Professional Documents
Culture Documents
REPORT ON
For :
M/S. OM CONSTRUCTIONS,
KOTA
By :
PNT DESIGNS PVT LTD.
A-229 (A), Road No.5, I.P.I.A., Jhalawar Road
KOTA-324005 (Raj.)
Mob.09929866699, 9414188818
ISO 9001:2008 Quality Certified Lab.
PNT
The safe load carrying pressure of Socketed Pile (Socket Length 1.0m, Cut off 4.0m)
in rock for the foundation of Multistorey Building at Devashish City, Borkhera,
Kota (Raj.) is recommended as follows:
Safe Load Lateral Load
Dia of pile, Length of Pile
Location Carrying Capacity
d (meter) (meter)
Capacity Qs (ton) (ton)
CONTENTS
REFERENCES 12
APPENDIX-A
APPENDIX-B1-B5
APPENDIX-C1-C5
TABLES
SITE PLAN
1.0 INTRODUCTION
It is proposed to carry out Geotechnical Investigations for the
construction of Multistorey Building at Devashish City, Borkhera, Kota as
shown in Fig.1.
1
ISO 9001:2008 Quality Certified Lab.
PNT
2
ISO 9001:2008 Quality Certified Lab.
PNT
3
ISO 9001:2008 Quality Certified Lab.
PNT
(CL) mixed with Sand upto the depth of 14.70m. Beyond this, Medium
Grained Hard Rock was found upto the depth of exploration i.e. 19.50m.
The core recovery and RQD values are shown in bore-log i.e. Table-2.
BH-3: The upper layer of strata at the site consists of Low Plastic Clay
(CL) mixed with Sand upto the depth of 14.70m. Beyond this, Moderately
Weathered Hard Rock was found upto the depth of exploration i.e. 19.00m.
The core recovery and RQD values are shown in bore-log i.e. Table-3.
BH-4: The upper layer of strata at the site consists of Low Plastic Clay
(CL) mixed with Sand upto the depth of 13.50m. Below this, Highly
Weathered Rock was found upto the depth of 18.00m. Beyond this,
Medium Grained Hard Rock was found upto the depth of exploration i.e.
20.00m. The core recovery and RQD values are shown in bore-log i.e.
Table-4.
BH-5: The upper layer of strata at the site consists of Low Plastic Clay
(CL) mixed with Sand upto the depth of 14.00m. Below this, Highly
Weathered Rock was found upto the depth of 15.00m. Beyond this,
Medium Grained Hard Rock was found upto the depth of exploration i.e.
19.00m. The core recovery and RQD values are shown in bore-log i.e.
Table-5.
4
ISO 9001:2008 Quality Certified Lab.
PNT
5
ISO 9001:2008 Quality Certified Lab.
PNT
6.1.2 Rock Mass Rating (RMR) – may also be used to give net allowable
pressure as per Table-B. This will ensure settlement of raft
foundation up to 6 m thickness to be less than 12mm.
TABLE B NET SAFE BEARING PRESSURE BASED ON RMR
CLASSIFICATIO I II III IV V
N NO.
Description of rock Very Good Good Fair Poor Very
Poor
RMR 100-81 80-61 60-41 40-21 20-0
Qns (t/m²) 600-448 440-288 280-151 145-90-58 55-45-40
6
ISO 9001:2008 Quality Certified Lab.
PNT
7
ISO 9001:2008 Quality Certified Lab.
PNT
8
ISO 9001:2008 Quality Certified Lab.
PNT
9
ISO 9001:2008 Quality Certified Lab.
PNT
3. The results of free swell tests reveal that the soil at the site is found to be
Low expansive in nature.
4. The ground water table was observed at the depth of 2.50m at the time of
investigation (i.e. Jul’2017).
5. Raft foundation : The net allowable bearing capacity for Raft Foundation
has been recommended as :
Location Depth of Size of Net Allowable Type of
Foundation Foundation Bearing Capacity foundation
Df (m) (m) (t/m²)
BH-1 to Raft
BH-5
4.0m 17 X 43 10.0 t/m²
Foundation
10
ISO 9001:2008 Quality Certified Lab.
PNT
All the above recommendations are based upon the field data
collected from limited test locations and results of laboratory test carried
out on soil samples recovered from test bore holes and our experience in
this regard. In case the proposed structure is located away from the test
locations and /or the actual subsoil conditions during excavation of
foundation trench are found different from what has been reported above,
the consultants are to be referred for suggestions prior to taking up of actual
construction work at site.
