Professional Documents
Culture Documents
xls 文档密级:
Select
Ver: 1.5
dards
dards
andards
andards
Never distribute the signal cable on the heat radiation mesh on the top of cabinet, which effect heat
4.1.003 MAJ 2 000000G
radiation and reduce cable’s life.
The trunk cable connector must be firmly fixed. The cable connector made on-site must be according to
4.1.005 MAJ 2 000000G
special specifications. Its connector needs to be fixed firmly with a perfect appearance.
The signal cable must be arranged according to engineering design document. Convenient to maintenance
4.1.008 MED 0.5 000000J
and expansion.
4.1.009 Cable routing of the signal cable inside cabinet must be correct. MED 0.5 000000J
Distribution of cables outside cabinet:
1. The cable must be distributed without any cross and bending.
2. Put the cable in the cable trough without binding, and the cable cannot overflow the trough.
3. When cable ladder is adopted, the cable must be fixuped and tied in order at the beam of cable ladder.
4.1.010 When the spacing between the cable ladder and the top of the cabinet is more than 0.8 m, a cable ladder MED 0.5 000000J
must be added on the top of cabinet to reduce stress caused by weight of the cable.
4. When several layers of cables are distributed under the floor in an overlapped way, their height cannot be
higher than 3/4 of the height of the space below the antistatic floor.
5. The cable must be tied in order in case of no cable trough.
The bending position of signal cable must be smooth. It is suggested that necessary protective measures
4.1.011 MED 0.5 000000J
must be taken when signaling cables are fixed to mechanical parts with edges and corners.
Cables must be tied with uniform spacing and appropriate tightness. Cable ties must be arranged in a tidy
4.1.014 way. Their redundant parts must be cut from their bottom after they are tied so that any sharp edges do not MED 0.5 000000J
exist.
4.1.015 The signal cable route must be straight but its bending position must be smooth. MED 0.5 000000J
4.1.020 The unused fiber ends or optical ports of board should be covered with protection caps. MED 0.3 000000K
Signal cables must be arranged straight,flatly and neatly without crossing (cables are allowed to be crossed
4.1.024 MIN 0.2 000000L
within 1m outside cabinet), there is somewhat longer than necessary at the bending point.
Fibers: Common
5.1.001 When the tail fiber is led out of the cabinet, it must be protected. MAJ 3 000000F
The connection point of tail fiber must be clean without any dust. The unused optical fiber head and board
5.1.002 optical port must be covered with protection caps (plugs). They can be cleaned according to the company MAJ 2 000000G
specifications.
Distribution of tail fibers:
1. When tail fibers are distributed at bending positions, they must not be too tight and cross there. A pair of
5.1.003 tail fibers must be tied neatly with moderate tightness. MAJ 2 000000G
2. Tail fibers can be drawn freely from the ring of cable tie. They cannot be bent into a right angle.
3. After tail fibers are distributed, other cables or things cannot be put on them.
5.1.004 The protection tube must enter into the cabinet with a length of less than 10 cm, and be tied firmly. MED 0.5 000000J
The cut of protection tube for tail fiber must be smooth. Otherwise, the insulating tape must be used to avoid
5.1.005 MED 0.5 000000J
hurting anyone.
Labels
The labels of cable are filled in and stuck correctly and reliably. They must be tidy position and same
7.1.005 direction. They must be stuck on a position 2 cm away from their connectors. They can be made in a MED 0.5 000000J
uniform way according to customer requirement.
The labels of power cable and ground cable are filled in and stuck correctly and reliably. They must be in a
tidy position and the same direction. They must be stuck on a position about 2cm away from their
7.1.006 MED 0.3 000000K
connectors. They can be made in a uniform way according to customer requirements, including the label for
power distribution switch.
7.1.011 The labels of rack shall be placed neat and clean. MIN 0.2 000000L
The row and column labels of the cabinet must be stuck in a clear and tidy way. If there has a dashed box
7.1.012 on the cabinet, MIN 0.2 000000L
labels must be stuck within it.
