous use temperature occurs due to friction.
145
➤ Surface speed, Page 64
➤ pv value, Page 65
Pressure (psi)
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures 8702
7252
Even at its highest long-term application temperature of 212°F, iglide®
P210 is suitable for a large application spectrum. If higher temperatures 5802
are required, iglide® G300, with a maximum long-term temperature of
4351
266°F can be used. The ambient temperatures in the bearing system
also have an effect on the bearing wear. With increasing temperatures, 2901
Pressure (psi)
the wear increases. 1450
0
➤ Application temperatures, Page 67
68 86 104 122 140 158 176 194 212
Temperature (°F)
0.40 0.30
0.35
0.25
0.30
Coefficient of friction (µ)
0.25 0.20
0.20 0.15
0.15
0.10
0.10
0.05 0.05
0.00 0.00
19.69 29.53 39.37 49.21 59.06 68.90 78.74 0 1,450 2,901 4,351 5,802 7,252
Surface Speed (fpm) Pressure (psi)
Coefficients of friction of iglide® P210 as a result of Coefficients of friction of iglide® P210 as a result of
the surface speed; p = 145 psi the load, v = 1.97 fpm
Shaft Materials
120
The graphs show results of testing different shaft materials with plain
bearings made of iglide® P210. 100
For rotating movements at radial loads below 145 psi, iglide® P210 has
80
generally very low wear. Wear is only significantly higher in combination
with carbon steel shafts. Generally, rotational wear will be higher than 60
for a pivoting application of equal load. This is only reversed at loads
Wear (µm/km)
40
above 3,626 psi.
20
➤ Shaft Materials, Page 71
0
0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
Pressure (psi)
Rotating Oscillating
3
1050, hard chromed
HR Carbon Steel
2
304 Stainless
Wear (µm/km)
1050 Steel
1
440B
Chemical Resistance
Radiation Resistance
Plain bearings made of iglide® P210 have limited use under radioactive radiation.
They are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® P210 plain bearings have a good resistance to UV radiation..
Vacuum
In a vacuum environment, existing moisture of iglide® P210 plain bearings is released as a vapor. Use in a vacuum is limited.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
P210SM-2023-30 20.0 23.0 30.0 20.040 20.124 23.000 23.021 19.948 20.000
P210SM-2225-15 22.0 25.0 15.0 25.000 25.021 21.948 22.000
P210SM-2225-20 22.0 25.0 20.0 25.000 25.021 21.948 22.000
22.040 22.124
P210SM-2225-25 22.0 25.0 25.0 25.000 25.021 21.948 22.000
P210SM-2225-30 22.0 25.0 30.0 25.000 25.021 21.948 22.000
P210SM-2427-15 24.0 27.0 15.0 27.000 27.021 23.948 24.000
P210SM-2427-20 24.0 27.0 20.0 27.000 27.021 23.948 24.000
24.040 24.124
P210SM-2427-25 24.0 27.0 25.0 27.000 27.021 23.948 24.000
P210SM-2427-30 24.0 27.0 30.0 27.000 27.021 23.948 24.000
P210SM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
P210SM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000
25.040 25.124
P210SM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
P210SM-2528-30 25.0 28.0 30.0 28.000 28.021 24.948 25.000
P210SM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
P210SM-2832-25 28.0 32.0 25.0 28.040 28.124 32.000 32.025 27.948 28.000
P210SM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
P210SM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
P210SM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
30.040 30.124
P210SM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000
P210SM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
P210SM-3236-20 32.0 36.0 20.0 36.000 36.025 31.938 32.000
P210SM-3236-30 32.0 36.0 30.0 32.050 32.150 36.000 36.025 31.938 32.000
P210SM-3236-40 32.0 36.0 40.0 36.000 36.025 31.938 32.000
P210SM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
P210SM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.050 35.150
P210SM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
P210SM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
P210SM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
P210SM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.050 40.150
P210SM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
P210SM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
P210SM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
P210SM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.050 45.150
P210SM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
P210SM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
P210SM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
50.050 50.150
P210SM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
P210 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
P210FM-0608-04 6.0 8.0 12.0 4.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
P210FM-0608-08 6.0 8.0 12.0 8.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
P210FM-0810-05 8.0 10.0 15.0 5.5 1.0 8.025 8.083 10.000 10.015 7.964 8.000
P210FM-0810-07 8.0 10.0 15.0 7.5 1.0 8.025 8.083 10.000 10.015 7.964 8.000
P210FM-0810-09 8.0 10.0 15.0 9.5 1.0 8.025 8.083 10.000 10.015 7.964 8.000
P210FM-1012-07 10.0 12.0 18.0 7.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
P210FM-1012-09 10.0 12.0 18.0 9.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
P210FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
P210FM-1012-12 10.0 12.0 18.0 12.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
P210FM-1012-17 10.0 12.0 18.0 17.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
P210FM-1214-07 12.0 14.0 20.0 7.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
P210FM-1214-09 12.0 14.0 20.0 9.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
P210FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
P210FM-1214-17 12.0 14.0 20.0 17.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
P210FM-1416-12 14.0 16.0 22.0 12.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
P210FM-1416-17 14.0 16.0 22.0 17.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
P210FM-1517-09 15.0 17.0 23.0 9.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
P210FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
P210FM-1517-17 15.0 17.0 23.0 17.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
P210FM-1618-12 16.0 18.0 24.0 12.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
P210FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
P210FM-1820-12 18.0 20.0 26.0 12.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
P210FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
P210FM-1820-22 18.0 20.0 26.0 22.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
P210FM-2023-11 20.0 23.0 30.0 11.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
P210FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
P210FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
P210FM-2528-11 25.0 28.0 35.0 11.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
P210FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
P210FM-2528-21 25.0 28.0 35.0 21.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
P210FM-3034-16 30.0 34.0 42.0 16.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
P210FM-3034-26 30.0 34.0 42.0 26.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
P210FM-3539-16 35.0 39.0 47.0 16.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
P210FM-3539-26 35.0 39.0 47.0 26.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
P210FM-4044-30 40.0 44.0 52.0 30.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
P210FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
P210FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.050 45.150 50.000 50.025 44.938 45.000
241
iglide®
K iglide® K - Low-cost for medium temperatures
Versatile
Cost-effective
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 507,600 DIN 53457
Tensile strength at 68°F psi 11,600 DIN 53452
Compressive strength psi 8,702
Permissible static surface pressure (68°F) psi 7,205
Shore D-hardness 72 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
2.0
0.0
0 725 1450 2176 2901 3626 4351 5076 5802 6527 7252 7977 8702
Pressure (psi)
140°F 73°F
Temperatures 11,600
Pressure (psi)
is significant when temperatures rise over 212°F.
2,901
Temperature (°F)
0.30 0.25
0.25
Coefficient of friction (µ)
0.20
0.20
0.15
0.15
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 2901 5802 8702
8
Shaft Materials
7
HR Carbon Steel
4
hard-chromed shafts are unsuitable. It is important to notice that with
304 Stainless
increasing loads, the recommended hardness of the shaft increases. 3
Wear (µm/km)
1050 Steel
Soft shafts tend to wear more easily and thus increase the wear of the 2
overall system, if the loads exceed 290 psi.
440B
1
The comparison of rotational movements to oscillating movements
shows that the wear is almost identical at a pressure up to 725 psi. 0
The higher the loads the greater the difference. Wear of iglide® K, rotating applications with different
shaft materials, p = 145 psi, v= 59 fpm
➤ Shaft Materials, Page 71
20
45
40
15
35
30
25 10
20
Wear (µm/km)
Wear (µm/km)
15 5
10
5
0
0 0 145 290 435 580 725
0 1450 2901 4351 5802 7252 8702
Pressure (psi)
Pressure (psi)
1050 Steel 304 SS
Rotating Oscillating
HR carbon steel Hard chromed
Wear with different shaft materials, oscillating and Wear of iglide ® K with different shaft materials in
rotating movement p = 290 psi rotational applications
Chemical Resistance
0.15
iglide® K plain bearings are resistant to diluted alkalis and very weak
acids, as well as fuels and a wide variety of lubricants. The low moisture
absorption also permits use in wet or damp environments.
0.00
0.0 0.2 0.4 0.6
Radiation Resistance
Plain bearings made from iglide® K are radiation resistant up to an intensity of 5 x 102 Gy.
UV-Resistance
iglide® K plain bearings become discolored under UV radiation. However, hardness, compressive strength and the wear resistance
of the material do not change.
Vacuum
When used in a vacuum environment, the iglide® K plain bearings release moisture as vapor. Therefore, only dehumidified bearings
are suitable in a vacuum environment.
247
iglide®
GLW iglide® GLW - Low cost material for high quantities
For high quantities and medium loads
Cost-effective
Resistant to vibrations
Contact igus®
$ Order dependent
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 1,116,500 DIN 53457
Tensile strength at 68°F psi 34,075 DIN 53452
Compressive strength psi 10,730
Permissible static surface pressure (68°F) psi 11,600
Shore D-hardness 78 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1011 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 10
The graph shows the elastic deformation of iglide® GLW for radial loads. 8
At the maximum permissible load of 10,150 psi at room temperature,
the deformation is less than 3%. At this load, a plastic deformation is 6
D eformation in %
0
0 1450 2900 4350 5800 7250 8700 10150
Load (psi)
73 °F 140 °F
14,500
Permissible Surface Speeds
iglide ® GLW was developed for low to average surface speeds. In
constant operation, a maximum 157 fpm (rotating) or 492 fpm (lin-
ear) is permitted. Please note that the maximum values shown in the
1,450
table are only possible at the lowest pressure loads. In practice, these
values are rarely reached, due to the temperature increasing over the
maximum permitted value.
145
Pressure (psi)
14.5
1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures 11,600
10,150
Pressure (psi)
increasing temperatures, the compressive strength of iglide® GLW plain
2,900
bearings decreases. The graph shows this relationship.
1,450
With increasing temperatures in the bearing system, the wear also
0
increases.
0 68 104 140 176 212 248 284 320
Temperature in °F
➤ Application temperatures, Page 67
Recommended maximum permissible static surface
pressure of iglide® GLW as a result of the temperature
iglide® GLW Application Temperature
Minimum - 40°F
Max. long-term +212°F
Max. short-term +320°F
Additional axial securing +176°F
0.30
0.35
0.25
0.30
C oef ficient of friction μ
0.20
C oef ficient of friction μ
0.15
0.25
0.10
0.20
0.05
0.00
0.15
0 1450 2900 4350 5800 7250 8700 10150
9.84 19.69 29.53 39.37 49.22 59.05 68.90
Load (psi)
Surface Speed (fpm )
Coefficient of friction of iglide ® GLW as a result of
Coefficient of friction of iglide® GLW as a result of
the shaft surface v = 1.97 fpm (1050 hard chromed)
the surface speed p = 108 psi (1050 hard chromed)
30
To a large extent, friction and wear depend on the shaft material.
HR Carbon Steel
an extract of the results of tests with different shaft materials using 15
304 Stainless
Wear (µm/km)
iglide® GLW plain bearings. 10
If the shaft material you plan on using is not shown in these test results,
440B
1050
please contact us. 5
0
➤ Shaft Materials, Page 71
Wear with different shaft materials (p = 108 psi; v = 98 fpm)
most organic and inorganic acids. The moisture absorption of iglide® 0.6
GLW plain bearings is approximately 1% in standard atmosphere. The 0.5
saturation limit in water is 5%. This must be taken into account along 0.4
with other applicable conditions.
0.3
0.2
➤ Chemical table, Page 1364
0.1
0.0
0 1 2 3 4 5 6
M oistur e absorption (weight% )
Medium Resistance
Alcohol + to 0 Effect of moisture absorption on iglide® GLW plain
Hydrocarbon + bearings
Radiation Resistance
Plain bearings made from iglide® GLW are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® GLW plain bearings are permanently resistant to UV radiation.
Vacuum
In a vacuum environment, iglide® GLW plain bearings release gases. Use in a vacuum should be tested beforehand.
Ø 2 to 40 mm
mm
more dimensions on request
Under a vehicle body, bearings come into contact with heavy diurt Self-lubricating iglide® bearings are resistant to aggressive cleaning
accumulation. products used in this blow film line.
Two linear and one rotary motion are combined with self-lubricating Dirt-resistant iglide® bearings are generally recommended for
iglide® bearings in the tightest installation spaces. extremely high loads at low to medium speeds.
On this packaging machinery, iglide® bearings stand up to To ensure the long-term durability of street sweepers, the
temperatures often reaching +320 °F or above in continuous manufacturer decided to utilize self-lubricating, maintenance-free
operation. iglide® bearings.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® J260 l l l l
iglide® J3 l l l l
iglide® J350 l l l l l l
iglide® W360 l l l
iglide® L250 l l l
iglide® D l
iglide® J200 l l l l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® J260 l l l
iglide® J3 l l l
iglide® J350 l l l l
iglide® W360 l l l l
iglide® L250 l l
iglide® D l l l l
iglide® J200 l l l
iglide® J3 267
iglide® D 307
iglide® J3 7 3 267
iglide® D 7 7 307
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
259
iglide®
J260 iglide® J260 - Ideal for plastic shafts
Good wear resistance at medium loads
Self-lubricating and iglide ® J260 is a perfect material for long service life
maintenance-free and best coefficient of friction with special operating
conditions such as contact with plastic shafts.
Mechanical Properties
Modulus of elasticity psi 319,100 DIN 53457
Tensile strength at 68°F psi 8,702 DIN 53452
Compressive strength psi 7,252
Permissible static surface pressure (68°F) psi 5,802
Shore D-hardness 77 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1010 DIN 53482
4
Compressive Strength
The graph shows the elastic deformation of iglide® J260 during radial 3
loading. At the recommended maximum surface pressure of 5,802 psi
the deformation is less than 2.5%. The plastic deformation is minimal
2
up to a pressure of approximately 14,500 psi. However, it is also
Deformation (%)
14,500
Permissible Surface Speeds
iglide® J260 has been developed for low to medium surface speeds.
The maximum values shown in the table can only be achieved at
1,450
low pressure. At the given speeds, friction can cause a temperature
increase to maximum permissible levels. In practice though, this
temperature level is rarely reached, due to varying application
conditions.
145
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures 8,702
iglide® J260 plain bearings can be used at temperatures from -148°F 7,252
Pressure (psi)
2,901
0
68 86 104 122 140 158 176 194 212 230 248
Temperature (°F)
0.25 0.25
0.20
0.20
Coefficient of friction (µ)
0.15
0.15
0.10
0.10
0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90 2,901
0 1,450 4,351 5,802
Coefficients of friction of iglide® J260 as a function Coefficients of friction of iglide® J260 as a function
of the running speed; p = 108 psi of the load, v = 1.96 fpm
Wear (µm/km)
3.0
steel and hard chromed shafts. In this connection it is important to 2.0
note that with increasing loads the recommended hardness of the 1.0
shaft increases. The soft shafts tend to wear more easily and therefore 0.0
increase the wear of the overall system, if the loads exceed 290 psi. 0 145 290 435 580 725
The graph top right shows that with increasing load the wear on hard- Pressure (psi)
chromed shafts and 304 stainless rises less strongly than on 1050 and 1050 Steel 304 SS
HR carbon steel shafts. The comparison of rotation and oscillating in HR carbon steel Hard chromed
the graph lower right makes it very clear where iglide® J260 bearings
Wear of iglide ® J260 with different shaft materials in
are best used, especially in rotary operations.
rotational applications
➤ Shaft Materials, Page 71
120
100
3.0
80
2.5
60
Hard anodized aluminum
2.0
Automatic screw steel
Wear (µm/km)
1050, hard chromed
40
HR Carbon Steel
1.5
High grade steel
20
304 Stainless
Wear (µm/km)
1.0
0
145 290 725 1,450 2,901 6,527
0.5
1050
Pressure (psi)
Wear of iglide® J260, rotating applications with different Wear with different shaft materials, oscillating and
shaft materials, p = 145 psi, v = 59 fpm rotating movement p = 290 psi
Chemical Resistance
0.20
iglide® J260 plain bearings are resistant to diluted alkalis, hydrocarbons
and alcohols. The very low moisture absorption also permits use in
0.15
wet or damp environments.
0.05
0.00
0.0 0.1 0.2 0.3 0.4
Radiation Resistance
Plain bearings made from iglide® J260 are radiation resistant up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® J260 plain bearings are partially resistant to UV radiation.
Vacuum
In a vacuum, any moisture absorbed in the material would be outgassed. For this reason only dehumidified iglide ® J260 are suitable
for vacuum use.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
J260SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
J260SM-0810-06 8.0 10.0 6.0 10.000 10.015 7.964 8.000
8.025 8.083
J260SM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
J260SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
J260SM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
12.032 12.102
J260SM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
J260SM-1618-15 16.0 18.0 15.0 18.000 18.018 15.957 16.000
16.032 16.102
J260SM-1618-135 16.0 18.0 13.5 18.000 18.018 15.957 16.000
J260SM-1820-12 18.0 20.0 12.0 20.000 20.021 17.957 18.000
18.032 18.102
J260SM-1820-20 18.0 20.0 20.0 20.000 20.021 17.957 18.000
J260SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
J260 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
J260FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
J260FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
J260FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
J260FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
J260FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
J260FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
267
iglide®
J3 iglide® J3 - Triple the service life compared to iglide® J
Low coefficients of friction
Mechanical Properties
Modulus of elasticity psi 391,600 DIN 53457
Tensile strength at 68°F psi 10,150 DIN 53452
Compressive strength psi 8,702
Permissible static surface pressure (68°F) psi 6,527
Shore D-hardness 73 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
10
Compressive Strength 9
The graph shows the elastic deformation of iglide® J3 with radial 8
loads. Under the maximum recommended surface pressure of 6527 7
6
psi, the deformation is less than 6%. The plastic deformation is
5
minimal up to a pressure of approximately 14,500 psi. The possible
Deformation (%)
4
plastic deformation depends on the applied pressure, as well as other 3
external factors. 2
1
0
➤ Compressive strength, Page 63 0 725 1450 2176 2901 3626 4351 5076 5802 6527
Pressure (psi)
140°F 73°F
14.5
➤ Surface speed, Page 64
➤ pv value, Page 65
Pressure (psi)
1.45
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures 13050
11600
Pressure (psi)
4351
significant when temperatures rise over 194°F.
2901
1450
➤ Application temperatures, Page 67
0
68 86 104 122 140 158 176 194
Temperature (°F)
0.25 0.25
0.20 0.20
Coefficient of friction (µ)
0.15
0.15
0.10
0.10
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 2176 3626 5076 6527
HR Carbon Steel
proved to be the best. But even in combination with other shaft
304 Stainless
0.6
Wear (µm/km)
materials, except for free cutting steel, iglide ® J3 bearings achieve
0.4
excellent wear values. The graph to the right shows that the difference
440B
1050
between shaft materials increase with increasing loads. Hard chromed 0.2
or 304 stainless shafts are best at pressures from 290 psi in rotation 0.0
movement. The graph below right shows rotating and oscillating tests
in comparison. With higher load, the wear increases more for rotating Wear of iglide® J3, rotating applications with different
than for oscillating movements. shaft materials, p = 108 psi, v = 98 fpm
4.5 45
4.0 40
3.5 35
3.0 30
2.5 25
2.0 20
Wear (µm/km)
Wear (µm/km)
1.5 15
1.0 10
0.5 5
0.0 0
0 145 290 435 580 725 0 725 1450 2176 2901 3626 4351 5076 5802 6527
Pressure (psi)
1050 Steel HR carbon steel 304 SS Hard chromed
Rotating Oscillating
Chemical Resistance
0.25
0.00
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4
Radiation Resistance
Plain bearings made from iglide® J3 are radiation resistant up to an intensity of 1 x 104 Gy.
UV-Resistance
iglide® J3 plain bearings become discolored under UV radiation. However, hardness, compressive strength and the wear resistance
of the material do not change.
Vacuum
In vacuum applications, any absorbed moisture content is outgassed. For this reason only dehumidified iglide ® J3 bearings are suitable
for use in a vacuum.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
J3SM-0304-05 3.0 4.5 5.0 3.014 3.054 4.500 4.512 2.975 3.000
J3SM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
4.020 4.068
J3SM-0405-06 4.0 5.5 6.0 5.500 5.512 3.970 4.000
J3SM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
5.020 5.068
J3SM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
J3SM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
J3SM-0608-08 6.0 8.0 8.0 6.020 6.068 8.000 8.015 5.970 6.000
J3SM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
J3SM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
J3SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
J3SM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
J3SM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
J3SM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
J3SM-1012-12 10.0 12.0 12.0 10.025 10.083 12.000 12.018 9.964 10.000
J3SM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
J3SM-1012-20 10.0 12.0 20.0 12.000 12.018 9.964 10.000
J3SM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
J3SM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
12.032 12.102
J3SM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
J3SM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
J3SM-1315-10 13.0 15.0 10.0 15.000 15.018 12.957 13.000
13.032 13.102
J3SM-1315-20 13.0 15.0 20.0 15.000 15.018 12.957 13.000
J3SM-1416-15 14.0 16.0 15.0 16.000 16.018 13.957 14.000
J3SM-1416-20 14.0 16.0 20.0 14.032 14.102 16.000 16.018 13.957 14.000
J3SM-1416-25 14.0 16.0 25.0 16.000 16.018 13.957 14.000
J3SM-1517-15 15.0 17.0 15.0 17.000 17.018 14.957 15.000
J3SM-1517-20 15.0 17.0 20.0 17.000 17.018 14.957 15.000
15.032 15.102
J3SM-1517-25 15.0 17.0 25.0 17.000 17.018 14.957 15.000
J3SM-1517-30 15.0 17.0 30.0 17.000 17.018 14.957 15.000
J3SM-1618-15 16.0 18.0 15.0 18.000 18.018 15.957 16.000
J3SM-1618-20 16.0 18.0 20.0 16.032 16.102 18.000 18.018 15.957 16.000
J3SM-1618-25 16.0 18.0 25.0 18.000 18.018 15.957 16.000
J3SM-1820-15 18.0 20.0 15.0 20.000 20.021 17.957 18.000
J3SM-1820-20 18.0 20.0 20.0 18.032 18.102 20.000 20.021 17.957 18.000
J3SM-1820-25 18.0 20.0 25.0 20.000 20.021 17.957 18.000
J3SM-1821-25 18.0 21.0 25.0 18.032 18.102 21.000 21.021 17.957 18.000
J3SM-2023-10 20.0 23.0 10.0 20.040 20.124 23.000 23.021 19.948 20.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
J3SM-4550-50 45.0 50.0 50.0 45.050 45.150 50.000 50.025 44.938 45.000
J3SM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
J3SM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
J3SM-5055-40 50.0 55.0 40.0 50.050 50.150 55.000 55.030 49.938 50.000
J3SM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
J3SM-5055-60 50.0 55.0 60.0 55.000 55.030 49.938 50.000
30°
J3 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
J3FM-0203505-05 2.0 3.5 5.0 5.0 0.75 2.014 2.054 3.500 3.512 1.975 2.000
J3FM-0304-05 3.0 4.5 7.5 5.0 0.75 3.014 3.054 4.000 4.012 2.970 3.000
J3FM-0507-05 5.0 7.0 11.0 5.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
J3FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
J3FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
J3FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
J3FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
J3FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
8.025 8.083
J3FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
J3FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
J3FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
J3FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
J3FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
J3FM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
J3FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
J3FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
J3FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
J3FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
J3FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
J3FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.032 14.102
J3FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
J3FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
J3FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
J3FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
J3FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.032 16.102
J3FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
J3FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
J3FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
J3FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
J3FM-1821-12 18..0 21.0 30.0 21.5 1.5 18.032 18.102 21.000 21.021 17.957 18.000
J3FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
J3FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
J3FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
J3FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
J3FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
J3FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
J3FM-3034-16 30.0 34.0 42.0 16.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 271
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
J3FM-3034-26 30.0 34.0 42.0 26.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
J3FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.050 35.150
J3FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
J3FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.050 40.150
J3FM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
J3FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.050 45.150 50.000 50.025 44.938 45.000
279
iglide®
J350 iglide® J350 - Triple the service life compared to iglide® J
Low coefficients of friction
Mechanical Properties
Modulus of elasticity psi 290,100 DIN 53457
Tensile strength at 68°F psi 7,977 DIN 53452
Compressive strength psi 8,702
Permissible static surface pressure (68°F) psi 8,702
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1010 DIN 53482
6
Compressive Strength
5
iglide® J350 bearings are adequate for medium and high loads. The
graph shows the elastic deformation under different temperatures. 4
At the recommended maximum surface pressure of 8702 psi the
3
deformation is less than 6%.
Deformation (%)
1
➤ Compressive strength, Page 63
0
0 1450 2901 4351 5802 7252 8702
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
iglide ® J350 has been developed for low and medium speeds in
rotating and oscillating use. The wear rate is much better with rotating
1,450
movement.
iglide® J350 plain bearings can also be used for linear movement.
Temperatures 11600
Pressure (psi)
the bearing to drift within the housing bore. 2901
The wear-rate of iglide ® J350 bearings changes very little at high
temperatures. In some cases, the wear even decreases at +212°F. 0
Generally, the wear figures between +68°F and +302°F are very 68 104 140 176 212 248 284 320 356
similar.
Temperature (°F)
The iglide® J350 is a highly wear-resistant bearing material, which can
also be used at higher temperatures. The combination of excellent Recommended maximum permissible static surface
tribological and thermal properties fills a gap in the group of long life pressure of iglide® J350 as a result of the temperature
materials.
0.30 0.20
0.25 0.10
Coefficient of friction (µ)
0.20 0.00
0 1450 2901 4351 5802 7252 8702
0.35
Coefficients of friction of iglide® J350 as a function
of the running speed; p = 108 psi 0.30
Coefficient of friction (µ)
0.25
iglide® J350 Coefficient of Friction
0.20
Dry 0.10 - 0.20
Grease 0.09 0.15
Coefficient of friction of iglide ® J350 against steel Coefficients of friction of iglide® J350 as a function of
(Shaft finish = 40 rms, 50 HRC) the shaft surface (1050 hard chromed)
The graphs show results of testing different shaft materials with plain 2.5
HR Carbon Steel
results of the test: iglide® J350 with 304 stainless steel. Not many
304 Stainless
Wear (µm/km)
1.0
1050 Steel
bearing materials are suitable for use with this rather difficult 304
stainless steel material and achieve good wear results. Also, iglide ® 0.5
440B
J350 shows good properties with hard-anodized aluminum shafts. If
the shaft material you plan on using is not shown in these test results, 0.0
please contact us.
Wear of iglide® J350, rotating applications with different
shaft materials, p = 145 psi, v = 59 fpm
➤ Shaft Materials, Page 71
20 16
14
15 12
10
10 8
6
Wear (µm/km)
Wear (µm/km)
5 4
2
0 0
145 290 725 1450 2901 145 290 725 1450
Pressure (psi) Pressure (psi)
1050 Steel 440B 304 Stainless Hard anodized aluminum 1050 Steel 440B 304 Stainless Hard anodized aluminum
Wear of iglide ® J350 with different shaft materials in Wear of iglide® J350, oscillating movement of different
rotational applications as a function of the pressure shaft materials according to applied load
30°
>18 to 30 -0 /-330
Length of chamfer Length >30 to 50 -0 /-390
>50 to 80 -0 /-460
Chemical Resistance
0.5
iglide® J350 plain bearings are resistant to diluted alkalis and acids,
alcohols, cleaning agents and lubricants. iglide® J350 will be attacked 0.4
by esters, ketones, chlorinated hydrocarbons, and other solvents.
0.1
0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
Radiation Resistance
Plain bearings made from iglide® J350 are radiation resistant up to an intensity of 2 x 102 Gy.
UV-Resistance
iglide® J350 plain bearings are conditionally resistant to UV radiation.
Vacuum
iglide J350 plain bearings outgas in a vacuum. Use in a vacuum environment is only possible with dehumidified bearings.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
J350 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
J350FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
J350FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
J350FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
J350FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.018 7.964 8.000
J350FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.018 7.964 8.000
8.013 8.071
J350FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.018 7.964 8.000
J350FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.018 7.964 8.000
J350FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
J350FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
J350FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
J350FM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
J350FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
J350FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
J350FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.016 12.086
J350FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
J350FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
J350FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.016 14.086
J350FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
J350FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
J350FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
J350FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
J350FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
J350FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
J350FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
J350FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
J350FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
J350FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
J350FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.020 20.104 23.000 23.021 19.948 20.000
J350FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
J350FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
J350FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.020 25.104 28.000 28.021 24.948 25.000
J350FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
J350FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
J350FM-3034-22 30.0 34.0 42.0 22.0 2.0 34.000 34.025 29.948 30.000
30.020 30.104
J350FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
J350FM-3034-37 30.0 34.0 42.0 37.0 2.0 34.000 34.025 29.948 30.000
J350FM-3539-16 35.0 39.0 47.0 16.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 283
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
J350FM-3539-26 35.0 39.0 47.0 26.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000
J350FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.025 40.125
J350FM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
J350FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.050 45.150 50.000 50.025 44.938 45.000
291
iglide®
W360 iglide® W360 - General purpose endurance runner
Highly wear-resistant
Mechanical Properties
Modulus of elasticity psi 555,350 DIN 53457
Tensile strength at 68°F psi 17,259 DIN 53452
Compressive strength psi ND
Permissible static surface pressure (68°F) psi 10,878
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
4.0
Compressive Strength 3.5
With increasing temperatures, the compressive strength of iglide® W360 3.0
plain bearings decreases. The graph clarifies this relationship. At 356 °F the 2.5
surface pressure is still 1,450 psi. The recommended maximum surface 2.0
Deformation in %
14,500
Permissible Surface Speeds
iglide® W360 bearings are suitable for low to medium speeds in both
1,450
rotating and oscillating applications. Even linear movements can often be
realized with iglide® W360.
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures 11,600
10,150
The temperature resistance makes iglide® W360 a very universal material
8,702
for plain bearings in different industries. Application temperatures up to
+392 °F are permitted on the short term. Please note that from +194 °F 7,252
4,351
➤ Application temperatures, Page 67
Pressure (psi)
2,901
1,450
0
68 86 104 122 140 158 176 194 212 230 248 266 284 302
Temperature in (°F)
0.25 0.25
0.20 0.20
Coefficient of friction (µ)
0.15
Coefficient of friction µ
0.15
0.10 0.10
0.05 0.05
0 0
0 59 118 177 236 295 0 1,450 2,901 4,351 5,801 7,252 8,702 10,150
Coefficients of friction of iglide ® W360 as a function Coefficients of friction of iglide® W360 as a function
of the running speed; p = 145 psi of the load, v = 1.96 fpm
Shaft Materials
5
In the case of iglide® W360, the shaft’s surface finish has practically no
effect on the coefficient of friction in the range of up to 232 psi. The graphs 4
HR carbon steel
steel shafts stand out. A similar picture also exists with other loads or 2
304 Stainless
Wear (µm/km)
1050 Steel
pivoting movements.
If the shaft material you plan on using is not shown in these test results, 1
440B
please contact us.
0
0.20
0.16
Coefficient of Friction µ
0.12
0.08
0.04
0
0.4 0.6 0.8 1.0 1.2 1.4 1.6
Chemical Resistance
➤ Chemical table, Page 1364
Medium Resistance
Alcohol 0 to –
Hydrocarbon +
Greases, oils without additives +
Fuels +
Weak acids 0 to –
Strong acids 0 to –
Weak alkaline +
Strong alkaline +
+ resistant, 0 conditionally resistant, – not resistant
Moisture absorption
The moisture absorption of iglide® W360 is low and can be used in a humid environment. With a maximum absorption rate of 1.6 %, underwater use is
only possible when reduction of the ID is taken into account.
Radiation Resistance
Plain bearings made from iglide® W360 are resistant to radiation up to an intensity of 2 · 102 Gy.
UV-Resistance
iglide® W360 plain bearings are partially resistant to UV radiation.
Vacuum
In a vacuum, iglide® W360 bearing outgases only to a very small extent. Use in vacuum is possible with dehumidified bearings.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
W360SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
W360SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
W360SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
W360SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
W360SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
W360SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
W360 F M -06 08-06
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
W360FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
W360FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
W360FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
W360FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
W360FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
W360FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
299
iglide®
L250 iglide® L250 - For high speeds
For fast rotating applications
Specially made for Plain bearings for high speed rotation applications,
fast rotating applications especially for fans and motors.
Mechanical Properties
Modulus of elasticity psi 282,800 DIN 53457
Tensile strength at 68°F psi 9,718 DIN 53452
Compressive strength psi 6,817
Permissible static surface pressure (68°F) psi 6,527
Shore D-hardness 68 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1010 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength
10
With increasing temperatures, the compressive strength of iglide®
L250 plain bearings decreases. The Graph shows this inverse
relationship. However, at the long term maximum temperature of
+194°F the permissible surface pressure is almost 2,901 psi.
Deformation (%)
0
0 2,176 4,351 6,527
Pressure (psi)
140°F 73°F
Temperatures 17400
iglide® L250 plain bearings can be used at temperatures from -40°F up 14500
Pressure (psi)
5802
0
68 86 104 122 140 158 176 194
Temperature (°F)
0.5 0.7
0.6
0.4
0.5
Coefficient of friction (µ)
0.4
0.3
0.3
0.2 0.2
0.1
0.1 0.0
9.84 19.69 29.53 39.37 49.21 59.06 0 1,450 2,901 4,351 5,802 7,252 8,702 10,150 11,600
Coefficients of friction of iglide® L250 as a function Coefficients of friction of iglide® L250 as a function
of the running speed; p = 108 psi of the load, v = 1.96 fpm
HR carbon steel
304 Stainless
Wear (µm/km)
0.2
1050 Steel
➤ Shaft Materials, Page 71
0.1
440B
0.0
200
180 2.4
160
2.0
140
120 1.6
100
1.2
80
Wear (µm/km)
Wear (µm/km)
60 0.8
40
0.4
20
0 0.0
0 725 1450 2176 2901 3626 4351 5076 0.0 72 145 217 290
Wear with different shaft materials, oscillating and Wear of iglide ® L250 with different shaft materials in
rotating movement p = 290 psi rotational applications
Chemical Resistance
0.16
iglide ® L250 bearings are resistant to diluted alkalis and very weak
0.14
acids as well as solvents and all types of lubricants.
0.12
0.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Radiation Resistance
Plain bearings made from iglide® L250 are radiation resistant up to an intensity of 3 x 104 Gy. Higher radiation affects the material and
may result in a significant decrease in mechanical properties.
UV-Resistance
When subjected to UV radiation, iglide® L250 plain bearings become discolored. However, hardness, compressive strength and the
wear resistance of the material are not effected.
Vacuum
In vacuum applications, any absorbed moisture content is outgassed. For this reason only dehumidified iglide ® L250 bearings are
suitable for use in a vacuum.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
L250SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
L250SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
L250SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
L250SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
L250SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
L250SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
L250 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
L250FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
L250FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
L250FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
L250FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
L250FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
L250FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
307
iglide®
D iglide® D - Low cost material with silicone
Economic
Vibration dampening
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 290,100 DIN 53457
Tensile strength at 68°F psi 10,440 DIN 53452
Compressive strength psi 10,150
Permissible static surface pressure (68°F) psi 3,336
Shore D-hardness 78 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1014 DIN IEC 93
Surface resistance Ω > 1014 DIN 53482
10
Compressive Strength
iglide ® D plain bearings were developed for low to average radial 8
loads. The graph shows the elastic deformation of iglide® D for radial
6
loads. At the recommended maximum surface pressure of 3,336
psi, the deformation is approximately 3%. Plastic deformation is not
Deformation (%)
4
detectable up to this value. However, it is also dependent on the
temperature. 2
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures 4,351
Pressure (psi)
1,450
0
68 86 104 122 140 158 176 194
Temperature (°F)
iglide® D Application Temperature Recommended maximum permissible static surface
Minimum - 58°F pressure of iglide® D as a result of the temperature
0.35
0.4 0.30
0.25
Coefficient of friction (µ)
0.3 0.20
Coefficient of friction (µ)
0.15
0.10
0.2
0.05
0.00
0 725 1,450 2,176 2,901
0.1
9.84 19.69 29.53 39.37 49.21 59.06 68.90 78.74 Pressure (psi)
Shaft Materials 9
8
The graphs show results of testing different shaft materials with plain 7
bearings made of iglide® D. 6
In the low load range, the hard chromed shaft is the most suitable 5
material for iglide® D plain bearings. At loads greater than 290 psi, 4
Wear (µm/km)
shafts made of 1050 hardened and ground steel as well as 304 3
8
10
7 9
8
6
Hard anodized aluminum
7
Automatic screw steel
5 6
1050, hard chromed
5
HR Carbon Steel
4
4
304 Stainless
3
Wear (µm/km)
Wear (µm/km)
3
2 2
440B
1050
1 1
0
0 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
Wear of iglide ® D, rotating applications with different Oscillating Rotating
shaft materials, p = 108 psi, v = 98 fpm
Wear with different shaft materials, oscillating and
rotating movement p = 290 psi
Chemical Resistance
0.10
iglide ® D plain bearings are resistant to very weak acids, diluted 0.09
alkalis, fuel and all types of lubricants. 0.08
The moisture absorption of iglide® D plain bearings is approximately 0.07
Radiation Resistance
Plain bearings made from iglide® D are radiation resistant up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® D plain bearings are resistant to UV radiation, but the tribological properties are reduced by permanent exposure.
Vacuum
In vacuum environment, iglide® D plain bearings release gases. It is only possible to use iglide® D in a vacuum to a limited extent.
313
iglide®
J200 iglide® J200 - Specially for aluminum shafts
Low coefficients of friction
Very long service life with hard iglide ® J200 is a specialist for low friction values and
anodized aluminum shaft minimal wear with hard anodized aluminum shaft.
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 406,100 DIN 53457
Tensile strength at 68°F psi 8,412 DIN 53452
Compressive strength psi 6,237
Permissible static surface pressure (68°F) psi 3,336
Shore D-hardness 70 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 108 DIN IEC 93
Surface resistance Ω > 108 DIN 53482
10.0
Compressive Strength
The comparison to the other iglide® materials reveals that iglide® J200
plain bearings are more suitable for lower loads. The graph shows the 6.5
deformation of the material at room temperature to the recommended
maximum limit. As with all thermoplastics, the compressive strength
Deformation (%)
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures 3,626
Plain bearings made of iglide ® J200 were not developed for high 2,901
temperatures. The maximum permissible temperature of 248°F may
not be exceeded. Also, the heat produced by friction has to be added 2,176
to the ambient temperature. Even from 140°F, the bearings should be
1,450
secured mechanically, preventing the bearing from moving out of the
Pressure (psi)
housing. Also, the wear resistance decreases significantly from 158°F.
725
Temperature (°F)
iglide J200
® Application Temperature Recommended maximum permissible static surface
Minimum - 58°F pressure of iglide® J200 as a result of the temperature
0.70
0.5 0.60
0.50
Coefficient of friction (µ)
0.4
0.40
Coefficient of friction (µ)
0.30
0.3
0.20
0.2 0.10
0.00
0 1,450 2,901
0.1
9.84 19.69 29.53 39.37 Pressure (psi)
Shaft Materials
The shaft material used has a great impact on the wear resistance. 5.0
In fact, all shaft materials (smooth or hardened) are suitable for use 4.5
with iglide ® J200. However, the best results are achieved with hard 4.0
304 Stainless
➤ Shaft Materials, Page 71 2.0
Wear (µm/km)
1.5
1.0
1050
0.5
0.0
12
80
10 70
60
8
50
6 40
30
Wear (µm/km)
Wear (µm/km)
4
20
2
10
0 0
0.0 72 145 217 290 0 725 1,450 2,176 2,901 3,626
Pressure (psi) Pressure (psi)
rotating oscillating
1050 Steel HR carbon steel 304 SS Hard chromed
Wear of iglide ® J200 with different shaft materials in Wear with different shaft materials, oscillating and
rotational applications rotating movement p = 290 psi
Chemical Resistance
0.24
iglide® J200 plain bearings are resistant to diluted alkaline, as well as
0.21
to solvents and all types of lubricants.
0.18
The moisture absorption of iglide ® J200 plain bearings in standard
0.00
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
Radiation Resistance
Plain bearings made from iglide® J200 are radiation resistant up to an intensity of 2 x 102 Gy.
UV-Resistance
iglide® J200 plain bearings are conditionally resistant to UV radiation.
Vacuum
iglide J200 plain bearings outgas in a vacuum. Use in a vacuum environment is only possible with dehumidified bearings.
max. +482 °F
min. –148 °F
4 materials
Ø 3 to 120 mm
mm
more dimensions on request
iglide® bearings are used in the straightening machine for their iglide® thrust washers are in use in these high-speed thermal
ability to run for long operating times under high loads. shakers in the laboratory.
iglide® Z bearings eliminated maintenance by 95%, and reduced The hinge elements and ramp rollers are each fitted with two iglide®
costs by 54% in this thrill ride. Z plain bearings. The stainless steel axles that connect the fixed
part of the hinge run through the bearing.
Efficient hardening with UV radiation – iglide® bearings are able to Self-lubricating iglide® bearings in a milk bottle filling system are
withstand chemicals and the application temperature of +248 °F. resistant to disinfectants and high temperatures.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® X6 l l l l l
iglide® V400 l l l l
iglide® Z l l l l l
iglide® UW500 l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® X6 l l l
iglide® V400 l l l l
iglide® Z l l l l
iglide® UW500 l l l l
iglide® X6 325
iglide® Z 343
iglide® X6 6 5 325
iglide® Z 1 3 343
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
iglide® X6
• Long term service temperature up to +482°F
• Up to 50% more pressfit than iglide T500
®
325
iglide®
X6 iglide® X6 - Runs up to 6 times longer than iglide® T500
Long term service temperature up to 482°F
Mechanical Properties
Modulus of elasticity psi 2,320,600 DIN 53457
Tensile strength at 68°F psi 42,060 DIN 53452
Compressive strength psi 27,557
Permissible static surface pressure (68°F) psi 21,755
Shore D-hardness 89 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 105 DIN IEC 93
Surface resistance Ω < 105 DIN 53482
3.0
Compressive Strength
2.5
The recommended maximum surface pressure is a mechanical material
parameter. No conclusions regarding the tribological properties can be 2.0
drawn from this. With increasing temperatures, the compressive strength
1.5
Deformation (%)
145,000
Permissible Surface Speeds
Due to the high temperature resistance and good thermal conductivity,
iglide® X6 is also suitable for high speed applications. At the given speeds,
14,500
friction can cause a temperature increase to maximum permissible levels.
In practice, this temperature is rarely reached due to varying application
1450 conditions.
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures 21,760
19,580
The surrounding temperatures noticeably influence the wear 17,400
performance of plastic bearings. The temperature resistance of iglide ® 15,230
13,050
X6 is among the highest in the iglide® range.
10,880
In many tests it has shown a six times higher wear performance
8,702
Pressure (psi)
compared to the established high-temperature bearing iglide® T500. 6,527
Another advantage to iglide ® X6 is that axial securing is only necessary 4,351
at temperatures above 320°F. 2,176
0
68 122 176 248 302 392 482
➤ Application temperatures, Page 67
Temperature °F
0.40 0.35
Coefficient of friction (µ)
0.30
Coefficient of friction (µ)
0.35
0.25
0.30
0.20
0.25 0.15
0.10
0.20
0.05
0.15
0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90
1450 4350 7252 10150 13050
0 2900 5800 8702 11600
Coefficient of friction for iglide® X6 as a result of the Coefficient of friction as a function of the pressure,
running speed; p = 109 psi v = 1.96 fpm
Shaft Materials 50
45
40
The friction and wear are also dependent, to a large degree, on the
35
shaft material. Shafts that are too smooth, increase both the coefficient
30
of friction and the wear of the bearing. The best case for iglide® X6 is
25
a ground surface with an average roughness rms 16-32. The graphs
20
Wear (µm/km)
show the results of testing different shaft materials with plain bearings 15
made of iglide® X6. In the graph below it shows that iglide® X6 can be 10
combined with various shaft materials 5
0
➤ Shaft Materials, Page 71 0 145 290 435 580 725 870 1015 1160 1305 1450
Pressure (psi)
rotating oscillating
Wear for oscillating and rotating applications with shaft
materials 1050 hard chromed and ground steel, as a
function of the pressure
35
7 30
6 25
Hard anodized aluminum
5 20
Automatic screw steel
Wear (µm/km)
15
1050, hard chromed
4
HR carbon steel
10
Wear (µm/km)
3
304 Stainless
5
1050 steel
2
0
440B
Pressure (psi)
0
1050 steel 304 Stainless
Wear rotating with different shaft materials, p = 145 HR carbon steel Hard chromed
psi, v = 59 fpm
Wear with different shaft materials in rotational operation,
as a function of the pressure
Chemical Resistance
0.10
0.00
0.0 0.2 0.4 0.6
Radiation Resistance
Plain bearings made from iglide® X6 are resistant to radiation up to an intensity of 2 x 105 Gy.
UV-Resistance
Partially resistant against UV rays
Vacuum
In a vacuum environment, iglide® X6 plain bearings can be used virtually without restrictions. Outgassing takes place to a very limited
extent.
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
30°
d1
For tolerance values
Inch
please refer to page 329
*Based on steel housing bore
X6SI-0203-03 1/8 3/16 3/16 .1251 .1269 .1873 .1878 .1236 .1243
X6SI-0304-04 3/16 1/4 1/4 .1873 .1892 .2497 .2503 .1858 .1865
X6SI-0405-04 1/4 5/16 1/4 .3122 .3128 .2481 .2490
.2498 .2521
X6SI-0405-08 1/4 5/16 1/2 .3122 .3128 .2481 .2490
X6SI-0506-06 5/16 3/8 3/8 .3125 .3148 .3747 .3753 .3106 .3115
X6SI-0607-06 3/8 15/32 3/8 .3750 .3773 .4684 .4691 .3731 .3740
X6SI-0708-08 7/16 17/32 1/2 .4379 .4406 .5309 .5316 .4355 .4365
X6SI-0809-08 1/2 19/32 1/2 .5934 .5941 .4980 .4990
X6SI-0809-10 1/2 19/32 5/8 .5003 .5030 .5934 .5941 .4980 .4990
X6SI-0809-12 1/2 19/32 3/4 .5934 .5941 .4980 .4990
X6SI-1011-10 5/8 23/32 5/8 .6253 .6280 .7184 .7192 .6230 .6240
X6SI-1214-08 3/4 7/8 1/2 .8747 .8755 .7479 .7491
X6SI-1214-12 3/4 7/8 3/4 .7507 .7541 .8747 .8755 .7479 .7491
X6SI-1214-16 3/4 7/8 1 .8747 .8755 .7479 .7491
X6SI-1416-16 7/8 1 1 .8757 .8791 .9997 1.0005 .8729 .8741
X6SI-1618-08 1 1 1/8 1/2 1.1247 1.1255 .9979 .9991
X6SI-1618-12 1 1 1/8 3/4 1.0007 1.0041 1.1247 1.1255 .9979 .9991
X6SI-1618-16 1 1 1/8 1 1.1247 1.1255 .9979 .9991
X6SI-2426-12 1 1/2 1 21/32 3/4 1.6558 1.6568 1.4972 1.4988
X6SI-2426-16 1 1/2 1 21/32 1 1.5008 1.5048 1.6558 1.6568 1.4972 1.4988
X6SI-2426-24 1 1/2 1 21/32 1 1/2 1.6558 1.6568 1.4972 1.4988
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
please refer to page 329
Inch
*Based on steel housing bore
X6FI-0203-03 1/8 3/16 .312 3/16 .032 .1873 .1878 .1236 .1243
.1251 .1269
X6FI-0203-06 1/8 3/16 .312 3/8 .032 .1873 .1878 .1236 .1243
X6FI-0304-04 3/16 1/4 .375 1/4 .032 .1873 .1892 .2497 .2503 .1858 .1865
X6FI-0405-04 1/4 5/16 .500 1/4 .032 .2498 .2521 .3122 .3128 .2481 .2490
X6FI-0506-06 5/16 3/8 .562 3/8 .032 .3125 .3148 .3747 .3753 .3106 .3115
X6FI-0607-06 3/8 15/32 .687 3/8 .046 .3750 .3773 .4684 .4691 .3731 .3740
X6FI-0708-08 7/16 17/32 .750 1/2 .046 .4379 .4406 .5309 .5316 .4355 .4365
X6FI-0809-08 1/2 19/32 .875 1/2 .046 .5934 .5941 .4980 .4990
X6FI-0809-10 1/2 19/32 .875 5/8 .046 .5003 .5030 .5934 .5941 .4980 .4990
X6FI-0809-12 1/2 19/32 .875 3/4 .046 .5934 .5941 .4980 .4990
X6FI-1011-10 5/8 23/32 .937 5/8 .046 .7184 .7192 .6230 .6240
.6253 .6280
X6FI-1011-12 5/8 23/32 .937 1/2 .046 .7184 .7192 .6230 .6240
X6FI-1214-08 3/4 7/8 1.125 1/2 .062 .8747 .8755 .7479 .7491
X6FI-1214-12 3/4 7/8 1.125 3/4 .062 .7507 .7541 .8747 .8755 .7479 .7491
X6FI-1214-16 3/4 7/8 1.125 1 .062 .8747 .8755 .7479 .7491
X6FI-1416-12 7/8 1 1.250 3/4 .062 .9997 1.0005 .8729 .8741
.8757 .8791
X6FI-1416-16 7/8 1 1.250 1 .062 .9997 1.0005 .8729 .8741
X6FI-1618-08 1 1 1/8 1.375 1/2 .062 1.1247 1.1255 .9979 .9991
X6FI-1618-12 1 1 1/8 1.375 3/4 .062 1.0007 1.0041 1.1247 1.1255 .9979 .9991
X6FI-1618-16 1 1 1/8 1.375 1 .062 1.1247 1.1255 .9979 .9991
X6FI-2426-16 1 1/2 1 21/32 2.000 1 .078 1.6558 1.6568 1.4972 1.4988
1.5008 1.5048
X6FI-2426-24 1 1/2 1 21/32 2.000 1 1/2 .078 1.6558 1.6568 1.4972 1.4988
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
X6SM-0304-03 3.0 4.5 3.0 3.006 3.046 4.500 4.512 2.975 3.000
X6SM-0507-05 5.0 7.0 5.0 5.010 5.058 7.000 7.015 4.970 5.000
X6SM-0608-06 6.0 8.0 6.0 6.010 6.058 8.000 8.015 5.970 6.000
X6SM-0810-10 8.0 10.0 10.0 8.013 8.071 10.000 10.015 7.964 8.000
X6SM-1012-10 10.0 12.0 10.0 10.013 10.071 12.000 12.018 9.964 10.000
X6SM-1214-12 12.0 14.0 12.0 12.016 12.086 14.000 14.018 11.957 12.000
X6SM-1618-15 16.0 18.0 15.0 16.016 16.086 18.000 18.018 15.957 16.000
X6SM-2023-20 20.0 23.0 20.0 20.020 20.104 23.000 23.021 19.948 20.000
X6SM-2528-30 25.0 28.0 30.0 25.020 25.104 28.000 28.021 24.948 25.000
X6SM-3034-30 30.0 34.0 30.0 30.020 30.104 34.000 34.025 29.948 30.000
X6SM-3539-40 35.0 39.0 40.0 35.025 35.125 39.000 39.025 34.938 35.000
X6SM-4044-40 40.0 44.0 40.0 40.025 40.125 44.000 44.025 39.938 40.000
X6SM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000
30°
X6 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
X6FM-0304-05 3.0 4.5 7.5 5.0 0.75 3.006 3.046 4.500 4.512 2.975 3.000
X6FM-0507-05 5.0 7.0 11.0 5.0 1.0 5.010 5.058 7.000 7.015 4.970 5.000
X6FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
X6FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.013 8.071 10.000 10.015 7.964 8.000
X6FM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
10.013 10.071
X6FM-1012-25 10.0 12.0 18.0 25.0 1.0 12.000 12.018 9.964 10.000
X6FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
X6FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
X6FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
X6FM-2023-21 20.0 23.0 30.0 21.0 1.5 20.020 20.104 23.000 23.021 19.948 20.000
X6FM-2528-21 25.0 28.0 35.0 21.0 1.5 25.020 25.104 28.000 28.021 24.948 25.000
X6FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
30.020 30.104
X6FM-3034-40 30.0 34.0 42.0 40.0 2.0 34.000 34.025 29.948 30.000
X6FM-3539-26 35.0 39.0 47.0 26.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000
X6FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
psi
iglide® V400
• Excellent wear resistance with soft shaft materials
• For temperatures up to 392°F
• Good chemical resistance
• High elasticity
335
iglide®
V400 iglide® V400 - For soft shafts, up to 392°F
High wear resistance
Excellent wear resistance Highly wear-resistant bearing for soft shafts and for tem-
with soft shafts peratures up to 392°F. Low moisture absorption and good
resistance to chemicals.
For temperatures
up to 392°F
High elasticity
Mechanical Properties
Modulus of elasticity psi 652,670 DIN 53457
Tensile strength at 68°F psi 13,779 DIN 53452
Compressive strength psi 6,819
Permissible static surface pressure (68°F) psi 6,527
Shore D-hardness 74 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Pressure (psi)
140°F 73°F
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures
The long-term maximum permissible application temperature is +392 °F, 11,600
for temperatures over +212 °F an additional securing is required. Then, 10,150
however, the wear resistance of the bearings is very good and adopts a 8,702
leading position among all iglide® materials. The compressive strength of 7,252
iglide® V400 plain bearings decreases with increasing temperatures. The
5,802
graph shows this relationship.
4,351
Pressure (psi)
2,901
➤ Application temperatures, Page 67
1,450
0
68 122 176 248 302 392
Temperature (°F)
0.5 0.7
0.6
0.4 0.5
Coefficient of friction (µ)
Coefficient of friction (µ)
0.4
0.3
0.3
0.2
0.2
0.1
0.0
0.1 0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
9.84 19.69 29.53 39.37 49.21 59.06
Pressure (psi)
Surface speed (fpm)
Coefficients of friction of iglide® V400 as a function Coefficients of friction of iglide® V400 as a function
of the running speed; p = 109 psi of the load, v = 1.96 fpm
Wear (µm/km)
60
40
➤ Shaft Materials, Page 71
20
0
0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
Pressure (psi)
Rotating Oscillating
12 12
11
10 10
9
Hard anodized aluminum
8
8
7
1050, hard chromed
6
6
HR Carbon Steel
Automatic steel
5
Wear (µm/km)
4
304 Stainless
Wear (µm/km)
4
3 2
2
440B
1050
1 0
0 0.0 72.52 145.0 217.6 290.1
Chemical Resistance
0.16
iglide ® V400 plain bearings are feature good chemical resistance. 0.14
They are resistant to detergents, greases, oils, alcohol, solvents,
Radiation Resistance
iglide® V400 bearings are resistant to a radiation intensity of 2 · 104 Gy. Higher radiation affects their mechanical characteristics.
UV-Resistance
iglide® V400 plain bearings are resistant to UV radiation to a large extent.
Vacuum
In a vacuum, iglide® V400 plain bearings can only be used to a limited degree. Outgassing takes place.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
V400SM-0608-06 6.0 8.0 6.0 6.010 6.058 8.000 8.015 5.970 6.000
V400SM-0810-10 8.0 10.0 10.0 8.013 8.071 10.000 10.015 7.964 8.000
V400SM-1012-10 10.0 12.0 10.0 10.013 10.071 12.000 12.018 9.964 10.000
V400SM-1214-12 12.0 14.0 12.0 12.016 12.086 14.000 14.018 11.957 12.000
V400SM-1618-15 16.0 18.0 15.0 16.016 16.086 18.000 18.018 15.957 16.000
V400SM-2023-20 20.0 23.0 20.0 20.020 20.104 23.000 23.021 19.948 20.000
30°
V400 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
V400FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
V400FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.013 8.071 10.000 10.015 9.964 10.000
V400FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
V400FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
V400FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.016 16.086 18.000 18.018 15.957 16.000
V400FM-1820-20 18.0 20.0 26.0 20.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
V400FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.020 20.104 23.000 23.021 20.948 21.000
psi
iglide® Z
• Excellent wear resistance especially with high loads
• High thermal resistance
• For extreme loads
• For high surface speeds
• Resistant to edge loads
343
iglide®
Z iglide® Z - For high dynamic loads, wear resistant
For extreme loads
Excellent wear resistance Extremely high compressive strength coupled with high
especially with high loads elasticity enables iglide® Z bearings to attain their prominent
features in association with soft shafts, edge loads and
impacts. At the same time, the bearings are suitable for
temperatures up to 482°F.
Mechanical Properties
Modulus of elasticity psi 348,100 DIN 53457
Tensile strength at 68°F psi 13,775 DIN 53452
Compressive strength psi 9,425
Permissible static surface pressure (68°F) psi 21,750
Shore D-hardness 81 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1011 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 8
7
Iglide® Z is a high-temperature bearing material, which is suited for 6
applications with very high loads. For radial pressures between 7,250 and
5
14,500 psi, there is no better dry running wear-resistant iglide® material.
4
The graph shows the elastic deformation of iglide® Z for radial loads. At
Deformation (%)
3
the maximum permissible load of 14,500, the deformation is approximately
2
5.5% at room temperature.
1
0
➤ Compressive strength, Page 63
0 4,351 8,702 13,050 17,400 21,760
Pressure (psi)
140°F 73°F
145,000
Permissible Surface Speeds
iglide ® Z is suited for both average and high speeds due to its high
14,500 thermal resistance. The maximum values given in the table can only
be achieved at the lowest pressure loads. At the given speeds, friction
can cause temperature to increase to maximum permissible levels.
1,450
14.5
.197 1.97 19.7 197 1,969
Temperatures 160
The maximum permissible short-term temperature is 590°F. This 140
represents the highest thermal resistance of any iglide® material. 120
With increasing temperatures, the compressive strength of iglide® Z plain 100
bearings decreases. The graph shows this relationship.
80
The ambient temperatures prevalent in the bearing system also have
60
an effect on the bearing wear. With increasing temperatures, the wear
Pressure (psi)
40
increases.
20
The graph shows that when the temperature increases from room
0
temperature to 302°F , the wear of iglide® Z only doubles. At high
68 122 176 248 302 392 482
temperatures, iglide® Z is also the most wear-resistant material while
running dry. Temperature (°F)
0.4 0.25
0.20
0.3
Coefficient of friction (µ)
0.15
0.10
0.2
0.05
0.1 0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 1450 2901 4351 5802 7252 8702 10150 11600
Coefficients of friction of iglide ® Z as a result of the Coefficients of friction of iglide ® Z as a result of the
running speed; p = 108 psi load, v = 1.97 fpm
Wear (µm/km)
40
less than in rotation. 303 Stainless Steel and hard-chromed shaft are
20
of interest here. The value 0.5 µm/km shows 303 Stainless provides
the lowest wear in oscillating movements at 280 psi. For higher loads, 0
0 2901 5802 8702 11600 14500
hard-chromed shafts outperform 303 Stainless. However even at 1450 4351 7252 10150 13050
14,500 psi, iglide® Z obtains excellent wear values. If the shaft material Pressure (psi)
you plan to use is not contained in this list, please contact us. Rotating Oscillating
12.0
10.0
Hard anodized aluminum
8.0
Automatic screw steel
HR Carbon Steel
6.0
304 Stainless
Wear (µm/km)
4.0
2.0
440B
1050
0.0
0.00
0.0 0.2 0.4 0.6 0.8 1.0 1.2
Medium Resistance
Alcohol 0 Moisture absorption (weight %)
Fuels +
Weak acids +
Strong acids –
Weak alkaline +
Strong alkaline –
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Plain bearings made from iglide® Z are resistant to radiation up to an intensity of 1 x 105 Gy.
UV Resistance
UV radiation causes approximately 50% decline of the tribological properties (wear) of plain bearings made from iglide® Z.
Vacuum
For use in a vacuum environment, moisture content is released as vapor. Therefore, only dehumidified bearings made of iglide® Z are
suitable for a vacuum environment.
Outer-Ø d2 (inch)
b1
Inner-Ø d1 (inch)
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
Inch
*Based on steel housing bore
ZSI-0203-03 1/8 3/16 3/16 .1247 .1266 .1873 .1878 .1236 .1243
ZSI-0304-06 3/16 1/4 3/16 .1873 .1892 .2497 .2503 .1858 .1865
ZSI-0405-08 1/4 5/16 1/2 .2498 .2521 .3122 .3128 .2481 .2490
ZSI-0506-06 5/16 3/8 3/8 .3120 .3143 .3747 .3753 .3106 .3115
ZSI-0607-04 3/8 15/32 1/4 .4685 .4691 .3731 .3740
ZSI-0607-06 3/8 15/32 3/8 .3745 .3768 .4685 .4691 .3731 .3740
ZSI-0607-08 3/8 15/32 1/2 .4685 .4691 .3731 .3740
ZSI-0708-08 7/16 17/32 1/2 .5307 .5316 .4355 .4365
.4371 .4399
ZSI-0708-12 7/16 17/32 3/4 .5307 .5316 .4355 .4365
ZSI-0809-12 1/2 19/32 3/4 .4996 .5024 .5933 .5941 .4980 .4990
ZSI-0810-12 1/2 5/8 3/4 .5006 .5034 .6248 .6260 .4990 .5000
ZSI-1011-12 5/8 23/32 3/4 .6246 .6274 .7185 .7192 .6230 .6240
ZSI-1214-12 3/4 7/8 3/4 .8748 .8755 .7479 .7491
.7499 .7532
ZSI-1214-16 3/4 7/8 1 .8748 .8755 .7479 .7491
ZSI-1416-16 7/8 1 1 .8749 .8782 .9997 1.0005 .8729 .8741
ZSI-1618-16 1 1 1/8 1 1.1247 1.1255 .9979 .9991
.9999 1.0032
ZSI-1618-24 1 1 1/8 1 1/2 1.1247 1.1255 .9979 .9991
ZSI-1820-24 1 1/8 1 9/32 1 1/2 1.1246 1.1279 1.2807 1.2818 1.1226 1.1238
ZSI-2022-20 1 1/4 1 13/32 1 1/4 1.2498 1.2537 1.4059 1.4068 1.2472 1.2488
ZSI-2426-24 1 1/2 1 21/32 1 1/2 1.4998 1.5037 1.6559 1.6568 1.4972 1.4988
ZSI-2831-32 1 3/4 1 15/16 2 1.7497 1.7536 1.9370 1.9381 1.7471 1.7487
ZSI-3235-16 2 2 3/16 1 2.1870 2.1883 1.9969 1.9981
1.9993 2.0040
ZSI-3235-32 2 2 3/16 2 2.1870 2.1883 1.9969 1.9981
ZSI-3639-32 2 1/4 2 7/16 2 2.2519 2.2566 2.4366 2.4377 2.2489 2.2507
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2 For tolerance values
r = max. .0197 d3 please refer to page 347
Inch
*Based on steel housing bore
ZFI-0304-06 3/16 1/4 3/8 .375 .032 .1873 .1892 .2497 .2503 .1858 .1865
ZFI-0405-08 1/4 5/16 1/2 .500 .032 .2495 .2518 .3122 .3128 .2476 .2490
ZFI-0506-06 5/16 3/8 3/8 .562 .032 .3120 .3143 .3747 .3753 .3101 .3115
ZFI-0607-08 3/8 15/32 1/2 .687 .046 .3745 .3768 .4684 .4691 .3731 .3740
ZFI-0708-08 7/16 17/32 1/2 .750 .046 .4371 .4399 .5307 .5314 .4348 .4365
ZFI-0809-08 1/2 19/32 1/2 .875 .046 .5934 .5941 .4980 .4990
.5003 .5030
ZFI-0809-12 1/2 19/32 3/4 .875 .046 .5934 .5941 .4980 .4990
ZFI-1012-08 5/8 3/4 1/2 1.000 .062 .7500 .7508 .6240 .6250
.6256 .6284
ZFI-1012-16 5/8 3/4 1 1.000 .062 .7500 .7508 .6240 .6250
ZFI-1214-12 3/4 7/8 3/4 1.125 .062 .8748 .8755 .7479 .7491
.7499 .7532
ZFI-1214-16 3/4 7/8 1 1.125 .062 .8748 .8755 .7479 .7491
ZFI-1416-12 7/8 1 3/4 1.250 .062 .9997 1.0005 .8729 .8741
.8749 .8782
ZFI-1416-16 7/8 1 1 1.250 .062 .9997 1.0005 .8729 .8741
ZFI-1618-08 1 1 1/8 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
ZFI-1618-16 1 1 1/8 1 1.375 .062 .9999 1.0032 1.1247 1.1255 .9979 .9991
ZFI-1618-24 1 1 1/8 1 1/2 1.375 .062 1.1247 1.1255 .9979 .9991
ZFI-1820-12 1 1/8 1 9/32 3/4 1.562 .078 1.2807 1.2818 1.1226 1.1238
1.1246 1.1279
ZFI-1820-24 1 1/8 1 9/32 1 1/2 1.562 .078 1.2807 1.2818 1.1226 1.1238
ZFI-2022-20 1 1/4 1 13/32 1 1/4 1.687 .078 1.4059 1.4068 1.2472 1.2488
1.2498 1.2537
ZFI-2022-24 1 1/4 1 13/32 1 1/2 1.687 .078 1.4059 1.4068 1.2472 1.2488
ZFI-2426-24 1 1/2 1 21/32 1 1/2 2.000 .078 1.4998 1.5037 1.6559 1.6568 1.4972 1.4988
ZFI-2831-32 1 3/4 1 15/16 2 2.375 .093 1.7497 1.7536 1.9370 1.9381 1.7471 1.7487
ZFI-3235-32 2 2 3/16 2 2.625 .093 1.9993 2.0040 2.1870 2.1883 1.9969 1.9981
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
ZSM-3236-40 32.0 36.0 40.0 32.025 32.125 36.000 36.025 31.938 32.000
ZSM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
ZSM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
ZSM-3539-35 35.0 39.0 35.0 35.025 35.125 39.000 39.025 34.938 35.000
ZSM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
ZSM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
ZSM-4044-15 40.0 44.0 15.0 44.000 44.025 39.938 40.000
ZSM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
ZSM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.025 40.125
ZSM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
ZSM-4044-47 40.0 44.0 47.0 44.000 44.025 39.938 40.000
ZSM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
ZSM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
ZSM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.025 45.125
ZSM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
ZSM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
ZSM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
ZSM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
ZSM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000
ZSM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
ZSM-5055-60 50.0 55.0 60.0 55.000 55.030 49.938 50.000
ZSM-5560-60 55.0 60.0 60.0 55.025 55.125 60.000 60.030 54.926 55.000
ZSM-6065-50 60.0 65.0 50.0 65.000 65.030 59.926 60.000
60.025 60.125
ZSM-6065-60 60.0 65.0 60.0 65.000 65.030 59.926 60.000
ZSM-6570-34 65.0 70.0 34.0 65.025 65.125 70.000 70.030 64.926 65.000
ZSM-7075-70 70.0 75.0 70.0 70.025 70.125 75.000 75.030 69.926 70.000
ZSM-7580-50 75.0 80.0 50.0 75.025 75.125 80.000 80.030 74.926 75.000
ZSM-8085-60 80.0 85.0 60.0 85.000 85.030 79.926 80.000
80.025 80.125
ZSM-8085-80 80.0 85.0 80.0 85.000 85.030 79.926 80.000
ZSM-8590-60 85.0 90.0 60.0 85.025 85.125 90.000 90.030 84.913 85.000
ZSM-8590-100 85.0 90.0 100.0 85.025 85.125 90.000 90.030 84.913 85.000
ZSM-95100-60 95.0 100.0 60.0 95.025 95.125 100.000 100.030 94.913 95.000
30°
Z F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 347
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
ZFM-0405-04 4.0 5.5 9.5 4.0 0.75 5.500 5.512 3.970 4.000
4.010 4.058
ZFM-0405-06 4.0 5.5 9.5 6.0 0.75 5.500 5.512 3.970 4.000
ZFM-0507-05 5.0 7.0 11.0 5.0 1.00 5.010 5.058 7.000 7.015 4.970 5.000
ZFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
6.010 6.058
ZFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
ZFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
ZFM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
8.013 8.071
ZFM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
ZFM-081016-12 8.0 10.0 16.0 12.0 1.0 10.000 10.015 7.964 8.000
ZFM-091117-20 9.0 11.0 17.0 20.0 0.5 9.013 9.071 11.000 11.015 9.964 9.000
ZFM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
ZFM-1012-055 10.0 12.0 18.0 5.5 1.0 12.000 12.018 9.964 10.000
ZFM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
ZFM-1012-09 10.0 12.0 18.0 9.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
ZFM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
ZFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
ZFM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
ZFM-101315-05 10.0 13.0 15.0 5.5 1.5 10.013 10.071 13.000 13.018 9.964 10.000
ZFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
ZFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
ZFM-1214-10 12.0 14.0 20.0 10.0 1.0 14.000 14.018 11.957 12.000
ZFM-1214-12 12.0 14.0 20.0 12.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
ZFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
ZFM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
ZFM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
ZFM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
ZFM-1416-16 14.0 16.0 22.0 16.0 1.0 14.016 14.086 16.000 16.018 13.957 14.000
ZFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
ZFM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
ZFM-1517-11 15.0 17.0 23.0 11.0 1.0 17.000 17.018 14.957 15.000
ZFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
15.016 15.086
ZFM-1517-15 15.0 17.0 23.0 15.0 1.0 17.000 17.018 14.957 15.000
ZFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
ZFM-151723-23 15.0 17.0 23.0 23.0 1.0 17.000 17.018 14.957 15.000
ZFM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
ZFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
ZFM-1820-04 18.0 20.0 26.0 4.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 347
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
ZFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
ZFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
ZFM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
ZFM-1822-22 18.0 22.0 26.0 22.0 1.0 18.016 18.086 22.000 22.021 17.957 18.000
ZFM-2022-21 20.0 22.0 30.0 21.0 1.5 20.020 20.104 22.000 22.040 19.948 20.000
ZFM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
ZFM-2023-155 20.0 23.0 30.0 15.5 1.5 23.000 23.021 19.948 20.000
ZFM-2023-16 20.0 23.0 30.0 16.0 1.5 20.020 20.104 23.000 23.021 19.948 20.000
ZFM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
ZFM-2023-31 20.0 23.0 30.0 31.5 1.5 23.000 23.021 19.948 20.000
ZFM-2528-11 25.0 28.0 35.0 11.0 1.5 28.000 28.021 24.948 25.000
ZFM-2528-16 25.0 28.0 35.0 16.5 1.5 28.000 28.021 24.948 25.000
25.020 25.104
ZFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
ZFM-2528-31 25.0 28.0 35.0 31.5 1.5 28.000 28.021 24.948 25.000
ZFM-3034-13 30.0 34.0 42.0 13.0 2.0 34.000 34.025 29.948 30.000
ZFM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
ZFM-3034-20 30.0 34.0 42.0 20.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000
ZFM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
ZFM-3034-37 30.0 34.0 42.0 37.0 2.0 34.000 34.025 29.948 30.000
ZFM-3539-14 35.0 39.0 47.0 14.0 2.0 39.000 39.025 34.938 35.000
ZFM-3539-16 35.0 39.0 47.0 16.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000
ZFM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
ZFM-4044-20 40.0 44.0 52.0 20.0 2.0 44.000 44.025 39.938 40.000
ZFM-4044-30 40.0 44.0 52.0 30.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
ZFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
ZFM-4550-20 45.0 50.0 58.0 20.0 2.0 50.000 50.025 44.938 45.000
45.025 45.125
ZFM-4550-50 45.0 50.0 58.0 50.0 2.0 50.000 50.025 44.938 45.000
ZFM-5055-20 50.0 55.0 63.0 20.0 2.0 55.000 55.030 49.938 50.000
50.025 50.125
ZFM-5055-50 50.0 55.0 63.0 50.0 2.0 55.000 55.030 49.938 50.000
ZFM-6065-50 60.0 65.0 73.0 50.0 2.5 60.030 60.150 65.000 65.030 59.926 60.000
ZFM-7075-50 70.0 75.0 83.0 50.0 2.5 70.030 70.150 75.000 75.030 69.926 70.000
ZFM-7580-50 75.0 80.0 88.0 50.0 2.5 75.030 75.150 80.000 80.030 74.926 75.000
iglide®
Z iglide® Z - Product Range
Thrust washer - Metric d4
d5
d1
Type Dimensions
S
Order key
d2 Z T M -26 44- 015
d6
Thickness s (mm)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part number d1 d2 s d4 d5 h d6
h
-0.12 +0.375 +0.2
+0.25 -0.25 -0.05 +0.12
+0.12 +0.125 -0.2
iglide® UW500
• For underwater use at high temperatures
• For fast and constant movements
• High chemical resistance
357
iglide®
UW500 iglide® UW500 - For hot liquids
For fast and constant movements
For underwater use iglide® UW500 was developed for underwater applications
at high temperatures at temperatures up to 482°F. In addition, the bearings will
run in chemicals which would act as a lubricant.
