Professional Documents
Culture Documents
Refer to the exhibit. The output of the show ip route command for router R1 is displayed. What action will the
router take for a packet that is destined for 192.168.1.5?
It will drop the packet.
It will determine the route for the packet through a routing protocol.
2 Top of Form
Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which
two facts are true about the forwarding of route information by R1? (Choose two.)
R1 will forward the route information for subnet 192.168.100.0/30.
R1 will forward the route information with an administrative distance set to 50.
R1 will forward route information for subnet 10.10.10.0/30 out the serial interface.
Bottom of Form
3 Top of Form
A router has EIGRP configured as the only routing protocol. In what way might EIGRP respond if there is no
feasible successor route to a destination network and the successor route fails?
It broadcasts hello packets to all routers in the network to re-establish neighbor adjacencies.
4 Top of Form
When a router boots, what is the default order to locate the Cisco IOS if there is no boot system command?
ROM, TFTP server, flash
flash, TFTP server, ROM
5 Top of Form
Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?
The Dijkstra algorithm will calculate the feasible successor.
Traffic destined to the 192.168.1.0 network will be dropped immediately due to lack of a feasible succes
Bottom of Form
6 Top of Form
What should be considered when troubleshooting a problem with the establishment of neighbor relationships
between OSPF routers? (Choose two.)
OSPF interval timers mismatch
7 Top of Form
What is the first step OSPF and IS-IS routers take in building a shortest path first database?
learn about directly connected networks
flood LSPs to all neighbors informing them of all known networks and their link states
Bottom of Form
8 Top of Form
Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which
statement is true regarding how the routers in this topology will respond to this event?
Router5 flushes the unreachable route from its routing table in 30 seconds.
Router4 will learn about the failed route 30 seconds later in the next periodic update.
Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.
Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown tim
expires.
Bottom of Form
9 Top of Form
A network is configured with the IP, IPX, and AppleTalk protocols. Which routing protocol is recommended
this network?
RIPv1
RIPv2
EIGRP
OSPF
Bottom of Form
10 Top of Form
Refer to the exhibit. Although both the routers can ping the serial interface of their neighbors, they are unable
ping the Ethernet interfaces of other routers. Which two statements are true for this network? (Choose two.)
The administrative distance has been set to 50 on both routers.
The network 10.1.1.0 command has not been run on both routers.
11 Top of Form
The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with
addressing scheme. What is the problem with the addressing used in the topology?
The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that subnetwork.
The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwor
assigned to Ethernet0 of Router3.
The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork from the addres
for Serial0 of Router2.
The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned to Ethernet0 of
Router3.
Bottom of Form
12 Top of Form
Refer to the exhibit. What action will R2 take for a packet that is destined for 192.168.2.0?
It will drop the packet.
13 Top of Form
Refer to the exhibit. The network administrator issues the command no ip classless on Router1. What
forwarding action will take place on a packet that is received by Router1 and is destined for host 192.168.0.2
The packet will be dropped.
The packet will match the 192.168.0.0 network and be forwarded out Serial 0/0.
The packet will most closely match the 192.168.0.8 subnet and be forwarded out Serial 0/1.
Bottom of Form
14 Top of Form
Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet network attached to R3. R1
learned Path A to network 10.2.0.0/16 from a static route and Path B to network 10.2.0.0/16 from EIGRP. W
route will R1 install in its routing table?
Both routes are installed and load balancing occurs across both paths.
The route via Path B is installed because the EIGRP route has the best metric to network 10.2.0.0/16.
The route via Path A is installed because the static route has the best metric to network 10.2.0.0/16.
The route via Path B is installed because the EIGRP route has the lowest administrative distance to netw
10.2.0.0/16.
The route via Path A is installed because the static route has the lowest administrative distance to networ
10.2.0.0/16.
Bottom of Form
15 Top of Form
Refer to the exhibit. What information can be determined from the highlighted output?
R1 is originating the route 172.30.200.32/28.
Router2
Router3
Router4
Bottom of Form
17 Top of Form
Which two components are used to determine the router ID in the configuration of the OSPF routing process
(Choose two.)
the IP address of the first FastEthernet interface
18 Top of Form
Which two statements are true regarding link-state routing protocols? (Choose two.)
They are aware of the complete network topology.
