Professional Documents
Culture Documents
O W N ER' S MA N UA L
VÄLKOMMEN!
We hope your Volvo will give you many years of happy motoring. The manual. The owner's manual is also available as a mobile app (Volvo
vehicle is designed for the safety and comfort of you and your passen- Manual) and on Volvo Cars support page (support.volvocars.com).
gers. Volvo strives to be one of the world's safest passenger vehicles.
We also encourage everyone to always use seat belts in this and other
Your Volvo is also designed to meet applicable safety and environmental
vehicles. You should also not drive if you are under the influence of alco-
requirements.
hol or medicines or if your ability to drive is for some other reason
To increase your enjoyment of your Volvo, we recommend that you read impaired.
the instructions and maintenance information contained in this owner's
TABLE OF CONTENTS
OWNER'S INFORMATION YOUR VOLVO SAFETY
Owner's information 16 Contacting Volvo 26 Safety 42
Owner's Manual in the center display 17 Volvo ID 26 Safety during pregnancy 43
Navigate in the Owner's Manual in 18 Creating and registering a Volvo ID 27 Occupant safety 43
the center display
Drive-E ‒ purer driving pleasure 27 Reporting safety defects 44
Owner's manual in mobile devices 20
IntelliSafe - driver support 28 Recall information 45
Volvo Cars support site 20
Sensus - connection and entertainment 30 Whiplash Protection System 46
Using the Owner's Manual 21
Software Updates 33 Seat belts 47
The Owner's Manual and the envi- 23
ronment Data recording 33 Buckling and unbuckling seat belts 48
Terms & Conditions for Services 34 Seat belt tensioners 50
Customer Privacy Policy 34 Resetting the electric seat belt ten- 51
sioners
Important information on accessories 35
and extra equipment Door and seat belt reminders 51
Accessory installation 36 Airbags 52
Connecting equipment to the vehi- 36 Driver/passenger-side airbags 53
cle's data link connector
Occupant weight sensor 56
Technician certification 37 Side airbags 60
Viewing the Vehicle Identification 38
Number (VIN) Inflatable curtain 60
Volvo Structural Parts Statement Safety mode 61
38
Driver distraction Starting and moving the vehicle 62
39 when it is in safety mode
Child safety 63
Child restraints 65
Infant seats 67
Convertible seats 69
Booster cushions 71
2
DISPLAYS AND VOICE CONTROL
Top tether anchors 72 Instruments and controls in left-hand 82 Handling the center display 114
drive vehicles
Lower child seat attachment points 74 Activating and deactivating the cen- 117
Instrument panel 84 ter display
ISOFIX/LATCH lower anchors 74
Instrument panel settings 88 Navigating in the center display's views 117
Integrated booster cushion* 76
Fuel gauge 89 Handling tiles in the center display 121
Folding up the integrated booster 77
cushion* Trip computer 89 Function view in the center display 124
Folding down the integrated booster 78 Displaying trip data in the instrument 91 Moving apps and buttons in the cen- 126
cushion* panel ter display
Resetting the trip odometer 92 Symbols in the center display status bar 126
Displaying trip statistics in the center 92 Using the center display keyboard 128
display
Changing keyboard language in the 131
Trip statistics settings 93 center display
Date and time 94 Entering characters, letters and 131
words by hand in the center display
Ambient temperature sensor 94
Changing the appearance of the 133
Indicator symbols in the instrument panel 95 center display
Warning symbols in the instrument panel 97 Turning off and adjusting the volume 133
Instrument panel licenses 98 of the center display system sounds
App menu in instrument panel 104 Changing system units of measurement 134
Handling the App menu in the instru- 105 Changing system language 134
ment panel Opening settings in the center display 134
Messages in the instrument panel 106 Opening contextual setting in the 135
Handling messages in the instru- 107 center display
ment panel Changing settings in the center display 136
Handling messages saved from the 109 Resetting user data when the vehicle 136
instrument panel changes owners
Center display overview 111 Resetting center display settings 137
3
LIGHTING WINDOWS, GLASS AND MIRRORS
Setting types in the center display 137 Lighting panel and controls 154 Windows, glass and mirrors 170
Table of settings in the center display 138 Adjusting light functions via the cen- 155 Pinch protection for windows and 170
ter display sun curtains
Driver profiles 139
Parking lights 156 Reset procedure for pinch protection 171
Selecting a driver profile 140
Daytime running lights 156 Power windows 171
Changing a driver profile's name 141
Low beams 157 Operating the power windows 172
Resetting driver profile settings 141
Using high beam 158 Using sun curtains* 173
Linking a remote key to a driver profile 141
Active high beam 159 Rearview/door mirrors 173
Messages in the center display 142
Using turn signals 160 Adjusting the rearview mirror dim- 174
Handling messages in the center display 143 ming function
Active Bending Lights* 161
Handling messages saved from the 144 Adjusting the door mirrors
center display 175
Front fog lights/cornering illumination* 161
Panoramic roof* 176
Head-up display* 144 Rear fog light 162
Operating the panoramic roof* 177
Activating and deactivating the head- 146 Brake lights 163
up display* Auto closing the panoramic roof* sun 179
Emergency brake lights 163 curtain
Head-up display settings* 146
Hazard warning flashers 164 Using the windshield wipers
Voice control 180
147 Using home safe lighting 164 Heated windshield washer nozzles* 181
Using voice commands 148 Welcome Light 164 Using the rain sensor 181
Voice control for cellular phones 149 Interior Lighting 165 Using the rain sensor's memory function 182
Voice control for radio and media 150 Adjusting interior lighting 167 Using the windshield and headlight 183
Voice control settings 150 washers
Using the rear window wiper/washer 184
Using automatic rear window wiping 185
when backing up
4
SEATS AND STEERING WHEEL CLIMATE CONTROL
Manual front seats 188 Climate 206 Activating and deactivating the 222
heated steering wheel*
Power front seats* 189 Climate zones 206
Activating and deactivating automatic 223
Adjusting the power front seats* 189 Climate control sensors 207 steering wheel heating*
Storing memory settings in power 190 Perceived temperature 207 Activating auto climate control 223
front seats* Climate control system voice commands 208 Activating and deactivating recirculation 224
Using stored memory in a powered 191 Air quality
front seat 209 Activating and deactivating the recir- 224
Clean Zone* 209 culation timer setting
Front seat massage settings* 192
Clean Zone Interior Package* 210 Activating and deactivating max defroster 225
Adjusting front seat massage settings* 192
Interior Air Quality System* 210 Activating and deactivating the 226
Adjusting front seat cushion length 193 heated windshield*
Activating and deactivating the air 211
Adjusting front seat side bolster settings* 194 Activating and deactivating automatic 227
quality sensor*
Adjusting front seat lumbar support* 194 windshield heating*
Passenger compartment air filter 211
Adjusting the passenger seat from 195 Activating and deactivating the 227
Air distribution 212 heated rear window and door mirrors
the driver's seat*
Adjusting air distribution 212 Automatically activating and deacti- 228
Folding the second row backrests 196
Opening, closing and directing air vents vating the heated rear window and
Adjusting the second row head restraints 213 door mirrors
198
Air distribution options 214
Moving the second row seats for- 199 Setting the blower speed for the 228
ward/rearward* Climate system controls 217 front seats
Adjusting the second row backrest tilt 200 Activating and deactivating power 219 Setting the blower speed for the rear 229
front seats* seats*
Getting into and out of the third row 201
of seats* Activating and deactivating the 220 Setting the temperature for the front 230
heated front seat* seats
Folding the third row backrests* 202
Activating and deactivating the 220 Setting the temperature for the rear 231
Steering wheel controls and horn 203 heated rear seats* seats*
Adjusting the steering wheel 203 Activating and deactivating front seat Synchronize temperature 232
221
ventilation* Activating and deactivating air condi- 233
tioning
5
KEY, LOCKS AND ALARM
Activating and deactivating climate 233 Lock indication 236 Locking and unlocking from inside 255
control for the third-row seats* the vehicle
Lock confirmation settings 237
Activating and deactivating auto-start 234 Unlocking the tailgate from inside 257
of third-row climate control* Remote key 237 the vehicle
Locking and unlocking using the 239 Activating and deactivating child 257
remote key safety locks
Settings for remote and inside door 240 Automatic locking when driving 259
unlock
Opening and closing the power tailgate* 259
Unlocking the tailgate using the 241
remote key Setting a maximum height for the 262
power tailgate*
Remote key range 241
Replacing the remote key's battery Foot movement tailgate operation* 263
242
Ordering additional remote keys Private Locking 264
246
Activating and deactivating private 265
Red Key - restricted remote key* 246 locking
Red Key* settings 247 Alarm 266
Detachable key blade 248 Arming and disarming the alarm 267
Locking and unlocking with detacha- 249 Foreign Component Detection*
ble key blade 268
6
DRIVER SUPPORT
Driver support systems 270 Cruise control 284 Starting passing assistance with 302
Adaptive Cruise Control
Speed-dependent steering wheel 270 Activating and starting Cruise Control 285
resistance Limitations of passing assistance 303
Managing Cruise Control speed 286 with Adaptive Cruise Control
Stability system Roll Stability Control 271
Deactivating and putting Cruise Con- 287 Switching target vehicles with Adap- 303
Electronic Stability Control 272 trol in standby mode tive Cruise Control
Electronic Stability Control Sport mode 273 Reactivating Cruise Control from 288 Automatic braking with Adaptive 304
standby mode Cruise Control
Activating/deactivating Sport mode 273
in Electronic Stability Control Switching off Cruise Control 288 Adaptive Cruise Control limitations 305
Electronic Stability Control Sport 274 Distance Alert* 289 Switching between Cruise Control 305
mode limitations and Adaptive Cruise Control
Head-up display for Distance Alert 290
Electronic Stability Control symbols 275 Symbols and messages for Adaptive 307
and messages Activating/deactivating Distance Alert 291
Cruise Control
Speed limiter 276 Setting a time interval for Distance Alert 291
Pilot Assist 309
Activating and starting Speed Limiter 277 Distance Alert limitations 292
Pilot Assist and collision warning 312
Managing Speed Limiter speed 277 Adaptive Cruise Control* 293
Head-up display for Pilot Assist dur- 313
Deactivating and putting Speed Lim- 278 Adaptive Cruise Control and collision 296 ing collision risks
iter in standby mode warning
Activating and starting Pilot Assist 313
Reactivating Speed Limiter from 279 Head-up display for Adaptive Cruise 297
Control with collision warning Managing Pilot Assist speed 314
standby mode
Activating and starting Adaptive 297 Setting a time interval for Pilot Assist 315
Turning off Cruise Control 279
Cruise Control Deactivating/reactivating Pilot Assist 317
Cruise Control limitations 280
Managing Adaptive Cruise Control speed 298 Passing assistance with Pilot Assist 319
Automatic Speed Limiter 280
Setting Adaptive Cruise Control time 299 Starting passing assistance with 319
Activating/deactivating Automatic 282 intervals Pilot Assist
Speed Limiter
Deactivating/reactivating Adaptive 300 Passing assistance with Pilot Assist 319
Changing Automatic Speed Limiter 283 Cruise Control limitations
tolerance
Passing assistance with Adaptive 302 Switching target vehicles with Pilot Assist 320