DIRECTOR
11
ISO 9001:2008 Quality Certified Lab.
PNT
REFERENCES
1. IS: 1904-1978 Code of practice for design and construction of
(RA-2015) foundation on soil- General Requirement.
2. IS: 6403-1981 Code of practice for determination of bearing
(RA-2011) capacity of shallow foundations.
3. IS: 8009 Code of practice for calculation of settlement
Part I 1976 of foundations.
(RA-2013)
4. IS: 1498-1970 Classification & Identification of soil for general
(RA-2011) engineering purpose.
5. IS: 2131-1981 Method of standard penetration test for soil
(RA-2011)
6. IS: 4968 Method of subsurface soundings of soils
Part I 1976
(RA-2011)
7. Ranjan & Rao Basic and Applied Soil Mechanics :
(1992) Wiley Eastern Limited, Delhi
8. IS:13063:1991 Structural safety of building on shallow
(RA-2016) foundations on rocks- code of Practice
9. IS:12070-1987 Code of practice for design and construction
(RA-2015) of shallow foundation on rocks
10. IS:9143-1979 Method for the determination of unconfined
(RA-2016) compressive strength of rock materials
11. 11315 Part-11 Methods for the quantitative description
1985 of discontinuities in rock mass - Core recovery
(RA-2016) and rock quality designation.
12. IS:2720 Methods of determination of Engineering
Properties of soil.
13. IS: 1892-1979 Code of practice for Subsurface Investigation for Fdn.
14. IS: 2132-1986 Code of Practice For Thin-walled Tube Sampling
(RA-2011) of Soils
15. IS: 9179-1979 Method for the Preparation of Rock Specimen for
(RA-2016) Laboratory Testing
16. IS: 13030-1991 Method of Test For Laboratory Determination Of
(RA-2016) Water Content, Porosity, Density and Related
Properties of Rock Material
12
ISO 9001:2008 Quality Certified Lab.
PNT
Appendix-A
Shape factor
sc = 1.08 (For Raft Foundation)
Bearing Capacity factor
Nc = 5.14
Nq = 1
Nγ = 0
Depth factors
dc = 1 + 0.2 (Df/B) √NØ
dc = 1
(Depth factors has been considered 1.0 because the proper compaction of back filling at the
site can not be ensured.)
Pg.1
Inclination factors.
Ic = 1
Other Data Used
(Assuming fully submerged
γ' = 1.0 t/m3 condition)
Df = 4
F.O.S. = 2.5
The net ultimate bearing capacity is obtained from equation (1) and given as follows :
qnu = 7.5 X 5.14 X 1.08
= 41.63 t/m²
Therefore,
qnu 41.63
qns = --------- = -----------
FOS 2.5
= 16.65 t/m²
The value of net safe bearing capacity (for depth of the foundation = 4m.) obtained from
above equation has been obtained as 16.65t/m².
Input Data
Width, B = 17 = 17
Lenth, L = 43 = 43
Area, A = BX L = 731
Depth, Df = = 4
Ho = 2 XB = 34
Base Width, B' = B + (Ho /2) = 34
Base Length, L' L + (Ho /2) = 60
Pg.2
sf = s X df X rf = 122.83 mm
The allowable bearing pressure at the depth of Df=4m has been recommended as
10.0t/m² for the design of raft foundation. .
Pg.3
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE CONSTRUCTION OF MULTISTOREY
BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
BH-1
The analysis of bearing capacity has been carried out for rocky strata available at the site. Highly Weathered Rocky strata has been observed
at the depth of 16.00m. However, for highly weathered rock the safe load carrying capacity has been calculated as under. Therefore, length
of pile may be kept as depth upto rock level + socket length.
Load Carrying Capacity of Pile
A pile socketed into rock derives its capacity from end bearing and socket side resistance. The ultimate load carrying capacity may be
calculated from as per IRC:78-2014
Length of socket
df = Depth factor 1 0.4 x
Dia of socket
PNT
= 6 for socket resistance
Pg.1
The unconfined compressive strength of the rocky strata have been determined in the laboratory. The minimum strength of 35(P) i.e. 35X24=
2808 t/m² has been taken for calculation of bearing capacity of the proposed piles.