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 2,320,600 DIN 53457
Tensile strength at 68°F psi 37,710 DIN 53452
Compressive strength psi 20,305
Permissible static surface pressure (68°F) psi 20,305
Shore D-hardness 86 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 109 DIN IEC 93
Surface resistance Ω < 109 DIN 53482
Compressive Strength 15
Pressure (psi)
140°F 73°F
Deformation under load and temperature
1,450
➤ Surface speed, Page 64
➤ pv value, Page 65
145
Pressure (psi)
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures
iglide® UW500 can be used in applications with permanent temperatures 160
of +482 °F. At temperatures over +302 °F an additional axial securing is 140
required. 120
100
➤ Application temperatures, Page 67
80
60
Pressure (psi)
40
20
0
68 122 176 248 302 392 482
Temperature (°F)
0.5 0.7
0.6
0.4
0.5
Coefficient of friction (µ)
Coefficient of friction (µ)
0.4
0.3
0.3
0.2
0.2
0.1
0.0
0.1 0 1,450 2,901 4,351 5,802 7,252 8,702 10,150 11,600
9.84 19.69 29.53 39.37 49.21 59.06
Pressure (psi)
Surface speed (fpm)
Coefficients of friction of iglide® UW500 as a function Coefficients of friction of iglide® UW500 as a function
of the running speed; p = 109 psi of the load, v = 1.96 fpm
Wear (µm/km)
60
40
20
0
0 145 290 435 580 725 870 1015 1160 1305 1450
Pressure (psi)
Rotating Oscillating
30 24
25 20
Hard anodized aluminum
16
20
1050, hard chromed
12
15
HR Carbon Steel
Automatic steel
Wear (µm/km)
304 Stainless
8
Wear (µm/km)
10
4
5
440B
1050
0
0 0 72 145 217 290
Pressure (psi)
Chemical Resistance
0.16
applications. 0.02
0.00
➤ Chemical table, Page 1364 0.0 0.1 0.2 0.3 0.4 0.5
Radiation Resistance
Plain bearings of iglide® UW500 are resistant up to a radiation intensity of 1 · 105 Gy. They resist to hard gamma radiation (1,000 Mrad) and
alpha or beta radiation (10,000 Mrad).
UV-Resistance
iglide® UW500 bearings are permanently resistant to UV radiation.
Vacuum
Also in vacuum atmosphere, iglide® UW500 bearings can be used almost without restrictions. Outgassing only takes place to a minor
degree.
Underwater –
iglide® H370 l Self-lubricating and maintenance-free
➤ Page 389 l Lightweight
l Good price/performance ratio
l Predictable service life
Up to 482°F, wear-resistant –
iglide® C500
➤ Page 403
Low-cost –
iglide® H2
➤ Page 411
max. +482 °F
min. –148 °F
5 materials
Ø 2 to 70 mm
mm
more dimensions on request
Enormous cost savings with high service life, as well as corrosion In this form, fill and seal machine, various iglide® self-lubricating
resistance make iglide® bearings perfect for this application. bearings are utilized.
Plastic bearings installed into the boring bar dampen vibrations and Many iglide® plain bearings are used in this gripper, making it
reduce clearance. possible to avoid damaging product thanks to smooth movement.
This bottle-filling system for a variety of liquid viscosities works Corrosion resistant iglide® bearings used in this meat roller are
quickly and precisely, thanks to numerous igus® products. resistant to the aggressive cleaning agents used.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® H l l l l
iglide® H1 l l l l l l
iglide® H370 l l l
iglide® C500 l l l l
iglide® H2 l l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® H l l l l
iglide® H1 l l l l
iglide® H370 l l l l
iglide® C500 l l l l l
iglide® H2 l l l l
iglide® H 369
iglide® H1 377
iglide® H2 411
iglide® H 3 5 369
iglide® H1 7 3 377
iglide® H2 6 7 411
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
369
iglide®
H iglide® H - Universal
High temperature and chemical resistance
Maintenance-free
Resistant to chemicals
Mechanical Properties
Modulus of elasticity psi 1,813,000 DIN 53457
Tensile strength at 68°F psi 25,380 DIN 53452
Compressive strength psi 11,750
Permissible static surface pressure (68°F) psi 13,050
Shore D-hardness 87 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 105 DIN IEC 93
Surface resistance Ω < 102 DIN 53482
3.0
The graph shows the elastic deformation of iglide® H for radial loads. At
2.5
the recommended surface pressure of 13,050 psi, the deformation is
approximately 2.5% at room temperature. 2.0
1.5
Deformation (%)
0.5
0.0
0 3,626 7,252 10,880 14,500
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
iglide® H is suitable for continuous running speeds of 196 fpm (rotating)
to 590 fpm (linear). Linear movements allow higher running speeds since
1,450 a larger area of the shaft contributes to cooling.
1.45
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Permissible pv value for iglide ® H running dry against a steel
shaft, at 68°F Rotating 196 295
Oscillating 137 216
Linear 590 787
Temperatures 23,210
iglide ® H is an extremely temperature-resistant material. With a 20,310
maximum permissible short-term temperature of 464°F, iglide® H plain 17,400
bearings may be used in applications with high heat at low loads. 14,500
With increasing temperatures, the compressive strength of iglide ® 11,600
Pressure (psi)
H plain bearings decreases. The graph to the right shows this 8,702
relationship. The ambient temperatures prevalent in the bearing
5,802
system also have an effect on the bearing wear.
2,901
0
➤ Application temperatures, Page 67 68 122 176 248 302 392
Temperature (°F)
0.15
0.3
Coefficient of friction (µ)
Coefficient of friction (µ)
0.10
0.2
0.05
0.1 0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90 78.74 0 1450 2901 4351 5802 7252 8702 10150 11600
Shaft Materials 45
40
The graphs show results of testing different shaft materials with plain
35
bearings made of iglide® H. The results clearly show that in rotating
30
and oscillating applications the correct shaft selection is critical.
25
For rotating applications, shafts made of 1050 hardened, ground steel
20
and HR Carbon steel show the best wear values, the 304 stainless
15
Wear (µm/km)
steel shaft is best suited for oscillating movements. Also, hard
chromed shafts with iglide® H bearings are only recommended for low 10
loads. If the shaft material you plan to use is not contained in this list, 5
please contact us. 0
1050 Hard 304 Stainless HR carbon
steel chromed steel steel
➤ Shaft Materials, Page 71
Oscillating Rotating
5
18
4
15
3
Hard anodized aluminum
12
Wear (µm/km) 2
1050, hard chromed
HR Carbon Steel
9
1
304 Stainless
Wear (µm/km)
6
0
0 145 290 435 580 725
440B
3
1050
Pressure (psi)
0
1050 Steel HR carbon steel 304 Stainless Hard chromed
Radiation Resistance
iglide® H plain bearings are resistant to radiation up to an intensity of 2 x 102 Gy. They also withstand neutron and gamma particle radiation.
UV Resistance
iglide® H plain bearings are only conditionally resistant against UV radiation. Under the effects of weathering, the surface of iglide® H becomes
rougher, and the compressive strength of the material decreases.
Vacuum
For use in a vacuum environment, it must be taken into account that a small amount of moisture is released as vapor.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
HSM-0304-03 3.0 4.5 3.0 3.006 3.046 4.500 4.512 2.975 3.000
HSM-0405-04 4.0 5.5 4.0 4.010 4.058 5.500 5.512 3.970 4.000
HSM-0507-05 5.0 7.0 5.0 5.010 5.058 7.000 7.015 4.970 5.000
HSM-0608-03 6.0 8.0 3.0 8.000 8.015 5.970 6.000
6.010 6.058
HSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
HSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
8.013 8.071
HSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
HSM-1012-06 10.0 12.0 6.0 12.000 12.018 9.964 10.000
10.013 10.071
HSM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
HSM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
HSM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
12.016 12.086
HSM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
HSM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
HSM-1416-20 14.0 16.0 20.0 14.016 14.086 16.000 16.018 13.957 14.000
HSM-1517-15 15.0 17.0 15.0 15.016 15.086 17.000 17.018 14.957 15.000
HSM-1618-15 16.0 18.0 15.0 18.000 18.018 15.957 16.000
HSM-1618-20 16.0 18.0 20.0 16.016 16.086 18.000 18.018 15.957 16.000
HSM-1618-25 16.0 18.0 25.0 18.000 18.018 15.957 16.000
HSM-1820-15 18.0 20.0 15.0 20.000 20.021 17.957 18.000
18.016 18.086
HSM-1820-25 18.0 20.0 25.0 20.000 20.021 17.957 18.000
HSM-2023-20 20.0 23.0 20.0 23.000 23.021 19.948 20.000
20.020 20.104
HSM-2023-30 20.0 23.0 30.0 23.000 23.021 19.948 20.000
HSM-2225-20 22.0 25.0 20.0 22.020 22.104 25.000 25.021 21.948 22.000
HSM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
25.020 25.104
HSM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000
HSM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
HSM-3034-30 30.0 34.0 30.0 30.020 30.104 34.000 34.025 29.948 30.000
HSM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
HSM-3236-30 32.0 36.0 30.0 32.025 32.125 36.000 36.025 31.938 32.000
HSM-3539-40 35.0 39.0 40.0 35.025 35.125 39.000 39.025 34.938 35.000
HSM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
40.025 40.125
HSM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
HSM-4550-30 45.0 50.0 30.0 45.025 45.125 50.000 50.025 44.938 45.000
HSM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000
HSM-5560-26 55.0 60.0 26.0 55.030 55.150 60.000 60.030 54.926 55.000
HSM-6065-60 60.0 65.0 60.0 60.030 60.150 65.000 65.030 59.926 60.000
HSM-7075-50 70.0 75.0 50.0 70.030 70.150 75.000 75.030 69.926 70.000
30°
H F M -03 04-05
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 373
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
HFM-0405-04 4.0 5.5 9.5 4.0 0.75 4.010 4.058 5.500 5.512 3.970 4.000
HFM-0507-05 5.0 7.0 11.0 5.0 1.0 7.000 7.015 4.970 5.000
5.010 5.058
HFM-0507-08 5.0 7.0 11.0 8.0 1.0 7.000 7.015 4.970 5.000
HFM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
HFM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
HFM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
HFM-0810-07 8.0 10.0 15.0 7.0 1.0 10.000 10.018 7.964 8.000
HFM-0810-10 8.0 10.0 15.0 10.0 1.0 8.013 8.071 10.000 10.018 7.964 8.000
HFM-0810-15 8.0 10.0 15.0 15.0 1.0 10.000 10.018 7.964 8.000
HFM-1012-04 10.0 12.0 18.0 4.0 1.0 12.000 12.018 9.964 10.000
HFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
10.013 10.071
HFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
HFM-1012-20 10.0 12.0 18.0 20.0 1.0 12.000 12.018 9.964 10.000
HFM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
HFM-1214-10 12.0 14.0 20.0 10.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
HFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
HFM-1416-12 14.0 16.0 22.0 12.0 1.0 14.016 14.086 16.000 16.018 13.957 14.000
HFM-1517-17 15.0 17.0 23.0 17.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
HFM-1618-13 16.0 18.0 24.0 13.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
HFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
HFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
HFM-2023-07 20.0 23.0 30.0 7.0 1.0 23.000 23.021 19.948 20.000
HFM-2023-16 20.0 23.0 30.0 16.5 1.5 20.020 20.104 23.000 23.021 19.948 20.000
HFM-2023-30 20.0 23.0 30.0 30.0 1.5 23.000 23.021 19.948 20.000
HFM-2528-30 25.0 28.0 35.0 30.0 1.5 25.020 25.104 28.000 28.021 24.948 25.000
HFM-2730-20 27.0 30.0 38.0 20.0 1.5 27.020 27.104 30.000 30.021 26.948 27.000
HFM-3034-40 30.0 34.0 42.0 40.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000
HFM-3438-13 34.0 38.0 46.0 13.0 2.0 34.025 34.125 38.000 38.025 33.938 34.000
HFM-3539-26 35.0 39.0 47.0 26.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000
HFM-4044-40 40.0 44.0 52.0 40.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
HFM-4550-50 45.0 50.0 58.0 50.0 2.0 45.025 45.125 50.000 50.025 44.938 45.000
HFM-5055-50 50.0 55.0 63.0 50.0 2.0 50.025 50.125 55.000 55.030 49.938 50.000
HFM-6065-50 60.0 65.0 73.0 50.0 2.0 60.030 60.150 65.000 65.030 59.926 60.000
HFM-7075-50 70.0 75.0 83.0 50.0 2.0 70.030 70.150 75.000 75.030 69.926 70.000
377
iglide®
H1 iglide® H1 - Wear resistant
Long life operation in extreme ambient conditions
High wear resistance in extreme iglide® H1 is the first choice when long life is required in
ambient conditions extreme environmental conditions. Extreme wear resistance
is coupled with excellent resistance to temperature and
chemicals - not only in the packaging and foodstuff
industries or the automotive industry.
Mechanical Properties
Modulus of elasticity psi 406,100 DIN 53457
Tensile strength at 68°F psi 7,977 DIN 53452
Compressive strength psi 11,310
Permissible static surface pressure (68°F) psi 11,600
Shore D-hardness 77 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 7
6
The graph shows the elastic deformation of iglide® H1 for radial loads.
5
Among the iglide® materials. iglide® H1 has the greatest elasticity. This
is beneficial in applications with edge loads and is the reason for the 4
higher mechanical loss factor that indicates the vibration dampening 3
Deformation (%)
capacity of a material.
2
1
➤ Compressive strength, Page 63
0
0 2901 5802 8702 11600
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
Due to the excellent coefficients of friction, rotating surface speeds up
to 393 fpm are possible with iglide® H1 plain bearings in dry operation.
1,450 Linear speeds up to 984 fpm can be achieved in continuous applications.
The speeds stated in the table are limit values for the lowest bearing
loads. With higher loads, the permitted speed drops with the extent of
an increase in load due to the limitations given by the pv value.
145
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Temperatures 11600
iglide ® H1 is an extremely temperature-resistant material. With a 10150
maximum permissible short-term temperature of 464°F, iglide ® H1 8702
plain bearings may be used in heat treated applications at low loads. 7252
With increasing temperatures, the compressive strength of iglide® H1 5802
plain bearings decreases. The graph to the right shows this relationship.
Pressure (psi)
4351
The ambient temperatures prevalent in the bearing system also have
2901
an effect on the bearing wear.
1450
0
➤ Application temperatures, Page 67
68 122 176 248 302 392
Temperature (°F)
0.25 0.20
0.20
0.15
Coefficient of friction (µ)
0.15
0.10
0.10
0.05 0.05
0.00
0.00
0 49.2 98.4 147.6 196.9 246.1 295.3 344.5 393.7
0 1450 2901 4351 5802 7252 8702 10150 11600
Surface Speed (fpm)
Pressure (psi)
Coefficients of friction for iglide® H1 as a result of the Coefficients of friction for iglide® H1 as a result of the
surface speed; p =108 psi load, v = 1.97 fpm
Shaft Materials 7
Wear (µm/km)
especially with high loads. In oscillating applications, the lowest wear 2
rates were measured with aluminum HC and 304 stainless shafts.
1
With most shafts, the rotation wear rates were somewhat lower than
the pivoting wear rates. If the shaft material you plan to use is not 0
contained in this list, please contact us. 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
1.0
0.9 3
0.8
Hard anodized aluminum
0.7 2
Automatic screw steel
0.6
Wear (µm/km)
HR Carbon Steel
0.5 1
304 Stainless
0.4
Wear (µm/km)
0.3
0
0.2
440B
0.1
Pressure (psi)
0.0
1050 Steel 304 Stainless
HR carbon steel Hard chromed
Wear of iglide H1, rotating application with different
®
shaft materials, p=108 psi, v=98 fpm Wear of iglide® H1 with different shaft materials in
rotating applications
Chemical Resistance
iglide ® H1 plain bearings have a good chemical resistance and
chemicals can even act as lubricants. Plain bearings made of iglide®
H are not resistant to hot, oxidizing acids and some other particularly
aggressive chemicals.
The moisture absorption of iglide H1 plain bearings is approximately
0.1% in standard atmosphere. The saturation limit in water is 0.3%.
Therefore, iglide® H1 is very well suited for use in wet surroundings
Medium Resistance
Alcohol +
Hydrocarbon +
Greases, oils without additives +
Fuels +
Weak acids + to 0
Strong acids + to –
Weak alkaline +
Strong alkaline + to –
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Resistant to radiation up to an intensity of 3 · 10² Gy.
UV Resistance
iglide® H1 plain bearings are only conditionally resistant against UV radiation. The surface of iglide® H1 becomes coarser and the wear
increases under the influence of atmospheric conditions.
Vacuum
Note that for use in a vacuum environment, water elements, even if only minimal, should be degassed.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
H1SM-0304-05 3.0 4.5 5.0 3.006 3.046 4.500 4.512 2.975 3.000
H1SM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
4.010 4.058
H1SM-0405-06 4.0 5.5 6.0 5.500 5.512 3.970 4.000
H1SM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
5.010 5.058
H1SM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
H1SM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
H1SM-0608-08 6.0 8.0 8.0 6.010 6.058 8.000 8.015 5.970 6.000
H1SM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
H1SM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
H1SM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
8.013 8.071
H1SM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
H1SM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
H1SM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
H1SM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
H1SM-1012-12 10.0 12.0 12.0 10.013 10.071 12.000 12.018 9.964 10.000
H1SM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
H1SM-1012-20 10.0 12.0 20.0 12.000 12.018 9.964 10.000
H1SM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
H1SM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
12.016 12.086
H1SM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
H1SM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
H1SM-1315-10 13.0 15.0 10.0 15.000 15.018 12.957 13.000
13.016 13.086
H1SM-1315-20 13.0 15.0 10.0 15.000 15.018 12.957 13.000
H1SM-1416-15 14.0 16.0 15.0 16.000 16.018 13.957 14.000
H1SM-1416-20 14.0 16.0 20.0 14.016 14.086 16.000 16.018 13.957 14.000
H1SM-1416-25 14.0 16.0 25.0 16.000 16.018 13.957 14.000
H1SM-1517-15 15.0 17.0 15.0 17.000 17.018 14.957 15.000
H1SM-1517-20 15.0 17.0 20.0 15.016 15.086 17.000 17.018 14.957 15.000
H1SM-1517-25 15.0 17.0 25.0 17.000 17.018 14.957 15.000
H1SM-1618-15 16.0 18.0 15.0 18.000 18.018 15.957 16.000
H1SM-1618-20 16.0 18.0 20.0 16.016 16.086 18.000 18.018 15.957 16.000
H1SM-1618-25 16.0 18.0 25.0 18.000 18.018 15.957 16.000
H1SM-1820-15 18.0 20.0 15.0 20.000 20.021 17.957 18.000
H1SM-1820-20 18.0 20.0 20.0 18.016 18.086 20.000 20.021 17.957 18.000
H1SM-1820-25 18.0 20.0 25.0 20.000 20.021 17.957 18.000
H1SM-2023-10 20.0 23.0 10.0 23.000 23.021 19.948 20.000
20.020 20.104
H1SM-2023-15 20.0 23.0 15.0 23.000 23.021 19.948 20.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
H1 F M -03 04-05
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r
r = max. 0.5
b2
For tolerance values
d3 please refer to page 381
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
H1FM-0304-05 3.0 4.5 7.5 5.0 0.75 3.006 3.046 4.500 4.512 2.975 3.000
H1FM-0405-04 4.0 5.5 9.5 4.0 0.75 5.500 5.512 3.970 4.000
4.010 4.058
H1FM-0405-06 4.0 5.5 9.5 6.0 0.75 5.500 5.512 3.970 4.000
H1FM-0507-05 5.0 7.0 11.0 5.0 1.00 5.010 5.058 7.000 7.015 4.970 5.000
H1FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
H1FM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
6.010 6.058
H1FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
H1FM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
H1FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
H1FM-0810-065 8.0 10.0 15.0 6.5 1.0 10.000 10.015 7.964 8.000
H1FM-0810-07 8.0 10.0 15.0 7.5 1.0 8.013 8.071 10.000 10.015 7.964 8.000
H1FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
H1FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
H1FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
H1FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
H1FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
H1FM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
H1FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
H1FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
H1FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.016 12.086
H1FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
H1FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
H1FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.016 14.086
H1FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
H1FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
H1FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
H1FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
H1FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
H1FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.016 16.086 18.000 18.018 15.957 16.000
H1FM-1618-25 16.0 18.0 24.0 25.0 1.0 18.000 18.018 15.957 16.000
H1FM-1820-04 18.0 20.0 26.0 4.0 1.0 20.000 20.021 17.957 18.000
H1FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
18.016 18.086
H1FM-1820-17 18.0 20.0 26.0 17.0 1.0 20.000 20.021 17.957 18.000
H1FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
H1FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
H1FM-2023-16 20.0 23.0 30.0 16.0 1.5 20.020 20.104 23.000 23.021 19.948 20.000
H1FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 381
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
H1FM-2023-30 20.0 23.0 30.0 30.0 1.5 20.020 20.104 23.000 23.021 19.948 20.000
H1FM-2528-11 25.0 28.0 35.0 11.0 1.5 28.000 28.021 24.948 25.000
H1FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.020 25.104 28.000 28.021 24.948 25.000
H1FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
H1FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
30.020 30.104
H1FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
H1FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.025 35.125
H1FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
H1FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.025 40.125
H1FM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
H1FM-4550-50 45.0 50.0 58.0 50.0 2.0 45.025 45.125 50.000 50.025 44.938 45.000
389
iglide®
H370 iglide® H370 - For submerged applications
For temperatures up to 392°F
Mechanical Properties
Modulus of elasticity psi 1,610,000 DIN 53457
Tensile strength at 68°F psi 19,580 DIN 53452
Compressive strength psi 11,460
Permissible static surface pressure (68°F) psi 10,880
Shore D-hardness 82 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 105 DIN IEC 93
Surface resistance Ω < 105 DIN 53482
8
Compressive Strength
7
The graph shows the elastic deformation of iglide ® H370 for radial 6
loads. At the maximum permissible load of 10,875 psi, the deformation 5
is approximately 2.5% at room temperature.
4
Deformation (%)
14,500
Permissible Surface Speeds
The maximum permissible surface speed depends on the temperature
during operation. iglide® H370 is able to run at speeds of up to 236
1,450 fpm (rotating) to 787 fpm (linear)
Temperatures 11600
10150
iglide ® H370 is an extremely temperature-resistant material. With a
8702
maximum permissible short-term temperature of 464°F, iglide® H370
7252
plain bearings may be subjected to a heat treating process without
5802
additional load. With increasing temperatures, the compressive strength
of iglide® H370 plain bearings decreases. The graph to the right shows 4351
Pressure (psi)
this relationship. 2901
The ambient temperatures prevalent in the bearing system also have 1450
an effect on the bearing wear. With increasing temperatures, the wear 0
increases. 68 122 176 248 302 392
iglide® H370 loses approximately 75% of its compressive strength when Temperature (°F)
the temperature increases from room temperature to 302°F.
On the other hand, there is little change in wear resistance at the same Recommended permissible maximum static
temperature range. surface pressure of iglide® H370 as a result of the
temperature
0.4 0.25
0.20
0.3
Coefficient of friction (µ)
0.15
0.10
0.2
0.05
0.1 0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 2,176 4,351 6,527 8,702 10,880
Coefficients of friction for iglide® H370 as a result Coefficients of friction for iglide® H370 as a result of
of the surface speed; p =108 psi the load, v =1.97 fpm
For loads up to 290 psi, A hard-chromed shaft is the best material 15.0
for iglide ® H370 in rotating applications. Note the high wear values 12.5
for 303 Stainless shafts, which have a tendency to stick-slip because 10.0
Wear (µm/km)
of their very smooth surfaces. The HR Carbon Steel shaft has better 7.5
rotational values than Cold Rolled Steel starting at 290 psi. On the 5.0
other hand, for oscillating movements, the 303 Stainless Steel shaft 2.5
has a clear superiority. As the graph shows, it produces, at 290 psi, 0.0
a lower wear by a factor of 11 than the Cold Rolled Steel shaft. For 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
iglide® H370 a ground surface with an average roughness of 8-16 rms
is recommended for the shaft. Oscillating Rotating
If the shaft material you plan to use is not contained in this list, please
Wear for oscillating and rotating applications with
contact us.
different shaft materials: p = 290 psi
8.0
7.0
6.0
Hard anodized aluminum
5.0
1050, hard chromed
4.0
HR carbon steel
304 Stainless
3.0
Wear (µm/km)
2.0
440B
1050
1.0
0.0
Radiation Resistance
iglide® H370 withstands neutron and gamma particle radiation without detectable losses to its excellent mechanical properties. Plain bearings
made from iglide® H370 are resistant to radiation up to an intensity of 2 x 102 Gy
UV-Resistance
iglide® H370 plain bearings are permanently resistant against UV radiation.
Vacuum
In a vacuum environment, moisture is released as a vapor. However, due to its low moisture absorption, use in a vacuum is possible.
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
30°
d1
For tolerance values
Inch
please refer to page 393
*Based on steel housing bore
H370SI-0203-03 1/8 3/16 3/16 .1251 .1269 .1873 .1878 .1236 .1243
H370SI-0304-04 3/16 1/4 1/4 .1873 .1892 .2497 .2503 .1858 .1865
H370SI-0405-04 1/4 5/16 1/4 .2498 .2521 .3122 .3128 .2481 .2490
H370SI-0506-06 5/16 3/8 3/8 .3125 .3148 .3747 .3753 .3106 .3115
H370SI-0607-08 3/8 15/32 1/2 .3750 .3773 .4684 .4691 .3731 .3740
H370SI-0809-08 1/2 19/32 1/2 .5003 .5030 .5934 .5941 .4980 .4990
H370SI-1011-12 5/8 23/32 3/4 .6253 .6280 .7184 .7192 .6230 .6240
H370SI-1214-12 3/4 7/8 3/4 .7505 .7541 .8747 .8755 .7479 .7491
H370SI-1416-16 7/8 1 1 .8757 .8791 .9997 1.0005 .8729 .8741
H370SI-1618-16 1 1 1/8 1 1.0007 1.0041 1.1247 1.1255 .9979 .9991
H370SI-2022-20 1 1/4 1 13/32 1 1/4 1.2508 1.2548 1.4058 1.4068 1.2472 1.2488
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
please refer to page 393
Inch
*Based on steel housing bore
H370FI-0203-03 1/8 3/16 3/16 .312 .032 .1251 .1269 .1873 .1878 .1236 .1243
H370FI-0304-04 3/16 1/4 1/4 .375 .032 .1873 .1892 .2497 .2503 .1858 .1865
H370FI-0405-04 1/4 5/16 1/4 .500 .032 .2498 .2521 .3122 .3128 .2481 .2490
H370FI-0506-06 5/16 3/8 3/8 .562 .032 .3125 .3148 .3747 .3753 .3106 .3115
H370FI-0607-08 3/8 15/32 1/2 .687 .046 .3750 .3773 .4684 .4691 .3731 .3740
H370FI-0809-08 1/2 19/32 1/2 .875 .046 .5003 .5030 .5934 .5941 .4980 .4990
H370FI-1011-12 5/8 23/32 3/4 1.000 .046 .6253 .6280 .7184 .7192 .6230 .6240
H370FI-1214-12 3/4 7/8 3/4 1.125 .062 .7505 .7541 .8747 .8755 .7479 .7491
H370FI-1416-16 7/8 1 1 1.250 .062 .8757 .8791 .9997 1.0005 .8729 .8741
H370FI-1618-16 1 1 1/8 1 1.375 .062 1.0007 1.0041 1.1247 1.1255 .9979 .9991
H370FI-2022-20 1 1/4 1 13/32 1 1/4 1.687 .078 1.2508 1.2548 1.4058 1.4068 1.2472 1.2488
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
H370SM-0304-03 3.0 4.5 3.0 3.006 3.046 4.500 4.512 2.975 3.000
H370SM-0405-04 4.0 5.5 4.0 5.500 5.512 3.970 4.000
H370SM-0405-06 4.0 5.5 6.0 4.010 4.058 5.500 5.512 3.970 4.000
H370SM-0405-12 4.0 5.5 4.0 5.500 5.512 3.970 4.000
H370SM-0507-05 5.0 7.0 5.0 7.000 7.015 4.970 5.000
5.010 5.058
H370SM-0507-10 5.0 7.0 10.0 7.000 7.015 4.970 5.000
H370SM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000
H370SM-0608-08 6.0 8.0 8.0 6.010 6.058 8.000 8.015 5.970 6.000
H370SM-0608-10 6.0 8.0 10.0 8.000 8.015 5.970 6.000
H370SM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
H370SM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
8.013 8.071
H370SM-0810-12 8.0 10.0 12.0 10.000 10.015 7.964 8.000
H370SM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
H370SM-1012-08 10.0 12.0 8.0 12.000 12.018 9.964 10.000
H370SM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
H370SM-1012-12 10.0 12.0 12.0 10.013 10.071 12.000 12.018 9.964 10.000
H370SM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
H370SM-1012-20 10.0 12.0 20.0 12.000 12.018 9.964 10.000
H370SM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
H370SM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000
12.016 12.086
H370SM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
H370SM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
H370SM-1315-10 13.0 15.0 10.0 15.000 15.018 12.957 13.000
13.016 13.086
H370SM-1315-20 13.0 15.0 20.0 15.000 15.018 12.957 13.000
H370SM-1416-15 14.0 16.0 15.0 16.000 16.018 13.957 14.000
H370SM-1416-20 14.0 16.0 20.0 14.016 14.086 16.000 16.018 13.957 14.000
H370SM-1416-25 14.0 16.0 25.0 16.000 16.018 13.957 14.000
H370SM-1517-15 15.0 17.0 15.0 17.000 17.018 14.957 15.000
H370SM-1517-20 15.0 17.0 20.0 15.016 15.086 17.000 17.018 14.957 15.000
H370SM-1517-25 15.0 17.0 25.0 17.000 17.018 14.957 15.000
H370SM-1618-15 16.0 18.0 15.0 18.000 18.018 15.957 16.000
H370SM-1618-20 16.0 18.0 20.0 16.016 16.086 18.000 18.018 15.957 16.000
H370SM-1618-25 16.0 18.0 25.0 18.000 18.018 15.957 16.000
H370SM-1820-15 18.0 20.0 15.0 20.000 20.021 17.957 18.000
H370SM-1820-20 18.0 20.0 20.0 18.016 18.086 20.000 20.021 17.957 18.000
H370SM-1820-25 18.0 20.0 25.0 20.000 20.021 17.957 18.000
H370SM-2023-10 20.0 23.0 10.0 20.020 20.104 23.000 23.021 19.948 20.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
H370SM-4550-50 45.0 50.0 50.0 45.025 45.125 50.000 50.025 44.938 45.000
H370SM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
H370SM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
H370SM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000
H370SM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
H370SM-5055-60 50.0 55.0 60.0 55.000 55.030 49.938 50.000
H370SM-5560-26 55.0 60.0 26.0 55.030 55.150 60.000 60.030 54.926 55.000
H370SM-6065-60 60.0 65.0 60.0 60.030 60.150 65.000 65.030 59.926 60.000
H370SM-7580-60 75.0 80.0 60.0 75.030 75.150 80.000 80.030 74.926 75.000
30°
H370 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
H370FM-0405-04 4.0 5.5 9.5 4.0 0.75 4.010 4.058 5.500 5.512 3.970 4.000
H370FM-0507-05 5.0 7.0 11.0 5.0 1.0 5.010 5.058 7.000 7.015 4.970 5.000
H370FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
H370FM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
6.010 6.058
H370FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
H370FM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000
H370FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.018 7.964 8.000
H370FM-0810-06 8.0 10.0 15.0 6.0 1.0 10.000 10.018 7.964 8.000
H370FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.018 7.964 8.000
8.013 8.071
H370FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.018 7.964 8.000
H370FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.018 7.964 8.000
H370FM-0810-15 8.0 10.0 15.0 15.0 1.0 10.000 10.018 7.964 8.000
H370FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
H370FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
H370FM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
H370FM-1012-12 10.0 12.0 18.0 12.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
H370FM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
H370FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
H370FM-1012-20 10.0 12.0 18.0 20.0 1.0 12.000 12.018 9.964 10.000
H370FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
H370FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
H370FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
12.016 12.086
H370FM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000
H370FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
H370FM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
H370FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.016 14.086
H370FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
H370FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
H370FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
H370FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
H370FM-1618-10 16.0 18.0 24.0 10.0 1.0 18.000 18.018 15.957 16.000
H370FM-1618-12 16.0 18.0 24.0 12.0 1.0 16.016 16.086 18.000 18.018 15.957 16.000
H370FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
H370FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
18.016 18.086
H370FM-1820-17 18.0 20.0 26.0 17.0 1.0 20.000 20.021 17.957 18.000
H370FM-1820-22 18.0 20.0 26.0 22.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
H370FM-2023-11 20.0 23.0 30.0 11.5 1.5 20.020 20.104 23.000 23.021 19.948 20.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 393
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
H370FM-2023-16 20.0 23.0 30.0 16.5 1.5 23.000 23.021 19.948 20.000
H370FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.020 20.104 23.000 23.021 19.948 20.000
H370FM-2023-30 20.0 23.0 30.0 30.0 1.5 23.000 23.021 19.948 20.000
H370FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
H370FM-2528-16 25.0 28.0 35.0 16.5 1.5 28.000 28.021 24.948 25.000
25.020 25.104
H370FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
H370FM-2528-30 25.0 28.0 35.0 30.0 1.5 28.000 28.021 24.948 25.000
H370FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
H370FM-3034-26 30.0 34.0 42.0 26.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000
H370FM-3034-40 30.0 34.0 42.0 40.0 2.0 34.000 34.025 29.948 30.000
H370FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.025 35.125
H370FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
H370FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.025 40.125
H370FM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
H370FM-4550-50 45.0 50.0 58.0 50.0 2.0 45.025 45.125 50.000 50.025 44.938 45.000
H370FM-5055-50 50.0 55.0 63.0 50.0 2.0 50.025 50.125 55.000 55.030 49.938 50.000
H370FM-6065-50 60.0 65.0 73.0 50.0 2.0 60.030 60.150 65.000 65.030 59.926 60.000
H370FM-7075-50 70.0 75.0 83.0 50.0 2.0 70.030 70.150 75.000 75.030 69.926 70.000
psi
iglide® C500
• High resistance to media and temperatures
• Resistant to steam
• Good coefficients of friction and wear
403
iglide®
C500 iglide® C500 - Up to 482°F, wear-resistant
High resistance to media and temperatures
Self-lubricating and
maintenance-free
Mechanical Properties
Modulus of elasticity psi 435,110 DIN 53457
Tensile strength at 68°F psi 14,500 DIN 53452
Compressive strength psi 15,950
Permissible static surface pressure (68°F) psi 15,950
Shore D-hardness 81 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1014 DIN IEC 93
Surface resistance Ω > 1013 DIN 53482
Compressive Strength 10
9
With increasing temperatures, the compressive strength of iglide® C500 8
plain bearings decreases. The graph shows this inverse relationship. 7
However, at an operation temperature of +392 °F the permissible surface 6
pressure is close to 2,901 psi. The recommended maximum surface 5
Deformation (%)
140°F 73°F
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures
iglide® C500 belongs to the most temperature resistant iglide® materials. 17,400
Similar to all thermoplastics, with increasing temperatures, the compressive
14,500
strength of iglide® C500 bearings decreases. The ambient temperatures
prevalent in the bearing system also have an effect on the bearing wear. The 11,600
wear rises with increasing temperatures. At temperatures over +266 °F an
8,702
additional securing is required.
Pressure (psi)
5,802
➤ Application temperatures, Page 67
2,901
0
68 122 176 248 302 392
iglide C500 ® Application Temperature
Minimum -148°F Temperature (°F)
Max. long-term +482°F Recommended maximum permissible static surface
Max. short-term +572°F pressure of iglide® C500 as a result of the temperature
0.30 0.35
0.25 0.30
0.25
0.20
Coefficient of friction (µ)
0.20
0.15
0.15
0.10
0.10
0.05 0.05
0.00 0.00
19.69 29.53 39.37 49.21 59.06 68.90 78.74 0 1,450 2,901 4,351 5,802 7,252 8,702 10,150 11,600
Pressure (psi)
Surface speed (fpm)
Coefficients of friction of iglide® C500 as a function Coefficients of friction of iglide® C500 as a function
of the running speed; p = 145 psi of the load, v = 1.96 fpm
Wear (µm/km)
characteristics across a variety of shaft types. This wear rate spikes upward 60
40
in combination with free-machining steel, and, notably so, spikes downward
20
in combination with HC aluminum. 0
The wear under rotational loads is higher, specifically with increasing radial 0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
loads as compared to pivoting motions. Pressure (psi)
Rotating Oscillating
4
Hard anodized aluminum
3
1050, hard chromed
HR Carbon Steel
Automatic steel
2
304 Stainless
Wear (µm/km)
1
440B
1050
30°
>18 to 30 -0 /-330
Length of chamfer Length >30 to 50 -0 /-390
>50 to 80 -0 /-460
Chemical Resistance
0.10
iglide® C500 bearings have a very good resistance against chemicals.
0.08
Most organic and inorganic acids, alkaline solutions or lubricants do
Radiation Resistance
iglide® C500 withstands neutron and gamma particle radiation without detectable losses of its excellent mechanical properties. Plain bearings
made from iglide® C500 are resistant to radiation up to an intensity of 3 · 102 Gy.
UV-Resistance
iglide® C500 plain bearings are permanently resistant to UV radiation.
Vacuum
iglide® C500 plain bearings outgas in a vacuum. Due to its low moisture absorption, use in a vacuum is possible.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
C500SM-0608-06 6.0 8.0 6.0 6.010 6.058 8.000 8.015 5.970 6.000
C500SM-0810-10 8.0 10.0 10.0 8.013 8.071 10.000 10.015 7.964 8.000
C500SM-1012-10 10.0 12.0 10.0 10.013 10.071 12.000 12.018 9.964 10.000
C500SM-1214-12 12.0 14.0 12.0 12.016 12.086 14.000 14.018 11.957 12.000
C500SM-1618-15 16.0 18.0 15.0 16.016 16.086 18.000 18.018 15.957 16.000
C500SM-2023-20 20.0 23.0 20.0 20.020 20.104 23.000 23.021 19.948 20.000
C500SM-4044-30 40.0 44.0 30.0 40.025 40.125 44.000 44.025 39.938 40.000
Outer-Ø d2 (mm)
f
Inner-Ø d1 (mm)
Length b1 (mm)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
Metric
please refer to page 407
*Based on steel housing bore
C500FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
C500FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.013 8.071 10.000 10.015 9.964 10.000
C500FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
C500FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
C500FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.016 16.086 18.000 18.018 15.957 16.000
C500FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.020 20.104 23.000 23.021 20.948 21.000
411
iglide®
H2 iglide® H2 - Low-cost
For high temperatures
Cost-effective
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 1,494,000 DIN 53457
Tensile strength at 68°F psi 30,460 DIN 53452
Compressive strength psi 15,810
Permissible static surface pressure (68°F) psi 15,950
Shore D-hardness 88 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 1015 DIN IEC 93
Surface resistance Ω < 1014 DIN 53482
Compressive Strength 6
5
The graph shows the elastic deformation of iglide® H2 for radial loads. At
the permissible static surface pressure of 15,950 psi, the deformation is 4
below 3% at room temperature. The values for tensile and compressive
3
strength are higher than those of iglide® H at room temperature.
Deformation (%)
2
➤ Compressive strength, Page 63
1
0
0 2901 5802 8702 11600 14500
1450 4351 7252 10150 13050 15950
Pressure (psi)
140°F 73°F
Deformation under load and temperature
145,000
Permissible Surface Speeds
In the development of iglide® H2 cost considerations and mechanical
14,500 resistance were the main issues. The permissible surface speeds of
these bearings are rather low, which limits the use to primarily slow
movements or intermittent operations.
1,450
14.5
.197 1.97 19.7 197 1,969
Temperatures 23,210
iglide® H2 is a material with an extremely high resistance to temperature. 20,310
The maximum permissible short-term temperature of 464°F. iglide® H2 17,400
plain bearings may be used in heat treated applications at low loads. 14,500
With increasing temperatures, the compressive strength of iglide® H2 11,600
plain bearings decreases at a greater rate than that of iglide® H. The
Pressure (psi)
8,702
graph to the right shows this relationship.
5,802
2,901
➤ Application temperatures, Page 67
0
68 122 176 248 302 392
Temperature (°F)
0.4 0.30
0.25
0.3 0.20
Coefficient of friction (µ)
0.15
0.2 0.10
0.05
0.1 0.00
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 1450 2901 4351 5802 7252 8702 10150 11600
When studying the wear resistance of iglide® H2, it must be repeated 125
that these bearings have been developed for high static temperature
100
resistance. The wear resistance does not compare with the values of
iglide® H370 for any bearing/shaft combination. 75
iglide® H2 bearings should not be combined with hard chromed shafts.
Shafts made from 1050 hardened and ground steel and 303 stainless 50
Wear (µm/km)
are significantly better, as shown in the graphs.
25
If you wish to use shaft materials that are not listed please contact us.
The results for other shaft/bearing combinations are often available. 0
1050 Hard 304 Stainless HR carbon
➤ Shaft Materials, Page 71 steel chromed steel steel
Oscillating Rotating
Wear for oscillating and rotating applications with dif-
ferent shaft materials; p = 290 psi
100
25.0 80
20.0 60
Hard anodized aluminum
15.0 40
Wear (µm/km)
HR Carbon Steel
20
304 Stainless
10.0
Wear (µm/km)
0
5.0 14.5 36 108 145 290 725
440B
1050
Pressure (psi)
0.0
1050 steel 304 Stainless
HR carbon steel Hard chromed
Wear of iglide® H2, rotating application with different
shaft materials, p = 108 psi, v = 98 fpm Wear of iglide® H2 with different shaft materials in
rotating applications
Radiation Resistance
iglide® H2 plain bearings withstands neutron and gamma particle radiation without detectable losses of its excellent mechanical properties. Plain
bearings made of iglide® H2 are resistant to radiation up to an intensity of 2 x 102 Gy.
UV Resistance
iglide ® H2 plain bearings change under the influence of UV radiation and other weathering effects. The surface becomes rougher and the
compressive strength decreases. The use of iglide® H2 in applications that are permanently exposed to weathering should be tested.
Vacuum
In a vacuum environment, small moisture components are released as vapor. It is possible to use iglide® H2 in a vacuum.
FDA-compliant general
purpose material – Contact with food
iglide® A180
➤ Page 423 iglide® bearings perform well without external lubrication,
including in enviroments where high levels of hygiene are
required.
The food grade material, compliant
with FDA specifications and EC The specialists group of bearing materials is made up of
Directive 10/2011 EC – iglide® A181 FDA-compliant materials for a wide range of operating
➤ Page 431 conditions including temperature and moisture variants,
including iglide® T220, which is even suitable for the
tobacco industry.
Robust –
iglide® A290 9 materials
➤ Page 479
iglide® bearings proved ideal, as they are cost effective and need no Self-lubricating plastic plain bearings and igubal® spherical
external lubrication. bearings maximize application service life, and eliminate downtime
when paired with stainless steel.
Complete freedom from maintenance in extremely dirty applications FDA-compliant iglide® A500 bearings are resilient in high-
distinguishes iglide® bearings from the competition. temperature applications, including in cooking oil up to 428°F.
In this meat slicer application that makes direct food contact, Components in this brewery equipment must satisfy a variety of
bearings which require external lubrication cannot be used. requirements, including temperature resistance.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® A180 l l l l l
iglide® A181 l l l l
iglide® A200 l l
iglide® A350 l l l l l
iglide® A500 l l l
iglide® A160 l l l
iglide® A290 l l
iglide® UW160 l l l
iglide® T220 l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® A180 l l l l l
iglide® A181 l l l l l
iglide® A200 l l l
iglide® A350 l l l l l l
iglide® A500 l l l l l l
iglide® A160 l l l
iglide® A290 l
iglide® UW160 l l l l
iglide® T220 l l
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
423
iglide®
A180
iglide® A180 - FDA general purpose
FDA compliant general purpose material
FDA compliant material for applications with low to
Complies with FDA regulations for medium loads in environments (or contact) with food or
repeated contact with food drugs as well as humidity.
iglide® A180 material complies with EC Directive 10/2011 EC and also with FDA
(Food and Drug Administration) specifications for repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 333,600 DIN 53457
Tensile strength at 68°F psi 12,760 DIN 53452
Compressive strength psi 11,310
Permissible static surface pressure (68°F) psi 4,060
Shore D-hardness 76 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 15
The graph at the right shows the elastic deformation of iglide® A180
Deformation in %
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Temperatures
4351
The short-term permitted maximum temperature is +230 °F. With
increasing temperatures, the compressive strength of iglide ® A180 3626
bearings decreases. The graph at the right shows this relationship. 2091
The temperatures prevalent in the bearing system also have an effect
on the bearing wear. 2176
Pressure (psi)
1450
➤ Application temperatures, Page 67
725
0
68 86 104 122 140 158 176 194
iglide A180
® Application Temperature
Minimum -58°F Temperature in °F
0.6 0.3
0.5
Coefficient of friction (µ)
0.4 0.2
Coefficient of friction (µ)
0.3
0.2 0.1
0.1
0.0 0.0
9.84 19.69 29.53 39.37 49.22 59.05 68.90 78.74 0 725 1450 2175 2900 3626 4351
Load (psi)
Surface Speed (fpm)
Coefficients of friction of iglide A180 as a function of ® Coefficients of friction of iglide® A180 as a function of
the running speed; p = 108 psi the load, v = 1.96 fpm
Shaft Materials 20
The graphs show the test results of iglide ® A180 bearings running
against various shaft materials. 15
Wear (µm/km)
With Hard chromed shafts, the higher wear in pivoting applications is 5
exemplary compared to rotating applications. The graph to the right
clearly shows, in the example of the 304 stainless shafts, the direct
0
increase in wear with rising load with “soft” shafts. The increase is 36 108 290 725 1450 2900
hardly noticeable with hard shafts.
Pressure (psi)
3.5 18.0
3.0
3.0 2.1
Hard anodized aluminum
2.5 1.8
Automatic screw steel
1.5
1050, hard chromed
2.0 1.2
HR Carbon Steel
0.9
Wear (µm/km)
1.5
304 Stainless
Wear (µm/km)
0.6
440B Steel
1050 Steel
1.0 0.3
0.0
0.5 36 108 145 290
0.10
Medium Resistance
0.09
Radiation Resistance
Plain bearings made of iglide® A180 are resistant to radiation up to an intensity of 3 · 102 Gy. Higher radiation levels attack the material and can
cause the loss of essential mechanical properties.
UV-Resistance
iglide® A180 bearings are resistant to UV radiation, but the tribological properties deteriorate with continuous exposure.
Vacuum
When used in a vacuum environment, the iglide® A180 plain bearings release moisture as a vapor. Therefore, only dehumidified bearings are
suitable in a vacuum environment.
iglide® A180
Electrical Properties Specific volume resistance > 1012 Ωcm
iglide A180 plain bearings are electrically insulating.
®
Surface resistance > 1011 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A180SM-0608-10 6.0 8.0 10.0 6.020 6.068 8.000 8.015 5.970 6.000
A180SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
A180SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
A180SM-1214-15 12.0 14.0 15.0 12.032 12.102 14.000 14.018 11.957 12.000
A180SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
A180SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
A180SM-2528-30 25.0 28.0 20.0 25.040 25.124 28.000 28.021 24.948 25.000
A180SM-3034-20 30.0 34.0 20.0 30.040 30.124 34.000 34.025 29.948 30.000
30°
A180 F M -06 08-06
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
A180FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.012 5.970 6.000
A180FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
A180FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
A180FM-1214-15 12.0 14.0 20.0 15.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
A180FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
A180FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
A180FM-2528-21 25.0 28.0 35.0 21.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
A180FM-3034-26 30.0 34.0 42.0 26.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
431
iglide®
A181
iglide® A181 - FDA and EC Directive compliant
Food grade material
Compliant with EC Directive Bearings made of iglide® A181 are suitable for application
10/2011 EC in direct contact with food. Therefore, they are the ideal
solution for bearing applications on machines for the
food and packaging industries, medical equipment
manufacturing, and for small equipment for households,
etc. The blue color also facilitates the often required
Compliant with FDA regulations “optical detectability” in the food industry.
iglide® A181 material complies with EC Directive 10/2011 EC and also with FDA
(Food and Drug Administration) specifications for repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 277,500 DIN 53457
Tensile strength at 68°F psi 6,962 DIN 53452
Compressive strength psi 8,702
Permissible static surface pressure (68°F) psi 4,496
Shore D-hardness 76 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 1012 DIN IEC 93
Surface resistance Ω < 1012 DIN 53482
10
Compressive Strength 9
With increasing temperatures, the compressive strength of iglide® A181 8
7
plain bearings decreases. The recommended maximum surface pressure is
6
a mechanical material parameter. No conclusions regarding the tribological
Deformation in %
5
properties can be drawn from this.
4
The graph at the right shows the elastic deformation of iglide® A181 3
during radial loading. At the recommended maximum surface pressure 2
of 4,496 psi the deformation is less than 3 %. 1
Plastic deformation is minimal up to this radial load. However, it is also 0
0 725 1,450 2,176 2,901 3,626 4,351 5,076
a result of the service time.
Pressure (psi)
140°F 73°F
➤ Compressive strength, Page 63
Deformation under load and temperature
14,500
Permissible Surface Speeds
iglide® A181 is developed for low surface speeds. Maximum speeds up
to 158 fpm (rotating) and 689 fpm (linear) respectively are permitted for
1,450
continuous use in dry operation.
These given values indicate the limits at which an increase up to the
continuous permissible temperature occurs. In practice these limit values
are not always reached due to interactions.
145
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Permissible pv values for iglide® A181 running dry against a steel Rotating 158 236
shaft, at 68°F Oscillating 118 197
Linear 689 984
Maximum surface speeds
Temperatures
The long-term upper temperature limit of +194°F permits the broad use 5,802
in applications with direct contact with food. As shown, in the graph 5,076
Pressure (psi)
2,176
➤ Application temperatures, Page 67 1,450
725
0
68 86 104 122 140 158 176 194
iglide A181
® Application Temperature
Temperature in °F
Minimum -58°F
Recommended maximum permissible static surface
Max. long-term +194°F
pressure of iglide® A181 as a result of the temperature
Max. short-term +230°F
Additional axial securing +140°F
0.4 0,26
0,23
0.3
Coefficient of friction (µ)
0,20
0,17
Coefficient of friction µ
0.2
0,14
0,11
0.1
0,08
0.0 0,05
19.69 29.53 39.37 49.21 59.06 68.90 78.74 88.58 98.43 0 725 1,450 2,176 2,901 3,626 4,351
Load (psi)
Surface Speed (fpm)
Coefficients of friction of iglide® A181 as a function of
Coefficients of friction of iglide® A181 as a function of the load, v = 1.97 fpm
the running speed; p = 108 psi
100
The graphs show the test results of iglide ® A181 bearings running
against various shaft materials. 80
Particular attention is paid in the food industry to the corrosion-
60
resistant shafts. The chart below shows that very low wear rates
Wear (µm/km)
can be achieved in combination with these shafts. As with many of 40
the iglide ® materials, wear rate increases with otherwise identical
20
parameters in rotation.
0
0 725 1,450 2,176 2,901 3,626 4,351
➤ Shaft Materials, Page 71
Pressure (psi)
Rotating Oscillating
5.0
3.0
4.0
2.5
3.0
Hard anodized aluminum
2.0
Automatic screw steel
2.0
Wear (µm/km)
HR Carbon Steel
1.5
1.0
304 Stainless
Wear (µm/km)
1.0
440B Steel
1050 Steel
0
0.5 145 290 435 580 725
Pressure (psi)
0.0
1050 Steel Hard anodized Aluminum
440B Hardened Steel 1050, Hard chromed
Wear of iglide® A181, rotating applications with different Wear with different shaft materials, oscillating and
shaft materials, p = 145 psi, v = 59 fpm rotating movement p = 290 psi
0.10
Medium Resistance
Hydrocarbon, chlorinated +
0.06
Greases, oils without additives +
Fuels + 0.04
Weak acids 0 to –
0.02
Strong acids –
Weak alkaline + 0.00
0.00 0.13 0.26 0.39 0.52 0.65 0.78 0.91 1.04 1.17 1.30
Strong alkaline + to 0
+ resistant, 0 conditionally resistant, – not resistant Moisture absorption (weight %)
Radiation Resistance
Plain bearings made of iglide® A181 are resistant to radiation up to an intensity of 2 · 102 Gy.
UV-Resistance
iglide® A181 bearings are only conditionally resistant to UV radiation.
Vacuum
When used in a vacuum environment, the iglide® A181 bearings release moisture as a vapor. Therefore, only dehumidified bearings are suitable
in a vacuum environment.
iglide® A181
Electrical Properties Specific volume resistance > 1012 Ωcm
iglide® A181 bearings are electrically insulating. Surface resistance > 1012 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A181SM-2023-30 20.0 23.0 30.0 20.040 20.124 23.000 23.021 19.948 20.000
A181SM-2225-15 22.0 25.0 15.0 25.000 25.021 21.948 22.000
A181SM-2225-20 22.0 25.0 20.0 25.000 25.021 21.948 22.000
22.040 22.124
A181SM-2225-25 22.0 25.0 25.0 25.000 25.021 21.948 22.000
A181SM-2225-30 22.0 25.0 30.0 25.000 25.021 21.948 22.000
A181SM-2427-15 24.0 27.0 15.0 27.000 27.021 23.948 24.000
A181SM-2427-20 24.0 27.0 20.0 27.000 27.021 23.948 24.000
24.040 24.124
A181SM-2427-25 24.0 27.0 25.0 27.000 27.021 23.948 24.000
A181SM-2427-30 24.0 27.0 30.0 27.000 27.021 23.948 24.000
A181SM-2428-30 24.0 28.0 30.0 24.040 24.124 28.000 28.021 23.948 24.000
A181SM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
A181SM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000
25.040 25.124
A181SM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
A181SM-2528-30 25.0 28.0 30.0 28.000 28.021 24.948 25.000
A181SM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
A181SM-2832-25 28.0 32.0 25.0 28.040 28.124 32.000 32.025 27.948 28.000
A181SM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
A181SM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
A181SM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
30.040 30.124
A181SM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000
A181SM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
A181SM-3236-20 32.0 36.0 20.0 36.000 36.025 31.938 32.000
A181SM-3236-30 32.0 36.0 30.0 32.050 32.150 36.000 36.025 31.938 32.000
A181SM-3236-40 32.0 36.0 40.0 36.000 36.025 31.938 32.000
A181SM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
A181SM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.050 35.150
A181SM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
A181SM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
A181SM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
A181SM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.050 40.150
A181SM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
A181SM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
A181SM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
A181SM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.050 50.150
A181SM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
A181SM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
A181SM-5055-20 50.0 55.0 20.0 50.050 50.150 55.000 55.030 49.938 50.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
A181 F M -01 03-02
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
A181FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
A181FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
A181FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
A181FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
A181FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 7.964 8.000
8.025 8.083
A181FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 7.964 8.000
A181FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
A181FM-1012-07 10.0 12.0 18.0 7.0 1.0 122.000 12.018 9.964 10.000
A181FM-1012-09 10.0 12.0 18.0 9.0 1.0 122.000 12.018 9.964 10.000
A181FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
A181FM-1012-12 10.0 12.0 18.0 12.0 1.0 122.000 12.018 9.964 10.000
A181FM-1012-17 10.0 12.0 18.0 17.0 1.0 122.000 12.018 9.964 10.000
A181FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
A181FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.032 12.102
A181FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
A181FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
A181FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.032 14.102
A181FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
A181FM-1517-09 15.0 17.0 23.0 9.0 1.0 16.000 16.018 13.957 14.000
A181FM-1517-12 15.0 17.0 23.0 12.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
A181FM-1517-17 15.0 17.0 23.0 17.0 1.0 16.000 16.018 13.957 14.000
A181FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.032 16.102
A181FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
A181FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
A181FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
A181FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
A181FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 19.948 20.000
A181FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
A181FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
A181FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
A181FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
A181FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
A181FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
30.040 30.124
A181FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
A181FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.050 35.150
A181FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
A181FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
A181FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
A181FM-4550-50 45.0 50.0 58.0 50.0 2.5 50.000 50.025 44.938 45.000
441
iglide®
A200
iglide® A200 - FDA compliant
FDA compliant, for low speeds
FDA compliant material for applications with low to
medium loads in immediate environs of (or contact) with
food or drugs.
iglide® A200 material with FDA (Food and Drug Administration) specifications for
repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 362,600 DIN 53457
Tensile strength at 68°F psi 16,820 DIN 53452
Compressive strength psi 7,832
Permissible static surface pressure (68°F) psi 2,611
Shore D-hardness 81 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 1013 DIN IEC 93
Surface resistance Ω < 1012 DIN 53482
Compressive Strength 10
8
The high abrasion resistance, the resistance to dirt, and the ability to run
dry make it possible to eliminate the customary, expensive protective 6
coverings of lubricated bearings.
Deformation (%)
The graph shows the elastic deformation of iglide® A200 for radial loads. 4
14,500
Permissible Surface Speeds
iglide® A200 was developed for low surface speeds. Running dry for
1,450 continuous usage, a maximum of 157 fpm (rotating) or 393 fpm (linear)
is possible.
These given values indicate the limits at which an increase up to the
145 continuous permissible temperature occurs. This increase is a result of
friction. In practice these limit values are not often reached, due to varying
application conditions.
14.5
Pressure (psi)
Temperatures
5,802
The maximum permissible short-term temperature is 338°F. With
increasing temperatures, the compressive strength of iglide® A200 plain
4,351
bearings decreases. The graph shows this relationship. The ambient
temperatures prevalent in the bearing system also have an effect on
the bearing wear. 2,901
Pressure (psi)
➤ Application temperatures, Page 67 1,450
0
68 86 104 122 140 158 176
iglide® A200 Application Temperature Temperature (°F)
Minimum -40°F
Max. long-term +176°F Recommended maximum permissible static surface
Max. short-term +338°F pressure of iglide® A200 as a result of the temperature
Additional axial securing +122°F
1.0 0.8
0.9
0.6
Coefficient of friction µ
0.8
Coefficient of friction µ
0.4
0.7
0.6 0.2
0.5
0
0.4 0 725 1,450 2,175 2,900
9.84 19.69 29.53 39.37 49.22 59.05 68.90 Pressure (psi)
Surface Speed (fpm)
Coefficients of friction of iglide® A200 as a function of Coefficients of friction of iglide® A200 as a function of
the running speed; p = 108 psi the load, v = 1.96 fpm
Shaft Materials 70
The graphs show the test results of iglide ® A200 bearings running 60
against various shaft materials. 50
The combination of iglide® A200 and hard chromed shaft clearly stands
40
out. Up to a range of about 362 psi, the wear of this combination
remains largely independent of the load. In pivoting applications below 30
Wear (µm/km)
a load p = 290 psi, the wear of iglide® A200 bearings is higher than in
20
rotating applications with equal load. Here the HR carbon steel shaft
is a positive exception with its much less coefficient of wear. 10
0
➤ Shaft Materials, Page 71 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
Oscillating Rotating
6 30
5 25
Hard anodized aluminum
20
4
Automatic screw steel
15
HR Carbon Steel
Wear (µm/km)
10
304 Stainless
Wear (µm/km)
2
1050 Steel
5
1
440B
0
0 145 290 435 580 725
0
Pressure (psi)
Fuels + 0.8
Radiation Resistance
Plain bearings made from iglide® A200 are resistant to radiation up to an intensity of 2 x 104 Gy. Higher radiation levels attack the material and can
cause essential mechanical properties to be lost.
UV-Resistance
iglide® A200 plain bearings are resistant to UV radiation.
Vacuum
In a vacuum environment, iglide® A200 plain bearings have restricted use.
iglide® A200
Electrical Properties Specific volume resistance > 1013 Ωcm
iglide A200 plain bearings are electrically insulating.
®
Surface resistance > 1012 Ω
447
iglide®
A350 iglide® A350 - Temperature and wear resistant
FDA compliant, for medium and high loads
Compliant with FDA and A very universal bearing for use in the area of food and
EC Directive 10/2011 EC pharmaceutical industries. Composition of FDA compli-
ant materials allows for use in areas where, due to the
contact with food, other bearings cannot be used. With
good tribological and mechanical properties, iglide® A350
For use with temperatures bearings are suitable for general purpose use in food
up to 356°F machinery.
iglide® A350 material complies with EC Directive 10/2011 EC and also with FDA
(Food and Drug Administration) specifications for repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 290,100 DIN 53457
Tensile strength at 68°F psi 15,950 DIN 53452
Compressive strength psi 11,310
Permissible static surface pressure (68°F) psi 8,702
Shore D-hardness 76 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1011 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Compressive Strength 6
The graph at the right shows the elastic deformation of iglide® A350 5
0
0 1450 2900 4,350 5,800 7,550 8,700
145
➤ Surface speed, Page 64
➤ pv value, Page 65
Pressure (psi)
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Temperatures
Its temperature resistance makes iglide® A350 an ideal material for a 11,600
bearing in the area of foodstuffs. Typically, temperatures range up to
+266 °F, which corresponds perfectly with the applicable temperature 8,702
range for iglide® A350. Short-term temperatures up to +410 °F are pos-
sible. Please note that at temperatures over +284°F, the pressfit forces
5,802
of the bearings may decrease and an additional axial securing device
Pressure (psi)
is recommended.
2,901
The wear-rate of iglide ® A350 bearings rises only a little with higher
temperatures. Tests have shown good wear results at +212 °F on all
tested shaft materials. 0
68 104 140 176 212 248 284 320 356
0.4
0.19
0.3 0.17
Coefficient of friction (µ)
0.15
0.2
0.13
0.11
0.1
0.09
0.0 0.07
20 29 40 49 59 69 79 89 98 0.05
0 725 1450 2176 2900 3626 4351
Surface speed (ft/min)
Pressure (psi)
Coefficients of friction of iglide® A350 as a function Coefficients of friction of iglide® A350 as a function
of the running speed; p = 145 psi of the load, v = 1.96 fpm
Shaft Materials
Corrosion-resistant steels are rather considered a natural choice for
use in the food industry.
Trials were therefore carried out especially on such materials. It has
been shown that there is no clear favorite 440B and hard chrome plated
steel are both suitable. Hard-anodized aluminum is also well suited for
both linear and rotating movements. For iglide® A350 a ground surface
with an averge roughness of 16-20 rms is recommended for the shaft.
25
20
4.5
4.0 15
3.5
Hard anodized aluminum
10
Wear (µm/km)
3.0
Automatic screw steel
2.5 5
HR Carbon Steel
2.0
304 Stainless
0
Wear (µm/km)
1.5
1050 Steel
0.5
Hard Chromed 440 B
0.0
304 Stainless
Wear, rotating application with different shaft Wear with different shaft materials in rotational operation,
materials, p = 145 psi, v = 59 fpm as a function of the pressure
Chemical Resistance
1.20
0.20
➤ Chemical table, Page 1364
0.10
0.00
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Moisture absorption (weight %)
Medium Resistance
Alcohol + Effect of moisture absorption on iglide ® A350 plain
Hydrocarbon + to 0 bearings
Radiation Resistance
Plain bearings made of iglide® A350 are resistant to radiation up to an intensity of 2 · 102 Gy.
UV-Resistance
iglide® A350 bearings are resistant to UV radiation.
Vacuum
When used in a vacuum environment, the iglide® A350 plain bearings release moisture as a vapor. Therefore, only dehumidified bear-
ings are suitable in a vacuum environment.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A350SM-2023-30 20.0 23.0 30.0 20.020 20.104 23.000 23.021 19.948 20.000
A350SM-2225-15 22.0 25.0 15.0 25.000 25.021 21.948 22.000
A350SM-2225-20 22.0 25.0 20.0 25.000 25.021 21.948 22.000
22.020 22.104
A350SM-2225-25 22.0 25.0 25.0 25.000 25.021 21.948 22.000
A350SM-2225-30 22.0 25.0 30.0 25.000 25.021 21.948 22.000
A350SM-2427-15 24.0 27.0 15.0 27.000 27.021 23.948 24.000
A350SM-2427-20 24.0 27.0 20.0 27.000 27.021 23.948 24.000
24.020 24.104
A350SM-2427-25 24.0 27.0 25.0 27.000 27.021 23.948 24.000
A350SM-2427-30 24.0 27.0 30.0 27.000 27.021 23.948 24.000
A350SM-2428-30 24.0 28.0 30.0 24.020 24.104 28.000 28.021 23.948 24.000
A350SM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
A350SM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000
25.020 25.104
A350SM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
A350SM-2528-30 25.0 28.0 30.0 28.000 28.021 24.948 25.000
A350SM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
A350SM-2832-25 28.0 32.0 25.0 28.020 28.104 32.000 32.025 27.948 28.000
A350SM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
A350SM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
A350SM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
30.020 30.104
A350SM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000
A350SM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
A350SM-3236-20 32.0 36.0 20.0 36.000 36.025 31.938 32.000
A350SM-3236-30 32.0 36.0 30.0 32.025 32.125 36.000 36.025 31.938 32.000
A350SM-3236-40 32.0 36.0 40.0 36.000 36.025 31.938 32.000
A350SM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
A350SM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.025 35.125
A350SM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
A350SM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
A350SM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
A350SM-4044-30 40.0 44.0 30.0 40.025 40.125 44.000 44.025 39.938 40.000
A350SM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
A350SM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
A350SM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.025 45.125
A350SM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
A350SM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
A350SM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
50.025 50.125
A350SM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
A350 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A350FM-0507-05 5.0 7.0 11.0 5.0 1.0 5.010 5.058 7.000 7.015 4.970 5.000
A350FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.015 5.970 6.000
A350FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.015 5.970 6.000
A350FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
A350FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 9.964 10.000
A350FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 9.964 10.000
8.013 8.071
A350FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 9.964 10.000
A350FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 9.964 10.000
A350FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
A350FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
A350FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
A350FM-1012-12 10.0 12.0 180 12.0 1.0 12.000 12.018 9.964 10.000
A350FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
A350FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
A350FM-1214-09 12.0 14.0 20.0 9.0 10 14.000 14.018 11.957 12.000
12.016 12.086
A350FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
A350FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
A350FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.016 14.086
A350FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
A350FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
A350FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
A350FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
A350FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
A350FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
A350FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
A350FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000
A350FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.021 17.957 18.000
A350FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 20.948 21.000
A350FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.020 20.104 23.000 23.021 20.948 21.000
A350FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 20.948 21.000
A350FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
A350FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.020 25.104 28.000 28.021 24.948 25.000
A350FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
A350FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.025 29.948 30.000
30.020 30.104
A350FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.025 29.948 30.000
A350FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.025 35.125
A350FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 451
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A350FM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.025 40.125
A350FM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
A350FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.025 45.125 50.000 50.025 44.938 45.000
459
iglide®
A500
iglide® A500 - FDA and EC Directive compliant
FDA compliant
Compliant with EC
Directive 10/2011 EC Plastic bearings made of iglide® A500 can be exposed
FDA compliant to extremely high temperatures and consist of materials
suitable for direct contact with food (FDA conformity)
Temperature resistant
from -148°F to 482°F
iglide® A500 material complies with EC Directive 10/2011 EC and also with FDA
(Food and Drug Administration) specifications for repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 522,100 DIN 53457
Tensile strength at 68°F psi 20,310 DIN 53452
Compressive strength psi 17,110
Permissible static surface pressure (68°F) psi 17,400
Shore D-hardness 83 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1014 DIN IEC 93
Surface resistance Ω > 1013 DIN 53482
Compressive Strength 10
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Surface Speed (fpm) Continuous Short Term
fpm fpm
Permissible pv values for iglide® A500 running dry against a steel
shaft, at 68°F Rotating 118 196
Oscillating 78 137
Linear 196 393
Temperatures
23,200
The short term permissible highest application temperature is 572°F.
20,300
The compressive strength of iglide ® A500 plain bearings decreases
17,400
with increasing temperatures. The graph illustrates this relationship.