They do not work well in networks that require special hierarchical designs.
They pass their entire routing tables to their directly connected neighbors only.
Bottom of Form
19 Top of Form
What is the function of the OSPF LSR packet?
It is used to confirm the receipt of LSUs.
It is used by the receiving routers to request more information about any entry in the DBD.
20 Top of Form
Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is tru
regarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
The router chooses the first path that it learned and installs only that route in the routing table.
The router chooses the path with the lowest administrative distance and installs only that route in the rou
table.
The router chooses the highest routing ID based on the advertised network IP addresses and installs only
route in the routing table.
The router installs all the equal cost paths in the routing table but sends packets out only one, holding the
others in reserve in case the primary route goes down.
The router installs all the equal cost paths in the routing table and performs equal cost load balancing to s
packets out multiple exit interfaces.
Bottom of Form
21 Top of Form
A network is using RIP as the routing protocol. The router learns that the same destination can be reached via
five different paths. All paths have the same metric, and all routers are using the default operation.
Bottom of Form
22 Top of Form
Refer to the exhibit. All routers are running the same routing protocol. Based on the exhibit and its displayed
commands, which statement is true?
The wildcard mask is incorrectly configured.
The link to the ISP is not advertised by the routing protocol process.
Bottom of Form
23 Top of Form
Which two statements are true about the startup configuration in a router? (Choose two.)
The router uses the startup configuration file to start POST.
If the Cisco IOS cannot be found, the router enters setup mode.
The bootstrap program searches for the startup configuration file in NVRAM.
If the startup config file cannot be found, the router enters ROMMON mode.
The router searches for a TFTP server if the startup configuration file is absent at the default location.
Bottom of Form
24 Top of Form
A network administrator has been asked to configure a network using a classful IP addressing scheme. Which
statement is true about the IP addressing that will be used?
Classful IP addresses can be used only when static routing is configured in the network.
Classful IP addresses allow the network/host boundary to occur at any bit in the 32-bit address.
The subnet mask for classful IP addresses can be determined by the value of the first octet of the IP addr
Classful IP addresses require the subnet mask to be included in the routing updates that are propagated b
the classful routing protocols.
Bottom of Form
25 Top of Form
Refer to the exhibit. All routes are advertised and fully operational on all routers. Which statement is true abo
the path that the data will take from router A to router B?
If EIGRP is used with default configurations, the data will be equally distributed between two paths — A
D, B and A, C, B.
If RIPv1 is used with default configurations, the data will be load-balanced on all paths.
If EIGRP and OSPF are both used with default configurations, the data will be sent through paths learned
the OSPF protocol.
If RIPv2 is used with default configurations, the data will be equally distributed between two paths — A
B and A, C, D.
Bottom of Form
26 Top of Form
Refer to the exhibit. The network administrator is testing network connectivity by issuing the tracert comma
from host A to host B. Given the exhibited output on host A, what are two possible routing table issues on th
network? (Choose two.)
Router1 is missing a route to the 172.16.0.0 network
27 Top of Form
Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this?
The two routers are connected on a multiaccess network.
The hello and dead intervals are different on the two routers.
28 Top of Form
What are two functions of a router? (Choose two.)
It connects multiple IP networks.
29 Top of Form
What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency?
(Choose two.)
The routers must elect a designated router.
The routers must agree on the network type.
30 Top of Form
A network administrator uses the RIP routing protocol to implement routing within an autonomous system.
What are two characteristics of this protocol? (Choose two.)
It uses the Bellman-Ford algorithm to determine the best path.
The Suffolk router is directly connected to the networks shown in the graphic and has a default route that poi
to the Richmond router. All interfaces are active and properly addressed. However, when the workstation on
network 172.29.5.0/24 sends a packet to destination address 172.29.198.5, it is discarded by the Suffolk route
What can be a reason for this result?
IP classless has been disabled on the Suffolk router.
32 Top of Form
Refer to the exhibit. A network administrator successfully pings R1 from R3. Next, the administrator runs the
show cdp neighbors command on R3. The output of this command is displayed.
What are two reasons for the absence of R1 in the output? (Choose two.)
There is a Layer 2 connectivity problem between R1 and R3.
The no cdp enable command has been run at Fa0/1 interface of R3.