Base station product installation of rack
When a micro base station is put up on the wall or is put on its support, its installation must be firm without
8.1.001 MAJ 3 000000F
any loose connection.
8.1.002 Setting of DIP switches & jumpers are properly set in BTS MAJ 1 000000I
The rigid cables must not be cross inside the cabinet. They cannot be pulled too tightly. Some redundancy
8.1.008 MED 0.5 000000J
must be reserved at their bend place. They also need to be bent in a tidy and consistent way.
The fan must be tightened with screws so that its installation is firm. Its switch, rotation and alarm work
8.1.011 MED 0.5 000000J
normally.
8.1.022* The rack must be firmly fixed on its base (bracket) after it is installed. MAJ 3 000000F
8.1.023* The parts of the rack must not be distorted. Which may be affect the equipment appearance. MED 1 000000I
The cabinet or its base (bracket) is firmly fixed on the ground with expansion bolts. All of insulation washers,
8.1.024* MED 1 000000I
flat washers, spring washers, bolts and nuts are installed in a correct order.
8.1.025* The movable accessories of the cabinet work normally. MED 0.5 000000J
Antenna and Feeder Installation
The connection of the lightning-proof arrester connector in the cabinet is reliable. When there is a reliable
grounding point outside the room, the feeder cable must be earthed outside the room. Water-proof
9.1.001 MAJ 5 000000D
measures must be made for the feeder cable ground. The feeder inside the room should be earthed the
operation room main protection grounding before the feeder connect with equipment.
9.1.002 Antennas must be in the 45-degree protected area of lightning rod. MAJ 4 000000E
9.1.003 The feeder cables must not have obvious bending and twisting and bare copper appearance. MAJ 4 000000E
9.1.004 The connector of feeder cable is made in a standard way without any loose connection. MAJ 4 000000E
The bending position of signal cable must be smooth. It is suggested that necessary protective measures
◆ 4.1.011 MED 0.5 000000J
must be taken when signaling cables are fixed to mechanical parts with edges and corners.
◇ 4.1.012 Cables must be tied in a tidy way and do not affect the distribution and future expansion of other cables. MED 0.5 000000J
When multiple-core trunk cables and subscriber cables are distributed inside the cabinet, they must be tied
◇ 4.1.013 in a rectangle at the beam beside the pole without any cross and bending and arranged clearly. Single-core MED 0.5 000000J
trunk cables must be distributed in an orderly way without any cross and bending.
Cables must be tied with uniform spacing and appropriate tightness. Cable ties must be arranged in a tidy
◆ 4.1.014 way. Their redundant parts must be cut from their bottom after they are tied so that any sharp edges do not MED 0.5 000000J
exist.
◆ 4.1.015 The signal cable route must be straight but its bending position must be smooth. MED 0.5 000000J
The auxiliary cables for terminals, operators and alarm boxes must be distributed and tied in an orderly way.
◇ 4.1.016 MED 0.5 000000J
The redundant cable ties must be cut from their bottom so that any sharp edges do not exist.
PVC troughs must be installed on the wall for power cable and signal cable of alarm box. Redundant power
◇ 4.1.017 MED 0.3 000000K
cable and signal cable must be put under the floor or the cabling ladder at alarm box side.
◇ 4.1.018 For upward or downward cabling, cables must be bent at the top or bottom of the rack, redundant length MED 0.3 000000K
must be reserved, and the marks at both ends must be clear.
When trunk cables are bound between frames, a cable tie must be used to bind each trunk cable on the
◇ 4.1.019 MED 0.3 000000K
cable support.
◆ 4.1.020 The unused fiber ends or optical ports of board should be covered with protection caps. MED 0.3 000000K
◇ 4.1.021 Cables must be peeled off tidily at output cable holes of the sub-rack in case of peeling off is required. MIN 0.2 000000L
◇ 4.1.022 The bending radius of coaxial cable must not be less than 4cm. MIN 0.2 000000L
◇ 4.1.023 The peeled place of subscriber cable at the MDF should be covered with the adhesive tape or heat-shrinkable MIN 0.2 000000L
Signal cables must be arranged straight,flatly and neatly without crossing (cables are allowed to be crossed
◆ 4.1.024 MIN 0.2 000000L
within 1m outside cabinet), there is somewhat longer than necessary at the bending point.