14,500
Pressure (psi)
8,702
5,802
2,901
0
68 122 176 248 302 392 482
iglide® A500 Application Temperature Temperature (°F)
Minimum -148°F
Recommended maximum permissible static surface
Max. long-term +482°F
pressure of iglide® A500 as a result of the temperature
Max. short-term +572°F
Additional axial securing +266°F
0.5 0.7
0.6
0.4
0.5
Coefficient of friction (µ)
0.4
0.3
0.3
0.2 0.2
0.1
0.1 0.0
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 1450 2901 4351 5802 7252 8702 10150
Pressure (psi)
Surface Speed (fpm)
Coefficients of friction of iglide® A500 as a function of Coefficients of friction of iglide® A500 as a function of
the running speed; p = 108 psi the load, v = 1.96 fpm
Wear (µm/km)
60
With regard to oscillating movements against shafts of 1050 steel,
40
the wear resistance is better than that of rotation under the same 20
pressure. If the shaft material you intend to use is not included in these 0
graphs please contact us. 0 1450 2901 4351 5802 7252
Pressure (psi)
rotating oscillating
➤ Shaft Materials, Page 71
Wear with different shaft materials, oscillating and
rotating movement p = 290 psi
30
27
24
Hard anodized aluminum
21
Automatic screw steel
18
HR Carbon Steel
15
304 Stainless
12
Wear (µm/km)
9
6
440B
1050
3
0
0.16
Medium Resistance
0.14
Radiation Resistance
Plain bearings made from iglide® A500 rank among the most radiation resistant products in the iglide® range. The bearings are resistant up to a
radiation intensity of 2 x 10 Gy. Higher radiation affects the material and can result in the loss of basic mechanical characteristics.
UV-Resistance
To a large extent, iglide® A500 plain bearings are resistant to UV radiation.
Vacuum
In a vacuum environment, iglide® A500 plain bearings can only be used to a limited degree.
iglide® A500
Electrical Properties Specific volume resistance > 1014 Ωcm
iglide A500 plain bearings are electrically insulating.
®
Surface resistance > 1013 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A500SM-2023-30 20.0 23.0 30.0 20.020 20.104 23.000 23.021 19.948 20.000
A500SM-2225-15 22.0 25.0 15.0 25.000 25.021 21.948 22.000
A500SM-2225-20 22.0 25.0 20.0 25.000 25.021 21.948 22.000
22.020 22.104
A500SM-2225-25 22.0 25.0 25.0 25.000 25.021 21.948 22.000
A500SM-2225-30 22.0 25.0 30.0 25.000 25.021 21.948 22.000
A500SM-2427-15 24.0 27.0 15.0 27.000 27.021 23.948 24.000
A500SM-2427-20 24.0 27.0 20.0 27.000 27.021 23.948 24.000
24.020 24.104
A500SM-2427-25 24.0 27.0 25.0 27.000 27.021 23.948 24.000
A500SM-2427-30 24.0 27.0 30.0 27.000 27.021 23.948 24.000
A500SM-2528-15 25.0 28.0 15.0 28.000 28.021 24.948 25.000
A500SM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000
25.020 25.104
A500SM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
A500SM-2528-30 25.0 28.0 30.0 28.000 28.021 24.948 25.000
A500SM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
A500SM-2832-25 28.0 32.0 25.0 28.020 28.104 32.000 32.025 27.948 28.000
A500SM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
A500SM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
A500SM-3034-25 30.0 34.0 25.0 34.000 34.025 29.948 30.000
30.020 30.104
A500SM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000
A500SM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
A500SM-3236-20 32.0 36.0 20.0 36.000 36.025 31.938 32.000
A500SM-3236-30 32.0 36.0 30.0 32.025 32.125 36.000 36.025 31.938 32.000
A500SM-3236-40 32.0 36.0 40.0 36.000 36.025 31.938 32.000
A500SM-3539-20 35.0 39.0 20.0 39.000 39.025 34.938 35.000
A500SM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.025 35.125
A500SM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
A500SM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
A500SM-4044-20 40.0 44.0 20.0 44.000 44.025 39.938 40.000
A500SM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.025 40.125
A500SM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
A500SM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
A500SM-4550-20 45.0 50.0 20.0 50.000 50.025 44.938 45.000
A500SM-4550-30 45.0 50.0 30.0 50.000 50.025 44.938 45.000
45.025 45.125
A500SM-4550-40 45.0 50.0 40.0 50.000 50.025 44.938 45.000
A500SM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
A500SM-5055-20 50.0 55.0 20.0 55.000 55.030 49.938 50.000
50.025 50.125
A500SM-5055-30 50.0 55.0 30.0 55.000 55.030 49.938 50.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
30°
A500 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
A500FM-0608-04 6.0 8.0 12.0 4.0 1.0 8.000 8.012 5.970 6.000
A500FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.010 6.058 8.000 8.012 5.970 6.000
A500FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.012 5.970 6.000
A500FM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 9.964 10.000
A500FM-0810-07 8.0 10.0 15.0 7.5 1.0 10.000 10.015 9.964 10.000
8.013 8.071
A500FM-0810-09 8.0 10.0 15.0 9.5 1.0 10.000 10.015 9.964 10.000
A500FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 9.964 10.000
A500FM-1012-07 10.0 12.0 18.0 7.0 1.0 12.000 12.018 9.964 10.000
A500FM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000
A500FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
A500FM-1012-12 10.0 12.0 18.0 12.0 1.0 12.000 12.018 9.964 10.000
A500FM-1012-17 10.0 12.0 18.0 17.0 1.0 12.000 12.018 9.964 10.000
A500FM-1214-07 12.0 14.0 20.0 7.0 1.0 14.000 14.018 11.957 12.000
A500FM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.016 12.086
A500FM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
A500FM-1214-17 12.0 14.0 20.0 17.0 1.0 14.000 14.018 11.957 12.000
A500FM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.016 14.086
A500FM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
A500FM-1517-09 15.0 17.0 23.0 9.0 1.0 17.000 17.018 14.957 15.000
A500FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
A500FM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
A500FM-1618-12 16.0 18.0 24.0 12.0 1.0 18.000 18.018 15.957 16.000
16.016 16.086
A500FM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000
A500FM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.018 17.957 18.000
A500FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.018 17.957 18.000
A500FM-1820-22 18.0 20.0 26.0 22.0 1.0 20.000 20.018 17.957 18.000
A500FM-2023-11 20.0 23.0 30.0 11.5 1.5 23.000 23.021 20.948 21.000
A500FM-2023-16 20.0 23.0 30.0 16.5 1.5 20.020 20.104 23.000 23.021 20.948 21.000
A500FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 20.948 21.000
A500FM-2528-11 25.0 28.0 35.0 11.5 1.5 28.000 28.021 24.948 25.000
A500FM-2528-16 25.0 28.0 35.0 16.5 1.5 25.020 25.104 28.000 28.021 24.948 25.000
A500FM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
A500FM-3034-16 30.0 34.0 42.0 16.0 2.0 34.000 34.021 29.948 30.000
30.020 30.104
A500FM-3034-26 30.0 34.0 42.0 26.0 2.0 34.000 34.021 29.948 30.000
A500FM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
35.025 35.125
A500FM-3539-26 35.0 39.0 47.0 26.0 2.0 39.000 39.025 34.938 35.000
A500FM-4044-30 40.0 44.0 52.0 30.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 463
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
A500FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
A500FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.025 45.125 50.000 50.025 44.938 45.000
471
iglide®
A160
iglide® A160 - FDA and EC Directive compliant
FDA compliant
Compliant with EC iglide ® A160 offers maximum media resistance in the
Directive 10/2011 EC medium temperature range and is a true low-cost iglide®
FDA compliant material. The properties of iglide® A160 makes it suitable
for applications in the food industry.
Self-lubricating and
maintenance-free
iglide® A160 material complies with EC Directive 10/2011 EC and also with FDA
(Food and Drug Administration) specifications for repeated contact with food.
Mechanical Properties
Modulus of elasticity psi 166,900 DIN 53457
Tensile strength at 68°F psi 2,756 DIN 53452
Compressive strength psi 5,366
Permissible static surface pressure (68°F) psi 2,176
Shore D-hardness 60 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 12
With increasing temperatures, the compressive strength of iglide ®
10
A160 plain bearings decreases. The recommended maximum surface
pressure is a mechanical material parameter. No conclusions regarding 8
4
➤ Compressive strength, Page 63
2
0
0 435 870 1,305 1,740 2,176
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
iglide® A160 was developed for low surface speeds. Maximum speeds
up to 98 fpm (rotating) and 393 fpm (linear) respectively are permitted for
1,450 continuous application in dry operation.
The given values indicate the limits at which an increase up to the
continuous permissible temperature occurs. This increase is a result of
friction. In practice, this temperature level is rarely reached, due to varying
145 application conditions.
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Surface Speed (fpm) Continuous Short Term
fpm fpm
Permissible pv values for iglide® A160 running dry against a steel
shaft, at 68°F Rotating 98 137
Oscillating 78 118
Linear 393 590
Temperatures
2,901
With increasing temperatures, the compressive strength of iglide® A160
plain bearings decreases. The diagram shows this inverse relationship.
2,176
The temperatures prevailing in the bearing system also have an influence
on the bearing wear. At temperatures over +140 °F an additional securing
is required. 1,450
Pressure (psi)
➤ Application temperatures, Page 67 725
iglide A160
® Application Temperature 68 86 104 122 140 158 176 194
0.6 0.3
0.5
Coefficient of friction (µ)
0.4 0.2
0.3
0.2 0.1
0.1
0.0
0.0
19.69 39.37 59.06 78.74 98.43 0 363 725 1,088 1,450 1,813 2,176
Coefficients of friction of iglide® A160 as a function of Coefficients of friction of iglide® A160 as a function of
the running speed; p = 145 psi the load, v = 1.96 fpm
2.0
Shaft Materials
The graphs illustrate the results of testing different shaft materials
1.5
HR Carbon Steel
as hard-chrome-plated steel prove to be the best counter-materials.
304 Stainless
However, on 440 stainless steel shafts, the wear rate increases quickly as
Wear (µm/km)
1050 Steel
loads increase. With case hardened steel shafts, wear rates in oscillating 0.5
440B
applications is exemplary when compared to rotating applications. As
shown in the graph below, in rotating applications, wear rates of a range
0.0
of iglide® materials are higher than those found in oscillating applications.
4.5
160 4.0
3.5
120 3.0
2.5
2.0
80
Wear (µm/km)
1.5
Wear (µm/km)
1.0
40
0.5
0.0
0 0 72 145 217 290
725 1,450 2,176 2,901 Pressure (psi)
Pressure (psi)
1050 Steel Hard anodized aluminum
Rotating Oscillating
304 Stainless High grade steel
Wear with different shaft materials, oscillating and Wear with different shaft materials in rotational
rotating movement p = 290 psi operation, as a function of the pressure
Medium Resistance
Alcohol +
Hydrocarbon, chlorinated +
Greases, oils without additives +
Fuels + to 0
Weak acids +
Strong acids +
Weak alkaline +
Strong alkaline +
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Plain bearings made from iglide® A160 are resistant to radiation up to an intensity of 1 x 105 Gy. Higher radiation levels affect the material and can
result in the loss of essential mechanical properties.
UV-Resistance
iglide® A160 plain bearings are partially resistant to the impact of UV radiation.
Vacuum
In a vacuum environment, iglide® A160 plain bearings release moisture as a vapor. Therefore only dehumidified bearings are suitable in a vacuum
environment.
iglide® A160
Electrical Properties Specific volume resistance > 1012 Ωcm
iglide A160 plain bearings are electrically insulating.
®
Surface resistance > 1012 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
A160SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
A160SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
A160SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
A160SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
A160SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
A160SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
A160 F M -06 08-06
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
A160FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.012 5.970 6.000
A160FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
A160FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
A160FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
A160FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
A160FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
479
iglide®
A290
iglide® A290 - Robust
Good abrasion resistance
iglide® A290 bearings comply with the requirements of
Complies with the the BfR for contact with food. For medium and high loads.
requirements of the BfR
Suited for direct contact with food l When your bearing comes in direct contact with
food
l For low speeds
l When quiet operation is important
l When good abrasion resistance is needed
Good abrasion resistance l When very good mechanical properties are required
l When a physiologically safe bearing is needed
iglide® A290 material complies with the requirements of the BfR for contact with food.
Mechanical Properties
Modulus of elasticity psi 1,276,000 DIN 53457
Tensile strength at 68°F psi 32,260 DIN 53452
Compressive strength psi 13,200
Permissible static surface pressure (68°F) psi 10,150
Shore D-hardness 88 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 1011 DIN IEC 93
Surface resistance Ω < 1011 DIN 53482
Compressive Strength 10
8
iglide® A290 plain bearings have a recommended maximum surface
pressure of 10,150 psi. At this load, the deformation at room tempera- 6
ture is only 2.5%. Plastic deformation is close to zero up to this load.
However, it is also affected by the cycle time. 4
Deformation (%)
2
➤ Compressive strength, Page 63
0
0 1450 2901 4351 5802 7252 8702 10150
Pressure (psi)
140°F 73°F
Deformation under load and temperature
14,500
Permissible Surface Speeds
iglide® A290 is suitable for low surface speeds. Because of the relatively
high friction rate in the low load range, plain bearings made of iglide®
1,450
A290 heat up more than other bearings. At high speed, the friction
additionally increases.
14.5
.197 1.97 19.7 197 1,969 Continuous Short Term
Surface Speed (fpm) fpm fpm
Permissible pv values for iglide® A290 running dry against a steel Rotating 196 393
shaft, at 68°F
Oscillating 137 275
Linear 590 787
Temperatures
17,400
The maximum permissible short-term temperature is 356°F.
With an increase in temperature, the compressive strength of iglide ® 14,500
A290 plain bearings decreases. The graph shows this relationship. 11,600
The ambient temperatures prevalent in the bearing system also have an
8,702
effect on wear. With rising temperatures, an increase in wear results.
From temperatures of 248°F. this effect becomes significant.
Pressure (psi)
5,802
2,901
➤ Application temperatures, Page 67
0
68 122 176 248 302
iglide® A290 Application Temperature Temperature (°F)
Minimum -40°F
Max. long-term +284°F Recommended maximum permissible static surface
Max. short-term +356°F pressure of iglide® A290 as a result of the temperature
Additional axial securing +230°F
0.6 0.50
0.45
0.40
0.5
Coefficient of friction (µ)
0.35
0.30
0.4 0.25
0.20
0.15
0.3
0.10
9.84 19.69 29.53 39.37 49.21 59.06 68.90 78.74 0 1450 2901 4351 5802 7252 8702 10150
Coefficients of friction of iglide® A290 as a function of Coefficients of friction of iglide® A290 as a function of
the running speed; p = 108 psi the load, v = 1.96 fpm
Shaft Materials 60
The graphs show the results of testing different shaft materials with
50
iglide ® A290 plain bearings. The improved tribological properties
compared to iglide® A200 are also reflected in the wear values. For 40
low loads, the differences in wear resistance for iglide ® A290 with
different shaft materials is very pronounced. The graph shows that with 30
Wear (µm/km)
20
Hard chromed shafts are also well suited for oscillating applications,
frequently found in packaging machines. Other hardened surfaces 10
are also recommended for oscillating movements, for example 1050
0
hardened and ground steel. 1050 Hard 304 Stainless HR carbon
steel chromed steel steel
➤ Shaft Materials, Page 71 Oscillating Rotating
30 16
27 14
24 12
Hard anodized aluminum
21 10
Automatic screw steel
18 8
HR Carbon Steel
15 6
Wear (µm/km)
304 Stainless
12 4
Wear (µm/km)
9 2
6
440B
0
1050
3 0.0 72 145 217 290 362 435 507 580 652 725
0
Pressure (psi)
1.2
Medium Resistance
Alcohol + to 0 1.0
Radiation Resistance
Plain bearings made from iglide® A290 are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® A290 is partially resistant to UV radiation, certain tribological properties can be affected.
Vacuum
In a vacuum environment, iglide® A290 plain bearings have limited use due to the high moisture absorption.
iglide® A290
Electrical Properties Specific volume resistance > 1011 Ωcm
iglide A290 plain bearings are electrically insulating.
®
Surface resistance > 1011 Ω
485
iglide®
UW160
iglide® UW160 - For contact with drinking water
KTW compliant
iglide® UW160 is optimized for continuous operation while
Extremely wear-resistant in liquid for submerged in liquid media.
long-term operation
Self-lubricating and
maintenance-free
Mechanical Properties
Modulus of elasticity psi 195,700 DIN 53457
Tensile strength at 68°F psi 3,191 DIN 53452
Compressive strength psi 4,461
Permissible static surface pressure (68°F) psi 2,176
Shore D-hardness 60 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 10
With increasing temperatures, the compressive strength of iglide® UW160
plain bearings decreases. The recommended maximum surface pressure is 8
0
0 725 1,450 2,176
Temperatures
2,901
iglide® UW160 was developed for use in liquid media in normal and medium
temperature range.
2,176
As with all thermoplastics, the compression resistance of iglide® UW160
decreases with increasing temperature. The occurring temperatures in the
bearing system also have an effect on the bearing wear. The wear rate rises 1,450
Pressure (psi)
with increasing temperatures. At temperatures over +158 °F an additional
securing is required. 725
0.6 0.3
0.5
0.4 0.2
Coefficient of friction µ
Coefficient of friction (µ)
0.3
0.2 0.1
0.1
0.0 0.0
19.69 39.37 59.06 78.74 98.43 0 362 725 1,088 1,450 1,813 2,176
Coefficients of friction of iglide UW160 as a function ® Coefficients of friction of iglide® UW160 as a function
of the running speed; p = 145 psi of the load, v = 1.96 fpm
The graphs show the test results of iglide® UW160 bearings running
against various shaft materials. In the example of a rotational movement 120
with radial loads of 145 psi and a speed of 59 fpm, it becomes clear
that iglide® UW160 achieves good wear values with a variety shafts 80
Wear (µm/km)
except for 304 stainless steel. Is is also clear that there are better
iglide® materials for dry running. As with many other iglide® materials
40
in dry running the graph shows the significantly higher wear in rotation
than in pivoting with otherwise identical parameters.
0
725 1,160 1,595 2,176
➤ Shaft Materials, Page 71
Pressure (psi)
Rotating Oscillating
15
12
Hard anodized aluminum
9
1050, hard chromed
HR carbon steel
6
304 Stainless
Wear (µm/km)
1050 Steel
3
440B
Medium Resistance
Alcohol +
Hydrocarbon, chlorinated +
Greases, oils without additives +
Fuels +
Weak acids + to 0
Strong acids +
Weak alkaline +
Strong alkaline +
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Plain bearings made of iglide® UW160 are resistant to radiation up to an intensity of 3 · 102 Gy.
UV-Resistance
iglide® UW160 bearings are only conditionally resistant to UV rays.
Vacuum
In a vacuum environment, existing moisture will outgas. For this reason only, the dry iglide® UW160 bearings are suitable for vacuum.
iglide® UW160
Electrical Properties Specific volume resistance > 1012 Ωcm
iglide UW160 plain bearings are electrically insulating.
®
Surface resistance > 1012 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
30°
d1
For tolerance values
Metric
Dimensions according to ISO 3547-1 and special dimensions please refer to page 489
*Based on steel housing bore
UW160SM-0304-03 3.0 4.5 3.0 3.014 3.054 4.500 4.512 2.975 3.000
UW160SM-0405-04 4.0 5.5 4.0 4.020 4.068 5.500 5.512 3.970 4.000
UW160SM-0507-05 5.0 7.0 5.0 5.020 5.068 7.000 7.015 4.970 5.000
UW160SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
UW160SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
UW160SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
Outer-Ø d2 (mm)
f
Inner-Ø d1 (mm)
Length b1 (mm)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
Metric
please refer to page 489
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
UW160FM-0304-05 3.0 4.5 7.5 5.0 0.75 3.014 3.054 4.500 4.512 2.975 3.000
UW160FM-0405-06 4.0 5.5 9.5 6.0 0.75 4.020 4.068 5.500 5.512 3.970 4.000
UW160FM-0507-07 5.0 7.0 11.0 7.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
UW160FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
UW160FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
UW160FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
493
iglide®
T220
iglide® T220 - For the tobacco industry
FDA compliant
iglide® T220 material meets the requirements for use in
the tobacco processing industry. The material is free from
Free of unwanted carcinogenic additives such as PTFE.
components as requested
by manufacturers
of tobacco products
iglide® T220 material with FDA (Food and Drug Administration) specifications for
repeated contact with food.
Contact igus®
$ Order dependent mm
Sizes available upon request
Mechanical Properties
Modulus of elasticity psi 261,100 DIN 53457
Tensile strength at 68°F psi 9,427 DIN 53452
Compressive strength psi 7,977
Permissible static surface pressure (68°F) psi 5,802
Shore D-hardness 76 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1010 DIN IEC 93
Surface resistance Ω > 1010 DIN 53482
10.0
iglide ® T220 plain bearings can be stressed to the permissible
limit of 6,527 psi. The load, however, has an impact on the wear
of the bearings. The permissible load is further limited by increasing
Deformation (%)
temperatures. 5.0
2.1
➤ Compressive strength, Page 63
0.0
0 2.176 4.351 6.527
Pressure (psi)
140°F 73°F
14,500
Permissible Surface Speeds
The maximum speed of iglide® T220 plain bearings in continuous rota-
tion is 78 fpm. The frictional heat generated define the permissible
1,450
speeds. Because of this intermittent service and linear movements,
higher speeds can be attained.
14.5
.197 1.97 19.7 197 1,969
Temperatures 17,400
Pressure (psi)
being used at temperatures over 140°F. Please contact us if you have 5,802
iglide T220
® Application Temperature Temperature (°F)
Minimum -40°F
Recommended maximum permissible static surface
Max. long-term +212°F pressure of iglide® T220 as a result of the temperature
Max. short-term +320°F
Additional axial securing +122°F
0,5 0.7
0.6
0,4
0.5
Coefficient of friction (µ)
0.4
0,3
0.3
0.2
0,2
0.1
0,1 0.0
9.84 19.69 29.53 39.37 49.21 59.06 0 1450 2901 4351 5802 7252 8702 10150 11600
Surface Speed (fpm) Pressure (psi)
Coefficients of friction of iglide® T220 as a function of Coefficients of friction of iglide® T220 as a function of
the running speed; p = 108 psi the load, v = 1.96 fpm
The graphs show the wear resistance results of testing different shaft
80
materials with iglide ® T220 plain bearings. If recommendations are
observed, the service life of a bearing application can be considerably 60
improved. The graph shows that the bearings react with a heavy
increase in wear when load is increased. Therefore it should be noted 40
Wear (µm/km)
that the load should be kept below 725 psi. (Determined by the
dimensions of the bearing.) 20
0
➤ Shaft Materials, Page 71 870
0 145 290 435 580 725
Pressure (psi)
rotating oscillating
7.0 24
6.5
6.0 20
5.5
Hard anodized aluminum
5.0 16
Automatic screw steel
4.5
1050,hard chromed
4.0 12
HR Carbon Steel
3.5
Wear (µm/km)
8
3.0
304 Stainless
Wear (µm/km)
2.5 4
2.0
1.5
440B
1050
0
1.0 14 36 108 145 290
0.0 Pressure (psi)
0.16
Medium Resistance
0.14
Alcohol +
0.12
Hydrocarbon, chlorinated –
Radiation Resistance
Plain bearings made from iglide® T220 are radiation resistant up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® T220 are not resistant to the impact of UV radiation.
Vacuum
Applications in a vacuum are only possible to a limited extent. Only dehumidified iglide® T220 bearings should be tested in a vacuum.
iglide® T220
Electrical Properties Specific volume resistance > 1010 Ωcm
iglide T220 plain bearings are electrically insulating.
®
Surface resistance > 1010 Ω
max. +275 °F
min. –76 °F
3 materials
Ø 1/8 to 3 inches
more dimensions on request
Ø 5 to 90 mm
mm
more dimensions on request
iglide® Z thrust washers eliminate the possibility of extreme wear due Conventional roller ball bearings were replaced with iglide® plain
to dust and humidity in the contact zone of this plating machine’s bearings, which are corrosion and dirt resistant.
wheels.
iglide® Q bearings are able to cope with high loads and pivoting Rugged plastic plain bearings are used in the pivot points of this
angles, such as those found in this electric scooter. agricultural system.
iglide® plain bearings used in this wheel mount and jointed arm are The plastic plain bearings used in this excavator are able to stand
resistant to dirt and humidity, unlike metal bearings. up to the moisture and dirt as the spades are pushed into the soil.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglide® Q l l l l l
iglide® Q2 l l l l
iglide® TX1 l l l l l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194°F +302°F
iglide® Q l
iglide® Q2 l l l
iglide® TX1 l l l l
iglide® Q 505
iglide® Q2 517
iglide® Q 6 3 505
iglide® Q2 4 4 517
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
iglide® Q
• Excellent wear resistance, especially for
extreme loads
• Recommended for extreme pv values
• Good coefficient of friction
• Resistant to dirt
505
iglide®
Q
iglide® Q - For high loads
Wear-resistant on most shafts
iglide® Q is the low priced solution for high duty cycles at
Excellent wear resistance, high to extreme loads. Bearings made from this material
especially for extreme loads can be used in all types of motion, but is best suited for
oscillating applications.
Recommended for
extreme pv values
Mechanical Properties
Modulus of elasticity psi 652,700 DIN 53457
Tensile strength at 68°F psi 17,400 DIN 53452
Compressive strength psi 12,910
Permissible static surface pressure (68°F) psi 14,500
Shore D-hardness 83 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1015 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 7
6
iglide ® Q is a material that is used when high loads over 7,250 psi are 5
required. The graph shows the elastic deformation of iglide® Q for radial
4
loads. At the maximum permissible static load of 14,500 psi, deformation
3
Deformation (%)
0
0 3,626 7,252 10,880 14,500
Pressure (psi)
140°F 73°F
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Continuous Short Term
Surface Speed (fpm)
fpm fpm
Permissible pv value for iglide® Q running dry against a steel
shaft, at 68°F Rotating 196 393
Oscillating 137 275
Linear 984 1181
Temperatures
14500
Plain bearings made of iglide® Q have excellent wear resistance even at 13050
high temperatures. The maximum long-term application temperature is 11600
275°F. For the short-term, the material can withstand 311°F. Because of 10150
different environmental influences, the bearing can lose pressfit at lower 8700
temperatures. Therefore, it may be necessary to secure the bearings in 7250
the housing bore. Also, notice that the coefficient of friction increases 5800
Pressure (psi)
rapidly as temperature increases beginning at approximately 212°F. 4350
2900
➤ Application temperatures, Page 67 1450
0
0 68 104 140 176 212 248 284 320
iglide® Q Application Temperature
Temperature (°F)
Minimum -40°F
Max. long-term +275°F Recommended maximum static surface pressure of
iglide® Q as a result of the temperature
Max. short-term +311°F
Additional axial securing +122°F
Temperature iglide® Q
0.4
0.4
0.3 0.3
Coefficient of friction µ
Coefficient of friction µ
0.2 0.2
0.1 0.1
0.0 0.0
9.84 19.69 29.53 39.37 49.22 59.05 68.90 73 145 218 290 363 435 508 580 653 725
Surface Speed (fpm) Pressure (psi)
Coefficient of friction as a result of the surface speed; Coefficient of friction as a result of the load, v = 1.97 fpm
load = 108 psi constant
Shaft Materials 10
The graphs show results of testing different shaft materials with plain
8
bearings made of iglide® Q.
iglide® Q plain bearings have a higher average wear rate at low loads,
6
than bearings made of iglide ® J or L280. However, the strength
of iglide ® Q is its wear resistance at heavy loads and in oscillating
4
operation. In oscillating movements, iglide® Q plain bearings perform
Wear (µm/km)
best against hard chromed or machined steel shafts. 2
If the shaft material you plan to use is not contained in this list, please
contact us. 0
1050 Hard 304 Stainless HR carbon
➤ Shaft Materials, Page 71 steel chromed steel steel
Oscillating Rotating
180
4.5 160
4.0 140
120
3.5
Hard anodized aluminum
100
Automatic screw steel
3.0
1050, hard chromed
80
2.5
Wear (µm/km) 60
HR carbon steel
2.0 40
304 Stainless
Wear (µm/km)
1050 Steel
1.5 20
1.0 0
440B
Radiation Resistance
Plain bearings made from iglide® Q are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
The tribological properties of iglide® Q plain bearings stay constant for the most part under weathering effects.
Vacuum
When used in a vacuum, the iglide® Q plain bearings release existing moisture as a vapor. Therefore, only dehumidified bearings made of iglide®
Q are suitable for the vacuum.
iglide® Q
Electrical Properties Specific volume resistance > 1015 Ωcm
iglide Q plain bearings are electrically insulating.
®
Surface resistance > 1012 Ω
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
30°
d1
For tolerance values
Inch
please refer to page 509
*Based on steel housing bore
QSI-0203-04 1/8 3/16 1/4 .1251 .1269 .1873 .1878 .1236 .1243
QSI-0304-04 3/16 1/4 1/4 .2497 .2503 .1858 .1865
.1873 .1892
QSI-0304-06 3/16 1/4 3/8 .2497 .2503 .1858 .1865
QSI-0405-04 1/4 5/16 1/4 .3122 .3128 .2481 .2490
QSI-0405-06 1/4 5/16 3/8 .2498 .2521 .3122 .3128 .2481 .2490
QSI-0405-08 1/4 5/16 1/2 .3122 .3128 .2481 .2490
QSI-0506-04 5/16 3/8 1/4 .3747 .3753 .3106 .3115
QSI-0506-06 5/16 3/8 3/8 .3125 .3148 .3747 .3753 .3106 .3115
QSI-0506-08 5/16 3/8 1/2 .3747 .3753 .3106 .3115
QSI-0607-04 3/8 15/32 1/4 .4684 .4691 .3731 .3740
QSI-0607-06 3/8 15/32 3/8 .3750 .3773 .4684 .4691 .3731 .3740
QSI-0607-08 3/8 15/32 1/2 .4684 .4691 .3731 .3740
QSI-0708-08 7/16 17/32 1/2 .4379 .4406 .5309 .5316 .4355 .4365
QSI-0809-12 1/2 19/32 3/4 .5003 .5030 .5934 .5941 .4980 .4990
QSI-1011-12 5/8 23/32 3/4 .6253 .6280 .7184 .7192 .6230 .6240
QSI-1214-08 3/4 7/8 1/2 .8747 .8755 .7479 .7491
QSI-1214-12 3/4 7/8 3/4 .7507 .7541 .8747 .8755 .7479 .7491
QSI-1214-16 3/4 7/8 1 .8747 .8755 .7479 .7491
QSI-1416-16 7/8 1 1 .8757 .8791 .9997 1.0005 .8729 .8741
QSI-1618-16 1 1 1/8 1 1.1247 1.1255 .9979 .9991
1.0007 1.0041
QSI-1618-24 1 1 1/8 1 1/2 1.1247 1.1255 .9979 .9991
QSI-1820-24 1 1/8 1 9/32 1 1/2 1.1254 1.1288 1.2808 1.2818 1.1226 1.1238
QSI-2022-20 1 1/4 1 13/32 1 1/4 1.4058 1.4068 1.2472 1.2488
1.2508 1.2548
QSI-2022-24 1 1/4 1 13/32 1 1/2 1.4058 1.4068 1.2472 1.2488
QSI-2426-24 1 1/2 1 21/32 1 1/2 1.5008 1.5408 1.6558 1.6568 1.4972 1.4988
QSI-2629-20 1 5/8 1 25/32 1 1/4 1.6258 1.6297 1.7808 1.7818 1.6222 1.6238
QSI-2831-32 1 3/4 1 15/16 2 1.7508 1.7547 1.9371 1.9381 1.7471 1.7487
QSI-3235-12 2 2 3/16 3/4 2.1871 2.1883 1.9969 1.9981
QSI-3235-16 2 2 3/16 1 2.1871 2.1883 1.9969 1.9981
QSI-3235-24 2 2 3/16 1 1/2 2.0011 2.0057 2.1871 2.1883 1.9969 1.9981
QSI-3235-32 2 2 3/16 2 2.1871 2.1883 1.9969 1.9981
QSI-3235-40 2 2 3/16 2 1/2 2.1871 2.1883 1.9969 1.9981
QSI-3639-32 2 1/4 2 7/16 2 2.2531 2.2577 2.4365 2.4377 2.2489 2.2507
QSI-4043-16 2 1/2 2 11/16 1.0 2.6869 2.6881 2.4993 2.5011
2.5035 2.5082
QSI-4043-32 2 1/2 2 11/16 2.0 2.6869 2.6881 2.4993 2.5011
QSI-4851-16 3.0 3 3/16 1.0 3.1858 3.1872 2.9982 3.0000
QSI-4851-32 3.0 3 3/16 2.0 3.0023 3.0070 3.1858 3.1872 2.9982 3.0000
QSI-4851-48 3.0 3 3/16 3.0 3.1858 3.1872 2.9982 3.0000
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
please refer to page 509
Inch
*Based on steel housing bore
QFI-0203-04 1/8 3/16 .312 1/4 .032 .1251 .1269 .1873 .1878 .1236 .1243
QFI-0304-06 3/16 1/4 .375 3/8 .032 .1873 .1892 .2497 .2503 .1858 .1865
QFI-0405-06 1/4 5/16 .500 3/8 .032 .3122 .3128 .2481 .2490
.2498 .2521
QFI-0405-08 1/4 5/16 .500 1/2 .032 .3122 .3128 .2481 .2490
QFI-0506-08 5/16 3/8 .562 1/2 .032 .3125 .3148 .3747 .3753 .3106 .3115
QFI-0607-04 3/8 15/32 .687 1/4 .046 .4684 .4691 .3731 .3740
.3750 .3773
QFI-0607-08 3/8 15/32 .687 1/2 .046 .4684 .4691 .3731 .3740
QFI-0809-04 1/2 19/32 .875 1/4 .046 .5934 .5941 .4980 .4990
QFI-0809-08 1/2 19/32 .875 1/2 .046 .5003 .5030 .5934 .5941 .4980 .4990
QFI-0809-12 1/2 19/32 .875 3/4 .046 .5934 .5941 .4980 .4990
QFI-1011-12 5/8 23/32 .937 3/4 .046 .6253 .6280 .7184 .7192 .6230 .6240
QFI-1012-08 5/8 3/4 1.000 1/2 .062 .6263 .6290 .7500 .7510 .6240 .6250
QFI-1214-08 3/4 7/8 1.125 1/2 .062 .8747 .8755 .7479 .7491
QFI-1214-12 3/4 7/8 1.125 3/4 .062 .7507 .7541 .8747 .8755 .7479 .7491
QFI-1214-16 3/4 7/8 1.125 1 .062 .8747 .8755 .7479 .7491
QFI-1416-12 7/8 1 1.250 3/4 .062 .9997 1.0005 .8729 .8741
.8757 .8791
QFI-1416-16 7/8 1 1.250 1 .062 .9997 1.0005 .8729 .8741
QFI-1618-08 1 1 1/8 1.375 1/2 .062 1.1247 1.1255 .9979 .9991
QFI-1618-16 1 1 1/8 1.375 1 .062 1.0007 1.0041 1.1247 1.1255 .9979 .9991
QFI-1618-24 1 1 1/8 1.375 1 1/2 .062 1.1247 1.1255 .9979 .9991
QFI-1820-12 1 1/8 1 9/32 1.562 3/4 .078 1.2808 1.2818 1.1226 1.1238
1.1254 1.1288
QFI-1820-24 1 1/8 1 9/32 1.562 1 1/2 .078 1.2808 1.2818 1.1226 1.1238
QFI-2022-20 1 1/4 1 13/32 1.687 1 1/4 .078 1.4058 1.4068 1.2472 1.2488
1.2508 1.2548
QFI-2022-24 1 1/4 1 13/32 1.687 1 1/2 .078 1.4058 1.4068 1.2472 1.2488
QFI-2426-04 1 1/2 1 21/32 2.000 1/4 .078 1.6558 1.6568 1.4972 1.4988
1.5008 1.5048
QFI-2426-24 1 1/2 1 21/32 2.000 1 1/2 .078 1.6558 1.6568 1.4972 1.4988
QFI-2831-32 1 3/4 1 15/16 2.375 2 .093 1.7508 1.7547 1.9371 1.9381 1.7471 1.7487
QFI-3235-32 2 2 3/16 2.625 2 .093 2.0011 2.0057 2.1871 2.1883 1.9969 1.9981
QFI-3639-32 2 1/4 2 7/16 2.750 2 .093 2.2531 2.2577 2.4365 2.4377 2.2489 2.2507
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
QSM-0608-10 6.0 8.0 10.0 6.020 6.068 8.000 8.015 5.970 6.000
QSM-0810-08 8.0 10.0 8.0 8.025 8.083 10.000 10.015 7.964 8.000
QSM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
QSM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
12.032 12.102
QSM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000
QSM-1618-08 16.0 18.0 8.0 18.000 18.018 15.957 16.000
QSM-1618-12 16.0 18.0 12.0 16.032 16.102 18.000 18.018 15.957 16.000
QSM-1618-20 16.0 18.0 20.0 18.000 18.018 15.957 16.000
QSM-1820-20 18.0 20.0 20.0 18.032 18.102 20.000 20.021 17.957 18.000
QSM-2022-15 20.0 22.0 15.0 20.040 20.124 22.000 22.021 19.948 20.000
QSM-2023-15 20.0 23.0 15.0 23.000 23.021 19.948 20.000
QSM-2023-20 20.0 23.0 20.0 23.000 23.021 19.948 20.000
20.040 20.124
QSM-2023-25 20.0 23.0 25.0 23.000 23.021 19.948 20.000
QSM-2023-30 20.0 23.0 30.0 23.000 23.021 19.948 20.000
QSM-2225-15 22.0 25.0 15.0 22.040 22.124 25.000 25.021 21.948 22.000
QSM-2528-25 25.0 28.0 25.0 28.000 28.021 24.948 25.000
25.040 25.124
QSM-2528-48 25.0 28.0 48.0 28.000 28.021 24.948 25.000
QSM-3034-20 30.0 34.0 20.0 34.000 34.025 29.948 30.000
30.040 30.124
QSM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000
QSM-3539-15 35.0 39.0 15.0 39.000 39.025 34.938 35.000
QSM-3539-30 35.0 39.0 30.0 35.050 35.150 39.000 39.025 34.938 35.000
QSM-3539-50 35.0 39.0 50.0 39.000 39.025 34.938 35.000
QSM-4044-40 40.0 44.0 40.0 44.000 44.025 39.938 40.000
40.050 40.150
QSM-4044-47 40.0 44.0 47.0 44.000 44.025 39.938 40.000
QSM-4550-252 45.0 50.0 25.2 50.000 50.025 44.938 45.000
45.050 45.150
QSM-4550-50 45.0 50.0 50.0 50.000 50.025 44.938 45.000
QSM-5055-50 50.0 55.0 50.0 55.000 55.030 49.938 50.000
50.050 50.150
QSM-5055-60 50.0 55.0 60.0 55.000 55.030 49.938 50.000
QSM-5560-50 55.0 60.0 50.0 55.060 55.180 60.000 60.030 54.926 55.000
QSM-6065-50 60.0 65.0 50.0 60.060 60.180 65.000 65.030 59.926 60.000
QSM-6570-34 65.0 70.0 34.0 65.060 65.180 70.000 70.030 64.926 65.000
QSM-7075-50 70.0 75.0 50.0 70.060 70.180 75.000 75.030 69.926 70.000
QSM-8085-60 80.0 85.0 60.0 80.060 80.180 85.000 85.035 79.926 80.000
30°
Q F M -06 08-06
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
QFM-0608-04 6.0 8.0 12.0 4.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
QFM-0810-05 8.0 10.0 15.0 5.5 1.0 10.000 10.015 7.964 8.000
8.025 8.083
QFM-0810-06 8.0 10.0 15.0 6.0 1.0 10.000 10.015 7.964 8.000
QFM-1012-06 10.0 12.0 18.0 6.0 1.0 12.000 12.018 9.964 10.000
QFM-101215-08 10.0 12.0 15.0 8.0 1.0 12.000 12.018 9.964 10.000
10.025 10.083
QFM-1012-10 10.0 12.0 18.0 10.0 1.0 12.000 12.018 9.964 10.000
QFM-101215-035 10.0 12.0 15.0 3.5 1.0 12.000 12.018 9.964 10.000
QFM-1214-08 12.0 14.0 20.0 8.0 1.0 14.000 14.018 11.957 12.000
QFM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
QFM-1214-20 12.0 14.0 20.0 20.0 1.0 14.000 14.018 11.957 12.000
QFM-1416-12 14.0 16.0 22.0 12.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
QFM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
QFM-1820-12 18.0 20.0 26.0 12.0 1.0 18.032 18.102 20.000 20.021 17.957 18.000
QFM-2023-21 20.0 23.0 30.0 21.0 1.5 20.040 20.124 23.000 23.021 19.948 20.000
QFM-2528-21 25.0 28.0 35.0 21.5 1.5 28.000 28.021 24.948 25.000
25.040 25.124
QFM-2528-25 25.0 28.0 35.0 25.0 1.5 28.000 28.021 24.948 25.000
QFM-2629-05 26.0 29.0 35.0 5.0 1.5 29.000 29.021 25.948 26.000
26.040 26.124
QFM-2629-10 26.0 29.0 35.0 10.0 1.5 29.000 29.021 25.948 26.000
QFM-2730-20 27.0 30.0 38.0 20.0 1.5 27.040 27.124 30.000 30.021 26.948 27.000
QFM-3034-37 30.0 34.0 42.0 37.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
QFM-3539-26 35.0 39.0 47.0 26.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
QFM-4044-40 40.0 44.0 52.0 40.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
QFM-5055-50 50.0 55.0 63.0 50.0 2.0 50.050 50.150 55.000 55.030 49.938 50.000
QFM-6065-50 60.0 65.0 73.0 50.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
QFM-7075-50 70.0 75.0 83.0 75.0 2.0 70.060 70.180 75.000 75.030 69.926 70.000
d1
Type Dimensions
S
Order key
d2 Q T M -02 03-02
d6
Thickness s (mm)
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
Form T (washer)
iglide® material
h
d5
d4
Metric
d6
Part Number d1 d2 s d4 d5 h d6
h
-0.12 +0.375 +0.2
+0.25 -0.25 -0.05 +0.12
+0.12 +0.125 -0.2
QTM-2842-015 28.0 42.0 1.5 35.0 4.0 1.0 42.0
QTM-3254-015 32.0 54.0 1.5 43.0 4.0 1.0 54.0
QTM-3862-015 38.0 62.0 1.5 50.0 4.0 1.0 62.0
QTM-5278-020 52.0 78.0 2.0 65.0 4.0 1.5 78.0
iglide® Q2
• Dimensionally stable at high loads
• Wear Resistant
• Good price/performance ratio
517
iglide®
Q2 iglide® Q2 - For extreme loads
Wear resistant and robust
Shock resistant
Mechanical Properties
Modulus of elasticity psi 1,214,000 DIN 53457
Tensile strength at 68°F psi 34,810 DIN 53452
Compressive strength psi 18,850
Permissible static surface pressure (68°F) psi 17,400
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
9.0
Compressive Strength 8.0
The graph shows the elastic deformation of iglide ® Q2 during radial 7.0
loading. Plastic deformation can occur, this depends on the applied 6.0
pressure. 5.0
4.0
Deformation (%)
3.0
2.0
➤ Compressive strength, Page 63
1.0
0.0
0 3,626 7,252 10,150
Pressure (psi)
140°F 73°F
145
➤ Surface speed, Page 64
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Temperatures 23,200
20,300
iglide ® Q2 is a very temperature resistant material. The short 17,400
term temperature exposure limit is at 428°F. The long term upper 14,500
temperature limit of 266°F permits the broad use in applications 11,600
typical for the agricultural, utility vehicle or construction equipment
8,700
Pressure (psi)
fields. However, the pressure resistance of iglide® Q2 plain bearings
5,802
declines as temperatures increase. When considering temperatures,
2,901
the additional frictional heat in the bearing system must be taken into
account 0
68 86 104 122 140 158 176 194 212 230 248 266
Temperature (°F)
➤ Application temperatures, Page 67
0.6 0.35
0.30
0.5
0.25
Coefficient of friction (µ)
0.4
0.20
0.3 0.15
0.10
0.2
0.05
0.1
0.00
19.69 39.37 59.06 78.74 98.43 118.10 137.80
0 1,450 2,901 4,351 5,802 7,252 8,700 10,150 11,600
Shaft Materials 24
20
Generally we recommend the use of hardened shafts for use in high
16
load applications. Even at low to medium loads, iglide® Q2 will attain
increased service life with hard shafts as compared to soft shafts. 12
But for low load applications, the results are outstanding with free
Wear (µm/km)
8
cutting steel as well. For high loads, the wear in pivoting applications
4
is much lower than for rotations.
0
➤ Shaft Materials, Page 71 0.0 72 145 217 290
Pressure (psi)
HR Carbon Steel
40 5
Automatic steel
304 Stainless
20 Wear (µm/km) 4
0 3
145 290 1,450 2,091 6,527 11,020 14,500 2
440B
1050
Pressure (psi) 1
Rotating Oscillating 0
Wear with different shaft materials, oscillating and Wear of iglide® Q2, rotating applications with different
rotating movement p = 290 psi shaft materials, p=108 psi, v=98 fpm
Chemical Resistance
iglide® Q2 plain bearings have good resistance to chemicals. They are 0.6
resistant to most lubricants. The resistance is only limited for acids. 0.5
0.4
0.2
0.1
0
0 1.0 2.0 3.0 4.0 5.0
Radiation Resistance
Plain bearings made from iglide® Q2 are radiation resistant up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® Q2 plain bearings are permanently resistant to UV radiation.
Vacuum
The low water elements degas in the vacuum. Applications under vacuum conditions are possible with restrictions.
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
b1
Length b1 (inch)
f
Form S (sleeve)
iglide® material
.0197
30°
d1
For tolerance values
Inch
please refer to page 521
*Based on steel housing bore
Outer-Ø d2 (inch)
Inner-Ø d1 (inch)
f
Length b1 (inch)
r
iglide® material
Form F (flange)
b2
r = max. .0197 d3
For tolerance values
please refer to page 521
Inch
*Based on steel housing bore
Q2FI-0405-06 1/4 5/16 .500 3/8 .032 .3122 .3128 .2481 .2490
.2495 .2518
Q2FI-0405-08 1/4 5/16 .500 1/2 .032 .3122 .3128 .2481 .2490
Q2FI-0506-04 1/4 5/16 .500 1/4 .032 .3747 .3753 .3106 .3115
Q2FI-0506-06 1/4 5/16 .500 3/8 .032 .3120 .3143 .3747 .3753 .3106 .3115
Q2FI-0506-08 5/16 3/8 .562 1/2 .032 .3747 .3753 .3106 .3115
Q2FI-0607-04 3/8 15/32 .687 1/4 .046 .4684 .4691 .3731 .3740
Q2FI-0607-06 3/8 15/32 .687 3/8 .046 .4684 .4691 .3731 .3740
.3745 .3768
Q2FI-0607-08 3/8 15/32 .687 1/2 .046 .4684 .4691 .3731 .3740
Q2FI-0607-12 3/8 15/32 .687 3/4 .046 .4684 .4691 .3731 .3740
Q2FI-0708-08 7/16 17/32 .750 1/2 .046 .4371 .4399 .5309 .5316 .4355 .4365
Q2FI-0809-04 1/2 19/32 .875 1/4 .046 .5934 .5941 .4980 .4990
Q2FI-0809-06 1/2 19/32 .875 3/8 .046 .5934 .5941 .4980 .4990
Q2FI-0809-08 1/2 19/32 .875 1/2 .046 .4996 .5024 .5934 .5941 .4980 .4990
Q2FI-0809-12 1/2 19/32 .875 3/4 .046 .5934 .5941 .4980 .4990
Q2FI-0809-16 1/2 19/32 .875 1 .046 .5934 .5941 .4980 .4990
Q2FI-1011-08 5/8 23/32 .937 1/2 .046 .7184 .7192 .6230 .6240
Q2FI-1011-12 5/8 23/32 .937 3/4 .046 .6246 .6274 .7184 .7192 .6230 .6240
Q2FI-1011-16 5/8 23/32 .937 1 .046 .7184 .7192 .6230 .6240
Q2FI-1214-08 3/4 7/8 1.125 1/2 .062 .8747 .8755 .7479 .7491
Q2FI-1214-12 3/4 7/8 1.125 3/4 .062 .7499 .7532 .8747 .8755 .7479 .7491
Q2FI-1214-16 3/4 7/8 1.125 1 .062 .8747 .8755 .7479 .7491
Q2FI-1416-08 7/8 1 1.250 1/2 .062 .9997 1.0005 .8729 .8741
Q2FI-1416-12 7/8 1 1.250 3/4 .062 .8749 .8782 .9997 1.0005 .8729 .8741
Q2FI-1416-16 7/8 1 1.250 1 .062 .9997 1.0005 .8729 .8741
Q2FI-1618-08 1 1 1/8 1.375 1/2 .062 1.1247 1.1255 .9979 .9991
Q2FI-1618-12 1 1 1/8 1.375 3/4 .062 .9999 1.0032 1.1247 1.1255 .9979 .9991
Q2FI-1618-16 1 1 1/8 1.375 1 .062 1.1247 1.1255 .9979 .9991
Q2FI-2022-16 1 1/4 1 13/32 1.687 1 .078 1.4058 1.4068 1.2472 1.2488
1.2498 1.2537
Q2FI-2022-20 1 1/4 1 13/32 1.687 1 1/4 .078 1.4058 1.4068 1.2472 1.2488
Q2FI-2426-16 1 1/2 1 21/32 2.000 1 .078 1.6558 1.6568 1.4972 1.4988
1.4998 1.5037
Q2FI-2426-24 1 1/2 1 21/32 2.000 1 1/2 .078 1.6558 1.6568 1.4972 1.4988
Q2FI-2831-32 1 3/4 1 15/16 2.375 2 .093 1.7497 1.7536 1.9371 1.9381 1.7471 1.7487
Q2FI-3235-16 2 2 3/16 2.625 1 .093 2.1871 2.1883 1.9969 1.9981
1.9993 2.0040
Q2FI-3235-32 2 2 3/16 2.625 2 .093 2.1871 2.1883 1.9969 1.9981
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Q2SM-0507-05 5.0 7.0 5.0 5.020 5.068 7.000 7.015 4.970 5.000
Q2SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
Q2SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
Q2SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
Q2SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
Q2SM-1517-15 15.0 17.0 15.0 15.032 15.102 17.000 17.018 14.957 15.000
Q2SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
Q2SM-2023-20 20.0 23.0 20.0 23.000 23.021 19.948 20.000
20.040 20.124
Q2SM-2023-30 20.0 23.0 30.0 23.000 23.021 19.948 20.000
Q2SM-2528-20 25.0 28.0 20.0 25.040 25.124 28.000 28.021 24.948 25.000
Q2SM-3034-30 30.0 34.0 30.0 30.040 30.124 34.000 34.025 29.948 30.000
Q2SM-3240-40 32.0 40.0 40.0 32.050 32.150 40.000 40.025 31.938 32.000
Q2SM-3539-40 35.0 39.0 40.0 35.050 35.150 39.000 39.025 34.938 35.000
Q2SM-4044-40 40.0 44.0 40.0 40.050 40.150 44.000 44.025 39.938 40.000
Q2SM-4550-50 45.0 50.0 50.0 45.050 45.150 50.000 50.025 44.938 45.000
Q2SM-5055-50 50.0 55.0 50.0 50.050 50.150 55.000 55.030 49.938 50.000
Q2SM-6065-60 60.0 65.0 60.0 60.060 60.180 65.000 65.030 59.926 60.000
Q2SM-6570-60 65.0 70.0 60.0 65.060 65.180 70.000 70.030 64.926 65.000
Q2SM-7075-60 70.0 75.0 60.0 70.060 70.180 75.000 75.030 69.926 70.000
Q2SM-7580-40 75.0 80.0 40.0 75.060 75.180 80.000 80.030 74.926 75.000
30°
Q2 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.
Q2FM-0507-05 5.0 7.0 11.0 5.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
Q2FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
Q2FM-0810-03 8.0 10.0 15.0 3.0 1.0 10.000 10.015 7.964 8.000
8.025 8.083
Q2FM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.015 7.964 8.000
Q2FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
Q2FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
Q2FM-1416-05 14.0 16.0 22.0 5.0 1.0 14.032 14.102 16.000 16.018 13.957 14.000
Q2FM-1517-17 15.0 17.0 23.0 17.0 1.0 15.032 15.102 17.000 17.018 14.957 15.000
Q2FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
Q2FM-2023-12 20.0 23.0 30.0 1.0 1.5 23.000 23.021 19.948 20.000
20.040 20.124
Q2FM-2023-21 20.0 23.0 30.0 21.5 1.5 23.000 23.021 19.948 20.000
Q2FM-2528-21 25.0 28.0 35.0 21.5 1.5 25.040 25.124 28.000 28.021 24.948 25.000
Q2FM-3034-37 30.0 34.0 42.0 40.0 2.0 34.000 34.025 29.948 30.000
30.040 30.124
Q2FM-3034-40 30.0 34.0 42.0 40.0 2.0 34.000 34.025 29.948 30.000
Q2FM-3539-40 35.0 39.0 47.0 40.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
Q2FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
Q2FM-4550-50 45.0 50.0 58.0 50.0 2.5 45.050 45.150 50.000 50.025 44.938 45.000
Q2FM-5055-10 50.0 55.0 63.0 10.0 2.0 55.000 55.030 49.938 50.000
50.050 50.150
Q2FM-5055-50 50.0 55.0 63.0 50.0 2.0 55.000 55.030 49.938 50.000
Q2FM-6065-60 60.0 65.0 73.0 50.0 2.0 60.060 60.180 65.000 65.030 59.926 60.000
Q2FM-8085-100 80.0 85.0 93.0 100.0 2.5 80.060 80.180 85.000 85.035 79.926 80.000
iglide® TX1
• Up to 29,000 psi static and 20,300 psi dynamic
• Wear resistant and dimensionally stable
• Good media resistance
527
iglide®
TX1
iglide® TX1 - Heavy duty
Up to 29,000 psi
Self-lubricating and iglide® TX1 offers outstanding rigidity and durability especially
maintenance-free under high radial loads during pivoting operations. Thanks
to the closed-loop wound structure, excellent dimensional
stability is even achieved in cases of major impacts.
Mechanical Properties
Modulus of elasticity psi 1,740,000 DIN 53457
Tensile strength at 68°F psi 7,977 DIN 53452
Compressive strength psi 31,910
Permissible static surface pressure (68°F) psi 29,000
Shore D-hardness 94 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1 x 1011 DIN IEC 93
Surface resistance Ω > 1 x 1013 DIN 53482
8.0
Compressive Strength 7.0
6.0
With increasing temperatures, the compressive strength of iglide ®
5.0
TX1 plain bearings decreases. At the short-term permitted application
4.0
temperature of 338°F, the permitted surface pressure is still 14,500 psi.
Deformation (%)
3.0
The recommended mximum surface pressure is a mechanical material
parameter. No conclusions regarding the tribological properties can be 2.0
drawn from this. The graph shows the elastic deformation of iglide® 1.0
145
➤ Surface speed, Page 64
➤ pv value, Page 65
14.5
.197 1.97 19.7 197 1,969
Temperatures
29,010
iglide® TX1 is a very temperature resistant material. The long-term upper
25,382
temperature limit of +248 °F permits the broad use in applications typical
21,756
for the agricultural, utility vehicle or construction equipment sectors. The
18,130
press-in and press-out forces of iglide® TX1 bearings are extremely high
over the entire temperature range. As a result, additional axial securing is 17,400
generally unnecessary. Although the levels still remain very high, a certain 10,880
Pressure (psi)
decline can, however, be observed at temperatures above +212 °F. In some 7,252
cases, axial securing is therefore recommended from this temperature. 3,626
When considering temperatures, the additional frictional heat in the bearing 0
system must be taken into account. 68 104 140 176 212 248 284 320 356
Temperature (°F)
➤ Application temperatures, Page 67
0.25
Coefficient of friction (µ)
0.30
0.20
0.20 0.15
0.10
0.10
0.05
0
0
0 1,450 2,901 4,351 5,802 7,252 8,702 10,150
0 19.69 39.37 59.06 78.74
Coefficient of friction as a result of the surface speed; Coefficient of friction as a result of the load, v = 1.97 fpm
load = 108 psi constant
Shaft Materials
40
In high load applications, we generally recommend the use of hardened
shafts. This particularly applies when using iglide® TX1. However, acceptable
wear rates are also achieved on soft shafts with heavy-duty pivoting of less 30
than 14,500 psi. The comparison of the wear rate during rotation and
HR carbon steel
Machinery Steel
Chromax 482H
TX1 lies in heavy-duty pivoting.
Chromax 280X
304 Stainless
Wear (µm/km)
➤ Shaft Materials, Page 71 10
1050
0
50
20
Wear (µm/km)
10
0
0 2,901 5,802 8,702 11,600 14,500 17,400 20,310
Pressure (psi)
Rotating Oscillating
Medium Resistance
Alcohol 0
Hydrocarbon, chlorinated +
Greases, oils without additives +
Fuels +
Weak acids +
Strong acids –
Weak alkaline +
Strong alkaline –
+ resistant, 0 conditionally resistant, – not resistant
Radiation Resistance
Plain bearings made from iglide® TX1 are resistant to radiation up to an intensity of applications 2 · 102 Gy.
UV-Resistance
iglide® TX1 plain bearings are permanently resistant to UV radiation.
Vacuum
In a vacuum, any moisture content will outgas. Applications under vacuum conditions are possible to a limited extent.
iglide® TX1
Electrical Properties Specific volume resistance > 1 x 1011 Ωcm
iglide TX1 plain bearings are electrically insulating
®
Surface resistance > 1 x 1013 Ω
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
The biopolymer –
iglide® N54
➤ Page 573
Ø 2 to 70 mm
mm
more dimensions on request
Heavy-duty on soft shafts –
iglide® Q290
➤ Page 597
The low demand for space and freedom from corrosion of iglide® The requirements profile for plain bearings is extremely demanding.
plain bearings qualified them for use in this model. They must be resistant to weather for decades, be able to deal with
dirt and moisture, and must be easy to assemble.
By modifying the plastic/metal plain bearing partners to the plain Hand prothesis: All the axes involved in the movement are
bearing partners plastic/plastic, a conversion of the integral design supported by plastic bearings.
was achievable.
The bearings do not have to be lubricated and they dampen the iglide® plain bearings guarantee smooth valve movement and
vibrations in the bearing housings without noticeably wearing down. increase system productivity thanks to reliability and load capacity.
Standard Bar speedigus® Long life For high Dirt Low Chemical
catalog stock material in dry loads resistant coefficient resistant
range operation of friction
iglidur® F l l
iglide® F2 l l l l
iglide® H4 l l l l l l
iglide® UW l
iglide® N54 l
iglide® G V0 l l l
iglide® J2 l l
iglide® Q290 l
Low water For under Edge Vibrations Food Temperatures Temperatures Economic
absorption water use pressure dampening suitable up to up to
+194 °F +302 °F
iglide® F l
iglide® F2 l l l
iglide® H4 l l l l l l
iglide® UW l l l l
iglide® N54
iglide® G V0 l l
iglide® J2 l l l l
iglide® Q290 l l
iglide® F 539
iglide® F2 549
iglide® H4 557
iglide® UW 565
iglide® G V0 581
iglide® J2 589
iglide® F 6 1 539
iglide® F2 3 3 549
iglide® H4 3 5 557
iglide® UW 3 6 565
iglide® G V0 6 6 581
iglide® J2 7 3 589
Coefficients of friction of iglide® bearings Wear of iglide® bearings against steel rotating,
against steel rotating, p = 145 psi v = 59 fpm p = 145 psi
Average of all the seven sliding Average of all the seven sliding
combinations tested combinations tested
Coefficient of friction of best combination Wear of best combination
Shaft material:
1 = 1050, case hardened 4 = Free-cutting steel 7 = 440B Stainless
539
iglide®
F
iglide® F - Electrically conductive
Highly pressure resistant
Outstanding rigidity and hardness as well as high
conductivity: iglide ® F bearings can only be used in
High compressive strength dry operations to a limited extent, but offer their full
mechanical benefits when lubricated with oil or grease.
High pv value
Mechanical Properties
Modulus of elasticity psi 1,682,000 DIN 53457
Tensile strength at 68°F psi 37,710 DIN 53452
Compressive strength psi 14,210
Permissible static surface pressure (68°F) psi 15,230
Shore D-hardness 84 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 103 DIN IEC 93
Surface resistance Ω < 102 DIN 53482
Compressive Strength 10
8
At room temperature, they can handle loads up to 15,225 psi.
The graph shows the elastic deformation of iglide® F for radial loads. 6
Deformation (%)
Pressure (psi)
140°F 73°F
Deformation under load and temperature
Permissible pv values for iglide® F running dry against a steel Rotating 157 295
shaft, at 68°F
Oscillating 118 216
Linear 590 1181
Temperatures
23,210
The ambient temperatures greatly affect the properties of plain bearings.
20,310
The maximum permissible short-term temperature is 356°F. In long-
17,400
term operation, 284°F may not be exceeded.
14,500
With increasing temperatures, the compressive strength of iglide® F
11,600
plain bearings decreases. The graph shows this relationship. The wear
also increases. 8702
Pressure (psi)
5802
➤ Application temperatures, Page 67 2901
0
68 122 176 248 284
iglide® F Application Temperature
Temperature (°F)
Minimum -40°F
Max. long-term +284°F Recommended maximum permissible static surface
Max. short-term +356°F pressure of iglide® F as a result of the temperature
Additional axial securing +221°F
Temperature iglide® F
0.6 0.5
Coefficient of friction (µ)
Coefficient of friction (µ)
0.4
0.5
0.3
0.2
0.4
0.1
0.3 0.0
9.84 19.69 29.53 39.37 49.21 59.06 68.90 0 1450 2901 4351 5802 7252 8702 10150 11600
Coefficients of friction of iglide F as a function of the ® Coefficients of friction of iglide® F as a function of the
running speed; p = 108 psi load, v = 1.96 fpm
Shaft Materials 40
The graphs show results of testing different shaft materials with plain
bearings made of iglide® F. 30
In the lowest load range, the hard-chromed shaft proves to be the best
Wear (µm/km)
partner in rotating applications with iglide® F plain bearings.
20
The behavior is different in oscillating movements. With much higher wear
values than for rotation, the 303 Stainless Steel shaft and the hard-chromed
shaft are better than the Cold Rolled Steel shaft even at 290 psi. If the shaft 10
material you plan to use is not contained in this list, please contact us
0
➤ Shaft Materials, Page 71 1050 Hard 304 Stainless HR Carbon
Steel Chromed Steel Steel
Rotating Oscillating
8
12 7
6
10
Hard anodized aluminum
8 4
Automatic screw steel
Wear (µm/km)
6
HR Carbon steel
2
304 Stainless
1
4
0
36.26 108 145 290
440B
2
1050
Pressure (psi)
0
1050 Steel 304 Stainless
HR carbon steel Hard chromed
Wear of iglide® F, rotating applications with different
shaft materials, p=108 psi, v=98 fpm Wear of iglide® F with different shaft materials in rota-
tional applications, as a function of the pressure
1.50
Medium Resistance
Alcohol + to 0 1.25
Radiation Resistance
Plain bearings made from iglide® F are resistant to radiation up to an intensity of 3 x 102 Gy.
UV-Resistance
iglide® F plain bearings are permanently resistance to UV radiation.
Vacuum
In a vacuum environment, existing moisture is released as vapor. Therefore, only dehumidified bearings made of iglide® F are suitable for the vacuum.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
FSM-0203-03 2.0 3.5 3.0 2.020 2.080 3.500 3.510 1.975 2.000
FSM-0304-03 3.0 4.5 3.0 3.020 3.080 4.500 4.512 2.970 3.000
FSM-0405-04 4.0 5.5 4.0 4.030 4.105 5.500 5.512 3.970 4.000
FSM-0507-05 5.0 7.0 5.0 7.000 7.015 4.964 5.000
5.030 5.105
FSM-0507-08 5.0 7.0 8.0 7.000 7.015 4.964 5.000
FSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.964 6.000
FSM-0608-08 6.0 8.0 8.0 8.000 8.015 5.964 6.000
6.030 6.105
FSM-0608-10 6.0 8.0 10.0 8.000 8.015 5.964 6.000
FSM-0608-13 6.0 8.0 13.8 8.000 8.015 5.964 6.000
FSM-0709-10 7.0 9.0 10.0 9.000 9.015 6.964 7.000
7.040 7.130
FSM-0709-12 7.0 9.0 12.0 9.000 9.015 6.964 7.000
FSM-0810-08 8.0 10.0 8.0 10.000 10.015 7.964 8.000
FSM-0810-10 8.0 10.0 10.0 8.040 8.130 10.000 10.015 7.964 8.000
FSM-0810-15 8.0 10.0 15.0 10.000 10.015 7.964 8.000
FSM-1012-06 10.0 12.0 9.0 12.000 12.018 9.957 10.000
FSM-1012-09 10.0 12.0 9.0 10.040 10.130 12.000 12.018 9.957 10.000
FSM-1012-10 10.0 12.0 10.0 12.000 12.018 9.957 10.000
FSM-1214-10 12.0 14.0 10.0 14.000 14.018 11.957 12.000
12.050 12.160
FSM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000
FSM-1315-20 13.0 15.0 20.0 13.050 13.160 15.000 15.018 12.957 13.000
FSM-1416-15 14.0 16.0 15.0 14.050 14.160 16.000 16.018 13.957 14.000
FSM-1517-15 15.0 17.0 15.0 17.000 17.018 14.957 15.000
15.050 15.160
FSM-1517-20 15.0 17.0 20.0 17.000 17.018 14.957 15.000
FSM-1618-15 16.0 18.0 15.0 16.050 16.160 18.000 18.018 15.957 16.000
FSM-1820-12 18.0 20.0 12.0 20.000 20.021 17.948 18.000
FSM-1820-15 18.0 20.0 15.0 18.050 18.160 20.000 20.021 17.948 18.000
FSM-1820-20 18.0 20.0 20.0 20.000 20.021 17.948 18.000
FSM-2022-14 20.0 22.0 14.5 22.000 22.021 19.948 20.000
20.065 20.195
FSM-2022-20 20.0 22.0 20.0 22.000 22.021 19.948 20.000
FSM-2023-15 20.0 23.0 15.0 23.000 23.021 19.948 20.000
20.065 20.195
FSM-2023-20 20.0 23.0 20.0 23.000 23.021 19.948 20.000
FSM-2225-15 22.0 25.0 15.0 22.065 22.195 25.000 25.021 22.948 22.000
FSM-2528-20 25.0 28.0 20.0 25.065 25.195 28.000 28.021 24.948 25.000
FSM-2832-20 28.0 32.0 20.0 32.000 32.025 27.948 28.000
28.065 28.195
FSM-2832-30 28.0 32.0 30.0 32.000 32.025 27.948 28.000
FSM-3034-20 30.0 34.0 20.0 34.000 34.025 29.938 30.000
30.065 30.195
FSM-3034-30 30.0 34.0 30.0 34.000 34.025 29.938 30.000
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
FSM-3034-40 30.0 34.0 40.0 30.065 30.195 34.000 34.025 29.938 30.000
FSM-3236-30 32.0 36.0 30.0 32.080 32.240 36.000 36.025 31.938 32.000
FSM-3539-30 35.0 39.0 30.0 39.000 39.025 34.938 35.000
35.080 35.240
FSM-3539-40 35.0 39.0 40.0 39.000 39.025 34.938 35.000
FSM-4044-30 40.0 44.0 30.0 44.000 44.025 39.938 40.000
40.080 40.240
FSM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000
FSM-4550-50 45.0 50.0 50.0 45.080 45.240 50.000 50.025 44.938 45.000
FSM-5055-40 50.0 55.0 40.0 50.080 50.240 55.000 55.030 49.938 50.000
FSM-5560-50 55.0 60.0 50.0 55.100 55.290 60.000 60.030 54.926 55.000
FSM-6065-60 60.0 65.0 60.0 60.100 60.290 65.000 65.030 59.926 60.000
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
r
iglide® material
Form F (flange)
r = max. 0.5
b2
For tolerance values
d3 please refer to page 543
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
FFM-0405-04 4.0 5.5 9.5 4.0 0.75 5.000 5.012 3.970 4.000
4.030 4.105
FFM-0405-06 4.0 5.5 9.5 6.0 0.75 5.000 5.012 3.970 4.000
FFM-0507-05 5.0 7.0 11.0 5.0 1.0 5.030 5.105 7.000 7.015 4.970 5.000
FFM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000
6.030 6.105
FFM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
FFM-0810-06 8.0 10.0 15.0 6.0 1.0 10.000 10.015 7.964 8.000
8.040 8.130
FFM-0810-09 8.0 10.0 15.0 9.0 1.0 10.000 10.015 7.964 8.000
FFM-1012-06 10.0 12.0 18.0 6.0 1.0 12.000 12.018 9.964 10.000
FFM-1012-08 10.0 12.0 18.0 8.0 1.0 12.000 12.018 9.964 10.000
FFM-1012-09 10.0 12.0 18.0 9.0 1.0 10.040 10.130 12.000 12.018 9.964 10.000
FFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000
FFM-1012-18 10.0 12.0 18.0 18.0 1.0 12.000 12.018 9.964 10.000
FFM-1214-09 12.0 14.0 20.0 9.0 1.0 14.000 14.018 11.957 12.000
12.050 12.160
FFM-1214-12 12.0 14.0 20.0 12.0 1.0 14.000 14.018 11.957 12.000
FFM-1416-12 14.0 16.0 22.0 12.0 1.0 16.000 16.018 13.957 14.000
14.050 14.160
FFM-1416-17 14.0 16.0 22.0 17.0 1.0 16.000 16.018 13.957 14.000
FFM-1517-12 15.0 17.0 23.0 12.0 1.0 17.000 17.018 14.957 15.000
15.050 15.160
FFM-1517-17 15.0 17.0 23.0 17.0 1.0 17.000 17.018 14.957 15.000
FFM-1618-17 16.0 18.0 24.0 17.0 1.0 16.050 16.160 18.000 18.018 15.957 16.000
FFM-1820-12 18.0 20.0 26.0 12.0 1.0 20.000 20.021 17.957 18.000
18.050 18.160
FFM-1820-17 18.0 20.0 26.0 17.0 1.0 20.000 20.021 17.957 18.000
FFM-2023-21 20.0 23.0 30.0 21.0 1.5 20.065 20.195 23.000 23.021 19.948 20.000
FFM-2528-21 25.0 28.0 35.0 21.0 1.5 25.065 25.195 28.000 28.021 24.948 25.000
FFM-3034-26 30.0 34.0 42.0 26.0 2.0 30.065 30.195 34.000 34.025 29.948 30.000
FFM-3236-26 32.0 36.0 45.0 26.0 2.0 32.080 32.240 36.000 36.025 31.938 32.000
FFM-3539-06 35.0 39.0 47.0 6.0 2.0 39.000 39.025 34.938 35.000
35.080 35.240
FFM-3539-16 35.0 39.0 47.0 16.0 2.0 39.000 39.025 34.938 35.000
FFM-3539-26 35.0 39.0 47.0 26.0 2.0 35.080 35.240 39.000 39.025 34.938 35.000
FFM-4044-30 40.0 44.0 52.0 30.0 2.0 44.000 44.025 39.938 40.000
40.080 40.240
FFM-4044-40 40.0 44.0 52.0 40.0 2.0 44.000 44.025 39.938 40.000
FFM-4550-50 45.0 50.0 58.0 50.0 2.0 45.080 45.240 50.000 50.025 44.935 45.000
FFM-5055-10 50.0 55.0 63.0 10.0 2.0 55.000 55.030 49.938 50.000
50.080 50.240
FFM-5055-40 50.0 55.0 63.0 40.0 2.0 55.000 55.030 49.938 50.000
FFM-6065-40 60.0 65.0 73.0 40.0 2.0 60.100 60.290 65.000 65.030 59.926 60.000
FFM-7075-40 70.0 75.0 83.0 40.0 2.0 70.100 70.290 75.000 75.030 69.926 70.000
549
iglide®
F2 iglide® F2 - ESD compatible
Wear resistant and conductive
Used to prevent
electro-static charges iglide® F2 helps to prevent electrostatic charging. Good
resistance to media and temperature, suitable even in
wet conditions due to low moisture absorption and good
universal wear values pave the way for a wide range of
applications.