R1 is powered off.
Bottom of Form
33 Top of Form
Refer to the exhibit. Both routers are using the RIP protocol. Devices on the 192.168.1.1 network can ping th
S0/0/0 interface on R2 but cannot ping devices on the 192.168.2.1 network.
34 Top of Form
Refer to the exhibit. The routers are properly configured using a dynamic routing protocol with default settin
and the network is fully converged. Router A is forwarding data to router E. Which statement is true about th
routing path?
If the network uses the RIP protocol, router A will determine that all paths have equal cost.
If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table.
If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest c
If both RIP and EIGRP protocols are configured on router A, the router will use the route information tha
learned by the RIP routing protocol.
Bottom of Form
35 Top of Form
Refer to the exhibit. All interfaces are configured with the correct IP addresses and subnet masks. OSPF has
been configured as the routing protocol. During troubleshooting, it is determined that hosts on network B can
ping the Lo0 interface on R1 but are unable to reach hosts on network A. What is the cause of the problem?
Routers R1 and R2 have incorrect router IDs configured.
The configuration of router R1 fails to include network A in the OSPF routing process.
Bottom of Form
36 Top of Form
Refer to the exhibit. A network administrator has configured R1 as shown, and all interfaces are functioning
correctly. A ping from R1 to 172.16.1.1 fails. What could be the cause of this problem?
The serial interface on R1 is configured incorrectly.
37 Top of Form
What are two reasons for the occurrence of a routing loop? (Choose two.)
slow convergence
38 Top of Form
Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational ho
on the Internet fail. What is the reason for this problem?
The FastEthernet interface of R1 is disabled.
39 Top of Form
Refer to the exhibit. What summary address can Router2 advertise to Router1 to reach the three networks on
Routers 3, 4, and 5 without advertising any public address space or overlapping the networks on Router1?
172.16.0.0/8
172.16.0.0/10
172.16.0.0/13
172.16.0.0/20
172.16.0.0/24
Bottom of Form
40 Top of Form
What are three features of CDP? (Choose three.)
tests Layer 2 connectivity
41 Top of Form
Refer to the exhibit. Which statement is true concerning the routing configuration?
Using dynamic routing instead of static routing would have required fewer configuration steps.
The 10.1.1.0/24 and 10.1.2.0/24 routes have adjacent boundaries and should be summarized.
Packets routed to the R2 Fast Ethernet interface require two routing table lookups.
42 Top of Form
3
4
6
Bottom of Form
43 Top of Form
Refer to the exhibit. Router R2 is configured properly and all interfaces are functional. Router R1 has been
installed recently. Host A is unable to ping host B.
44 Top of Form
A network administrator needs to configure a single router to load-balance the traffic over unequal cost paths
Which routing protocol should the administrator use?
EIGRP
OSPF
RIPv1
RIPv2
Bottom of Form
45 Top of Form
Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of
192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network
properly. What is the cause?
The default gateway is incorrect.
Refer to the exhibit. To implement the RIPv2 protocol, the network administrator runs the commands as
displayed. However, the show ip protocol command fails to display any output. How can the administrator
solve the problem that is indicated by the lack of output from this command?
Include the default-information originate command.
Include the no auto-summary command.
47 Top of Form
Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to R3. Which subnet address should
used for the new subnet that provides enough addresses while wasting a minimum of addresses?
192.168.1.0/24
192.168.1.48 /28
192.168.1.32/27
192.168.1.64/26
Bottom of Form
48 Top of Form
Refer to the exhibit. The show cdp neighbors command was run at R1. Which two facts about the newly
detected device can be determined from the output? (Choose two.)
ABCD is a router that is connected to R1.
49 Top of Form
Refer to the exhibit. All router interfaces are configured with an IP address and are operational. If no routing
protocols or static routes are configured, what information will be included in the show ip route command
output for router A?
All of the 192.168.x.0 networks will be in the routing table.
Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24 will be in the routing table.
The routing table will be empty because routes and dynamic routes have not been configured.
A default route is automatically installed in the routing table to allow connectivity between the networks
Bottom of Form
50 Top of Form
Refer to the exhibit. All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unabl
access each other. What can be the cause of this problem?
Because RIPv1 is a classless protocol, it does not support this access.