Automatic Speed Limiter limitations 283 Cruise Control
Automatic braking with Pilot Assist 320
7
Pilot Assist limitations 321 BLIS limitations 348 Selecting guidance to a rest area if 362
the Driver Alert Control warning has
Pilot Assist* symbols and messages 322 Recommended maintenance for BLIS 349 been given
Radar sensor 324 BLIS messages 350 Driver Alert Control limitations 362
Radar sensor limitations 325 Cross Traffic Alert* 351 Lane Keeping Aid 362
Recommended maintenance for the 328 Activating/deactivating Cross Traffic 352 Steering assistance with Lane Keep- 364
radar sensor Alert ing Aid
Radar sensor type approval 328 Cross Traffic Alert limitations 352 Activating/deactivating Lane Keeping Aid 365
Camera 329 Recommended maintenance for 353 Selecting type of assistance for Lane 365
Cross Traffic Alert Keeping Aid
Camera limitations 330
Cross Traffic Alert messages 354 Lane Keeping Aid limitations 365
Recommended maintenance for the 333
camera/radar sensor Road Sign Information* 355 Lane Keeping Aid symbols and mes- 367
City Safety™ 333 Activating/deactivating Road Sign 356 sages
Information Lane Keeping Aid symbols in the 369
City Safety parameters and sub-functions 334
Road Sign Information and sign displays 356 instrument panel
Setting a warning distance for City Safety 336
Road Sign Information and Sensus 357 Steering assistance at risk of collision 370
Detecting obstacles with City Safety 337 Navigation Activating/deactivating steering 370
City Safety in crossing traffic 339 Road Sign Information with Speed 357 assistance during collision risks
Limitations of City Safety in crossing 340 Warning and Settings Run-Off Mitigation with steering 371
traffic Activating/deactivating Speed Warn- 358 assistance
City Safety and delayed evasive 341 ing in Road Sign Information Run-Off Mitigation with steering 371
maneuvers Road Sign Information with speed 359 assistance levels
City Safety limitations 342 camera information Activating/deactivating Run-Off Miti- 372
Road Sign Information limitations 359 gation with steering assistance
City Safety messages 344
Driver Alert Control 360 Limitations of Run-Off Mitigation 372
Rear Collision Warning 345 with steering assistance
Rear Collision Warning limitations 345 Activating/deactivating Driver Alert 361
Control Steering assistance during collision 373
BLIS* 346 risks from oncoming traffic
Activating/deactivating BLIS 347
8
STARTING AND DRIVING
Activating/deactivating Steering 374 Park Assist Camera limitations 389 Starting the vehicle 404
assistance during collision risks with
oncoming vehicles Recommended maintenance of the 391 Switching off the vehicle 406
Park Assist Camera
Limitations of steering assistance 374 Ignition modes 407
during collision risks from oncoming Park Assist Camera symbols and 392
messages Selecting ignition mode 408
traffic
Park Assist Pilot* 393 Brake functions 408
Steering assistance during collision 375
risks from behind* Types of parking with Park Assist Pilot Brakes 409
393
Activating/deactivating Steering 376 Parking with Park Assist Pilot Brake Assist System 410
394
assistance during collision risks from Braking on wet roads
Leaving a parking space with Park 397 410
behind*
Assist Pilot Braking on salted roads 411
Limitations of steering assistance 376
during collision risks from behind Park Assist Pilot* limitations 398 Maintenance of the brake system 411
Symbols and messages for steering 378 Recommended maintenance for 400 Parking brake 411
assistance during collision risks Park Assist Pilot
Activating and deactivating the park- 412
Park Assist* 379 Park Assist Pilot* messages 401 ing brake
Park Assist front, rear and sides 380 Settings for automatically activating 413
the parking brake
Activating/deactivating Park Assist 381
Parking on a hill 414
Park Assist limitations 381
Parking brake malfunction 414
Recommended maintenance for 382
Park Assist Auto-hold brakes 415
Park Assist symbols and messages 383 Activating and deactivating Auto- 416
hold at a standstill
Park Assist Camera* 384
Hill Start Assist 416
Park Assist Camera views 385
Braking assist after a collision 417
Park Assist Camera trajectory lines 386
Transmission 417
Sensor field from Park Assist for 388
Park Assist Camera Gear selector positions for automatic 418
transmissions
Starting the Park Assist Camera 389
9
Using the steering wheel paddles* to 419 Economical driving 438 Activating and deactivating the compass 460
shift
Preparing for a long trip 439 Calibrating the compass 460
Shiftlock 421 Winter driving 440
Deactivating the automatic shiftlock 421 Driving through standing water 441
The kickdown function 422 Opening/closing the fuel filler door 441
Gear indicator* 422 Refueling 442
All Wheel Drive (AWD)* 423 Fuel 442
Drive modes* 423 Octane rating 443
Changing drive mode* 425 Emission controls 445
ECO drive mode 426 Overheating of engine and transmission 446
Activating and deactivating ECO 428 Battery drain
drive mode using the function button 447
Jump starting using another battery 447
Start/Stop function 428
Detachable towbar* 448
Driving with the Start/Stop function 428
Driving with a trailer 449
Temporarily deactivating the Start/ 430
Stop function Trailer Stability Assist* 451
Conditions for the Start/Stop function 430 Checking trailer lights 452
Leveling control* and suspension 432 Towing using a towline 453
Leveling control settings* 435 Attaching and removing the towing eyelet 454
Low Speed Control* 435 Recovery 455
Activating and deactivating Low 436 HomeLink®* 456
Speed Control* using the function button
Programming HomeLink®* 457
Hill Descent Control* 437
Using HomeLink 458
Activating and deactivating Hill 438
Descent Control* using the function Type approval for HomeLink®* 459
button Compass 459
10
AUDIO, MEDIA AND INTERNET
Audio, media and Internet 464 SiriusXM Travel Link®* - Fuel 483 Tips for using Android Auto* 498
Sound settings 464 SiriusXM Travel Link®* - Sports 484 Phone 498
Apps 465 Media player 485 Connecting a phone to the car via 499
Bluetooth for the first time
Download apps 466 Playing media 486
Connecting a phone to the car via 501
Updating apps 467 Controlling and changing media 487 Bluetooth automatically
Deleting apps 468 Media searches 488 Connecting a phone to the car via 501
Radio 468 Bluetooth manually
Gracenote® 489
Starting the radio 469 Disconnecting a Bluetooth-con- 502
CD player* 489 nected phone
Changing waveband and radio station 469 Video 490 Switch between phones connected 502
Searching for a radio station 470 Playing video via Bluetooth
490
Storing radio favorites 471 Removing a Bluetooth-connected phone 503
Playing DivX® 490
Radio settings 471 Handling phone calls 503
Video settings 491
RBDS 472 Handling text messages 504
Streaming media via Bluetooth® 491
HD Radio™ 472 Text message settings 505
Connecting a device via Bluetooth® 491
Activating and deactivating the HD 474 Managing the phone book 505
Radio™ Playing media via the USB port 492
Phone settings 506
HD Radio™ sub-channels 474 Connecting a device via the USB port 492
Settings for Bluetooth devices 507
HD Radio™ limitations 475 Apple® CarPlay®* 493
Internet-connected vehicle* 507
SiriusXM® Satellite radio* 476 Using Apple® CarPlay®* 493
Connecting the car to the Internet 509
Using SiriusXM® Satellite radio* 477 Settings for Apple® CarPlay®* 494 via a mobile device (Bluetooth)
Settings for SiriusXM® Satellite radio* 478 Tips for using Apple® CarPlay®* 495 Connecting the car to the Internet 509
via a mobile device (Wi-Fi)
SiriusXM Travel Link®* 480 Android Auto* 496
Connect the car to the Internet via 510
SiriusXM Travel Link®* - Weather 481 Using Android Auto* 496 car modem (SIM card)
SiriusXM Travel Link®* - Notifications 482 Settings for Android Auto* 497 Vehicle modem settings 511
11
WHEELS AND TIRES
Sharing Internet from the vehicle via 511 Tires 528 Tire sealing system 550
Wi-Fi hotspot (tethering)
Tire direction of rotation 530 Using the tire sealing system 551
No or poor Internet connection 512
Tread wear indicator 531 Inflate tires with the compressor 555
Deleting Wi-Fi networks 513 included in the tire sealing system
Tire terminology 531
Wi-Fi technology and security 513 Determining the vehicle's permitted 556
Tire sidewall designations 532 weight
Terms of use and data sharing 514
Uniform Tire Quality Grading 534
Activating and deactivating data sharing 514
Checking tire pressure 535
Compatible file formats for media 514
Adjusting tire pressure 536
Technical specifications for USB devices 515
Recommended tire pressure 537
Hard disk storage space 516
Tire pressure monitoring system* 537
License agreement for audio and media 517
Calibrating the tire pressure monitor- 539
ing system*
Viewing tire pressure status in the 540
center display*
Action when warned of low tire pressure 541
When changing wheels 542
Tool kit 542
Jack* 543
Wheel bolts 543
Removing a wheel 544
Installing a wheel 546
Spare wheel 547
Accessing the spare wheel 548
Snow tires 549
Snow chains 549
12
LOADING, STORAGE AND MAINTENANCE AND SERVICE
PASSENGER COMPARTMENT Volvo's service program 576 Replacing the high beam headlight bulbs 595
Passenger compartment interior 558 Data transfer between vehicle and 578 Replacing daytime running lights/ 596
Tunnel console 559 workshop over Wi-Fi front parking light bulbs
Electrical outlets 560 Download Center 579 Replacing front turn signal bulbs 597
Using the electrical outlets 562 Handling system updates via Down- 579 Bulb specifications 597
load Center
Using the glove compartment 563 Start battery 598
Vehicle status 580
Sun visors 564 Support battery 601
Scheduling service and repairs 580
Cargo compartment 564 Battery symbols 602
Sending vehicle information to the 582
Loading recommendations 564 workshop Fuses and fuseboxes 603
Roof loads and load carriers 566 Hoisting the vehicle 583 Replacing fuses 604
Grocery bag holders 566 Opening and closing the hood 585 Fuses in the engine compartment 605
Load anchoring eyelets 567 Climate control system service 586 Fuses under the glove compartment 608
Installing and removing the cargo 567 Replacing a windshield with head-up 586 Fuses in the cargo compartment 611
compartment cover* display* Cleaning the interior 615
Operating the cargo compartment cover* 568 Engine compartment overview 587 Cleaning the center display 615
Installing and removing the steel 570 Engine oil 587 Cleaning the head-up display* 616
cargo grid*
Checking and filling engine oil 588 Cleaning fabric upholstery and ceil- 617
Installing and removing the cargo net* 571 Refilling coolant ing liner
590
Replacing bulbs 591 Cleaning the seat belt 617
Removing the plastic cover to 593 Cleaning floor mats and inlay mats 617
replace bulbs Cleaning leather upholstery 618
Removing the rectangular headlight 593 Cleaning the leather steering wheel 619
cover
Cleaning interior plastic, metal and 620
Location of exterior lights 594 wood surfaces
Replacing the low beam headlight bulbs 595 Cleaning the exterior 620
13
SPECIFICATIONS INDEX
Polishing and waxing 621 Type designations 636 Index 649
Hand washing 621 Dimensions 639
Automatic car washes 623 Weights 641
High-pressure washing 624 Towing capacity and tongue weight 642
Cleaning the wiper blades 624 Engine specifications 643
Cleaning exterior plastic, rubber and 625 Engine oil specifications 644
trim components
Coolant specifications 645
Cleaning rims 626
Transmission fluid specifications 645
Corrosion protection 626
Brake fluid specifications 645
Paintwork 627
Fuel tank volume 646
Touching up minor paint damage 627
Air conditioning specifications 646
Color codes 628
Approved tire pressure 647
Changing rear window wipers 629
Replacing windshield wiper blades 630
Windshield wipers in the service position 631
Filling washer fluid 632
14
OWNER'S INFORMATION
OWNER'S INFORMATION
1 For markets without Owner's Manuals in the center display, a complete printed manual is provided along with the vehicle.