ESD compatible
Also suitable for wet applications l When the bearing should be electrically discharging
l When a universal bearing is required for a broad
application range
Self-lubricating
and maintenance-free
Mechanical Properties
Modulus of elasticity psi 1,076,000 DIN 53457
Tensile strength at 68°F psi 13,490 DIN 53452
Compressive strength psi 8,847
Permissible static surface pressure (68°F) psi 6,817
Shore D-hardness 72 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 109 DIN IEC 93
Surface resistance Ω < 109 DIN 53482
7
Compressive Strength 6
With increasing temperatures, the compressive strength of iglide® F2 5
bearings decreases. The recommended maximum surface pressure is a
4
mechanical material parameter. No conclusions regarding the tribological
3
Deformation (%)
properties can be drawn from this. The graph shows the elastic deformation
of iglide® F2 at radial loads. A plastic deformation can be negligible up to 2
this value. However, it is also dependent on the service time. 1
0
➤ Compressive strength, Page 63 0 2,176 4,351 6,527
Pressure (psi)
140°F 73°F
Deformation under load and temperature
14.5
.197 1.97 19.7 197 1,969
Surface Speed (fpm) Continuous Short Term
fpm fpm
Permissible pv values for iglide® F2 running dry against
Rotating 157 275
a steel shaft, at 68°F
Oscillating 137 216
Linear 590 984
Maximum surface speeds
Temperatures 10,150
8,702
The ambient temperatures strongly influence the performance of the
bearings. With increasing temperatures, the compressive strength of 7,252
iglide® F2 bearings decreases. The graph shows this inverse relationship. 5,802
At temperatures over +158 °F an additional securing is required.
4,351
Pressure (psi)
➤ Application temperatures, Page 67 2,901
1,450
0
68 104 140 176 212 248
Temperature (°F)
0.6 0.5
0.5
0.4
0.4
Coefficient of friction (µ)
0.3
0.3
0.2
0.2
0.1 0.1
0.0
0.0
19.69 39.37 59.06 78.74 98.43 118.11 137.80
0 1,450 2,901 4,351 5,802 7,252
Surface speed (fpm)
Pressure (psi)
The graphs show the results of testing different shaft materials with plain 400
bearings made from iglide® F2.
With lower loads, cutting steel and hard anodized aluminum shafts, as 300
Wear (µm/km)
respect to wear.
100
The graph to the right shows a significantly less wear in rotation compared
to pivoting movements over the entire load range. 0
725 1,450 2,901 4,351 5,802
➤ Shaft Materials, Page 71 Pressure (psi)
Rotating Oscillating
10
Hard anodized aluminum
8
Automatic screw steel
6
HR Carbon Steel
304 Stainless
Wear (µm/km)
2
440B
1050
Moisture absorption
0.10
0.04
0.02
0.00
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40
Radiation Resistance
Plain bearings made from iglide® F2 are resistant to radiation up to an intensity of applications 3 · 102 Gy.
UV-Resistance
iglide® F2 plain bearings are partially resistant to UV radiation.
Vacuum
iglide® F2 plain bearings outgas in a vacuum. Use in vacuum is only possible with dehumidified bearings.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
F2SM-0507-10 5.0 7.0 10.0 5.020 5.068 7.000 7.015 4.970 5.000
F2SM-0608-06 6.0 8.0 6.0 6.020 6.058 8.000 8.015 5.970 6.000
F2SM-0709-10 7.0 9.0 10.0 7.025 7.083 9.000 9.015 6.964 7.000
F2SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
F2SM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000
10.025 10.083
F2SM-1012-15 10.0 12.0 15.0 12.000 12.018 9.964 10.000
F2SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
F2SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
F2SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
F2 F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
F2FM-0405-04 4.0 5.5 9.5 4.0 0.75 4.010 4.058 5.000 5.012 3.970 4.000
F2FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
F2FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
F2FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
F2FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
F2FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
F2FM-2023-21 20.0 23.0 30.0 21.0 1.5 20.040 20.124 23.000 23.021 19.948 20.000
psi
iglide® H4
• Low coefficients of friction
• High wear resistance
• High temperature resistance -40°F to +392°F
• High chemical resistance
557
iglide®
H4 iglide® H4 - The automotive standard
For temperatures up to 392°F
Low coefficients of friction Very cost-efficient, high temperature material with good
dry-operation properties and “engine compartment resis-
tance”.
Mechanical Properties
Modulus of elasticity psi 1,088,000 DIN 53457
Tensile strength at 68°F psi 17,400 DIN 53452
Compressive strength psi 7,252
Permissible static surface pressure (68°F) psi 9,427
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
5.0
Compressive Strength
The graph shows the elastic deformation of iglide® H4 when subjected
Deformation in %
to radial loads. Among the iglide® H materials, iglide® H4 is the one with
the lowest modulus of elasticity. This is beneficial for applications with 2.5
edge loads and vibrations. Where a high static compressive strength
is concerned, the other iglide® H bearing types are advantageous.
0.0
➤ Compressive strength, Page 63 0 2901 5802 9427
140°F 73.4°F
Pressure (psi)
Deformation under load and temperature
145
value.
Temperatures 10150
8702
iglide ® H4 is a temperature resistant material. The short-term
maximum permissible temperature is 464°F, and therefore allows for 7252
the use of iglide® H4 plain bearings in applications where the bearings 5802
for instance undergo a drying process without further loading.
4351
The compressive strength of iglide ® H4, however, decreases with
Pressure (psi)
increasing temperatures. 2901
The graph clarifies this relationship. At these high temperatures, the 1450
additional frictional heat in the bearing system has to be considered.
0
68 122 176 248 302 392
➤ Application temperatures, Page 67
Temperature (°F)
0.5 0.7
0.6
0.4
0.5
Coefficient of friction (µ)
0.4
0.3
0.3
0.2 0.2
0.1
0.1
0.0
9.84 19.69 29.53 39.37 49.21 59.06
0 1450 2901 4351 5802 7252 8702 10150 11600
Surface speed (fpm) Pressure (psi)
200
180
Shaft Materials 160
140
As well as being an economic bearing, iglide® H4 offers further savings 120
when the shaft material is selected. Many alternatives are possible, 100
although the correct shaft is also dependent on the type of application. 80
Wear (µm/km)
There is no general rule to say if iglide® H4 is better with hard or soft 60
shafts. However, it is true that oscillating applications produce better 40
wear results than rotating applications. When used in rotation, the 20
24
10
9 20
8
16
7
1050, hardened chromed
Hard anodized aluminum
6
Automatic screw steel
12
5
Wear (µm/km)
HR Carbon Steel
Wear (µm/km)
4 8
304 Stainless
3
4
2
440B
1050
1 0
0 0.0 72 145 217 290
Pressure (psi)
Wear of iglide® H4, rotating applications with different 1050 steel HR Carbon Steel 304 Stainless Hard chromed
Chemical Resistance
0.10
Radiation Resistance
iglide® H4 withstands neutron radiation as well as gamma radiation without noticeable losses of its excellent mechanical characteristics. iglide® H4
plain bearings are radiation resistant up to a radiation intensity of 2 x 102 Gy.
UV-Resistance
iglide® H4 plain bearings change under the influence of UV radiation and other climatic influences. The surface gets rougher, and the compressive
strength decreases. The use of iglide® H4 in applications directly exposed to atmospheric conditions should therefore be tested.
Vacuum
In a vacuum environment, existing moisture will outgas. Due to the low moisture absorption of iglide® H4, this means that use in a vacuum is usually
possible.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
H4SM-0405-04 4.0 5.5 4.0 4.010 4.058 5.500 5.512 3.970 4.000
H4SM-0608-08 6.0 8.0 8.0 6.010 6.058 8.000 8.015 5.970 6.000
H4SM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000
8.013 8.071
H4SM-0810-20 8.0 10.0 20.0 10.000 10.015 7.964 8.000
H4SM-1618-20 16.0 18.0 20.0 16.016 16.086 18.000 18.018 15.957 16.000
H4SM-1820-15 18.0 20.0 15.0 18.016 18.086 20.000 20.021 17.957 18.000
H4SM-2022-15 20.0 22.0 15.0 20.020 20.104 23.000 23.021 19.948 20.000
H4SM-3943-40 39.0 43.0 40.0 39.025 39.125 43.000 43.025 38.938 39.000
30°
H4 F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
H4FM-0405-04 4.0 5.5 9.5 4.0 0.75 4.010 4.058 5.500 5.512 3.970 4.000
H4FM-0608-08 6.0 8.0 12.0 8.0 1.0 8.000 8.015 5.970 6.000
6.010 6.058
H4FM-060810-20 6.0 10.0 12.0 20.0 1.0 8.000 8.015 5.970 6.000
H4FM-0810-10 8.0 10.0 15.0 9.0 1.0 8.013 8.071 10.000 10.015 7.964 8.000
H4FM-1012-05 10.0 12.0 18.0 5.0 1.0 12.000 12.018 9.964 10.000
H4FM-1012-12 10.0 12.0 18.0 12.0 1.0 10.013 10.071 12.000 12.018 9.964 10.000
H4FM-101218-25 10.0 12.0 18.0 25.0 1.0 12.000 12.018 9.964 10.000
H4FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.016 12.086 14.000 14.018 11.957 12.000
H4FM-1517-12 15.0 17.0 23.0 12.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000
H4FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.016 16.086 18.000 18.018 15.957 16.000
H4FM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 18.000 18.018 17.957 18.000
H4FM-2023-21 20.0 23.0 30.0 21.0 1.5 20.020 20.104 23.000 23.021 19.948 20.000
H4FM-2528-21 25.0 28.0 35.0 21.0 1.5 25.020 25.104 28.000 28.021 24.948 25.000
H4FM-3034-30 30.0 34.0 42.0 30.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000
H4FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000
565
iglide®
UW iglide® UW - The underwater endurance runner
For fast rotation under water
For underwater applications The best iglide® bearings for underwater applications.
Extremely wear resistant under water, tested and
maintenance-free. The first choice for pumping applications.
Mechanical Properties
Modulus of elasticity psi 1,392,000 DIN 53457
Tensile strength at 68°F psi 13,050 DIN 53452
Compressive strength psi 10,150
Permissible static surface pressure (68°F) psi 5,802
Shore D-hardness 78 DIN 53505
Electrical Properties
Specific volume resistance Ωcm < 105 DIN IEC 93
Surface resistance Ω < 105 DIN 53482
7
Compressive Strength 6
The graph shows the permissible bearing loads at the respective 5
temperatures. It can be said that iglide ® UW plain bearings are not
4
very suitable for high loads. Normally in underwater applications there
3
Deformation (%)
Pressure (psi)
➤ Compressive strength, Page 63
140°F 73°F
Temperatures 5,802
5,076
iglide® UW plain bearings are recommended for the low temperature
4,351
range. The bearing temperature can be up to 194°F, although the
3,626
frictional heat must also be considered, especially when running dry.
In underwater applications, the fluid aids heat dissipation, so in this 2,901
case the temperature of the fluid is of greater importance. 2,176
Pressure (psi)
1,450
➤ Application temperatures, Page 67
725
0
68 86 104 122 140 158 176 194
Temperature °F
0.5 0.7
0.6
0.4
Coefficient of friction µ
0.5
Coefficient of friction µ
0.4
0.3
0.3
0.2 0.2
0.1
0.1
0.0
9.84 19.69 29.53 39.37 49.21 59.06
0 1,450 2,901 4,351 5,802
Surface Speed (fpm)
Pressure (psi)
60
Shaft Materials 50
The effect of the type of shaft material used with iglide ® UW plain 40
bearings at low loads is small, as shown in the graph below. However,
30
the graph to the right shows that the shaft material selection becomes
Wear (µm/km)
more significant at higher loads. 20
For more questions concerning a specific running surface, please
contact an igus® technical sales associate. 10
0
➤ Shaft Materials, Page 71 1050 Hard 304 Stainless HR Carbon
Steel Chromed Steel Steel
Oscillating Rotating
20
8.0 18
16
7.0
14
Hard anodized aluminum
6.0 12
Automatic screw steel
10
1050, hard chromed
5.0
8
HR Carbon Steel
Wear (µm/km)
4.0 6
304 Stainless
3.0 4
Wear (µm/km)
2
2.0 0
440B
1050
Chemical Resistance
1.0
weak acids, as well as to solvents and all types of lubricants. The 0.8
0.7
moisture absorption of iglide® UW plain bearings is approximately 0.2%
0.6
in standard atmosphere. The saturation in water is 0.8%. These values
0.5
are so low that considering expansion by moisture absorption is only
0.4
required under extreme conditions.
0.3
0.2
➤ Chemical table, Page 1364
0.1
0.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Moisture Absorption (%)
Medium Resistance
Alcohol + Effect of moisture absorption on iglide® UW plain
Hydrocarbon + bearings
Radiation Resistance
iglide® UW plain bearings are radiation resistant to a radiation intensity of 3 x 102 Gy.
UV-Resistance
iglide® UW plain bearings are resistant to the impact of UV radiation
Vacuum
Applications in a vacuum are only possible to a limited extent. Only dehumidified bearings of iglide® UW should be tested in a vacuum.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
UWSM-0304-05 3.0 4.5 5.0 3.014 3.054 4.500 4.512 2.975 3.000
UWSM-0405-06 4.0 5.5 6.0 4.020 4.068 5.500 5.512 3.970 4.000
UWSM-0507-08 5.0 7.0 8.0 5.020 5.068 7.000 7.015 4.970 5.000
UWSM-0608-08 6.0 8.0 8.0 6.020 6.068 8.000 8.015 5.970 6.000
UWSM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
UWSM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
UWSM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
UWSM-1618-12 16.0 18.0 12.0 16.032 16.102 18.000 18.018 15.957 16.000
UWSM-1820-15 18.0 20.0 15.0 18.032 18.102 20.000 20.021 17.957 18.000
30°
UW F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
UWFM-0304-05 3.0 4.5 7.5 5.0 0.75 3.014 3.054 4.500 4.512 2.975 3.000
UWFM-0405-06 4.0 5.5 9.5 6.0 0.75 4.020 4.068 5.500 5.512 3.970 4.000
UWFM-0507-05 5.0 7.0 11.0 5.0 1.0 5.020 5.068 7.000 7.015 4.970 5.000
UWFM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
UWFM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
UWFM-1012.10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
UWFM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
UWFM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
UWFM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
573
iglide®
N54 iglide® N54 - The biopolymer
Based on renewable resources
Self-lubricating and
maintenance-free Made of 54% renewable resources. The most environmentally
friendly of all iglide bearings.
Mechanical Properties
Modulus of elasticity psi 261,000 DIN 53457
Tensile strength at 68°F psi 10,150 DIN 53452
Compressive strength psi 4,351
Permissible static surface pressure (68°F) psi 8,700
Shore D-hardness 74 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
7
Compressive Strength 6
The compressive strength of iglide® N54 bearings decreases with 5
increasing temperatures. The graph clarifies this relationship. At the
4
long-term permitted application temperature of 176°F, the permitted
3
Deformation (%)
surface pressure is less than 1,450 psi. The graph shows the elastic
deformation of iglide® N54 at radial loads. 2
1
➤ Compressive strength, Page 63
0
0 2,176 4,351 5,802
Pressure (psi)
140°F 73°F
Deformation under load and temperature
Temperatures 5,802
Presure (psi)
when considering the temperature limits.
1,450
0.5 0.7
0.6
0.4
0.5
Coefficient of friction (µ)
0.4
0.3
0.3
0.2
0.2
0.1
0.0
0.1 0 1,450 2,901 4,351 5,802 7,252 8,702 10,150 11,600
9.84 19.69 29.53 39.37 49.21 59.06 Pressure (psi)
Surface speed (fpm)
Coefficients of friction of iglide® N54 as a function Coefficients of friction of iglide® N54 as a function of
of the running speed; p = 145 psi the load, v = 1.96 fpm
200
180
Shaft Materials 160
140
It is important to select a suitable shaft material. As a rule, iglide® N54 120
is better suited for hard or soft shafts, but hard shaft surfaces tend to 100
have better holding times. Starting at loads 145 psi, wear increases 80
Wear (µm/km)
measurably and continuously. 60
40
20
➤ Shaft Materials, Page 71
0
0 1,450 2,901 4,351
Pressure (psi)
Rotating Oscillating
24
10
20
9
8 16
Hard anodized aluminum
7 12
1050, hard chromed
Wear (µm/km)
8
HR Carbon Steel
5
Automatic steel
304 Stainless
4 4
Wear (µm/km)
3
0
2 0 72 145 217 290
440B
1050
1 Pressure (psi)
0 1050 Steel 304 Stainless
HR Carbon Steel Hard chromed
Wear of iglide N54, rotating applications with different
®
Chemical Resistance
1.4
iglide® N54 plain bearings have good resistance to chemicals. They 1.2
are resistant to most lubricants. iglide® N54 is not impaired by most
0.4
0.2
0.0
0 1 2 3 4 5 6 7 8
Radiation Resistance
iglide® N54 plain bearings can be used with restrictions when exposed to radiation. iglide® N54 plain bearings are radiation resistant to a radiation
intensity of 1 x 104 Gy.
UV-Resistance
iglide® N54 plain bearings are resistant to the impact of UV radiation.
Vacuum
Any absorbed water will be emitted as gas in a vacuum. Applications under vacuum conditions are possible with restrictions.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
N54SM-0608-06 6.0 8.0 6.0 6.020 6.068 8.000 8.015 5.970 6.000
N54SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
N54SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
N54SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
N54SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
N54SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
30°
N54 F M -06 08-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
N54FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
N54FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
N54FM-1012.10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
N54FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
N54FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
N54FM-2023-21 20.0 23.0 30.0 21.5 1.5 20.040 20.124 23.000 23.021 19.948 20.000
581
iglide®
G V0 iglide® G V0 - V0 rating according to UL94
Versatile and cost effective
UL94 V0 rating The material achieves the UL94 V0 rating and is therefore
ideally suited for applications with stringent fire protection
regulations (vehicle and aircraft interiors, building interior
systems, etc.). Other properties are similar to the general
purpose iglide® G300 material.
Mechanical Properties
Modulus of elasticity psi 1,146,000 DIN 53457
Tensile strength at 68°F psi 20,310 DIN 53452
Compressive strength psi 14,500
Permissible static surface pressure (68°F) psi 10,880
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
10
Compressive Strength 9
8
With increasing temperatures, the compressive strength of iglide G V0
®
7
plain bearings decreases. However, at the longterm maximum temperature 6
of +266 °F the permissible surface pressure is still around 5,076 psi. The 5
Deformation (%)
Temperatures 120
The ambient temperatures greatly influence the wear performance of plastic 100
bearings. The short term maximum temperature is +410 °F, this allows the 80
use of iglide® G V0 plain bearings in heat treating applications in which the
bearings are not subjected to additional loading. The ambient application 60
temperature has a direct impact on bearing wear, an increase in temperature
40
Pressure (psi)
results in an increase in wear. With increasing temperatures, the wear
increases and this effect is significant when temperatures rise over +248 °F. 20
At temperatures over +212 °F an additional securing is required.
0
➤ Application temperatures, Page 67 68 86 104 122 140 158 176 194 212 230 248 266
Temperature (°F)
0.5 0.35
0.30
0.4
0.25
Coefficient of friction (µ)
0.3
0.20
0.2 0.15
0.10
0.1
0.05
0.0 0.00
19.69 29.53 39.37 49.21 59.06 68.90 78.74 88.58 98.43
0 1,450 2,901 4,351 5,802 7,252 8,702 10,150 11,600
Surface speed (fpm) Pressure (psi)
Shaft Materials 9
8
The friction and wear are also dependent to a large degree
7
HR Carbon Steel
Automatic steel
recommended. The graph shows results of testing different shaft materials 4
304 Stainless
Wear (µm/km)
with plain bearings made from iglide® G V0. It is important to notice that 3
with increasing loads, the recommended hardness of the shaft increases. 2
440B
1050
The “soft” shafts tend to wear more easily and thus affect the clearance of 1
the overall system. If the loads exceed 290 psi it is important to recognize 0
that the wear rate (the gradient of the curves) clearly decreases with the
hard shaft materials. The comparison of rotational movements to oscillating Wear of iglide® G V0, rotating applications with different
movements shows that iglide® G V0 provides advantages in oscillating shaft materials, p = 108 psi, v = 98 fpm
movements at loads up to 4,351 psi. If the shaft material you plan to use
is not contained in this list, please contact us.
200
180
➤ Shaft Materials, Page 71 160
140
120
100
80
Wear (µm/km)
60
40
20
0
0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
Pressure (psi)
Rotating Oscillating
Moisture absorption
0.6
The moisture absorption of iglide® G V0 plain bearings is approximately
0.5
0.7 % in ambient conditions. The saturation limit submerged in water is 4 %.
0.3
0.2
0.1
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Moisture absorption (weight %)
Radiation Resistance
Plain bearings made from iglide® G V0 are resistant to radiation up to an intensity of 3 · 102 Gy.
UV-Resistance
iglide® G V0 plain bearings are permanently resistant to UV radiation.
Vacuum
iglide® G V0 plain bearings outgas in a vacuum. Use in vacuum is only possible with dehumidified bearings.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
GV0SM-0608-06 6.0 8.0 6.0 6.020 6.058 8.000 8.015 5.970 6.000
GV0SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
GV0SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
GV0SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
GV0SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
GV0SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
GV0SM-2528.20 25.0 28.0 20.0 25.040 25.124 28.000 28.021 24.948 25.000
GV0SM-3034-30 30.0 34.0 30.0 30.040 30.124 34.000 34.025 29.938 30.000
GV0SM-3539-40 35.0 39.0 40.0 35.050 35.150 39.000 39.025 34.938 35.000
GV0SM-4044-40 40.0 44.0 40.0 40.050 40.150 44.000 44.025 39.938 40.000
30°
G V0 F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
GV0FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
GV0FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
GV0FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
GV0FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
GV0FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
GV0FM-2023-21 20.0 23.0 30.0 21.0 1.5 20.040 20.124 23.000 23.021 19.948 20.000
GV0FM-2528-21 25.0 28.0 35.0 21.0 1.5 25.040 25.124 28.000 28.021 24.948 25.000
GV0FM-3034-37 30.0 34.0 42.0 37.0 2.0 30.040 30.124 34.000 34.025 29.948 30.000
GV0FM-3539-36 35.0 39.0 47.0 36.0 2.0 35.050 35.150 39.000 39.025 34.938 35.000
GV0FM-4044-40 40.0 44.0 52.0 40.0 2.0 40.050 40.150 44.000 44.025 39.938 40.000
589
iglide®
J2 iglide® J2 - Versatile and cost-effective
Environmentally friendly
Good mechanical
properties, robust iglide® J2 has good universal media resistance, comparable
to that of iglide® J and similar materials. The mechanical
specifications in sporadically moved applications are better
although, in comparison, clear compromises have to
be made with regard to friction and wear. Like all iglide®
materials, iglide® J2 is PFOA-free.
Economic
Good media resistance l When low moisture absorption and good chemical
resistance is required for primarily static load
l When a low-priced bearing is required for use in a wet
environment with low pv values
l When there is a basic lubrication of the bearing
Self-lubricating
and maintenance-free
Mechanical Properties
Modulus of elasticity psi 522,900 DIN 53457
Tensile strength at 68°F psi 14,650 DIN 53452
Compressive strength psi 11,170
Permissible static surface pressure (68°F) psi 6,672
Shore D-hardness ND DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
10
Compressive Strength 9
8
With increasing temperatures, the compressive strength of iglide J2 plain ®
7
bearings decreases. The recommended maximum surface pressure is a 6
mechanical material parameter. No conclusions regarding the tribological 5
Deformation (%)
properties can be drawn from this. The graph to the right shows the elastic 4
deformation of iglide® J2 under different loads. A possible deformation 3
2
could be, among others, dependant on the duty cycle of the load.
1
0
0 725 1,450 2,176 2,901 3,626 4,351 5,076 5,802 6,527
➤ Compressive strength, Page 63
Pressure (psi)
140°F 73°F
Temperatures 10,150
8,702
The ambient application temperature has a direct impact on bearing wear,
an increase in temperature results in an increase in wear. With increasing 7,252
temperatures, the wear increases and this effect is significant when 5,802
temperatures rise over +194°C. At temperatures over +140 °C an additional
4,351
securing is required.
Pressure (psi)
2,901
➤ Application temperatures, Page 67
1,450
0
68 86 104 122 140 158 176 194
Temperature (°F)
iglide® J2 Application Temperature Recommended maximum permissible static surface
Minimum -58°F pressure of iglide® J2 as a result of the temperature
0.25 0.30
0.25
0.20
Coefficient of friction (µ)
0.20
0.15
0.15
0.10
0.10
19.7 39.3 59.0 78.7 98.4 118.1 137.8 157.5 177.2 196.9 0 725 1,450 2,176 2,901 3,626 4,351 5,802
Surface speed (fpm) Pressure (psi)
Wear (µm/km)
delivers good wear values especially with cutting steel in rotation at 145 psi.
100
When running dry, the wear values are sometimes significantly higher on
50
other shafts. Unlike many other iglide® materials, the wear rate in pivoting
is slightly higher compared to the rate in rotation with otherwise identical 0
5 1,450 2,901 4,351 5,802
parameters.
Pressure (psi)
Rotating Oscillating
➤ Shaft Materials, Page 71
8.0
Hard anodized aluminum
6.0
1050, hard chromed
HR Carbon Steel
Automatic steel
4.0
304 Stainless
Wear (µm/km)
2.0
440B
1050
0.0
Moisture absorption
0.10
Radiation Resistance
Plain bearings made from iglide® J2 are resistant to radiation up to an intensity of applications 3 · 102 Gy.
UV-Resistance
iglide® J2 plain bearings become discoloured under UV radiation. However,
Vacuum
In vacuum applications, any absorbed moisture content is outgassed. Use in vacuum is only possible with dehumidified bearings.
Outer-Ø d2 (mm)
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
J2SM-0608-06 6.0 8.0 6.0 6.020 6.058 8.000 8.015 5.970 6.000
J2SM-0810-10 8.0 10.0 10.0 8.025 8.083 10.000 10.015 7.964 8.000
J2SM-1012-10 10.0 12.0 10.0 10.025 10.083 12.000 12.018 9.964 10.000
J2SM-1214-12 12.0 14.0 12.0 12.032 12.102 14.000 14.018 11.957 12.000
J2SM-1618-15 16.0 18.0 15.0 16.032 16.102 18.000 18.018 15.957 16.000
J2SM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
J2SM-2528.20 25.0 28.0 20.0 25.040 25.124 28.000 28.021 24.948 25.000
30°
J2 F M -04 05-04
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
iglide® material
Form F (flange)
r r = max. 0.5
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size
d13 h13 -0.14 Min. Max. Min. Max. Min. Max.
J2FM-0608-06 6.0 8.0 12.0 6.0 1.0 6.020 6.068 8.000 8.015 5.970 6.000
J2FM-0810-10 8.0 10.0 15.0 10.0 1.0 8.025 8.083 10.000 10.015 7.964 8.000
J2FM-1012-10 10.0 12.0 18.0 10.0 1.0 10.025 10.083 12.000 12.018 9.964 10.000
J2FM-1214-12 12.0 14.0 20.0 12.0 1.0 12.032 12.102 14.000 14.018 11.957 12.000
J2FM-1618-17 16.0 18.0 24.0 17.0 1.0 16.032 16.102 18.000 18.018 15.957 16.000
J2FM-2023-21 20.0 23.0 30.0 21.0 1.5 20.040 20.124 23.000 23.021 19.948 20.000
iglide® Q290
• Long life especially on soft shafts
• Resistant to edge loads
• Continuous use up to 284°F
• Good price/performance ratio
597
iglide®
Q290
iglide® Q290 - Heavy-duty on soft shafts
For moderate to high loads, especially on soft shafts
High service life, iglide ® Q290 shows outstanding service life in robust
especially on soft shafts pivoting applications, as they are frequently found in
some agricultural machinery, especially on “soft” coatings
(e.g. galvanized).
Continuous use
up to 284°F
Mechanical Properties
Modulus of elasticity psi 445,800 DIN 53457
Tensile strength at 68°F psi 14,070 DIN 53452
Compressive strength psi 9,863
Permissible static surface pressure (68°F) psi 7,977
Shore D-hardness 80 DIN 53505
Electrical Properties
Specific volume resistance Ωcm > 1010 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Compressive Strength 25
20
With increasing temperatures, the compressive strength of iglide® Q290
plain bearings decreases. With the short-term permitted application
15
temperature of +356 °F, the permitted surface pressure is still more than
Deformation (%)
Pressure (psi)
➤ Compressive strength, Page 63
Deformation under
+23load
°C and temperature
+60 °C
Temperatures
11,600
The maximum long-term application temperature of +284°F enables the
use of iglide® Q290 in, for example, typical applications in the agricultural, 10,150
Pressure (psi)
➤ Application temperatures, Page 67
2,901
1,450
0
iglide® Q290 Application Temperature 68 104 140 176 212 248 284
0.50 0.20
0.40
0.15
Coefficient of friction (µ)
Coefficient of friction (µ)
0.30
0.10
0.20
0.05
0.10
0.00 0.00
0 19.7 39.4 59.1 78.7 98.4 118.1 137.8 145 1,450 3,626 5,802 7,977
Surface speed (fpm) Pressure (psi)
Coefficient of friction as a result of the surface speed; Coefficient of friction as a result of the load, v = 1.97 fpm
load = 108 psi constant
1050, hard-chromed
Wear (µm/km)
4.0
1050
2.0
0.0
240
Failed*
2000
200
1750
160
1500
1250 120
Wear rate (µm/km)
1000
Wear (µm/km)
80
750
40
500
0
0 0 725 2,176 3,626 5,076 6,527 7,977
iglide Q290
®
iglide Z
®
Rolled metallic
bearing with Pressure (psi)
gliding layer Rotating Oscillating
Wear, pivoting applications on galvanized shafts, Wear for oscillating and rotating applications with a
p > 7,252 psi, v = 59 fpm 1050 hard chromed and ground steel as a function of
the pressure
Moisture absorption
Under normal climatic conditions, the moisture absorption of iglide® Q290
plain bearings is 3.0 Wt.-%. The saturation limit in water is 9.3 Wt.- %.
Radiation Resistance
Plain bearings made from iglide® Q290 are resistant to radiation up to an intensity of applications 3 · 102 Gy.
UV-Resistance
iglide® Q290 bearings have good resistance to UV rays and other weathering effects.
Vacuum
In a vacuum, any moisture content will outgas. Use in vacuum is only possible to a limited extent.
iglide® Q290
Electrical Properties Specific volume resistance > 1010 Ωcm
iglide Q290 plain bearings are electrically insulating.
®
Surface resistance > 1012 Ω
Outer-Ø d2 (mm)
b1
Inner-Ø d1 (mm)
f
Length b1 (mm)
Form S (sleeve)
iglide® material
0.5 mm
Metric
Dimensions according to ISO 3547-1 and special dimensions
*Based on steel housing bore
QSM-2023-20 20.0 23.0 20.0 20.040 20.124 23.000 23.021 19.948 20.000
QSM-2528-30 25.0 28.0 30.0 25.040 25.124 28.000 28.021 24.948 25.000
QSM-3034-30 30.0 34.0 30.0 30.040 30.124 34.000 34.025 29.948 30.000
QSM-3539-40 35.0 39.0 40.0 35.050 35.150 39.000 39.025 34.938 35.000
QSM-4044-40 40.0 44.0 40.0 40.050 40.150 44.000 44.025 39.938 40.000
QSM-5055-50 50.0 55.0 50.0 50.050 50.150 55.000 55.030 49.938 50.000
More products
...
...
...plastics
iglide® more products - Product overview
Clip bearings - Clip2 bearings - Clip2 bearings - Clip2 bearings - Clip2 bearings -
Easy to fit, securely Easy installation due Easy installation due With anti-rotation With anti-rotation
with the double flange to split design to split design feature feature
design Inch dimensions Metric dimensions Inch dimensions Metric dimensions
➤ Page 614 ➤ Page 616 ➤ Page 617 ➤ Page 618 ➤ Page 619
Preloaded iglide® J - Knife edge rollers - Flange bearings - Polymer disc springs -
Zero play and rattling For precise Secured by screws Cushion and
conveying dampen
➤ Page 650 ➤ Page 651 ➤ Page 652 ➤ Page 653 ➤ Page 656
robolink® D -
Motor-driven iglide® PRT
slewing ring bearings
➤ Page 657
• Easy to fit
• Good abrasion resistance
• Predictable service life
• Custom versions possible
609
iglide® Clip bearings - Advantages
Solutions for stamped sheet metal
Ø 3/16 to 1 inches
more dimensions on request
Custom solution
iglide® flanged bearings
Easy to fit
Pressfit
Axial load on both sides
Compensation of tolerances of the sheet metal
➤ Page 620
Custom solution
iglide® double flange bearing
Easy to fit due to clip-on feature
Large flange surfaces
Symmetrical flange
Remains in place during E-Coat paint process
➤ Page 621
Custom solution
iglide® snap On
The disc is snapped onto the flanged bearing with undercuts
Compensation of axial clearance
Pre-assembly possible
Combination of conductive and non-conductive
materials
➤ Page 622
This cutting mechanism is used in the beverage industry. All used Easy-to-clean and low-cost iglide® clip bearings and iglide® flange
components meet the requirement of freedom from lubrication with bearings are used in a honeycomb.
low weight and low cost.
By using wear-resistant iglide® clip bearings, the lowering The guide rod in this pharmacy printer has been attached using
mechanism for radiator mascots on luxury cars could be improved. igus® clip bearings.
Temperature limits
Mechanical properties
The permissible static pressure of iglide® M250 at room temperature is
2,901 psi. Due to the possibility of high tolerances in the housing bore, Installation
the clip bearing has a high compressive strength even for punched holes.
For bearing surfaces that are very small, the vibration dampening properties For installation, the plain bearings are pressed together on the side with
and the resistance to edge loads are especially important. the large flange. The angled slot makes the bearing spiral shaped so that
it can be placed easily into the metal plate.
➤ iglide® M250, Page 135 The slot also compensates for expansions of the circumference. In this way,
a tight clearance is possible with the clip bearings. The bearing clearance is
dimensioned in such a way that in a housing bore with a nominal diameter,
7,252 a shaft made with the same nominal diameter turns easily. The clip bearings
should be fitted into a housing with a “H” class tolerance, up to H13. The
5,802 clip bearing can also rotate within the housing bore.
4,351
2,901
Pressure (psi)
1,450
0
68 86 104 122 140 158 176
Temperature (°F)
b1
Order key
s s
Type Dimensions
M C I - 06 - 01
d1
d4
d2
d3
Inner-Ø d1 [mm]
iglide® material
Clip bearings
b1–2s [mm]
Material:
iglide® M250 ➤ Page 135
Length
Inch
Dimensions [mm]
Part Number d1 d2 d3 d4 s b1 ID of Bearing Recommended Recommended Recommended
D117)
–0.10 + 0.20 in Housing Sheet Metal Housing Bore Shaft Size
Thickness Max. Min. Max. Min.
MCI-03-01 3/16 0.2343 1/4 5/16 0.032 0.1380 .1885 .040/.075 0.2414 0.2343 0.1875 0.1865
MCI-03-02 3/16 0.2343 1/4 5/16 0.032 0.2000 .1885 .072/.135 0.2414 0.2343 0.1875 0.1865
MCI-04-01 1/4 0.3125 11/32 7/16 0.032 0.1380 .2510 .040/.075 0.3212 0.3125 0.2500 0.2490
MCI-04-02 1/4 0.3125 11/32 7/16 0.032 0.2000 .2510 .072/.135 0.3212 0.3125 0.2500 0.2490
MCI-05-01 5/16 0.3750 13/32 1/2 0.032 0.1380 .3135 .040/.075 0.3834 0.3750 0.3125 0.3115
MCI-05-02 5/16 0.3750 13/32 1/2 0.032 0.2000 .3135 .072/.135 0.3834 0.3750 0.3125 0.3115
MCI-06-01 3/8 0.4375 15/32 9/16 0.032 0.1380 .3760 .040/.075 0.4481 0.4375 0.3750 0.3740
MCI-06-02 3/8 0.4375 15/32 9/16 0.032 0.2000 .3760 .072/.135 0.4481 0.4375 0.3750 0.3740
MCI-07-01 7/16 0.5000 17/32 5/8 0.032 0.1380 .4385 .040/.075 0.5106 0.5000 0.4375 0.4365
MCI-07-02 7/16 0.5000 17/32 5/8 0.032 0.2000 .4385 .072/.135 0.5106 0.5000 0.4375 0.4365
MCI-08-01 1/2 0.5625 19/32 11/16 0.032 0.1380 .5010 .040/.075 0.5731 0.5625 0.5000 0.4990
MCI-08-02 1/2 0.5625 19/32 11/16 0.032 0.2000 .5010 .072/.135 0.5731 0.5625 0.5000 0.4990
MCI-08-03 1/2 0.5625 19/32 11/16 0.032 0.2480 .5010 .183/.120 0.5731 0.5625 0.5000 0.4990
MCI-10-01 5/8 0.6875 23/32 7/8 0.032 0.1380 .6260 .040/.075 0.6981 0.6875 0.6250 0.6240
MCI-10-02 5/8 0.6875 23/32 7/8 0.032 0.2000 .6260 .072/.135 0.6981 0.6875 0.6250 0.6240
MCI-12-01 3/4 0.8125 27/32 1 0.032 0.1380 .7510 .040/.075 0.8255 0.8125 0.7500 0.7490
MCI-12-02 3/4 0.8125 27/32 1 0.032 0.2000 .7510 .072/.135 0.8255 0.8125 0.7500 0.7490
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005). Please see D11 tolerances table ➤ Page 75
b1
Order key
s s
Type Dimensions
M C M - 06 - 015
d1
d4
d2
d3
Inner-Ø d1 [mm]
iglide® material
Clip bearings
b1–2s [mm]
Material:
Length
Metric
iglide® M250 ➤ Page 135
Dimensions [mm]
Part Number d1 d2 d3 d4 s b1 ID of Bearing Recommended Recommended Recommended
D117) –0.10 + 0.20 in Housing Sheet Metal Housing Bore Shaft Size
Thickness Max. Min. Max. Min.
MCM-03-02 3 4.2 4.8 6 0.6 3.2 3.025 2.34/1.45 4.380 4.200 3.000 2.975
MCM-03-03 3 4.2 4.8 6 0.6 4.2 3.025 3.13/2.87 4.380 4.200 3.000 2.975
MCM-04-02 4 5.2 5.9 7 0.6 3.2 4.025 2.34/1.45 5.380 5.200 4.000 3.975
MCM-04-03 4 5.2 5.9 7 0.6 4.2 4.025 3.13/2.87 5.380 5.200 4.000 3.975
MCM-05-02 5 6.2 6.8 8 0.6 3.2 5.025 2.34/1.45 6.420 6.200 5.000 4.975
MCM-05-03 5 6.2 6.8 8 0.6 4.2 5.025 3.13/2.87 6.420 6.200 5.000 4.975
MCM-06-015 5 6.2 6.8 8 0.6 4.2 6.025 2.34/1.45 7.420 7.200 6.000 5.975
MCM-06-02 6 7.2 7.8 11 0.6 3.2 6.025 2.34/1.45 7.420 7.200 6.000 5.975
MCM-06-03 6 7.2 7.8 11 0.6 4.2 6.025 3.13/2.87 7.420 7.200 6.000 5.975
MCM-06-04 6 7.2 7.8 11 0.6 5.2 6.025 4.40/4.00 7.420 7.200 6.000 5.975
MCM-07-03 7 9 9.8 13 0.8 4.6 7.025 3.13/2.87 9.220 9.000 7.000 6.975
MCM-08-02 8 9.6 10.4 13 0.8 3.6 8.025 2.34/1.45 9.820 9.600 8.000 7.975
MCM-08-03 8 9.6 10.4 13 0.8 4.6 8.025 3.13/2.87 9.820 9.600 8.000 7.975
MCM-08-04 8 9.6 13.0 10.4 0.8 5.6 8.025 3.13/2.87 9.820 9.600 8.000 7.975
MCM-09-02 9 10.6 11.4 14 0.8 3.6 9.025 2.34/1.45 10.870 10.600 9.000 8.975
MCM-10-02 10 11.6 12.4 15 0.8 3.6 10.025 2.34/1.45 11.870 11.600 10.000 9.975
MCM-10-025 10 11.6 12.4 15 0.8 4.1 10.025 2.34/1.45 11.870 11.600 10.000 9.975
MCM-10-03 10 11.6 12.4 15 0.8 4.6 10.025 3.13/2.87 11.870 11.600 10.000 9.975
MCM-10-08 10 11.6 12.4 15 0.8 9.6 10.025 3.13/2.87 11.870 11.600 10.000 9.975
MCM-12-02 12 13.6 14.4 17 0.8 3.6 12.025 2.34/1.45 13.870 13.600 12.000 11.975
MCM-12-025 12 13.6 14.4 17 0.8 4.4 12.025 2.34/1.45 13.870 13.600 12.000 11.975
MCM-12-03 12 13.6 14.4 17 0.8 4.6 12.025 3.13/2.87 13.870 13.600 12.000 11.975
MCM-12-035 12 13.6 14.4 17 0.8 5.1 12.025 3.13/2.87 13.870 13.600 12.000 11.975
MCM-12-04 12 13.6 14.4 17 0.8 5.6 12.025 4.40/4.00 13.870 13.600 12.000 11.975
MCM-14-03 14 15.6 16.4 19 0.8 4.6 14.025 3.13/2.87 15.870 15.600 14.000 13.975
MCM-16-02 16 17.6 18.4 21 0.8 3.6 16.025 2.34/1.45 17.870 17.600 16.000 15.975
MCM-16-03 16 17.6 18.4 21 0.8 4.6 16.025 3.13/2.87 17.870 17.600 16.000 15.975
MCM-18-02 18 20 21 21 0.8 4 18.025 3.13/2.87 20.330 20.000 18.000 17.975
MCM-18-03 18 20 21 23 1.0 5.0 18.025 3.13/2.87 20.330 20.000 18.000 17.975
MCM-20-03 20 22 23 25 1.0 5.0 20.025 3.13/2.87 22.330 22.000 20.000 19.975
MCM-25-03 25 27 28 30 1.0 5.0 25.025 3.13/2.87 27.330 27.000 25.000 24.975
MCM-25-06 25 27 28 30 1 8 25.025 3.13/2.87 27.330 27.000 25.000 24.975
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005). Please see D11 tolerances table ➤ Page 75
d1 Order key
d3 + 0.04 mm
30
M Y I - 04 - 04
°
b2 – 0.13 mm
0.5
b1
r = max. 0.5 mm
Inner-Ø d1 [inch]
d1
Length b1 [mm]
Based on 1/16”
Based on 1/16”
iglide® material
d3 + 0.04 mm d2
Form: Clips2
25°
Material:
30
°
iglide® M250 ➤ Page 135
Inch
with anti-rotation feature ➤ Page 618
b2 – 0.13 mm
0.5
b1
r = max. 0.5 mm
d2
Dimensions [mm]
Part d1 d2 d3 b1 b2 W Recommended Recommended
Number Housing Bore Shaft Size
Max. Min. Max. Min.
MYI-03-03 3/16 0.2339 5/16 3/16 0.0252 25° 0.2351 0.2339 0.1875 0.1865
MYI-04-04 1/4 0.2965 13/32 1/4 0.0252 25° 0.2979 0.2965 0.2500 0.2490
MYI-05-05 5/16 0.3744 1/2 5/16 0.0299 25° 0.3758 0.3744 0.3125 0.3115
MYI-06-06 3/8 0.4370 19/32 3/8 0.0299 25° 0.4387 0.4370 0.3750 0.3740
MYI-07-07 7/16 0.4996 21/32 7/16 0.0299 25° 0.5013 0.4996 0.4375 0.4365
MYI-08-06 1/2 0.5618 3/4 3/8 0.0299 25° 0.5635 0.5618 0.5000 0.4990
MYI-08-08 1/2 0.5618 3/4 1/2 0.0299 25° 0.5635 0.5618 0.5000 0.4990
MYI-10-07 5/8 0.6870 15/16 7/16 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-10-10 5/8 0.6870 15/16 5/8 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-10-18 5/8 0.6870 15/16 1 1/8 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-12-12 3/4 0.8118 1 1/8 3/4 0.0299 25° 0.8139 0.8118 0.7500 0.7490
MYI-12-18 3/4 0.8118 1 1/8 1 1/8 0.0299 25° 0.8139 0.8118 0.7500 0.7490
MYI-14-7.5 7/8 0.9370 1 5/16 15/32 0.0299 25° 0.9391 0.9370 0.8750 0.8740
MYI-14-14 7/8 0.9370 1 5/16 7/8 0.0299 25° 0.9391 0.9370 0.8750 0.8740
MYI-16-10 1 1.0933 1 1/2 5/8 0.0449 25° 1.0954 1.0933 1.0000 0.9985
MYI-16-14 1 1.0933 1 1/2 7/8 0.0449 25° 1.0954 1.0933 1.0000 0.9985
MYI-16-16 1 1.0933 1 1/2 1 0.0449 25° 1.0954 1.0933 1.0000 0.9985
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005)
9)
Recommended housing bore tolerance: H9
d1 Order key
d3 + 0.04 mm
30
M Y M - 04 - 04
°
b2 – 0.13 mm
0.5
b1
r = max. 0.5 mm
d1
Inner-Ø d1 [mm]
iglide® material
d3 + 0.04 mm d2
Form: Clips2
b1–2s [mm]
25°
Material:
30
Length
Metric
°
iglide® M250 ➤ Page 135
with anti-rotation feature ➤ Page 619
b2 – 0.13 mm
0.5
b1
r = max. 0.5 mm
d2
Dimensions [mm]
Part d1 d2 d3 b1 b2 W Recommended Recommended
Number Housing Bore Shaft Size
Max. Min. Max. Min.
MYM-04-04 4 5.2 7.0 4.0 0.6 25° 5.230 5.200 4.000 3.975
MYM-05-05 5 6.2 8.0 5.0 0.6 25° 6.236 6.200 5.000 4.975
MYM-06-06 6 7.2 9.5 6.0 0.6 25° 7.236 7.200 6.000 5.975
MYM-08-08 8 9.6 12.0 8.0 0.8 25° 9.636 9.600 8.000 7.975
MYM-10-10 10 11.6 15.0 10.0 0.8 25° 11.643 11.600 10.000 9.975
MYM-12-06 12 13.6 18.0 6.0 0.8 25° 13.643 13.600 12.000 11.975
MYM-12-12 12 13.6 18.0 12.0 0.8 25° 13.643 13.600 12.000 11.975
MYM-14-14 14 15.6 21.0 14.0 0.8 25° 15.643 15.600 14.000 13.975
MYM-16-16 16 17.6 24.0 16.0 0.8 25° 17.643 17.600 16.000 15.975
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005)
9)
Recommended housing bore tolerance: H9
d3 b1
d2 d2 Order key
b2
b1
5° 25°
max. 2 ma x.
Type Dimensions Option
ma x.
M Y I - 04 - 04 K
0.5
b2
25°
d1
d2
0.5
b1
b1
d1 30° k
Inner-Ø d1 [inch]
30°
Length b1 [mm]
Based on 1/16”
Based on 1/16”
iglide® material
Form: Clips2
Anti rotation
0.5
b2
0.5
b2
d1 30° d1 30°
feature
d3
Inch
k
Material:
k k
iglide® M250 ➤ Page 135
d3
d3
Dimensions [mm]
k k k k
Part d1 d2 d3 b1 b2 W Recommended Recommended
Number Housing Bore Shaft Size
Max. Min. Max. Min.
MYI-03-03K 3/16 0.2339 5/16 3/16 0.0252 25° 0.2351 0.2339 0.1875 0.1865
MYI-04-04K 1/4 0.2965 13/32 1/4 0.0252 25° 0.2979 0.2965 0.2500 0.2490
MYI-05-05K 5/16 0.3744 1/2 5/16 0.0299 25° 0.3758 0.3744 0.3125 0.3115
MYI-06-06K 3/8 0.4370 19/32 3/8 0.0299 25° 0.4387 0.4370 0.3750 0.3740
MYI-07-07K 7/16 0.4996 21/32 7/16 0.0299 25° 0.5013 0.4996 0.4375 0.4365
MYI-08-06K 1/2 0.5618 3/4 3/8 0.0299 25° 0.5635 0.5618 0.5000 0.4990
MYI-08-08K 1/2 0.5618 3/4 1/2 0.0299 25° 0.5635 0.5618 0.5000 0.4990
MYI-10-07K 5/8 0.6870 15/16 7/16 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-10-10K 5/8 0.6870 15/16 5/8 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-10-18K 5/8 0.6870 15/16 1 1/8 0.0299 25° 0.6887 0.6870 0.6250 0.6240
MYI-12-12K 3/4 0.8118 1 1/8 3/4 0.0299 25° 0.8139 0.8118 0.7500 0.7490
MYI-12-18K 3/4 0.8118 1 1/8 1 1/8 0.0299 25° 0.8139 0.8118 0.7500 0.7490
MYI-14-7.5K 7/8 0.9370 1 5/16 15/32 0.0299 25° 0.9391 0.9370 0.8750 0.8740
MYI-14-14K 7/8 0.9370 1 5/16 7/8 0.0299 25° 0.9391 0.9370 0.8750 0.8740
MYI-16-10K 1 1.0933 1 1/2 5/8 0.0449 25° 1.0954 1.0933 1.0000 0.9985
MYI-16-14K 1 1.0933 1 1/2 7/8 0.0449 25° 1.0954 1.0933 1.0000 0.9985
MYI-16-16K 1 1.0933 1 1/2 1 0.0449 25° 1.0954 1.0933 1.0000 0.9985
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005)
9)
Recommended housing bore tolerance: H9
d3 b1
d2 d2 Order key
b2
b1
5° 25°
max. 2 ma x.
Type Dimensions Option
ma x.
M Y M - 04 - 04 K
0.5
b2
25°
d1
d2
0.5
b1
b1
d1 30°
k
Inner-Ø d1 [mm]
30°
Length b1 [mm]
iglide® material
Form: Clips2
Anti rotation
0.5
b2
0.5
b2
d1 30° d1 30°
feature
Metric
d3
Material:
k k
iglide® M250 ➤ Page 135
d3
d3
Dimensions [mm]
k k k k
Part d1 d2 d3 b1 b2 W Recommended Recommended
Number Housing Bore Shaft Size
Max. Min. Max. Min.
MYM-04-04K 4 5.2 7.0 4.0 0.6 25° 5.230 5.200 4.000 3.975
MYM-05-05K 5 6.2 8.0 5.0 0.6 25° 6.236 6.200 5.000 4.975
MYM-06-06K 6 7.2 9.5 6.0 0.6 25° 7.236 7.200 6.000 5.975
MYM-08-08K 8 9.6 12.0 8.0 0.8 25° 9.636 9.600 8.000 7.975
MYM-10-10K 10 11.6 15.0 10.0 0.8 25° 11.643 11.600 10.000 9.975
MYM-12-06K 12 13.6 18.0 6.0 0.8 25° 13.643 13.600 12.000 11.975
MYM-12-12K 12 13.6 18.0 12.0 0.8 25° 13.643 13.600 12.000 11.975
MYM-14-14K 14 15.6 21.0 14.0 0.8 25° 15.643 15.600 14.000 13.975
MYM-16-16K 16 17.6 24.0 16.0 0.8 25° 17.643 17.600 16.000 15.975
7)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005)
9)
Recommended housing bore tolerance: H9
b3
Order key
Type Dimensions
s
M K M - 10 12 - 10
d1
d3
d2
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
iglide® material
Type (Form K)
Material:
iglide® M250 ➤ Page 135
Metric
Sample dimension [mm]
Part No. d1 d1 Tolerance d2 d3 b1 b2 b3 s
E10 d13 h13 –0.14 +0.1/+0.7 ±0.1
MKM-1012-10 10 +0.025 +0.083 12 18 14 1 10 0.4
3)
After pressfit. Testing methods ➤ Page 76
Assembly:
Order key
b1
s
Type Dimensions
M D M - 12 13 - 06
d1
d2
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
iglide® material
Type (Form D)
Material:
iglide® M250 ➤ Page 135
Metric
Sample dimension [mm]
Part No. d1 d1 Tolerance8) d2 d3 b1 s
MDM-1213-06 12 +0.050 +0.160 13 16.5 7 0.5
8)
d1 value is measured with a plug gauge after fitting into a reference housing d2 (+0.005)
Assembly:
Material:
iglide® M250 ➤ Page 135
Assembly:
The disc is snap on to the flange bushing with undercuts.
• Easy installation
• Economic
• More wear resistant than PTFE-strips
• High load capacity
• Standard range from stock
623
iglide® Piston rings - Advantages
Easy and economic: iglide® piston rings
More wear-resistant
than PTFE-strip
When to use it?
l When piston rings with excellent wear properties are
High load required
capacity
l When simple assembly is of great importance
l When high edge loads occur
Wear-resistant and l When tailor-made solutions based on iglide® materials
maintenance-free are required
1 2 3
More Information about iglide® material
and technical data iglide® J ➤ Page 115
max. +194°F
F
min. –58°F
4 5 Ø 6–70 mm
mm more dimensions on request
1 2
Type Dimensions
J PR M - 10 12 -054
b2
T
d2
iglide® material
d1
Outer Ø [mm]
Inner-Ø [mm]
Length [mm]
Piston ring
Metric
b1
dG
dG R max. 0.1
dS bG
bG R max. 0.1
Dimensions [mm]
Part No. d1 d2 b1 b2 T Part No. d1 d2 b1 b2 T
h13 ±0.5 [°] h13 ±0.5 [°]
JPRM-0608-06 6 8 6 1.0 0 JPRM-4550-10 45 50 10 2.0 0
JPRM-0810-10 8 10 10 1.0 0 JPRM-5055-054 50 55 5.4 2.5 20
JPRM-1012-054 10 12 5.4 2.5 20 JPRM-5055-10 50 55 10 2.0 0
JPRM-1214-054 12 14 5.4 2.5 20 JPRM-5863-095 58 63 9.5 (-0.22) 2.5 25
JPRM-1416-054 14 16 5.4 2.5 20 JPRM-6065-054 60 65 5.4 2.5 20
JPRM-1416-10 14 16 10 1.0 20 JPRM-7075-054 70 75 5.4 2.5 20
JPRM-1618-054 16 18 5.4 2.5 20
JPRM-1722-054 17 22 5.4 2.5 25
JPRM-2023-054 20 23 5.4 2.5 20
JPRM-2528-054 25 28 5.4 2.5 20
JPRM-2832-10 28 32 10 1.0 20
JPRM-2832-20 28 32 20 1.0 20
JPRM-2833-054 28 33 5.4 2.5 25
JPRM-3034-054 30 34 5.4 2.5 20
JPRM-3539-054 35 39 5.4 2.5 20
JPRM-3540-054 35 40 5.4 2.5 25
JPRM-4044-054 40 44 5.4 2.5 20
JPRM-4550-054 45 50 5.4 2.5 20
In addition to the stock range of iglide® J piston rings, you can also select your desired piston ring
on the basis of the entire iglide® bearing range. Order key
Use the entire iglide® bearing range and choose the material best suited to your application. Your
piston ring will be delivered within 10 days – to your requirements.
Type Dimensions
£ PR M - 06 08 - 06
Outer Ø [mm]
Inner Ø [mm]
Piston ring
b1
Required
Required
Metric
R max. 0.2 R max. 0.2
dH
dG
R max. 0.1
dG
dS
bG R max. 0.1 bG
Our material recommendations for special iglide® piston rings product finder
Material selection and individual dimensions made easy.
requirements:
With just a few clicks, the piston ring finder can find the optimum
iglide® A180: FDA-compliant ➤ Page 423 iglide® material and select the appropriate dimensions from the
iglide® J350: > +356 °F ➤ Page 279 standard catalogue range in order to define a piston ring in a
iglide® H1: Temperature up to +392 °F customized width.
➤ Page 377
• Maintenance-free
• Predictable service life
627
iglide® JV - Advantages
Zero-clearance and rattle free – preloaded iglide® J bearings
max. +194°F
F
min. –58°F
Material:
iglide® J ➤ Page 115
2 types
mm
Ø 6–20 mm
more dimensions on request
Ø 3/8 to 1 inches
Type Dimensions
b1
b3
J V S I - 06 08 - 06
60° d1
6x d2
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
Length b1 [mm]
iglide® material
pre-tensioned
b1
b3
Sleeve
Metric
d1
d2
Dimensions [mm]
Part No. d1 d2 b1 b3 f d1-Tolerance (E10)
h13 Max. Min.
JVSI-0608-06 3/8 1/2 3/8 0.079 0.3773 0.3750 6.020
JVSI-0810-08 1/2 5/8 1/2 0.079 0.5040 0.5013 8.025
JVSI-1012-10 5/8 3/4 5/8 0.098 0.6297 0.6270 10.025
JVSI-1214-12 3/4 7/8 3/4 0.098 0.7541 0.7505 12.032
JVSI-1618-16 1 1 1/8 1 0.098 1.0041 1.0007 14.032
14)
d1 – Measured after pressfit in housing bore. d2 H7 within the measurement plane
r Order key
Type Dimensions
d3
d1
d2
s J V F I - 06 08 - 06
r = max. 0.5 mm b2 b3
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
Length b1 [mm]
b1
iglide® material
pre-tensioned
Metric
Type
Dimensions [mm]
Part Number d1 d2 d3 b1 b2 b3 d1 Tolerance
Max. Min.
JVFI-0608-06 3/8 1/2 0.625 3/8 0.062 0.079 0.3773 0.3750
JVFI-0810-08 1/2 5/8 0.875 1/2 0.062 0.079 0.5040 0.5013
JVFI-1012-10 5/8 3/4 1.000 5/8 0.062 0.098 0.6297 0.6270
JVFI-1214-12 3/4 7/8 1.125 3/4 0.062 0.098 0.7541 0.7505
JVFI-1618-16 1 1 1/8 1.375 1 0.062 0.098 1.0041 1.0007
Type Dimensions
b1
b3
J V S M - 06 08 - 06
60° d1
6x d2
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
Length b1 [mm]
iglide® material
pre-tensioned
b1
b3
Metric
Type
d1
d2
Dimensions [mm]
Part No. d1 d2 b1 b3 f d1-Tolerance (E10)
h13 Max. Min.
JVSM-0608-06 6 8 6 2.0 1 6.068 6.020
JVSM-0810-08 8 10 8 2.0 1 8.083 8.025
JVSM-1012-10 10 12 10 2.0 1 10.083 10.025
JVSM-1214-12 12 14 12 2.0 1 12.102 12.032
JVSM-1416-14 14 16 14 2.0 1 14.102 14.032
JVSM-1517-15 15 17 15 2.5 1 15.102 15.032
JVSM-1820-18 18 20 18 2.5 1 18.102 18.032
JVSM-2023-20 20 23 20 2.5 1 20.140 20.040
14)
d1 – Measured after pressfit in housing bore. d2 H7 within the measurement plane
r
Order key
Type Dimensions
d3
d1
d2
s
J V F M - 06 08 - 06
b2 b3
r = max. 0.5 mm
b1
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
Length b1 [mm]
iglide® material
pre-tensioned
Metric
Type
Dimensions [mm]
Part No. d1 d2 d3 b1 b2 b3 s d1-Tolerance (E10)
h13 Max. Min.
JVFM-0810-10 8 10 15 10 1 2.0 0.44 8.083 8.025
JVFM-1012-10 10 12 18 10 1 2.0 0.53 10.083 10.025
JVFM-1214-12 12 14 20 12 1 2.0 0.53 12.102 12.032
JVFM-1416-12 14 16 22 12 1 2.0 0.53 14.102 14.032
JVFM-1517-15 15 17 23 15 1 2.5 0.53 15.102 15.032
JVFM-1820-11 18 20 26 11 1 2.5 0.53 18.102 18.032
JVFM-1820-18 18 20 26 18 1 2.5 0.53 18.102 18.032
JVFM-2023-20 20 23 30 20 1.5 2.5 0.62 20.140 20.040
14)
d1 – Measured after pressfit in housing bore. d2 H7 within the measurement plane
• 100% self-lubricating
• Low coefficient of friction
• Tight deflection radii
• Long service life of the belt
• Economic
• Long service life
633
iglide® Knife edge rollers - Advantages
Self-lubricating and precise deflection of conveyor belts
Depending on material:
F
iglide® A180: –58°F up to +194°F
iglide® A350: –148°F up to +356°F
iglide® P210: –40°F up to +266°F
3 Materials
mm Ø 3–10 mm ID, 9-20 mm OD
more dimensions on request
3.5
3.30
3.0
2.5 2.39
2.0
1.5
wear-rate [µm/km]
1.0 0.94
0.53
0.5 0.43
0.31
0.12 0.09 0.24 0.24
0
P210 A180 A350 PET-P POM-C
general purpose FDA-compliant traditional basic materials
Order key
Type Dimensions
A180 RL M - 03 09 - 50
d1
d2 b1
Outer-Ø d2 [mm]
Inner-Ø d1 [mm]
Length b1 [mm]
Options:
iglide® material
iglide® material
A180 = iglide® A180
Metric
Roller
d1
A350 = iglide® A350
d2 P210 = iglide® P210 b1
Knife edge rollers made from iglide® A180 – FDA compliant, up to 194°F
Part No. d1 +0.1 [mm] d2 ±0.1 [mm] b1 –0.3 [mm]
A180RLM-0309-50 3.1 9.0 50.0
A180RLM-0409-50 4.1 9.0 50.0
A180RLM-0511-70 5.1 11.0 70.0
A180RLM-0514-70 5.1 14.0 70.0
A180RLM-0612-70 6.1 12.0 70.0
A180RLM-0614-70 6.1 14.0 70.0
A180RLM-0812-70 8.1 12.0 70.0
A180RLM-0814-70 8.1 14.0 70.0
A180RLM-0818-70 8.1 18.0 70.0
A180RLM-1020-70 10.1 20.0 70.0
Knife edge rollers made from iglide® A350 – FDA compliant, up to 356 °F
Part No. d1 +0.1 [mm] d2 ±0.1 [mm] b1 –0.3 [mm]
A350RLM-0309-50 3.1 9.0 50.0
A350RLM-0614-70 6.1 14.0 70.0
A350RLM-0818-70 8.1 18.0 70.0
637
iglide® Flange bearings - Advantages
Maintenance free dry running
iglide® maintenance-free
iglide® G300:
Standard material for
flange bearings
many applications
With this design it is possible to use iglide® high performance
plain bearings in locations where recommended housing
bore tolerances are not possible. Due to the design of the
bearing, high loads are possible although there is a minimal
precision requirement of the housing.
iglide® T500 (X)*:
Material for high
Very good wear resistance
temperature applications
Low weight
Self-lubricating
Installation
For low radial loads, it is sufficient to mount iglide® flange
bearings on one surface simply with two bolts. For higher
iglide® J:
radial loads, it advisable to support the iglide® flange bearing
Material for low wear
in a hole. For this hole, large tolerances are permitted,
since it serves only as additional support for the iglide®
flange bearing. In order to achieve higher radial loads in
the bearings, the iglide® flange bearing can be pressfit into
a recommended housing bore with H7 tolerances. The
iglide® A180:
additional bolts ensure the fit of the bearing in the housing.
Material for use in
the food sector
Depending on material:
F
iglide® G300: –40°F up to +266°F
iglide® A180: –58°F up to +194°F
iglide® J: –58°F up to +194°F
iglide® T500 (X): –148°F up to +482°F
Material properties:
iglide® G300 ➤ Page 83
iglide® A180 ➤ Page 423
iglide J
®
➤ Page 115
iglide® T500 (X)* ➤ Page 193
4 materials
mm Ø 10–35 mm
more dimensions on request
*European part numbers for the high temperature material Available from stock
begin with X. Example XFL-... Detailed information about delivery time online.
b1
Flange bearings
b2
d4
b3
d7
d3
d6
Order key
b1
R
Type Size
b2
d4
b3
d5
d7
d3 G FL - 10
d6
Flange bearings
d1 Options:
iglide® material
Inner-Ø [mm]
d2 iglide® material
R
G = iglide® G300
d5
A180 = iglide® A180
J = iglide® J
T = iglide® T500 (X)
d1
Dimensions [mm] d2
Part No. d1 d1-Tolerance3) d213) d3 d4 d5 d6 d7 b1 b2 b3 R
(±0.2)
GFL-10 10 +0.025 +0.083 12 30 14 15 4.5 22 6 2 1 4
GFL-12 12 +0.032 +0.102 14 36 16 18 4.5 26 6 2 1 4.5
GFL-14 14 +0.032 +0.102 16 42 18 21 5.5 30 6 2 1 5
GFL-16 16 +0.032 +0.102 18 48 20 24 5.5 34 6 2 1 5.5
GFL-18 18 +0.032 +0.102 20 54 22 27 6.5 39 6 2 1 7
GFL-20 20 +0.040 +0.124 23 60 26 30 6.5 44 10 3 2 7
GFL-25 25 +0.040 +0.124 28 75 30 35 6.5 55 10 3 2 8.5
GFL-30 30 +0.040 +0.124 34 90 36 40 8.5 66 10 3 2 10
GFL-35 35 +0.050 +0.150 39 95 41 55 8.5 77 10 3 2 12
A180FL-10 10 +0.025 +0.083 12 30 14 15 4.5 22 6 2 1 4
A180FL-12 12 +0.032 +0.102 14 36 16 18 4.5 26 6 2 1 4.5
A180FL-16 16 +0.032 +0.102 18 48 20 24 5.5 34 6 2 1 5.5
A180FL-20 20 +0.040 +0.124 23 60 26 30 6.5 44 10 3 2 7
A180FL-25 25 +0.040 +0.124 28 75 30 35 6.5 55 10 3 2 8.5
A180FL-30 30 +0.040 +0.124 34 90 36 40 8.5 66 10 3 2 10
A180FL-35 35 +0.050 +0.150 39 95 41 55 8.5 77 10 3 2 12
JFL-10 10 +0.025 +0.083 12 30 14 15 4.5 22 6 2 1 4
JFL-12 12 +0.032 +0.102 14 36 16 18 4.5 26 6 2 1 4.5
JFL-14 14 +0.032 +0.102 16 42 18 21 5.5 30 6 2 1 5
JFL-16 16 +0.032 +0.102 18 48 20 24 5.5 34 6 2 1 5.5
JFL-20 20 +0.040 +0.124 23 60 26 30 6.5 44 10 3 2 7
JFL-25 25 +0.040 +0.124 28 75 30 35 6.5 55 10 3 2 8.5
JFL-30 30 +0.040 +0.124 34 90 36 40 8.5 66 10 3 2 10
JFL-35 35 +0.050 +0.150 39 95 41 55 8.5 77 10 3 2 12
TFL-10 10 +0.013 +0.071 12 30 14 15 4.5 22 6 2 1 4
TFL-12 12 +0.016 +0.086 14 36 16 18 4.5 26 6 2 1 4.5
TFL-14 14 +0.016 +0.086 16 42 18 21 5.5 30 6 2 1 5
TFL-16 16 +0.016 +0.086 18 48 20 24 5.5 34 6 2 1 5.5
TFL-20 20 +0.020 +0.104 23 60 26 30 6.5 44 10 3 2 7
TFL-25 25 +0.020 +0.104 28 75 30 35 6.5 55 10 3 2 8.5
TFL-30 30 +0.020 +0.104 34 90 36 40 8.5 66 10 3 2 10
TFL-35 35 +0.025 +0.125 39 95 41 55 8.5 77 10 3 2 12
3)
after pressfit. Testing methods ➤ Page 76 13)
pressfit in H7 tolerance housing bore
Polysorb -
iglide® J: Standard material
a wide range of applications
plastic disc springs
Spring washers are axially concave discs, meant to be
axially loaded for compensation of axial clearances and
Offers compensation of axial
manufacturing tolerances. Polysorb disc springs require
clearance and manufacturing
tolerances less space than other spring options, and are especially
suitable for applications that do not require a high spring
length.
Vibration dampening
When to use it?
When an application requires spring characteristics
typically only possible with metal at a considerable price
For compensation of axial clearances and
manufacturing tolerances
For vibration dampening
iglide® A500:
For noise reduction
high temperature material
When a non-magnetic material is required
For electrical and thermal insulation
Lightweight
When not to use it?
When constant spring forces are necessary over a wide
temperature range
When high spring forces are required
Depending on material:
F
iglide® J: –58°F up to +194°F
iglide® A500: –148°F up to +482°F
Material properties:
iglide® J ➤ Page 115
iglide® A500 ➤ Page 459
2 materials
mm Ø 5–20 mm
more dimensions on request
3.372 Table 02: Spring force [N] as a function of the absorbed moisture
Spring force [N]
2.248
1.124
Increased temperatures
0 Increased temperatures reduce the rigidity of plastic materials. Polysorb
0 20 40 60 80 100 disc springs made of standard iglide® J maintain a maximum spring
force of 1.8 lbs at the maximum permissible temperature of 194°F.
