Professional Documents
Culture Documents
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4AD-ADP units made in June, 2005 or later comply with the EC Directive (EMC [10] 24+ This section describes the connection method to the PLC (FX3U Series PLC is
[5]
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4AD-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201) [2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
V2+
90(3.55")
98(3.86")
Regarding the standards that relate to the main unit, please refer to either the FX mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D13901 COM2 For the expansion board installation procedure, refer to the following manual:
Attention
Revision M V3+ → FX 3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. 3) Remove the special adapter connector cover
Date January 2017 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European COM3 When connecting this product to another
S
/E
R
8M
-48M
special adapter, please replace the 4)
-4
3U
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- V4+
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device 'expansion board' in the above description
I4+
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") 74(2.92") with a 'special adapter' and perform the N
15.1 COM4
RU
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care-
ST
conduit as high voltage cabling. Where possible users should run analog
Used to connect additional special adapters onto the left side of this special (fig.C) to the C FX
3U R/E
S
cables separately.
- 8M
-48M FX3U-4
*** -
***
3U
FX
adapter.
P
main unit as
O
W
E
Safety Precautions (Read these precautions before use.)
R
• Good cable shielding should be used. When terminating the shield at Earth 6)
[4] Special adapter connector cover: shown on the
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created.
Remove this cover to connect additional special adapters to the left side. right. RU
N
• When reading analog values, EMC accuracy can be improved out by 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw)
Not used when connecting to FX3GC/FX 3UC Series PLC. special adapter 5)
analog special adapters or through a users program. 6)
[6] POWER LED (green): slide lock (fig.B)
Indicates that incorrect handling may cause hazardous of the main unit
Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'.
conditions, resulting in death or severe injury. 1. Outline to fix the special 5)
The FX3U-4AD-ADP special adapter for analog input (hereinafter called 4AD-ADP) is a [7] Terminal block (European type):
adapter (fig.C).
Indicates that incorrect handling may cause hazardous Connect the analog voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury special adapter to add four analog input points.
[8] Special adapter connector:
or physical damage. 1.1 Incorporated Items Used to connect this special adapter to PLC main unit or special adapter. 5) B
Verify that the following product and items are included in the package: [9] DIN rail mounting hook
Connection precautions
Depending on the circumstances, procedures indicated by may [10] Special adapter fixing hook
Product FX3U-4AD-ADP analog input special adapter Connect all the high-speed I/O special adapters before connecting other
also cause severe injury. [11] Special adapter connector: special adapters when they are used in combination.
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4AD-ADP. special adapters other than other high-speed I/O special adapters.
Associated Manuals
2. Installation
Manual name Manual No. Description
For installation/uninstallation details, refer to the respective PLC User's manual
FX3S /FX3G/FX3GC/FX3U / Describes specifications for Hardware Edition.
JY997D16701 analog control and
FX3UC Series
MODEL CODE: programming method for INSTALLATION
User's Manual FX3S /FX3G/FX 3GC/FX 3U/
09R619 PRECAUTIONS
- Analog Control Edition FX3UC Series PLC.
• Make sure to cut off all phases of the power supply externally before attempting
FX3S /FX3G/FX3GC/FX3U /
installation or wiring work.
FX3UC Series JY997D16601 Describes PLC programming Failure to do so may cause electric shock or damage to the product.
Programming Manual MODEL CODE: for basic/applied instructions
- Basic & Applied 09R517 and devices.
Instruction Edition INSTALLATION
PRECAUTIONS
FX3S Series JY997D48601 E xplains FX 3S Series PLC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Use the product within the generic environment specifications described in PLC
- Hardware Edition 09R535 installation, and maintenance. main unit manual (Hardware Edition).
Never use the product in areas with excessive dust, oily smoke, conductive dusts,
FX3G Series JY997D31301 E xplains FX 3G Series P LC corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , or NO 2 ), flammable gas, vibration or
User’s Manual MODEL CODE: specifications for I/O, wiring, impacts, or expose it to high temperature, condensation, or rain and wind.