16
OWNER'S INFORMATION
CAUTION Owner's Manual in the center The information in the Owner's Manual can be
display accessed directly via the Owner's Manual start
The driver is always responsible for operating page or via its Top menu.
A digital version of the Owner's Manual is availa-
the vehicle in a safe manner and adhering to
ble in the vehicle's center display2. Contextual Owner's Manual
all applicable laws and regulations. It is also
important that the vehicle is operated, main- The digital Owner's Manual can be accessed
tained and serviced according to Volvo's rec- from Top view and in certain cases, the contex-
ommendations provided in the owner's infor- tual Owner's Manual can also be accessed from
mation. Top view.
NOTE
OWNER'S MANUAL
Changing languages in the center display
could mean that certain owner's information The contextual Owner's Manual is accessed from Top
will not comply with national or local laws and view.
regulations. Do not change to a language that
When a contextual Owner's Manual is available, it
you do not fully understand, as this could
will be shown to the right of Owner's manual in
make it difficult to navigate back through the
Top view.
menu.
Tap the contextual Owner's Manual to open an
article in the Owner's Manual related to the infor-
Related information
mation displayed on the screen. For example, tap
• Owner's Manual in the center display
Navigation Manual to open an article related to
(p. 17)
navigation.
• Owner's manual in mobile devices (p. 20)
The Owner's Manual is accessed from Top view. Certain apps in the vehicle only. For third-party
• Volvo Cars support site (p. 20) apps that have been downloaded, it is not possi-
To open the Owner's Manual, pull down Top view
• Using the Owner's Manual (p. 21) in the center display and tap Owner's manual. ble to e.g. access app-specific articles.
17
OWNER'S INFORMATION
|| Related information Navigate in the Owner's Manual in Opening the menu in the Top menu
• Navigate in the Owner's Manual in the center the center display – Tap in the upper list in the Owner's
display (p. 18) The digital Owner's Manual can be accessed Manual.
• Navigating in the center display's views from the center display's Top view. The contents > A menu will open, displaying different
(p. 117) are searchable and it is easy to navigate among options for finding information:
the various sections.
• Download apps (p. 466) Start page
Tap the symbol to return to the
Owner's Manual start page.
Categories
The articles in the Owner's
Manual are structured into
main and sub-categories. The
same article may appear in sev-
eral relevant categories in order
The Owner's Manual is accessed from Top view.
to make them easier to find.
– To open the Owner's Manual, pull down Top
view in the center display and tap Owner's 1. Tap Categories.
manual. > The main categories are listed.
There are a number of ways to find information in 2. Tap a main category ( ).
the Owner's Manual. The options can be
> A list of sub-categories ( ) and articles
accessed from the Owner's Manual start page
and from the Top menu. ( ) will appear.
3. Tap an article to open it.
To go back, tap the left arrow.
18
OWNER'S INFORMATION
19
OWNER'S INFORMATION
Owner's manual in mobile devices can easily navigate between sections in the Volvo Cars support site
The Owner's Manual is available as a mobile Owner's Manual and the contents are searchable. Volvo Cars' website and support site contain
app3 and can be downloaded from the App additional information about your vehicle.
Store and Google Play. The app is adapted for
both smartphones and tablets. Online support
Go to support.volvocars.com to visit the site. The
support site is available in most markets.
The site contains support for e.g. Internet-based
services and functions, Volvo On Call, the naviga-
tion system* and apps. Videos and step-by-step
instructions explain various procedures, such as
how to connect the vehicle to the Internet via a
cellular phone.
Downloadable information
Maps
For vehicles equipped with Sensus Navigation,
maps can be downloaded from the support site.
The Owner's Manual can be Mobile apps
downloaded as a mobile app Beginning with model year 2014, the Owner's
from the App Store or Google Manual is available as an app for certain Volvo
Play. This QR code will take The mobile app is available on both App Store and Goo-
gle Play. models. The Volvo On Call app can also be down-
you directly to the app. You can loaded from the support site.
also search for "Volvo manual" Related information
in the App Store or Google Owner's manuals in PDF format
• Using the Owner's Manual (p. 21)
Owner's Manuals are available for downloading in
Play.
PDF format. Select the vehicle model and year to
The app contains videos and exterior/interior download the desired manual.
images of the vehicle. These images contain hot-
spots for various functions, components, etc.,
which lead directly to related information. You
20 * Option/accessory.
OWNER'S INFORMATION
}}
* Option/accessory. 21
OWNER'S INFORMATION
Procedures
White ISO symbols and white text/image on a Procedures that must be carried out in a certain
black or blue warning field and message field. order are shown as numbered lists in the
Used to indicate potential danger. Ignoring a Owner's Manual.
warning of this type could result in damage.
When a series of illustrations are provided
Information along with the step-by-step instructions, the
numbers of the steps correspond with the
Black ISO symbols on a yellow warning field, numbers of the illustrations.
white text/image on a black message field. Used Lists using letters instead of numbers are
to indicate potential danger. Ignoring a warning of used in cases where the order in which the
this type could result in serious injury or death. instructions are carried out is not important.
Arrows with or without numbers are used to
indicate the direction of movement.
Arrows with letters are used to indicate a
movement in cases where the order in which
the instructions are carried out is not impor-
tant.
22
OWNER'S INFORMATION
If there are no illustrations associated with step- Continues on next page The Owner's Manual and the
by-step instructions, the steps are indicated by }} This symbol is shown in the lower right-hand environment
ordinary numbers. corner to indicate that the current topic continues The Owner's Manual is printed on paper from
on the next page. responsibly managed forests.
Position lists
Red circles containing a number are used in Continuation from previous page The Forest Stewardship Council (FSC)® symbol
general overview illustrations of components. || This symbol is shown in the upper left-hand certifies that the paper pulp in the printed
The corresponding number is used in the corner to indicate that the current topic is a con- Owner's Manual comes from FSC®-certified for-
position list's description of that component. tinuation from the previous page. ests or other responsibly managed sources.
Bullet lists Related information
Bullets are used for items (components, func- • Owner's Manual in the center display (p. 17)
tions, information, etc.) that can be listed in a ran-
dom order. • Owner's manual in mobile devices (p. 20)
• Volvo Cars support site (p. 20)
For example:
• Coolant
• Engine oil
Related information
Related information offers references to other Related information
parts of the manual containing information asso- • Drive-E ‒ purer driving pleasure (p. 27)
ciated with the information you are currently
reading.
Images
Illustrations and images used in the Owner's
Manual are sometimes generic and are intended
to provide an overview or an example of a certain
function or feature. These images vary depending
on equipment level and market and may differ
from the appearance of your vehicle.
23
YOUR VOLVO
YOUR VOLVO
1 The services available may vary over time and depending on equipment level and market.
2 For Volvo On Call users.
26
YOUR VOLVO
Creating and registering a Volvo ID Registering your Volvo ID to the vehicle Drive-E ‒ purer driving pleasure
A Volvo ID can be created in two ways. If your If your Volvo ID was created using the Volvo On Volvo is committed to the well-being of its cus-
Volvo ID was created with the Volvo On Call Call app, follow these steps to register the ID to tomers. As a natural part of this commitment, we
app, the Volvo IDmust also be registered to the the vehicle: care about the environment in which we all live.
vehicle to enable access to the Volvo ID serv- 1. If you have not already done so, download Concern for the environment means an everyday
ices. the Volvo ID app from Download Center in involvement in reducing our environmental
Creating a Volvo ID using the app App view. impact.
1. Download the Volvo ID app from Download Volvo's environmental activities are based on a
holistic view, which means we consider the over-
Center in the center display's App view. NOTE all environmental impact of a product throughout
2. Start the app and register a personal email To download apps the vehicle must be con- its complete life cycle. In this context, design, pro-
address. nected to the internet. duction, product use, and recycling are all impor-
3. Follow the instructions that will be sent auto- tant considerations. In production, Volvo has
matically to this email address. 2. Start the app and enter your Volvo ID/email partly or completely phased out several chemicals
address. including CFCs, lead chromates, asbestos, and
> A Volvo ID has now been created and is
cadmium; and reduced the number of chemicals
automatically registered to the vehicle. 3. Follow the instructions that will be automati- used in our plants 50% since 1991.
The Volvo ID services can now be used. cally sent to the email address connected to
your Volvo ID. Volvo was the first in the world to introduce into
Creating a Volvo ID using the Volvo On Call
production a three-way catalytic converter with a
app3 > Your Volvo ID has now been registered to
Lambda sond, now called the heated oxygen sen-
1. Download the latest version of the Volvo On the vehicle. The Volvo ID services can now
sor, in 1976. The current version of this highly
Call app from a smartphone, via e.g. App be used.
efficient system reduces emissions of harmful
Store, Windows Phone or Google Play. substances (CO, HC, NOx) from the exhaust pipe
Related information
2. On the app's start page, create a Volvo ID • Volvo ID (p. 26) by approximately 95 - 99% and the search to
and enter a personal email address. eliminate the remaining emissions continues.
• Download apps (p. 466) Volvo is the only automobile manufacturer to
3. Follow the instructions that will be sent auto-
• Handling system updates via Download Cen- offer CFC-free retrofit kits for the air conditioning
matically to this email address. ter (p. 579) system of all models as far back as the 1975
> A Volvo ID has now been created. See model 240. Advanced electronic engine controls
below for information on how the ID is
• Internet-connected vehicle* (p. 507)
and cleaner fuels are bringing us closer to our
registered to the vehicle.
* Option/accessory. 27
YOUR VOLVO
28 * Option/accessory.