Arrange the cables in an orderly and good-looking way, the cables must be bundled with evenly distributed
◇ 4.1.025 MIN 0.2 000000L
space and proper tightness.
◇ 4.1.026
◇ 4.1.027
◇ 4.1.028
◇ 4.1.029
◇ 4.1.030
◇ 4.1.031
◇ 4.1.032
◇ 4.1.033
◇ 4.1.034
◇ 4.1.035
◇ 4.1.036
◇ 4.1.037
◇ 4.1.038
◇ 4.1.039
◇ 4.1.040
◇ 10.4.031
◇ 10.4.032
◇ 10.4.033
◇ 10.4.034
◇ 10.4.035
◇ 10.4.036
◇ 10.4.037
◇ 10.4.038
Repeater Test
◇ 10.5.001 Total attenuation from A to B and from B to A :Meet the design requirements MAJ 3 000000F
◇ 10.5.002 The total section loss of A - B or B – A:Meet the design requirements MAJ 3 000000F
◇ 10.5.003 The optical signal backscatter trace of A - B or B – A:Meet the design requirements MAJ 3 000000F
◇ 10.5.004
◇ 10.5.005
◇ 10.5.006
◇ 10.5.007
◇ 10.5.008
◇ 10.5.009
◇ 10.5.010
◇ 10.5.011
◇ 10.5.012
◇ 10.5.013
◇ 10.5.014
◇ 10.5.015
◇ 10.5.016
◇ 10.5.017
◇ 10.5.018
◇ 12.1.008 The dimensions of base section must meet the design requirements, and the deviation must be +15/-10mm MAJ 6 000000C
The base backfill records are complete and correct
1. Soil appearance: no rubbish, organics or humus allowed;
2. Soil moisture: No rubber soil or airborne dust allowed;
◇ 12.1.009 MED 3 000000F
3. layer thickness: 300 mm (mechanical);
4. Density: In compliance with design requirements or not less than 90%;
5. Top level: Tolerance: 20 mm;
◇ 12.1.010 Check the smoothness of the base surface. The deviation must be ≤5mm MED 3 000000F
Check the appearance of the base: No concave, spongy surface, crack (crack on the surface ≤1mm),
◇ 12.1.011 MED 3 000000F
defects of appearance, and so on
The intensity of the concrete must meet the design requirements. The intensity after 28-day maintenance
◇ 12.1.012 MED 3 000000F
must not be less than C20.
The antistatic plate is pressed to make it flat at the four sides of the square compartment by using the hold-
◇ 12.1.013 MED 3 000000F
down strip of the plate and clinch bolts, and a conductor is formed.
The equipment room is installed properly and securely on its base, and the structure is kept intact without
◇ 12.1.014 MED 3 000000F
distortion
For the cement base on the floor: The distance to the floor, the intensity of the base and the levelness
◇ 12.1.015 deviation must conform to the design requirements. The levelness deviation of the base must be no more MED 3 000000F
than 3mm/m; For the overhead cement base: Check
◇ 12.1.016 Grounding cables have been buried in advance as designed, and the records are complete. MED 3 000000F
Diesel generator foundation: The thickness is 3~4 times of the diameter of the cylinder of the diesel
◇ 12.1.017 MED 3 000000F
generator.
Diesel generator foundation: A sloping ground for cleaning must be available directly under the oil sump
◇ 12.1.018 tank on the central line of the crankshaft. In addition, there must be a ditch to discharge to the main MED 3 000000F
pollution discharge ditch.
Diesel generator foundation: The base must be surrounded by the cable ditch of diesel generator, oil and
◇ 12.1.019 MED 3 000000F
fuel pipe ditch (for the purpose of vibration isolation, antivibration and pollution discharge).