- Hardware Edition 09R521 installation, and maintenance. If the product is used in such conditions, electric shock, fire, malfunctions,
FX3GC Series JY997D45401 Explains FX 3GC Series PLC deterioration or damage may occur.
User’s Manual MODEL CODE: specifications for I/O, wiring, • When drilling screw holes or wiring, make sure cutting or wire debris does not
- Hardware Edition 09R533 installation, and maintenance. enter the ventilation slits.
Failure to do so may cause fire, equipment failures or malfunctions.
FX3U Series JY997D16501 E xplains FX 3U S eries P LC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Do not touch the conductive parts of the product directly.
- Hardware Edition 09R516 installation, and maintenance. Doing so may cause device failures or malfunctions.
• Connect special adapter securely to their designated connectors.
FX3UC Series JY997D28701 Explains FX 3UC Series PLC Loose connections may cause malfunctions.
User’s Manual MODEL CODE: specifications for I/O, wiring,
- Hardware Edition 09R519 installation, and maintenance.
<Reference>
Digital output
Input Exclusion of loss in opportunity and secondary loss from warranty liability
DISPOSAL characteristics
Manufacturer Model Caulking tool Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
PRECAUTIONS
(1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
CRIMPFOX 6*1 (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
Phoenix Contact Co., Ltd. AI 0.5-8WH • Please contact a certified electronic waste disposal company for the 0 4mA 20mA 20.4
(or CRIMPFOX 6T-F*2) 0 10V 10.2V
mA (3) Special damages and secondary damages whether foreseeable or not, compensation for
environmentally safe recycling and disposal of your device. Analog input Analog input
accidents, and compensation for damages to products other than Mitsubishi products.
*1 Old model name: CRIMPFOX ZA 3
TRANSPORTATION AND • The photocoupler is adopted to insulate the analog input area (4) Replacement by the user, maintenance of on-site equipment, start-up test run
*2 Old model name: CRIMPFOX UD 6 from the PLC. and other tasks.
STORAGE PRECAUTIONS Insulation
- Strand wire/single wire - Stick terminal with insulating sleeve • The DC/DC converter is adopted to insulate the power supply
• The product is a precision instrument. During transportation, avoid impacts larger method
Insulation sleeve Contact area
(Crimp area) than those specified in the general specifications by using dedicated packaging
line from the analog input area. For safe use
• Channels are not insulated from each other.
boxes and shock-absorbing palettes. Failure to do so may cause failures in the
Occupied 0 point (This number is not related to the maximum number of • This product has been manufactured as a general-purpose part for general
product. After transportation, verify operation of the product and check for damage
9mm 8mm points input/output points of the PLC.) industries, and has not been designed or manufactured to be incorporated in
of the mounting part, etc.
(0.35") (0.31") a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
2.6mm(0.1") 14mm(0.55") power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
When using a stick terminal with insulating sleeve, choose a wire with proper • This product has been manufactured under strict quality control. However
cable sheath referring to the above outside dimensions, or otherwise, the wire when installing the product where major accidents or losses could occur if the
cannot be inserted easily. product fails, install appropriate backup or failsafe functions in the system.
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal
screws with a torque outside the above-mentioned range. Failure to do so may
cause equipment failures or malfunctions.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
JY997D13901M Side
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4AD-ADP units made in June, 2005 or later comply with the EC Directive (EMC [10] 24+ This section describes the connection method to the PLC (FX3U Series PLC is
[5]
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4AD-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201) [2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
V2+
90(3.55")
98(3.86")
Regarding the standards that relate to the main unit, please refer to either the FX mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D13901 COM2 For the expansion board installation procedure, refer to the following manual:
Attention
Revision M V3+ → FX 3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. 3) Remove the special adapter connector cover
Date January 2017 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European COM3 When connecting this product to another
S
/E
R
8M
-48M
special adapter, please replace the 4)
-4
3U
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- V4+
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device 'expansion board' in the above description
I4+
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") 74(2.92") with a 'special adapter' and perform the N
15.1 COM4
RU
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care-
ST
conduit as high voltage cabling. Where possible users should run analog
Used to connect additional special adapters onto the left side of this special (fig.C) to the C FX
3U R/E
S
cables separately.