Other Data
Average (CR+RQD)/2 = 1/4 (56.0+0.0+45.33+0.0) = 25.3325 %
Ksp = 0.24 qc (t/m2)=
df = 1.2
qc = 28.08 N/mm²
Cus = 1.19 N/mm²
Maximum
Allowable end Allowable end Allowable side Allowable Load
Socket Base area, Surface Area, Allowable End Recommended Safe
Dia of pile, bearing bearing socket shear Carrying Capacity
Length, Ab = (π / 4)d² As = π . d . l Bearing Load Carrying
d (mm) Component Component Component Qa = Re /3 + Raf /6
l (mm) (mm2) (mm2) Component Capacity Qs (t)
/ 3 (N/mm2) (Re / 3) (N) (Raf / 6) (N) (N)
(Mpa)
600.00 1000.00 282857.14 1320000.00 2.70 5.00 762458.30 262303.30 1024761.60 100.00
ISO 9001:2008 Quality Certified Lab.
1000.00 1000.00 785714.29 2200000.00 2.70 5.00 2117939.73 437172.16 2555111.89 250.00
The load carrying capacity of the piles of other dimensions can be determined using above equation.
PNT
Pg.2
Appendix-B2
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE CONSTRUCTION OF MULTISTOREY
BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
BH-2
The analysis of bearing capacity has been carried out for rocky strata available at the site. Rocky strata has been observed at the depth of 14.70m.
Therefore, length of pile may be kept as depth upto rock level + socket length.
Length of socket
df = Depth factor 1 0.4 x
Dia of socket
PNT
= 6 for socket resistance
Pg.1
The unconfined compressive strength of the rocky strata have been determined in the laboratory. The minimum strength of 3472 t/m² has been
taken for calculation of bearing capacity of the proposed piles.
Other Data
Average (CR+RQD)/2 = 1/4 (58.89+32.22+58+42.67) = 47.945 %
Ksp = 0.53 qc (t/m2)=
df = 1.2
qc = 34.72 N/mm²
Cus = 1.33 N/mm²
Maximum
Allowable end Allowable end Allowable side Allowable Load Recommended
Socket Base area, Surface Area, Allowable End
Dia of pile, bearing bearing socket shear Carrying Capacity Safe Load
Length, Ab = (π / 4)d² As = π . d . l Bearing
d (mm) Component Component Component Qa = Re /3 + Raf /6 Carrying
l (mm) (mm2) (mm2) Component
/ 3 (N/mm2) (Re / 3) (N) (Raf / 6) (N) (N) Capacity Qs (t)
(Mpa)
600.00 1000.00 282857.14 1320000.00 7.37 5.00 1414285.71 291672.21 1705957.93 150.00
ISO 9001:2008 Quality Certified Lab.
1000.00 1000.00 785714.29 2200000.00 7.37 5.00 3928571.43 486120.36 4414691.78 350.00
The load carrying capacity of the piles of other dimensions can be determined using above equation.
PNT
Pg.2
Appendix-B3
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE CONSTRUCTION OF MULTISTOREY
BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
BH-3
The analysis of bearing capacity has been carried out for rocky strata available at the site. Rocky strata has been observed at the depth of 14.70m.
Therefore, length of pile may be kept as depth upto rock level + socket length.
Length of socket
df = Depth factor 1 0.4 x
Dia of socket
PNT
= 6 for socket resistance
Pg.1
The unconfined compressive strength of the rocky strata have been determined in the laboratory. The minimum strength of 3575 t/m² has been
taken for calculation of bearing capacity of the proposed piles.
Other Data
Average (CR+RQD)/2 = 1/4 (49.44+16.67+48.67 +0.0) = 28.695 %
Ksp = 0.28 qc (t/m2)=
df = 1.2
qc = 35.75 N/mm²
Cus = 1.35 N/mm²
Maximum
Allowable end Allowable end Allowable side Allowable Load Recommended
Socket Base area, Surface Area, Allowable End
Dia of pile, bearing bearing socket shear Carrying Capacity Safe Load
Length, Ab = (π / 4)d² As = π . d . l Bearing
d (mm) Component Component Component Qa = Re /3 + Raf /6 Carrying
l (mm) (mm2) (mm2) Component
/ 3 (N/mm2) (Re / 3) (N) (Raf / 6) (N) (N) Capacity Qs (t)
(Mpa)
600.00 1000.00 282857.14 1320000.00 4.05 5.00 1145590.22 295966.95 1441557.17 140.00
ISO 9001:2008 Quality Certified Lab.