◇ 12.1.020 Diesel generator foundation: The base is flat and solid, and in good condition. MED 3 000000F
◇ 12.1.021 Soil or grass turfing as per requirement MED 3 000000F
◇ 12.1.022 Geologic survey report MED 3 000000F
◇ 12.1.023 Structural mechanical analysis report (applicable to roof site) MED 3 000000F
◇ 12.1.024 Backfill compactness inspection report MED 3 000000F
◇ 12.1.025 Raw material certificate and test report MED 3 000000F
◇ 12.1.026
◇ 12.1.027
◇ 12.1.028
◇ 12.1.029
◇ 12.1.030
◇ 12.1.031
◇ 12.1.032
◇ 12.1.033
◇ 12.1.034
◇ 12.1.035
◇ 12.1.036
◇ 12.1.037
◇ 12.1.038
◇ 12.1.039
◇ 12.1.040
Roof Site Foundation Work
◇ 12.2.001 Joint surface between new structure and old structure: Rough, clean, wet MED 3 000000F
◇ 12.2.002 Foundation position: In compliance with design requirements MED 3 000000F
◇ 12.2.003 Waterproof of roof: No leakage MED 3 000000F
◇ 12.2.004 Tensile strength of anchor bolt: In compliance with design requirements MED 3 000000F
◇ 12.2.005 Structure restoration: Complete and without trash MED 3 000000F
◇ 12.2.006 Foundation dimension: 10mm MED 3 000000F
◇ 12.2.007 Foundation level: 10mm MED 3 000000F
◇ 12.2.008
◇ 12.2.009
◇ 12.2.010
◇ 12.2.011
◇ 12.2.012
◇ 12.2.013
◇ 12.2.014
◇ 12.2.015
◇ 12.2.016
◇ 12.2.017
◇ 12.2.018
◇ 12.2.019
◇ 12.2.020
◇ 12.2.021
◇ 12.2.022
Site Final Surface
◇ 12.3.001 Material Specifications: In compliance with design requirements MED 3 000000F
◇ 12.3.002 Slope and level of base course: In compliance with design requirements MED 3 000000F
◇ 12.3.003 Top layer thickness: In compliance with design requirements MED 3 000000F
◇ 12.3.004 Surface plainness: In compliance with design requirements MED 3 000000F
◇ 12.3.005 Expansion joint: In compliance with design requirements MED 3 000000F
◇ 12.3.006 Overall appearance: Tidy and clean MED 3 000000F
◇ 12.3.007
◇ 12.3.008
◇ 12.3.009
◇ 12.3.010
◇ 12.3.011
◇ 12.3.012
◇ 12.3.013
◇ 12.3.014
◇ 12.3.015
◇ 12.3.016
◇ 12.3.017
◇ 12.3.018
◇ 12.3.019
◇ 12.3.020
◇ 12.3.021
Civil Work
◇ 12.4.001 Brick laying records MAJ 6 000000C
◇ 12.4.002 Check that the dimensions and azimuth of the equipment room meet the design requirements MAJ 6 000000C
◇ 12.4.003 Check the verticality of each wall. The allowable deviation is 10mm MAJ 6 000000C
◇ 12.4.004 Check that the location of the grounding copper busbar meet the design requirements MAJ 6 000000C
Smoothness of the surface (the allowable deviation for the cement mortar is 4mm; the allowable deviation
◇ 12.4.005 MED 3 000000F
for the terrazzo is 3mm; and the allowable deviation for the ground tile is 2mm)
The locations where the steel doors and windows and the direction towards which they are opened meet
◇ 12.4.006 MED 3 000000F
the design requirements
The levelness of the frames of doors and windows meet the design requirements (the allowable deviation is
◇ 12.4.007 MED 3 000000F
3mm)
◇ 12.4.008 Deviation of the two diagonals of the door and window frames (the allowable deviation is 5mm) MED 3 000000F
◇ 12.4.009 The walls of the equipment room is water resistant MED 3 000000F
The cabling rack is mounted securely and uprightly at the correct position and meets the design
◇ 12.4.010 MED 3 000000F
requirements
◇ 12.4.011 The fluorescent lamps and the switches are working MED 3 000000F
◇ 12.4.012 The period of validity of the portable extinguisher does not expire MED 3 000000F
◇ 12.4.013 The equipment room is clean and free of dust and sundries MED 3 000000F
Check the walls of the equipment room. The seam must be covered properly without holes or cracks. The
◇ 12.4.014 MED 3 000000F
paint for the inner wall must not be too dense and smooth
Some porous materials, such as cement, lime paste and wood dust, must be added in the painting material
◇ 12.4.015 MED 3 000000F
to absorb noise.