- 8M
-48M FX3U-4
*** -
***
3U
FX
adapter.
P
main unit as
O
W
E
Safety Precautions (Read these precautions before use.)
R
• Good cable shielding should be used. When terminating the shield at Earth 6)
[4] Special adapter connector cover: shown on the
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created.
Remove this cover to connect additional special adapters to the left side. right. RU
N
• When reading analog values, EMC accuracy can be improved out by 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw)
Not used when connecting to FX3GC/FX 3UC Series PLC. special adapter 5)
analog special adapters or through a users program. 6)
[6] POWER LED (green): slide lock (fig.B)
Indicates that incorrect handling may cause hazardous of the main unit
Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'.
conditions, resulting in death or severe injury. 1. Outline to fix the special 5)
The FX3U-4AD-ADP special adapter for analog input (hereinafter called 4AD-ADP) is a [7] Terminal block (European type):
adapter (fig.C).
Indicates that incorrect handling may cause hazardous Connect the analog voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury special adapter to add four analog input points.
[8] Special adapter connector:
or physical damage. 1.1 Incorporated Items Used to connect this special adapter to PLC main unit or special adapter. 5) B
Verify that the following product and items are included in the package: [9] DIN rail mounting hook
Connection precautions
Depending on the circumstances, procedures indicated by may [10] Special adapter fixing hook
Product FX3U-4AD-ADP analog input special adapter Connect all the high-speed I/O special adapters before connecting other
also cause severe injury. [11] Special adapter connector: special adapters when they are used in combination.
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4AD-ADP. special adapters other than other high-speed I/O special adapters.
Associated Manuals
2. Installation
Manual name Manual No. Description
For installation/uninstallation details, refer to the respective PLC User's manual
FX3S /FX3G/FX3GC/FX3U / Describes specifications for Hardware Edition.
JY997D16701 analog control and
FX3UC Series
MODEL CODE: programming method for INSTALLATION
User's Manual FX3S /FX3G/FX 3GC/FX 3U/
09R619 PRECAUTIONS
- Analog Control Edition FX3UC Series PLC.
• Make sure to cut off all phases of the power supply externally before attempting
FX3S /FX3G/FX3GC/FX3U /
installation or wiring work.
FX3UC Series JY997D16601 Describes PLC programming Failure to do so may cause electric shock or damage to the product.
Programming Manual MODEL CODE: for basic/applied instructions
- Basic & Applied 09R517 and devices.
Instruction Edition INSTALLATION
PRECAUTIONS
FX3S Series JY997D48601 E xplains FX 3S Series PLC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Use the product within the generic environment specifications described in PLC
- Hardware Edition 09R535 installation, and maintenance. main unit manual (Hardware Edition).
Never use the product in areas with excessive dust, oily smoke, conductive dusts,
FX3G Series JY997D31301 E xplains FX 3G Series P LC corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , or NO 2 ), flammable gas, vibration or
User’s Manual MODEL CODE: specifications for I/O, wiring, impacts, or expose it to high temperature, condensation, or rain and wind.
- Hardware Edition 09R521 installation, and maintenance. If the product is used in such conditions, electric shock, fire, malfunctions,
FX3GC Series JY997D45401 Explains FX 3GC Series PLC deterioration or damage may occur.
User’s Manual MODEL CODE: specifications for I/O, wiring, • When drilling screw holes or wiring, make sure cutting or wire debris does not
- Hardware Edition 09R533 installation, and maintenance. enter the ventilation slits.
Failure to do so may cause fire, equipment failures or malfunctions.
FX3U Series JY997D16501 E xplains FX 3U S eries P LC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Do not touch the conductive parts of the product directly.
- Hardware Edition 09R516 installation, and maintenance. Doing so may cause device failures or malfunctions.
• Connect special adapter securely to their designated connectors.