1000.00 1000.00 785714.29 2200000.00 4.05 5.00 3182195.05 493278.26 3675473.31 350.00
The load carrying capacity of the piles of other dimensions can be determined using above equation.
PNT
Pg.2
Appendix-B4
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE CONSTRUCTION OF MULTISTOREY
BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
BH-4
The analysis of bearing capacity has been carried out for rocky strata available at the site. Rocky strata has been observed at the depth of 18.00m.
Therefore, length of pile may be kept as depth upto rock level + socket length.
Length of socket
df = Depth factor 1 0.4 x
Dia of socket
PNT
= 6 for socket resistance
Pg.1
The unconfined compressive strength of the rocky strata have been determined in the laboratory. The minimum strength of 3924 t/m² has been
taken for calculation of bearing capacity of the proposed piles.
Other Data
Average (CR+RQD)/2 = 1/2 (72.50+43.0) = 57.75 %
Ksp = 0.66 qc (t/m2)=
df = 1.2
qc = 39.24 N/mm²
Cus = 1.41 N/mm²
Maximum
Allowable end Allowable end Allowable side Allowable Load Recommended
Socket Base area, Surface Area, Allowable End
Dia of pile, bearing bearing socket shear Carrying Capacity Safe Load
Length, Ab = (π / 4)d² As = π . d . l Bearing
d (mm) Component Component Component Qa = Re /3 + Raf /6 Carrying
l (mm) (mm2) (mm2) Component
/ 3 (N/mm2) (Re / 3) (N) (Raf / 6) (N) (N) Capacity Qs (t)
(Mpa)
600.00 1000.00 282857.14 1320000.00 10.31 5.00 1414285.71 310077.10 1724362.82 150.00
ISO 9001:2008 Quality Certified Lab.
1000.00 1000.00 785714.29 2200000.00 10.31 5.00 3928571.43 516795.17 4445366.60 350.00
The load carrying capacity of the piles of other dimensions can be determined using above equation.
PNT
Pg.2
Appendix-B5
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE CONSTRUCTION OF MULTISTOREY
BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
BH-5
The analysis of bearing capacity has been carried out for rocky strata available at the site. Rocky strata has been observed at the depth of 15.00m.
Therefore, length of pile may be kept as depth upto rock level + socket length.
Length of socket
df = Depth factor 1 0.4 x
Dia of socket
PNT
= 6 for socket resistance
Pg.1
The unconfined compressive strength of the rocky strata have been determined in the laboratory. The minimum strength of 3492 t/m² has been
taken for calculation of bearing capacity of the proposed piles.
Other Data
Average (CR+RQD)/2 = 1/4 (57.0+39.0+65.0+40.0) = 50.25 %
Ksp = 0.56 qc (t/m2)=
df = 1.2
qc = 34.92 N/mm²
Cus = 1.33 N/mm²
Maximum
Allowable end Allowable end Allowable side Allowable Load Recommended
Socket Base area, Surface Area, Allowable End
Dia of pile, bearing bearing socket shear Carrying Capacity Safe Load
Length, Ab = (π / 4)d² As = π . d . l Bearing
d (mm) Component Component Component Qa = Re /3 + Raf /6 Carrying
l (mm) (mm2) (mm2) Component
/ 3 (N/mm2) (Re / 3) (N) (Raf / 6) (N) (N) Capacity Qs (t)
(Mpa)
600.00 1000.00 282857.14 1320000.00 7.83 5.00 1414285.71 292511.08 1706796.79 150.00
ISO 9001:2008 Quality Certified Lab.
1000.00 1000.00 785714.29 2200000.00 7.83 5.00 3928571.43 487518.46 4416089.89 350.00
The load carrying capacity of the piles of other dimensions can be determined using above equation.
