Professional Documents
Culture Documents
WIRING DIAGRAMS 0
ELECTRICAL
WIRING
HEADLIGHT TAILLIGHT SYSTEM
MODEL DIAGRAM
(WATT) (WATT) OUTPUT
PAGE
(WATT)
Tundra R Annex 1 60/55 hal. 8/27 240
Skandic 380/500 Annex 2 60/55 hal. 8/27 240
Formula S
Annex 3 60 /55 hal. 8/27 240
MX Z 440
Formula DLX 380/500
Annex 4 60 /55 hal. 8/27 220
Touring E/LE/SLE
Formula 500 LC Annex 5 60 /55 hal. 8/27 220
Touring 500 LC
Annex 6 60 /55 hal. 8/27 220
Formula DLX 500 LC
Skandic WT/SWT Annex 7 60 /55 hal. 8/27 240
Skandic WT LC Annex 8 60 /55 hal. 8/27 220
hal. = halogen
11-01-1
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
11-01-2
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
XX/XX
1 - MC
A00I04G
1 D
7
6
11 3
9 8 4 2 1
5 10
A06H33C
AREA LOCATION
1 Front of engine compartment
2 Magneto
3 Carburetors
4 Near of intake silencer
5 Near driven pulley
6 Under console
7 Under hood
8 Near fuel tank
9 Rear of seat
10 Under engine
11 On injection oil reservoir
CONNECTOR LOCATION IN
HOUSING
XX/XX
1- MC
D
A00I04H
D
11-01-3
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
DEUTSCH
85
A A B 2 87
1
87a
B B A 1 86 30 2
2
1
A A
A A
A
B B
C C B B
B
C
A
B
C C A 3
A 1
B 21
A C B 2
A C 3
B B
A B A C
C B
D A B
C B D A B A
C
A B
A B
D C A
B A B 4
C D 1
2
3
1
4 2
3
PACKARD
A A
B B
C
6
5
1 4 1
2 2
3 6 3
5
4
A
A
B B
A C
B A
C 12
D CB 11
ED
1 10 1
2
F 2
3 12
9
8 3
4 11 7 4
5 10 5
6 9 6
8
A 7
A
B CB
D
V01G0ES D
C FE
11-01-4
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
SYMBOLS DESCRIPTION
Beam and tail light Female terminal Male terminal Electronic module
Frame
A00E55S
11-01-5
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
UNPLUGING CONNECTORS
Always unplug connectors by pulling on housing 1
not on wire.
A00E1EA
A06E1PA
Locking Receptacle Connector
TYPICAL
To remove:
– Insert tool Snap-on TT 600-5 in access opening
TAB AND RECEPTACLE then pull housing toward wire side.
CONNECTORS REMOVAL
Tab Connector
It is locked in its housing by a spring tab on its side.
Removal is done by squeezing this tab.
A00E1DA
A06E1QA
TAB CONNECTOR
1. Locking tab
To remove:
– Insert a screwdriver or Snap-on TT 600-5 from
opposite side of wire and pry locking tab.
– While holding locking tab pried, pull connector
toward wire side.
11-01-6
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
A01E34A 1
1. Lock
A01E31A
A01E35A
– Pry tab to free connector then pull wire out of
housing. MALE CONNECTOR HOUSING — CUT-AWAY
A00E1GA
2
1. Tab
2. Housing
A01E33A 1
1. Lock
11-01-7
Section 11 WIRING DIAGRAMS
Subsection 01 (WIRING DIAGRAMS)
2
A00E1FA
TYPICAL
1. Receptacle
2. Housing
ACCESSORIES INSTALLATION
On all electric start models: The direct current
(DC) utilizes the snowmobile frame as ground
“wire” while all alternating current (AC) consum-
ers (lights, heated grips, fuel gauge, etc.) utilize a
separate ground wire.
Never interconnect AC and DC grounds as an AC
voltage drop will result. When installing accesso-
ries on any snowmobile, connect their wires di-
rectly to the YELLOW and YELLOW/BLACK light-
ing coil wires.
Even if manual start models have an AC ground
to the chassis (on voltage regulator), all accesso-
ries utilize a ground wire isolated from chassis.
When an electric starter kit is installed, the voltage
regulator and its ground wire are replaced by a
voltage rectifier/regulator unit permitting a com-
pletely isolated AC circuit.
WARNING
Never secure electrical wires/cables with fuel
lines. Keep wires away from any rotating,
moving, heating, vibrating or sharp edge.
Use proper fastening devices as required.
11-01-8
ANNEX 1 TUNDRA R
ANNEX 2 SKANDIC 380/500
FORMULA S
ANNEX 3 MX Z 440
FORMULA DLX 380/500
ANNEX 4 TOURING E/LE/SLE
ANNEX 5 FORMULA 500 LC
TOURING 500 LC
ANNEX 6 FORMULA DLX 500 LC
ANNEX 7 SKANDIC WT/SWT
ANNEX 8 SKANDIC WT LC