YOUR VOLVO
possible collision and help the driver act in time • Airbags (p. 52)
to prevent it. If the driver does not react to the • Whiplash Protection System (p. 46)
warning and the risk of collision is determined to
be imminent, City Safety can automatically apply
the brakes.
Lane assistance (LKA) is another example of a
function that can help prevent accidents by help-
ing the driver - on expressways and similar larger
roads - to reduce the risk of the car accidentally
leaving its own lane.
The function Steering aid during increased
collision risk can help the driver reduce the risk
of the car leaving its lane unintentionally and/or
colliding with another vehicle or obstacle by
actively steering the car back into its lane and/or
swerving.
Protection
To help protect the driver and passengers, the
vehicle is equipped with seat belt tensioners that
pull the seat belts taut in collisions and other crit-
ical situations. The vehicle also has airbags, inflat-
able curtains and the Whiplash Protection
System (WHIPS), which helps prevent whiplash
injuries.
Related information
• Driver support systems (p. 270)
• Active high beam (p. 159)
• Safety (p. 42)
• Seat belts (p. 47)
29
YOUR VOLVO
This is Sensus
30 * Option/accessory.
YOUR VOLVO
Different types of information are shown in different displays depending on how the information should be prioritized.
Head-up display* and navigation messages*. Road sign information Instrument panel
and incoming phone calls are also shown in the
head-up display. These can be handled using the
right-side steering wheel keypad or the center
display.
* Option/accessory. 31
YOUR VOLVO
Related information
• Head-up display* (p. 144)
• Instrument panel (p. 84)
• Center display overview (p. 111)
• Voice control (p. 147)
• Internet-connected vehicle* (p. 507)
• Sharing Internet from the vehicle via Wi-Fi
hotspot (tethering) (p. 511)
32 * Option/accessory.
YOUR VOLVO
Software Updates Data recording as law enforcement, could combine the EDR data
So that you as a Volvo customer shall have the As part of Volvo's commitment to safety and with the type of personally identifying data rou-
best possible experience from your car, Volvo is quality, certain information is recorded regarding tinely acquired during a crash investigation. To
continuously developing the systems in the cars vehicle operation, functionality and incidents. read data recorded by an EDR, special equipment
and the services that you are offered. is required, and access to the vehicle or the EDR
This vehicle is equipped with an event data is needed.
You can update the software in your Volvo to the recorder (EDR). The main purpose of an EDR is
Furthermore, your vehicle is equipped with a
latest version when your car is serviced at an to record, in certain crash or near crash-like sit-
number of computers whose task is to continu-
authorized Volvo dealer. The latest software uations, such as an airbag deployment or hitting
ously control and monitor the vehicle's operation.
update gives you access to new functions and a road obstacle, data that will assist in under-
They can also register some of this information
improvements, as well as previous improvements standing how a vehicle's systems performed. The
during normal driving conditions, most importantly
included with previous software updates. EDR is designed to record data related to vehicle
if they detect a fault relating to the vehicle's
dynamics and safety systems for a short period of
For more information about released updates and operation and functionality or upon activation of
time, typically 30 seconds or less. The EDR in
answers to frequently asked questions, please go the vehicle's active safety systems (e.g. City
this vehicle is designed to record such data as:
to support.volvocars.com. Safety and the auto-brake function). Some of the
• How various systems in your vehicle were registered information is required by technicians
NOTE operating; when carrying out service and maintenance to
• Whether or not the driver and passenger enable them to diagnose and rectify any faults
Functionality after updating may vary depend- that have occurred in the vehicle and to enable
ing on market, model, model year and options. safety belts were buckled/fastened;
Volvo to fulfill legal and other regulatory require-
• How far (if at all) the driver was depressing
ments. Information thus registered in the vehicle
the accelerator and/or brake pedal; and,
Related information is registered in the vehicle's computers until the
• Sensus - connection and entertainment • How fast the vehicle was traveling. vehicle is serviced or repaired. In addition to the
(p. 30) These data can help provide a better understand- above, the registered information may - on an
ing of the circumstances in which crashes and aggregated basis - be used for research and
• Handling system updates via Download Cen-
ter (p. 579) injuries occur. product development purposes in order to contin-
uously improve the safety and quality of Volvo
EDR data is only recorded by the vehicle if a vehicles.
more serious collision situation occurs. No data is
recorded by the EDR under normal driving condi- For additional information, please contact Volvo.
tions and the EDR never registers who is driving
the vehicle or the location of a crash or a near
crash-like situation. However, other parties, such
}}
33
YOUR VOLVO
|| Related information Terms & Conditions for Services Customer Privacy Policy
• Contacting Volvo (p. 26) Volvo offers services to help make driving your Volvo respects and safeguards the personal pri-
• Volvo Structural Parts Statement (p. 38) Volvo as safe and comfortable as possible. vacy of everyone who visits our websites.
These services comprise everything from assis- This policy refers to the handling of customer
tance in emergencies to navigation and various data and personal information. The purpose is to
maintenance services. give current, past and potential customers a gen-
eral understanding of:
Before using the services, it is important to read
the Terms and Conditions for the services at • The circumstances in which we collect and
support.volvocars.com. process your personal data.
Related information
• Terms of use and data sharing (p. 514)
• Terms & Conditions for Services (p. 34)
• Data recording (p. 33)
34
YOUR VOLVO
35
YOUR VOLVO
Accessory installation that may result from the installation of non- Connecting equipment to the
We strongly recommend that Volvo owners use genuine accessories. vehicle's data link connector
only genuine, Volvo-approved accessories, and Incorrectly connected or installed software or
Related information
that accessory installations be performed only by diagnostic tools may have an adverse effect on
a trained and qualified Volvo service technician. • Important information on accessories and
the vehicle's electronics.
extra equipment (p. 35)
Certain accessories only work when the associ- We strongly recommend that Volvo owners use
ated software is installed in the vehicle's com- only genuine, Volvo-approved accessories, and
puter system. that accessory installations be performed only by
a trained and qualified Volvo service technician.
• Genuine Volvo accessories are tested to Certain accessories only work when the associ-
ensure compatibility with the performance, ated software is installed in the vehicle's com-
safety, and emission systems in your vehicle. puter system.
Additionally, a trained and qualified Volvo
service technician knows where accessories
may and may not be safely installed in your
Volvo. In all cases, please consult a trained
and qualified Volvo service technician before
installing any accessory in or on your vehicle.
• Accessories that have not been approved by
Volvo may or may not be specifically tested
for compatibility with your vehicle.
• Any of your vehicle's performance and safety
systems could be adversely affected if you
install accessories that Volvo has not tested,
or if you allow accessories to be installed by On-board Diagnostic (OBDII) socket under the dash-
someone unfamiliar with your vehicle. board on the driver's side.
• Damage caused by unapproved or improperly
installed accessories may not be covered by
your new vehicle warranty. See your Warranty
and Service Records Information booklet for
more warranty information. Volvo assumes no
responsibility for death, injury, or expenses
36
YOUR VOLVO
WARNING
Changes or modifications not expressively
approved by the party responsible for compli-
ance could void the user's authority to oper-
ate the equipment.
Canada
IC: 20839-ACUII06
37
YOUR VOLVO
Viewing the Vehicle Identification Volvo Structural Parts Statement In addition Volvo does not support the use or re-
Number (VIN) Volvo is one of the leading companies for car use of structural components from an existing
When contacting a Volvo retailer, about e.g. your safety. vehicle that has been previously damaged.
Volvo On Call subscription, your Vehicle Identifi- Although these parts may appear equivalent, it is
Volvo engineers and manufactures vehicles difficult to tell if the parts have been previously
cation Number (VIN5) may be needed.
designed to help protect vehicle occupants in the replaced with non-OE parts or if the part has
1. Tap Settings in the Top view in the center
event of a collision. been damaged as a result of a prior collision. The
display.
Volvos are designed to absorb the impact of a quality of these used parts may also have been
2. Proceed to System System Information collision. This energy absorption system including, affected due to environmental exposure.
Vehicle Identification Number. but not limited to, structural components such as Related information
> The vehicle identification number will be bumper reinforcement bars, bumper energy
absorbers, frames, rails, fender aprons, A-pillars,
• Data recording (p. 33)
displayed.
B-pillars and body panels must work together to
maintain cabin integrity and protect the vehicle
occupants.
The supplemental restraint system including but
not limited to air bags, side curtain air bags, and
deployment sensors work together with the
above components to provide proper timing for
air bag deployment.
Due to the above, Volvo Car USA does not sup-
port the use of aftermarket, alternative or any-
thing other than original Volvo parts for collision
repair.
Volvo Car USA also recommends using Volvo-
approved replacement glass. The use of after-
market glass, particularly a windshield, can have
an adverse effect on collision avoidance and
advanced lighting systems.
38
YOUR VOLVO
39
SAFETY
SAFETY
42
SAFETY
Safety during pregnancy the vehicle (which means they should be able to Occupant safety
It is important that seat belts are worn correctly easily reach the steering wheel and foot pedals). Safety is Volvo's cornerstone.
during pregnancy and that pregnant drivers Try to maintain as much distance as possible
adjust their seating position accordingly. between the stomach and the steering wheel. Volvo's concern for safety
Our concern for safety dates back to 1927 when
Seat belt Related information the first Volvo rolled off the production line.
• Safety (p. 42) Three-point seat belts (a Volvo invention), safety
• Seat belts (p. 47) cages, and energy-absorbing impact zones were
designed into Volvo vehicles long before it was
• Manual front seats (p. 188)
fashionable or required by government regulation.
• Power front seats* (p. 189)
We will not compromise our commitment to
safety. We continue to seek out new safety fea-
tures and to refine those already in our vehicles.
You can help. We would appreciate hearing your
suggestions about improving automobile safety.
We also want to know if you ever have a safety
concern with your vehicle. Call us in the U.S. at:
1-800-458-1552 or in Canada at:
The seat belt should fit closely against the shoul- 1-800-663-8255.
der, with the diagonal section between the
breasts and to the side of the stomach.
The lap section of the seat belt should lie flat
over the thighs and as far as possible under the
stomach. Never let it ride upward. Remove
unnecessary slack and make sure the seat belt
fits as close as possible to the body. Make sure
there are no twists in the seat belt.
Seating position
As pregnancy progresses, pregnant drivers
should adjust the seat and steering wheel to a
position that allows them to retain full control of
}}
* Option/accessory. 43
SAFETY
44
SAFETY
You can also obtain other information Transport Canada can be contacted at: Recall information
about motor vehicle safety from http:// 1-800-333-0510
On our website, select the "Own" tab on the
www.safercar.gov, where you can also Teletypewriter (TTY): 613 990-4500 upper left side of the screen and click the head-
enter your vehicle's VIN (Vehicle Identi- Fax: 1-819-994-3372 ing "Recall Information" on the right side of the
fication Number) to see if it has any Mailing Address: Transport Canada - Road
screen. Enter your Vehicle Identification Number
open recalls. (VIN) for your vehicle (found at the base of the
Safety, 80 rue Noël, Gatineau, (Quebec) J8Z 0A1
windshield). If your vehicle has any open Recalls,
Volvo strongly recommends that if your Related information they will be displayed on this page.
vehicle is covered under a service cam- • Safety (p. 42) You can also enter the Vehicle Identification
paign, safety or emission recall or simi- • Occupant safety (p. 43) Number in the search field on the National
lar action, it should be completed as • Recall information (p. 45)
Highway Traffic Safety Administration's (NHTSA)
soon as possible. Please check with website at: www.nhtsa.gov.