PNT
Pg.2
PNT
Appendix-C1
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE
CONSTRUCTION OF MULTISTOREY BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
Ls = Length of socket
H = Horizontal load at top of socket
M = Moment at top of socket
D = Diameter of pile
σ1 = Permissible compressive strength of rock
= 0.33 x qc, qc in kg/cm2
or < 30 kg/cm2
Scour Depth = 0m
Cut-Off Level = 4m
Diameter of pile d = 0.6 m
Horizontal load at top of socket H = 40 kn
Length of pile above top of socket L1 = 12 m
Moment at top of socket M = 240 Kn-m
2
Unconfined Compressive strength of rock Qc = 280.80 kg/cm =2808 t/m²
2
Permissible compressive strength of rock σ1 = 30 kg/cm
2
(Lesser of 3 Mpa or 0.33*Qc) 3000 Kn/m
Min. Socket length in rock Ls = 0.940 m
Length of socket provided Ls = 1.000 m
1. The recommended lateral load carrying capacity is 4.0 tonnes for dia of 0.600m, socket 1.0m
2. The recommended lateral load carrying capacity is 7.0 tonnes for for dia of 1.0m, socket 1.0m
Appendix-C2
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE
CONSTRUCTION OF MULTISTOREY BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
Ls = Length of socket
H = Horizontal load at top of socket
M = Moment at top of socket
D = Diameter of pile
σ1 = Permissible compressive strength of rock
= 0.33 x qc, qc in kg/cm2
or < 30 kg/cm2
Scour Depth = 0m
Cut-Off Level = 4m
Diameter of pile d = 0.6 m
Horizontal load at top of socket H = 45 kn
Length of pile above top of socket L1 = 10.7 m
Moment at top of socket M = 240.75 Kn-m
2
Unconfined Compressive strength of rock Qc = 347.20 kg/cm =3472 t/m²
2
Permissible compressive strength of rock σ1 = 30 kg/cm
2
(Lesser of 3 Mpa or 0.33*Qc) 3000 Kn/m
Min. Socket length in rock Ls = 0.947 m
Length of socket provided Ls = 1.000 m
1. The recommended lateral load carrying capacity is 4.5 tonnes for dia of 0.600m, socket 1.0m
2. The recommended lateral load carrying capacity is 8.0 tonnes for for dia of 1.0m, socket 1.0m
Appendix-C3
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE
CONSTRUCTION OF MULTISTOREY BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
Ls = Length of socket
H = Horizontal load at top of socket
M = Moment at top of socket
D = Diameter of pile
σ1 = Permissible compressive strength of rock
= 0.33 x qc, qc in kg/cm2
or < 30 kg/cm2
Scour Depth = 0m
Cut-Off Level = 4m
Diameter of pile d = 0.6 m
Horizontal load at top of socket H = 45 kn
Length of pile above top of socket L1 = 10.7 m
Moment at top of socket M = 240.75 Kn-m
2
Unconfined Compressive strength of rock Qc = 357.50 kg/cm =3575 t/m²
2
Permissible compressive strength of rock σ1 = 30 kg/cm
2
(Lesser of 3 Mpa or 0.33*Qc) 3000 Kn/m
Min. Socket length in rock Ls = 0.947 m
Length of socket provided Ls = 1.000 m
1. The recommended lateral load carrying capacity is 4.5 tonnes for dia of 0.600m, socket 1.0m
2. The recommended lateral load carrying capacity is 8.0 tonnes for for dia of 1.0m, socket 1.0m
Appendix-C4
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE
CONSTRUCTION OF MULTISTOREY BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
Ls = Length of socket
H = Horizontal load at top of socket
M = Moment at top of socket
D = Diameter of pile
σ1 = Permissible compressive strength of rock
= 0.33 x qc, qc in kg/cm2
or < 30 kg/cm2
Scour Depth = 0m
Cut-Off Level = 4m
Diameter of pile d = 0.6 m
Horizontal load at top of socket H = 35 kn
Length of pile above top of socket L1 = 14 m
Moment at top of socket M = 245 Kn-m
2
Unconfined Compressive strength of rock Qc = 392.40 kg/cm =3924 t/m²
2
Permissible compressive strength of rock σ1 = 30 kg/cm
2
(Lesser of 3 Mpa or 0.33*Qc) 3000 Kn/m