◇ 12.4.016 Sound isolation materials must be used as the ceiling board MED 3 000000F
Ventilation and cooling measures have been taken for the equipment room: The location, dimensions and
◇ 12.4.017 installation technologies of each incoming air pipe and outgoing air pipe must conform to the design MED 3 000000F
drawings
◇ 12.4.018
◇ 12.4.019
◇ 12.4.020
◇ 12.4.021
◇ 12.4.022
◇ 12.4.023
◇ 12.4.024
◇ 12.4.025
◇ 12.4.026
◇ 12.4.027
◇ 12.4.028
◇ 12.4.029
◇ 12.4.030
◇ 12.4.031
◇ 12.4.032
Fence Installation
◇ 12.5.001 The specifications, dimensions and styles conform to the design requirements MAJ 6 000000C
◇ 12.5.002 It is vertical, flat and fastened MAJ 6 000000C
◇ 12.5.003 The coating of the Fence component complies with the design and specifications requirements MAJ 6 000000C
◇ 12.5.004 The spray paint of the Fence component complies with the design and specifications requirements MAJ 6 000000C
◇ 12.5.005 The doors and locks accord with requirements and works normally MAJ 3 000000F
◇ 12.5.006 Material: In compliance with design requirements MED 3 000000F
◇ 12.5.007 Gate: Can operate and be locked well MED 3 000000F
◇ 12.5.008 Fence installation: Reliably installed MED 3 000000F
◇ 12.5.009 Fence appearance: Tidy and clean MED 3 000000F
◇ 12.5.010 Construction of concrete foundation: In compliance with design requirements MED 3 000000F
◇ 12.5.011 Constructional Column: In compliance with design requirements MED 3 000000F
◇ 12.5.012
◇ 12.5.013
◇ 12.5.014
◇ 12.5.015
◇ 12.5.016
◇ 12.5.017
◇ 12.5.018
◇ 12.5.019
◇ 12.5.020
◇ 12.5.021
◇ 12.5.022
◇ 12.5.023
◇ 12.5.024
◇ 12.5.025
◇ 12.5.026
Lamps, sockets and switches are firmly and properly fixed; sockets and lighting equipment are correctly
◇ 13.1.028 MED 3 000000F
installed; switches function properly.
◇ 13.1.029 Cabling holes of air-conditioner: All cabling holes are watertight. MED 3 000000F
◇ 13.1.030 ITS overall appearance: Overall appearance of the equipment room is in good condition. MED 3 000000F
◇ 13.1.031
◇ 13.1.032
◇ 13.1.033
◇ 13.1.034
◇ 13.1.035
◇ 13.1.036
◇ 13.1.037
◇ 13.1.038
◇ 13.1.039
◇ 13.1.040
◇ 13.1.041
◇ 13.1.042
◇ 13.1.043
◇ 13.1.044
◇ 13.1.045
3 Owners
Owner: head of Delivery Business Dept of sub-regional divisions
Owners of different links:
Authors of FAT reports: engineers (including those of Huawei and Cooperation Partners) and clerks
Signers of FAT reports: owners of projects (including those of Huawei and Cooperation Partners)
◇ 22.1.009 MAJ 2 000000G
Recording of FAT progress in EPMS: engineers (including those of Huawei and Cooperation Partners)
and clerks
Uploading of scanned copy of FAT reports to EPMS: engineers (including those of Huawei and
Cooperation Partners) and clerks