• Viewing the Vehicle Identification Number
your local retailer or Volvo Car USA, (VIN) (p. 38) Volvo customers in Canada
LLC if your vehicle is covered under For any questions regarding open recalls for your
these conditions. vehicle, please contact your authorized Volvo
retailer. If your retailer is unable to answer your
NHTSA can be reached at: questions, please contact Volvo Customer Rela-
tions at 800-663-8255, Monday through Friday,
Internet: 8:30 A.M. to 5:00 P.M. EST or volvocars.com/ca.
http://www.nhtsa.gov You may also write us at:
Volvo Car Canada Ltd.
Telephone:
Customer Care Centre
1-888-DASH-2-DOT
9130 Leslie Street, Suite 101
(1-888-327-4236).
Richmond Hill, Ontario L4B 0B9
Reporting safety defects in Canada
www.tc.gc.ca
If you believe your vehicle has a defect that could
cause a crash or could cause injury or death, you
should immediately inform Transport Canada in
addition to notifying Volvo Car Canada Ltd.
}}
45
SAFETY
WARNING
WHIPS is a supplement to the seat belt.
Always wear your seat belt.
Do not place any objects on the floor behind or under
the front seats or on the rear seat that could prevent
WHIPS from functioning correctly.
46
SAFETY
Seating position
For WHIPS to provide optimal protection, the
driver and passenger must be seated correctly
and the system's function must not be impeded
in any way.
Set the front seat to the correct seating position
before starting to drive.
The driver and the front seat passenger should
sit in the center of the seat with their heads as
close as possible to the head restraints.
Related information
• Safety (p. 42)
• Manual front seats (p. 188)
• Power front seats* (p. 189)
}}
* Option/accessory. 47
SAFETY
48
SAFETY
2. Buckle the seat belt by pushing the latch 3. The height of the seat belts in the front seats
plate into the receptacle. and outboard rear seating positions can be
> A distinct "click" indicates that the belt is adjusted.
locked into place.
WARNING
Always insert the seat belt latch plate into the
belt buckle on the correct side. Failure to do
so could cause the seat belts and belt buck-
les to malfunction in a collision. There is a risk
of serious injury.
49
SAFETY
|| WARNING 2. If it does not fully retract, guide the belt man- Seat belt tensioners
ually into the slot and make sure it does not The vehicle is equipped with standard and elec-
Never use a seat belt for more than one hang loose.
occupant. Never wear the shoulder portion of tric seat belt tensioners that can help tension the
the belt under the arm, behind the back or If the seat belt in the second row center seat belt in a critical situation or collision.
otherwise out of position. Such use could seating position is used, make sure it is prop-
cause injury in the event of an accident. As erly positioned in the correct seat belt guide.
Standard seat belt tensioners
seat belts lose much of their strength when All seat belts are equipped with a standard seat
exposed to violent stretching, they should be Related information belt tensioner.
replaced after any collision, even if they • Seat belts (p. 47)
appear to be undamaged. In a collision of sufficiently violent force, the seat
• Seat belt tensioners (p. 50) belt tensioners will tension the seat belts in order
to more effectively restrain the occupants.
• Door and seat belt reminders (p. 51)
WARNING
Electric seat belt tensioners
Do not use clips or fasten the belts around
The driver's and front passenger's seat belts are
hooks or other parts of the interior. This will
prevent the seat belt from fitting properly. equipped with electric seat belt tensioners.
The seat belt tensioners interact and can be acti-
vated in conjunction with the City Safety and
WARNING Rear Collision Warning driver support systems. In
Never damage the seat belts and never insert critical situations, such as if the vehicle brakes
any foreign objects into the belt buckle. This suddenly, begins to skid or runs off the road (e.g
may cause the seat belts and belt buckles to if the vehicle rolls into a ditch, lifts off the ground
malfunction in a collision. There is a risk of
serious injury. or hits an obstacle in the road), or if there is a risk
of collision, the seat belts can be pulled taut by
the seat belt tensioner's electric motor.
Unbuckling seat belts
1. Press the red button on the seat belt recep- The electric seat belt tensioner helps to position
tacle and make sure the seat belt retracts the occupant more effectively in the seat, which
fully into the retractor slot. reduces the risk of the occupant striking the inte-
rior of the passenger compartment and improves
the effect of other safety systems such as the
airbags.
50
SAFETY
When a critical situation has passed, the seat belt Resetting the electric seat belt Door and seat belt reminders
and the electric seat belt tensioner are reset tensioners This system is intended to remind occupants to
automatically. However, they can also be reset The electric seat belt tensioners are designed to buckle their seat belts and to alert the driver if a
manually. be reset automatically, but if the seat belt door or the hood, tailgate or fuel filler door is
remains taut it can be reset manually. open.
WARNING 1. Stop the vehicle in a safe location.
Graphics in the instrument panel
Never attempt to alter or repair the seat belt 2. Unbuckle the seat belt and then rebuckle it.
on your own. Volvo recommends contacting
> The seat belt and the electric seat belt
an authorized Volvo workshop.
tensioner will be reset.
If the seat belt has been exposed to extreme
forces, e.g. in conjunction with a collision, the
entire seat belt must be replaced. Even if the WARNING
seat belt appears undamaged, some of its Never attempt to alter or repair the seat belt
protective properties may have been lost. Also on your own. Volvo recommends contacting
replace the seat belt if it is worn or damaged. an authorized Volvo workshop.
The new seat belt must be type approved and
intended for the same seating position as the If the seat belt has been exposed to extreme
replaced seat belt. forces, e.g. in conjunction with a collision, the
entire seat belt must be replaced. Even if the
seat belt appears undamaged, some of its
Related information protective properties may have been lost. Also Graphics in the instrument panel with various types of
• Seat belts (p. 47) replace the seat belt if it is worn or damaged. warnings. The warning colors for the doors/tailgate vary
The new seat belt must be type approved and depending on the vehicle's speed.
• Buckling and unbuckling seat belts (p. 48) intended for the same seating position as the The instrument panel graphic shows the seats
• Resetting the electric seat belt tensioners replaced seat belt.
where seat belts are buckled and not buckled.
(p. 51)
The same graphic also indicates if the hood, tail-
• City Safety™ (p. 333) Related information
gate, fuel filler door or any door is open.
• Rear Collision Warning (p. 345) • Seat belt tensioners (p. 50)
• Seat belts (p. 47) Confirm the graphic by briefly pressing the O
button on the right-side steering wheel keypad.
}}
51
SAFETY
52
SAFETY
53
SAFETY
|| sors that activate the gas generators, causing the WARNING certain non-frontal collisions where rapid
airbags to be inflated with nitrogen gas. deceleration occurs.
• The airbags in the vehicle are designed to
As the movement of the seats' occupants com- be a SUPPLEMENT to-not a replacement • The airbag system sensors, which trigger the
presses the airbags, some of the gas is expelled front airbags, are designed to react to both
for-the three-point seat belts. For maxi-
at a controlled rate to provide better cushioning. the impact of the collision and the inertial
mum protection, wear seat belts at all
Both seat belt tensioners also deploy, minimizing forces generated by it, and to determine if
times. Be aware that no system can pre-
seat belt slack. The entire process, from inflation the intensity of the collision is sufficient for
vent all possible injuries that may occur in
to deflation of the airbag, occurs within tenths of the seat belt tensioners and/or airbags to be
an accident.
a second. deployed.
• Never drive with your hands on the steer-
However, not all frontal collisions activate the
The location of the front airbags is indicated by ing wheel pad/airbag housing.
SRS AIRBAG embossed on the steering wheel front airbags.
pad and above the glove compartment, and by • The front airbags are designed to help
prevent serious injury. Deployment occurs • If the collision involves a nonrigid object (e.g.,
decals on both sun visors and on the front and a snow drift or bush), or a rigid, fixed object
very quickly and with considerable force.
far right side of the dash. at a low speed, the front airbags will not nec-
During normal deployment and depend-
The driver's side front airbag is folded and ing on variables such as seating position, essarily deploy.
located in the steering wheel hub. one may experience abrasions, bruises, • Front airbags do not normally deploy in a
The knee airbag is folded on the underside of swellings, or other injuries as a result of side impact collision, in a collision from the
the dashboard on the driver's side. The text deployment of one or both of the airbags. rear or in a rollover situation.
AIRBAG is embossed on the panel. • When installing any accessory equipment, • The amount of damage to the bodywork
make sure that the front airbag system is does not reliably indicate if the airbags
The passenger's side front airbag is folded
not damaged. Any interference in the sys- should have deployed or not.
behind a panel located above the glove compart-
tem could cause malfunction.
ment.
54
SAFETY
55
SAFETY
56
SAFETY
}}
57
SAFETY
|| Passenger's OWS indi- Passenger's person isn't sitting properly in the seat. If this Rockleigh, New Jersey 07647
happens:
seat occu- cator light side front air- 1-800-458-1552
pancy status status bag status • Turn the vehicle off and ask the person to
In Canada
place the backrest in an upright position.
Seat unoccu- OWS indi- Passenger's Volvo Car Canada Ltd.
pied cator light side front air- • Have the person sit upright in the seat, cen-
lights up. bag disabled tered on the seat cushion, with the person's Customer Care Centre
legs comfortably extended.
9130 Leslie Street, Suite 101
Seat occu- OWS indi- Passenger's
pied by low cator light side front air-
• Restart the vehicle and have the person
Richmond Hill, Ontario L4B 0B9
remain in this position for about two minutes.
weight occu- lights up bag disabled This will allow the system to detect that per- 1-800-663-8255
pant/objectA son and enable the passenger's frontal air-
Seat occu- OWS indi- Passenger's bag.
pied by heavy cator light is side front air- • If the PASSENGER AIRBAG OFF indicator
occupant/ not lit bag enabled lamp remains on even after this, the person
object should be advised to ride in the rear seat.
A Volvo recommends that children always be properly restrained This indicates limitations in OWS classification
in appropriate child restraints in the rear seats. Do not assume capability. It does not indicate OWS malfunction.
that the passenger's side front airbag is disabled unless the
PASSENGER AIRBAG OFF indicator lamp is lit. Make sure the
child restraint is properly installed. If there is any doubt as to the Modifications
status of the passenger's side front airbag, move the child
restraint to the rear seat. If you are considering modifying your vehicle in
any way to accommodate a disability, for example
The OWS is designed to enable (may inflate) the by altering or adapting the driver's or front pas-
passenger's side front airbag in the event of a senger's seat(s) and/or airbag systems, please
collision anytime the system senses that a per- contact Volvo at:
son of adult size is sitting properly in the front
In the United States
passenger's seat. The PASSENGER AIRBAG
OFF indicator lamp will be off and remain off. Volvo Car USA, LLC
If a person of adult size is sitting in the front pas- Customer Care Center
senger's seat, but the PASSENGER AIRBAG 1 Volvo Drive
OFF indicator lamp is on, it is possible that the
P.O. Box 914
58
SAFETY
59
SAFETY
WARNING
Do not place any objects in the area between
the outer edges of the seats and the door
panels, as this could impair the function of the
side airbags.