Min. Socket length in rock Ls = 0.943 m
Length of socket provided Ls = 1.000 m
1. The recommended lateral load carrying capacity is 3.5 tonnes for dia of 0.600m, socket 1.0m
2. The recommended lateral load carrying capacity is 6.0 tonnes for for dia of 1.0m, socket 1.0m
Appendix-C5
CALCULATION OF ALLOWABLE BEARING CAPACITY OF PILE FOUNDATION FOR THE
CONSTRUCTION OF MULTISTOREY BUILDING AT DEVASHISH CITY, BORKHERA, KOTA
Ls = Length of socket
H = Horizontal load at top of socket
M = Moment at top of socket
D = Diameter of pile
σ1 = Permissible compressive strength of rock
= 0.33 x qc, qc in kg/cm2
or < 30 kg/cm2
Scour Depth = 0m
Cut-Off Level = 4m
Diameter of pile d = 0.6 m
Horizontal load at top of socket H = 45 kn
Length of pile above top of socket L1 = 11 m
Moment at top of socket M = 247.5 Kn-m
2
Unconfined Compressive strength of rock Qc = 349.20 kg/cm =3492 t/m²
2
Permissible compressive strength of rock σ1 = 30 kg/cm
2
(Lesser of 3 Mpa or 0.33*Qc) 3000 Kn/m
Min. Socket length in rock Ls = 0.960 m
Length of socket provided Ls = 1.000 m
1. The recommended lateral load carrying capacity is 4.5 tonnes for dia of 0.600m, socket 1.0m
2. The recommended lateral load carrying capacity is 8.0 tonnes for for dia of 1.0m, socket 1.0m
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
- 1.0
- 5 0.85 44.95 38.48 15.72 25.36 18.52 10.50 2.70 1.45 - - 13.33 -
- 2.0
- v
LO W
- 3.0 11 PLASTIC 3.80 7.25 58.71 30.24 34.81 21.05 15.50 2.68 1.60 - - 11.11 -
- CLAY (CL)
- 4.0 MIXED WITH
SAN D
- 11
- 5.0
-
- 6.0 23 8.40 10.75 26.68 54.17 31.92 23.53 15.90 2.69 1.80 7.50 0.0 12.50 0.11
ISO 9001:2008 Quality Certified Lab.
-
- 7.0
- R
- 8.0
-
- 9.0 45
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-1 Cont..
Table-1 Cont..
TABLE-1 : RESULT SHEET FOR BH-1
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
-10.0
- 29 LO W
-11.0 PLASTIC
CLAY (CL)
- MIXED WITH 4.75 60.50 27.11 7.64 22.48 NP 10.80 2.71 1.94 - - 0.0 -
-12.0 49 SAN D 9.65 24.85 57.64 7.86 29.32 19.30 - 2.70 1.90 12.50 0.0 12.50 0.10
-
-13.0
- 41
-14.0
-
-15.0 26
ISO 9001:2008 Quality Certified Lab.
PNT
Sp = Swelling Pressure
Table-1 Cont..
Table-1 Cont..
TABLE-1 : RESULT SHEET FOR BH-1
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
Bore Core RQD qu Density Return Water
Depth N- Description of
Log Recovery (%) (t/m²) (t/m3) Remark
(m) Values Strata
(%) Color Loss (%)
- 16.0
56.00 0.00 117(P) 2.42 Whitish 30
- HIGHLY
- 17.0 WEATHERED
R OC K 45.33 0.00 - - Whitish 30
-
- 18.0
-
- 19.0
-
- 20.0
-
- 21.0
-
- 22.0
-
- 23.0
ISO 9001:2008 Quality Certified Lab.
-
- 24.0
-
- 25.0
-
- 26.0
R = Refusal to SPT (N> 50), RQD = Rock Quality Designation, qu =Unixial Compressive Strength v = Water Table
PNT
TABLE-2 : RESULT SHEET FOR BH-2
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
- 1.0
- 20 2.05 26.95 62.48 8.52 30.15 21.21 - - - - - 14.26 -
- 2.0
- v
LO W
- 3.0 13 PLASTIC 3.30 12.20 71.83 12.68 31.41 21.70 - - - - - 15.12 -
- CLAY (CL)
- 4.0 MIXED WITH
SAN D
- 25 3.15 15.40 26.88 54.57 33.90 20.55 14.80 2.68 1.79 7.6 0.0 11.11 0.11
- 5.0
-
- 6.0 33 5.75 20.20 25.92 48.13 28.81 22.30 - - 1.91 - - 12.56 -
ISO 9001:2008 Quality Certified Lab.
-
- 7.0
- 26 15.20 16.90 27.84 40.06 29.79 14.62 - - - - - 13.33 -
- 8.0
-
- 9.0 34
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-2 Cont..
Table-2 Cont..
TABLE-2 : RESULT SHEET FOR BH-2
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
-10.0
- 28 LO W 23.50 22.20 35.84 18.46 32.75 10.89 - 2.70 1.85 11.50 0.0 5.56 0.10
-11.0 PLASTIC
CLAY (CL)
- MIXED WITH 4.75 60.50 27.11 7.64 22.48 NP 10.80 2.71 1.94 - - 0.0 -
-12.0 15 SAN D
-
-13.0
- 42
-14.0
--14.7
-15.0 Table Cont..