Deflection [%]
Compare spring force with ambient temperature in diagram 02.
JTEM-10 A500TEM-10
20
Chemical resistance
15
Polysorb disc springs are resistant to a variety of chemicals. For higher
resistance, iglide® A500 material discs should be used. 10
5
Medium Resistance
iglide® J iglide® A500 0
0 68 104 140 176 212 248 284 320 356 392 428
Alcohols + +
Ambient temperature [°F]
Hydrocarbons + +
Greases, oils without additives + + JTEM A500TEM
Fuels + + Diagram 02: Effect of ambient temperature on the spring force
Diluted acids 0 to – +
Strong acids – +
Diluted alkalines + +
Strong alkalines + to 0 +
+ resistant 0 conditionally resistant – not resistant
All data given at room temperature [+68°F]
Table 01: Chemical resistance
Order key
Type Dimensions
T E M- 05
iglide® J iglide® A500
Inner-Ø d1 [mm]
"Elastic spring"
iglide® material
d1
Metric
h0
t
Material options:
D iglide® J for low wear
iglide® A500 for FDA-compliant high
Material: temperature applications
Dimensions based on DIN 2093
iglide® J ➤ Page 115
iglide® A500 ➤ Page 459
Dimensions [mm]
Part No.15) Standard values: spring lengths and forces
D d1 t h0 F1.0 iglide® J F1.0 iglide® A500
[N] [N]
• Completely maintenance-free
• Easy installation and replaceable sliding pads
• High wear resistance
• For high load capacity, high rigidity
• Stainless steel versions available
• Wide range of accessories
645
iglide® PRT - Advantages
Maintenance free slewing ring bearing
iglide® PRT-01-60 is used here in a handling/transport system for A light and self-lubricating iglide® PRT slewing ring bearing is used
semiconductor carriers. Through a cylinder control, the PRT plastic in a self-rotating light, as found in discos for example.
slewing ring bearing provides a deflection at the end of the system’s
track.
In this machine tool control panel, an iglide® plastic slewing ring The iglide® PRT-01-100 slewing ring bearing is used in an automatic
bearing is used due to its freedom from external lubrication and welding plant in this application. It enables pivoting in the horizontal
maintenance. plane of the clamping device.
The self-lubricating iglide® PRT slewing ring bearing masters this Self-lubriating and maintenance-free plastic slewing ring bearings
job brilliantly, is lighter and in terms of purchasing is cheaper than a for moving the control panel. The low coefficients of friction ensure
comparable metal rotary connector. low actuating force during pivoting.
Type 01
Properties Unit -20 -30 -50 -60 -100 -150 -200 -300
Weight kg 0.2 0.4 1.0 1.1 1.3 2.2 3.2 7.6
Axial load, static N 15,000 27,000 40,000 50,000 55,000 80,000 100,000 150,000
Axial load, dynamic N 4,000 7,000 10,000 15,000 16,000 25,000 30,000 90,000
Radial load, static N 2,300 5,000 8,000 10,000 16,000 25,000 35,000 45,000
Radial load, dynamic N 600 1,500 2,500 3,000 5,000 8,000 10,000 27,000
Rotat. speed dry running 1/min 300 250 200 200 150 100 80 50
Max. perm. tilting moment Nm 100 200 600 800 1,500 2,000 3,800 5,000
Type 02
Properties Unit -20-AL /-20-ES -20-LC -20-P -30 -50 -60
Weight kg 0.1 0.1 72 0.2 0.44 0.7
Axial load, static N 13,000 13,000 13000 25,000 35,000 45,000
Axial load, dynamic N 4,000 4,000 4000 7,000 4,000 12,000
Radial load, static N 2,000 2,000 2000 2,500 5,000 10,000
Radial load, dynamic N 500 500 500 700 1,200 2,800
Rotat. speed dry running 1/min 250 250 250 200 120 120
Max. perm. tilting moment Nm 60 40 40 100 120 200
➤ www.igus.com/prt
2000
1500 100
50
2
1000
100
600 Diagram 01: Required drive torque versus
100 moment
applied
500
0 5000 10,000 20,000 30,000 50,000 70,000 90,000
400 Load [N] 50
PRT-01-20 PRT-01-30 PRT-01-60
300 2
600 PRT-01-100 PRT-01-150 PRT-01-200 PRT-01-300
Drive torque [Nm]
200 100
500 0 100
100
400 50
0
300 2
0 1000 2000 3000 4000 5000
200
PRT-01-20 PRT-01-30 PRT-01-60 0 100
100
PRT-01-100 PRT-01-150 PRT-01-200 PRT-01-300 Diagram 02: Required drive torque versus
0
applied moment
0 1000 2000 3000 4000 5000
Moment [Nm]
PRT-01-20 PRT-01-30 PRT-01-60
0.3 PRT-01-100 PRT-01-150 PRT-01-200 PRT-01-300
Deflection [°]
0.05
0.2
0.01
0.3
0.1 0.05
0 100 500
PRT-01-20
0 PRT-01-100
PRT-01-30 PRT-01-150
PRT-01-50 PRT-01-200
PRT-01-60 PRT-01-300
PRT-01-100 PRT-01-150 PRT-01-200 PRT-01-300
M4, min. M4, min. M6, min. M5, min. M5, min. M5, min. M6, min. M8, min.
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
6 screws 8 screws 12 screws 10 screws 12 screws 12 screws 12 screws 12 screws
2000
PRT-01-20 PRT-01-30 PRT-01-60
1500
All loadPRT-01-100
values assumePRT-01-150
the PRT is assembled with
socketPRT-01-300
PRT-01-200 100
head screws (strength class 8.8) on the outside pitch
50
circle diameter. For the assembly (using strength class 8.8 screws) of the PRT,2the screws have to be inserted to
1000
a minimum thread depth of 2 x d in every hole location in the outer ring. All data can be used for both lateral and
2000
500 horizontal assembly (including overhead installation). 0 1000 5000
1500 100
100 50
2
1000
0 5000 10,000 20,000 30,000 50,000 70,000 90,000
Order key
PRT- 01 - 30 - ES - H1
Options:
Body material
High temperature
Standard Blank: Aluminum
up to +356 °F
ES: 316 stainless steel
ESR: 303 stainless steel
Sliding pads
Body material
Inner-Ø [mm]
Slewing Ring
Blank: iglide® J
Sliding pads
H1: iglide® H1,
H * High temperature
ESD: iglide® F2,
Type
ESD-compliant
T2
Stainless steel version ESD compliant s1
d2
d
D1
d1
D
H * Detail * Accessories
➤ Page 654
T2
R2 versions on request
T1
BB
s1
d2
d
D1
d1
D
T1
K1
s2
h
Dimensions [mm]
Detail *
Part No. D10) D1 d1 d d2 H h T1 T2 S1 S2 K1 R1 R2 B
R1
±0.2 for screw
PRT-01-20-... 80 70 31 R2
20 60 24 8 6 x 60 ° 6 x 60 ° M4 4.5 DIN 7984 M4 30 20 3.5
PRT-01-30-... 100 B B
91 42.5 30 82 29 10 8 x 45 ° 8 x 45 ° M4 4.5 DIN 7984 M4 41 29 4.5
PRT-01-50-... 150 135 65 50 120 33 10 8 x 45 ° 16 x 22.5 ° M6 6.6 ISO 4762 M6 60 46.5 4.5
PRT-01-60-... 160 145 74 60 130 33 10 10 x 36 ° 20 x 18 ° M5 5.5 ISO 4762 M5 65 51.5 4.5
PRT-01-100-... 185 170 112 100 160 34 12 12 x 30 ° 16 x 22.5 ° M5 5.5 ISO 4762 M5 80 69 5.5
PRT-01-150-... 250 235 165 150 220 35 12 12 x 30 ° 16 x 22.5 ° M5 5.5 ISO 4762 M5 110 96.5 5.5
PRT-01-200-... 300 285 215 200 274 38 15 12 x 30 ° 16 x 22.5 ° M6 6.6 ISO 4762 M6 137 124 7.0
PRT-01-300-... 450 430 320 300 410 42 15 12 x 30 ° 16 x 22.5 ° M8 9.0 DIN 7984 M8 205 186.6 7.0
Please add suffix "-H1" for the high temperature version or suffix "-ESD" for ESD-compliant slewing ring bearings
Stainless steel
Inner-Ø [mm]
Slewing Ring
(suffix "-ES")
Tooth profile
Standard
H
version
X X
type
H
S1
X X
T2
S1
T2
D1
d2
d1
D
R1
T1
D1
d2
d1
D
d
K1
R2
B
R1
T1
K1
R2
S2
B
h
B
Dimensions [mm]
S2
Part No. D1 d1 d d2 h T1 T2 S1 S2 K1 R1 R2 B H
for screw
PRT-20-... 70 31.0 20 60 18 6x60 ° 6x60 ° M4 4.5 DIN 7984 M4 30 20.0 3.5 (26.0)
PRT-30-... 91 42.5 30 82 21 8x45 ° 8x45 ° M4 4.5 ISO 4762 M4 41 29.0 4.5 (30.5)
PRT-60-... 145 74.0 60 130 23 10x36 ° 20x18 ° M5 5.5 ISO 4762 M5 65 51.5 4.5 (34.5)
PRT-100-... 170 112.0 100 160 25 12x30 ° 16x22.5 ° M5 5.5 ISO 4762 M5 80 69.0 5.5 (36.0)
PRT-150-... 235 165.0 150 220 25 12x30 ° 16x22.5 ° M5 5.5 ISO 4762 M5 110 96.5 5.5 (37.5)
PRT-200-... 285 215.0 200 274 30 12x30 ° 16x22.5 ° M6 7.0 ISO 4762 M6 137 124.0 7.0 (41.5)
PRT-300-... 430 320.0 300 410 30 12x30 ° 16x22.5 ° M8 9.0 ISO 4762 M8 205 186.5 8.5 (43.5)
Spur gearing DIN3967 Toothed belt profile Toothed belt profile Toothed belt profile
AT10 T10 HTD5M (-20)/HTD8M
Order key
Options:
Type Size Options Body material
AL: Aluminum
PRT - 02 - 20 - AL - A180 ES: 316 Stainless steel
LC: Low-cost
P: Solid plastic
Body material
Inner-Ø [mm]
Slewing Ring
Standard Stainless steel version
Outer rings
Outer rings
Blank: iglide® J4
A180: iglide® A180,
Type
FDA-compliant
H
Low-cost version Solid plastic version
T2
D1
d1
d2
D
d
T1
K2 K1
FDA compliant
s2
h
Slewing ring with extremely low weight
Outer ring made from anodized aluminum,
316 stainless steel (on request) or iguton G
Outer rings made from iglide® J4 or FDA-compliant iglide® A180
30 % lighter with plastic screws
Dimensions [mm]
Part No. D D1 d1 d d2 H h T1 T2 S2 K1 K2
for screw for screw nut
PRT-02-20-£ 80 70 31 20 60 16 5 6 x 60 ° 6 x 60 ° 4.5 DIN 6912 M5 DIN 439 M5
PRT-02-30-£ 100 91 42.5 30 80 19 6 8 x 45 ° 8 x 45 ° 4.5 DIN 7984 M5 DIN 439 M5
PRT-02-50-£ 150 135 65 50 120 20 6 16 x 22.5 ° 8 x 45 ° 6.6 Through hole 6.5 mm
PRT-02-60-AL 160 145 86.0 60 130 30 10 12 x 30 ° 20 x 18 ° 5.5 Counter-bore Ø16 and 6.5 deep
Slewing ring bearing with square flange for direct mounting on flat surfaces
No intake-hole necessary d1
S2 h2
T1
D
A
E
d
S1
E h1
A H
Dimensions [mm]
Part No. d d1 d2 D A E H h1 h2 T1 S1 S2 K1
for screw
PRT-01-20-SQ 20 31 60 62 65 50 26 18 2 6 x 60 ° M4 4.5 DIN 7984 M4
PRT-01-30-SQ 30 42.5 82 84 85 65 30.5 10 1.5 8 x 45 ° M4 4.5 DIN 7984 M4
S1
K1
D1
d1
d2
D
d
T1
T2
Max. torque moment: 5 Nm Slewing ring with collar clamp PRT-01-30-C PRT-01-30-C
Dimensions [mm] R2
Part No. D D1 d1 d d2 H h T1 T2 S1 S2 K1
B
B
for screw
PRT-01-30-C 100 91 R1 42.5 30 82 36 10 6 x 45 ° 8 x 45 ° M4 4.5 DIN 7984 M4
R2
d2
K1
d
B
K1
X
Slewing ring bearing with dust seal (-D: one-sided, -DD: both-sided)
B
H
S2
S1
R1
R2
T1
T2
d2
B
K1
d
B
K1
X
H
d1
S2 R1
D1 S1
D
d2
T1
K1
T2
Dimensions [mm]
K1
X
H
PRT-01-100-D/DD 185 170 112 100 160 34 12 12 x 30° 16 x 22.5° M5 5.5 ISO 4762 M5 80 69 5.5
D1
10)
Tolerance according to DIN ISO 2768 mK
D1
653
D
D
iglide®
iglide PRT - Product range - Special geometries
®
T3
D1
d2
T2
PRT
K1
d1
d
X
Type 01
h
S2 S1
H
S1 S2 T1
H
Slewing ring bearing with angle limit - set the angle limit by yourself
X
d
K1
T2
T3 d2
T3
T2
T1 S2 S1 R1
Detail X
B B
h
X
d
d1
K1
d2
D1
R2
Angle range in 2° steps D
Dimensions [mm]
Detail X
B B
Part No. D D1 d1 d d2 H h T1 T2 T3 S1 S2 K1 R1 R2 B
R2
PRT-01-60-TS 180 160 74 60 130 33 10 10 x 36° 20 x 18° 36 x 10° M5 5.5 ISO 4762 M5 65 51.5 4.5
D1
db
dp
Dimensions [mm] hp
Part No. dp hp dz hz D1 T1 db
PRT-AZ-30 55 5 10 15 42.5 8x45° 4.5
PRT-AZ-60 90 5 14 15 74 10x36° 5.5
T1
T2
Dimensions [mm] – other dimensions similar to standard type PRT-01 ➤ page 650
Part No. 11) D D1 S2
PRT-01-100-M-ARG 205 185 5.5
PRT-01-100-M-ARGG 205 185 M6
PRT-01-100-M-ARGS 205 185 5.5
PRT-01-200-M-ARG 320 300 7.0
PRT-01-200-M-ARGG 320 300 M8
PRT-01-200-M-ARGS 320 300 7.0
11)
Ending: -G standard, -GG thread- or -GS counter-bore
Manual clamp
K1
D
D1
K1
T2
w
D1
D
T2
D1
w
W
h
T2
T2
W
W
K1
D
PRTgkwith fitted
D1
h manual clamp
H
gk W
K1
h
H
gk
PRT-HK-30
gk PRT-HK-60/100/200
h
Dimensions [mm]
Part No. D D1 T2 K1 H h gk W
for screw
PRT-HK-30 100 91 45 ° Ø 4.5 8 3.2 M5 60 °
PRT-HK-60 160 145 18 ° DIN 7984 M5 – 10 M6 35 °
PRT-HK-10012) 205 185 22.5 ° DIN 7984 M5 – 10 M6 40 °
PRT-HK-200 12)
320 300 22.5 ° DIN 7984 M6 – 10 M6 40 °
12)
To be connected only with enlarged outer ring
D3
D1
Aluminum Plastic D h1
PRT with mounted
spacing ring
Dimensions [mm]
Part No.39) D D1 T2 S2 D3 h1
PRT-01-20-DR 80 70 6 x 60 ° 4.5 62 10
PRT-01-30-DR 100 91 8 x 45 ° 4.5 84 11
PRT-01-60-DR 160 145 20 x 18 ° 5.5 132 13
PRT-01-100-DR 185 170 16 x 22.5 ° 5.5 162 13
PRT-01-150-DR 250 235 16 x 22.5 ° 5.5 222 13
PRT-01-200-DR 300 285 16 x 22.5 ° 7.0 276 13
PRT-01-300-DR 450 430 16 x 22.5 ° 9.0 412 15
39)
Please add suffix “-POM” for plastic version (not available for sizes 150 and 300)
0.00
2.5 +- 0.25
0.0
39.5 +- 0.5
1
0.00
2.5 +- 0.25
0.5
39.5 +- 0.0
15 ± 0.5 0.0
15 +- 0.5
1 10°
15 ± 0.5 0.0
1 15 +- 0.5
Slide elements made of iglide® J 34.5 +- 0.0
10°0.5
34.5 +- 0.0
0.5
Technical data
Size 20 Size 30 Size 50
RLD-20-S-38-ST RLD-30-S-50-ST RLD-50-S-48-ST
Weight [g] 410 730 1,900
Reduction gearing 38:1 50:1 48:1
Axis distance [mm] 31 40 63
Efficiency > 0.25 > 0.25 > 0.25
Breakaway torque [cNm] <5 <7 < 10
Technical data
Size 20 Size 30 Size 50
RLD-20-A-38-ST RLD-30-A-50-ST RLD-50-A-48-ST
Weight [g] 320 570 1,550
Reduction gearing 38:1 50:1 48:1
Axis distance [mm] 31 40 63
Efficiency > 0.25 > 0.25 > 0.25
Breakaway torque [cNm] <5 <7 < 10
3 versions
Standard: Aluminum PRT (PRT-02-xx-AL),
aluminum worm shaft (AL hard anodized). Application, for
B2
T
worm shaft made from plastic RN33
Application, for example, for manual adjustments
ØF High end: PRT design 01 (PRT-01-xx), aluminum worm shaft
(AL hard-anodized), high rigidity.
H1
L1 L2 B1
Dimensions
Part no. ØT ØS ØP ØF L1 L2 B1 B2 H1 G1 G2
Symmetrical - Standard
RLD-20-S-38-ST 20 8 60 31 80 12 35 10.5 90 M4 3 x M5
RLD-30-S-50-ST 30 10 80 42.5 100 12 45 12.5 110 M4 4 x M5
RLD-50-S-48-ST 50 15 120 60 150 13 60 13 170 M6 4 x M6
Symmetrical - Low cost
RLD-20-S-38-LC 20 8 60 31 80 12 35 10.5 90 M4 3 x M5
RLD-30-S-50-LC 30 10 80 42.5 100 12 45 12.5 110 M4 4 x M5
RLD-50-S-48-LC 50 15 120 60 150 13 60 13 170 M6 4 x M6
Symmetrical - High end
RLD-20-S-38-HE 20 8 60 31 80 12 35 16 90 M4 6 x M4
RLD-30-S-50-HE 30 10 80 42.5 100 12 45 19.5 110 M4 8 x M4
RLD-50-S-48-HE 50 15 120 65 150 13 60 21.5 170 M6 8 x M6
3 versions
Standard: 1 aluminum PRT (PRT-02-xx-AL),
aluminum worm shaft (AL hard anodized)
B3
ØT
Low cost: 1 low-cost PRT (PRT-02-xx-LC),
worm shaft made from plastic RN33
ØF Application, for example, for manual adjustments
High end: 1 PRT design 01 (PRT-01-xx), aluminum worm shaft
H1
Dimensions
Part no. ØT ØS ØP ØF L1 L2 B1 B2 H1 G1 G2
Asymmetrical - Standard
RL-D-20-A-38-ST 20 8 60 31 80 12 35 10.5 90 M4 3 x M5
RL-D-30-A-50-ST 30 10 80 42.5 100 12 45 12.5 110 M4 4 x M5
RL-D-50-A-48-ST 50 15 120 60 150 13 60 13 170 M6 4 x M6
Asymmetrical - Low cost
RL-D-20-A-38-LC 20 8 60 31 80 12 35 10.5 90 M4 3 x M5
RL-D-30-A-50-LC 30 10 80 42.5 100 12 45 12.5 110 M4 4 x M5
RL-D-50-A-48-LC 50 15 120 60 150 13 60 13 170 M6 4 x M6
Asymmetrical - High end
RL-D-20-A-38-HE 20 8 60 31 80 12 35 16 90 M4 6 x M4
RL-D-30-A-50-HE 30 10 80 42.5 100 12 45 19.5 110 M4 8 x M4
RL-D-50-A-48-HE 50 15 120 65 150 13 60 21.5 170 M6 8 x M6
B1
Adaptable to various motors, standard option: stepper motor
NEMA17 / 23 / 23XL
L2 INI kit for zero position optionally adaptable
L1 B2
Dimensions
NEMA 17
Part No. ØS L1 L2 B1 B2
NEMA17 Standard
RLD-20-MK-C-N17-02 8 110.4 40 42 42
RLD-30-MK-C-N17-02 10 110.4 40 42 42
NEMA17 stepper motor with encoder
RLD-20-MK-C-N17-01 8 110.4 40 42 42
RLD-30-MK-C-N17-01 10 110.4 40 42 42
NEMA17 with stranded wires
RLD-20-MK-C-N17-00 8 110.4 40 42 42
RLD-30-MK-C-N17-00 10 110.4 40 42 42
NEMA 23
Part No. ØS L1 L2 B1 B2
NEMA23 Standard
RLD-30-MK-C-N23-02 10 140 42 56.4 56.4
RLD-50-MK-C-N23-02 15 146 48 60 60
NEMA23 stepper motor with encoder
RLD-30-MK-C-N23-01 10 140 42 56.4 56.4
RLD-50-MK-C-N23-01 15 146 48 60 60
NEMA23 with stranded wires
RLD-30-MK-C-N23-00 10 140 42 56.4 56.4
RLD-50-MK-C-N23-00 15 146 48 60 60
NEMA23XL
RLD-50-MK-C-N23XL-02 15 158.5 48 60 60
RLD-50-MK-C-N23XL-01 15 158.5 48 60 60
RLD-50-MK-C-N23XL-00 15 158.5 48 60 60
Technical data
Joint Size 20 Size 30 Size 50
RLD-20-S-38-XX RLD-30-S-50-XX RLD-50-S-48-XX
Motor + NEMA17 + NEMA17 + NEMA23 + NEMA23 + NEMA23XL
Motor type Stepper motor
Weight (with standard joint) [g] 890 1.1140 1,860 2,540 2,970
Max. radial torque strength (short term) [Nm] 5 6 12 21 38
Max. radial torque strength (long term) [Nm] 4 5 8 18 33
Max. speed (at max. load) [rpm] 5 4 4 4 4
Max. axial dynamic load (horiz. installation) [N] > 500 > 700 > 700 > 1,200 > 1,200
Bar stock
Tribo-Tape
Tribo-Filament
...
...
...plastics
Bar stock, Tribo-Tape, Tribo-Filament | Product overview
For free design
iglide® A160 – iglide® A180 – iglide® A181 – iglide® A350 – iglide® A350 –
highly media resistant, low the general purpose solution food grade material, compliant the FDA-compliant high- as plate material
cost material for the medical and food with FDA specifications and temperature material
industries (FDA compliant) EC Directive 10/2011
➤ Page 671 ➤ Page 671 ➤ Page 671 ➤ Page 672 ➤ Page 672
➤ Page 676 ➤ Page 676 ➤ Page 676 ➤ Page 677 ➤ Page 677
Standard material: Standard material - Black: Highest wear resistance: High temperature resistant:
iglide® I180-PF iglide® I180B-PF iglide® I170-PF iglide® J260-PF
➤ Page 673 ➤ Page 673 ➤ Page 674 ➤ Page 675 ➤ Page 675
➤ Page 677 ➤ Page 678 ➤ Page 678 ➤ Page 678 ➤ Page 679
Temperature range:
-58°F (-50°C) up to 194°F (+90°C)
for standard iglide® J
Mechanical processing -148°F (–100°C) up to 482°F (+250°C)
and cutting (depending on material)
20 Materials
Round bars: Ø 10–100 mm
Plate thickness: 2–40 mm
Tubes: up to 150 mm outer Ø
Tempering
Interim tempering reduces inner tensions caused by the machining
process, and thus creates narrower tolerances. In the end, the
optimum values depend on the volume of material machined,
the machining parameters and the geometric design of the end
product, which should be determined by tests.
As the plastic has low thermal conductivity, the plastic bar stock
has to be heated slowly.
Tempering
iglide® materials
When possible, the entire bar stock should be evenly heated. temperatures
Therefore, it is important to achieve the appropriate temperatures A180, A181, J, J2, M250
248°F (+120 °C)
for material tempering indicated below over a period of 3 – 4 hours J3, J4, J200, R
by slowly heating the part from room temperature. Depending on 266°F (+130 °C) J260
the thickness of the part, this temperature should be maintained 356°F (+180 °C) F2, P210, T220, L280
392°F (+200 °C) A350, H1, J350
for 1 hour per cm of wall thickness.
428°F (+220 °C) T500111)
If the machined part cools too quickly, tension can once again be
induced. This is avoided by using a slow cooling process with a
111)
In the case of iglide® T500, the 428°F (220 °C) per cm of wall
thickness must be maintained for 2 hours.
maximum reduction of 68°F (20 °C) per hour until room temperature
is reached.
Dimensions (mm)
Order key
Ø Lengths16) Part No. Ø Lengths16) Part No.
for round bars
iglide® A160 iglide® A181 Type Dimensions
SA180-30 SA181-50
40 100 to 1,000 SA180-40
50 100 to 1,000 SA180-50
60 100 to 1,000 SA180-60
80 100 to 1,000 SA180-80
100 100 to 1,000 SA180-100
16)
Minimum length 100 mm - maximum length 1 m
iglide® A350
Temperature resistant, FDA-compliant
Dimensions (mm)
iglide® H1
iglide® F2
For special plain bearings and bearing elements under
Used to prevent electrostatic charges
extreme conditions
Dimensions (mm)
iglide® F2 iglide® H1
iglide®-Material
Length16) (mm)
Outer Ø (mm)
Length (mm)
Width (mm)
Bar stock
Plate
(mm)
iglide® J
The general purpose solution with optimum wear
resistance and outstanding efficiency
Dimensions (mm)
iglide®-Material
iglide®-Material
Length16) (mm)
Length16) (mm)
Outer Ø (mm)
Outer Ø (mm)
Length (mm)
Width (mm)
Bar stock
Bar stock
Round
Plate
(mm)
Dimensions (mm)
Length16) (mm)
Outer Ø (mm)
iglide® J4
Dimensions (mm)
Length16) (mm)
Outer Ø (mm)
iglide® J350
Dimensions (mm)
Order key
Ø Lengths16) Part No.
for round bars
iglide® P210 Type Dimensions
Length16) (mm)
iglide® R
iglide® M250
Dimensions (mm)
Order key
Ø Lengths16) Part No.
for round bars
iglide® T220 Type Dimensions
Length16) (mm)
iglide® UW160
Bar stock
Dimensions (mm)
Order key
Ø Lengths16) Part No. Ø Lengths16) Part No.
for round bars
iglide® L280 iglide® T500 Type Dimensions
Length16) (mm)
16)
Minimum length 100 mm - maximum length 1 m
• Choice of 3 materials
• Self-lubricating and maintenance-free
• Wear resistant
• Easy to cut
• Adhesive version available
• Only 0.5 mm thickness
683
iglide® Tribo-Tape - Advantages
Multi-purpose: First iglide® Tribo-Tape
Wear resistant
Available from stock
Detailed information about delivery time online.
Low coefficients
of friction
Up to +158 °F
Order key
G2 = High Temp
Thickness [mm]
iglide® material
Adhesive back
G1 = Standard
up to +158 °F
Width [mm]
5 = 0.5 mm
iglide® B160:
up to +158 °F
Tape
The low cost iglide® A160 Tribo-Tape has very high wear 500
resistance compared to similar, thin plastic films.
400
Black iglide® B160 Tribo-Tape material for stressed areas
Wear/Weight decrease
Especially where the iglide® Tribo-Tape is a visible part, the new
PEEK mod. 1
PEEK mod. 2
200
iglide® A160
has been improved once again. [mg/km]
iglide® V400 tape is not only highly wear resistant but also extremely 100
PEEK
PET
PC
media and temperature resistant. In fact, it has been proven in tests
to be up to 10 times more wear resistant than special products 0
for machine beds. Rotating wear against stainless steel pin (1.4305)
F = 35 N, v = 0.5 m/min
30
25
Wear/Weight decrease
20
15
10
iglide® V400 PTFE-bronze
[mg/km]
0
Linear wear against stainless steel pin (1.4305)
F = 35 N, v = 0.5 m/min
Widths available Widths available with G1 adhesive Widths available with G2 adhesive
A160 Part No.
[mm] [mm] [mm]
A160T-5- 20, 50, 100, 120, 500 20, 50, 100 50
A160-T-1.0- 500 — 500
• Choice of 4 materials
• Suitable for commercially available 3D printers using
FDM process
• 1.75 mm and 3 mm thickness in stock
• Up to 50 times more abrasion resistant than
conventional 3D print materials
687
iglide® Tribo-Filament - Advantages
Print your own real iglide® products
Standard material:
iglide® I180-PF
iglide® Tribo-Filament for
3D printing – Wear resistant
Nozzle temperature: The materials that have been specially developed for 3D
+428°C to +482°C printing are up to 50 times more abrasion-resistant than
conventional 3D print materials. This provides a new degree
Also suited for of freedom when designing gliding components subject to
tight feed radii wear: custom parts and prototypes from a 3D printer with
a tested service life.
Wear-resistant
iglide® I180B-PF
Suitable for commercially available 3D printers using
Black
FDM process
1.75 mm and 3 mm thickness
Nozzle temperature:
+428°F to +482°F Typical industries and applications
Prototype constructions Small batches
Construction tests, etc.
Diameters
1.75 and 3 mm
More information about 3D printing
➤ www.igus.com/3D-printer
Highest wear resistance:
iglide® I170-PF Depending on material:
iglide® I180-PF: –40°F up to +176°F
iglide® I180B-PF: –40°F up to +176°F
Nozzle temperature:
iglide® I170-PF: –40°F up to +167°F
+428°F to +482°F iglide® J260-PF: –148°F up to +248°F
4 Materials: 1.75 mm and 3 mm
(for iglide® I180-PF & l80B-PF)
Large feed radii
(min. 50 mm)
Available from stock
Detailed information about delivery time online.
Nozzle temperature:
+500°F to +536°F
Good resistance
to media
iglide® l180-PF iglide® l170-PF
iglide® l180B-PF
400 400
350 350
300 300
iglide® J (molded)
iglide® J (molded)
250 250
Wear rate [μm/km]
iglide® I180-PF
iglide® I170-PF
iglide® I180-PF
200 200
150 150
PC-ABS
PC-ABS
100 100
ABS
ABS
PLA
PLA
PC
PC
50 50
0 0
Wear pivoting: v = 1.97 fpm; p = 145 psi; ß = 60° Wear linear: v = 1.97 fpm; p = 145 psi; l = 5 mm
Wear
The iglide® Tribo-Filaments are up to 50 times more wear resistant
than conventional materials (PLA/ABS) for 3D printing. The highest
level of Tribo-Filament wear resistance is achieved with iglide ®
I170-PF and is very similar to that of injection molded bearings
under low to medium loads. Even the wear rate of iglide® l180-
PF components is far superior to that of conventional 3D printing
materials. They are also easier to process than iglide® l170-PF.
Filament on a spool part no. Filament on a spool part no. Filament on a spool part no.
I180-1.75-250 I170-1.75-250 J260-1.75-250
I180-3.00-250 I170-3.00-250 J260-3.00-250
I180-1.75-750 I170-1.75-750
I180-3.00-750 I170-3.00-750
Ø [mm · 100]
are produced
Complete processing instructions online
...
...plastics
xiros® Ball bearings - Overview
xiros® radial deep-groove ball bearings – Standard material xirodur® B180
➤ Page 704 ➤ Page 706 ➤ Page 706 ➤ Page 706 ➤ Page 706
High temperature and For low loads High temperatures High chemical resistance Conductive
chemical resistant xirodur® A500 PEEK cage xirodur® A500, xirodur® C160 xirodur® F180
xirodur® A500, PEEK cage PAI balls PA cage PP cage PA cage
➤ Page 708 ➤ Page 708 ➤ Page 708 ➤ Page 710 ➤ Page 712
With single flange With double flange Conductive System-solution End cap
xirodur® B180 xirodur® B180 xirodur® F180 Aluminum tube with flange xirodur® B180
PA cage PA cage PA cage ball bearing PA cage
➤ Page 720 ➤ Page 720 ➤ Page 720 ➤ Page 722 ➤ Page 724
Standard Double row Thrust washer Polymer ball transfer unit Axial polymer ball transfer
POM balls unit
with spherical ball
➤ Page 726 ➤ Page 726 ➤ Page 727 ➤ Page 728 ➤ Page 728
➤ Page 706
ESD protection & Detectable For tobacco industry Quiet and for high speeds Higher temperatures
FDA compliant xirodur® M180 xirodur® T220, xirodur® D180 xirodur® G220
xirodur® F180, PE cage xirodur® M180 cage PP cage PA cage PP cage
➤ Page 712 ➤ Page 714 ➤ Page 715 ➤ Page 716 ➤ Page 717
Other designs
Spherical outer diameter Spherical outer diameter Double row Multi axis Skate wheel
xirodur® B180 xirodur® M180 xirodur® B180 xirodur® B180 xirodur® B180
PP balls PA cage
➤ Page 723 ➤ Page 723 ➤ Page 718 ➤ Page 719 ➤ Page 725
Material data,
chemical resistance
table and tolerance
recommendation
➤ Page 702
GUIDE ROLLERS
The xiros® polymer ball bearings are 50% lower in
price than the bearings previously used here
Cost-effective
made from xirodur® B180 with B180 cage Self-lubricating
polymer ball
and glass or stainless steel balls
➤ Page 704
Chemical resistant
bearings
made from xirodur® A500 with PEEK-cage xiros® polymer ball bearings have revolutionized the
and glass or stainless steel balls
market. The maintenance free dry-running and the use
➤ Page 708
of xirodur® high performance polymers successfully solve
many applications where conventional metal ball bearings
are not effective. xiros® ball bearings are the only plastic
ESD protection & FDA compliant
ball bearings in the world which use specially developed
made from xirodur® F180 with
PE-cage and stainless steel balls xirodur® tribo-polymers.
➤ Page 712 Self-lubricating and maintenance free
High corrosion resistance
Free from metal (due to the use of glass and plastic
Detectable balls), therefore non-magnetic
made from xirodur® M180 with xirodur® For temperatures up to +302 °F
M180 cage and stainless steel balls High chemical resistance, suitable for wash-down
➤ Page 714 Lightweight
Electrically insulating (or conductive)
FDA compliant (depending on material)
Flange ball bearings Predictable service life
Standard (xirodur® B180),
conductive (xirodur® F180)
Typical application areas:
➤ Page 720
Packaging Textile industry Test engineering and
quality assurance Optical industry Model making
Medical technology
Axial ball bearings
made from xirodur® B180,
different types and designs Online product finder
➤ Page 726 ➤ www.igus.com/xiros-finder
max. 302°F
F
Polymer ball transfer units min. -40°F
for self-lubricating transport of
sensitive products 7 Materials
➤ Page 728 17 product types
based on DIN 625. The self-lubricating and maintenance free ball xiros® radial deep groove ball bearings
bearings consist of four components: The other designs include convex rollers, which can run directly on
a profile, casters, a multi-bearing for linear and radial movements,
The outer- and inner races flange bearings designed, for example, for installation in tube ends
The suitability of a xiros plastic ball bearings is largely determined
®
and double-row bearings for absorbing higher forces.
by the materials of the two races. These are made from igus®
triboplastics to maximize service life and minimize friction. You can Pillow block and flange bearings
currently choose from six different materials. They allow different This range is made up by combining xiros® plastic ball bearing
values of application temperature, chemical resistance and price. with the igubal® pillow block and flanged housings, resulting in a
The table with material data (Page 702) gives exact information. higher flexibility in terms of installation of the bearings. The pre-
finished bearing housing make it easy for the user to use these
maintenance free components. Both flanged and pillow block are
Outer race available as fixed or as pivoting design. The difference between
the two options is that the pivoting type can compensate for shaft
and/or bearing misalignment. A spherical outer race is pressed into
Inner race
the bearing housing, ensuring self aligning action. If necessary, the
inner bearing can be pivoted in all directions. Possible misalignment
Cage of two bearing points lying together can thereby be compensated.
Balls
The cage
The material of the ball bearing cage must fit well to the application.
The various material options have quite different chemical and
temperature resistance values. The cage materials are compatible
with all the different race options within xiros®.
The balls
We offer stainless steel, glass or plastic balls. This produces a large
difference in mass, which in turn affects smoothness, weight and
chemical resistance. Steel balls (stainless steel) are cost-effective,
chemical resistant, but with the most weight. Glass balls are
used to give a metal free solution. They are also very resistant to
chemicals, are non-magnetic and have an average weight. Plastic
balls have significant advantages in weight, size and quiet running
characteristics. Depending on the polymer used, plastic balls can
have excellent chemical resistance.
Two of our test benches for xiros® plastic ball bearings at igus®
bearings laboratory
xirodur® igumid
General properties Unit B180 A500 C160 F180 M180 T220 D180 G220 G
Density g/cm3 1.41 1.28 1.11 1.41 1.63 1.28 1.24 1.14 1.37
Color white brown opaque black blue beige blue silver black
Max. moisture absorption
% weight 0.2 0.3 0.1 0.2 0.2 0.3 0.5 2.1 1.4
at +73 °F/50 % r.h.
Max. water absorption % weight 0.7 0.5 0.2 0.7 0.6 0.5 1.4 8.9 5.6
Mechanical properties
Modulus of elasticity psi 362,594 522,135 275,570 362,594 362,594 261,067 18,854 435,113 1,131,294
Tensile strength at +68°F psi 68 140 35 68 68 65 n. v. n. v. 240
Shore-D Hardness 77 83 67 77 77 76 51 n. v. 79
Electrical properties
Specific volume resistance1) Ωcm > 1014 > 1014 > 1014 > 107–109 2) > 109 > 1010 > 1014 > 1013 > 1011
Surface resistance1) Ω > 1014 > 1013 > 1014 > 107–109 2) > 109 > 1010 > 1014 > 1012 > 1011
Thermal properties of xiros® polymer ball bearings
Max. long term application temperature °F +176 +302 +158 +176 +176 +212 +176 +212 +248
Min. application temperatures –148 (PEEK)
°F –40 0 –40 –40 –40 –58 –40 –40
(in combination with cage material) –40 (PA)
1)
nly valid for xirodur® F180: the good conductivity of this material favours, under certain conditions, the corrosion generation on metallic parts.
O
2)
Depending on the geometry
Dirt
resistant
Chemical
resistant
For high
temperatures
Smooth running
Low moisture
absorption
Seawater
resistant
Cost-effective
Conductive
+ ESD protection
Metal free
d1
d1
PA cage, PA cage,
b1 b1
stainless steel balls glass balls d2 d2
Temperature range
-40°F to +176°F
Order key
Width of bearing
(Based on 1/32”)
E = stainless steel
Cage material
Race material
G = glass
Ball material
Ball bearing
B180
Inch
Size
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic E G
[lbs] [lbs] [lbs] [rpm] [g] [g]
0620 7 10 11 3700 1.6 1.0
0820 9 10.5 11.5 3500 1.3 –
0824 11 9 16.5 3200 1.6 1.0
1228 12 9 20 2200 3.9 –
1236 14 25 27 1900 4.9 4.9
1636 16.5 13 33.5 2000 7.6 5.2
2044 17.5 11 43 1600 11 7.9
2452 18 9 65 1400 20.1 13.6
3264 26 29 80 1050 27.3 27.3
Dimensions [mm]
Part No. Part No. Inner Outer Width Cage/ball material combination
Without shield With shield Ø Ø
PA/E/G d1 d2 b1 PA/G PA/E PE/E B180/G B180/E
B623B££ BC623B££ 3 10 4
B624B££ 4 13 5
B625B££ 5 16 5
B626B££ BC626B££ 6 19 6
B629B1E 9 26 8
B608B££ BC608B££ 8 22 7
B688B££ 8 16 5
B6800B3E 10 19 5
B6000B££ BC6000B££ 10 26 8
B6200B££ 10 30 9
B6801B3E 12 21 5
B6001B££ BC6001B££ 12 28 8
B6201B££ 12 32 10
B6802B3E 15 24 5
B6002B££ 15 32 9
B6202B££ BC6202B££ 15 35 11
B6003B££ BC6003B££ 17 35 10
B6203B££ 17 40 12
B6004B££ BC6004B££ 20 42 12
B6204B££ 20 47 14
B6005B££ BC6005B££ 25 47 12
B6205B££ 25 52 15
B6006B££ 30 55 13
B6007B££ 35 62 14
B6008B££ 40 68 15
B6009B££ 45 75 16
B6010B££ 50 80 16
B6011B££ 55 90 18
B6012B££ 60 95 18
Order key
Dimensions acc.
b1 b1
d2 d2 1 = PA
Cage material
Race material
3 = xirodur® B180
to DIN 625-1
Ball material
Ball bearing
With cover
5 = PE
AA Ball material
E = stainless steel
B180
G = glass
With shield
d11
d22
d
d
The order key shows part with available cover option “BC
Without the cover option omit “C”. Example: B623B1E
AA b1
b1
Technical data
Size Maximum static Bearing load Maximum speed Weight With shield
bearing load axial static dynamic E G E G
[lbs] [lbs] [lbs] [rpm] [g] [g] [g] [g]
623 7 6 8 4,500 0.4 0.3 0.4 0.4
624 9 7 10 4,000 1.0 0.9 – –
625 17 9 12 3,700 1.6 1.0 – –
626 21 9 13 3,200 2.2 1.7 2.5 1.8
629 9 25 29 2,200 6.1 – – –
608 37 13 19 2,200 3.9 2.6 4.0 2.7
688 30 11 15 1,760 3.1 2.1 – –
6800 13 9 11 3,600 1.6 – – –
6000 64 29 31 2,200 6.1 4.0 6.3 4.1
6200 64 19 27 1,900 7.8 5.2 – –
6801 13 13 17 3,250 1.9 – – –
6001 71 31 38 2,000 6.9 4.5 7.1 –
6201 71 24 33 1,750 8.8 5.9 – –
6802 13 18 21 2,900 2.5 – – –
6002 76 34 44 1,800 8.9 6.2 – –
6202 76 33 44 1,600 11.6 8.2 12.8 8.9
6003 81 54 74 1,600 11.1 7.9 11.5 8.4
6203 81 40 56 1,400 14.4 10.2 – –
6004 90 56 72 1,400 20.2 13.6 20.8 14.2
6204 90 47 66 1,150 26.2 17.7 – –
6005 117 63 85 1,200 23.9 16.7 24.7 17.5
6205 117 54 81 1,050 35.2 24.6 – –
6006 144 85 112 1,000 35.0 24.2 – –
6007 162 103 135 850 47.0 31.3 – –
6008 180 117 153 750 56.3 39.1 – –
6009 202 135 180 650 71.5 48.6 – –
6010 216 153 202 600 83.1 56.4 – –
6011 225 162 214 550 125.2 84.4 – –
6012 247 180 225 500 129.6 85.6 – –
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 PEEK/E PEEK/G PEEK/P PA/E PA/G
B623A££ 3 10 4
B624A££ 4 13 5
B626A££ 6 19 6
B608A££ 8 22 7
B6000A££ 10 26 8
B6002A££ 15 32 9
B6004A££ 20 42 12
Order key
d1
d1
B 623 A 1 E 1 = PA
7 = PEEK
Dimensions acc.
Ball material
Cage material
Race material
E = stainless steel
to DIN 625-1
b1 b1
Ball material
Ball bearing
d2 d2 G = glass
P = polyamide-imide
A500
Technical data
Size Maximum static Bearing load Maximum Weight
bearing load axial static dynamic static dynamic speed PEEK/ PEEK/ PEEK/ PA/ PA/
PEEK/P PEEK/P E G P E G
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [rpm] [g] [g] [g] [g] [g]
623 7 – 7 9 – – 5,000 0.4 0.3 – 0.4 0.3
624 13 – 9 12 – – 4,550 1.0 0.9 – 1.9 0.9
626 28 7 13 18 3 4 3,400 2.3 1.6 1.4 2.3 1.6
608 49 12 16 22 4 6 2,700 3.7 2.4 2.2 3.7 2.4
6000 85 21 23 31 6 8 2,100 6.0 3.8 3.4 6.0 6.0
6002 99 27 36 38 7 9 1,900 9.1 5.2 5.6 9.1 9.1
6004 146 36 56 72 14 20 1,700 19.7 13.2 11.7 19.7 19.4
Order example:
B623A1E = ball bearing with PA cage and stainless steel ball
PP cage, PP cage,
stainless steel balls glass balls
Temperature range Temperature range
32°F to +176°F 32°F to +176°F
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material
combination
d1 d2 PP/ES PP/GL
B623C2£ 3 10 4
B626C2£ 6 19 6
B608C2£ 8 22 7
B6000C2£ 10 26 8
B6002C2£ 15 32 9
B6003C2£ 17 35 10
Order key
Dimensions acc.
E = stainless steel
Cage material
Race material
G = glass
to DIN 625-1
b1 b1
Ball material
Ball bearing
d2 d2
C160
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynanic PP/ES PP/GL
[lbs] [lbs] [lbs] [rpm] [g] [g]
623 6 4 6 4,000 0.4 0.3
626 18 7 9 2,600 2.1 1.4
608 33 10 13 2,200 3.4 2.2
6000 56 15 21 1,900 5.6 3.5
6002 65 21 27 1,600 8.1 4.2
6003 72 25 36 1,400 9.3 5.1
Order example:
B623C2E = ball bearing with PP cage and stainless steel balls
ESD protection
PA cage, PE cage,
stainless steel balls stainless steel balls
Temperature range Temperature range
-40°F to +176°F -40°F to +176°F
Dimensions [mm]
Part No. Inner Ø Outer Ø Width
Cage/ball material combination
d1 d2 b1 PA/E PE/E
B623F£E 3 10 4
B624F£E 4 13 5
B625F£E 5 16 5
B626F£E 6 19 6
B608F£E 8 22 7
B6000F£E 10 26 8
B6001F£E 12 28 8
B6002F£E 15 32 9
B6003F£E 17 35 10
B6004F£E 20 42 12
Order key
Dimensions acc.
Ball material
Cage material
Race material
E = stainless steel
to DIN 625-1
b1 b1
Ball material
Ball bearing
d2 d2
F180
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PA/E PE/E
[lbs] [lbs] [lbs] [rpm] [g] [g]
623 7 6 8 4,400 0.4 0.4
624 9 7 10 3,900 1.0 1.0
625 17 9 12 3,600 1.6 1.6
626 21 9 13 3,200 2.1 2.1
608 37 24 34 2,500 3.8 3.8
6000 64 28 31 2,100 5.9 5.9
6001 71 31 38 2,000 6.9 6.9
6002 76 33 44 1,800 8.9 8.9
6003 81 53 74 1,600 10.7 10.7
6004 90 55 72 1,400 13.4 13.4
Order example:
B623F1E = ball bearing with PA cage and stainless steel balls
Order key
Dimensions acc.
E = stainless steel
xirodur® M180 cage,
Cage material
Race material
to DIN 625-1
Ball material
Ball bearing
stainless steel balls
M180
Special designs made
from xirodur® M180
➤ Page 723
d1
d1
b1 b1
d2 d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 M180/E
B6000M4E 10 26 8
B6003M4E 17 35 10
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PP/E
[lbs] [lbs] [lbs] [rpm] [g]
6000 64 19 27 1,900 6.1
6003 81 40 56 1,400 11.1
Order example:
B6000M4E = ball bearing with M180 cage and stainless steel balls
Order key
Options
Type Size xirodur® Options
Cage material
B 6002 T 2 E 2 = PP
Ball material
Dimensions acc.
E = stainless steel
Cage material
Race material
PP cage,
to DIN 625-1
Ball material
Ball bearing
stainless steel balls
T220
d1
b1
d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 T220/E
B6002T2E 15 32 9
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PP/E
[lbs] [lbs] [lbs] [rpm] [g]
6002 76 33 44 1,600 8.9
Order example:
B6002T2E = ball bearing with PP cage and stainless steel balls
Order key
Dimensions acc.
E = stainless steel
PA cage,
Cage material
Race material
to DIN 625-1
Ball material
Ball bearing
stainless steel balls
B180
d1
d1
b1 b1
d2 d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 PA/E
B623D1E 3 10 4
B626D1E 6 19 6
B608D1E 8 22 7
B6000D1E 10 26 8
B6001D1E 12 28 8
B6002D1E 15 34 9
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PA/E
[lbs] [lbs] [lbs] [rpm] [g]
623 .22 .45 3 5,000 0.4
626 1 3 7 4,500 2.0
608 1.5 4 9 4,300 3.7
6000 2 6 8 4,200 5.7
6001 3 7 11 4,000 6.6
6002 3 10 11 3,870 8.5
Order example:
B623D1E = ball bearing with PA cage and stainless steel balls
Order key
Dimensions acc.
E = stainless steel
Cage material
Race material
PA cage,
to DIN 625-1
Ball material
Ball bearing
stainless steel balls
G220
d1
d1
b1 b1
d2 d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 G220/E
B6000G1E 15 32 9
Technical data
Order example:
B6000G1E = ball bearing with PA cage and stainless steel balls
Order key
Dimensions acc.
E = stainless steel
Cage material
Race material
PA cage,
to DIN 625-1
Ball material
Ball bearing
Double row
stainless steel balls
or glass balls
M180
Higher loads
Less expensive than two comparable bearings
A
d1
d2
A b1
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 PA/E PA/G
B6000B1EDR 10 26 14
B6004B1EDR 20 42 20
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic E G
[lbs] [lbs] [lbs] [rpm] [g] [g]
6000 180 36 51 850 11.0 7.0
6004 247 79 119 510 36.0 29.0
Order example:
B6000B1EDR = double row ball bearing with PA cage and stainless steel balls
Order key
Multi-axis bearings
Housing material
PP ball
Ball material
Outer-Ø (d2)
Ball bearing
Inner-Ø (d1)
Width (b)
For rotary and linear motions
A A
d1
d1
d2
d2
A A b b
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 B180/P
BMA163311BP 16.3 33 11
Technical data
Type Bearing load, radial Maximum speed Weight
static dynamic P
[N] [N] [rpm] [g]
BMA 12 16 500 6.9
Order example:
BMA163311BP = multi-axis ball bearing with B180 cage and PP balls
d2
d1
d3
xirodur® B180 races xirodur® B180 races b1
d2
d3
d1
xirodur® F180 races xirodur® F180 races
PA cage, stainless steel PA cage, stainless steel balls b1
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
B180 F180
d1 d2 d3 b1 b2 PA/E PA/G B180/E PA/E
BC608F£1£ 8 26 28 5.5 7
BC608FF£££ 8 26 28 4 7
B608F28B1E 8 28 30 5.5 7
B6000F28B1E 10 28 30 7 9
B6001F28B1E 12 28 30 7 9
B6000F35B1E 10 35 38 7 9
B6001F35B1E 12 35 38 7 9
B6002F35B1E 15 35 38 7 9
B6003F35B1E 17 35 38 8 10
Order example:
B6000F28B1E = B180 flange bearing with PA cage and stainless steel balls
Order key
Dimensions acc.
3 = xirodur® B180
Cage material
Race material
Ball material
to DIN 625-1
ball material
Ball bearing
E = stainless steel
With cover
G = glass
B180
d2
Technical data
Size Bearing load Maximum Weight
Flange on Maximum static speed B180 F180
both sides bearing load axial
static dynamic PA/E PA/G B180/E PA/E
[lbs] [lbs] [lbs] [rpm] [g] [g] [g] [g]
608 37 18 19 2,500 32.5 25.9 – 5.9
608 37 18 19 2,500 6.1 4.8 – 6.1
6000 64 19 27 1,900 9.6 – 9.6 –
6001 71 24 33 1,750 10.8 – – –
6002 76 33 44 1,600 12.1 – – –
6003 81 54 74 1,600 13.4 – 13.4 –
Order key
Ball material
Outer-Ø (d2)
E = stainless steel
Ball bearing
Inner-Ø (d1)
G = glass
Length
b1
d2
d3
d1
Dimensions [mm]
Part No. Inner Ø Outer Ø Flange Ø Length
d1 d2 d3 b1
BKA3008B1E £ 8 30 29.9 25 – 1,500
BKA3010B1E £ 10 30 29.9 25 – 1,500
BKA3012B1E £ 12 30 29.9 25 – 1,500
BKA3810B1E £ 10 38 37.9 25 – 1,500
BKA3812B1E £ 12 38 37.9 25 – 1,500
BKA3815B1E £ 15 38 37.9 25 – 1,500
BKA3817B1E £ 17 38 37.9 25 – 1,500
Order example:
BKA3010B1E, L=500 mm = aluminum tube with 2 flange ball bearings, PA cage and stainless steel balls,
total length 500 mm
Order key
Spherical outer Ø
Dimensions acc.
xirodur® B180 races xirodur® B180 races 1 = PA
Cage material
Race material
PA cage, PA cage, 4 = xirodur® M180
to DIN 625-1
Ball material
Ball bearing
stainless steel balls glass balls
Ball material
E = stainless steel
G = glass
d1
d2
xirodur® M180 races
xirodur® M180 cage,
stainless steel balls
A b1
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PA/E PA/G M180/E
[lbs] [lbs] [lbs] [rpm] [g] [g] [g]
608 37 13 19 2,200 4.8 3.5 –
6000 64 19 27 1,900 7.9 5.8 6.1
6001 71 24 33 1,750 13.5 11.1 –
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 b1 PA/ES PA/GL M180/ES
BSO608£££ 8 24 8
BSO6000£££ 10 28.96 10
BSO6001£££ 12 35.56 12
Order example:
BSO608B1E = ball bearing made from xirodur® B180, spherical outer diameter, PA cage and stainless steel
balls
Order key
Dimensions acc.
5 = PE
Cage material
PA cage,
Race material
Ball material
to DIN 625-1
Ball material
Outer-Ø (d2)
Ball bearing
stainless steel balls
E = stainless steel
or glass balls
End cap
G = glass
B180
PA cage,
d2
d3
d1
stainless steel balls
hex socket contour
b2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Cage/ball material combination
d1 d2 d3 b1 b2 PA/G PA/E
BEC620444.5B1£ 20 44.5 50 37 39
BEC6204M8B1E M8 44.5 50 38.5 39
Technical data
Size Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic PA/ES PA/GL
[lbs] [lbs] [lbs] [rpm] [g] [g]
6204 117 55 66 1,800 32.5 25.9
6204 117 55 66 1,800 33.0 –
Order example:
BB-6204EC44.5-B180-10-ES = end cap made from xirodur® B180, with PA cage and stainless steel balls
Order key
Dimensions acc.
E = stainless steel
Cage material
Race material
PA cage, G = glass
to DIN 625-1
Ball material
Skate wheel
Ball bearing
stainless steel balls
Outer-Ø
B180
PA cage,
glass balls
b1
d1
d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width
B6004SW100B1£ 20 100 12
Technical data
Size Bearing load Maximum speed Weight
static dynamic E G
[lbs] [lbs] [rpm] [g] [g]
6004 55 66 1,400 60.5 55.7
Order example:
BB-6004SW100-B180-10-ES = xiros® skate wheel with 100 mm outer diameter, races made from xirodur®
B180, PA cage and stainless steel balls
Order key
Race/cage material
Stainless steel balls Double row,
Dimensions acc.
or glass balls stainless steel balls
or glass balls
to DIN 625-1
Ball material
Ball bearing
Suitable for absorbing axial forces
B180
Axial
d3 A
A-A
h
d1 A
d2
Dimensions [mm]
Part No. Inner Ø Outer Ø Width Height Cage/ball material combination
d1 d2 d3 h B180/E B180/G
BA51100B£ 10 24 23.5 9
BA51104B£ 20 35 34.5 10
BA51104BED 20 47 46.5 10
Technical data
Size Double row Bearing load Maximum speed Weight
static dynamic E G
[lbs] [lbs] [rpm] [g] [g]
51100 45 56 600 6.9 4.4
51104 146 182 460 14.0 8.0
51104 219 273 460 28.0 17.0
Order example:
BB-51100-B180-ES = axial ball bearing with B180 cage and stainless steel balls
Order key
Options:
Type xirodur® Options
Ball material
B TW 6000 B E E = stainless steel
G = glass
Dimensions acc.
Stainless steel balls
Thrust washer
Cage material
to DIN 625-1
Ball material
Ball bearing
b1
b2
d1
B180
d2
Glass balls
d1 d2 b1 b1 B180/ES B180/GL
BTW626B£ 6.2 18.8 3.18 –
BTW608B£ 8.2 21.8 3.97 –
BTW6000B£ 10.2 25.8 4.76 3.97
BTW6000B£SL 10.2 25.8 3.97 –
BTW6004B£ 21 41 4.76 –
BTW6006B£ 29.9 45.5 4.76 3.97
BTW6006B£SL 29.9 45.5 4.76 –
Order example:
BB-6000TW-B180-ES-SL = thrust washer with stainless steel balls, slim line version
Order key
Material B180
Plastic ball transfer unit Plastic ball transfer unit
Ball Material
h2
Housing
h2
h1
Axial
h1
Size
d1
d1 d2 Dimensions [mm]
d2 BB-522-B180-POM
Part No. Size Inner Ø Height
BB-515-B180-POM
BB-505-B180-POM
d1 d2 h1 h2
BT505BPOM 505 10.4 12.0 8.4 4.3
BT515BPOM 515 24.0 31.0 21.0 9.8
BT522BPOM 522 36.0 45.0 30.0 9.8
Axial plastic ball transfer unit
BT515AB£ 515A 24.0 31.0 14.3 5.3
BT522AB£ 522A 36.0 45.0 21.25 7.05
Axial plastic ball transfer
Axial plastic ball transfer unit with soft roller made Technical data
unit for high loads (HH) from xirodur® D180 (HS)
Part No. Size Maximum static Weight
bearing load axial
Axial plastic unit: [g]
h2
[lbs]
B180 = HH (hard roller)
h1
Dimensions [mm]
Part No. For ball transfer unit d1 d2 Housing bore
BB-515-CR BB-515-B180-POM/BB-515A-B180-£ 24 31 25.0 –0.2
BB-522-CR BB-522-B180-POM/BB-522A-B180-£ 36 41 37.3 –0.3
Order key
Ball material
Slewing ring
Standard version Standard version
Ball bearing
with stainless with Glass balls
bearing
Inner-Ø
steel balls
A
T
D
A
68
n
2
0,7
n
10
d
°
60
k2
n90
60
h
k1
A
H
d1
D1 HDT5 version n2
,9
Standard version Stainless steel 2,5
A 17,5
balls, with gear
teeth Version with gear teeth
Dimensions [mm]
Part No. D D1 d d1 H h T K1 K2
BRT60£ 100 90.0 60 68 17.5 2.5 60 3.3 3.3
BRT100£ 160 150.0 100 110 20 5 60 5.2 5.2
With gear teeth
BRT60HDT5E 100 90.0 60 68 17.5 2.5 60 3.3 3.3
Technical data
Type Bearing load Maximum speed Weight
static dynamic E G
[lbs] [lbs] [rpm] [g] [g]
BRT60£ 180 225 250 111.9 98.3
BRT100£ 281 337 250 250.8 231.1
With gear teeth
BRT60HDT5E 180 225 860 110.0 –
Order example:
BRT60E = slewing ring bearing with stainless steel balls
Order key
Type Options
Options
Race material
ESTM 1 F 06 B E B = xirodur® B180
Ball material
E = stainless steel
Race material
igumid G housing, igumid G housing, G = glass
Fixed version
Ball material
Ball bearing
PA cage, stainless steel balls PA cage, glass balls
Single row
Inner-Ø
Suitable for wash-down and non-magnetic
h
h1
a
d3
C1
B
h2
d1
m
d1
m
h
h1
R1
B
R1
d2
C1
Dimensions [mm]
d3
d2
Technical data
h2
Order example:
ESTM1F06BE = pillow block bearing, fixed version, made from xirodur® B180 with stainless steel balls
Order key
Type Options
Options
Race material
ESTM 1 P 08 B E B = xirodur® B180
Ball material
Pivoting version
E = stainless steel
Race material
igumid G housing, igumid G housing, G = glass
Ball material
Ball bearing
PA cage, stainless steel balls PA cage, Glass balls
Single row
Inner-Ø
Compensation of misalignment errors
h
C1
a h1
d3 B
C1
B
h2
d1
m
d1
m
h
h1
R1
R1
d2
Dimensions [mm]
d3
d2
Technical data h2
Order example:
ESTM1P08BE = pillow block bearing, pivoting version, made from xirodur® B180 with stainless steel balls
Order key
Type Options
Options
Race material
ESFM 1 P 08 B E B = xirodur® B180
Ball material
E = stainless steel
Race material
igumid G housing, G = glass
Fixed version
Ball material
Ball bearing
PA cage, stainless
Single row
steel or glass balls
Inner-Ø
Compensation of misalignment errors
L L
J J
B
C
C
dB
dB
d1
d1
L
J
L
J
A1
C
C
N (4x
N (4x
Ag
)
)
Dimensions [mm]
Part No. Inner Ø dB L J A1 Ag B N Maximum pivot
d1 d2 angle
Technical data
Type Maximum static Bearing load Maximum speed Weight
bearing load axial static dynamic E G
[N] [N] [N] [rpm] [g] [g]
EFSM-P08 37 13 19 2,200 25.2 24.0
EFSM-P10 64 19 27 1,900 48.8 46.2
EFSM-P12 71 24 33 1,750 80.0 77.7
Order example:
EFSM1P08BE = 4-hole flange bearing made from xirodur® B180 with stainless steel balls
Order key
Type Options
Options
Race material
ESFM 1 P 08 B E B = xirodur® B180
Ball material
E = stainless steel
Race material
igumid G housing, G = glass
Fixed version
Ball material
Ball bearing
PA cage, stainless steel
Single row
or glass balls
Inner-Ø
L
N
Trouble free readjustment thanks to extended holes
Precise alignment of the bearings not necessary
H
dB
d1
B
Ag
L
N
A1
H
dB
d1
Dimensions [mm]
B
Ag
A1
Technical data
Order example:
EFOM1P08BE = 2-hole flange bearing made from xirodur® B180 with stainless steel balls
..
...plastics
Application Examples - igubal®
LIMELIGHT BV
Stadium paneling igubal® spherical bearings of atmospheric resistance. Since these slats can be
dimension K series are used in the main bearing swiveled, this allows the air flow inside the stadium to
assembly of every individual slat due to their freedom be regulated. Part number: igubal® spherical bearing
from maintenance, corrosion resistance and KGLM-08
Angled and
in-line joints Angled ball and socket Angled ball and socket Easy assembly In-line ball and socket
joint joint, low-cost and disassembly joint
WGRM/WGLM WGRM-LC/WGLM-LC WGRM-DE/WGLM-DE AGRM/AGLM
igubal® clevis joints – Weight reduction, very simple assembly with E series rod ends
Clevis joint
combinations Clevis joint, pin and Clevis joints with clevis Clevis joints with spring- Combination,
circlip inch dimensions pin and circlip loaded fixing clip easy to fit
GERIK/GELIK GERMK/GELMK GERMF/GELMF GERMKE/GELMKE
igubal® pillow block bearings – Cost-effective, maintenance free, for high radial loads
For temperatures up to
+392 °F
EARM-HT/EALM-HT
➤ Page 776
Component
Combination, parts Clevis joint Clevis joint Spring-loaded Clevis pin and
inch dimensions fixing clip Circlip
easy to fit
GERI/GELI GERM/GELM GEFM GBM/GSR
GERMFE/GELMFE
➤ Page 799 ➤ Page 790 ➤ Page 792 ➤ Page 796 ➤ Page 800
➤ Page 814 ➤ Page 815 ➤ Page 806 ➤ Page 808 ➤ Page 816
For temperatures
up to +176 °F Easy to install For higher radial load Universal and Universal and
EFOI - inch ➤ 822 EFSI - inch ➤ 826 quick assembly quick assembly
EFOM - metric ➤ 824 EFSM - metric ➤ 828 GFSM-IG GFSM-AG
Pressfit spherical
bearings Standard, easy to fit, Standard, For extremely narrow For extremely narrow
inch dimensions easy to fit installation space installation space
KGLI KGLM KGLI-SL KGLM-SL
➤ Page 840 ➤ Page 841 ➤ Page 842 ➤ Page 843
Self-aligning
Simply snapping For high axial and radial For tolerance
clip bearing into sheet metal loads, selectable ball compensation, selectable
ECLM material ball material
ECLM-HD EGFM-T
Different ball
materials Standard, with low wear Low-cost, good wear For temperatures Low moisture absorption
WKI/WEI resistance up to +482 °F JKM/JEM
WKM/WEM RKM/REI/REM XKM/XEM
Double joints Solid polymer, Variety of ball and tube materials, ball stud and tube,
ball material options individual dimensions and alignment individual dimensions and alignment
EGZM KDGM WDGM
Low-cost and low For underwater Clearance free Detectable For metallic bearing
moisture absorption applications RN248KM/ housings
J4KM/J4EM UWEM J4VEM RN248EM
➤ Page 867 ➤ Page 868 ➤ Page 869 ➤ Page 870 ➤ Page 871
igubal® – self-aligning maintenance free plain bearings made of high performance polymers
igubal® puts a complete system of self-aligning bearings – spherical iglide® T500 (X)* for high temperatures
bearings, pillow block spherical bearings and rod ends – at the iglide® J for low moisture absorption
developer’s fingertips. Self-aligning bearings are easy to fit, adapt to iglide® J4 for low moisture absorption at lower costs
all angular deviations and replace special housings in many cases. iglide® R as a low-cost alternative
With igubal , the user can take advantage of all the benefits of
®
iglide® UW for under water applications
high performance plastics: vibration dampening, ability to operate iglide® RN248 as detectable material
in liquids or chemicals, and resistance to dirt and dust, which can iglide® J4 with clearance free spherical balls
impede the performance of greased metal components. ➤ Spherical balls ➤ Page 857
The weight of the igubal parts is approx. 80% lighter than
®
comparable steel parts. Additional savings are cost-savings at Do not hesitate to ask for technical support concerning the choice
the time of purchasing and during operation and on installation of the material. Please contact igus®.
space due to their small dimensions. igubal bearings are also
®
100
Thread description Pitch [mm]
90
M2 0.40
Percentage tensile strength [%]
80 M3 0.50
70 M4 0.70
60 M5 0.80
50 M6 1.00
40
M8 1.25
M10 1.50
30
M10 F 1.25
20
M12 1.75
68 104 140 176 212 248 284 320 356 392
Temperature [ºF]
M12 F 1.25
Standard temperatures materials M14 2.00
High temperatures material
M16 2.00
Diagram 01: trends indicate the effect of temperature on the maximum M16 F 1.50
load capacity of igubal® bearings. M18 1.50
M20 1.50
M20 M20 2.50
Coefficients of sliding friction and speed M22 1.50
One important advantage of igubal® spherical bearings is that M24 2.00
rapid, rotary movements of a mounted shaft take place directly M27 2.00
in the spherical portion, made of iglide® L280 (W300)*. In metallic M30 2.00
rod ends, rotary motion takes place between the race and the Table 02: Thread pitches of igubal® rod ends and clevis joints
Radiation resistance
Self-aligning igubal® plain bearings are resistant to radiation up to Tolerance test with gauge
an intensity of 3 · 102 Gy.
value for outside applications. igubal® bearings are permanently for every application. You can choose from different igubal® bearings
resistant to UV radiation. A small change in color (dark coloration) and specific load (radial, axial or static, cyclic and dynamic). The
of the spherical ball due to UV radiation does not affect the mech expert system will calculate from these input data:
Tolerances
igubal® spherical bearings can be used with different tolerances
according to each application. They are designed with a large
clearance in the standard product, which enables a secure
operation even under high peripheral speeds. The inside diameter
of the spherical ball has a tolerance of E10. The shafts should have
tolerances between h6 and h9. The tolerances are provided in the
table below. Please contact us in case you require lower or other
bearing tolerances.
igubal® rod ends can also be used in rough environments. They are corrosion-resistant in humid environments and resistant to
weak acids and bases. The operation temperature is from –40°F up to +176°C. Rod ends are also resistant to dirt and dust.
Maintenance free,
dry-running
When to use it?
If you want to save weight
For rotating, oscillating and linear movements
High strength If high-frequency oscillations/vibrations occur
under impact loads If silent operation is required
If you need an electrically insulating part
If corrosion resistance is required
In combination with pneumatic cylinders and gas struts
High tensile strength If chemical resistance is required
If high rigidity is required
Compensation of misalignment
Ø 3/16 to 1 inch
18 types
mm Ø 2 to 30 mm
Loads 105
directly in the inner diameter of the spherical portion. The Temperature (°F)
advantage, therefore, lies in the plastic vs. steel relationship.
Plastic produces lower friction and permits high speeds, even Effect of the temperature on the maximum tensile
when running dry. strength of igubal® rod end bearings
The maintenance-free igubal® bearing system is also suited for
linear and oscillating shaft movements.
Temperatures
Tolerances
igubal ® rod end bearings can be used at different tolerances depending on the individual application. As a standard program,
they are designed with a large amount of bearing clearance, which permits secure operation even at high rotational speeds. The
bore of the inner race is produced within a standard tolerance range. Shafts should also meet recommended tolerances. Please
contact us with any questions regarding tolerances.