Volvo recommends only using seat covers
approved by Volvo. Other seat covers could
prevent the side airbags from functioning
The side airbags are located in the front seats' properly.
outer backrest frames and help protect the driver
and front seat passenger.
WARNING The inflatable curtains are installed along both
A collision of a sufficiently violent force will trig- sides of the inside of the roof and help protect
The side airbag is a supplement to the seat
ger the sensors and one or more side airbags will belt. Always wear your seat belt. occupants in the vehicle's outer seats. IC
inflate. The side airbags inflate between the seat AIRBAG is embossed on the panels.
occupant and the door panel to help cushion the
initial impact of the collision. The airbag deflates Related information A collision of a sufficiently violent force will trig-
when compressed by the collision. The side air- • Airbags (p. 52) ger the sensors and the inflatable curtain will
bags are normally only deployed on the side of inflate.
the vehicle impacted by the collision.
60
SAFETY
WARNING
The inflatable curtain is a supplement to the
seat belt. Always wear your seat belt.
}}
61
SAFETY
|| WARNING Starting and moving the vehicle 3. Then try to start the vehicle.
when it is in safety mode > The vehicle's electrical system will per-
Never attempt to perform repairs or reset
electrical components on your own after the If safety mode has been set, it may be possible form a system check and then attempt to
vehicle has been in safety mode. This could to reset the system in order to start and move reset to normal operating mode.
result in injury or prevent the vehicle from the vehicle a short distance, for example, if it is
functioning properly. Volvo recommends hav- blocking traffic. CAUTION
ing the vehicle inspected and reset to normal
operating status by an authorized Volvo work- Starting the vehicle when it is in safety If the message Safety mode See Owner's
shop after Safety mode See Owner's mode manual is still displayed, the vehicle should
manual has been displayed. 1. Check the vehicle for damage, particularly for not be driven or towed behind another vehi-
fuel leakage. Make sure you do not detect cle. If the vehicle needs to be moved, it must
any gasoline fumes. be towed on a tow truck. Even if no damage
WARNING is apparent, there may be hidden damage that
When the vehicle is in safety mode, it should If the damage to the vehicle is minor and could make the vehicle impossible to control.
not be towed behind another vehicle. It should there is no fuel leakage/fumes, you may
be towed from the site on a tow truck. Volvo attempt to start the engine.
recommends towing the vehicle directly to an
authorized Volvo workshop. Moving the vehicle when it is in safety
WARNING mode
Never attempt to restart the vehicle if you 1. If the message Normal mode The vehicle
Related information smell fuel fumes when the message Safety is now in normal mode is displayed after
• Safety (p. 42) mode See Owner's manual is displayed in attempting to start the engine, the vehicle
• Starting and moving the vehicle when it is in the instrument panel. Leave the vehicle imme-
may be moved carefully from its present
safety mode (p. 62) diately.
position if, for example, it is blocking traffic.
• Recovery (p. 455)
2. Do not move the vehicle farther than abso-
2. Switch off the ignition.
lutely necessary.
WARNING
When the vehicle is in safety mode, it should
not be towed behind another vehicle. It should
be towed from the site on a tow truck. Volvo
recommends towing the vehicle directly to an
authorized Volvo workshop.
62
SAFETY
Related information Child safety impact. The same can also happen if the infant or
• Safety mode (p. 61) Children should always be seated safely when child rides unrestrained on the seat. Other occu-
pants should also be properly restrained to help
• Starting the vehicle (p. 404) traveling in the vehicle.
reduce the chance of injuring or increasing the
• Recovery (p. 455) General information injury of a child.
Volvo recommends the proper use of restraint
All states and provinces have legislation govern-
systems for all occupants including children.
ing how and where children should be carried in
Remember that, regardless of age and size, a
a vehicle. Find out the regulations existing in your
child should always be properly restrained in a
state or province. Recent accident statistics have
vehicle.
shown that children are safer in rear seating
Your vehicle is also equipped with ISOFIX/ positions than front seating positions when prop-
LATCH attachments, which make it more conven- erly restrained. A child restraint system can help
ient to install child seats. protect a child in a vehicle. Here's what to look
for when selecting a child restraint system:
Some restraint systems for children are designed
to be secured in the vehicle by lap belts or the It should have a label certifying that it meets
lap portion of a lap-shoulder belt. Such child applicable Federal Motor Vehicle Safety Stand-
restraint systems can help protect children in ards (FMVSS 213) - or in Canada, CMVSS 213.
vehicles in the event of an accident only if they
Make sure the child restraint system is approved
are used properly. However, children could be
for the child's height, weight and development -
endangered in a crash if the child restraints are
the label required by the standard or regulation,
not properly secured in the vehicle. Failure to fol-
or instructions for infant restraints, typically pro-
low the installation instructions for your child
vide this information.
restraint can result in your child striking the vehi-
cle's interior in a sudden stop. In using any child restraint system, we urge you
to carefully look over the instructions that are
Holding a child in your arms is NOT a suitable
provided with the restraint. Be sure you under-
substitute for a child restraint system. In an acci-
stand them and can use the device properly and
dent, a child held in a person's arms can be
safely in this vehicle. A misused child restraint
crushed between the vehicle's interior and an
system can result in increased injuries for both
unrestrained person. The child could also be
the infant or child and other occupants in the
injured by striking the interior, or by being ejected
vehicle.
from the vehicle during a sudden maneuver or
}}
63
SAFETY
|| When a child has outgrown the child safety seat, WARNING remember to put your children in the back seat,
you should use the rear seat with the standard and buckle them up.
seat belt fastened. The best way to help protect • Do not use child safety seats or child
the child here is to place the child on a cushion booster cushions/backrests in the front
WARNING
so that the seat belt is properly located on the passenger's seat. We also recommend
hips. Legislation in your state or province may that children under 140 cm (4 feet A child restraint should never be reused if:
mandate the use of a child seat or cushion in 7 inches) in height who have outgrown • The vehicle has been involved in a colli-
combination with the seat belt, depending on the these devices sit in the rear seat with the sion, no matter how minor
child's age and/or size. Please check local regu- seat belt fastened.
• Its history is unknown
lations. • On hot days, the temperature in the vehi-
cle interior can rise very quickly. Exposure • It is older than the manufacturer's expira-
A specially designed and tested booster cushion tion date
and backrest can be obtained from your Volvo to these high temperatures for even a
retailer. See also the article "Integrated booster short period of time can cause heat-rela-
ted injury or death. Small children are par- Volvo has some very specific
cushion."
ticularly at risk. Never leave children unat- recommendations
tended in a vehicle. • Always wear your seat belt.
• Airbags are a SUPPLEMENTAL safety
Child seats should always be registered. device which, when used with a three-point
seat belt can help reduce serious injuries
Volvo's recommendations during certain types of accidents. Volvo rec-
Why does Volvo believe that no child should sit in ommends that you do not disconnect the air-
the front seat of a vehicle? It's quite simple really. bag system in your vehicle.
A front airbag is a very powerful device designed,
by law, to help protect an adult. • Volvo strongly recommends that everyone in
the vehicle be properly restrained.
Because of the size of the airbag and its speed
of inflation, a child should never be placed in the
• Volvo recommends that ALL occupants
(adults and children) shorter than 140 cm
front seat, even if he or she is properly belted or
(4 feet 7 inches) be seated in the rear seat
strapped into a child safety seat. Volvo has been
of any vehicle with a front passenger side air-
an innovator in the field of safety since it was
bag.
founded. And we have no intention of resting on
our laurels. But we need your help. Please • Drive safely!
64
SAFETY
Convertible seat
WARNING
A child seat should never be used in the front
passenger seat of any vehicle with a front
Infant seat passenger airbag - not even if the "Passenger
There are three main types of child restraint sys- airbag off" symbol near the rear-view mirror is
tems: infant seats, convertible seats and booster illuminated. If the severity of an accident were
to cause the airbag to inflate, this could lead
cushions. They are classified according to the
to serious injury or death to a child seated in
child's age and size. this position.
The child restraint should be secured using a
three-point seat belt, ISOFIX/LATCH anchors or
top tether anchors.
}}
65
SAFETY
66
SAFETY
WARNING
• An infant seat must be in the rear-facing
position only.
Do not place the infant seat in the front passenger's • The infant seat should not be positioned
seat behind the driver's seat unless there is
1. Place the infant seat in the rear seat of the adequate space for safe installation.
vehicle.
2. Attach the seat belt to the infant seat
according to the child restraint manufactur-
er's instructions.
}}
* Option/accessory. 67
SAFETY
|| WARNING NOTE
A child seat should never be used in the front The locking retractor will automatically
passenger seat of any vehicle with a front release when the seat belt is unbuckled and
passenger airbag - not even if the "Passenger allowed to retract fully.
airbag off" symbol near the rear-view mirror is
illuminated. If the severity of an accident were
to cause the airbag to inflate, this could lead 5. Press the infant seat firmly in place, let the
to serious injury or death to a child seated in seat belt retract and pull it taut. A sound from
this position. the seat belt retractor's automatic locking
function will be audible at this time and is
3. normal. The seat belt should now be locked
in place.
Pull out the shoulder section of the seat belt.
4. Pull the shoulder section of the seat belt out
as far as possible to activate the belt's auto-
matic locking function.
68
SAFETY
Related information
• Child restraints (p. 65)
• Convertible seats (p. 69)
• Booster cushions (p. 71) Route the seat belt through the convertible seat.
• Top tether anchors (p. 72)
• Lower child seat attachment points (p. 74) WARNING
Always use a convertible seat that is suitable
• ISOFIX/LATCH lower anchors (p. 74)
for the child's age and size. See the converti-
ble seat manufacturer's recommendations.
}}
69
SAFETY
|| WARNING NOTE
• A small child's head represents a consider- The locking retractor will automatically
able part of its total weight and its neck is release when the seat belt is unbuckled and
still very weak. Volvo recommends that allowed to retract fully.
children up to age 4 travel, properly
restrained, facing rearward. In addition, 5. Press the convertible seat firmly in place, let
Volvo recommends that children should the seat belt retract and pull it taut. A sound
ride rearward facing, properly restrained, as from the seat belt retractor's automatic lock-
long as possible. ing function will be audible at this time and is
• Convertible child seats should be installed normal. The seat belt should now be locked
in the rear seat only. in place.
• A rear-facing convertible seat should not Fasten the seat belt.
be positioned behind the driver's seat 3. Fasten the seat belt by inserting the latch
unless there is adequate space for safe plate into the buckle (lock) until a distinct
installation. click is audible.