ISO 9001:2008 Quality Certified Lab.
-
-16.0
-
-17.0
-
-18.0
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-2 Cont..
Table-2 Cont..
TABLE-2 : RESULT SHEET FOR BH-2
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
Bore Core RQD qu Density Return Water
Depth N- Description of
Log Recovery (%) (t/m²) (t/m3) Remark
(m) Values Strata
(%) Color Loss (%)
--14.7
- 58.89 32.22 3472 2.42 Whitish 30
COARSE
- 16.0
GR AINED
- HARD
- 17.0 R OC K 58.00 42.67 - Whitish 25
-
- 18.0
- 67.00 34.00 3558 2.51 Whitish 30
- 19.0
-
- 20.0
-
- 21.0
-
ISO 9001:2008 Quality Certified Lab.
- 22.0
-
- 23.0
-
- 24.0
-
R = Refusal to SPT (N> 50), RQD = Rock Quality Designation, qu =Unixial Compressive Strength v = Water Table
PNT
TABLE-3 : RESULT SHEET FOR BH-3
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - AUG.’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
- 1.0
- 5
- 2.0
- v
LO W
- 3.0 8 PLASTIC 0.00 39.85 15.04 45.11 29.29 9.89 - - - - - 18.00 -
- CLAY (CL)
- 4.0 MIXED WITH
SAN D
- 10
- 5.0
-
- 6.0 12 15.25 23.60 55.04 6.12 23.57 15.96 - 2.69 1.69 7.30 0.0 16.67 0.12
ISO 9001:2008 Quality Certified Lab.
-
- 7.0
- 15
- 8.0 10.90 17.40 62.38 9.32 33.94 16.85 - - - - - 10.53 -
-
- 9.0 16
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-3 Cont..
Table-3 Cont..
TABLE-3 : RESULT SHEET FOR BH-3
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - AUG.’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
- 16
-
-10.0
- 50 LO W
-11.0 PLASTIC
CLAY (CL)
- MIXED WITH 4.75 60.50
12.30 22.25 27.11
58.25 7.64
7.20 22.48
32.25 15.20
NP 10.80
- 2.68
2.71 1.90
1.94 12.50
- 0.0
- 11.11
0.0 0.10
-
-12.0 18 SAN D
-
-13.0
- 34
-14.0
--14.7
-15.0 Table Cont..
ISO 9001:2008 Quality Certified Lab.
-
-16.0
-
-17.0
-
-18.0
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-3 Cont..
Table-3 Cont..
TABLE-3 : RESULT SHEET FOR BH-3
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - AUG.’2017
Bore Core RQD qu Density Return Water
Depth N- Description of
Log Recovery (%) (t/m²) (t/m3) Remark
(m) Values Strata
(%) Color Loss (%)
-14.7
-
- 49.44 16.67 3575 2.75 Whitish 30
- 16.0
- MODERATELY
- 17.0 WEATHERED
HARD ROCK 48.67 0.00 - - Whitish 40
-
- 18.0
- 77.00 11.00 3443 2.70 Whitish 40
- 19.0
-
- 20.0
-
- 21.0
-
ISO 9001:2008 Quality Certified Lab.
- 22.0
-
- 23.0
-
- 24.0
-
R = Refusal to SPT (N> 50), RQD = Rock Quality Designation, qu =Unixial Compressive Strength v = Water Table
PNT
TABLE-4 : RESULT SHEET FOR BH-4
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
- 1.0
- 15 7.00 21.20 23.69 48.11 29.98 19.29 - - - - - 15.56 -
- 2.0
- v
LO W
- 3.0 13 PLASTIC
- CLAY (CL)
- 4.0 MIXED WITH
SAN D
- 29 4.50 22.50 24.09 48.91 31.53 20.47 14.80 2.68 1.85 8.0 0.0 11.11 0.11
- 5.0
-
- 6.0 31
ISO 9001:2008 Quality Certified Lab.
-
- 7.0
- 38 0.75 34.75 20.64 43.86 34.65 22.68 - - - - - 11.11 -
- 8.0
-
- 9.0 38
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-4 Cont..
Table-4 Cont..
TABLE-4 : RESULT SHEET FOR BH-4
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
- 38
-
-10.0
- 47 LO W
-11.0 PLASTIC
CLAY (CL)
- MIXED WITH 4.75
8.10 60.50
34.95 27.11 36.45
20.50 7.64 22.48
21.90 20.41
NP 10.80
- 2.71
2.69 1.94
1.84 10.00
- 0.00
- 16.67
0.0 0.11
-
-12.0 26 SAN D
-
-13.0
- 29
-14.0
--14.7
-15.0 Table Cont..