Recommended Shaft Tolerances Thread pitches of the igubal® rod end bearings
Inch Shaft Metric Shaft Thread Name Pitch (mm)
Min. Max. Min. Max. M2 0.40
3/16 0.1888 0.1900 2mm 1.975 2.000 M3 0.50
1/4 0.2485 0.2500 3mm 2.975 3.000 M4 0.70
5/16 0.3110 0.3125 5mm 4.970 5.000 M5 0.80
3/8 0.3735 0.3750 6mm 5.970 6.000 M6 1.00
7/16 0.4358 0.4375 8mm 7.964 8.000 M8 1.25
1/2 0.4983 0.5000 10mm 9.964 10.000 M 10 1.50
5/8 0.6235 0.6250 12mm 11.957 12.000 M 10 F 1.25
3/4 0.7479 0.7500 16mm 15.957 16.000 M 12 1.75
1 0.9980 1.0000 20mm 19.948 20.000 M 12 F 1.25
M 14 2.00
M 16 2.00
M 16 F 1.50
M 18 1.50
M 20 2.50
M 20 M 20 1.50
M 22 1.50
M 24 2.00
M 27 2.00
M 30 2.00
Classic design For small space Classic design Integrated lock nut for Ball material options
requirement, ball material easy assembly,
options, inch dimensions ball material options
K series E series K series K series K series
KBRI EBRI/EBLI KBRM KBRM CL KCRM
KBLI KBLM KBLM CL KCLM
➤ Page 754 ➤ Page 756 ➤ Page 758 ➤ Page 760 ➤ Page 762
Classic design Classic design For higher forces, For small space For temperatures
inch dimensions ball material options requirement, up to +392 °F
K series K series K series ball material options E series
KARI KARM KARM CL E series EARM HT
KALI KALM EARM/EALM EALM HT
➤ Page 768 ➤ Page 770 ➤ Page 772 ➤ Page 774 ➤ Page 776
Angled ball and Angled ball and Easy assembly In-line ball and In-line ball and
socket joint socket joint, and disassembly socket joint socket joint,
low-cost low-cost
WGRM WGRM-LC WGRM-DE AGRM AGRM-LC
WGLM WGLM-LC WGLM-DE AGLM AGLM-LC
➤ Page 779 ➤ Page 780 ➤ Page 781 ➤ Page 782 ➤ Page 783
Adapter bolt Clevis joints with clevis Clevis joints Clevis joints with spring-loaded
pin and circlip with clevis pin fixing clip
K series Inch dimensions and circlip E series
PKRM E series E series GERMF/GELMF
PKLM GERIK/GELIK GERMK/GELMK
Dimensions [inch]
Part No. Part No. d1 d2 d3 d4 C1 B h1 l1 l2 W
Max. pivot
Right thread Left thread [E10] angle
KBRI-03 KBLI-03 .1875 .625 10-32 .406 .246 .312 1.062 .500 1.374 .312 25°
KBRI-04 KBLI-04 .2500 .750 1/4-28 .469 .272 .365 1.312 .687 1.687 .375 25°
KBRI-05 KBLI-05 .3125 .875 5/16-24 .500 .340 .437 1.375 .687 1.813 .437 25°
KBRI-06 KBLI-06 .3750 1.00 3/8-24 .687 .394 .500 1.625 .812 2.125 .562 22°
KBRI-07 KBLI-07 .4375 1.125 7/16-20 .750 .456 .562 1.812 .937 2.374 .625 22°
KBRI-08 KBLI-08 .5000 1.312 1/2-20 .875 .487 .625 2.125 1.062 2.781 .750 22°
KBRI-10 KBLI-10 .6250 1.50 5/8-18 1.00 .545 .750 2.50 1.375 3.25 .875 22°
KBRI-12 KBLI-12 .7500 1.75 3/4-16 1.125 .676 .875 2.875 1.562 3.75 1.00 22°
KBRI-16 KBLI-16 1.00 2.75 1-12 1.625 1.00 1.375 4.125 2.125 5.50 1.50018) 20°
B Order key
d2 C1
Type Size
K B ... I - 08
d1
Based on 1/16”
Inner-Ø [inch]
l1
Thread
d3
Inch
d4
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Right thread Left thread Short term Long term Short term Long term Inner thread
[lbs] [lbs] [lbs] [lbs] (inch) (ft•lbs) (ft•lbs) [g]
Dimensions [inch]
Part No. Part No. d1 d2 d3 d4 d5 C1 B h1 l3 l4 W Max.
pivot
Right thread Left thread [E10]
angle
EBRI-03 EBLI-03 0.1900 0.748 10-32 0.3543 0.4331 0.1732 0.1900 1.1811 0.4724 1.5551 0.35 30°
EBRI-04 EBLI-04 0.2500 0.827 1/4-28 0.4331 0.5118 0.1732 0.2500 1.1811 0.4724 1.5945 0.43 25°
EBRI-05 EBLI-05 0.3125 0.945 5/16-24 0.5118 0.6299 0.2362 0.3125 1.4173 0.6299 1.8898 0.55 22°
EBRI-06 EBLI-06 0.3750 1.142 3/8-24 0.5906 0.7480 0.2756 0.3750 1.6929 0.7087 2.2638 0.67 22°
EBRI-07 EBLI-07 0.4375 1.339 7/16-20 0.7087 0.8661 0.3150 0.4063 1.9685 0.7874 2.6378 0.75 18°
EBRI-08 EBLI-08 0.5000 1.339 1/2-20 0.7087 0.8661 0.3150 0.4063 1.9685 0.7874 2.6378 0.75 18°
EBRI-10 17)
EBLI-10 17)
0.6250 1.693 5/8-18 0.8270 1.0230 0.4134 0.5000 2.5394 1.0433 3.3858 0.87 16°
EBRI-12 EBLI-12 0.7500 2.087 3/4-16 1.0630 1.3386 0.5118 0.6250 3.0315 1.2205 4.0748 1.18 14°
For another spherical bearing material please add J, J4, or R to the part number, Example: EBRI-08R.
17)
EBRI-10/EBLI-10 special design with hexagonal foot
➤ Tolerance Table, Page 75
E B ... I - 08
d1
Dimensional E series
Based on 1/16”
Inner-Ø [inch]
l1
Thread
d3
Inch
d4
W
d5
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Strength through ball
Right thread Left thread Short term Long term Short term Long term Depth Outer thread
[lbs] [lbs] [lbs] [lbs] (inch) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 d4 d5 C1 B h1 L3 L4 W Max.
without with MH pivot
Right thread Left thread [E10]
MH ±0.2 angle
KBRM-02 KBLM-02 2 9 M02 4.0 4.6 3.0 4 4.1 12.5 6 17 SW04 30°
KBRM-03 KBLM-03 3 13 M03 6.5 8.0 4.5 6 6.1 18.5 8 25 SW07 30°
KBRM-05 M4 KBLM-05 M4 5 18 M04 9.0 12.0 6.0 8 8.1 27 10 36 SW09 30°
KBRM-05 KBLM-05 5 18 M05 9.0 12.0 6.0 8 8.1 27 10 36 SW09 30°
KBRM-06 KBLM-06 6 20 M06 10.0 13.0 7.0 9 9.2 30 12 40 SW11 29°
KBRM-08 KBLM-08 8 24 M08 13.0 16.0 9.0 12 12.2 36 16 48 SW14 25°
KBRM-10 KBLM-10 10 30 M10 15.0 19.0 10.5 14 14.2 43 20 58 SW17 25°
KBRM-10 F KBLM-10 F 10 30 M10 x 1.25 15.0 19.0 10.5 14 14.2 43 20 58 SW17 25°
KBRM-12 KBLM-12 12 34 M12 18.0 22.0 12.0 16 16.2 50 22 67 SW19 25°
KBRM-12 F KBLM-12 F 12 34 M12 x 1.25 18.0 22.0 12.0 16 16.2 50 22 67 SW19 25°
KBRM-14 KBLM-14 14 38 M14 20.0 25.0 13.5 19 19.2 57 25 76 SW22 23°
KBRM-16 KBLM-16 16 42 M16 22.0 27.0 15.0 21 21.2 64 28 85 SW22 23°
KBRM-16 F KBLM-16 F 16 42 M16 x 1.5 22.0 27.0 15.0 21 21.2 64 28 85 SW22 23°
KBRM-18 KBLM-18 18 46 M18 x 1.5 25.0 31.0 16.5 23 23.2 71 32 94 SW27 23°
KBRM-20 KBLM-20 20 50 M20 x 2.5 28.0 34.0 18.0 25 25.3 77 33 102 SW30 23°
KBRM-20 M20 KBLM-20 M20 20 50 M20 x 1.5 28.0 34.0 18.0 25 25.3 77 33 102 SW30 23°
KBRM-22 KBLM-22 22 56 M22 x 1.5 30.0 37.0 20.0 28 – 84 37 112 SW32 22°
KBRM-25 KBLM-25 25 60 M24 x 2.0 32.0 41.0 22.0 31 – 94 42 124 SW36 22°
KBRM-30 KBLM-30 30 70 M30 x 2.0 37.0 50.0 25.0 37 – 110 51 145 SW41 22°
KBRM-30 M27x2 KBLM-30 M27x2 30 70 M27 x 2.0 37.0 50.0 25.0 37 – 110 50 145 SW41 22°
Rod end bearings can be ordered in metric dimensions with metal sleeve with the addition of MH after the part numbers listed here
Example: KBRM-10 MH
Type Size
K B ... M - 02
d1
Dimensional K series
Inner-Ø [mm]
I1
d3
Thread
Metric
d4
d5 W
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Right thread Left thread Short term Long term Short term Long term Inner thread without MH with MH
[lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. d1 d2 d3 d4 B C1 h h1 h2 L2 L1
Max. pivot
[E10] angle
K B R M - 06 CL
d1
h3
Dimensional K series
h1
2nd generation
Inner-Ø [mm]
m
d3
Metric
W
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Short term Long term Short term Long term outer thread without MH with MH
[lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) (ft•lbs) [g]
For rod end bearings with metal sleeve please add MH to the part number. Example: KBRM-10 CL MH (Inner-Ø: 10 mm).
For another spherical bearing material please add J, J4, or R to the part number, Example: KBRM-10 CL J.
Dimensions [mm]
Part No. Part No. d1 d2 d3 W B C1 h1 L3 L4
Max. pivot
without with MH
Right thread Left thread [E10] angle
MH ±0.2
KCRM-05 KCLM-05 05 18 M5 SW9 8.0 8.2 6.0 27 12 36 43°
KCRM-06 KCLM-06 6 20 M06 SW10 9.0 9.2 7 30 13.5 40 40°
KCRM-08 KCLM-08 8 24 M08 SW13 12.0 12.2 9 36 17 48 35°
KCRM-10 KCLM-10 10 30 M10 SW15 14.0 14.2 10,5 43 22 58 35°
KCRM-10-F KCLM-10-F 10 30 M10x1.25 SW15 14.0 14.2 10.5 43 22 58 35°
KCRM-12 KCLM-12 12 34 M12 SW17 16.0 16.2 12.0 50 25 67 35°
KCRM-12-F KCLM-12-F 12 34 M12x1.25 SW17 16.0 16.2 12.0 50 25 67 35°
KCRM-16 KCLM-16 16 42 M16 SW20 21.0 21.2 15.0 64 30 85 35°
KCRM-16-F KCLM-16-F 16 42 M16x1.5 SW20 21.0 21.2 15.0 64 30 85 35°
KCRM-20 KCLM-20 20 50 M20x1.5 SW24 25.0 25.2 18.0 77 35 102 35°
KCRM-20-M20 KCLM-20-M20 20 50 M20x2.5 SW24 25.0 25.2 18.0 77 35 102 35°
Type Size
K C ... M - 06
d1
Dimensional K series
Inner-Ø [mm]
l1
Thread
d3
Metric
W
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Part No. Maximum static Maximum Static Max. torque Max. torque Weight
tensile strength radial load strength through Ball
Short term Long term Short term Long term Inner thread without MH with MH
Right thread Left thread [lbs] [lbs] [lbs] [lbs] (ft•lbs) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 d4 d5 C1 B h1 l3 l4 W
Max. pivot
Right thread Left thread [E10] angle
EBRM-04 EBLM-04 4 15 M04 8.0 9.2 3.5 5 22.5 9.5 30.0 SW08 33°
EBRM-05 EBLM-05 5 19 M05 9.0 11 4.4 6 30 12 39.5 SW09 33°
EBRM-06 EBLM-06 6 21 M06 11.0 13 4.4 6 30 12 40.5 SW11 27°
EBRM-08 EBLM-08 8 24 M08 13.0 16 6.0 8 36 16 48.0 SW14 24°
EBRM-10 EBLM-10 10 29 M10 15.0 19 7.0 9 43 18 57.5 SW17 24°
EBRM-10 F EBLM-10 F 10 29 M10 x 1.25 15.0 19 7.0 9 43 18 57.5 SW17 24°
EBRM-12 EBLM-12 12 34 M12 18.0 22 8.0 10 50 20 67.0 SW19 21°
EBRM-12 F EBLM-12 F 12 34 M12 x 1.25 18.0 22 8.0 10 50 20 67.0 SW19 21°
EBRM-15 EBLM-15 15 40 M14 21.0 26 10.0 12 61 26 81.0 SW22 21°
EBRM-16 EBLM-16 16 43 M16 x 1.5 - - 10.5 13 64.5 26.5 86.0 SW22 21°
EBRM-16 F EBLM-16 F 16 46 M20 x 1.5 - - 10.5 13 64.5 26.5 86.0 SW22 21°
EBRM-17 EBLM-17 17 46 M16 24.0 30 11.0 14 67 27 90.0 SW27 21°
EBRM-17 F EBLM-17 F 17 46 M16 x 1.5 24.0 30 11.0 14 67 27 90.0 SW27 18°
EBRM-20 EBLM-20 20 53 M20 x 1.5 27.0 34 13.0 16 77 31 103.5 SW30 16°
EBRM-20 M20 EBLM-20 M20 20 53 M20 x 2.5 27.0 34 13.0 16 77 31 103.5 SW30 16°
B Order key
d2 C1
Type Size
E B ... M - 02
d1
Dimensional E series
Inner-Ø [mm]
l1
Thread
d3
Metric
d4
W
d5
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Right thread Left thread Short term Long term Short term Long term Inner thread Standard
[lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 d4 d5 C1 B h1 l3 l4 W
Max. pivot
Right thread Left thread [E10] angle
E B ... M - 06 HT
d1
l2
High temperature
l1
Inner-Ø [mm]
d3
d4
Thread
W
Metric
d5
Material:
Housing - iguton G ➤ Page 1373
Spherical ball - iglide® T500 (X)*
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Right thread Left thread Short term Long term Short term Long term Inner thread Standard
[lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) [g]
Dimensions [inch]
Part No. Part No. d1 d2 d3 C1 B h L1 L2 Max. pivot
Right thread Left thread [E10] angle
KARI-03 KALI-03 .1875 .625 10-32 .234 .312 1.250 .750 1.563 25°
KARI-04 KALI-04 .2500 .750 1/4-28 .250 .365 1.562 1.000 1.937 25°
KARI-05 KALI-05 .3125 .875 5/16-24 .312 .437 1.875 1.250 2.313 25°
KARI-06 KALI-06 .3750 1.000 3/8-24 .359 .500 1.938 1.250 2.438 22°
KARI-07 KALI-07 .4375 1.125 7/16-20 .406 .562 2.125 1.375 2.688 22°
KARI-08 KALI-08 .5000 1.312 1/2-20 .453 .625 2.428 1.500 3.094 22°
KARI-10 KALI-10 .6250 1.500 5/8-18 .484 .750 2.625 1.625 3.375 22°
KARI-12 KALI-12 .7500 1.750 3/4-16 .593 .875 2.875 1.750 3.750 22°
Type Size
K A ... I - 08
d1
Dimensional K series
Based on 1/16”
Inner-Ø [inch]
l1
Thread
Inch
d3
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Technical data
Part No. Part No. Max. static Max. Min. Max. Torque Max. Torque Strength Weight
Tensile Strength Radial Load Thread Depth Strength through ball
Right thread Left thread Short term Long term Short term Long term Outer thread
[lbs] [lbs] [lbs] [lbs] (inch) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 C1 B h1 l1 l2
Max. pivot
without with MH
Right thread Left thread [E10] angle
MH ±0.2
KARM-05 KALM-05 05 18 M05 6.0 8 8.2 33 19 42 30°
KARM-06 KALM-06 06 20 M06 7.0 9 9.2 36 21 46 29°
KARM-08 KALM-08 08 24 M08 9.0 12 12.2 42 25 55 25°
KARM-10 KALM-10 10 30 M10 10.5 14 14.2 48 28 63 25°
KARM-10 F KALM-10 F 10 30 M10 x 1.25 10.5 14 14.2 48 28 63 25°
KARM-12 KALM-12 12 34 M12 12.0 16 16.2 54 32 71 25°
KARM-12 F KALM-12 F 12 34 M12 x 1.25 12.0 16 16.2 54 32 71 25°
KARM-14 KALM-14 14 38 M14 13.5 19 19.2 61 36 79 25°
KARM-16 KALM-16 16 42 M16 15.0 21 21.2 66 37 88 23°
KARM-16 F KALM-16 F 16 42 M16 x 1.5 15.0 21 21.2 66 37 88 23°
KARM-18 KALM-18 18 46 M18 x 1.5 16.5 23 23.2 72 41 96 23°
KARM-20 KALM-20 20 50 M20 x 1.5 18.0 25 25.2 78 45 104 23°
KARM-20 M20 KALM-20 M20 20 50 M20 x 2.5 18.0 25 25.2 78 45 104 23°
KARM-22 KALM-22 22 56 M22 x 1.5 20.0 28 – 84 48 112 22°
KARM-25 KALM-25 25 61 M24 x 2.0 22.0 31 – 95 55 126 22°
KARM-30 KALM-30 30 71 M30 x 2.0 25.0 37 – 112 66 147 22°
Type Size
K A ... M - 08
d1
I2
I1
Inner-Ø [mm]
Thread
Metric
d3
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
Technical data
Part No. Part No. Maximum static Maximum Static Max. torque Max. torque Weight
tensile strength radial load strength through Ball
Short term Long term Short term Long term Outer thread without MH with MH
Right thread Left thread [lbs] [lbs] [lbs] [lbs] (ft•lbs) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. d1 d2 d3 C1 B h1 l1 l2
Max. pivot
without with MH
Right thread [E10] angle
MH ±0.2
KARM-06 CL 06 20 M06 7.0 9.0 9.2 36 21 46 40 °
KARM-08 CL 08 24 M08 9.0 12.0 12.2 42 25 55 35 °
KARM-10 CL 10 30 M10 10.5 14.0 14.2 48 28 63 35 °
KARM-12 CL 12 34 M12 12.0 16.0 16.2 54 32 71 35 °
For rod end bearings with metal sleeve please add MH to the part number, e.g. KABM-10 CL MH.
For another spherical bearing material please add J, or R to the part number, e.g. KARM-10 CL J.
➤ Tolerance Table, Page 75
K A R M - 06 CL
d1
Dimensional K series
h1
2nd generation
I1
Inner-Ø [mm]
Metric
d3
Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Maximum static Maximum Static Min. Max. torque Max. torque Weight
tensile strength radial load Thread Depth strength through Ball
Short term Long term Short term Long term Outer thread without MH with MH
Right thread [lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 C1 B h1 l1 l2
Max. pivot
Right thread Left thread [E10] angle
B Order key
d2 C1
Type Size
E A R M - 06
d1
Inner-Ø [mm]
I1
Metric
d3 Material:
Housing - igumid G ➤ Page 1373
Spherical ball - iglide® L280 (W300)*
Available with metal sleeve
More spherical ball materials available on
request ➤ Page 857
Technical data
Part No. Part No. Maximum static Maximum Static Min. Max. torque Max. torque Weight
tensile strength radial load Thread strength through Ball
Short term Long term Short term Long term Depth Outer thread
Right thread Left thread [lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) [g]
Dimensions [mm]
Part No. Part No. d1 d2 d3 C1 B h1 l1 l2
Max. pivot
Right thread Left thread [E10] angle
E A R M - 06 HT
d1
Dimensional K series
h1
High temperature
I1
Inner-Ø [mm]
Metric
d3
Material:
Housing - iguton G ➤ Page 1373
Spherical ball - iglide® T500 (X)*
Technical data
Part No. Part No. Maximum static Maximum Static Min. Max. torque Max. torque Weight
tensile strength radial load Thread strength through Ball
Short term Long term Short term Long term Depth Outer thread
Right thread Left thread [lbs] [lbs] [lbs] [lbs] (mm) (ft•lbs) (ft•lbs) [g]
I1
I2
Rod end accessories: Adapter bolt PKRM and PKLM
I3
d1
Order key
d3
Type Size
P K ... M - 08
I4
I1
w
I2
Inner-Ø [mm]
d3
Adapter bolt
Thread
Metric
Solid plastic bolts with a hexagonal head are an accessory to the K series rod ends. The
plain shank fits into the inside diameter of the spherical ball and is secured by a circlip. The
w
igubal® adapter bolts consist of highly shock-resistant, long-fiber reinforced polymer POM.
This component effectively transforms a standard K series rod end into a ball and socket joint.
Dimensions [mm]
Part No. Part No. d1 d3 l1 l2 l3 l4 SW
Connection Total Length Nut Thread Length Length Width across
h11 thread Width Adjusting Bolt Flats
Right thread Left thread (mm) (mm) (mm) (mm) (mm)
Technical data
Part No. Part No. Max. Static Tensile Strength Max. Static Radial Load Weight
Short term Long term Short term Long term
Right thread Left thread [lbs] [lbs] [lbs] [lbs] [g]
Vibration-dampening
WG ... M - 05 MS
Resistant to dirt and dust
Ball stud made of plastic or metal19)
Metal stud
d4
Thread
Metric
S1
Material:
b Ø d1 l5 Housing - igumid G ➤ Page 1373
a e Spherical cap - iglide® L280 (W300)*
h1
S1
d2
h2
I1
h3
I2
I6
d2
S2
Dimensions [mm]
Part No. Part No. d1 d2 d4 l1 l2 l5 l6 h1 h2 h3 a b e S1 Max.
Right thread Left thread ±0.1 ±0.5 ±0.2 ±0.3 min. ±0.4 ±0.5 ±05 ±0.3 ±0.5 ±0.5 pivot
angle
WGRM-05 WGLM-05 8.0 M5 12.8 9.0 10.2 14.0 8.2 10.8 0.65 25.6 22.0 28.4 11.0 SW 8 25°
WGRM-06 WGLM-06 10.0 M6 14.8 11.0 12.5 16.0 10.5 12.3 0.70 30.9 25.0 32.4 13.0 SW 9 25°
WGRM-08 WGLM-08 13.0 M8 19.3 13.0 16.5 18.0 13.5 16.2 1.15 38.8 30.0 39.7 16.0 SW 12 25°
WGRM-10 WGLM-10 16.0 M10 24.0 16.0 20.0 20.0 16.0 20.0 1.15 47.0 35.0 47.0 18.0 SW 14 25°
Technical data
Part No. Max. axial max. axial max. axial Max. axial tensile force Weight
tensile force compressive force tensile force
Right thread Left thread ball stud axis ball stud axis housing axis in housing axis with
metal ball stud
Short term Long term Short term Long term Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [g]
WGRM-05 WGLM-05 7 3 45 22 22 11 135 67 2.6
WGRM-06 WGLM-06 8 4 67 34 31 16 180 90 4.0
WGRM-08 WGLM-08 56 28 112 56 45 22 337 169 8.2
WGRM-10 WGLM-10 56 28 202 101 90 45 427 214 13.8
Inner-Ø [mm]
Low cost
d4
Thread
Metric
S1
Material:
b Ø d1 l5
Housing - igumid G ➤ Page 1373
a e
h1
S1
d2
h2
I1
h3
I2
I6
d2
S2
Dimensions [mm]
Part No. Part No. d1 d2 d4 l1 l2 l5 l6 h1 h2 h3 a b e S1 Max.
Right thread Left thread ±0.1 ±0.5 ±0.2 ±0.3 min. ±0.4 ±0.5 ±05 ±0.3 ±0.5 ±0.5 pivot
angle
WGRM-05 LC WGLM-05 LC 8.0 M5 12.8 9.0 10.2 14.0 8.2 10.8 0.65 25.6 22.0 28.4 11.0 SW 8 25°
WGRM-06 LC WGLM-06 LC 10.0 M6 14.8 11.0 12.5 16.0 10.5 12.3 0.70 30.9 25.0 32.4 13.0 SW 9 25°
WGRM-08 LC WGLM-08 LC 13.0 M8 19.3 13.0 16.5 18.0 13.5 16.2 1.15 38.8 30.0 39.7 16.0 SW 12 25°
WGRM-10 LC WGLM-10 LC 16.0 M10 24.0 16.0 20.0 20.0 16.0 20.0 1.15 47.0 35.0 47.0 18.0 SW 14 25°
19)
Metal stud option: MS = metal stud, only available with right-hand thread. Example: WGRM-05 LC MS
Technical data
Part No. Max. axial max. axial max. axial Max. axial
Weight
tensile force compressive force tensile force tensile force
Right thread Left thread ball stud axis ball stud axis housing axis in housing axis with metal
ball stud
Short term Long term Short term Long term Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [g]
Order key
WG ... M - 05 LC
Inner-Ø [mm]
Absolute corrosion-resistance
Low cost
Easy assembly (16.8 lbs) and disassembly
Thread
Metric
High holding forces in the assembled condition (58.4 lbs)
Ball stud made of plastic on request
Material:
Housing - igumid G ➤ Page 1373
Ball stud - galvanized steel20)
1
1
a a a d4 d4 d4 b b b
Ød
Ød
Ød h1
h1
h1
S1
S1
S1
d2
d2
d2
l1
l1
l1
e e e
h3
h3
h3
l5 l5 l5
l2
l2
l2
l6
l6
l6
S2 S2 S2
d2 d2 d2
WGRM-05-DE WGLM-05-DE 7.9 44.9 8.0 M5 12.8 9.0 10.2 13.0 3.4
WGRM-06-DE WGLM-06-DE 11.2 61.8 10.0 M6 16.0 11.0 12.5 14.5 5.5
20)
only available with right-hand thread
WGRM-05-DE WGLM-05-DE 8.2 10.8 25.6 SW9 SW7 25.0 31.4 11.0 18° 25°
WGRM-06-DE WGLM-06-DE 10.5 13.0 32.0 SW11 SW8 30.0 38.0 12.0 18° 25°
Inner-Ø [mm]
Thread
Metric
S1
d4 d2
Material:
e
h3
ø d1
l1
l2
l3
S2
d2
Dimensions [mm]
Part No. Part No. d1 d2 d4 l1 l2 l3 h3 S1 S2 a b e Pivot angle
Right thread Left thread +0.1 +0.5 +0.2 +0.3 +0.5 +0.3 +0.5
–0.1 –0.5 –0.2 –0.3 Min. –0.5 –0.3 –0.5 Min. Recommended Maximum
AGRM-08 AGLM-08 13.0 M8 19.3 13.0 16.5 13.5 59.0 SW12 SW11 29.5 36.5 16.0 18° 25°
19)
Metal stud option: MS = metal stud, only available with right-hand thread. Example: WGRM-05 LC MS
Technical data
Part No. Max. axial max. axial Maximum
Weight
tensile force compressive force assembling force
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [g]
Order key
AG ... M - 06 LC
Inner-Ø [mm]
Low cost
Thread
Metric
S1
d4
d2
Material:
Housing - igumid G ➤ Page 1373
e
a
b
h3
ød1
l1
l2
l3
S2
d2
Dimensions [mm]
Part No. Part No. d1 d2 d4 l1 l2 l6 h3 S1 S2 a b e
Right thread Left thread ± 0.1 ± 0.5 ± 0.2 ± 0.3 ± 0.3 ± 0.5 Min.
AGRM-08 LC AGLM-08 LC 10.0 M6 14.8 11.0 11.3 7.3 47.3 SW9 10.0 25.0 29.9 13.0
19)
Metal stud option: MS = metal stud, only available with right-hand thread. Example: WGRM-05 LC MS
Technical data
Part No. Max. static axial max. static axial Pivot angle
Weight
tensile strength compressive strength
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g] Recommended Maximum
785
igubal®
clevis igubal® Clevis Joints
joints
igubal® clevis joints are all made of igumid G to DIN 71752, which can be used in combination with E series rod ends. Available
components are clevis joint, clevis pin and clip or as an alternative, spring-loaded pin.
Lightweight
max. +248°F
F
min. –22°F
4 types
mm Ø 4 to 20 mm
General information
igubal® clevis joints are made of igumid G according to DIN 71752. The clevis joints are available in a variety of configurations.
igubal® clevis joints can be used in difficult circumstances without any problems. The clevis joints are corrosion resistant in moist or wet
environments and the sliding bearings are resistant to weak acids and alkalis. The operating temperatures range from -22°F to +248°F.
igubal® clevis joints are made out of a high-wear resistant material which requires no lubrication.
Loads
The load-bearing capacity of the maintenance-free, polymer clevis
joints is very high at normal ambient temperatures. They absorb
high forces, possess very good vibration dampening properties
and yet weigh only a fifth of conventional metallic bearing housings.
However, plastic specific properties, such as dependence on
temperature and behavior under long term stressing, must be taken
into consideration when using the clevis joints. The load-bearing
capacity of the clevis joints in individual cases should therefore be
checked in a practical test, particularly if they are to be used under
continuously high loads and at elevated temperatures.
Tensile
Radial Axial
Combination,
easy to fit
E series
GERMFE
GELMFE
➤ Page 799
Lightweight
High strength under impact loads
Corrosion resistance
High tensile strength
Can be used in combination with E series rod ends
Vibration-dampening
Noise-dampening
Available in right- (GERI) and left-hand-thread (GELI)
Dimensions [inch]
Part No. Part No. d1 g a1 a2 b1 d2 d3 f l1 l2 l3
H9 h11 +0.3 Thread- +0.3 +0.3 +0.5 +0.3 +0.2
Right thread Left thread -0.16 Tolerance 6H -0.3 -0.3 -0.5 -0.3 -0.2
GERI-03 GELI-03 0.1875 0.394 0.394 0.394 0.197 10-32 0.354 .02 1.024 0.787 0.295
GERI-04 GELI-04 0.2500 0.472 0.472 0.472 0.236 1/4-28 0.394 .02 1.205 0.945 0.354
GERI-05 GELI-05 0.3125 0.630 0.630 0.630 0.315 5/16-24 0.551 .02 1.638 1.260 0.472
GERI-06 GELI-06 0.3750 0.787 0.787 0.787 0.394 3/8-24 0.709 .02 2.020 1.575 0.591
GERI-07 GELI-07 0.4375 0.945 0.945 0.945 0.472 7/16-20 0.787 .02 2.413 1.890 0.709
GERI-08 GELI-08 0.5000 1.102 1.063 1.063 0.551 1/2-20 0.945 .02 2.807 2.205 0.886
d1 Order key
f
b1
Type Size
G E ... I - 08
90°
g
l1
Based on 1/16”
l3
Inner-Ø [inch]
Clevis joint
d2
d3
Thread
a1
Inch
a2
Material:
igumid G ➤ Page 1373
Technical data
Part No. Part No. Max. static Weight
Tensile Strength
Right thread Left thread Short term Long term
[lbs] [lbs] [g]
Lightweight
High strength under impact loads
Corrosion resistance
High tensile strength
Can be used in combination with E series rod ends
Vibration-dampening
Noise-dampening
Available in right- (GERM) and left-hand-thread (GELM)
Dimensions [inch]
Part No. Part No. d1 g a1 a2 b1 d2 d3 l2 h1 l1
Right thread Left thread H9 h11 +0.3 Thread- +0.3 +0.5 +0.3 +0.2
-0.16 Tolerance 6H -0.3 -0.5 -0.3 -0.
Type Size
G E ... M - 08
g
I2
Inner-Ø [mm]
Clevis joint
d2
Thread
Metric
a1
d3
a2 Material:
igumid G ➤ Page 1373
Technical data
Part No. Part No. Max. static Max. static Max. torque
Weight
Tensile Strength Radial Load strength
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [ft•lbs] [g]
GERM-04 M3.5 GELM-04 M3.5 146 73 56 28 0.3 0.9
GERM-04 GELM-04 179 90 56 28 0.3 0.9
GERM-05 DIN M4 GELM-05 DIN M4 225 112 56 28 0.3 1.5
GERM-05 DIN M5 GELM-05 DIN M5 225 112 56 28 0.4 1.5
GERM-05 GELM-05 270 135 56 28 0.4 2.7
GERM-05 DIN M5 LS22) GELM-05 DIN M5 LS22) 225 112 29 15 0.4 2.3
GERM-06 GELM-06 315 157 67 34 1.1 2.5
GERM-06 LS22) GELM-06 LS22) 315 157 29 15 1.1 3.6
GERM-08 GELM-08 607 303 146 73 3.7 6.3
GERM-10 GELM-10 1057 528 180 90 11.1 13.2
GERM-10 F GELM-10 F 1057 528 180 90 4.4 13.2
GERM-12 GELM-12 1281 640 202 101 14.8 20.2
GERM-12 F GELM-12 F 1281 640 202 101 11.1 20.2
GERM-14 GELM-14 1484 741 225 112 18.4 29.9
GERM-14 F GELM-14 F 1484 742 225 112 14.8 29.9
GERM-15 GELM-15 719 360 225 112 18.4 30
GERM-16 GELM-16 1686 843 270 135 22.1 49.9
GERM-16 F GELM-16 F 1686 843 270 135 20.3 49.9
GERM-17 GELM-17 809 405 270 135 22.1 50
GERM-17 F GELM-17 F 809 405 270 135 20.3 50
GERM-20 GELM-20 2136 1068 674 337 44.3 105
GERM-20 M20 GELM-20 M20 2136 1068 674 337 59.0 105
22)
LS = longer shank
Order key
Type Size
G E ... I K - 04
Based on 1/16”
Inner-Ø [inch]
Clevis joint
Thread
Lightweight
inch
Corrosion resistance
High tensile strength
Can be used in combination with E series rod ends Material:
igumid G ➤ Page 1373
Technical data
Part No. Part No. Max. static Weight
Tensile Strength
Right thread Left thread Short term Long term
[lbs] [lbs] [g]
Order key
Type Size
G E ... M K - 04
Inner-Ø [mm]
Clevis joint
Thread
Lightweight
Metric
Corrosion resistance
High tensile strength
Can be used in combination with E series rod ends Material:
igumid G ➤ Page 1373
Technical data
Part No. Part No. Max. static Max. static
Weight
Tensile Strength Radial Load
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GERMK-04 M3.5 GELMK-04 M3.5 112 56 56 28 1.3
GERMK-04 GELMK-04 112 56 56 28 1.3
GERMK-05 DIN M4 GELMK-05 DIN M4 180 90 56 28 2.1
GERMK-05 DIN M5 GELMK-05 DIN M5 180 90 56 28 2.1
GERMK-05 GELMK-05 202 101 56 28 3.3
GERMK-05 DIN M5 LS22) GELMK-05 DIN M5 LS22) 180 90 29 15 2.9
GERMK-06 GELMK-06 292 146 67 33 3.3
GERMK-06 LS22) GELMK-06 LS22) 292 146 29 15 4.4
GERMK-08 GELMK-08 472 236 146 73 7.9
GERMK-10 GELMK-10 674 337 180 90 16.4
GERMK-10 F GELMK-10 F 674 337 180 90 16.4
GERMK-12 GELMK-12 787 393 202 101 25.3
GERMK-12 F GELMK-12 F 787 393 202 101 25.3
GERMK-14 GELMK-14 1371 685 224 112 31.2
GERMK-15 GELMK-15 629 315 224 112 38.9
GERMK-16 GELMK-16 1573 786 270 135 60.8
GERMK-16 F GELMK-16 F 1573 786 270 135 60.8
GERMK-17 GELMK-17 809 405 270 135 62.3
GERMK-17 F GELMK-17 F 809 405 270 135 62.3
GERMK-20 GELMK-20 2023 1012 674 337 125.2
GERMK-20 M20 GELMK-20 M20 2023 1012 674 337 125.2
d1
l1
h1
I2
d2
Material:
igumid G ➤ Page 1373
Dimensions [mm]
Part No. d1 d2 a b C l1 h1 l2 Weight
h11 ±0.5 [g]
GEFM-04 4 8 9.5 10.5 8 19 15 4.5 0.5
GEFM-05 DIN 5 9 12 13.5 8 23 19 5.5 0.8
GEFM-05 DIN M5 LS22) 5 9 12 13.5 8 33 29 5.5 1.0
GEFM-05 5 10 14 15.5 8 27 23 6.5 1.1
GEFM-06 LS22) 6 10 14 15.5 8 39 35 6.5 1.0
GEFM-06 6 10 14 15.5 8 27 23 6.5 1.2
GEFM-08 8 14 19 21.0 11 35.5 30 8.0 2.8
GEFM-10 10 18 23 25.5 14 45 38 10.0 5.0
GEFM-12 12 20 28 31.0 16 53 45 12.0 8.3
GEFM-16 16 26 36 40.0 22 73 62 16.0 18.3
22)
LS = longer shank
Order key
Type Size
G E ... M F - 04
Inner-Ø [mm]
Clevis joint
Single piece design
Thread
Metric
Easy to assemble
Easy assembly also in hard to reach locations
Can be used in combination with E series rod ends Material:
Corrosion-resistant and lightweight igumid G ➤ Page 1373
Technical data
Part No. Max. static tensile strength Max. static radial load Weight
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GERMF-04 M3.5 GELMF-04 M3.5 112 56 56 28 1.3
GERMF-04 GELMF-04 112 56 56 28 1.3
GERMF-05 DIN M4 GELMF-05 DIN M4 180 90 56 28 2.3
GERMF-05 DIN M5 GELMF-05 DIN M5 180 90 56 28 2.3
GERMF-05 DIN M5 LS22) GELMF-05 DIN M5 LS22) 180 90 56 28 2.3
GERMF-05 GELMF-05 202 101 56 28 3.8
GERMF-06 GELMF-06 292 146 67 34 3.9
GERMF-06 LS22) GELMF-06 LS22) 292 146 29 15 3.9
GERMF-08 GELMF-08 472 236 146 73 9.1
GERMF-10 GELMF-10 674 337 180 90 18.2
GERMF-10 F GELMF-10 F 674 337 180 90 18.2
GERMF-12 GELMF-12 787 393 202 101 28.6
GERMF-12 F GELMF-12 F 787 393 202 101 28.6
GERMF-16 GELMF-16 1574 787 270 135 61.8
GERMF-16 F GELMF-16 F 1574 787 270 135 61.8
22)
LS = longer shank
Order key
Type Size
G E ... M K E - 05
Inner-Ø [mm]
and rod end
Clevis joint
Thread
Metric
Lightweight
Corrosion resistance Material:
High tensile strength igumid G ➤ Page 1373
Can be used in combination with E series rod ends
Technical data
Part No. Max. static Max. static Weight
tensile strength radial load
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GERMKE-05 GELMKE-05 202 101 34 17 6.4
GERMKE-06 GELMKE-06 292 146 45 22 7.3
GERMKE-08 GELMKE-08 450 225 101 51 14.6
GERMKE-10 GELMKE-10 517 259 112 56 27.1
GERMKE-10 F GELMKE-10 F 517 259 112 56 27.1
GERMKE-12 GELMKE-12 742 371 124 62 42.7
GERMKE-12 F GELMKE-12 F 742 371 124 62 42.7
GERMKE-15 GELMKE-15 630 315 180 90 68.4
GERMKE-16 GELMKE-16 1124 562 191 96 86.9
GERMKE-16 F GELMKE-16 F 1124 562 191 96 86.9
GERMKE-17 GELMKE-17 809 405 247 124 98.3
GERMKE-17 F GELMKE-17 F 809 405 247 124 98.3
GERMKE-20 GELMKE-20 1619 809 405 202 175.2
GERMKE-20 M20 GELMKE-20 M20 1619 809 405 202 175.2
Clevis joints with spring-loaded fixing clip can be used in combination with E series rod ends
EBRM and EARM ➤ Page 764
Order key
Type Size
G E ... M F E - 05
Inner-Ø [mm]
and rod end
Clevis joint
Thread
Metric
Material:
igumid G ➤ Page 1373
Technical data
Part No. Max. static Max. static Weight
tensile strength radial load
Right thread Left thread Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GERMFE-05 GELMFE-05 202 101 34 17 7.0
GERMFE-06 GELMFE-06 292 146 45 22 7.9
GERMFE-08 GELMFE-08 450 225 101 51 15.9
GERMFE-10 GELMFE-10 517 259 112 56 29.2
GERMFE-10 F GELMFE-10 F 517 259 112 56 29.2
GERMFE-12 GELMFE-12 742 371 124 62 46.0
GERMFE-12 F GELMFE-12 F 742 371 124 62 46.0
GERMFE-16 GELMFE-16 1124 562 191 96 94.4
GERMFE-16 F GELMFE-16 F 1124 562 191 96 94.4
Clevis joints with spring-loaded fixing clip can be used in combination with E series rod ends
EBRM and EARM ➤ Page 764
Dimensions (inch)
l1
l
Part Number d1 d2 d l l1 m Clip Weight
Pin
m
GBI-03 .1875 .1260 .3125 .55 .3975 .0472 GSR-04 0.4
GBI-04 .2500 .1969 .3750 .65 .4764 .0512 GSR-08 0.5 d2
d1
GBI-05 .3125 .1969 .4375 .85 .6339 .0512 GSR-08 1.5
GBI-06 .3750 .2756 .5000 1.05 .7953 .0591 GSR-10 2.8
Material:
GBI-07 .4375 .3543 .6250 1.25 .9528 .0669 GSR-12 4.6
igumid G ➤ Page 1373
GBI-08 .5000 .3543 .7500 1.40 1.0709 .0669 GSR-12 5.2
Dimensions (mm)
Part Number d1 d2 d l l1 m Clip Weight
Pin
GBM-04 4 3.2 7 12.50 8 1.05 GSR-04 0.3
GBM-05 5 4.0 8 16.50 12 1.15 GSR-06 0.5
GBM-05 DIN 5 4.0 8 14.50 10 1.15 GSR-06 0.5
GBM-06 6 4.0 9 16.50 12 1.15 GSR-06 0.7
GBM-08 8 5.0 12 21.50 16 1.15 GSR-08 1.5
GBM-10 10 7.0 15 27.00 20 1.35 GSR-10 3.0
GBM-12 12 9.0 18 31.50 24 1.50 GSR-12 4.8
GBM-14 14 12.0 22 36.00 27 1.70 GSR-16 5.7
GBM-15 15 12.0 23 36.00 27 1.70 GSR-16 8.3
GBM-16 16 12.0 24 42.00 32 1.70 GSR-16 10.4
GBM-17 17 12.0 25 42.00 32 1.70 GSR-16 12.3
GBM-20 20 15.0 30 51.00 40 2.00 GSR-20 19.2
GSR - Circlip - mm
d1
Dimensions (mm) d2
801
igubal®
pillow igubal® Pillow Block
block
The igubal® pillow block bearings consist of a housing with a bearing insert. igubal® pillow block bearings are especially
easy to install, able to compensate for misalignment and prevent edge loads.
Noise-dampening
Lightweight
max. +176°F
F
min. –22°F
Ø 3/16 to 1 inch
4 types
mm Ø 5 to 50 mm
General information
igubal® pillow blocks are made of igumid G according to DIN 71752. The pillow blocks are available in a variety of configurations.
igubal® pillow blocks can be used in difficult circumstances without any problems. The pillow blocks are corrosion resistant in moist or
wet environments and the sliding bearings are resistant to weak acids and alkalis. The operating temperatures range from -22°F to +176°F.
igubal® pillow blocks are made out of a high-wear resistant material which requires no external lubrication.
Loads
The load capacity of the maintenance-free igubal® bearing elements is very high at normal ambient temperatures. igubal® bearings absorb
high forces and weigh only one fifth of traditional, metal bearing housings. The excellent dampening properties are based on the fact that
the polymer material of the two part bearing can absorb vibrations differently than steel. h
m
However, plastic specific properties, such as dependence on t emperature and behavior under long-term
h1 stress, must be taken into con-
sideration when using igubal® bearings. The load B capacity of the pillow block should therefore be checked in a practical test, particularly
A high loads and at elevated temperatures.A
if it will be used under continuous
C1
B
R1
B d1
Fa Axial F
a
d3 Pivot angle
h2
Axial Strength
Fz Fd
Fs
Easy to disassemble, Easy to fit For quick assembly and low moisture
split housing and ball absorption
K series E series E series
KSTM-GT ESTM ESTM-GT...-GT
Dimensions [mm]
Part No. d1 B C1 h1 h2 m a h3 d2 X2 Max. pivot
[E10] angle
KSTI-03 .1875 .312 .234 .290 .566 1.00 1.40 .165 .137 .200 25º
KSTI-04 .2500 .375 .250 .390 .705 1.25 1.75 .205 .137 .250 25º
KSTI-05 3125 .437 .312 .430 .824 1.35 1.95 .236 .150 .280 25º
KSTI-06 .3750 .500 .359 .550 1.022 1.80 2.40 .376 .180 .300 22º
KSTI-07 .4375 .562 .406 .570 1.082 1.85 2.50 .315 .205 .330 22º
KSTI-08 .5000 .625 .453 .600 1.191 2.00 2.80 .354 .205 .380 22º
KSTI-10 .6250 .750 .484 .700 1.409 2.30 3.35 .413 .205 .470 22º
KSTI-12 .7500 .875 .593 .860 1.687 2.70 3.75 .472 .270 .530 22º
KSTI-16 1.00 1.375 1.005 1.10 2.163 3.50 5.00 .630 .520 .680 20º
K ST I - 05
h2
h1
h3
Dimensional K series
m
Based on 1/16”
Inner-Ø [inch]
C1
d2
B
Inch
x2
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Technical data
Part No. Max. static Max. axial static Max. torque Weight
tensile strength compressive strength for longitudinal holes
The maximum torques for longitudinal holes correspond to the permissible torque of the fixing screws (fixing category 5.8).
*W300 is the European material equivalent for iglide® L280.
Dimensions [mm]
Part No. d1 B C1 h1 h2 m a h3 d2 X2 Max. pivot
[E10] angle
KSTM-05 5 8 6.0 7 14 25 34 4 3.3 4.6 30°
KSTM-06 6 9 7.0 10 18 33 43 5.5 4.5 6 29°
KSTM-08 8 12 9.0 10 20 33 47 6 4.5 7 25°
KSTM-10 10 14 10.5 14 26 46 62 7.5 5.5 8 25°
KSTM-12 12 16 12.0 14 28 46 65 8.5 5.5 9 25°
KSTM-14 14 19 13.5 18 34 60 82 9.5 6.6 11 23°
KSTM-16 16 21 15.0 18 36 60 86 10.5 6.6 12 23°
KSTM-18 18 23 16.5 22 42 68 93 11.5 9.0 13 23°
KSTM-20 20 25 18.0 22 44 68 98 13 9.0 14 23°
KSTM-22 22 28 20.0 24 48 74 108 14 9.0 16 22°
KSTM-25 25 31 22.0 27 54 86 124 16 9.0 17 22°
KSTM-30 30 37 25.0 32 64 96 139 17 11.0 20 22°
K ST M - 05
h2
h1
h3
Dimensional K series
m
Based on 1/16”
Inner-Ø [inch]
C1
d2
B
Metric
x2
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Technical data
Part No. Max. static tensile strength Max. axial static Max. torque for Weight
Short term Long term compressive strength longitudinal holes
[lbs] [lbs] [lbs] [ft lbs] [g]
sw
B
Dimensional K series
Inner-Ø [mm]
h2
Metric
h1
Material:
Housing: RN33
Spherical ball: iglide® J
m h
h1
C1
sw
B
d1
a
Dimensionsd3[mm]
(2x)
Part No. d1 d3 h h1 h2 SW a m C1 B
h2
KSTM-GT40-GT 24)
40.0 13.5 79.0 39.5 12.6 19.0 120.5 91.0 29.5 48.5 24°
KSTM-GT4523) 45.0 13.5 100.0 50.0 12.6 19.0 149.0 114.0 35.0 60.0 24°
KSTM-GT50 50.0 13.5 100.0 50.0 12.6 19.0 149.0 114.0 35.0 60.0 24°
KSTM-GT50-GT24) 50.0 13.5 100.0 50.0 12.6 19.0 149.0 114.0 35.0 60.0 24°
Technical data
Part No. Max. radial Max. axial Max. torque Weight
tensile strength tensile strength through ball fixing holes
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [ft lbs] [ft lbs] [g]
KSTM-GT35 23)
2,473 1,236 562 281 14.8 11.1 250.3
KSTM-GT40 2,473 1,236 562 281 14.8 11.1 235.0
KSTM-GT40-GT 24)
2,473 1,236 562 281 14.8 11.1 235.0
KSTM-GT4523) 3,372 1,686 674 337 14.8 14.8 405.2
KSTM-GT50 3,372 1,686 674 337 14.8 14.8 389.2
KSTM-GT50-GT24) 3,372 1,686 674 337 14.8 14.8 389.2
*Inside diameter achieved with plain iglide® J bearing pressed into ID of spherical ball
**Spherical balls are also available with split design
C1
B
Adapter available
Dimensional E series
R1
Inner-Ø [mm]
h2
C1
C1
BB
Metric
1
RR1
d1
d1
aa
d3
d3
Material:
d2
Housing: igumid G ➤ Page 1373
h2
h2
Dimensions [mm] d2
d2
Part No. d1 d2 d3 h h1 h2 a m C1 B R1 Max. pivot angle
[E10]
ESTM-08 8.0 4.5 – 19 9.5 – 31.0 22.0 9.0 8.0 4.5 22°
ESTM-10 10.0 5.5 – 22 11 – 36.0 26.0 10.0 9.0 5.0 22°
ESTM-12 12.0 5.5 – 26 13 – 38.0 28.0 10.0 10.0 5.0 22°
ESTM-16 16.0 6.6 10.6 34.0 17.0 6.4 50.0 37.0 13.0 13.0 6.5 22°
ESTM-20 20.0 9.0 14.0 40.0 20.0 8.6 62.0 46.0 16.0 16.0 8.0 22°
ESTM-25 25.0 9.0 14.0 48.0 24.0 8.6 72.0 54.0 18.0 20.0 9.0 20°
ESTM-30 30.0 11.0 17.0 56.0 28.0 10.6 86.0 64.0 22.0 22.0 11.0 20°
Technical data
Max. static radial Max. static radial Max. axial Max. torque
Part No. Weight
tensile strength compressive strength strength fixing holes
Short term Long term Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [ft lbs] [g]
* Due to the different manufacturing method, the load values of the ESTM-30 are lower than ESTM-25
➤ Tolerance Table, Page 75
C1
B
DIN ISO 12240
Dimensional E series
Inner-Ø [mm]
d3
Metric
h2
Material:
Housing: RN33
Spherical ball: iglide® J
d2
h
m h1
C1
B
d1
R1
a
Dimensions [mm] d3
Part No. d1 d2 d3 h h1 h2 a m C1 B R1 Max. pivot angle
h2
[E10]
ESTM-GT16-GT 16.0 6,6 10.6 34.0 17.0 6.4 50.0 37.0 13.0 13.0 6.5 22°
ESTM-GT20-GT 20.0 9,0 14.0 40.0 20.0 8.6 62.0 46.0 16.0 16.0 8.0 22°
ESTM-GT25-GT 25.0 9,0 14.0 48.0 24.0 8.6 72.0 54.0 18.0 20.0 9.0 22°
ESTM-GT30-GT 30.0 11.0 17.0 56.0 28.0 10.6 86.0 64.0 22.0 22.0 11.0 22°
d2
Technical data
Part No. max. static radial load max. static radial compressive force Weight
Dimensional E series
Inner-Ø [mm]
Dimension
C1
Metric
R1
d1
Material:
igumid G ➤ Page 1373
a
d3
h2
d2
Dimensions [mm]
Part No. d1 d2 d3 h h1 h2 a m C1 R1 Weight
[E10] [g]
ESTM-GT16-25 25.0 6.6 10.6 34.0 14.0 6.4 50.0 37.0 13.0 6.5 12.6
ESTM-GT20-30 30.0 9.0 14.0 40.0 20.0 8.6 62.0 46.0 16.0 8.0 21.1
ESTM-GT25-35 35.0 9.0 14.0 48.0 24.0 8.6 72.0 54.0 20.0 9.0 39.9
ESTM-GT30-40 40.0 11.0 17.0 56.0 28.0 10.6 86.0 64.0 22.0 11.0 66.5
Dimensional E series
Dimensions [mm]
Part No. d1 d2 h h1 h2 a m B R1 Weight
[E10] [g]
ESTM-GT 150 150 24 180 90 15 250 200 50 25 980
Dimensional E series
h1
Inner-Ø [mm]
Slimline
C1
Metric
d1
h Material:
R1 Housing: igumid G ➤ Page 1373
Spherical ball: iglide® J
h2
d2
m
a
Dimensions [mm]
Part No. d1 d2 h h1 h2 a m C1 R1 Max. pivot
[E10] angle
ESTM-05 SL 5.0 2.5 18.0 10.0 6.5 16.0 10.0 6.0 8.0 17°
ESTM-06 SL 6.0 2.5 18.0 10.0 6.5 16.0 10.0 6.0 8.0 17°
ESTM-08 SL 8.0 2.5 19.0 10.0 6.5 18.0 12.0 6.0 9.0 17°
ESTM-10 SL 10.0 2.5 20.0 10.0 6.5 20.0 14.0 6.0 10.0 17°
Technical data
Max. radial Max. radial Max. lateral Max. axial
Part No. Weight
tensile strength compressive strength strength strength
Short term Long term Short term Long term Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [g]
ESTM-05 SL 337 169 315 157 202 101 34 17 1.6
ESTM-06 SL 337 169 315 157 202 101 34 17 1.7
ESTM-08 SL 360 180 315 157 214 107 22 11 1.7
ESTM-10 SL 360 180 315 157 214 107 22 11 1.9
Order key
Type Size
AD - E ST M - 40
Dimensional E series
Inner-Ø [mm]
Corrosion- and chemical-resistant
Fits directly
Adapter
Metric
Space-saving
Same screws as traditional metallic versions
LL
h1
h1
øM
øMx
x
øM
øMx
x
JJ Fz Fd
R1R1
Fa Fs
N
A
N
mm
NN
1
1
Dimensions [mm]
Part No. for d1 L A R1 J h1 N N1 m Mx
ESTM-…
AD-01-ESTM-2026) ESTM-20 20 130 20 10.0 97 14.0 11 8 46 M8
AD-01-ESTM-2527) ESTM-25 25 130 20 10.0 102 12.5 11 9 54 M8
AD-01-ESTM-3027) ESTM-30 30 158 25 12.5 118 14.9 14 10 64 M10
Technical data
Part No. Max. radial Max. radial Maximum Maximum
Weight
tensile strength compressive strength axial strength lateral strength
[Fz] [Fd] [Fa] [Fs]
Short term Long term Short term Long term Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [lbs] [g]
AD-01-ESTM-20 26)
540 270 2,250 1,125 675 335 270 135 29.8
AD-01-ESTM-2527) 540 270 2,250 1,125 675 335 270 135 74.0
AD-01-ESTM-30 27)
540 270 2,250 1,125 675 335 270 135 124.0
Material: plastic
26)
Material: aluminum
27)
igubal® Flange bearings have been developed for the support of shaft ends or for shafts lead-through. Like all igubal® products, these bearings consist
of an igumid G housing and an iglide® L280 spherical ball (with other options available). igubal® Flange bearings are made to the dimensional E series
and are offered with two or four mounting holes.
Maintenance-free,
dry running
max. +176°F
F
min. –40°F
Ø 3/8 to 1 inch
4 types
mm Ø 4 to 50 mm
General Properties
igubal® Flange bearings have been developed for the support of shaft ends or for shafts lead-through. Like all igubal® products, these
bearings consist of an igumid G housing and an iglide® L280 spherical ball (with other options available). igubal® Flange bearings are
made to the dimensional E series and are offered with two or four mounting holes.
Areas of Application
Since igubal® flange bearings are made for maintenance-free
use, they are especially suited for applications in which access
to the bearing is limited, in moist or wet environments or clean-
room environments. Thus, igubal® flange bearings are also found
in electric toothbrushes, awnings, conveyor technology, bakery
machines and agriculture to name a few.
Installation
igubal® flange bearings are designed for mounting with 2 or 4
bolts, depending on the design. The 2-hole types are provided
with elongated holes, which allow a problem-free adjustment.
An exact positioning of the bearing housing is not necessary,
since the spherical ball compensates for misalignment.
Pivot Angle
Easy to install Easy to install For higher radial load For higher radial load
Inch dimensions metric dimensions Inch dimensions Metric dimensions
Universal and quick assembly Universal and quick assembly High static load, split housing
Female thread Male thread
K series
GFSM-IG GFSM-AG KFSM-GT
E series E series
EFOM-HT EFSM-HT
➤ Page 833 ➤ Page 834
Dimensions [mm]
Part No. d1 dB H L J A1 Ag N
[E10] Height of Bore diameter
Hole pitch Total height
housing dx1
EFOI-03 0.1875 0.551 1.331 0.630 0.945 0.177 0.312 0.126 x 0.197
EFOI-04 0.2500 0.551 1.331 0.630 0.945 0.177 0.342 0.126 x 0.197
EFOI-05 0.3125 0.709 1.740 0.866 1.220 0.217 0.412 0.169 x 0.256
EFOI-06 0.3750 0.866 2.047 1.024 1.417 0.256 0.483 0.210 x 0.315
EFOI-07 0.4375 0.984 2.232 1.220 1.614 0.276 0.518 0.210 x 0.315
EFOI-08 0.5000 0.984 2.232 1.220 1.614 0.276 0.518 0.210 x 0.315
EFOI-10 0.6250 1.260 2.858 1.496 2.087 0.394 0.683 0.212 x 0.315
EFOI-12 0.7500 1.575 3.504 1.850 2.559 0.433 0.785 0.331 x 0.492
EFOI-16 1.0000 1.909 3.976 2.303 2.953 0.551 0.966 0.331 x 0.492
Type Size
E F O I - 04
N
Dimensional E series
m
Based on 1/16”
Flange bearing
h
Inner-Ø [inch]
2 holes
Ag
A1
Inch
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
axial load radial load torque pivot angle
Short term Long term Short term Long term holes
[lbs] [lbs] [lbs] [ft lbs] [ft lbs] [g]
EFOI-03 56 28 168 84 0.44 33° 2.3
EFOI-04 56 28 180 90 0.96 27° 2.0
EFOI-05 156 78 248 124 1.84 24° 4.0
EFOI-06 192 96 450 225 1.84 24° 6.5
EFOI-07 248 124 494 247 1.84 21° 7.5
EFOI-08 248 124 494 247 3.32 21° 12.0
EFOI-10 314 157 630 315 3.32 24° 17.2
EFOI-12 404 202 1236 618 3.32 17° 33.7
EFOI-16 674 337 1348 674 7.74 14° 59.0
Dimensions [mm]
Part No. d1 dB H L J A1 Ag N
[E10] Height of Bore diameter
Hole pitch Total height
housing dx1
Type Size
E F O M - 04
N
Dimensional E series
m
Flange bearing
h
Inner-Ø [mm]
2 holes
Ag
Metric
A1
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
axial load radial load torque pivot angle
Short term Long term Short term Long term Holes
[lbs] [lbs] [lbs] [ft lbs] [ft lbs] [g]
EFOM-04 90 45 168 84 0.44 28° 1.9
EFOM-05 90 45 168 84 0.44 29° 2.3
EFOM-06 112 56 180 90 0.44 25° 1.8
EFOM-08 158 78 247 124 0.96 25° 4.1
EFOM-10 191 96 450 225 1.84 25° 6.8
EFOM-12 247 124 495 247 1.84 21° 8.9
EFOM-15 292 146 540 270 3.32 20° 15.0
EFOM-16 315 158 629 315 3.32 27° 17.7
EFOM-17 405 202 719 360 3.32 21° 24.9
EFOM-20 405 202 1236 618 7.74 19° 32.8
EFOM-25 674 337 1348 674 7.74 15° 58.5
EFOM-30 687 393 1461 730 15.86 14° 78.9
Dimensions [mm]
Part No. d1 dB L J A1 Ag N
[E10] Bore diameter
Hole pitch Height of housing Total height
dx1
Order key
N
Type Size
E F S I - 04
m
h
Dimensional E series
Based on 1/16”
Flange bearing
Inner-Ø [inch]
Ag
A1
4 Holes
Inch
d1
dB
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
N
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
m
h
Dimensions [mm]
Part No. d1 dB L J A1 Ag N
[E10] Bore diameter
Hole pitch Height of housing Total height
dx1
Order key
N
Type Size
E F S M - 04
m
h
Dimensional E series
Flange bearing
Inner-Ø [mm]
Ag
A1
4 Holes
Metric
d1
dB
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
N
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
m
h
GF S M - 06 - IG
Ag
h
m A1
Flange mounted
l6
Female thread
Inner-Ø [mm]
Ag
4 Holes
d2
Metric
A1
l6
Material:
Housing: igumid G ➤ Page 1373
S1 N
Ball stud: Galvanized steel 28)
d2
Force test
direction
Dimensions [mm]
Part No. d2 m h Ag A1 l6 N S1
[E10]
GFSM-06-IG M6 17.0 25.0 29.0 4.5 11.0 3.2 SW11
GFSM-08-IG M8 22.0 33.0 36.0 5.5 12.0 4.3 SW14
GFSM-10-IG M10 26.0 38.0 43.5 6.5 16.0 5.3 SW17
Technical data
Max. axial Max. axial
Part No. Max. pivot angle Weight
tensile force compressive force
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GFSM-06-IG 33.7 16.9 78.7 39.3 32° 16.4
GFSM-08-IG 56.2 28.1 168.6 84.3 34° 34.0
GFSM-10-IG 31.5 15.7 269.8 134.9 40° 61.1
28)
Stainless steel ball stud on request
GF S M - 06 - AG
Ag
h
m A1
l6
Flange mounted
Inner-Ø [mm]
Male thread
Ag
4 Holes
d2
A1
Metric
l6
Material:
Housing: igumid G ➤ Page 1373
S1 N
Ball stud: Galvanized steel28)
d2
Force test
direction
Dimensions [mm]
Part No. d2 m h Ag A1 l6 N S1
[E10]
GFSM-06-IG M6 17.0 25.0 29.0 4.5 10.5 3.2 SW8
GFSM-08-IG M8 22.0 33.0 36.0 5.5 13.5 4.3 SW11
GFSM-10-IG M10 26.0 38.0 43.5 6.5 16.0 5.3 SW13
Technical data
Max. axial Max. axial
Part No. Max. pivot angle Weight
tensile force compressive force
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
GFSM-06-IG 33.7 16.9 78.7 39.3 32° 10.6
GFSM-08-IG 56.2 28.1 168.6 84.3 34° 23.1
GFSM-10-IG 31.5 15.7 269.8 134.9 40° 41.2
28)
Stainless steel ball stud on request
Dimensional K series
Predictable lifetime
Maintenance free, dry-running
Split housing
Inner-Ø [mm]
without plug-in feet M12
4 Holes
N
Metric
Material:
m
h
Housing: RN33
Spherical ball: iglide® J
A2
dk
A1
B
d3
d1
dn Example: KFSM-GT-40-A
Dimensions [mm]
Part No. d1 dn d3 dk A1 A2 B m h N
[E10] Height of Bore diameter
Hole pitch Total height
housing dx1
KFSM-GT35 35.0 59.0 26.0 66.0 30.0 45.0 48.5 66.0 92.0 13.5
KFSM-GT40 40.0 59.0 26.0 66.0 30.0 45.0 48.5 66.0 92.0 13.5
KFSM-GT45 45.0 72.0 26.0 82.0 40.0 60.0 60.0 78.0 104.0 13.5
KFSM-GT50 50.0 72.0 26.0 82.0 40.0 60.0 60.0 78.0 104.0 13.5
For KFSM with spacer feet, please add an "A" to the part no. Example: KFSM-GT50-A.
23)
Diameter given by iglide® J bore reducer
➤ Tolerance Table, Page 75
Technical data
Part No. Maximum static Maximum static Max. pivot angle Weight
radial load axial load
Dimensional E series
Underwater use
High temperature
dB
Flange bearing
d1
Inner-Ø [mm]
2 holes
Metric
N
Material:
Housing: iguton G
m Spherical ball: iglide® T500 (X)
h
Ag
A1
Dimensions [mm]
Part No. d1 dB H L m A1 Ag N
[E10] Length Width Bore diameter
Hole pitch Height of plate Total height
dx1
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
axial load radial load torque pivot angle
Short term Long term Short term Long term Holes
[lbs] [lbs] [lbs] [lbs] [ft lbs] [g]
EFOM-05-HT 61.8 31.0 103.4 51.7 .44 29° 2.5
EFOM-06-HT 67.4 33.7 137.4 68.6 .44 27° 2.3
EFOM-08-HT 144.8 72.4 210.0 105.0 .96 24° 5.0
EFOM-10-HT 171.7 85.9 224.8 112.4 1.84 24° 8.3
EFOM-12-HT 196.5 98.2 290.0 145.0 1.84 21° 10.7
*X is the European material equivalent for iglide® T500.
E F S M - 05 HT
Corrosion-resistance
Lightweight
Chemical resistant
chemical table ➤ Page 364
Dimensional E series
Underwater use
Ag
High temperature
h
Flange bearing
Inner-Ø [mm]
m A1
4 holes
Metric
Material:
Housing: iguton G
Spherical ball: iglide® T500 (X)
dB
d1
Ag
A1
d1
N dB
Dimensions [mm]
Part No. d1 dB H m A1 Ag N
N
Technical data
Part No. Maximum static Maximum static Maximum static Maximum Weight
axial load radial load torque pivot angle
Short term Long term Short term Long term Holes
[lbs] [lbs] [lbs] [lbs] [ft lbs] [g]
EFSM-05-HT 61.8 31.0 98.9 49.5 .44 29° 3.5
EFSM-06-HT 76.2 38.2 117.6 58.9 .44 25° 3.3
EFSM-08-HT 92.6 46.3 160.3 80.0 .96 25° 7.1
EFSM-10-HT 194.2 97.1 270.2 135.1 1.84 25° 11.2
EFSM-12-HT 230.2 115.1 302.8 151.5 1.84 21° 13.3
*X is the European material equivalent for iglide T500.
®
• Easy to fit
• Extremely cost-effective
• Chemical resistant
• Lightweight
• High strength
835
igubal®
pressfit
spherical igubal® Pressfit Spherical Bearings
bearing
Ease of installation makes diverse applications possible for igubal® spherical bearings. They can be used anywhere. The
self-aligning feature offers design advantages and helps to simplify assembly.
High strength
max. +176°F
F
min. –22°F
Ø 3/16 to 1 inch
4 types
mm Ø 2 to 30 mm
The use of pivoting bearings is usually associated with heavier Maintenance-free igubal ® pivoting bearings are meant to be
traditional metal bearings, difficult installation, and high costs. oversized before being pressfit. After proper installation into
Most of the time, maintenance is still necessary over the long a recommended housing bore, the inner diameter adjusts to
term, and the bearings are only corrosion-resistant in special meet our specified tolerances. Please adhere to the catalog
designs. Often roller bearings or plain bearings malfunction specifications for housing bore and recommended shaft sizes.
prematurely due to high edge loads, or bearings must be This will help to ensure optimal performance of iglide plain
readjusted, reamed, or retrofit in order to compensate for bearings. Please contact an iglide® technical expert for support.
misalignment. ➤ Tolerance Table, Page 75
igubal® pivoting bearings put an end to all of these disadvantages
and open up many new possibilities for your engineering design.
Installation
Dimensions
Compressive Strength
Compressive Strength Compressive Strength Pivot Angle
Axial Pivot Angle
Radial Axial
e Strength
al Pivot Angle
d2
d1
Suitable for rotating, oscillating and
Dimensional K series
Based on 1/16”
Material:
30°
f
Inner-Ø [inch]
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Inch
Dimensions [inch]
Part No. d1 d2 B C f Max. pivot Weight
[E10] angle [g]
KGLI-03 .1875 .5625 .312 .218 0.3 34° 1.2
KGLI-04 .2500 .6562 .375 .250 0.3 30° 1.7
KGLI-05 .3125 .7500 .437 .281 0.3 29° 2.6
KGLI-06 .3750 .8125 .500 .312 0.5 25° 3.3
KGLI-07 .4375 .9375 .562 .343 0.5 25° 4.9
KGLI-08 .5000 1.0625 .625 .390 0.5 25° 7.1
KGLI-10 .6250 1.1875 .750 .500 0.5 23° 10.2
KGLI-12 .7500 1.4375 .875 .593 0.5 23° 17.5
KGLI-16 1.0000 2.1250 1.375 1.005 0.5 23° 62.0
Technical data
Part No. Maximum Static Maximum Torque Housing Shaft Size
Compressive Strength for the assembly Bore
radial axial
[lbs] [lbs] [ft lbs] Min Max. Min. Max.
KGLI-03 225 34 3.69 .5625 .5630 .1888 .1900
KGLI-04 337 56 7.37 .6562 .6568 .2485 .2500
KGLI-05 450 79 8.85 .7500 .7509 .3110 .3125
KGLI-06 629 90 14.75 .8125 .8134 .3735 .3750
KGLI-07 843 101 22.13 .9375 .9382 .4358 .4375
KGLI-08 955 112 25.82 1.0625 1.0632 .4983 .5000
KGLI-10 1191 169 29.50 1.1875 1.1882 .6233 .6250
KGLI-12 1911 191 40.57 1.4375 1.4383 .7479 .7500
KGLI-16 3057 562 47.94 2.1250 2.1258 .9988 1.0000
➤ Tolerance Table, Page 75 For housing bores (H7) *W300 is the European material equivalent for iglide® L280.
For shaft sizes (h7) 29)
The maximum static axial load is determined in a remote location hole
d2
d1
Suitable for rotating, oscillating and
Dimensional K series
Material:
30°
f
Inner-Ø [inch]
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Metric
Dimensions [mm]
Part No. d1 d2 B C f Max. pivot Weight
[E10] angle [g]
KGLM-02 2 8 4 3.0 0.8 32° 0.1
KGLM-03 3 10 6 4.5 0.8 32° 0.5
KGLM-05 5 13 8 6.0 0.8 30° 1.0
KGLM-06 6 16 9 6.5 0.8 29° 1.6
KGLM-08 8 19 12 9.0 0.8 25° 2.9
KGLM-10 10 22 14 10.5 0.8 25° 4.4
KGLM-12 12 26 16 12.0 0.8 25° 7.0
KGLM-14 14 28 19 13.5 0.8 23° 9.1
KGLM-16 16 32 21 15.0 0.8 23° 12.8
KGLM-18 18 35 23 16.5 0.8 23° 16.6
KGLM-20 20 40 25 18.0 0.8 23° 24.4
KGLM-22 22 42 28 20.0 0.8 22° 28.5
Technical data
Part No. Maximum Static Housing Shaft Size
Maximum Torque
Compressive Strength Bore
through the ball
radial axial
[lbs] [lbs] [ft lbs] Min Max. Min. Max.
KGLM-02 67 13 0.7 8.0000 8.0150 1.9900 2.0000
KGLM-03 119 34 2.2 10.0000 10.0150 2.9900 3.0000
KGLM-05 281 56 3.7 13.0000 13.0180 4.9800 5.0000
KGLM-06 393 90 7.4 16.0000 16.0180 5.9800 6.0000
KGLM-08 528 180 8.9 19.0000 19.0210 7.9850 8.0000
KGLM-10 798 202 14.8 22.0000 22.0210 9.9850 10.0000
KGLM-12 944 214 22.1 26.0000 26.0210 11.9820 12.0000
KGLM-14 1281 270 25.8 28.0000 28.0250 13.9820 14.0000
KGLM-16 1686 292 29.5 32.0000 32.0250 15.9820 16.0000
KGLM-18 1910 315 33.2 35.0000 35.0250 17.9820 18.0000
KGLM-20 2203 427 40.6 40.0000 40.0250 19.9790 20.0000
KGLM-22 2630 584 44.3 42.0000 42.0250 21.9790 22.0000
➤ Tolerance Table, Page 75 For housing bores (H7) *W300 is the European material equivalent for iglide® L280.