FX3UC Series JY997D28701 Explains FX 3UC Series PLC Loose connections may cause malfunctions.
User’s Manual MODEL CODE: specifications for I/O, wiring,
- Hardware Edition 09R519 installation, and maintenance.
<Reference>
Digital output
Input Exclusion of loss in opportunity and secondary loss from warranty liability
DISPOSAL characteristics
Manufacturer Model Caulking tool Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
PRECAUTIONS
(1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
CRIMPFOX 6*1 (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
Phoenix Contact Co., Ltd. AI 0.5-8WH • Please contact a certified electronic waste disposal company for the 0 4mA 20mA 20.4
(or CRIMPFOX 6T-F*2) 0 10V 10.2V
mA (3) Special damages and secondary damages whether foreseeable or not, compensation for
environmentally safe recycling and disposal of your device. Analog input Analog input
accidents, and compensation for damages to products other than Mitsubishi products.
*1 Old model name: CRIMPFOX ZA 3
TRANSPORTATION AND • The photocoupler is adopted to insulate the analog input area (4) Replacement by the user, maintenance of on-site equipment, start-up test run
*2 Old model name: CRIMPFOX UD 6 from the PLC. and other tasks.
STORAGE PRECAUTIONS Insulation
- Strand wire/single wire - Stick terminal with insulating sleeve • The DC/DC converter is adopted to insulate the power supply
• The product is a precision instrument. During transportation, avoid impacts larger method
Insulation sleeve Contact area
(Crimp area) than those specified in the general specifications by using dedicated packaging
line from the analog input area. For safe use
• Channels are not insulated from each other.
boxes and shock-absorbing palettes. Failure to do so may cause failures in the
Occupied 0 point (This number is not related to the maximum number of • This product has been manufactured as a general-purpose part for general
product. After transportation, verify operation of the product and check for damage
9mm 8mm points input/output points of the PLC.) industries, and has not been designed or manufactured to be incorporated in
of the mounting part, etc.
(0.35") (0.31") a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
2.6mm(0.1") 14mm(0.55") power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
When using a stick terminal with insulating sleeve, choose a wire with proper • This product has been manufactured under strict quality control. However
cable sheath referring to the above outside dimensions, or otherwise, the wire when installing the product where major accidents or losses could occur if the
cannot be inserted easily. product fails, install appropriate backup or failsafe functions in the system.
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal
screws with a torque outside the above-mentioned range. Failure to do so may
cause equipment failures or malfunctions.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
JY997D13901M Side
B
Side
A JAPANESE
Side
B ENGLISH
Applicable standards 1.2 External Dimensions, Part Names, and Terminal Layout 2.1 Connection to the PLC
FX3U-4AD-ADP units made in June, 2005 or later comply with the EC Directive (EMC [10] 24+ This section describes the connection method to the PLC (FX3U Series PLC is
[5]
Directive) and UL standards (UL, cUL). Further information can be found in the [3] [4] used for the following example).
following manual. 24- For installation method to other PLCs, refer to the respective PLC User's manual
[6]
→ FX3S Series Hardware Manual (Manual No. JY997D48301) Hardware Edition.
FX3U-4AD-ADP → FX3G Series Hardware Manual (Manual No. JY997D46001)
→ FX3GC Series Hardware Manual (Manual No. JY997D45201) [2] [7] V1+ Procedure
1) Turn off the power.
→ FX3U Series Hardware Manual (Manual No. JY997D50301) I1+
106(4.18")
V2+
90(3.55")
98(3.86")
Regarding the standards that relate to the main unit, please refer to either the FX mounted directly using screws.
[1]
series product catalog or consult with your nearest Mitsubishi product provider. I2+ 2) Install an expansion board to the main unit.
Manual Number JY997D13901 COM2 For the expansion board installation procedure, refer to the following manual:
Attention
Revision M V3+ → FX 3U Series User's Manual - Hardware Edition
This product is designed for use in industrial applications. 3) Remove the special adapter connector cover
Date January 2017 I3+ on the expansion board (fig.A).