ISO 9001:2008 Quality Certified Lab.
-
-16.0
-
-17.0
-
-18.0
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-4 Cont..
Table-4 Cont..
TABLE-4 : RESULT SHEET FOR BH-4
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
Bore Core RQD qu Density Return Water
Depth N- Description of
Log Recovery (%) (t/m²) (t/m3) Remark
(m) Values Strata
(%) Color Loss (%)
-
- 14.0
- 34.67 8.00 2208 2.35
- 15.0 HIGHLY
- WEATHERED
- 16.0 R OC K 35.33 0.00 106(P) 2.46 Yellowish 65
-
- 17.0
- 68.67 0.00
- 18.0
- COARSE
- 19.0 GR AINED 72.50 43.00 3924 2.49 Brownish 85
- HARD ROCK
- 20.0
-
ISO 9001:2008 Quality Certified Lab.
- 21.0
-
- 22.0
-
- 23.0
-
R = Refusal to SPT (N> 50), RQD = Rock Quality Designation, qu =Unixial Compressive Strength v = Water Table
PNT
TABLE-5 : RESULT SHEET FOR BH-5
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
-
-
- 1.0
- 16 5.75 37.50 16.46 40.29 28.65 16.80 - - - - - 15.36
- 2.0
-
LO W
- 3.0 25 PLASTIC
- CLAY (CL)
- 4.0 MIXED WITH
SAN D
- 29 6.00 15.00 51.35 27.65 33.11 18.87 15.50 2.70 1.83 8.0 0.0 11.11 0.11
- 5.0
-
- 6.0 34
ISO 9001:2008 Quality Certified Lab.
-
- 7.0
- 40 12.50 28.50 20.06 38.94 33.67 21.37 - - - - - 10.00 -
- 8.0
-
- 9.0 R
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-5 Cont..
Table-5 Cont..
TABLE-5 : RESULT SHEET FOR BH-5
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
IS Classification Sieve Size Analysis Atterberg Limits Natural Shear
Depth (m)
Bulk Density
N - value
Specific
Liquid Plastic
Gravity
content,% % cc
Gravel
Sand
Clay
(t/m3)
Limit c ø
Silt
Limit
%
Soil Descreption (Sr, %)
%
% % t/m2 deg.
- R
-
-10.0 22.25 16.50 20.83 40.43 33.43 19.13 - - 1.95 - - 12.52 -
- R LO W
-11.0 PLASTIC
CLAY (CL)
- MIXED WITH 4.75 60.50 27.11 7.64 22.48 NP 10.80 2.71 1.94 - - 0.0 -
-12.0 R SAN D 9.00 18.00 22.63 50.37 33.72 21.30 - - - - - 11.76
-
-13.0
- 29
-14.0
--14.7
-15.0 Table Cont..
ISO 9001:2008 Quality Certified Lab.
-
-16.0
-
-17.0
-
-18.0
* = Consolidation Test, cc = Compression Index, DFS = Differential Free Swell, v = Water Table
PNT
Sp = Swelling Pressure
Table-5 Cont..
Table-5 Cont..
TABLE-5 : RESULT SHEET FOR BH-5
PROJECT : GEOTECHNICAL INVESTIGATION FOR CONSTRUCTION OF MULTISTORY BUILDING
AT DEVASHISH CITY, BORKHERA, KOTA (RAJ.)
MONTH - JULY’2017
Bore Core RQD qu Density Return Water
Depth N- Description of
Log Recovery (%) (t/m²) (t/m3) Remark
(m) Values Strata
(%) Color Loss (%)
- 14.0
- HIGHLY WEATHERED 20.00 0.00 - -
ROCK
- 15.0
- 57.00 39.00 3492 2.54 Brownish 35
- 16.0
- COARSE 65.00 40.00 3981 2.57
- 17.0 GR AINED
- HARD 69.00 24.00 - - Brownish 30
- 18.0 R OC K
- 69.00 24.00 - -
- 19.0
-
- 20.0
-
- 21.0
ISO 9001:2008 Quality Certified Lab.
-
- 22.0
-
- 23.0
-
R = Refusal to SPT (N> 50), RQD = Rock Quality Designation, qu =Unixial Compressive Strength v = Water Table
PNT