For shaft sizes (h7) 29)
The maximum static axial load is determined in a remote location hole
d1
d2
K GL I - 03 SL
Lightweight
Dimensions according to DIN 1850
Dimensional K series
f 30° 5° max.
Based on 1/16”
Inner-Ø [inch]
Slimline
d1
d2
Inch
Material:
B Housing: igumid G ➤ Page 1373
Spherical ball: iglide® R
5° max.
Dimensions [inch]
Part No. d1 d2 B f Max. pivot Weight
[E10] angle [g]
KGLI-03 SL .1875 .3750 .1875 .0200 5° 0.69
KGLI-04 SL .2500 .5000 .2500 .0200 5° 0.75
KGLI-05 SL .3125 .5000 .3125 .0200 5° 1.0
KGLI-06 SL .3750 .6250 .3750 .0200 5° 1.3
KGLI-08 SL .5000 .8125 .5000 .2000 5° 2.5
Technical data
Part No. Maximum radial Maximum Axial Housing Bore Shaft Size
compressive strength compressive strength
Short term Long term Short term Long term
[lbs] [lbs] [ft lbs] Min Max. Min. Max.
KGLI-03 SL 225 112 34 17 .3750 .3756 .1888 .1900
KGLI-04 SL 337 168 56 28 .5000 .5007 .2485 .2500
KGLI-05 SL 450 225 79 39 .5000 .5007 .3110 .3125
KGLI-06 SL 630 315 112 56 .6250 .6257 .3735 .3750
KGLI-08 SL 955 478 135 67 .8125 .8133 .4983 .5000
d1
d2
K GL M - 03 SL
Lightweight
Dimensions according to DIN 1850
Dimensional K series
f 30° 5° max.
Inner-Ø [mm]
Slimline
d1
d2
Metric
Material:
B Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
5° max.
Dimensions [inch]
Part No. d1 d2 B f Max. pivot Weight
[E10] angle [g]
KGLM-08 SL 8 14 9.0 0.5 5° 1.1
KGLM-10 SL 10 16 10.5 0.5 5° 1.5
KGLM-12 SL 12 18 12.0 0.5 5° 2.0
KGLM-16 SL 16 22 15.0 0.5 5° 3.1
Technical data
Part No. Maximum radial Maximum Axial
compressive strength compressive strength
Short term Long term Short term Long term
[lbs] [lbs] [ft lbs]
KGLM-08 SL 807 101 304 51
KGLM-10 SL 899 169 450 84
KGLM-12 SL 1012 169 506 84
KGLM-16 SL 1461 112 731 56
Inner-Ø [mm]
Slimline
dd22
Metric
d1
d1
Material:
Housing: igumid G ➤ Page 1373
330°
Technical data
Part No. Maximum radial Maximum axial 29)
29)
The maximum static axial load is determined in a remote location hole
30)
Pressfit
d2
d1
Suitable for rotating, oscillating
and linear movements
Dimensional E series
30°
f
Flange bearing
Inner-Ø [mm]
Metric
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
➤ Tolerance Table, Page 75 For housing bores (H7) *W300 is the European material equivalent for iglide® L280.
For shaft sizes (h7) 29)
The maximum static axial load is determined in a remote location hole
Inner-Ø [mm]
Low cost
Metric
d2
d1
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
f Other ball stud materials on request
30°
Sheet thickness
Inner-Ø [mm]
Metric
d2
d3
d1
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® J
Dimensions [mm]
Part No. d1 B d2 d3 Sheet metal thickness b1 b2 Max. pivot
[E10] ±0.2 y ±0.1 angle
ECLM-05-02 5 6.0 12 13 2.0 3.9 6.0 25°
ECLM-06-02 6 6.0 12 13 2.0 3.9 6.0 18°
ECLM-08-02 8 6.0 14 15 2.0 3.9 6.0 16°
ECLM-10-03 10 6.0 16 17 3.0 4.5 6.7 12°
ECLM-12-03 12 6.0 18 19 3.0 4.5 6.7 12°
ECLM-16-03 16 6.0 22 24 3.0 4.5 6.7 12°
Technical data
Part No. Max. radial compressive strength Max. axial compressive strength Weight
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
ECLM-05-02 157 79 6 3 0.5
ECLM-06-02 157 79 6 3 0.5
ECLM-08-02 225 112 6 3 0.5
ECLM-10-03 315 157 7 2 0.8
ECLM-12-03 405 202 8 2 0.8
ECLM-16-03 629 315 10 5 1.1
Sheet thickness
Inner-Ø [mm]
Heavy Duty
Metric
d3
d2
d1
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
B
Other ball stud materials on request
Dimensions [mm]
Part No. d1 B d2 d3 Y Max. pivot
[E10] ±0.15 ±0.1 angle
ECLM-08-04-HD 8.0 8.0 18.0 25 4.0 28°
ECLM-10-05-HD 10.0 9.0 22.0 28 5.0 24°
ECLM-12-06-HD 12.0 10.0 24.0 32 6.0 24°
ECLM-20-08-HD 20.0 16.0 36.0 44 8.0 21°
Technical data
Part No. Max. radial compressive strength Max. axial compressive strength Weight
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
ECLM-08-04-HD 393 28 197 13 2.0
ECLM-10-05-HD 565 34 281 17 3.1
ECLM-12-06-HD 787 39 393 19 3.8
ECLM-20-08-HD 1349 74 674 37 12.0
*W300 is the European material equivalent for iglide® L280.
Tolerance compensation
Dimensional E series
Self-aligning bearing
b2
Inner-Ø [mm]
with flange
d2 min.
d2 max.
Metric
d1
Material:
d3 C Housing: igumid G ➤ Page 1373
B Spherical ball: iglide® L280 (W300)*
Other ball stud materials on request
Dimensions [mm]
Part Number Max. radial Max. axial Weight
compressive strength compressive strength
Short term Long term Short term Long term
[lbs] [lbs] [lbs] [lbs] [g]
EGFM-08 T SL31) 250 124 34 17 0.9
EGFM-10 T 427 214 50 25 2.4
EGFM-12 T 560 280 61 30 3.0
EGFM-16 T 1350 675 135 67 6.6
EGFM-20 T 2020 1012 180 90 11.1
EGFM-25 T 3147 1574 630 315 19.0
EGFM-30 T 3822 1910 675 337 24.0
Technical data
Part No. d1 d2 d2 d3 C B b2 Housing Max.
min. max. min. max. pivot angle
EGFM-08 T SL31) 8 (H10) 15.8 16.5 18 5.0 6 1.1 15.8 16.2 11°
EGFM-10 T 10 20.8 21.6 26 6.0 9 1.0 20.8 21.2 24°
EGFM-12 T 12 22.8 23.6 28 7.0 10 1.0 22.8 23.2 21°
EGFM-16 T 16 29.8 30.6 35 9.5 13 1.5 29.8 30.2 21°
EGFM-20 T 20 34.8 35.6 42 12.0 16 2.0 34.8 35.2 18°
EGFM-25 T 25 41.8 42.6 50 16.0 20 2.0 41.8 42.2 16°
EGFM-30 T 30 46.8 47.6 55 18.0 22 2.0 46.8 47.2 13°
31)
Spherical ball made from iglide J®
x
Double joint turned 90° available
Dimensional E series
on request
Inner-Ø [mm]
Double joint
Pitch X
Metric
b
d2
Material:
Housing: igumid G ➤ Page 1373
Spherical ball: iglide® L280 (W300)*
Other ball stud materials on request
d1d1
Order key
Type Size Options
d3d3
K DG M - 06 - A - SR - J
x
x
Tube material
Inner-Ø [mm]
Double joint
d2d2 CC
Version A Version B
Pitch X
BB
Metric
Ball diameters 6, 8, 10 and 12 mm Material:
Individual center dimensions and lengths Housing: igumid G ➤ Page 1373
Individual alignment of the bearing position Spherical ball: iglide® L280 (W300)*
Other options available see below
Tube: galvanized or stainless steel
Dimensions [mm]
Part No. d1 d2 d3 X B C Max.
pivot angle
E 10 min.
KDGM-06-A-SR-J £ 32)
6.0 20.0 6.0 72.0 9.0 7.0 40°
KDGM-08-A-SR-J £ 32)
8.0 24.0 8.0 84.0 12.0 9.0 35°
KDGM-10-A-SR-J £ 32) 10.0 30.0 10.0 96.0 14.0 10.5 35°
KDGM-12-A-SR-J £ 32) 12.0 34.0 12.0 108.0 16.0 12.0 35°
32)
Please add the required center distance in mm
Order example, KDGM-06-A-SR-J, 100 : Double joint with 06 mm inner diameter, version A, tube material
made of steel, spherical ball made of iglide® J, center distance 100mm
Order key
Type Size Options
W DG M - 06 - A - SR - J
Tube material
(A, B, C or D)
Double joint
Metric
Angle
Version A Version B Version C Version D
B B d2 d2 Material:
Housing: igumid G ➤ Page 1373
d1
d1
SR = Steel J = iglide® J
ER = Stainless steel J4 = iglide® J4
R = iglide® R
EK = Stainless steel
d1
d1
Dimensions [mm]
Part No. d1 d2 d3 X B h1 h2 S1 R Max.
min. Width across flats pivot angle
WDGM-05-A-SR-SZ £ 32) M5 12.8 8.0 74.0 10.8 4.6 19.2 SW8 6.4 23°
WDGM-06-A-SR-SZ £ 32)
M6 14.8 10.0 80.0 12.3 6.1 23.5 SW9 7.4 25°
WDGM-08-A-SR-SZ £ 32)
M8 19.3 12.0 80.0 16.2 5.9 29.5 SW12 9.7 24°
WDGM-10-A-SR-SZ £ 32) M10 33)
19.3 12.0 80.0 16.2 7.9 36.0 SW14 9.7 24°
32)
Please add the required center distance in mm
Housing’s size 8 with a special M10 stud, available only in metal
33)
Order example, WDGM-05-A-SR-SZ, 100 : Double joint with 05 ball stud thread, version A, tube material
made of steel, ball stud made of steel, center distance 100mm
• Easy to install
• Compensation of misalignment errors
• Compensation of edge loads
• Very good friction and wear properties
853
igubal®
spherical
thrust igubal® Spherical Thrust Bearing
bearing
igubal® self-aligning spherical thrust bearings are very easy to fit and help to compensate misalignment errors and prevent
edge loads.
max. +176°F
F
min. –22°F
1 type
mm Ø 5 to 20 mm
Mechanical properties
igubal® self-aligning spherical thrust bearings are very easy to fit and
help to compensate for alignment errors and prevent edge loads.
The housing pad is made of the impact resistant, thermoplastic
composite material igumid G. The spherical washer is made of
the iglide® L280 (W300) plain bearing material. This combination
provides exceptionally good friction and wear properties.
Loads
Installation
Product range
Order key
Type Size
SA M - 04
Dimensional E series
Based on 1/16”
Inner-Ø [inch]
Spherical washer
Inch
R1-Ball
Material:
h1h1
Housing pad
h2h2
d3
d3
d2
d2
857
igubal®
spherical
balls
igubal® Spherical Balls
Every iglide® material has its own special properties, which determines the suitability for your special applications and
requirements. Today, igus® offers spherical bearings from iglide® materials L280 (W300)* as a standard, J, J4, R, RN248,
UW and T500 (X)*. The spherical ball for metallic bearing housings are available for housing numbers 203 to 210.
Self-lubricating, maintenance-free
When to use it?
If you need maintenance free material
When dimensional E series and K components should
be fitted
If different iglide® materials should
be tested
Corrosion-resistant If high compressive strength is required
If high elasticity is required
Tolerances
The tolerance of the inner diameter is E10. The shaft
High elasticity tolerance should be included between h6 and h9.
A variety of materials
2 types
Ø 3/16 to 1 inch
8 types
mm Ø 2 to 50 mm
*W300 is the European material equivalent for iglide® L280, X is the European equivalent material for iglide® T500
Standard Low-cost
iglide® L280 (W300)* iglide® R
Detectable
For metallic bearing housings
iglide® RN248
W ... I - 08 - 04
d1
dn
dk
°
30
+194ºF
Inner-Ø [mm]
K = K series
E = E series
d1
dn
dk
–40ºF
Width
°
30
Inch
Dimensions [inch] Dimensions [inch]
Part No. d1 dn dK B Weight Part No. d1 dn dK B Weight
[E10] [g] [E10] [g]
WKI-03 .1875 .307 .444 .312 0.6 WEI-03 .1875 .354 .402 .1900 0.3
WKI-04 .2500 .354 .516 .375 1.0 WEI-04 .2500 .314 .402 .2500 0.3
WKI-05 .3125 .447 .625 .437 1.7 WEI-05 .3125 .415 .520 .3125 0.7
WKI-06 .3750 .504 .718 .500 2.3 WEI-06 .3750 .506 .630 .3750 1.3
WKI-07 .4375 .601 .828 .562 3.5 WEI-07 .4375 .581 .709 .4063 1.6
WKI-08 .5000 .700 .938 .625 5.0 WEI-08 .5000 .581 .709 .4063 2.6
WKI-10 .6250 .838 1.125 .750 8.2 WEI-10 .6250 .802 .945 .5000 3.1
WKI-12 .7500 .978 1.312 .875 12.5 WEI-12 .7500 .951 1.138 .6250 5.9
WKI-16 1.0000 1.269 1.750 1.375 31.7 WEI-16 1.0000 1.180 1.398 .7500 9.2
W ... M - 08 - 04
d1
dn
dk
°
30
Dimensional series
+194ºF
Inner-Ø [mm]
d1
–40ºF
dn
dk
Metric
Width
°
30
R E I - 04
d1
dn
dk
°
30
Dimensional E series
B
+194ºF
Inner-Ø [mm]
iglide® R
d1
–40ºF
dn
dk
°
30
Inch
iglide® R - low friction values,
low cost, low moisture
absorption
Dimensions [inch]
Part No. d1 dn dK B Weight
[E10] [g]
REI-03 .1875 .354 .402 .1900 0.3
REI-04 .2500 .314 .402 .2500 0.3
REI-05 .3125 .415 .520 .3125 0.7
REI-06 .3750 .506 .630 .3750 1.3
REI-07 .4275 .581 .709 .4063 1.6
REI-08 .5000 .581 .709 .4063 2.6
REI-10 .6250 .802 .945 .5000 3.1
REI-12 .7500 .951 1.138 .6250 5.9
REI-16 1.0000 1.180 1.398 .7500 9.2
[E10] [g]
REM-05-06 5.00 8.00 10.20 6.00 0.4
Inner-Ø [mm]
K = K series
E = E series
Width
X ... M - 06 - 08
d1
dn
dk
°
30
Dimensional series
B
Inner-Ø [mm]
K = K series
E = E series
Metric
Width
–148ºF
d1
dn
dk
°
30
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
XKM-10-04 10.00 12.90 19.10 14.00 2.9
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
XEM-05-06 5.00 8.00 10.30 6.00 0.4
XEM-06-06 6.00 8.00 10.20 6.00 0.4
XEM-08-08 8.00 10.00 13.20 8.00 0.8
XEM-10-09 10.00 13.00 16.00 9.00 1.3
XEM-12-10 12.00 15.00 18.00 10.00 1.6
J ... M - 05 - 08
d1
dn
dk
°
30
Dimensional series
B
+194ºF
Inner-Ø [mm]
K = K series
E = E series
iglide® J
d1
dn
dk
Metric
–58ºF
Width
°
30
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
JKM-03-06 3.00 5.10 8.10 6.00 0.3
JKM-05-08 5.00 7.70 11.30 8.00 0.7
JKM-06-09 6.00 8.90 12.80 9.00 1.0
JKM-08-12 8.00 10.30 15.90 12.00 1.9
JKM-10-14 10.00 12.90 19.00 14.00 3.1
JKM-12-16 12.00 15.40 22.10 16.00 4.7
JKM-16-21 16.00 19.30 28.40 21.00 9.4
JKM-20-25 20.00 24.30 35.10 25.00 17.6
JKM-25-31 25.00 29.50 42.80 31.00 31.6
JKM-30-37 30.00 34.80 51.20 37.00 53.0
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
JEM-04-05 4.00 6.25 8.30 5.00 0.3
JEM-05-06 5.00 8.00 10.20 6.00 0.4
JEM-06-06 6.00 8.00 10.20 6.00 0.4
JEM-08-08 8.00 10.00 13.30 8.00 0.8
JEM-10-09 10.00 13.00 16.10 9.00 1.3
JEM-12-10 12.00 15.00 18.10 10.00 1.7
JEM-15-12 15.00 18.00 22.00 12.00 2.9
JEM-16-13 16.00 19.50 24.10 13.00 3.9
JEM-17-14 17.00 20.00 25.20 14.00 4.1
JEM-20-16 20.00 24.00 29.10 16.00 6.4
JEM-25-20 25.00 29.00 35.60 20.00 11.5
JEM-30-22 30.00 34.00 40.90 22.00 14.5
Order key
Type Size
B J K M - 35 - 49
Dimensional K series
+194ºF
d1
dn
dk
°
30
Inner-Ø [mm]
–58ºF
iglide® J
Metric
Width
iglide® J - Low moisture absorption
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
JKM-35-49 35)
35.00 44.50 66.30 49.00 75.5
JKM-40-49 40.00 44.50 66.30 49.00 54.5
JKM-45-60 35)
45.00 56.50 82.40 60.00 125.1
JKM-50-60 50.00 56.50 82.40 60.00 92.1
35)
Diameter reduced by means of a plain bearing
Dimensional K series
30
Inner-Ø [mm]
Split ball
iglide® J
Metric
J4 ... M - 08 - 08
d1
dn
dk
°
30
Dimensional series
+194ºF
Inner-Ø [mm]
K = K series
E = E series
iglide® J4
–58ºF
d1
dn
dk
Metric
Width
°
30
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
J4KM-10-14 10.00 12.90 19.10 14.00 3.1
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
J4EM-04-05 4.00 6.25 8.25 5.00 0.3
J4EM-05-06 5.00 8.00 10.20 6.00 0.4
J4EM-06-06 6.00 8.00 10.20 6.00 0.4
J4EM-08-08 8.00 10.00 13.30 8.00 0.8
J4EM-10-09 10.00 13.00 16.00 9.00 1.3
J4EM-12-10 12.00 15.00 18.00 10.00 1.7
J4EM-15-12 15.00 18.00 22.00 12.00 2.9
J4EM-16-13 16.00 19.50 24.00 13.00 3.9
J4EM-17-14 17.00 20.00 25.10 14.00 4.1
J4EM-20-16 20.00 24.00 28.90 16.00 6.4
J4EM-25-20 25.00 29.00 35.50 20.00 11.5
J4EM-30-22 30.00 34.00 40.90 22.00 14.5
UW E M - 08 - 08
d1
dn
dk
°
–58ºF
30
Dimensional series
Inner-Ø [mm]
E = E series
iglide® UW
Metric
Width
iglide® UW - For underwater use
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
UWEM-16-13 16.00 19.50 23.80 13.00 4.0
UWEM-20-16 20.00 24.00 28.80 16.00 6.5
UWEM-25-20 25.00 29.00 35.30 20.00 11.6
UWEM-30-22 30.00 34.00 40.50 22.00 15.2
Order key
Can be combined with all E series housings
Sizes 8 to 20 mm Type Size
Preloaded
Totally clearance free in unloaded state
J4 V E M - 08 - 08
Dimensional E series
B B
Inner-Ø [mm]
+194ºF
0.5 (6x)
0.5 (6x)
Preloaded
iglide® J4
Metric
–58ºF
Width
d1
d1
dk
dk
iglide® J4 - low moisture absorption,
low friction values
Dimensions [mm]
Part No. d1 dK B Weight
[E10] [g]
J4VEM-08-08 8 13.20 8.00 0.7
J4VEM-10-09 10 16.10 9.00 1.2
J4VEM-12-10 12 18.10 10.00 1.5
J4VEM-16-13 16 24.10 13.00 3.7
J4VEM-20-16 20 29.10 16.00 6.2
RN248 E M - 08 - 08
d1
dn
dk
°
30
Dimensional series
+194ºF
iglide® RN248
Inner-Ø [mm]
K = K series
E = E series
–58ºF
d1
dn
dk
Metric
Width
°
30
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
RN248KM-06-09 6.00 8.90 12.80 9.0 1.0
Dimensions [mm]
Part No. d1 dn dK B Weight
[E10] [g]
RN248EM-05-06 5.00 8.00 10.30 6.00 0.4
RN248EM-06-06 6.00 8.00 10.20 6.00 0.4
RN248EM-08-08 8.00 10.00 13.20 8.00 0.8
RN248EM-10-09 10.00 13.00 16.10 9.00 1.3
RN248EM-12-10 12.00 15.00 18.10 10.00 1.6
d (E10)
D
Dimensions [mm]
Part No. Housing No. d D B Max. static compressive strength
[E10] radial [kN] axial [kN]
Made of iglide J, low friction (material information ➤ Page 115
®
873
igubal®
detectable igubal® Pillow Block
igubal® bearings can be found quickly in case of misuse or crash of the system through metal detectable material. Even the
smallest fragment can be found by metal detectors.
Detectable
When to use it?
When particles should be detectable
When maintenance free materials are required
Resistant to dust and dirt
If dimensional K series and E series should be used
If high pressure resistance is required
Self-lubricating and If high elasticity is requested
maintenance-free
Lightweight
max. +176°F
F
min. –22°F
4 types
mm Ø 4 to 12 mm
From stock
Integrated lock nut for easy For small space requirement High strength
assembly E series under impact loads
K series EBRM-…-DT E series
KBRM-…-CL-DT EBLM-…-DT GERM-…-DT
KBLM-…-CL-DT GELM-…-DT
K B ... M - 06 - CL - DT
d1
d1
h2 h3
h3
Dimensional K series
2nd generation
l1
l1
Inner-Ø [mm]
Detectable
m
m
Thread
d3 d3
Metric
W W
Material:
Smooth design does not trap dirt Housing: RN246 ➤ Page 1375
Spherical ball: RN248KM
Compensation for shaft misalignment
Lightweight
Excellent corrosion resistance
Dimensional K series according to standard DIN ISO 12240
Dimensions [mm]
Part No. d1 d2 d3 W B C1 h3 h1 h2 l1 l2 m max.
Right-hand thread Left-hand thread [E10] pivot
angle
Technical data
Part No. Max. static Max. static Min. thread Max. torque Max. torque Weight
tensile strength radial load depth strength through ball
Short Long Short Long Inner Standard
Right-hand thread Left-hand thread Thread
term term term term threading without MH
[lbs] [lbs] [lbs] [lbs] [mm] [ft lbs] [ft lbs] [g]
E B ... M - 06 - DT
d1
d1
Inner-Ø [mm]
l1
l1
Detectable
Thread
d3
d3
Metric
d4
d4
WW
d5
d5
Material:
Smooth design has no dirt traps Housing: RN246 ➤ Page 1375
Spherical ball: RN248EM
Clip in ball
Compensation for shaft misalignment
Lightweight
Excellent corrosion resistance
Dimensions [mm]
Part No. d1 d2 d3 d4 d5 C1 B h1 l1 l2 W
Maximum
Right-hand thread Left-hand thread [E10]
pivot angle
Technical data
Part No. Max. static Max. static Min. thread Max. torque Max. torque Weight
tensile strength radial load depth strength through ball
Short Long Short Long Inner Standard
Right-hand thread Left-hand thread Thread
term term term term threading without MH
[lbs] [lbs] [lbs] [lbs] [mm] [ft lbs] [ft lbs] [g]
G E ... M - 04 - DT - F
g
I2
I2
h1
h1
I1
Inner-Ø [mm]
Fine Thread
d2
Detectable
d2
Clevis joint
a1
d3
a1
d3
Thread
Metric
Detectable
a2 a2
Resistant to dust and dirt
Material:
Self-lubricating and maintenance-free
RN246 ➤ Page 1375
Vibration dampening
Lightweight
Dimensions [mm]
Part No. d1 g a1 a2 b1 d2 d3 I2 h1 l1
H9 h11 +0.3 +0.3 B13 Thread +0.3 +0.5 +0.3 +0.2
Right-hand thread Left-hand thread –0.16 –0.16 tolerance –0.3 –0.5 –0.3 –0.2
6H
Technical data
Part No. Max. static Max. static Weight
tensile strength radial load
Right-hand thread Left-hand thread Short term Long term Short term Long term
[N] [N] [N] [N] [g]
d2
b
Type Size Version
a
G E F M - 04 - DT
Dimensional E series
h1
l1
Inner-Ø [mm]
Detectable
Clevis joint
Metric
Detectable
Resistant to dust and dirt
Self-lubricating and maintenance-free Material:
Vibration dampening RN246 ➤ Page 1375
Lightweight
Dimensions [mm]
Part No. d1 d2 a b c l1 h1 l2 Weight
±0.5 [g]
GEFM-04-DT 4 8 9.5 10.5 8 19 15 4.5 0.5
GEFM-05-DT 5 10 14 15.5 8 27 23 6.5 1.1
GEFM-06-DT 6 10 14 15.5 8 27 23 6.5 1.2
GEFM-08-DT 8 14 19 21.0 11 35.5 30 8.0 2.8
GEFM-10-DT 10 18 23 25.5 14 45 38 10.0 5.0
GEFM-12-DT 12 20 28 31.0 16 53 45 12.0 8.3
Order key
G E ... M F - 04 - DT - F
Inner-Ø [mm]
Fine Thread
Detectable
Clevis joint
Thread
Detectable
Metric
Resistant to dust and dirt
Maintenance free and lubrication free
Material:
Vibration dampening
RN246 ➤ Page 1375
Lightweight
Technical data
Part No. Max. static Max. static Weight
tensile strength radial load
Right-hand thread Left-hand thread Short term Long term Short term Long term
[N] [N] [N] [N] [g]
GERMF-04-DT GELMF-04-DT 79 39 39 20 1.3
GERMF-05-DT GELMF-05-DT 142 71 39 20 3.8
GERMF-06-DT GELMF-06-DT 205 102 47 24 3.9
GERMF-08-DT GELMF-08-DT 330 165 102 51 9.1
GERMF-10-DT GELMF-10-DT 472 236 126 63 18.2
GERMF-10-DT-F GELMF-10-DT-F 472 236 126 63 18.2
GERMF-12-DT GELMF-12-DT 551 275 142 71 28.6
GERMF-12-DT-F GELMF-12-DT-F 551 275 142 71 28.6
Individual components: Clevis joint GERM-DT and spring-loaded fixing clip GEFM-DT
➤
Linear technology,
lead screw technology
and drive technology
...
...plastics
DryLin® - Application examples
Typical industries and application areas
l Packaging machinery
l Lab automation
l Medical equipment
l Marine
l In-cab applications (construction/agriculture)
l Aircraft interiors
l Maintenance-free l Dry-running
l Wear-resistant l Suited for short-stroke applications
l Insensitive to shocks and vibrations l High static load capacity
l Corrosion resistant l High speeds and accelerations possible
l Resistant to dirt, dust and humidity l Self-lubricating
l Low coefficients of friction l Very quiet operation
l Weight reduction l Low magnetism
dB dB Low noise
DryLin The quiet operation of DryLin® linear bearings is a benefit of the
Ball bearing
®
n Speed Speed
Figure 01: Comparison of noise development
Permitted speeds/accelerations
With low loads DryLin ® has been tested at speeds up to 49
fps (10 m/s). The maximum permissible speed is related to
the bearing load - the lower the load the higher the permissi-
ble speed. Since DryLin® does not rely on complicated rolling
elements, but instead on specially engineered, low wear, low
friction glide strips, extremely high speeds and accelerations are
now possible. This means that DryLin® is ideal for applications
where cycle and accelerations must be increased.
More significant than the maximum speed is the average speed-
per-cycle time. Therefore, in order to calculate the suitability of a
particular DryLin® system, the average surface speed should be
determined. In applications with intermittent cycles, the highest
average surface speed is significant; this is an average taken
over a 10-30 minute time period
The use of DryLin® S hard anodized aluminum as a shaft material
decreases the operating temperature in the bearing system due
to its thermal conductivity and micro-finish. It is recommended
Thermal conductivity [W / m · K] for most applications with short-strokes or high cycles when
Aluminum 235 using the iglide® J/J200 material liners. It is the material we have
Unalloyed steel 48 - 58 designed for use with all of our profile guides as well.
High-alloyed steel 15
Chemical resistance
Extreme application conditions in the offshore industry iglide® J is resistant to weak acids, diluted alkalis as well as to fuels
and all types of lubricants. The intensive cleaning of machines with
standard commercial cleaning agents, even in the food industry, is
no problem for DryLin® guides. For applications in environments with
more aggressive cleaning agents, the use of the DryLin® R bearings
with iglide® T500 liners is recommended. The resistance of linear
bearing systems is equally dependent on the shaft or rail material.
For the highest resistance to chemicals, a 304 or 316 stainless shaft
material is optimal.
Operating temperatures
Sliding elements made from iglide® J and J200 can be used in the
Filling machine, Krones AG, Rosenheim temperature range between -40°F and +194°F (-40 and +90°C). In
applications with aluminum shafts or rails, distinctly higher loads and
speeds can be attained due to the excellent thermal conductivity.
Sliding elements made of iglide® T500 can be used in temperatures
ranging from -238°F to 482·F (100°C to +250°C).
Resistance to dirt
Applications exposed to coarse dirt and sand are possible since
debris is wiped away by the sliding of the plain bearing. The lack
of required external lubrication means that seals are not required
as there is no grease or oil to attract dust and dirt.
The iglide® T500 (X)* material in heavy-duty use under high
temperatures in foundries
The "all-rounder" – The specialist – The extreme – The marathon runner – FDA compliant –
iglide® J iglide® J200 iglide® T500 (X)* iglide® E7 iglide® A180
Aluminum, Hardened stainless steel Steel
Optimal shaft material(s) all shaft materials
hard anodized Hard chromed plated steel stainless steel shaft
all shaft materials
-40°F to +194°F -40°F to +194°F -148°F to +482°F -40°F to +194°F -40°F to +194°F
Application temperature (-40°C to +90°C) (-40°C to +90°C) (-100°C to +250°C) (-40°C to +90°C) (-40°C to +90°C)
Aluminum, Steel hard Steel
Best coefficient of friction with Steel shaft
hard anodized chrome-plated stainless steel shaft
Stainless steel shaft
Aluminum, hard Aluminum, Hardened Steel
Maximum life time anodized hard anodized stainless steel stainless steel shaft
Stainless steel shaft
Permissible stat. surface pressure 35 MPa 23 MPa 150 MPa 18 MPa 28 MPa
Moisture absorption 1.3% weight 0.7% weight 0.5% weight < 0.1% weight 0.2% weight
iglide® J200:
l Completely maintenance-free
l Extremely high service life on hard-anodized aluminum
l Low coefficients of friction with hard-anodized aluminum
l Excellent wear resistance with anodized aluminum
➤ More about iglide® J200 ➤ Page 313
Filling-shoe mechanism in a compaction unit Stop dog system of a sliding table panel saw
Fitness equipment: Seat height adjustment for bench Adjustment of kitchen worktop
press
Linear technology-
...
...plastics
DryLin® linear technology - Advantages
Maintenance-free DryLin®
Superior operating
performance by combining iglide®
linear guide systems
bearing materials and anodized
rails with round shaft profiles DryLin® is a range of maintenance-free, self-lubricating
linear slide bearings consisting of four main product lines.
Principal features, in addition to zero maintenance, are
strength and resistance to external influences such as
Corrosion resistant corrosion, moisture, chemicals, heat and impact.
Lightweight due to
the use of plastics and
aluminum
Maintenance-free due to
integrated lubricants
Properties
Size Self-lubricating Same Profile rails Round Square Single Complete Hybrid
and quiet dimensions as shafts profiles housing carriage linear bearing
ball bearings bearing sliding and
rolling
DryLin® W 5
DryLin N
®
4
DryLin® Q 3
DryLin T
®
4
DryLin® T mini 4
DryLin R
®
12
Special criteria
Loads For robust Resistant Compact, Particularly Torque Torsionally Unsupported
> 100 kg requirements to dirt space saving light weight resistant stable installation
DryLin® W Ì Ì ÌÌ Ì Ì Ì ÌÌ Ì
DryLin® N Ì ÌÌ ÌÌ Ì
DryLin Q
®
Ì Ì Ì ÌÌ Ì ÌÌ
DryLin® T Ì Ì Ì Ì Ì
DryLin T mini
®
Ì ÌÌ ÌÌ Ì
DryLin® R ÌÌ ÌÌ ÌÌ Ì
Technical options
Manual Automatic Automatic Floating bearing Manual with with with
adjustable adjustable preload function clamp measuring lead screw timing
bearing bearing system drive belt drive
clearance clearance
DryLin® W Ì Ì Ì Ì Ì Ì
DryLin® N ÌÌ Ì Ì Ì
DryLin Q
®
Ì Ì Ì
DryLin® T Ì Ì Ì Ì
DryLin T mini
®
Ì Ì Ì
DryLin® R Ì Ì
Application areas
Stainless steel Temperatures Chemical FDA compliant Cleanroom and Door/control Camera 3D-print
components above 194°F resistant ESD panel slider components
(90°C) adjustments
DryLin® W ÌÌ ÌÌ ÌÌ ÌÌ Ì ÌÌ ÌÌ ÌÌ
DryLin® N Ì Ì Ì Ì ÌÌ
DryLin Q
®
Ì
DryLin® T Ì ÌÌ
DryLin T mini
®
Ì Ì ÌÌ
DryLin® R ÌÌ ÌÌ ÌÌ ÌÌ Ì ÌÌ
Ì suitable ÌÌ particularly suitable
➤ www.igus.com/drylin-expert
Load F (lbs)
application, and is available at www.igus.com. It will give warning if
the load capacity of a certain bearing is exceeded. 10
0.3 3.5 33
Speed v (ft/s)
DryLin® T 25 DryLin® N 27 DryLin® R 25 DryLin® W
F = total of loads per rail/shaft
Series Max Static Load
F x V values of comparable DryLin® systems
DryLin R 20,000 lbs
DryLin T 3,140 lbs
DryLin W 719 lbs
DryLin N 220 lbs
Permissible Speeds
With low loads DryLin® has been tested at speeds up to 49 fps (15 m/s). The maximum permissible speed is related to the bearing
load - the lower the load the higher the permissible speed. Since DryLin® does not rely on complicated rolling elements, but instead
on specially engineered, low wear, low friction glide strips, extremely high speeds and accelerations are now possible. This means
that DryLin® is ideal for applications where cycle and accelerations must be increased.
More significant than the maximum speed is the average speed-per-cycle time. Therefore, in order to calculate the suitability of a
particular DryLin® system, the average surface speed should be determined. In applications with intermittent cycles, the highest
average surface speed is significant; this is an average taken over a 10-30 minute time period
The use of DryLin® S hard anodized aluminum as a shaft material decreases the operating temperature in the bearing system due
to its thermal conductivity and micro-finish. It is recommended for most applications with short-strokes or high cycles when using
the iglide® J/J200 material liners. It is the material we have designed for use with all of our profile guides as well.
Eccentric Forces
Floating Fixed Floating Fixed 2x The 2 : 1 Rule
When using linear plain bearings it is important to
ensure that the acting forces follow the 2:1 Rule
(see drawing). If either the load or the drive force
1x (F) is greater than twice the bearing length (1X),
then a binding or interrupted motion may occur.
If the location of the drive force or load cannot be
changed, simply increase the distance between
Figure 02: Automatic compensation of Figure 03: The 2:1 rule the bearings, or create a counterbalance to move
parallelism errors
the center-of-gravity back within the 2 to 1 ratio.
Standard Version Horizontal Float “LLZ” Vertical Float “LLY” DryLin® W can also
alleviate edge pressure
Ideal for non-flat, even
surfaces
DryLin ® R linear plain bearings in the 03 Design Series are In order to compensate for parallelism errors between two
self-aligning and offer great advantages in applications with shafts, the outer diameter is designed to be smaller than the
parallel shafts. They are able to compensate for alignment and housing bore diameter by 0.2 - 0.3 mm (depending on the
parallelism errors and should be used on the shaft located size). With the use of mounted O-rings, these bearings have
furthest from the drive mechanism. an elastic bearing seat.
The design provides a raised spherical area on the outer Compensation for angle errors
diameter of the aluminum adapter for self-alignment. Load Series RJUI/RJUM/OJUI/OJUM-03 ±0.5°
capacity is the same as the fixed version. Series RJUM-06-LL/OJUM-06-LL ±3.5°
The spherical DryLin® adapters can com- With built in clearances and the use of The self-aligning DryLin ® R bearings of
pensate for alignment errors. A hard-an- O-rings, the self-aligning DryLin® R bearings the 06 LL design series can compensate
odization protects the aluminum adapter of the 03 Design Series can compensate for parallelism errors up to ± .12” (3mm).
from wear. parallelism errors.
Rail
Fixed
bearing
Fixed Floating
bearing bearing VF-Y
Carriage
Floating
Fixed bearing bearing HF
Floating
bearing HF
All DryLin® guide systems are clearly qualified for clean room 40-02 can be classified as "level 1" (Highest rank). See Fraunhofer
applications. The differentiation between the various clean room IPA Report No.: IG 0308-295 73.
classes is only dependent on load and speed of the application.
The combination of iglide® J and hard Linear guide system DryLin® TK-01-25-02
anodized aluminum is classified as level "For the linear guide system DryLin®
1 in the ESD compatibility according to TK-01-25-02 by igus® GmbH, it is pos-
SEMI E78-0998 (Highest rank). sible, on the calculations of the likeli-
hood of violation of threshold values of
The following DryLin guides from igus
® ®
the detection sizes 0.2 μm, 0.3 μm, 0.5
were tested: N40, W10, T25 and T30. μm, and 5 μm with motion speed of v
See below for detailed results. =1 m/s, to clearly derive suitability for
clean rooms classified as ISO Class 5 according to DIN EN ISO
Linear guide system DryLin TK-10-30-01
®
14644-1."
"For the linear guide system DryLin® TK-10-30-01 by igus® GmbH, The measurement results of the ESD compatibility according to
it is possible, on the calculations of the likelihood of violation of SEMI E78-0998 show that the linear guide system DryLin® TK-01-
threshold values of the detection sizes 0.2 μm, 0.3 μm, 0.5 μm, 25-02 can be classified as "level 1" (Highest rank).
and 5 μm with motion speed of v = 0.1 m/s, to clearly derive
suitability for clean rooms classified as ISO Class 3 according to Linear guide system DryLin® WK-10-40-15-01
DIN EN ISO 14644-1." "For the linear guide system DryLin® WK-10-40-15-01 by igus®
GmbH, it is possible, on the calculations of the likelihood of vio-
Linear guide system DryLin NK-02-40-02
®
lation of threshold values of the detection sizes 0.2 μm, 0.3 μm,
"For the linear guide system DryLin® NK-02-40-02 by igus® GmbH, it 0.5 μm, and 5 μm with motion speed of v =1 m/s, to clearly derive
is possible, on the calculations of the likelihood of violation of thresh- suitability for clean rooms classified as ISO Class 6 according to
old values of the detection sizes 0.2 μm, 0.3 μm, 0.5 μm, and 5 μm DIN EN ISO 14644-1."
with motion speed of v =1 m/s, to clearly derive suitability for clean The measurement results of the ESD compatibility according to
rooms classified as ISO Class 6 according to DIN EN ISO 14644-1." SEMI E78-0998 show that the linear guide system DryLin® WK-10-
The measurement results of the ESD compatibility according to 40-15-01 can be classified as "level 1" (Highest rank).
SEMI E78-0998 show that the linear guide system DryLin NK-02- ®
See Fraunhofer IPA Report No.: IG 0308-295 74.
➤ Page 920 ➤ Page 921 ➤ Page 922 ➤ Page 923 ➤ Page 924 ➤ Page 925
➤ Page 933 ➤ Page 934 ➤ Page 935 ➤ Page 936 ➤ Page 937 ➤ Page 938
➤ Page 959 ➤ Page 959 ➤ Page 961 ➤ Page 961 ➤ Page 963 ➤ Page 963
JUI / JUIO Liner J200UI E7UI / E7UIO Liner TUI / TUIO RJI / RJIP RJUI
made from iglide® J J200UIO Liner made from iglide® E7 (XUI / XUIO) Liner made from iglide® J Closed anodized
open/closed made from iglide® J200 open/closed made from iglide® T500 (X)* RJI - standard, aluminum adapter
Standard (-01) open/closed Standard (-01) open/closed RJIP - Low clearance Standard (-01)
Low clearance (-20) Standard (-01) Standard (-01) Low clearance (-21)
Self aligning (-03)
➤ Page 1004 ➤ Page 1008 ➤ Page 1010 ➤ Page 1012 ➤ Page 1014 ➤ Page 1016
➤ Page 926 ➤ Page 928 ➤ Page 929 ➤ Page 930 ➤ Page 931 ➤ Page 932
➤ Page 946 ➤ Page 947 ➤ Page 948 ➤ Page 948 ➤ Page 949
➤ Page 1019 ➤ Page 1021 ➤ Page 1023 ➤ Page 1025 ➤ Page 1028 ➤ Page 1030
➤ Page 1033 ➤ Page 1036 ➤ Page 1037 ➤ Page 1038 ➤ Page 1039 ➤ Page 1040
JUM / JUMO Liner JUM / JUMO Liner J200UM E7UM / E7UMO Liner TUM / TUMO TUM / TUMO
made from iglide® J made from iglide® J J200UMO Liner made from iglide® E7 (XUM / XUMO) Liner (XUM / XUMO) Liner
open/closed long (-01) closed design, made from iglide® J200 open/closed made from iglide® T500 (X)* made from iglide® T500 (X)*
Low clearance (-20) Short (-02) open/closed Standard (-01) open/closed open/closed
Low clearance, (-22) Standard (-01) Standard (-01) Short design (-02)
➤ Page 1042 ➤ Page 1046 ➤ Page 1048 ➤ Page 1050 ➤ Page 1052 ➤ Page 1054
➤ Page 1066 ➤ Page 1067 ➤ Page 1068 ➤ Page 1071 ➤ Page 1074 ➤ Page 1075
➤ Page 1082 ➤ Page 1083 ➤ Page 1084 ➤ Page 1085 ➤ Page 1086 ➤ Page
RGAS OGAS
Linear housing Linear housing
short, closed design short, open design
➤ Page 1055 ➤ Page 1056 ➤ Page 1058 ➤ Page 1061 ➤ Page 1062 ➤ Page 1063
➤ Page 1076 ➤ Page 1077 ➤ Page 1078 ➤ Page 1079 ➤ Page 1080 ➤ Page 1081
➤ Page 1088 ➤ Page 1089 ➤ Page 1090 ➤ Page 1091 ➤ Page 1092 ➤ Page 1093
➤ Page 1102 ➤ Page 1104 ➤ Page 1106 ➤ Page 1110 ➤ Page 1111 ➤ Page 1113
➤ Page 1122 ➤ Page 1123 ➤ Page 1124 ➤ Page 1125 ➤ Page 1126 ➤ Page 1127
Accessories
Supports made from plastic,
end caps for section rail, linear
construction kit
➤ Page 1128
➤ Page 1134 ➤ Page 1135 ➤ Page 1136 ➤ Page 1136 ➤ Page 1137 ➤ Page 1138
➤ Page 1141 ➤ Page 1143 ➤ Page 1146 ➤ Page 1150 ➤ Page 1151 ➤ Page 1152
Self-lubricating linear
Tribologically-optimized systems
with iglide plastic bearing liners system - DryLin W ®
Corrosion resistant nating the need for both shaft alignment and bearing assembly. All
DryLin® W systems are available with our enhanced J200 liners,
which reduce friction and optimize bearing life.
Clean, no external
lubrication is required
Component parts:
Single rails and bearings
l Liners made from iglide® J200/J/T500/E7/A180
l Housings made from die-cast zinc, aluminum or stainless steel
l Turn-to-fit function for clearance adjustment optional
l Rail material: hard-anodized aluminum or stainless steel (316L)
l Single rails for optimum design flexibility (individual/parallel/
diagonal designs possible)
l The hard anodize surface of DryLin® rails and shafts is integral to
the tribology of the bearing system - therefor variations in color,
and superficial crazing under the anodic layer may occur
➤ Page 920
Assembled systems:
Complete carriages and double-rail profiles
l Multiple carriage lengths and widths
l Pre-assembled carriages available
l One-piece carriages for quick assembly available
l Rail material: hard-anodized aluminum
l Rigid double-shaft profile
l Double rail guides reduce alignment and installation time
l Rail material: hard-anodized aluminum or stainless steel (316L)
l Turn-to-fit function for clearance adjustment optional
➤ Page 930
Accessories
l Manual clamp available
l End caps for select rails
➤ Page 937
Hybrid guides
l Combination rolling and sliding bearings
l Low driving forces - ideal for manual applications
l Bearing with single or double roll
l Suitable with DryLin® single and double rail profiles
➤ Page 941
DryLin® linear bearings enable precise positioning at high speeds, Low weight and quiet, precise movement, DryLin® bearings are used
and do not require external lubrication like traditional bearings. in a number of 3D printing applications.
The adjustment mechanisms of fitness equipment require no This casting machine’s closing mechanism is subjected to high
maintenance when manufactured with DryLin® profile guides. temperatures as well as dirt. To make the system as durable as
possible despite these harsh conditions, it is equipped with a DryLin®
W linear guide.
On this complex machine, the price advantage, coupled with Stage technology’s requirements for quiet, low-vibration adjustment
resistance to dirt and dust were the customer’s deciding factors for are enabled through the use of steel DryLin® W linear guide systems
selecting DryLin® W. partnered with self-lubricating iglide® sliding elements.
➤ www.igus.com/drylin-expert
With the DryLin® expert 2.0 online tool, easily configure the right
DryLin® system for your application, and calculate service life with
only a few clicks. Enter relevant parameters and environmental
factors, select the bearing size, carriage, position, and number.
Next, enter the distance between the rails and mounting, define
the coordinates for the drive location and center of gravity.
Define the weight, required drive force, and distance of the
bearing, and select the rail length, and select and order from the
displayed results.
➤ www.igus.com/drylin-expert
The igus® CAD configurator gives you the ability to design and
save your linear guide system, individual components directly as
a 3D model in all commonly used formats, or to have them sent
via email – No cost or registration required.
➤ www.igus.com/drylin-CAD
= Standard liner
square
•
Mono-slide carriage
Combinations
Single rail Double rail High profile rail
square round square round square round
Housing bearing,
round
Housing bearing,
square
Mono-slide carriage
Bearings/carriages
Housing material Options
Zinc Stainless Manual Clearance Ø 10 mm Floating
Aluminum Hybrid
Die-cast steel clamp adjustment slider bearing
Housing bearing,
round
Housing bearing,
square
Mono-slide carriage
Rails
Rail material Fastening options
Stainless Pre-drilled Clamping
Aluminum Holes Slot nuts
steel thread (3/8”) element
FixedFloating
± .008 in (0.2) mm
LL – Round
± .04 in (1) mm
FixedFloating
LLY – Angular
FixedFloating
LLZ – Angular
+/- 7°
Axial retention
Corrosion resistant
The "all-rounder" – The specialist – The extreme – The marathon runner – FDA compliant –
iglide® J iglide® J200 iglide® T500 (X)* iglide® E7 iglide® A180
Aluminum, Hardened stainless steel Steel
Optimal shaft material(s) all shaft materials
hard anodized Hard chromed plated steel stainless steel shaft
all shaft materials
-40°F to +194°F -40°F to +194°F -148°F to +482°F -40°F to +194°F -40°F to +194°F
Application temperature (-40°C to +90°C) (-40°C to +90°C) (-100°C to +250°C) (-40°C to +90°C) (-40°C to +90°C)
Aluminum, Steel hard Steel
Best coefficient of friction with Steel shaft
hard anodized chrome-plated stainless steel shaft
Stainless steel shaft
Aluminum, Aluminum, Hardened Steel
Maximum life time hard anodized hard anodized stainless steel stainless steel shaft
Stainless steel shaft
Permissible stat. surface pressure 35 MPa 23 MPa 150 MPa 18 MPa 28 MPa
Moisture absorption 1.3% weight 0.7% weight 0.5% weight < 0.1% weight 0.2% weight
Volume resistance > 1013 Ωcm > 108 Ωcm < 105 Ωcm > 109 Ωcm > 1012 Ωcm
Suitable liners
Square bearing
Standard •
Aluminum •
Round bearing,
Standard • • • • •
Stainless steel • • • • •
Aluminum • • • • •
Aluminum, tandem • • • • •
"Turn to fit" •
Hybrid –
roll and slide •
Guide carriage, fitted
Standard,
assembled,
square
•
Standard,
assembled,
round
• • • • •
Hybrid,
round •
"Turn-to-fit", round •
Complete carriages
One-piece
square •
•= Standard •= Optional *X is the European equivalent material for iglide® T500
A3
C3
A3
C3
K1
A3
K1
K1
G1
G1
G2
G1
G2
G2
C6 +/- 1mm C4 C5 +/- 1mm
C6 +/- 1mm C4 C5 +/- 1mm
L +/- 2mm
C4 C5 +/- 1mm
C6 +/- 1mm
L +/- 2mm
L +/- 2mm
B y x
B y x z
WJ200QM-01-... B K2 ! Coz- z y x ! Coz-
WJ200QM-01-... K2 ! Coz- z ! Coz-
WJ200QM-01-... K2 ! Coz- ! Coz-
Coy- Coy-
Coy-
da
Q1
H
da
Q1
H
h2
da
h2
Q1
H
K3
h2
K3
h
K3 A1 a h1
WSQ-...
h
A1 a h1
WSQ-...
h
A1 a Q2
h1
WSQ-... Q2
Q2
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the tribology of the bearing
system - therefore variations in color, and superficial crazing under the anodic layer may occur.
Hard anodized surfaces ➤ Page 888
WJ200QM-...
WSQ-06-3000 WJ200QM-01-10-LLY
Floating bearing in
Quantity, bearings
Housing bearing,
Rail length [mm]
iglide® bearing
Guide rails
y-direction
DryLin® W
Shafts-Ø
material
Square
square
Size
Options
LLY: Floating bearing in y-direction
LLZ: Floating bearing in z-direction
AL: Aluminum housing bearing
Order example:
WJ200QM-01-06 for a housing bearing, square
WJ200QM-01-06-LLZ for a housing bearing, square with floating z-direction
WJ200QM-01-06-AL for a housing bearing, square, made from aluminum
A3
K1 C3
A3
C1
K1
C3
A3
G1
G2
K1
G1
G2
G1
C6 +/- 1mm C4 C5 +/- 1mm
G2
L +/- 2mm
C4 C5 +/- 1mm
C6 +/- 1mm
L +/- 2mm
C6 +/- 1mm C4 C5 +/- 1mm
L +/- 2mm
B
Coy-
y *
! Coz-
x
B K2
WJ200UM-01-..
WJ200UM-01-..
K2
! Coz- z Coy-
! Coz-
B
d1
da
Q2
H
! Coz- Coy-
! Coz-
K2
H h2
WJ200UM-01-.. K3
d1
da
Q2
h h2
WS-..
K3 A1
! Coz-
a
h1
di
d1
da
Q2
H
WS-.. A1 a
h1
h2
di
K3 Q1
h1
di
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the tribology of the bearing system - therefore variations in color, and
superficial crazing under the anodic layer may occur.
Hard anodized surfaces ➤ Page 888
Order key
WJ200UM-01-10-LL
Housing bearing,
Floating bearing
iglide® J200
Number of
DryLin® W
bearings
round
C1
Liner
Size
B C3
A3
K2 ! Coz-
Options
LL: Floating bearing
AL: Aluminum housing bearing
H
K3
Order example:
WJ200UM-01-10 for a housing, round, J200 liner
WJ200UM-01-10-LL for a housing, round, floating bearing
WJ200UM-01-10-AL for a housing, round, made from aluminum
WS-... WS-..-ES-FG-... WS-... WS-...-ES-FG WSX-... iglide® J iglide® J200 iglide® T500 iglide® E7 iglide® A180
WJ200UMT-01-10-AL
C1
Housing bearing,
C3
A3
iglide® J200
Twin length
Aluminium
DryLin® W
Standard
round
Liner
Size
C1
C3
A3
B
K2
K3
B
K2
WS-... WS-..-ES-FG-... WS-... WS-...-ES-FG WSX-... iglide® J iglide® J200 iglide® T500 iglide® E7 iglide® A180
Order key
Type Size
WJ200UME-01-10
Housing bearing,
iglide® J200
Adjustable
DryLin® W
Standard
round
Liner
Size
C1
B C3
A3
K2 ! Coz-
H
K3
C1
C3
A3
K1
DryLin®
C1
C3
STAINLESS
A3
K1
G1
STEEL
G1
da
G2
C6
da
C4 C5
G2
C6 C4 C5
± 1mm L ± 2mm
± 1mm L ± 2mm
Q1
H
K3
h2
h
Q1
H
K3
h2
A1 a
h1
h
A1 a
h1
57)
Height dimension minus the bearing clearance tolerance 58)
With plain holes
WJ200UM(T)-... WJ200UME-... WJUM-..-ES-FG WJRM-... iglide® J iglide® T500 iglide® E7 iglide® A180
A3
K1
C3
K1
A2
da
A2
da
C6
± 1 mm C6C4 C5
C4 C5
L ± 2 mm ± 1 mm
L
y y
B x x
B
Size 10-20 K2 z K2 z
b b
Material for housing and shaft support 1.4408 (AISI 316) ! Coz- ! Coz-
Shaft material 1.4571 (AISI 316Ti)
h
Size 25
H
K3 K3
h2
h2
Material for shaft, shaft support, housing 1.4571 (AISI 316Ti)
a a
57)
Height dimension minus the bearing clearance tolerance
DryLin®
STAINLESS
STEEL
A3
C6 K1 ± 1 mm
A3
± 1 mm ± 1 mm
± 1 mm
C4
da
C1
da
G1
C3 C5
G2
C6 K1
A3
G2
± 1 mm
± 1 mm
b
da
G1
G2
dr
dr
b
L ± 2 mm L ± 2 mm
dr
L ± 2 mm
B B
K2 K2
B
WJ200QM-01-06
WJ200QM-01-06 K2
h2
h2
Q2
da
WJ200QM-01-06
Q2
da
K3
h
y
h2
K3
x
Q2
da
H
h
K3
h1
h1
WSQ-06-30 WSQ-06-30
A1 aA1 Q1
z
h1
WSQ-06-30 A1 a a Q1 Q1
C4
± 1 mm C4C1 ± 1 mm
A3
± 1 mmC6 K1 C1C3 ± 1C5
mm
A3
C6 K1 C3 C5
NOTE: The hard anodized surface of DryLin rails
da
G1
and shafts is integral to the tribology of the bearing
da
G1
system - therefore variations in color, and superficial
G2
crazing under the anodic layer may occur.
G2
b
b
Hard anodized surfaces ➤ Page 888 dr
L ± 2 mm
dr
L ± 2 mm
B
K2
B
WJ200QM-... K2 h2
Q2
da
H
WJ200QM-... K3
h2
Q2
da
Q1
H
WSQ-... a1
K3
A1 a
Q1
Technical data and dimensions [mm] WSQ-...
A1
a1
a
Profile rail
Shafts-Ø
6 5 4
H
h
D
C
b A1
K1
di
da
H
X
h2
h
s
nh
B
G1
n
C nb
C3
a
C1
s
B
nh n nb T X Y ly lz
[mm4] [mm4]
7 - - M5 12 10 30,391 11,674
57)
Height dimension minus the bearing clearance tolerance
Order example:
WSX-06-30: High profile rail, square
WSQ-06-30: Standard double rail, square A
6 5 4
Order key
Type Size
WW-06-30-06
Carriage length
Guide carriage
Shafts-Ø [mm]
K2
Profile width
WW-06-30-...
K2
WW-06-30-...
A2
A
A2
A
C2
C
C2
C
WJ200QM-01-06
H2
WJ200QM-01-06
H2
WSQ-06-30
WSQ-06-30
57)
Height dimension minus the bearing clearance tolerance
Order example:
WW-06-30-06: fitted guide carriage
WWC-06-30-06: Mono-Slide guide carriage
Order key
Type Size
K2
WWC-10-40-10
Length of carriage
Shafts-Ø [mm]
guide carriage
Profile width
Mono-Slide
A2
A
K2
C2
C
A2
A
H2
C2
C
profile C4 C1
A3
A3
C4
G1
C1
G2
G1
G2
C6 +/- 1mm C3 C5 +/- 1mm
K1
A3
b
K1
G1
G2
K1
b
L +/- 2mm
L +/- 2mm
L +/- 2mm
B y x
B z
! Coz- y x
K2
! Coz-
di z y x
WJ200UM-01-.. K2 di
z
! Coz-
WJ200UM-01-..
da
Q2
H
K3
! Coz-
h1
h2
B y x
da
Q2
H
K3
h1
h
z
h2
! Coz-
WS-.. K2 a1 di
h
WS-.. A1
di This orientation not
WJ200UM-01-.. a1 a
A1 a
di possible for:
! Coz-
Q1
WS-10-40
da
Q2
H
K3 Q1
h1
h2
WS-10-80
h
WS-.. a1 WS-10-120
di
A1 a
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the tribology of the bearing Q1
system - therefore variations in color, and superficial crazing under the anodic layer may occur.
Hard anodized surfaces ➤ Page 888
Technical data and dimensions [mm]
Part No. Weight H57) da di L a A1 b h h1 h2 G1 G2 a162) Q1 Q2
[kg/m] ±0.25 max.
Order key
Type Length
WSX-10-80
WSX-10-40-4000
4 3 2 1
6 5 4
Profile rail
Shafts-Ø
WSX-16-60
H
WSX-10-40
h
D
WSX-10-40 and WSX-10-80 use part # 75.40
WSX-16-60 use part #C 75.50 b A1
Not included in delivery d i
K1
da
H
X
h2
h
nh
s
n
G1
C nb
C3 a
C1
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the tribology of the bearing
system - therefore variations in color, and superficial crazing under the
A
anodic layer may occur.
Hard anodized surfaces ➤ Page 888
4 3 2 1
Technical data and dimensions [mm]
Part No. Weight H57) da di L a A1 b h h2 s K1 C1 C3 G1
s
B
[kg/m] ±0.25 –0.1 max.
nh n nb T X Y ly lz
[mm4] [mm4]
57)
Height dimension minus the bearing clearance tolerance
6 5 4
A A2
A
A2
C2
y x C2 C
In the following sizes, also available z C
with adjustable clearance:
10, 16 and 20; order example: WJ200UM-01-...
WWE-10-40-15
H2
WJ200UM-01-...
H2
WS-...
WS-...
Technical data and dimensions [mm]
57)
Height dimension minus the bearing clearance tolerance
WS-... WS-...-ES-FG WSX-... iglide® J iglide® J200 iglide® T500 iglide® E7 iglide® A180
WSQ-06-30-CAM-500
K4
K1 (8x)
WS-10-40-CAM-500
L ± 2 mm
0.5 x L
C5 C4 C6
± 1 mm ± 1 mm
K4 S K1 (4x)
20 WS-10-40-CAM-1000
K4 K1 (10x)
63)
* UNC = Unified National Coarse, Imperial. Screw thread standard
Application example:
Camera slider with standard rail and carriage
➤ www.igus.com/camera
Technical options:
Adjustable bearing housing
Manual clamp (WW...-HKA ➤ Page 937
C/2
K3 K2
K1
A2
A
b
C5 C6
L/2 ± 1
L ± 2 mm H C2
C
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the tribology of the bearing
system - therefore variations in color, and superficial crazing under the anodic layer may occur.
Hard anodized surfaces ➤ Page 888
DryLin® W complete carriage with ø10 mm through hole for 3/8" thread - Dimensions [mm]
64)
Optional with integrated manual clamp (add suffix "-HKA")
65)
Optional with adjustable "Turn-To-Fit" bearing to reduce bearing clearance (Order example: WWE-…)
Dk
Manual clamp for simple positioning
Vz
Kz
Mk
Manual clamping, for Kx
simple positioning
Vx
WHKA- ...
Dk
Technical data and dimensions [mm]
Vz
WHKA-1066) M6 50 33 8 28 20 30 N 0.8 Nm
Kz
WHKA-1666) M8 72 41 10 31 28 60 N 1.5 Nm
WHKA-20 66)
M8 90 62 10 31 28 70 N 1.5 Nm
Kx
WHKA-25 66)
M8 96 65 12 31 28 70 N 1.5 Nm
Vx
66)
The manual clamp is also available assembled as a complete carriage (suffix "-HKA", order example WW-10-40-10-HKA)
➤ Complete carriage WW, Page 934
67)
Condition: dry rail surface
Please Note: The creep behavior of the clamped plastic results in reduced clamping force over time (up to 70%). Therefore safety-related parts
should use an alternative method.
Kz
Vz
Kx
Manual clamping,
Vx
for simple positioning
WHKD- ...
Mk
Dk
WHKD-1015 69)
M6 150 95 40 10 40 70 N 2.5 Nm
Vz
WHKD-1615 69)
M8 150 81 40 12 40 90 N 3.5 Nm
WHKD-162069) M8 200 131 10 12 40 90 N 3.5 Nm
WHKD-2015 69)
M8 150 63 40 12 40
Kx 90 N 3.5 Nm
WHKD-2020 69)
M8 200 113 40 12 40 Vx 90 N 3.5 Nm
69)
The hand clamp WHKD is available assembled in the following complete carriages: WW-10-40-10-HKD, WW-20-80-15-HKD.
Dimensions ➤ Complete carriage WW, Page 934
67)
Condition: dry rail surface
Please Note: The creep behavior of the clamped plastic results in reduced clamping force over time (up to 70%). Therefore safety-related
parts should use an alternative method.
70)
Depending on assembly direction, can be used as a y or z floating bearing
*X is the European equivalent material for iglide® T500
1
Installation size Max. tightening Thread
torque [Nm]
W-06 1.5 M4
W-10 6.0 M6
F = 50 N
W-16 15.0 M8
W-20 15.0 M8
W-25 30.0 M10
1
Installation size Max. tightening Thread
torque [Nm]
W-06 1.5 M4
W-10 6.0 M6
F = 50 N W-16 15.0 M8
W-20 15.0 M8
W-25 30.0 M10
2
Please refer to the drawing for the correct
screw assembly sequence.
DryLin® WJRM
Single bearing with single or double plastic rollers
iglide® J sliding bearing with plastic support roller
Can be combined with DryLin® W single and double rails
➤ Page 946
DryLin® WWR
Complete carriage assembly for lateral adjustments
DryLin® W double rail profiles
Also available as a short, compact carriage for multi-carriage
solution
➤ Page 948
DryLin® WWH
Complete carriage with 4 integrated hybrid bearings
For horizontal installation
Available in 2 sizes, also suitable as a camera slider
➤ Page 949
The smooth, quiet operation and enormous cost advantages are utilized on the door guards of this machine tool using DryLin® Hybrid bearings
Control panel adjustment unit This camera slider using DryLin® WJRM hybrid bearings offers
extremely smooth performance, as well as guiding vertical movement
The new DryLin® W hybrid carriage on a sliding door application DryLin® W hybrid bearings and W profile guide systems used in
camera dollies and sliders.
A3
A3
create greater friction forces.
C3
A3
G1
G1
G1
C1
C1 C3
A3
C3
A3
G1
G1
B
Forces absorbed by hybrid bearing Forces absorbed by hybrid double roller bearing
B K2
K2
Z
Z
H
y
H
y
A1
A1
Installation position 01 Installation position 02
350 350
300 300
250 250
Lebensdauer (km)
Lebensdauer (km)
200 200
Service life (km)
(km)
150 150
Service life
100 100
50 50
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800
Order key
C1 C1Type
C3 C3
WJRM-01-10
A3
A3
G1
G1
With one roller
Hybrid bearing
Size 10
WJRM-01-10 WJRM-01-10
WJRM-01-16 WJRM-01-16
WJRM-01-16 WJRM-01-16
WJRM-01-20 WJRM-01-20
WJRM-01-20 WJRM-01-20
C1 H H
B2
B2
C3 K3 K3
A3
A1
A1
Q2
Q2
B
B
K2
K2
G1
Q1 Q1
K3
Part No. Static load Dynamic load capacity Cz+
F·v
A1
Order key
Type
WJRM-21-20
Hybrid bearing
A3
Size
G1
C1
C3 B
A3
K2
Z
G1
H
y
A1
B
K2
Technical data and dimensions [mm]
Part No. Static loadZ Dynamic load capacity Cz+
F·v
H
capacity
y Co at total running distance (km)
WJRM-21-10 and WJRM-21-16: 70° angle between the rollers / WJRM-21-20: 80° angle between the rollers
Order key
H3 H3
WWR-21-80 - 01
A
A3 carriageA2
A
A2
Installation size
DryLin® W
Compact
Hybrid
C2C2 H2 H2
A3
C C Options
01: Carriage, short design
15: Complete carriage, long design
WWR-21-80-15
H3
wx wx
K2
A
A2
Fs Fs
C2 H2 Fs Fs
A3
sx sx sy sy
sx Width Length
sy ±0.17
WWR-21-80-01 143 90 100 70 M8 54 15 6 -49 +49 -34 +34
WWR-21-80-15 143 150 100 120 M8 54 15 6 -wx/2 +wx/2 -34 +34
Order example:
WWH-10-40-10: Assembled hybrid carriage with 4 single roller hybrid bearings
WWR-21-80-01: Assembled single hybrid carriage as a "door opener" with 2 single roller hybrid bearings and 2
double roller hybrid bearings
Order key
Type Dimensions
WWH-10-40-10
C2
C
K2
C2 H2
C
H2
A2
A
Dimensions [mm]
Part No. Weight A C A2 C2 K2 H2 Static load capacity
Coy Coz Mox Moy Moz
[kg] ±0.17 [N] [N] [Nm] [Nm] [Nm]
WWH-10-40-10 0.35 58 100 40 80 M5 34 1,000 1,000 20 16 32
WWH-16-60-15 0.96 84 150 60 120 M6 46 1,600 1,600 45 38 77
WWH-20-80-25 2.05 134 250 116 232 M8 57 3,360 3,360 138 640 640
• Low-profile
• Interchangeable sliding elements
• Anodized aluminum rail
• High speed and acceleration possible
• Self-lubricating
• Low weight
951
DryLin® N - Low-profile guide systems - Advantages
Lightweight, maintenance free, corrosion resistant and low wear
Linear guide
l 4 Sizes 17, 27, 40 and 80 mm
l Corrosion resistant and light weight
l Standard hole pattern or no hole rail
l Clear anodized (silver) or “Black edition” (black
anti-reflection surface)
➤ From page 958
Carriage – size 17
l Solid plastic made from high-performance plastic
iglide® J, brass thread
l Standard, preload (PL), floating (LL)
Size 17
l Easy to fit due to available double carriage in
30 mm /40 mm length
l Designed for the smallest installation spaces
➤ Page 959
Carriage – size 27
Size 27 l Many carriage and material options with lengths of up to 80
mm
l Zinc casting with clip-on or overmolded plastic liner
l Standard, preload (PL), floating (LL)
l High-temperature carriages and manual clamp available
➤ Page 961
Carriage – size 40
Size 40
l Zinc die-casting with thread/through hole
l Standard, preload (PL), floating (LL)
l Multiple carriage options
➤ Page 963
Carriage – size 80
l Carriages with wide load-bearing surface
l Self-lubricating due to high-performance plastics J/J200
l Zinc casting with clip-on or overmolded plastic liner
l Carriages made from zinc casting or aluminum with threaded
holes (reduced installation height as no pins used)
Size 80 ➤ Page 965
Accessories
l End caps
l Manual clamp for size 27
l Telescopic rails (with/without locking function)
➤ Page 968
The low-profile size of DryLin® N makes it possible to achieve maximum DryLin® N low-profile guides and DryLin® SD lead screw drives perform
work area in this delta-style 3D printer. the height adjustments, and the black anodized DryLin® N profile
blends seamlessly into this 3D printer’s design.
In the redesign on this ATM machine, the durability and lack of main- The quiet, self-lubricating, and low-profile design of DryLin® N enabled
tenance, plus easy-to-install design of DryLin® N made it an ideal it to fulfill the safety requirements of this application. Multiple sections
bearing solution. of rails are joined to achieve the desired length.
The removal unit is moved along the X-Y axis using space and cost- This sampling device used DryLin® linear bearings to remove the
saving DryLin® N. sampled materials smoothly and precisely.
The igus® CAD configurator gives you the ability to design and
save your linear guide system, individual components directly as
a 3D model in all commonly used formats, or to have these sent
via email – No costs or registration required.