Caution for EC Directive
The analog special adapters have been found to be compliant to the European COM3 When connecting this product to another
S
/E
R
8M
-48M
special adapter, please replace the 4)
-4
3U
3U
FX
FX
standards in the aforesaid manual and directive. However, for the very best per- V4+
This manual describes the part names, dimensions, mounting, and specifications formance from what are in fact delicate measuring and controlled output device 'expansion board' in the above description
I4+
of the product. Before use, read this manual and the manuals of all relevant Mitsubishi Electric would like to make the following points; 7(0.28") 74(2.92") with a 'special adapter' and perform the N
15.1 COM4
RU
products fully to acquire proficiency in handling and operating the product. Make As analog devices are sensitive by nature, their use should be considered care-
ST
conduit as high voltage cabling. Where possible users should run analog
Used to connect additional special adapters onto the left side of this special (fig.C) to the C FX
3U R/E
S
cables separately.
- 8M
-48M FX3U-4
*** -
***
3U
FX
adapter.
P
main unit as
O
W
E
Safety Precautions (Read these precautions before use.)
R
• Good cable shielding should be used. When terminating the shield at Earth 6)
[4] Special adapter connector cover: shown on the
This manual classifies the safety precautions into two categories: - ensure that no earth loops are accidentally created.
Remove this cover to connect additional special adapters to the left side. right. RU
N
• When reading analog values, EMC accuracy can be improved out by 6) Slide back the
ST
OP
and . averaging the readings. This can be achieved either through functions on the [5] Direct mounting hole:2 holes of φ4.5 (0.18") (mounting screw: M4 screw)
Not used when connecting to FX3GC/FX 3UC Series PLC. special adapter 5)
analog special adapters or through a users program. 6)
[6] POWER LED (green): slide lock (fig.B)
Indicates that incorrect handling may cause hazardous of the main unit
Lit while 24 V DC power is supplied properly to terminals '24+' and '24-'.
conditions, resulting in death or severe injury. 1. Outline to fix the special 5)
The FX3U-4AD-ADP special adapter for analog input (hereinafter called 4AD-ADP) is a [7] Terminal block (European type):
adapter (fig.C).
Indicates that incorrect handling may cause hazardous Connect the analog voltage/current signal, and 24 V DC power supply.
conditions, resulting in medium or slight personal injury special adapter to add four analog input points.
[8] Special adapter connector:
or physical damage. 1.1 Incorporated Items Used to connect this special adapter to PLC main unit or special adapter. 5) B
Verify that the following product and items are included in the package: [9] DIN rail mounting hook
Connection precautions
Depending on the circumstances, procedures indicated by may [10] Special adapter fixing hook
Product FX3U-4AD-ADP analog input special adapter Connect all the high-speed I/O special adapters before connecting other
also cause severe injury. [11] Special adapter connector: special adapters when they are used in combination.
It is important to follow all precautions for personal safety. Accessories User’s manual (This manual) Used to connect communication or analog special adapters to the left side of the Do not connect a high-speed I/O special adapter on the left side of any
4AD-ADP. special adapters other than other high-speed I/O special adapters.
Associated Manuals
2. Installation
Manual name Manual No. Description
For installation/uninstallation details, refer to the respective PLC User's manual
FX3S /FX3G/FX3GC/FX3U / Describes specifications for Hardware Edition.
JY997D16701 analog control and
FX3UC Series
MODEL CODE: programming method for INSTALLATION
User's Manual FX3S /FX3G/FX 3GC/FX 3U/
09R619 PRECAUTIONS
- Analog Control Edition FX3UC Series PLC.
• Make sure to cut off all phases of the power supply externally before attempting
FX3S /FX3G/FX3GC/FX3U /
installation or wiring work.
FX3UC Series JY997D16601 Describes PLC programming Failure to do so may cause electric shock or damage to the product.
Programming Manual MODEL CODE: for basic/applied instructions
- Basic & Applied 09R517 and devices.