4. Pull the shoulder section of the seat belt out
2. Attach the seat belt to the convertible seat as far as possible to activate the belt's auto-
according to the child restraint manufactur- matic locking function.
er's instructions.
70
SAFETY
}}
71
SAFETY
|| 3. Fasten the seat belt by inserting the latch Related information Top tether anchors
plate into the buckle (lock) until a distinct • Child restraints (p. 65) Your Volvo is equipped with child restraint top
click is audible.
• Convertible seats (p. 69) tether anchorages for all three seating positions
in the rear seat. They are located on the rear
• Infant seats (p. 67)
side of the backrests.
• Top tether anchors (p. 72)
• Lower child seat attachment points (p. 74) Child restraint anchorages
• ISOFIX/LATCH lower anchors (p. 74)
72
SAFETY
Related information
• Child restraints (p. 65)
• Lower child seat attachment points (p. 74)
73
SAFETY
Lower child seat attachment points Related information ISOFIX/LATCH lower anchors
The vehicle is equipped with lower child restraint • Child restraints (p. 65) Lower anchors for ISOFIX/LATCH-equipped
attachment points in the second row of seats. • Top tether anchors (p. 72) child seats are located in the second row, out-
The lower child seat attachment points are board seats, hidden below the backrest cush-
intended for use with certain rear-facing child
• ISOFIX/LATCH lower anchors (p. 74)
ions.
restraints.
Using the ISOFIX/LATCH lower child
Always follow the manufacturer's installation seat anchors
instructions when attaching a child seat to the
lower child seat attachment points.
74
SAFETY
75
SAFETY
76 * Option/accessory.
SAFETY
}}
* Option/accessory. 77
SAFETY
78 * Option/accessory.
SAFETY
* Option/accessory. 79
DISPLAYS AND VOICE CONTROL
DISPLAYS AND VOICE CONTROL
Ceiling console
Center display
Start knob
Parking lights, daytime running lights, low
beams, high beams, turn signals, front fog Drive modes*
lights/cornering illumination*, rear fog light,
trip computer reset Front reading lights and courtesy lighting Parking brake
Steering wheel paddles for manual shifting* Panoramic roof* Auto-hold brakes
Head-up display* Ceiling console display
Driver's door
Instrument panel HomeLink®*
Wipers and washers, rain sensor*
Center and tunnel console
Right-side steering wheel keypad
82 * Option/accessory.
DISPLAYS AND VOICE CONTROL
Related information
• Manual front seats (p. 188)
• Adjusting the power front seats* (p. 189)
• Adjusting the steering wheel (p. 203)
• Lighting panel and controls (p. 154)
• Starting the vehicle (p. 404)
• Instrument panel (p. 84)
• Center display overview (p. 111)
• Transmission (p. 417)
* Option/accessory. 83
DISPLAYS AND VOICE CONTROL
Cruise control/speed limiter information Message (also graphics in some cases) Fuel gauge
Road sign information* Door and seat belt status Start/Stop function's status
– Media player Distance to empty tank
84 * Option/accessory.
DISPLAYS AND VOICE CONTROL
* Option/accessory. 85
DISPLAYS AND VOICE CONTROL
Distance to empty tank Start/Stopp function's status App menu (activated using steering wheel keypad)
Ambient temperature sensor – Current fuel consumption
Indicator and warning symbols – OdometerB
– – Trip odometer
– – Indicator and warning symbols
– – Voice Control
– – Engine temperature gauge
– – Message (also graphics in some cases)
– – CompassA
A Depends on selected drive mode.
B Total distance.
86
DISPLAYS AND VOICE CONTROL
Related information
• Instrument panel settings (p. 88)
• Warning symbols in the instrument panel
(p. 97)
• Indicator symbols in the instrument panel
(p. 95)
• Trip computer (p. 89)
• Messages in the instrument panel (p. 106)
• Handling the App menu in the instrument
panel (p. 105)
87
DISPLAYS AND VOICE CONTROL
Instrument panel settings Select theme • Changing settings in the center display
Display settings for the instrument panel can be 1. Tap Settings in the center display's Top (p. 136)
set in the instrument panel's app menu and in view.
the center display's Settings menu.
2. Tap My Car Displays Display
Settings in instrument panel's app Themes
menu 3. Select a theme (appearance) for the instru-
The app menu can be used to set what informa- ment panel:
tion will be displayed in the instrument panel:
• Glass
• trip computer
• Minimalistic
• media player
• Performance
• phone
• Chrome Rings.
• navigation system*.
Select language
Center display settings 1. Tap Settings in the center display's Top
view.
Selecting type of information
1. Tap Settings in the center display's Top 2. Tap System System Languages and
view. Units System Language to select lan-
guage.
2. Tap My Car Displays Driver Display
Information. > A change made here will affect the lan-
guage in all displays.
3. Select a background:
The settings are personal and saved automati-
• Show no information in the cally in the active driver profile.
background
Related information
• Show information for current playing
media • Instrument panel (p. 84)
• Show navigation even if no route is • Handling the App menu in the instrument
panel (p. 105)
set1.
1 The map is only shown with the 12" instrument panel*. With the 8" instrument panel, only guidance is shown.
88 * Option/accessory.
DISPLAYS AND VOICE CONTROL
}}
89
DISPLAYS AND VOICE CONTROL
90 * Option/accessory.
DISPLAYS AND VOICE CONTROL
• Displaying trip statistics in the center display Displaying trip data in the 1. Open the app menu in the instrument panel
(p. 92) instrument panel by pressing (1).
• Instrument panel (p. 84) Data recorded and calculated by the trip com- (The App menu cannot be opened while
puter can be displayed on the instrument panel. there is an unacknowledged message in the
This data is stored in a trip computer app. You instrument panel. The message must be con-
can choose which information the instrument firmed before the App menu can be opened.)
panel will display in the app menu.
2. Navigate to the trip computer app by moving
left or right using (2).
> The top four menu rows show measured
values for trip odometer TM. The next four
menu rows show measured values for trip
odometer TA. Scroll up or down in the list
using (3).
3. Scroll down to the option buttons to choose
which information to show in the instrument
panel:
• Distance to empty tank
• Odometer
Open and navigate in the app menu2 using the right-
hand steering wheel keypad. • Mileage for trip odometer TM, TA or no
display of mileage
App menu
• Current fuel consumption, average fuel
Left/right consumption for TM or TA, or no display
of fuel consumption
Up/down
• Tourist (alternative speedometer).
Confirm Select or clear a selection using the O but-
ton (4). The change will apply immediately.
91
DISPLAYS AND VOICE CONTROL
|| Related information Resetting the trip odometer Displaying trip statistics in the
• Trip computer (p. 89) Resetting the trip odometer using the left-side center display
• Resetting the trip odometer (p. 92) steering wheel lever. Trip computer statistics can be displayed graphi-
cally in the center display, providing an overview
that facilitates more fuel-efficient driving.
Related information
• Trip computer (p. 89)
92
DISPLAYS AND VOICE CONTROL
Related information
• change the graph scale. Select 1, 10 or
100 km/miles for the bar.
• Trip statistics settings (p. 93)
• reset data after each trip. Performed when
• Trip computer (p. 89) the vehicle remains stationary for more
than 4 hours.
• reset data for current trip.
Trip statistics, calculated average consump-
tion, and total driving time are always reset
simultaneously.
Unit standards for distance, speed, etc. can be
changed via system settings in the center display.
Related information
• Displaying trip statistics in the center display
(p. 92)
• Trip computer (p. 89)
93
DISPLAYS AND VOICE CONTROL
Date and time Automatic time for vehicles with GPS Ambient temperature sensor
The clock is displayed in both the instrument When the vehicle is equipped with a navigation The ambient temperature is shown in the instru-
panel and the center display. system, Auto Time is also available. The time ment panel.
zone will then be automatically set to the vehi- The sensor detects the temperature outside the
Location of clock cle's location. In some navigation systems, the vehicle.
current location must also be set to determine
the correct time zone. If Auto Time is not
selected, the time and date can be adjusted
using the up and down arrows on the
touchscreen.
Daylight savings time
In some countries, an automatic change to day-
light savings time can be selected by activating
Auto. For other countries, daylight savings time
can be changed by selecting On or Off.
Related information
Location of clock in 12" and 8" instrument panels. • Instrument panel (p. 84)
Location of the ambient temperature sensor in 12" and
In the center display, the clock is located at the • Changing settings in the center display 8" instrument panels.
top right of the status bar. (p. 136)
If the vehicle has been stationary, the sensor
Certain messages and other information may reading may be higher than the actual tempera-
obscure the clock in the instrument panel. ture.
94
DISPLAYS AND VOICE CONTROL
To change the measurement standard for the Indicator symbols in the instrument Symbol Meaning
temperature sensor and other readings, go to panel
system settings in the center display's Top view. The indicator symbols alert the driver that a func- Fault in ABS system
tion has been activated, that a system is running, If this symbol is illuminated, the
Related information
or that a fault or error may have occurred. ABS system is malfunctioning. The
• Instrument panel (p. 84)
Symbol Meaning A vehicle's regular brakes will still
• Changing system units of measurement work, but without the ABS function.
(p. 134) Information, see the message in
the display
The information symbol illuminates
and a message is displayed in the B
instrument panel if one of the vehi-
cle's systems requires the driver's Auto-brake on
attention. The information symbol
may also illuminate in combination This symbol illuminates when the
with other symbols. function is activated and the brakes
A or parking brakes are being used.
Fault in brake system The brakes hold the vehicle at a
This symbol illuminates if there is a standstill after it has stopped.
problem with the parking brake.
A
B
}}
95
DISPLAYS AND VOICE CONTROL
96
DISPLAYS AND VOICE CONTROL
97
DISPLAYS AND VOICE CONTROL
98
DISPLAYS AND VOICE CONTROL
Boost Software License 1.0 BSD 4-clause "Original" or "Old" License AND FITNESS FOR A PARTICULAR PURPOSE
Permission is hereby granted, free of charge, to Copyright (c) 1982, 1986, 1990, 1991, 1993 ARE DISCLAIMED. IN NO EVENT SHALL THE
any person or organization obtaining a copy of The Regents of the University of California. All REGENTS OR CONTRIBUTORS BE LIABLE
the software and accompanying documentation rights reserved. FOR ANY DIRECT, INDIRECT, INCIDENTAL,
covered by this license (the "Software") to use, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
Redistribution and use in source and binary
reproduce, display, distribute, execute, and DAMAGES (INCLUDING, BUT NOT LIMITED TO,
forms, with or without modification, are permitted
transmit the Software, and to prepare derivative PROCUREMENT OF SUBSTITUTE GOODS OR
provided that the following conditions are met:
works of the Software, and to permit third-parties SERVICES; LOSS OF USE, DATA, OR PROFITS;
to whom the Software is furnished to do so, all 1. Redistributions of source code must retain OR BUSINESS INTERRUPTION) HOWEVER
subject to the following: The copyright notices in the above copyright notice, this list of CAUSED AND ON ANY THEORY OF LIABILITY,
the Software and this entire statement, including conditions and the following disclaimer. WHETHER IN CONTRACT, STRICT LIABILITY,
the above license grant, this restriction and the 2. Redistributions in binary form must OR TORT (INCLUDING NEGLIGENCE OR
following disclaimer, must be included in all reproduce the above copyright notice, this list OTHERWISE) ARISING IN ANY WAY OUT OF
copies of the Software, in whole or in part, and all of conditions and the following disclaimer in THE USE OF THIS SOFTWARE, EVEN IF
derivative works of the Software, unless such the documentation and/or other materials ADVISED OF THE POSSIBILITY OF SUCH
copies or derivative works are solely in the form provided with the distribution. DAMAGE.
of machine-executable object code generated by
3. All advertising materials mentioning features
a source language processor.
or use of this software must display the
THE SOFTWARE IS PROVIDED "AS IS", following acknowledgement: This product
WITHOUT WARRANTY OF ANY KIND, includes software developed by the
EXPRESS OR IMPLIED, INCLUDING BUT NOT University of California, Berkeley and its
LIMITED TO THE WARRANTIES OF contributors.
