Professional Documents
Culture Documents
At 16T/sqm SBC_WWT
Height of Tower M 40.00
Maximim Downward Force KN 789.97
Maximum Uplift KN 744.43
Side Thrust (T) KN 57.99
Side Thrust (L) KN 57.99
Gade of concrete M-30
Grade of steel Fe-500
Density of concrete KN/CUM 25.00
Leg to Leg distance tower M 4.00
ASSUMED DATA
Side of Lower Base M 3.90
Side of Upper Base M 1.50
Base of Pedestal M 0.75
Height of Foundation above
Ground Level M 0.50
Height of Foundation Below
Ground Level M 3.00
Thickness of Lower Slab M 0.45
Thickness of Upper Slab M 0.30
design
CHECK FOR SLIDING
Pressure due to Soil
p=wxhx(1+Sin PHI)/(1-Sin PHI) KN/SQM
At h= 2.25 118.37 KN/SQM
At h= 2.55 134.15 KN/SQM
At h= 3.00 157.83 KN/SQM
Force, F1 KN 99.88
F2 KN 56.82
F3 KN 256.22
Total Force KN 412.91
F.O.S. against Sliding 7.12 > 1.5HENCE OK
AS PER IS 456:2000 CLAUSE 20
CHECK FOR OVERTURNING
design
CHECK FOR PUNCHING SHEAR
CHECKING AT PEDESTAL
It is at a depth d/2 from the pedestal
Clear cover in Foundation Slab M 0.075
Assuming Effective Cover M 0.099
Effective Depth M 0.651
d/2 M 0.3255
Side of Punching Perimeter M 1.401
Punching Shear Force KN 1429.35
Factored Punching Shear/Face KN 536.01
Punching Shear Stess, tv N/SQMM 0.588
Permissible Shear Stress (CL. 30.6.3 of IS: 456-1978)
ks=0.5+Bc
Where Bc= Ratio of Short Side to
Long Side 1
ks= 1.5 > 1 Therefore consider ks=1
tc=0.25*SQRT(fck)*ks N/SQMM 1.12 > 0.588
HENCE SAFE
CHECKING AT END OF UPPER SLAB
It is at a depth d/2 from the pedestal
Effective Depth M 0.351
d/2 M 0.1755
Side of Punching Perimeter M 1.851
Punching Shear Force 1271.45
Factored Punching Shear/Face 476.80
Punching Shear Stess, tv 0.734
Permissible Shear Stress (CL. 30.6.3 of IS: 456-1978)
ks=0.5+Bc
Where Bc= Ratio of Short Side to
Long Side 1
ks= 1.5 > 1 Therefore consider ks=1
tc=0.25*SQRT(fck)*ks N/SQMM 1.12 > 0.734
HENCE OK
design
CALCULATION OF BOTTOM REINFORCEMENT OF PAD
CONSIDERING MOMENT ALONG PEDESTAL
Mu/bd2 N/SQMM 0.425
pt % 0.142 Refer Table- 2 of SP-16
Area of Steel Required SQMM/M 924.42
Check for Minimum Steel
0.12% of Gross Area SQMM/M 781.200 As per CL:25.5.1.1 of IS: 456-1978
Assume Dia of Bar MM 12
Spacing of Bars MM 122.28 Provide 90 MM C/C BOTHWAYS
ALONG PEDESTAL
Distance from edge M 2.325
Distance from other edge M 1.58
Pressure along Pedestal N/SQMM 43.781
ALONG EDGE OF UPPER SLAB
Distance from edge M 2.7
Distance from other edge M 1.20
Pressure along edge of Upper
Slab N/SQMM 51.734
Considering one metre width of Base Slab
Moment along Pedestal KNM 81.921
Factored Moment KNM 122.881
Moment along edge of Upper
Slab KNM 49.463
Factored Moment KNM 74.195
design
CALCULATION OF TOP REINFORCEMENT OF PAD
CONSIDERUNG MOMENT ALONG PEDESTAL
Mu/bd2 N/SQMM 0.290
pt % 0.143 Refer Table- 2 of SP-16
Area of Steel Required SQMM/M 930.93
Check for Minimum Steel
0.12% of Gross Area SQMM/M 781.200 As per CL:25.5.1.1 of IS: 456-1978
Assume Dia of Bar MM 12
Spacing of Bars MM 121.43 Provide 100 MM C/C BOTHWAYS
CONSIDERING MOMENT ALONG UPPER SLAB
Mu/bd2 N/SQMM 0.602
pt % 0.172 Refer Table- 2 of SP-16
Area of Steel Required SQMM/M 603.72
Check for Minimum Steel
0.12% of Gross Area SQMM/M 421.200 As per CL:25.5.1.1 of IS: 456-1978
Assume Dia of Bar MM 12
Spacing of Bars MM 187.24 Provide 150 MM C/C BOTHWAYS
design
DESIGN OF COLUMN/PEDESTAL
Side of Column M 0.75
Factored downward Load, Pu KN 1,184.96
Area of Pedestal SQMM 562500
Dia. of Bars MM 20
No. of Bars NO. 16
Effective of Cover MM 83
Effective of Depth MM 667
Area of Steel Provided SQMM 5024
% of Steel % 1.004
Pu/fck*b*d 0.118
d'/d 0.124
p/fck 0.0502
Reffering chart 49 of SP:16
Mu/fckbdd 0.08
HENCE Mux1 = Muy1
Mux1 KNM 675
Mux 173.97
Mux/Mux1 0.258 Hence safe
DESIGN OF COLUMN/PEDESTAL-TENSION BENDING CASE
Side of Column M 0.75
Factored downward Load, Pu KN 1,116.65
Area of Pedestal SQMM 562500
Dia. of Bars MM 20
No. of Bars NO. 16
Effective of Cover MM 83
Effective of Depth MM 667
Area of Steel Provided SQMM 5024
% of Steel % 1.004
Pu/fck*b*d 0.112
d'/d 0.12
p/fck 0.0502
Reffering chart 84 of SP:16
Mu/fckbdd 0.05
HENCE Mux1 = Muy1
Mux1 KNM 421.875
Mux 173.97
Mux/Mux1 0.412 Hence safe
design
L/D 8.888888889
Moment due to sinking
For differential settlement of 16 MM
delta MM 16
Moment = 6EsI delta/L2 N-MM 182250000
KN-M 182.25
Total Factored Moment KN-M 273.375
Mu/bdd 7.409
pt % 0.662
Ast MM2 814.26
Assume dia of Bar MM 20
Area of one bar MM2 314
No. of Bars No. 2.59
Provide 4 No.-20 MM Dia on top as well as on the bottom of the beam.
Shear reinforcement provided is 2 legged 8 MM Dia.@ 100MM C/C upto 1000MM from
each suppor & rest @ 200MM c/c
design