Instruction Edition INSTALLATION
PRECAUTIONS
FX3S Series JY997D48601 E xplains FX 3S Series PLC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Use the product within the generic environment specifications described in PLC
- Hardware Edition 09R535 installation, and maintenance. main unit manual (Hardware Edition).
Never use the product in areas with excessive dust, oily smoke, conductive dusts,
FX3G Series JY997D31301 E xplains FX 3G Series P LC corrosive gas (salt air, Cl 2 , H 2 S, SO 2 , or NO 2 ), flammable gas, vibration or
User’s Manual MODEL CODE: specifications for I/O, wiring, impacts, or expose it to high temperature, condensation, or rain and wind.
- Hardware Edition 09R521 installation, and maintenance. If the product is used in such conditions, electric shock, fire, malfunctions,
FX3GC Series JY997D45401 Explains FX 3GC Series PLC deterioration or damage may occur.
User’s Manual MODEL CODE: specifications for I/O, wiring, • When drilling screw holes or wiring, make sure cutting or wire debris does not
- Hardware Edition 09R533 installation, and maintenance. enter the ventilation slits.
Failure to do so may cause fire, equipment failures or malfunctions.
FX3U Series JY997D16501 E xplains FX 3U S eries P LC
User’s Manual MODEL CODE: specifications for I/O, wiring, • Do not touch the conductive parts of the product directly.
- Hardware Edition 09R516 installation, and maintenance. Doing so may cause device failures or malfunctions.
• Connect special adapter securely to their designated connectors.
FX3UC Series JY997D28701 Explains FX 3UC Series PLC Loose connections may cause malfunctions.
User’s Manual MODEL CODE: specifications for I/O, wiring,
- Hardware Edition 09R519 installation, and maintenance.
<Reference>
Digital output
Input Exclusion of loss in opportunity and secondary loss from warranty liability
DISPOSAL characteristics
Manufacturer Model Caulking tool Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
PRECAUTIONS
(1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
CRIMPFOX 6*1 (2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
Phoenix Contact Co., Ltd. AI 0.5-8WH • Please contact a certified electronic waste disposal company for the 0 4mA 20mA 20.4
(or CRIMPFOX 6T-F*2) 0 10V 10.2V
mA (3) Special damages and secondary damages whether foreseeable or not, compensation for
environmentally safe recycling and disposal of your device. Analog input Analog input
accidents, and compensation for damages to products other than Mitsubishi products.
*1 Old model name: CRIMPFOX ZA 3
TRANSPORTATION AND • The photocoupler is adopted to insulate the analog input area (4) Replacement by the user, maintenance of on-site equipment, start-up test run
*2 Old model name: CRIMPFOX UD 6 from the PLC. and other tasks.
STORAGE PRECAUTIONS Insulation
- Strand wire/single wire - Stick terminal with insulating sleeve • The DC/DC converter is adopted to insulate the power supply
• The product is a precision instrument. During transportation, avoid impacts larger method
Insulation sleeve Contact area
(Crimp area) than those specified in the general specifications by using dedicated packaging
line from the analog input area. For safe use
• Channels are not insulated from each other.
boxes and shock-absorbing palettes. Failure to do so may cause failures in the
Occupied 0 point (This number is not related to the maximum number of • This product has been manufactured as a general-purpose part for general
product. After transportation, verify operation of the product and check for damage
9mm 8mm points input/output points of the PLC.) industries, and has not been designed or manufactured to be incorporated in
of the mounting part, etc.
(0.35") (0.31") a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric
2.6mm(0.1") 14mm(0.55") power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
When using a stick terminal with insulating sleeve, choose a wire with proper • This product has been manufactured under strict quality control. However
cable sheath referring to the above outside dimensions, or otherwise, the wire when installing the product where major accidents or losses could occur if the
cannot be inserted easily. product fails, install appropriate backup or failsafe functions in the system.
The tightening torque must be 0.22 to 0.25 N•m. Do not tighten terminal
screws with a torque outside the above-mentioned range. Failure to do so may
cause equipment failures or malfunctions.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN