Professional Documents
Culture Documents
EXCAVATORS
CHAPTER : Product Description
POWER UP
FINE CONTROL
MODE
Kw
Kw
ECONOMY
AUT
M m in
INSTRUMENT PANEL
If the power mode is on the economy position during trave, engine output
automatically increases by one level to increase travel speed.
Economy 90 % 100 %
Fine Control 70 % 70 %
NOTE: The hammer mode must be activated with Power + Mode and Boom Priority
selected
Page: 15
320B330B HYDRAULIC
EXCAVATORS
CHAPTER : Product Description
POWER CHARACTERISTICS
Power
Up 100 10 2180 rpm
Fine
Control 70 7 1750 rpm
Page: 16
320B330B HYDRAULIC
EXCAVATORS
CHAPTER : Product Description
BOOM UP
PRIORITY
FINE
CONTROL
SWING
PRIORITY
Kw
AUT
M m in
USER
MODE
Only one of the four switches on the left side of the instrument panel may be selected.
When a new switch is selected, the previous switch automatically turns off. If the engine
is switched off, the position of these switches is recorded, and the switches preset to this
position when the engine is started again.
NOTE: The hammer mode must be activated with Power + Mode and Boom Priority selected
Page: 17
320B330B HYDRAULIC
EXCAVATORS
CHAPTER : Product Description
Page: 18
320B330B HYDRAULIC
EXCAVATORS
CHAPTER : Product Description
Kw
UT
A
M m in
1. CLOCK ADJUSTMENT
The hour setting can be changed by pressing Alarm Cancel Switch
and Boom Priority Switch at the same time. The minutes can be
changed by pressing the Alarm Cancel Switch and Power R
BOOM UP
PRIORITY
When this switch is pressed, the flashing figure on the display increases.
SWING
PRIORITY
When this switch is pressed, the flashing figure on the display decreases.
FINE
CONTROL
When this switch is pressed, the flashing digit will move right.
USER
MODE
When this switch is pressed, the flashing digit will move left.
4. SELECTING SUB-MODE
Two digit of left side show Sub-mode
U1- - - - This indicates Tamping Mode. No setting is required for Tamping Mode
U2- - - - This indicates Hammer Mode. The setting of Hammer Mode is available
only in the Service Mode
U3- - - - This indicates Customer Mode. The setting for Customer Mode can now
be set.
NOTE : "- - - -" means no data is displayed
Page: 19
320B330B HYDRAULIC
EXCAVATORS
CHAPTER : Product Description
6 CUSTOMER MODE (First digit shows "U", second digit shows "3")
First
second Third digit Fourth to sixth digits
digit
Page: 20
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 1 of 6
Cerrar SIS
Pantalla anterior
Producto: EXCAVATOR
Modelo: 320B L EXCAVATOR 6CR
Configuración: 320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERED BY 3066 ENGINE
Pruebas y Ajustes
308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B
Excavators Engine and Pump Control
Número de medio -RENR1998-06 Fecha de publicación -01/10/2004 Fecha de actualización -06/10/2004
i01768419
Illustration 1 g00904377
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 2 of 6
Monitor Panel
The Electronic Monitor Panel will activate. Then, the monitor will display the output that is received from
the controller. The Controller Service Program is divided into five functions. Each function is listed:
• Displaying the machine conditions (engine speed, hydraulic oil temperature, power shift pressure, etc)
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 3 of 6
• The electronic control components are adjusted and tested. The adjustment codes are listed: 70 and 71.
The test codes are listed: 60, 61, 62, 66 and 67.
Service codes: 80 to 8A
You should depress the switches on the monitor panel in order to start up the service program or the switches
are depressed in order to change the functions. The corresponding switch and/or switches should be
depressed until the required function is displayed on the character display.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 4 of 6
Illustration 2 g00662936
Note: The engine can be running or the engine can be stopped, when the "Service Mode" is started. When
the engine is stopped, the starter switch must be in the ON position. You should know the procedure to start
up the "Service Mode" in advance.
1. The following switches should be depressed and held for 2 seconds or more simultaneously: travel
alarm cancel switch (22), fine control mode switch (25) and user mode switch (26) .
2. The time display and the dial display on the character display (2) will change to a "0" and a "0". The
left character position will flash.
Note: The security code must be entered within 10 seconds after the first procedure (1). Otherwise, the
time display will return. You should learn the procedure of entering the security code in advance.
a. The figure that is blinking on the character display (2) can be changed. In order to change the
figure, you should depress the boom priority mode switch (23) or the swing priority mode
switch (24).
■ The figure that is blinking increases (Boom priority mode switch (23) )
■ The figure that is blinking decreases (Swing priority mode switch (24) )
The character position that is blinking can be shifted by depressing the fine control mode switch
(25) or the user mode switch (26).
■ The character position that is blinking shifts to the right (Fine control mode switch (25) ).
■ The character position that is blinking shifts to the left (User mode switch (26) ).
5. After you enter the security code, the service mode is activated by depressing and holding the
following switches for 2 seconds or greater: travel alarm cancel switch (22), fine control mode switch
(25) and user mode switch (26). The service mode is automatically activated 10 seconds after the
security code is entered.
6. Now, the "Service Mode" is activated and the character display (2) will display "10" on the left two
character positions and "1" on the right character position.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 5 of 6
◦ The figure that is blinking increases (Boom priority mode switch (23) )
◦ The figure that is blinking decreases (Swing priority mode switch (24) )
2. The position that is blinking on the character display (2) can be shifted by depressing the fine control
mode switch (25) and the user mode switch (26) .
◦ The position that is blinking shifts to the right (Fine control mode switch (25) )
◦ The position that is blinking shifts to the left (Swing priority mode switch (24) )
Note: Refer to the chart of Service Codes for selecting the functions for the "Service Mode".
Table 1
Service
Function
Code
10 Automatic Travel Speed Change
11 Low Temperature Control
12 Engine Speed
13 Engine Coolant Temperature
14 Hydraulic Oil Temperature
16 Digital Input
17 Software Version
18 Real Time Error Code
19 Error Log
1a Engine Speed Dial Setting Check
1b Model Name and Engine Type
1c Real Time Error Code (ATT)
1d Error Log (ATT)
20 Power Shift Pressure Command Signal
21 Displays Higher Delivery Pressure Of Main Pumps
60 Proportional Reducing Valve Sweep Test
61 Governor Actuator Sweep Test
62 ON/OFF Test Of Digital Output
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012
320B & 320B L TRACK-TYPE EXCAVATORS 6CR00001-UP (MACHINE) POWERE... Page 6 of 6
2. The following switches should be depressed and held simultaneously for 2 second or more:
The service mode has been stopped, if the character display shows the position of the engine speed
dial on the right two character positions and the time is shown on the left four character positions.
Copyright 1993 - 2012 Caterpillar Inc. Mon Jan 16 15:41:45 CST 2012
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 1/16/2012