➤ www.igus.com/DryLin-CAD
System selection
System N17 N27 N40 N80
Rail width 17 mm 27 mm 40 mm 80 mm
Installation height 6 mm 9.5 mm 9.5 mm 12 mm
General properties
Rail weight 150 g/m 290 g/m 450 g/m 1,140 g/m
Carriage weight 1.7 g 9–12.5 g 30 g 100 g
Max. rail length 2,000 mm 3,000 mm 3,000 mm 4,000 mm
Load capacities, static
Fy 50 N 500 N 700 N 1,000 N
Fz 50 N 500 N 700 N 1,000 N
Mx 0.31 Nm 5 Nm 10 Nm 32.4 Nm
My, Mz 0.18 Nm 2.5 Nm 6 Nm 15 Nm
Carriage options
Floating bearing in y-direction
Floating bearing in z-direction
Floating bearing in yz-direction
Preload (1 N) –
Molded version –
Carriage with plain hole – –
Carriage with threaded hole
1.000
100
Load F [N]
10
0.1 1.0 10
Speed v [m/s]
Size 17 Size 27 Size 40 Size 80
Diagram 01: F v diagram, maximum permissible dynamic load
C
C2
C
C2
C5 C6
± 1 mm C4 ± 1 mm
C5 L ± 2 mm
C6
± 1 mm C4 ± 1 mm
L ± 2 mm
A
Standard, Anodized Black Dp
Sp
anodized without anodized, K3
with holes holes with holes
A
Dp
y x
Sp
K3
h
z
h1
K1
NW-02-17 NW-02-17-P
a
H
h
h1
K1
a
NW-22-17-30 NW-22-17-40
NW-02-17 • • •
NW-02-17-P • • • •
NW-22-17-30 • • •
NW-22-17-40 • • •
Order key
Installation Type
Type Options
size 02 = Carriage with threaded mounting boss
22 = Double carriage with threaded mounting boss
NW - 22 - 17 - 30 - LLY Options
P= Preload
Floating bearing in
Floating bearing
Guide carriages
Carriage length
Carriage type LLY = Floating y-direction
LLZ = Floating z-direction
y-direction
LLYZ = Floating yz-direction
Rail width
DryLin® N
NS-01-17- 72) 2,000 17 60 20 49.5 5.5 0.9 Ø3.5 1,700 120 150
NS-01-17-AR- 72)
(black anodized) 2,000 17 60 20 49.5 5.5 0.9 Ø3.5 1,700 120 150
72)
Please add the required length in mm , symmetrical standard hole pattern C5 = C6
73)
For cap screw with low head (i.e. DIN 7984, DIN 6912, DIN 84, EN ISO 1707)
Order example:
NS-01-17-1500 = Guide rail, size 17, length 1 @ 500 mm
NW-02-17-P-LLY = Guide carriage with threaded pin, size 17, preload, floating bearing in y-direction
C
C1
C2
NW-01-27 NW-02-27
C5 C6
± 1 mm C4 ± 1 mm
NW-01-27-P NW-02-27-P
L ± 2 mm
C2
Design: one-piece Design: clipped-on
Standard, Anodized Black overmolded liner liner
anodized without anodized, Dp
with holes holes with holes
A K3
NW-01-27-HT NW-02-27-HT
K
H2
A2
A3
Sp
y x
z
H
h
h1
K1
NW-21-27-60-P NW-22-27-60-P NW-11-27 NW-12-27 a
Dp
A
Dp K3
A K3
K
H2
Sp
H2
Sp
H
h
H
h
h1
h1
K1
K1 a K4
NW-11-27-80 NW-12-27-80 NW-12-27-80-HKA a
Order key
Carriage type
Type Size Options
See selection aids
Options
NW - 01 - 27 - HT - LLY P= Preload
HT = High temperature 266°F (130°C)
Floating bearing in
Floating bearing
High temperature
Guide carriages
y-direction
Rail width LLYZ = Floating yz-direction
DryLin® N
NS-01-27-AR- 72)
(black anodized) 3,000 27 60 20 49.5 9 1.1 Ø4.5 6,524 588 290
72)
Please add the required length in mm , symmetrical standard hole pattern C5 = C6
73)
For cap screw with low head (i.e. DIN 7984, DIN 6912, DIN 84, EN ISO 1707)
73)
For cap screw with low head (i.e. DIN 7984, DIN 6912, DIN 84, EN ISO 1707)
74)
Metal thread
Order example:
NS-01-27-1500 = Guide rail, size 27, length 1 @ 500 mm
NW-02-27-P-LLY = Guide carriage with threaded mounting boss, size 27, preload, floating bearing in y-direction
C C5 C5 C6 C6
± 1 mm ± C4
1 mm C4 ± 1 mm ± 1 mm
C1
L ± 2 mm L ± 2 mm
C2
Sp
anodized without holes with holes K3 Dp
K K
with holes
H2
K
H2
H
y
h
x
h
z
h1
K1
h1
C5 a C6 K1
NW-01-40 NW-02-40 ± 1 mm C4 ± 1 mm
a
L ± 2 mm
A Dp
Sp
K3
K
H2
NW-01-40-P NW-02-40-P
H
h
h1
K1
a
NW-11-40 NW-12-40
Order key
Carriage type
Type Size Options
See selection aid
Options
NW - 01 - 40 - P - LLY P= Preload
Floating bearing
Floating bearing in
LLY = Floating y-direction
Guide carriages
y-direction
Rail width
DryLin® N
Preload
NS-01-40- 72) 3,000 40 60 20 49.5 8.7 1.3 Ø4.5 26,400 970 450
NS-01-40-AR- 72)
(black anodized) 3,000 40 60 20 49.5 8.7 1.3 Ø4.5 26,400 970 450
72)
Please add the required length in mm , symmetrical standard hole pattern C5=C6
73)
For cap screw with low head (i.e. DIN 7984, DIN 6912, DIN 84, EN ISO 1707)
Order example:
NS-01-40-1500 = Guide rail, size 40, length 1,500 mm
NW-02-40-P-LLY = Guide carriage with threaded pin, size 40, preload, floating bearing in y-direction
A2
A3
A2
A3
C5 C6
± 1 mm C5 C4 ±C6
1 mm
± 1 mm C4 ± 1 mm
L ± 2 mm
L ± 2 mm
AA
K4K4
y x
z
hh
H
NW-12-80 K1
h1
h1 K1 a
Overmolded
a
NW-02-80 • • •
NW-12-80 • • •
Order key
Carriage type
Type Size Options
See selection aid
Options
NW - 02 - 80 - LLY Floating bearing
LLY = Floating y-direction
Floating bearing in
LLZ = Floating z-direction
Guide carriages
y-direction
Rail width
DryLin® N
NS-01-80- 72) 4,000 80 150 40 25 99.5 11 1.5 Ø4.5 27,120 2,900 1,140
NS-01-80-AR- 72) 4,000 80 150 40 25 99.5 11 1.5 Ø4.5 27,120 2,900 1,140
72)
Please add the required length in mm , symmetrical standard hole pattern C5=C6
73)
For cap screw with low head (i.e. DIN 7984, DIN 6912, DIN 84, EN ISO 1707)
74)
Metal thread
Order example:
NS-01-80-1500 = Guide rail, size 80, length 1,500 mm
NW-02-80-LLY = Guide carriage, clip-on, size 80, floating bearing in y-direction, suitable for size 80 guide rails
Order key
NT-35-“L” – Total extension
Type Size
C5 = 20 – 49.5 mm N T - 35 - 300
L L
Telescopic system
60 C6 C6 = 20–49.5 mm 60 C5
Length [mm]
Rails width
DryLin® N
NT-35-”L”-”L+20” – Over-extension
Over extension order key
Type Size Option
L 20 L
N T - 35 - 300 - 320
Telescopic system
Over extension
Length [mm]
Rails width
DryLin® N
L [mm]
B L Partial extension order key
Type Size Option
N T - 35 - 300 - 200
Option:
Telescopic system
Partial extension
Partial extension
b (e.g.: telescoped
Fmax = 75 N · (200 mm/L) length 300 mm,
Length [mm]
Rails width
extended length
DryLin® N
H
500 mm)
[mm]
M4 Recommendation:
Fmax calculated using this formula allows an easy manual
use. The unit can take higher forces than this, but the
required driving force will be correspondingly higher.
Dimensions [mm]
Part No. b H L min. L max.
NT-35-… mm 35 19 100 600
Order key
C5 = 20–49,5 mm
L L
Type
C5 = 20–49,5 mm Size Option
60 L C6 = 20–49,5 mm L 60 C5
60 N T - LM
C6 - 35 - 300
60 = 20–49,5 mm C5
Telescopic system
Length [mm]
mechanism
L 20 L
Rail width
DryLin® N
L 20 L
Locking
C5 = 20–49,5 mm
C5 = 20–49,5 mm
L L L L
L L B B LL
60 C6 = 20–49,5 mm 60 C5
60 C6 = 20–49,5 mm 60 C5
H
H
M4
L 20 L M4
L 20 L Fmax = 75 N · (200 mm/L)
b
L
BL L
B L
H
H
M4
M4
Fmax = 75 N · (200 mm/L)
b
Fmax
DryLin® NT LM in adjustment of = 75 Nguard
Perspex · (200 mm/L) DryLin® NT LM in guard door adjustment in a machine tool
b
DryLin® detent in end and center position at full extension – Dimensions [mm]
Part No. b H Lmin Lmax
NT-LM-35-...mm 35 19 140 600
Individual position detent on request; The length divided by the locking distance must be an even number.
e.g. Lengths 250 mm, latching all 62.5 mm = 250 / 62.5 = 4
Order example:
NT-LM-35-300 = DryLin® N telescopic rail with locking mechanism, 35 mm width, retracted length 300 mm
Order key
NW - 02 - 27 - 80 - HKA
Guide carriages
Carriage length
Manual clamp
Carriage type
Rail width
DryLin® N
Dr
Dp K3
(h2)
Sp
Dr
C A
C1 a
Dp K3
C3 C2
(h2)
Sp
C A
C1 a
C3 C2
Dimensions [mm]
Order example:
NW-12-27-80-HKA = Manual clamp for NW-12-27-80 carriage
Order key
Type Size
N S K B - 40
DryLin® N –
Rail width
End caps
Plugged
Size 80 shown for example only
Dimensions [mm]
Order example:
NSK-40 = end caps for rail size 40, bolted
Easily assembled and disassembled by hand using a screw driver. End caps for rail size 40, screwed
Part No.: NSKB Part No.: NSK-40
• Corrosion-free
• Wear-resistant
• Low friction
• Extremely quiet operation
• Self-lubricating
971
DryLin® T - Rail guide systems - Advantages
Resistant to dirt, low vibration, low noise, long service life
s as most
di
on s
Self-lubricating rail guide
e
earing guid
n
Same dime
ba
ll b systems - DryLin T ®
4 sizes
7 carriage types
Rail lengths up to 4,000 mm
Adjustable bearing clearance
Automatic
l With a mechanism that automatically adjusts the bearing
clearance after removal of the preload key and adjusts during
operation
l Self-lubricating and maintenance-free
l Corrosion-resistant
➤ Page 979
Standard
l Supplied preset and can be put into operation at once
l Manual clearance adjustment or fine tuning
l Self-lubricating and maintenance-free
l Corrosion-resistant
➤ Page 980
Heavy duty
l Used for the most extreme conditions (dirt, adhesive
residues, chips, mud, etc.)
l Bolted aluminum cover plates mechanically secure bearing
liners
➤ Page 982
Compact
l Narrow linear guide carriage for small installation space
l Plastic sliding elements are fixed in the cover plate and are
therefore permanent
l Clear anodized and weight- reduced guide rail optionally
available
➤ Page 983
Miniature
l Small, compact, self-lubricating
l Adjustable clearance option
➤ Page 984
l Precision
l High corrosion resistance
➤ Page 984
Clamps
l Compact and strong clamps for all sizes – holding forces up
to 500 N
➤ Page 986
Long service life and food-grade quality, along with the ability to stand The adjustment of the pressure roller and adjustment of the of the
up to humidity and harsh cleaning products, are all requirements for grinding wheel balance are done here with DryLin® T in place of
this application. recirculating ball bearing guides.
The DryLin® T linear guide systems are used in these mail room DryLin® T linear guide systems find balance between service life and
machines to guide the suction cup opening mechanisms. costs despite the welding spatter and dust in this harsh application.
The height of this work table is adjusted quietly and precisely with This measurement system must make quick, seamless tool changes
the use of the DryLin® T rail guide systems in dusty environments, with major time savings through the use of
DryLin® T.
➤ www.igus.com/drylin-expert
➤ www.igus.com/drylin-CAD
Rail
Fixed
bearing Fixed
bearing
Automatic compensation of
Carriage Floating
parallelism errors bearing VF-Y
Floating
Fixed bearing bearing HF
Floating
bearing HF
Guide rails
Material Extruded aluminum
Material 6063-T6 or 6060-T66 (Al Mg Si 0.5)
Coating Hard-anodized aluminum, 50 µm
Hardness 500 HV
Guide carriages
Base structure Extruded aluminum
Material 6060-T66 (Al Mg Si 0.5) / 6063-T6
Coating Anodized aluminum
Sliding elements Maintenance free plain bearing iglide® J
Bolts, springs Stainless steel
End cap Plastic (TW-01/TWA-01), steel (TW-02)
Max. surface speed 15 m/s
Temperature range –40°F to +194°F (-40°C to +90°C)
Table 02: DryLin® – permissible static load capacity Diagram 01: Designation of load directions
10.000
1.000
100
Load F (N)
10
0.1 1.0 10
Speed v (m/s)
Order key
Type Options
TS - 01 - 15 - 1000 - CA
Clear anodized
TS-01-... TS-11-...
Guide rails
Type 01
NOTE: The hard anodized surface of DryLin rails and shafts is integral to the
tribology of the bearings system - therefore variations in color, and superficial
crazing under the anodic layer, may be occur.
Options
Rails without mounting holes available TS-01 = Standard rail
Hard anodized surfaces ➤ Page 888 TS-11 = Lower weight hollow
h1
b
K1
h C5 C4 C6
± 1 mm
L ± 2 mm
Dimensions [mm]
Part No. Weight L a C4 C5 C5 C6 C6 h h1 K1 for screw b ly lz Wby Wbz
[kg/m] max. –0.2 min. max. min. max. DIN 912 [mm4] [mm4] [mm3] [mm3]
TS-01-15 0.6 4,000 15 60 20 49.5 20 49.5 15.5 10.0 M4 22 6,440 4,290 585 488
TS-01-20 1.0 4,000 20 60 20 49.5 20 49.5 19.0 12.3 M5 31 22,570 11,520 1,456 1,067
TS-11-20 76)
0.5 4,000 20 120 20 79.5 20 79.5 19.0 12.3 M5 31 12,140 6,360 780 620
TS-01-25 1.3 4,000 23 60 20 49.5 20 49.5 21.5 13.8 M6 34 34,700 19,300 2,041 1,608
TS-01-30 1.9 4,000 28 80 20 59.5 20 59.5 26.0 15.8 M8 40 70,040 40,780 3,502 2,832
76)
TS-11-20: Clear anodized and weight- reduced guide rail
Standard hole pattern symmetric C5 = C6
For rails without mounting holes, please use part number suffix “S”: TS-01-XXS
In North America these may be stocked in 12 ft lengths.
Order key
Type Options
TWA - 01 - 15 - LLY
Floating bearing
Guide carriages
Installation size
Automatic
Standard
C
C3 C1 C3
K2
H5
K3
C2
A2
Y
X
H1
H
A1
Z
Dimensions [mm]
Part No. Weight H A C A1 A2 C1 C2 C3 H1 H5 K2- Torque K3 for screw
[kg] ±0.35 ±0.35 ±0.35 Thread max. [Nm] DIN 912
TWA-01-15 0.11 24 47 68 16.0 38 50 30 9 4.0 16.0 M5 1.5 M4
TWA-01-20 0.19 30 63 81 21.5 53 61 40 10 5.0 19.8 M6 2.5 M5
TWA-01-25 0.29 36 70 90 23.5 57 68 45 11 5.0 24.8 M8 6.0 M6
TWA-01-30 0.50 42 90 103 31.0 72 79 52 12 6.5 27.0 M10 15.0 M8
Order example:
TWA-02-20-LLY: guide carriage with automatic clearance adjustment, size 20 and floating bearing in y-direction
TS-01-...
Order key
Type Options
TW - 01 - 15 - LLY
Manual clearance
Floating bearing
Guide carriages
adjustment
C
C3 C1 C3
Height
K2
H5
K3
Options
C2 LLY = Floating bearing in y-direction
LLZ = Floating bearing in z-direction
A2
Y
X
H1
H
A1
Z
Dimensions [mm]
Part No. Weight H A C A1 A2 C1 C2 C3 H1 H5 K2- Torque
K3 for screw
±0.35 ±0.35 ±0.35 thread max.
[kg] [Nm] DIN 912
TW-01-15 0.11 24 47 74 16.0 38 50 30 9 4.0 16.0 M5 1.5 M4
TW-01-20 0.19 30 63 87 21.5 53 61 40 10 5.0 19.8 M6 2.5 M5
TW-01-25 0.29 36 70 96 23.5 57 68 45 11 5.0 24.8 M8 6.0 M6
TW-01-30 0.50 42 90 109 31.0 72 79 52 12 6.5 27.0 M10 15.0 M8
Order example:
TW-01-15 LLY: standard guide carriage with manually adjustable clearance,
size 15 and floating bearing in y-direction
TS-01-...
Order key
Type Options
TW - 01 - 15 - HKA
Manual clearance
Guide carriages
Installation size
Manual clamp
adjustment
C
C3 C1 C3
K2
H5
K3
A2
C2
Kz A
Y
Ky
X
H1
H
Dk
A1
Z
Dimensions [mm]
Part No. Size Kz Ky Dk Clamp thread
Order example:
TW-01-15-HKA: guide carriage with manually adjustable clearance, size 15 with manual clamp
The manual clamp has been developed for simple tasks. The creep behavior of the clamped plastic causes a reduction in clamping
force over time (up to 70%). Therefore safety-related parts should not be clamped. Please contact our applications consultant if
you require other options for the clamping.
TS-01-...
Order key
Type
TW - 02 - 20
Guide carriages
Installation size
Heavy Duty
C
H5
A
Y
X
H
Z
H1
Dimensions [mm]
Order example:
TW-02-20: heavy-duty guide carriage, size 20
TS-01-...
Order key
Type
TW - 03 - 25
Guide carriages
Installation size
L
C
C3 C1 C3
Compact
C5 K2 C4 C6
h
K1
H5
C1
K3
C2
h1
A2
b
C2
A2
Kz A
Y
Ky
A X
H1
H
Dk
K2 Z
a A1
H5
H
H1
A1
Dimensions [mm]
Order example:
TW-03-25: compact guide carriage, size 25
TS-01-20 TS-11-20
Installation size
Guide rails
Miniature
bh1
K1
b
K1
h
h1
h C5 C4 C6
a ± 1 mm
L ± 2 mm
Dimensions [mm]
± 1 mm
C5
TS-04-09 0.11 2,000 9 20 5 14.5 5 14.5 6.3 4.6 M2 9.6 252 169 52 49
TS-04-12 0.20 2,000 12 25 5 17.0 5 17.0 8.6 5.9 M3 13 856 574 132 120
TS-04-15 0.33 3,000 15 40 10 29.5 10 29.5 10.8 7.0 M3 17 2,420 1,410 285 239
C
C1
C2
C2
A
K2 y A2
x
A
z
H5
K2
A2
H1
H
H5
A1
H1
H
a K3
A1 a K3
Dimensions [mm]
C6
Order key
Type
TW E - 04 - 12
Adjustable clearance
Guide carriages
Installation size
L
C
L
C5 C1C C4 C6
C5 C1 C4 C6
Miniature
K1
K1
h
h1 h1
h
C2
C2
A
A K2
K2
E-coated for corrosion
H5
H1
H
b b
H5
resistance
A2
H1
H
A2
A1 a K3
A1 a K3
Dimensions [mm]
Part No. Weight H A C A1 A2 C1 C2 H1 H5 K2 K3 for screw
[g] ±0.2 –0.2 ±0.3 ±0.35 ±0.35 thread DIN 912
TWE-04-12 36 12 27 38 7.5 20 36 15 2.2 9.5 M3 M2
TWE-04-15 61 16 32 45 8.5 25 31 20 2.8 11 M3 M2
Tool: 3 mm flat-head screwdriver Right side: Insert screwdriver, and Left side: Insert screwdriver, and
depress internal nut, and turn to set depress internal nut, and turn to set
height clearance lateral clearance
TS-04-...
A lg
Order key
H2
H A lg
b
H1 Type
H2 a
H
TWBM - 11 - 25
b
H1
a
C2
K2
Compact design
Installation size
Manual clamp
C2
A2 C
K2
c
A2 C K
c
K
Pneumatic clamping
on request Options
11 = thin, compact design with
plastic clamping elements
01 = solid design with brass clamping
components, for size 25
Dimensions [mm]
H
H1
C2
K2
A2
A
H2
H
H1
bg
C2
lg
A2
A
Dimensions [mm]
bg
DryLin® T replacement liners (set) DryLin® T end caps for series 01 guide rail
Material iglide® J ➤ Page 115 holes:
Guide carriages Part No. Sliding part set Rail Part No. End cap
TW-01-15 TEK-01-15 TS-01-15 TSZ-011501
TW-01-20 TEK-01-20 TS-01-20 TSZ-012001
TW-01-25 TEK-01-25 TS-01-25 TSZ-012501
TW-01-30 TEK-01-30 TS-01-30 TSZ-013001
TW-02-20 TEK-02-20 When using the end caps, screws with a low screw head must be
TW-02-25 TEK-02-25 used to attach the rail.
TW-02-30 TEK-02-30
TW-04-09 TEK-04-09
TW-04-12 TEK-04-12
TW-04-15 TEK-04-15
1
T linear guide system can be readjusted. This should always take place
when there is no load on the carriage.
1 fter removing the protective cover, loosen the lockn uts Width
A
across flats:
2
– less clearance
2
Adjust the bearing clearance for the 3 guide points with an Allen
key – Allen key size:
+ more clearance
3
3
Check the clearance of the carriage after adjusting the 3 levels. If it
is sufficient, tighten the locknuts and put on the cover.
4
There is a danger that excessive reduction of the clearances can
seize the sliding pads and that the clearance cannot be reset simply
by loosening the adjustment screws. The sliding pads are then
vertical guide left
4
hard against the readjusting spring. You must have already loosened
the respective adjustment screws. Use the correct size pin for this
purpose:
1
is bigger than 0.1 mm and the system is unloaded.
2
locked
After the carriage is on the rail, remove the keys by turning them
2
counterclockwise 90° and pull out. The clearance will then be adjust-
ed automatically.
3
unlocked
For the exact calculation of the Linear Guide System it is essential to find out whether the position of the forces is within the allowable limits, and if the
gliding element where the highest forces occur is not overloaded. The calculation of the necessary driving force and the maximum speed allowed is
important. Each mounting version requires a different formula for calculation. Factors concerning shocks and acceleration forces are not included in the
calculation, therefore the maximum load and allowable load must be monitored.
10,0
5,0
TW-01-30
TW-01-25
2,0
TW-01-20
1,0
Permissible mean speed [m/s]
0,5
TW-01-15
0,2
0,1
10 20 50 100 200 500 1.000 2.000
Bearing load (center) [N]
Diagram 04: Diagram to determine the maximum permissible speed for the calculated bearing load
Recommended Procedure:
1st Step
Select the mounting version:
● horizontal
1 rail and 1 carriage
1 rail and 2 carriages
2 rails and 4 carriages
2nd Step
Check to see whether the maximum distances of the applied forces are within the permissible values (see Maximum permissible distances.)
Fa
az
ay Floating
Bearing Fs sx
sx Fa
az WX
Fs Zero Point ay
sz
Zero Point
y x y
z x
b z
Fixed Bearing
3rd Step:
Calculate the necessary drive force
3.1 Center of gravity in x and z 3.2 Center of gravity in z direction 3.3 Center of gravity in x direction
direction inside the carriage(s) outside of the carriage(s) outside of the carriage(s)
µ 2µ K7 2µ K4
Fa1 = · Fs Fa2 = · Fs Fa3 = · Fs
1– 2µ K3 1– 2µ K3 1– 2µ K3 – 2µ K1
If the position of the center of gravity is not specified: Fa = MAX (Fa1, Fa2, Fa3)
4th Step:
Calculate the maximum bearing load
4.1 Maximum bearing load in the y direction 4.2 Maximum bearing load in the z direction
Fy
max =
(
2 Fs 2 K4
Zw Zw
+ 0,5
)( •
Zw2 )
K7 + 0,5 +
2 Fa K1
Fz max =
Zw2
4 Fa K3
5th Step:
Check calculated load for both y and z with table on page 990 - Maximum permissible load for Fy max & Fz max. This table illustrates the maximum
permissible load on a single gliding element from the DryLin® T carriage. Evaluating the maximum load on a single gliding element establishes a safety
factor for the linear system. ➤ Page 990
6th Step:
Determine the maximum permissible speed for the calculated load from Step No. 4 ➤ Page 990
Recommended Procedure:
1st Step
Select the mounting version:
● side-mounting
1 rail and 1 carriage
1 rail and 2 carriages
2 rails and 4 carriages
2nd Step
Check to see whether the maximum distances of the applied forces
WX
are within the permissible values (see Maximum permissible distances.)
Maximum permissible distances between acting forces: Zero Point
z sx sy
Fixed
y Bearing sx
x az
Zero Point sy Fa Fs
ay
Fs
Fa
b
az ay
Floating
Bearing
x
3rd Step:
Calculate the necessary drive force
First, two calculations must be made:
4th Step:
Calculate the maximum bearing load
4.1 Maximum bearing load in the y direction 4.2 Maximum bearing load in the z direction
Fy max =
Fs K6 2 Fa K1
+
Zw Zw2
Fz
max =
(
2 Fs 2 K4
Zw Zw Zw2
+ 0.5 +
)
4 Fa K3
5th Step:
Check calculated load for both y and z with table on page 990 - Maximum permissible load for Fy max & Fz max. This table illustrates the maximum
permissible load on a single gliding element from the DryLin® T carriage. Evaluating the maximum load on a single gliding element establishes a safety
factor for the linear system. ➤ Page 990
6th Step:
Determine the maximum permissible speed for the calculated load from Step No. 4 ➤ Page 990
Recommended Procedure:
1st Step
Select the mounting version:
● vertical
1 rail and 1 carriage
1 rail and 2 carriages
2 rails and 4 carriages
2nd Step
Check to see whether the maximum distances of the applied forces
are within the permissible values (see Maximum permissible distances.)
Maximum permissible distances between acting forces: b
Floating
Bearing
Fixed
az Bearing
ay
Fa Fa
az
ay Zero Point
Zero Point
sy sy
WX
Fs
x
Fs
z z
y
sz x
y
Variation: 1 Rail, 1 Carriage
sy + sz < 2 Lx - Y0 Variation: 1 Rail, 2 Carriages
Variation: 2 Rails, 4 Carriages
ay + az < 2 Lx - Y0
sy + sz < 2 wx - Y0
sy < 5 Zm
ay + az < 2 wx - Y0
sz < 5 Zm
3rd Step:
Calculate the necessary drive force
First, four calculations must be made:
2µ (sz+sy+Y0) – wx 2µ (sz – sy – Y0) – wx
Fa1 = · Fs Fa3= · Fs
2µ (az+ay+Y0) – wx 2µ (az – ay – Y0) – wx
2µ (– sz+sy+Y0) – wx 2µ (sz+sy+Y0) + wx
Fa2= · Fs Fa4= · Fs
2µ (– az+ay+Y0) – wx 2µ (az+ay+Y0) + wx
The drive force Fa corresponds to the calculated maximum value Fa = MAX (Fa1, Fa2, Fa3, Fa4)
4th Step:
Calculate the maximum bearing load
4.1 Maximum bearing load in the y direction 4.2 Maximum bearing load in the z direction
Fy max = Fa
wx Zw2
ay + Y0
– Fs K2 •
2
Fz max = Fa
wx Zw2
az
– Fs K5 •
4
5th Step:
Check calculated load for both y and z with table on page 990 - Maximum permissible load for Fy max & Fz max. This table illustrates the maximum
permissible load on a single gliding element from the DryLin® T carriage. Evaluating the maximum load on a single gliding element establishes a safety
factor for the linear system. ➤ Page 990
6th Step:
Determine the maximum permissible speed for the calculated load from Step No. 4 ➤ Page 990
995
DryLin® R Round Shaft Guide Systems - Advantages
tive to
erna
Alt
Self-lubricating round
shaft guide systems –
DryLin® R
s
ball bearing
100% self-lubricating
Dimensionally interchangeable with standard
recirculating ball bearings
Large variety of housing options
Linear adapter and complete Shafts, shaft-end supports and accessories available
housing made from aluminum Replaceable bearing liner
300 series stainless steel housing available
8 shaft materials
8 versions
Inner-Ø up to 60 mm
Flange bearing
Easy to fit
Round or square options available
Standard or twin flange designs
Quad block
Closed or open design options
Quad block housing with 4 bearing liners
Floating bearing available
DryLin® R linear plain bearings on supported aluminum This saw mill uses a DryLin® linear bearing with iglide® J plastic
shafts are used in the guide for this cutting table. The DryLin® liner for the angle stops.
components stand up to the high levels of dust and dirt, and
offer accurate, smooth operation.
This heavy duty application has run reliably for more than three Despite the high stresses from abrasive particles and powder
years thanks to DryLin® RJUM-01 linear bearings particles, this compactor unit can extend maintenance-free
uptime by up to two years after switching to DryLin® R linear
bearings.
Maintenance-free, precise, compact, and wear resistant To enable fast, and precise adjustment of a production line
bearing liners were mounted directly in the passages of this without the need for downtime, DryLin® precision linear guides
machine’s frame. were utilized.
➤ www.igus.com/DryLin-CAD
A180 or T500 (X)* materials, which offer technical advantages as Split linear bearings
well as cost savings. Plastic bearings are well suited for applications Applications on the edge of technical feasibility or in extreme
where machine components are primarily stainless steel, such as in environments often require frequent replacement of linear bearings.
food production and packaging equipment, as well as applications DryLin® linear bearings can provide significant increases in service
where weight savings are critical. DryLin® R linear plain bearings life, and even when replacement is necessary, the replaceable
are designed to fit housings with our recommended tolerances, bearing liners can offer substantial cost savings. Replacing only the
secured via circlips in the same way as ball bearings. bearing’s liner can reduce maintenance time by 90%. The range of
split bearing housings are easily opened, and the split shell means
that the shafts are able to stay in place while a new bearing and
liner can be installed around the shaft, keeping installation time to
a minimum.
The "all-rounder" – The specialist – The extreme – The marathon runner – FDA compliant –
iglide® J iglide® J200 iglide® T500 (X) iglide® E7 iglide® A180
Aluminum, Hardened stainless steel Steel
Optimal shaft material(s) all shaft materials
hard anodized Hard chromed plated steel stainless steel shaft
all shaft materials
-40°F to +194°F -40°F to +194°F -148°F to +482°F -40°F to +194°F -40°F to +194°F
Application temperature (-40°C to +90°C) (-40°C to +90°C) (-100°C to +250°C) (-40°C to +90°C) (-40°C to +90°C)
Aluminum, Steel hard Steel
Best coefficient of friction with Steel shaft
hard anodized chrome-plated stainless steel shaft
Stainless steel shaft
Aluminum, hard Aluminum, Hardened Steel
Maximum life time anodized hard anodized stainless steel stainless steel shaft
Stainless steel shaft
Permissible stat. surface pressure 35 MPa 23 MPa 150 MPa 18 MPa 28 MPa
Moisture absorption 1.3% weight 0.7% weight 0.5% weight < 0.1% weight 0.2% weight
Volume resistance > 1013 Ωcm > 108 Ωcm < 105 Ωcm > 109 Ωcm > 1012 Ωcm
The spherical DryLin® adapters can compensate With built in clearances and the use of O-rings, the The self-aligning DryLin® R bearings of the 06 LL
for alignment errors. A hard-anodization protects self-aligning DryLin® R bearings of the 03 Design design series can compensate parallelism errors
the aluminum adapter from wear. Series can compensate for parallelism errors. up to ± .12” (3mm).
Design tips for DryLin® linear plain bearings: Recommended shaft-tolerance: h6–h10
The values for "Fmax." relate to the performance of the iglide® Roughness [Ra]: 0.15–0.6
liners , and is not intended as as selection tool for the calculation Guide shafts, round/supported ➤ shafts, page 1099
of an application. The maximum carrying capacity of the entire
bearing system depends on the geometry, housing material, Recommended mounting hole: H7
connection including the screws, and requires a separate inspection. Linear Plain Bearing RJUM-01/03, TJUM-01/03, RJM,
For a detailed analysis, please use our online configurator at RJMP, RJ260(U)M02, Pressfit bearing WLM, WLFM
➤ www.igus.com/DryLin-expert
Solid plastic bearings: Linear plain bearings: Compact bearing: Linear plain bearings:
RJMP RJUM-02 RJ260 (UM-02) OJUM-01, OJUM-03, OJUI-01,
Easy assembly by soft slip-fit Secured by pressfitting in steel Axial saving and press fit into OJUI-03
Secured by DIN 471 or 472 housing bore H7 or aluminum housing bore H7 Secure the bearing with set
circlips, metric types (not included housing bore K7 Alternatively, the adapter can be screws (not included in delivery)
in delivery) Alternatively, the adapter can be glued with commercially available
glued with commercially available 2-component adhesive into a
2-component adhesive housing
Quad block: RQA, RGA Linear housing: Quad block: OQA, OGA, linear Pillow block: RJUM/E/T-05,
twin design: RTA RGAS housing: OGAS, tandem design: RJUM-06/-LL, OJUM/E-06/-LL,
The bearing in the housing is The bearing in the housing is OTA flange housing: FJUM/T-01/02
secured using DIN 472 circlips secured using DIN 471 circlips The bearings of the housings quad block: RGA, OGA, twin
are secured using set screws design: RTA, OTA, linear
housing: RGAS, OGAS
Mounting screws of the housing
DIN 912-8.8; circlips according to
DIN 7980
3D-CAD files, prices and delivery time ➤ www.igus.com/drylinR 1003
DryLin® R
round
shaft guide DryLin® R Linear - Product range
systems
Closed, long design
d2
d2d2
Order key
zz z Type Size
d
d1d1 1 J U I - 01 - 10
rb1
t
r
b1
b1
t
t
r
Standard
iglide® J
Other iglide® material options:
Liner
Inch
iglide® J200: Best for aluminum shafts
d1
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance* d2 b1 r t z
Size -0.004 -0.004 -0.020
-0.008
B/2
Size Max. Min. *h10 +0.002 +0.004 +0.02 +0.008
ØZ
JUI-01-06 3/8 .4680 .4684 .875 .1250 .031 .039 .102
JUI-01-08 1/2 .5940 .5934 1.250 .1250 .0391 .059 .122
f
JUI-01-10 5/8 .7190 .7184 1.500 .1406 .0391 .067 .142
JUI-01-12 3/4 .8755 .8747 1.625 .1875 .0391 .079 .142
Ø di
JUI-01-16 1 1.1255 1.1247 2.250 .1875 .0391 .079 .161
JUI-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .0391 .079 .161
t
d2 d2
Order key
Y YY Y 2:1
Y 2:1
z z
Type Size
d1 d1 d
1
J U I O - 01 - 10
b1
b1
t
r
t
r
Standard
iglide® J
Other iglide® material options:
Open
Liner
iglide® J200: Best for aluminum shafts
Inch
d1
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance d2 b1 W r t z
Size -0.004 -0.004 -0.020
-0.008
t
JUIO-01-12 3/4 .8755 .8747 1.625 .1875 .039 .079 .142 0.492
Ø di
JUIO-01-16 1 1.1255 1.1247 2.250 .1875 .039 .079 .161 0.630
JUIO-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .039 .079 .161 0.709
JUIO-01-24 1 1/2 1.6568 1.6558 3.000 .2500 .062 .089 .200 0.866
ØZ
JUIO-01-32 2 2.1881 2.1871 4.000 .2813 .062 .098 .240 1.181
d2
d2d2
Order key
zz z Type Size
d
d1d1 1 J U I - 20 - 10
rb1
t
r
b1
b1
t
t
r
Low Clearance
iglide® J
Other iglide® material options:
iglide® J200: Best for aluminum shafts
Liner
Inch
d1
Dimensions [inch]
Part No. Nominal Tolerance* d2 b1 r t z
Size -0.004 -0.004 -0.020
-0.008
B/2
Size Max. Min. *h10 +0.002 +0.004 +0.02 +0.008
ØZ
JUI-20-06 3/8 .4680 .4684 .875 .1250 .031 .039 .102
JUI-20-08 1/2 .5940 .5934 1.250 .1250 .0391 .059 .122
f
JUI-20-10 5/8 .7190 .7184 1.500 .1406 .0391 .067 .142
JUI-20-12 3/4 .8755 .8747 1.625 .1875 .0391 .079 .142
Ø di
JUI-20-16 1 1.1255 1.1247 2.250 .1875 .0391 .079 .161
JUI-20-20 1 1/4 1.4068 1.4058 2.625 .1875 .0391 .079 .161
t
d2 d2
Order key
Y YY Y 2:1
Y 2:1
z z
Type Size
d1 d1 d
1
J U I O - 20 - 10
b1
b1
t
r
t
r
Low clearance
Other iglide® material options:
iglide® J
iglide® J200: Best for aluminum shafts
Open
Liner
Inch
d1
Dimensions [inch]
Part No. Nominal Tolerance d2 b1 W r t z
Size -0.004 -0.004 -0.020
-0.008
JUIO-20-06 3/8 .0008- .0012 0.4684 0.846 0.250 .1250 .0311 .0866
JUIO-20-08 1/2 .0008- .0012 0.5934 1.220 0.394 .1250 .0391 .1024
JUIO-20-10 5/8 .0008- .0012 0.7184 1.460 0.433 .1406 .0391 .1181
JUIO-20-12 3/4 .0008- .0012 0.8747 1.575 0.492 .1875 .0391 .1339
JUIO-20-16 1 .0008- .0012 1.1247 2.205 0.630 .1875 .0391 .1496
JUIO-20-20 1 1/4 .0010 - .0016 1.4058 2.573 0.709 .1875 .0391 .1496
JUIO-20-24 1 1/2 .0010 - .0016 1.6558 2.953 0.866 .2500 .0625 .1811
JUIO-20-32 2 .0012- .0020 2.1871 4.937 1.181 .2813 .0625 .2280
t
JUIO-20-12 3/4 .8755 .8747 1.625 .1875 .039 .079 .142 0.492
Ø di
JUIO-20-16 1 1.1255 1.1247 2.250 .1875 .039 .079 .161 0.630
JUIO-20-20 1 1/4 1.4068 1.4058 2.625 .1875 .039 .079 .161 0.709
JUIO-20-24 1 1/2 1.6568 1.6558 3.000 .2500 .062 .089 .200 0.866
ØZ
JUIO-20-32 2 2.1881 2.1871 4.000 .2813 .062 .098 .240 1.181
OJUI-01, OJUI-03
400 series stainless
Maximum static psi = 5,075
d2d2d2
Order key
zz z
Type Size
d1d1 d1
J 2 0 0 U I - 01 - 10
b1
b1
b1
t
t
t
r
r
r
iglide® J200
Standard
Other iglide® material options:
Liner
Inch
iglide® J: All around material
d1
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance* d2 b1 r t z
Size -0.004 -0.004 -0.020
-0.008
B/2
Size Max. Min. *h10 +0.002 +0.004 +0.02 +0.008
ØZ
J200UI-01-06 3/8 .4680 .4684 .875 .1250 .031 .039 .102
J200UI-01-08 1/2 .5940 .5934 1.250 .1250 .0391 .059 .122
f
J200UI-01-10 5/8 .7190 .7184 1.500 .1406 .0391 .067 .142
J200UI-01-12 3/4 .8755 .8747 1.625 .1875 .0391 .079 .142
Ø di
J200UI-01-16 1 1.1255 1.1247 2.250 .1875 .0391 .079 .161
J200UI-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .0391 .079 .161
t
J 2 0 0 U I O - 01 - 10
t
b1 r
t
r
iglide® J200
Standard
Other iglide® material options:
iglide® J: All around material
Open
Liner
Inch
iglide® E7: Best for steel/stainless steel shafts
d1
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance d2 b1 W r t z
Size -0.004 -0.004 -0.020
-0.008
t
J200UIO-01-12 3/4 .8755 .8747 1.625 .1875 .039 .079 .142 0.492
Ø di
J200UIO-01-16 1 1.1255 1.1247 2.250 .1875 .039 .079 .161 0.630
J200UIO-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .039 .079 .161 0.709
J200UIO-01-24 1 1/2 1.6568 1.6558 3.000 .2500 .062 .089 .200 0.866
ØZ
J200UIO-01-32 2 2.1881 2.1871 4.000 .2813 .062 .098 .240 1.181
d2d2d2
Order key
zz z
Type Size
d1d1 d1
E 7 U I - 01 - 10
b1
b1
b1
t
t
t
r
r
r
iglide® E7
Standard
Other iglide® material options:
iglide® J: All around material
Liner
Inch
iglide® J200: Best for aluminum shafts
d1
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance* d2 b1 r t z
Size -0.004 -0.004 -0.020
-0.008
B/2
Size Max. Min. *h10 +0.002 +0.004 +0.02 +0.008
ØZ
E7UI-01-06 3/8 .4680 .4684 .875 .1250 .031 .039 .102
E7UI-01-08 1/2 .5940 .5934 1.250 .1250 .0391 .059 .122
f
E7UI-01-10 5/8 .7190 .7184 1.500 .1406 .0391 .067 .142
E7UI-01-12 3/4 .8755 .8747 1.625 .1875 .0391 .079 .142
Ø di
E7UI-01-16 1 1.1255 1.1247 2.250 .1875 .0391 .079 .161
E7UI-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .0391 .079 .161
t
d2 d2
Order key
Y YY Y 2:1
Y 2:1
z z
Type Size
d1 d1 d
1
E 7 U I O - 01 - 10
b1
b1
t
r
t
r
iglide® E7
Other iglide® material options:
Standard
iglide® J: All around material
Open
Liner
Inch
iglide® J200: Best for aluminum shafts
d1
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions [inch]
Part No. Nominal Tolerance d2 b1 W r t z
Size -0.004 -0.004 -0.020
-0.008
t
E7UIO-01-12 3/4 .8755 .8747 1.625 .1875 .039 .079 .142 0.492
Ø di
E7UIO-01-16 1 1.1255 1.1247 2.250 .1875 .039 .079 .161 0.630
E7UIO-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .039 .079 .161 0.709
E7UIO-01-24 1 1/2 1.6568 1.6558 3.000 .2500 .062 .089 .200 0.866
ØZ
E7UIO-01-32 2 2.1881 2.1871 4.000 .2813 .062 .098 .240 1.181
steel
Maximum static psi = 5,075
d2
Y Y 2:1 Order key
z Type Size
d1 T U I - 01 - 10
b1
t
r
Standard
Other iglide® material options:
Liner
iglide® J: All around material
Inch
d1
iglide® J200: Best for aluminum shafts
iglide® E7: Best for steel/stainless steel shafts
Dimensions [inch]
Part No. Nominal Tolerance* d2 b1 r t z
Size -0.004 -0.004 -0.020
-0.008
ØZ
Part No. Nominal di B r t f z
Size Max. Min. *h10 +0.002 +0.004 +0.02 +0.008
f
TUI-01-08 1/2 .5940 .5934 1.250 .1250 .0391 .059 .122
TUI-01-12 3/4 .8755 .8747 1.625 .1875 .0391 .079 .142
Ø di
TUI-01-16 1 1.1255 1.1247 2.250 .1875 .0391 .079 .161
TUI-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .0391 .079 .161
t
TUI-01-24 1 1/2 1.6568 1.6558 3.000 .2500 .051 .098 .200
d2 d2
Order key
YY YY2:1
2:1
Type Size
z
z
d1
T U I O - 01 - 10
b1
d1
r
d
b1
t
r
Standard
Diameter
Other iglide® material options:
Open
Liner
iglide® J: All around material
Inch
2-pieces per part number
iglide® J200: Best for aluminum shafts
iglide® E7: Best for steel/stainless steel shafts
Dimensions [inch]
Part No. Nominal Tolerance d2 b1 W r t z
Size -0.004 -0.004 -0.020
-0.008
f
TUIO-01-10 5/8 .7190 .7184 1.500 .1406 .039 .067 .142 0.433
TUIO-01-12 3/4 .8755 .8747 1.625 .1875 .039 .079 .142 0.492
TUIO-01-16 1 1.1255 1.1247 2.250 .1875 .039 .079 .161 0.630 Ø di
TUIO-01-20 1 1/4 1.4068 1.4058 2.625 .1875 .039 .079 .161 0.709
t
TUIO-01-24 1 1/2 1.6568 1.6558 3.000 .2500 .062 .089 .200 0.866
TUIO-01-32 2 2.1881 2.1871 4.000 .2813 .062 .098 .240 1.181
*European part numbers for the high temperature liner r
begin with X. Example XUIO-...
W
According to igus® testing method ➤ Page 1096
78)
TJUI-01/-03
Order key
dn
d2
d1
1,5 x 30°
Type Size
R J I-01-10
B1
B
s
Standard
Diameter
iglide® J
Closed
Inch
Dimension equivalent to the standard
for recirculating ball bearings
Assembly by pressfitting iglide® material options:
➤ Press-in forces: see table iglide® J: All around material
Technical Data
Part No. Shaft d1-Tolerance78) Fmax. dyn.82) Fmax. stat82) Housing bore Weight Pressfit force83)
Ø after pressfit P = 2.5 MPa P = 17.5 MPa Recommendations
in housing [N] [N] Min Max [g] [N]
RJI-01-06 3/8 +0.0010 +0.0024 265 1.855 0.6250 0.6257 3 400
RJI-01-08 1/2 +0.0013 +0.0030 505 3.535 0.8750 0.8758 8.8 700
RJI-01-10 5/8 +0.0013 +0.0030 755 5.285 1.1250 1.1258 17.4 1,300
RJI-01-12 3/4 +0.0016 +0.0036 982 6.877 1.2500 1.2510 22.2 1,100
RJI-01-16 1 +0.0016 +0.0036 1.815 12.705 1.5620 1.5630 42.5 1,500
RJI-01-20 1 1/4 +0.0020 +0.0044 2.645 18.515 2.0000 2.0010 81.1 3,500
RJI-01-24 1 1/2 +0.0020 +0.0044 3.630 25.410 2.3750 2.3760 127.1 4,500
RJI-01-32 2 +0.0024 +0.0053 6.452 45.167 3.0000 3.0010 249 4,200
Dimensions [inch]
Part No. d1 d2 B B1 s dn
RJI-01-06 3/8 0.625 0.875 0.689 0.0410 0.587
RJI-01-08 1/2 0.875 1.25 1.0125 0.0480 0.82
RJI-01-10 5/8 1.125 1.50 1.0950 0.0580 1.0600
RJI-01-12 3/4 1.25 1.625 1.25 0.0580 1.177
RJI-01-16 1 1.5625 2.25 1.864 0.0700 1.471
RJI-01-20 1 1/4 2.00 2.625 1.984 0.0700 1.889
RJI-01-24 1 1/2 2.375 3.00 2.39 0.0890 2.241
RJI-01-32 2 3.00 4.00 3.163 0.1050 2.839
78)
According to igus® testing method ➤ Page 1096
82)
Design standards ➤ Page 1001
83)
Applies to room temperature pressfit decreases with time depending on the temperature
Please note: Installation instructions ➤ Page 1003
dn Order key
d2
d1
B1
R J I P - 01-10
B
s
Low clearance
Standard
Diameter
Easy assembly by slip-fit
iglide® J
Closed
Reduced bearing clearance
Inch
Temperature range -4°F to +140°F (-20 °C to +60 °C)
Technical Data
Part No. Shaft d1-Tolerance78) Fmax. dyn.82) Fmax. stat.82) Housing bore Weight
Ø P = 2.5 MPa P = 2.5 MPa Recommendations
[N] [N] Min Max [g]
RJIP-01-04 1/4 + 0.00 +0.0014 180 1.267 0.5000 0.5007 2
RJIP-01-06 3/8 + 0.00 +0.0014 265 1.855 0.6250 0.6257 2
RJIP-01-08 1/2 + 0.00 +0.0017 505 3.535 0.8750 0.8758 4
RJIP-01-10 5/8 + 0.00 +0.0017 755 5.285 1.1250 1.1258 7
RJIP-01-12 3/4 + 0.00 +0.0020 982 6.877 1.2500 1.2510 9
RJIP-01-16 1 + 0.00 +0.0020 1.815 12.705 1.5620 1.5630 13
RJIP-01-20 1 1/4 + 0.00 +0.0024 2.645 18.515 2.0000 2.0010 24
Dimensions [inch]
Part No. d1 d2 B B1 s dn
RJIP-01-04 1/4 0.4999 0.74803 0.5188 0.0409 0.4669
RJIP-01-06 3/8 0.625 0.875 0.689 0.0410 0.587
RJIP-01-08 1/2 0.875 1.25 1.0125 0.0480 0.82
RJIP-01-10 5/8 1.125 1.50 1.0950 0.0580 1.0600
RJIP-01-12 3/4 1.25 1.625 1.25 0.0580 1.177
RJIP-01-16 1 1.5625 2.25 1.864 0.0700 1.471
RJIP-01-20 1 1/4 2.00 2.625 1.984 0.0700 1.889
o o s s
Order key
Type Size
do
do
dn
dn
R J U I - 01-10
e e
B1 B1 d1 d1
iglide® Material
B B d2 d2
Standard
Diameter
Closed
Dimensionally interchangeable with linear ball bearings
Liner
Inch
Liner made of iglide® J: Temperature range -40°F to +194°F
(-40°C to +90°C) JUI-01 (standard)
T500 liner optional for chemicals/high temps
up to 482°F (250°C) for steel housing, 356°F (180°C) for iglide® material options:
iglide® J: All around material
aluminum
iglide® J200: Best for aluminum shafts
Suitable shafting for iglide® J: DryLin® AWI aluminum,
iglide® E7: Best for steel/stainless steel shafts
case-hardened, 300 series stainless Best shafting for T500: iglide® T500 (X)*: For high temps up to 356°F (180°C)
hard-chrome and hard-stainless steel in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
RJZI-01-04* 1/4 .0016 - .0032 .5000 .7500 .518 .0410 .4670 .125 .0800 .3990
RJUI-01-06 3/8 .0016 - .0032 .6250 .8700 .644 .0410 .5870 .243 .0610 .5660
RJUI-01-08 1/2 .0016 - .0032 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
RJUI-01-10 5/8 .0016 - .0032 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
RJUI-01-12 3/4 .0016 - .0032 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
RJUI-01-16 1 .0016 - .0032 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
RJUI-01-20 1-1/4 .0020 - .0041 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
RJUI-01-24 1-1/2 .0020 - .0041 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
RJUI-01-32 2 .0024 - .0051 3.0000 4.0000 3.222 .1110 2.8390 1.000 .1890 2.7750
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. RJZI-01-04* 135 946
1/4 0.5000 0.5007 RJUI-01-06 118 828
3/8 0.6250 0.6257 RJUI-01-08 225 1575
1/2 0.8750 0.8758 RJUI-01-10 338 2365
5/8 1.1250 1.1258 RJUI-01-12 439 3077
3/4 1.2500 1.2510 RJUI-01-16 811 5678
1 1.5625 1.5635 RJUI-01-20 1184 8287
1-1/4 2.0000 2.0010 RJUI-01-24 1622 11358
1-1/2 2.3750 2.3760 RJUI-01-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
o o s s
Order key
do Type Size
do
dn
dn
R J U I - 21-10
e e
B1 B1 d1 d1
iglide® Material
Low clearance
B B d2 d2
Diameter
Closed
Dimensionally interchangeable with linear ball bearings
Liner
Inch
Liner made of iglide® J: Temperature range -40°F to
+194°F (-40°C to +90°C) JUI-20 (low clearance)
T500 liner optional for chemicals/high temps
(up to 482°F for steel housing, 356°F for aluminum) iglide® material options:
iglide® J: All around material
Suitable shafting for iglide® J: DryLin® AWI aluminum,
iglide® J200: Best for aluminum shafts
case-hardened, 300 series stainless Best shafting for
iglide® E7: Best for steel/stainless steel shafts
T500: hard-chrome and hard-stainless steel iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
RJUI-21-06 3/8 .0008 - .0016 .6250 .8700 .644 .0410 .5870 .243 .0610 .5660
RJUI-21-08 1/2 .0008 - .0016 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
RJUI-21-10 5/8 .0008 - .0016 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
RJUI-21-12 3/4 .0008 - .0016 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
RJUI-21-16 1 .0008 - .0016 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
RJUI-21-20 1-1/4 .0010 - .0021 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
RJUI-21-24 1-1/2 .0010 - .0021 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
RJUI-21-32 2 .0012 - .0026 3.0000 4.0000 3.222 .1110 2.8390 1.000 .1890 2.7750
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. RJUI-21-06 118 828
3/8 0.6250 0.6257 RJUI-21-08 225 1575
1/2 0.8750 0.8758 RJUI-21-10 338 2365
5/8 1.1250 1.1258 RJUI-21-12 439 3077
3/4 1.2500 1.2510 RJUI-21-16 811 5678
1 1.5625 1.5635 RJUI-21-20 1184 8287
1-1/4 2.0000 2.0010 RJUI-21-24 1622 11358
1-1/2 2.3750 2.3760 RJUI-21-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
R
o s
Order key
Type Size
do
dn
ds
R J U I - 03-10
e
B1 d1
iglide® Material
B d2
Self-aligning
Anodized aluminum adapter
Diameter
Dimensionally interchangeable with linear ball bearings
Closed
Liner
Equipped with liner made of iglide® J
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
JUI-01 (standard)
T500 liner optional for chemicals/high temps iglide® material options:
(up to 482°F for steel housing, 356°F for aluminum) iglide® J: All around material
Suitable shafting for iglide® J: DryLin® AWI aluminum, iglide® J200: Best for aluminum shafts
case-hardened, 300 series stainless Best shafting for iglide® E7: Best for steel/stainless steel shafts
T500: hard-chrome and hard-stainless steel iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance** d2 B B1 s ds dn do o e
Size ISO h8 ISO h10 ISO H10 ISO h10 -0.004
RJZI-03-04* 1/4 .0016 - .0032 .4921 .7460 .5270 .0410 .4803 .4660 .3990 .0800 .1250
RJUI-03-06 3/8 .0016 - .0032 .6173 .8713 .6520 .0410 .6055 .5870 .5240 .0610 .2430
RJUI-03-08 1/2 .0016 - .0032 .8673 1.2461 .9870 .0520 .8556 .8200 .7120 .1250 .2815
RJUI-03-10 5/8 .0016 - .0032 1.1173 1.4961 1.1360 .0620 1.1055 1.0600 .9620 .1250 .3125
RJUI-03-12 3/4 .0016 - .0032 1.2421 1.6173 1.1980 .0620 1.2300 1.1770 1.0870 .1250 .3125
RJUI-03-16 1 .0016 - .0032 1.5547 2.2421 1.7890 .0740 1.5271 1.4710 1.3990 .1250 .5000
RJUI-03-20 1-1/4 .0020 - .0041 1.9881 2.6173 2.0390 .0740 1.9606 1.8890 1.8370 .1250 .6250
RJUI-03-24 1-1/2 .0020 - .0041 2.3634 2.9921 2.4630 .0950 2.3358 2.2410 2.1520 .1620 .7500
RJUI-03-32 2 .0024 - .0051 2.9881 3.9921 3.2490 .1110 2.9606 2.8390 2.7750 .1890 1.0000
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. RJZI-03-04* 135 946
1/4 0.5000 0.5007 RJUI-03-06 118 828
3/8 0.6250 0.6257 RJUI-03-08 225 1575
1/2 0.8750 0.8758 RJUI-03-10 338 2365
5/8 1.1250 1.1258 RJUI-03-12 439 3077
3/4 1.2500 1.2510 RJUI-03-16 811 5678
1 1.5625 1.5635 RJUI-03-20 1184 8287
1-1/4 2.0000 2.0010 RJUI-03-24 1622 11358
1-1/2 2.3750 2.3760 RJUI-03-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
do Type Size
do
dn
dn
R J200 U I - 01 - 10
e e
B1 B1 d1 d1
iglide® Material
B B d2 d2
Diameter
Standard
Dimensionally interchangeable with linear ball bearings
Closed
Liner
Equipped with liner made of iglide® J200
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
J200UI-01 (standard)
T500 liner optional for chemicals/high temps iglide® material options:
(up to 482°F for steel housing, 356°F for aluminum) iglide® J: All around material
Ideal for aluminum shafting iglide® J200: Best for aluminum shafts
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
RJ200UI-01-06 3/8 .0016 - .0032 .6250 .8700 .644 .0410 .5870 .243 .0610 .5660
RJ200UI-01-08 1/2 .0016 - .0032 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
RJ200UI-01-10 5/8 .0016 - .0032 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
RJ200UI-01-12 3/4 .0016 - .0032 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
RJ200UI-01-16 1 .0016 - .0032 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
RJ200UI-01-20 1-1/4 .0020 - .0041 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
RJ200UI-01-24 1-1/2 .0020 - .0041 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
RJ200UI-01-32 2 .0024 - .0051 3.0000 4.0000 3.222 .1110 2.8390 1.000 .1890 2.7750
Housing Bore
Recommendations Load Data
Nominal Part No. F max, dynamic F max, static
p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max.
RJ200UI-01-06 118 828
3/8 0.6250 0.6257
RJ200UI-01-08 225 1575
1/2 0.8750 0.8758
RJ200UI-01-10 338 2365
5/8 1.1250 1.1258
RJ200UI-01-12 439 3077
3/4 1.2500 1.2510
RJ200UI-01-16 811 5678
1 1.5625 1.5635
RJ200UI-01-20 1184 8287
1-1/4 2.0000 2.0010
RJ200UI-01-24 1622 11358
1-1/2 2.3750 2.3760
RJ200UI-01-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
R
o s
Order key
Type Size
do
dn
ds
R J200 U I - 03 - 10
e
B1 d1
iglide® Material
B d2
Self-aligning
Anodized aluminum adapter
Diameter
Dimensionally interchangeable with linear ball bearings
Closed
Equipped with liner made of iglide® J200
Liner
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
J200UI-01 (standard)
T500 liner optional for chemicals/high temps
iglide® material options:
(up to 482°F for steel housing, 356°F for aluminum)
iglide® J: All around material
Suitable shafting: DryLin® AWI aluminum
iglide® J200: Best for aluminum shafts
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance** d2 B B1 s ds dn do o e
Size ISO h8 ISO h10 ISO H10 ISO h10 -0.004
RJ200UI-03-06 3/8 .0016 - .0032 .6173 .8713 .6520 .0410 .6055 .5870 .5240 .0610 .2430
RJ200UI-03-08 1/2 .0016 - .0032 .8673 1.2461 .9870 .0520 .8556 .8200 .7120 .1250 .2815
RJ200UI-03-10 5/8 .0016 - .0032 1.1173 1.4961 1.1360 .0620 1.1055 1.0600 .9620 .1250 .3125
RJ200UI-03-12 3/4 .0016 - .0032 1.2421 1.6173 1.1980 .0620 1.2300 1.1770 1.0870 .1250 .3125
RJ200UI-03-16 1 .0016 - .0032 1.5547 2.2421 1.7890 .0740 1.5271 1.4710 1.3990 .1250 .5000
RJ200UI-03-20 1-1/4 .0020 - .0041 1.9881 2.6173 2.0390 .0740 1.9606 1.8890 1.8370 .1250 .6250
RJ200UI-03-24 1-1/2 .0020 - .0041 2.3634 2.9921 2.4630 .0950 2.3358 2.2410 2.1520 .1620 .7500
RJ200UI-03-32 2 .0024 - .0051 2.9881 3.9921 3.2490 .1110 2.9606 2.8390 2.7750 .1890 1.0000
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. RJ200UI-03-06 118 828
3/8 0.6250 0.6257 RJ200UI-03-08 225 1575
1/2 0.8750 0.8758 RJ200UI-03-10 338 2365
5/8 1.1250 1.1258 RJ200UI-03-12 439 3077
3/4 1.2500 1.2510 RJ200UI-03-16 811 5678
1 1.5625 1.5635 RJ200UI-03-20 1184 8287
1-1/4 2.0000 2.0010 RJ200UI-03-24 1622 11358
1-1/2 2.3750 2.3760 RJ200UI-03-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
do Type Size
do
dn
dn
R E7 U I - 01 - 10
e e
B1 B1 d1 d1
iglide® Material
B B d2 d2
Diameter
Standard
Dimensionally interchangeable with linear ball bearings
Closed
Equipped with liner made of iglide® E7
Liner
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
E7UI-01 (standard)
T500 liner optional for chemicals/high temps
iglide® material options:
(up to 482°F for steel housing, 356°F for aluminum)
iglide® J: All around material
Suitable shafting: case-hardened, 300 series stainless,
iglide® J200: Best for aluminum shafts
hard-chrome and hard-stainless steel iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
RE7UI-01-06 3/8 .0016 - .0032 .6250 .8700 .644 .0410 .5870 .243 .0610 .5660
RE7UI-01-08 1/2 .0016 - .0032 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
RE7UI-01-10 5/8 .0016 - .0032 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
RE7UI-01-12 3/4 .0016 - .0032 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
RE7UI-01-16 1 .0016 - .0032 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
RE7UI-01-20 1-1/4 .0020 - .0041 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
RE7UI-01-24 1-1/2 .0020 - .0041 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
RE7UI-01-32 2 .0024 - .0051 3.0000 4.0000 3.222 .1110 2.8390 1.000 .1890 2.7750
Housing Bore
Recommendations Load Data
Nominal Part No. F max, dynamic F max, static
p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max.
RE7UI-01-06 118 828
3/8 0.6250 0.6257
RE7UI-01-08 225 1575
1/2 0.8750 0.8758
RE7UI-01-10 338 2365
5/8 1.1250 1.1258
RE7UI-01-12 439 3077
3/4 1.2500 1.2510
RE7UI-01-16 811 5678
1 1.5625 1.5635
RE7UI-01-20 1184 8287
1-1/4 2.0000 2.0010
RE7UI-01-24 1622 11358
1-1/2 2.3750 2.3760
RE7UI-01-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
R
o s
Order key
Type Size
do
dn
ds
R E7 U I - 03 - 10
e
B1 d1
B d2
iglide® Material
Self-aligning
Anodized aluminum adapter
Dimensionally interchangeable with linear ball bearings
Diameter
Closed
Equipped with liner made of iglide® E7
Liner
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
E7UI-01 (standard)
T500 liner optional for chemicals/high temps
(up to 482°F for steel housing, 356°F for aluminum) iglide® material options:
iglide® J: All around material
Suitable shafting: case-hardened, 300 series stainless,
iglide® J200: Best for aluminum shafts
hard-chrome and hard-stainless steel
iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance** d2 B B1 s ds dn do o e
Size ISO h8 ISO h10 ISO H10 ISO h10 -0.004
RE7UI-03-06 3/8 .0016 - .0032 .6173 .8713 .6520 .0410 .6055 .5870 .5240 .0610 .2430
RE7UI-03-08 1/2 .0016 - .0032 .8673 1.2461 .9870 .0520 .8556 .8200 .7120 .1250 .2815
RE7UI-03-10 5/8 .0016 - .0032 1.1173 1.4961 1.1360 .0620 1.1055 1.0600 .9620 .1250 .3125
RE7UI-03-12 3/4 .0016 - .0032 1.2421 1.6173 1.1980 .0620 1.2300 1.1770 1.0870 .1250 .3125
RE7UI-03-16 1 .0016 - .0032 1.5547 2.2421 1.7890 .0740 1.5271 1.4710 1.3990 .1250 .5000
RE7UI-03-20 1-1/4 .0020 - .0041 1.9881 2.6173 2.0390 .0740 1.9606 1.8890 1.8370 .1250 .6250
RE7UI-03-24 1-1/2 .0020 - .0041 2.3634 2.9921 2.4630 .0950 2.3358 2.2410 2.1520 .1620 .7500
RE7UI-03-32 2 .0024 - .0051 2.9881 3.9921 3.2490 .1110 2.9606 2.8390 2.7750 .1890 1.0000
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. RE7UI-03-06 118 828
3/8 0.6250 0.6257 RE7UI-03-08 225 1575
1/2 0.8750 0.8758 RE7UI-03-10 338 2365
5/8 1.1250 1.1258 RE7UI-03-12 439 3077
3/4 1.2500 1.2510 RE7UI-03-16 811 5678
1 1.5625 1.5635 RE7UI-03-20 1184 8287
1-1/4 2.0000 2.0010 RE7UI-03-24 1622 11358
1-1/2 2.3750 2.3760 RE7UI-03-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
B d2
B1 d1 Order key
R J U I - 01 - 12 - ESR
s
iglide® Material
Stainless steel
303 Stainless steel adapter (1.4305)
Dimensionally interchangeable with linear ball bearings
Diameter
Standard
Closed
Equipped with liner made of iglide® J
Liner
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
JUI-01 (standard)
T500 liner optional for chemicals/high temps
(up to 482°F for steel housing) iglide® material options:
iglide® J: All around material
Suitable shafting for iglide® J: DryLin® AWI aluminum,
iglide® J200: Best for aluminum shafts
case-hardened, 300 series stainless Best shafting for
iglide® E7: Best for steel/stainless steel shafts
T500: hard-chrome and hard-stainless steel
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
RJUI-01-08ESR 1/2 .0016 - .0032 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
RJUI-01-10ESR 5/8 .0016 - .0032 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
RJUI-01-12ESR 3/4 .0016 - .0032 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
RJUI-01-16ESR 1 .0016 - .0032 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
RJUI-01-20ESR 1-1/4 .0020 - .0041 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
RJUI-01-24ESR 1-1/2 .0020 - .0041 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
Housing Bore
Recommendations Load Data
Nominal Part No. F max, dynamic F max, static
ID Size Min. Max. p = 725 psi (lbs) p = 5075 psi (lbs)
RJUI-01-08ESR 225 1575
1/2 0.8750 0.8758
5/8 1.1250 1.1258 DryLin® RJUI-01-10ESR 338 2365
Also available with liners: According to igus® testing method ➤ Page 1096
78)
B d2
B1 d1 Order key
R J U I - 03 - 12 - ESR
s
iglide® Material
Stainless steel
Self-aligning
303 Stainless steel adapter (1.4305)
Dimensionally interchangeable with linear ball bearings
Diameter
Closed
Equipped with liner made of iglide® J
Liner
Inch
Temperature range -40°F to +194°F (-40°C to +90°C)
JUI-01 (standard)
T500 liner optional for chemicals/high temps
iglide® material options:
(up to 482°F for steel housing) iglide® J: All around material
Suitable shafting for iglide® J: DryLin® AWI aluminum, iglide® J200: Best for aluminum shafts
case-hardened, 300 series stainless Best shafting for iglide® E7: Best for steel/stainless steel shafts
T500: hard-chrome and hard-stainless steel iglide® T500 (X)*: For high temps up to 356°F (180°C) in
aluminum adapter, up to 482°F (250°C) in steel housing
Dimensions (inch)
Part No. Nominal Tolerance** d2 B B1 s ds dn do o e
Size ISO h8 ISO h10 ISO H10 ISO h10 -0.004
RJUI-03-08ESR 1/2 .0016 - .0032 .8673 1.2461 .9870 .0520 .8556 .8200 .7120 .1250 .2815
RJUI-03-10ESR 5/8 .0016 - .0032 1.1173 1.4961 1.1360 .0620 1.1055 1.0600 .9620 .1250 .3125
RJUI-03-12ESR 3/4 .0016 - .0032 1.2421 1.6173 1.1980 .0620 1.2300 1.1770 1.0870 .1250 .3125
RJUI-03-16ESR 1 .0016 - .0032 1.5547 2.2421 1.7890 .0740 1.5271 1.4710 1.3990 .1250 .5000
RJUI-03-20ESR 1-1/4 .0020 - .0041 1.9881 2.6173 2.0390 .0740 1.9606 1.8890 1.8370 .1250 .6250
RJUI-03-24ESR 1-1/2 .0020 - .0041 2.3634 2.9921 2.4630 .0950 2.3358 2.2410 2.1520 .1620 .7500
Housing Bore
Load Data
Recommendations
DryLin® Part No. F max, dynamic F max, static
Nominal
STAINLESS p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max.
STEEL RJUI-03-08ESR 225 1575
1/2 0.8750 0.8758
RJUI-03-10ESR 338 2365
5/8 1.1250 1.1258
RJUI-03-12ESR 439 3077
3/4 1.2500 1.2510
RJUI-03-16ESR 811 5678
1 1.5625 1.5635
RJUI-03-20ESR 1184 8287
1-1/4 2.0000 2.0010
RJUI-03-24ESR 1622 11358
1-1/2 2.3750 2.3760
Also available with liners: According to igus® testing method ➤ Page 1096
78)
Order key
Type Size
T J U I - 01-10
iglide® Material
Anodized aluminum adapter
Standard
Diameter
Dimensionally interchangeable with linear ball bearings
Equipped with liner made of iglide® J
Liner
Split
Inch
Temperature range -40°F to +194°F, JUI-01 (standard)
T500 liner optional for chemicals/high temps
(356°F for aluminum)
iglide® material options:
Suitable shafting for iglide® J: DryLin® AWI aluminum,
iglide® J: All around material
case-hardened, 300 series stainless
iglide® J200: Best for aluminum shafts
Best shafting for T500: hard-chrome and hard-stainless steel iglide® E7: Best for steel/stainless steel shafts
iglide® T500 (X)*: For high temps up to 356°F (180°C)
in aluminum adapter
Dimensions (inch)
Part No. Nominal Tolerance(78) d2 B B1 s dn e o do
Size ISO h7 ISO h10 ISO H10 +.004
TJUI-01-08 1/2 .0016 - .0036 .8750 1.2500 .979 .0520 .8200 .281 .1250 .7120
TJUI-01-10 5/8 .0016 - .0036 1.1250 1.5000 1.124 .0620 1.0600 .312 .1250 .9620
TJUI-01-12 3/4 .0016 - .0036 1.2500 1.6200 1.186 .0620 1.1770 .312 .1250 1.0870
TJUI-01-16 1 .0016 - .0036 1.5625 2.2500 1.773 .0740 1.4710 .500 .1250 1.3990
TJUI-01-20 1-1/4 .0020 - .0039 2.0000 2.6200 2.023 .0740 1.8890 .625 .1250 1.8370
TJUI-01-24 1-1/2 .0020 - .0047 2.3750 3.0000 2.440 .0950 2.2410 .750 .1620 2.1520
TJUI-01-32 2 .0024 - .0057 3.0000 4.0000 3.222 .1110 2.8390 1.000 .1890 2.7750
Housing Bore
Load Data
Recommendations
Part No. F max, dynamic F max, static
Nominal p = 725 psi (lbs) p = 5075 psi (lbs)
ID Size Min. Max. TJUI-01-08 225 1575
1/2 0.8750 0.8758 TJUI-01-10 338 2365
5/8 1.1250 1.1258 TJUI-01-12 439 3077
3/4 1.2500 1.2510 TJUI-01-16 811 5678
1 1.5625 1.5635 TJUI-01-20 1184 8287
1-1/4 2.0000 2.0010 TJUI-01-24 1622 11358
1-1/2 2.3750 2.3760 TJUI-01-32 2885 20198
2 3.0000 3.0010
Also available with liners: According to igus® testing method ➤ Page 1096
78)
Order key
Type Size
T J U I - 21-10
iglide® Material
Low clearance
Anodized aluminum adapter
Diameter
Dimensionally interchangeable with linear ball bearings
Equipped with liner made of iglide® J
Liner
Split
Inch
Temperature range -40°F to +194°F
JUI-01 (standard)
T500 liner optional for chemicals/high temps iglide® material options:
(356°F for aluminum) iglide® J: All around material
Suitable shafting for iglide® J: DryLin® AWI aluminum, iglide® J200: Best for aluminum shafts
case-hardened, 300 series stainless iglide® E7: Best for steel/stainless steel shafts
Best shafting for T500: hard-chrome and hard-stainless iglide® T500 (X)*: For high temps up to 356°F (180°C)
steel in aluminum adapter
Dimensions (inch)
Part No. Nominal Tol