MERCHANTABILITY, FITNESS FOR A 4. Neither the name of the University nor the
PARTICULAR PURPOSE, TITLE AND NON- names of its contributors may be used to
INFRINGEMENT. IN NO EVENT SHALL THE endorse or promote products derived from
COPYRIGHT HOLDERS OR ANYONE this software without specific prior written
DISTRIBUTING THE SOFTWARE BE LIABLE permission.
FOR ANY DAMAGES OR OTHER LIABILITY,
WHETHER IN CONTRACT, TORT OR THIS SOFTWARE IS PROVIDED BY THE
OTHERWISE, ARISING FROM, OUT OF OR IN REGENTS AND CONTRIBUTORS ``AS IS'' AND
CONNECTION WITH THE SOFTWARE OR THE ANY EXPRESS OR IMPLIED WARRANTIES,
USE OR OTHER DEALINGS IN THE INCLUDING, BUT NOT LIMITED TO, THE
SOFTWARE. IMPLIED WARRANTIES OF MERCHANTABILITY
}}
99
DISPLAYS AND VOICE CONTROL
|| BSD 3-clause "New" or "Revised" License SERVICES; LOSS OF USE, DATA, OR PROFITS; OR CONTRIBUTORS BE LIABLE FOR ANY
Copyright (c) 2011-2014, Yann Collet. OR BUSINESS INTERRUPTION) HOWEVER DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
CAUSED AND ON ANY THEORY OF LIABILITY, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
Redistribution and use in source and binary
WHETHER IN CONTRACT, STRICT LIABILITY, (INCLUDING, BUT NOT LIMITED TO,
forms, with or without modification, are permitted
OR TORT (INCLUDING NEGLIGENCE OR PROCUREMENT OF SUBSTITUTE GOODS OR
provided that the following conditions are met:
OTHERWISE) ARISING IN ANY WAY OUT OF SERVICES; LOSS OF USE, DATA, OR PROFITS;
1. Redistributions of source code must retain THE USE OF THIS SOFTWARE, EVEN IF OR BUSINESS INTERRUPTION) HOWEVER
the above copyright notice, this list of ADVISED OF THE POSSIBILITY OF SUCH CAUSED AND ON ANY THEORY OF LIABILITY,
conditions and the following disclaimer. DAMAGE. WHETHER IN CONTRACT, STRICT LIABILITY,
2. Redistributions in binary form must BSD 2-clause “Simplified” license OR TORT (INCLUDING NEGLIGENCE OR
reproduce the above copyright notice, this list Copyright (c) <YEAR>, <OWNER> All rights OTHERWISE) ARISING IN ANY WAY OUT OF
of conditions and the following disclaimer in reserved. THE USE OF THIS SOFTWARE, EVEN IF
the documentation and/or other materials ADVISED OF THE POSSIBILITY OF SUCH
Redistribution and use in source and binary DAMAGE.
provided with the distribution.
forms, with or without modification, are permitted
3. Neither the name of the organisation nor the provided that the following conditions are met: The views and conclusions contained in the
names of its contributors may be used to software and documentation are those of the
endorse or promote products derive from this 1. Redistributions of source code must retain authors and should not be interpreted as
software without specific prior written the above copyright notice, this list of representing official policies, either expressed or
permission. conditions and the following disclaimer. implied, of the FreeBSD Project.
THIS SOFTWARE IS PROVIDED BY THE 2. Redistributions in binary form must
COPYRIGHT HOLDERS AND CONTRIBUTORS reproduce the above copyright notice, this list
"AS IS" AND ANY EXPRESS OR IMPLIED of conditions and the following disclaimer in
WARRANTIES, INCLUDING, BUT NOT LIMITED the documentation and/or other materials
TO, THE IMPLIED WARRANTIES OF provided with the distribution.
MERCHANTABILITY AND FITNESS FOR A THIS SOFTWARE IS PROVIDED BY THE
PARTICULAR PURPOSE ARE DISCLAIMED. IN COPYRIGHT HOLDERS AND CONTRIBUTORS
NO EVENT SHALL THE COPYRIGHT HOLDER "AS IS" AND ANY EXPRESS OR IMPLIED
OR CONTRIBUTORS BE LIABLE FOR ANY WARRANTIES, INCLUDING, BUT NOT LIMITED
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, TO, THE IMPLIED WARRANTIES OF
EXEMPLARY, OR CONSEQUENTIAL DAMAGES MERCHANTABILITY AND FITNESS FOR A
(INCLUDING, BUT NOT LIMITED TO, PARTICULAR PURPOSE ARE DISCLAIMED. IN
PROCUREMENT OF SUBSTITUTE GOODS OR NO EVENT SHALL THE COPYRIGHT OWNER
100
DISPLAYS AND VOICE CONTROL
FreeType Project License provided that all warranty or liability claims IN NO EVENT WILL ANY OF THE
1. 1 Copyright 1996-1999 by David Turner, are assumed by the product vendor. Legal AUTHORS OR COPYRIGHT HOLDERS BE
Robert Wilhelm, and Werner Lemberg Terms 0. Definitions Throughout this license, LIABLE FOR ANY DAMAGES CAUSED BY
Introduction The FreeType Project is the terms `package', `FreeType Project', and THE USE OR THE INABILITY TO USE, OF
distributed in several archive packages; some `FreeType archive' refer to the set of files THE FREETYPE PROJECT. As you have not
of them may contain, in addition to the originally distributed by the authors (David signed this license, you are not required to
FreeType font engine, various tools and Turner, Robert Wilhelm, and Werner accept it. However, as the FreeType project
contributions which rely on, or relate to, the Lemberg) as the `FreeType project', be they is copyrighted material, only this license, or
FreeType Project. This license applies to all named as alpha, beta or final release. `You' another one contracted with the authors,
files found in such packages, and which do refers to the licensee, or person using the grants you the right to use, distribute, and
not fall under their own explicit license. The project, where `using' is a generic term modify it. Therefore, by using, distributing, or
license affects thus the FreeType font including compiling the project's source code modifying the FreeType project, you indicate
engine, the test programs, documentation as well as linking it to form a `program' or that you understand and accept all the terms
and makefiles, at the very least. This license `executable'. This program is referred to as `a of this license.
was inspired by the BSD, Artistic, and IJG program using the FreeType engine'. This 2. Redistribution Redistribution and use in
(Independent JPEG Group) licenses, which license applies to all files distributed in the source and binary forms, with or without
all encourage inclusion and use of free original FreeType archive, including all source modification, are permitted provided that the
software in commercial and freeware code, binaries and documentation, unless following conditions are met: o Redistribution
products alike. As a consequence, its main otherwise stated in the file in its original, of source code must retain this license file
points are that: o We don't promise that this unmodified form as distributed in the original (`licence.txt') unaltered; any additions,
software works. However, we are be archive. If you are unsure whether or not a deletions or changes to the original files
interested in any kind of bug reports. (`as is' particular file is covered by this license, you must be clearly indicated in accompanying
distribution) o You can use this software for must contact us to verify this. The FreeType documentation. The copyright notices of the
whatever you want, in parts or full form, project is copyright (C) 1996-1999 by David unaltered, original files must be preserved in
without having to pay us. (`royalty-free' Turner, Robert Wilhelm, and Werner all copies of source files. o Redistribution in
usage) o You may not pretend that you wrote Lemberg. All rights reserved except as binary form must provide a disclaimer that
this software. If you use it, or only parts of it, specified below. 1. No Warranty THE states that the software is based in part of
in a program, you must acknowledge FREETYPE ARCHIVE IS PROVIDED `AS IS' the work of the FreeType Team, in the
somewhere in your documentation that WITHOUT WARRANTY OF ANY KIND, distribution documentation. We also
you've used the FreeType code. (`credits') EITHER EXPRESSED OR IMPLIED, encourage you to put an URL to the
We specifically permit and encourage the INCLUDING, BUT NOT LIMITED TO, FreeType web page in your documentation,
inclusion of this software, with or without WARRANTIES OF MERCHANTABILITY AND though this isn't mandatory. These conditions
modifications, in commercial products, FITNESS FOR A PARTICULAR PURPOSE. apply to any software derived from or based
}}
101
DISPLAYS AND VOICE CONTROL
|| on the FreeType code, not just the Libpng License libpng versions 0.97, January 1998, through
unmodified files. If you use our work, you This copy of the libpng notices is provided for 1.0.6, March 20, 2000, are Copyright (c) 1998,
must acknowledge us. However, no fee need your convenience. In case of any discrepancy 1999 Glenn Randers-Pehrson, and are
be paid to us. between this copy and the notices in the file distributed according to the same disclaimer and
3. Advertising The names of FreeType's authors png.h that is included in the libpng distribution, license as libpng-0.96, with the following
and contributors may not be used to endorse the latter shall prevail. individuals added to the list of Contributing
or promote products derived from this Authors:
COPYRIGHT NOTICE, DISCLAIMER, and
software without specific prior written LICENSE: Tom Lane
permission. We suggest, but do not require,
If you modify libpng you may insert additional Glenn Randers-Pehrson
that you use one or more of the following
phrases to refer to this software in your notices immediately following this sentence. Willem van Schaik
documentation or advertising materials: libpng versions 1.0.7, July 1, 2000, through libpng versions 0.89, June 1996, through 0.96,
`FreeType Project', `FreeType Engine', 1.0.13, April 15, 2002, are Copyright (c) May 1997, are Copyright (c) 1996, 1997
`FreeType library', or `FreeType Distribution'. 2000-2002 Glenn Randers-Pehrson and are Andreas Dilger Distributed according to the same
4. Contacts There are two mailing lists related distributed according to the same disclaimer and disclaimer and license as libpng-0.88, with the
to FreeType: o freetype@freetype.org license as libpng-1.0.6 with the following following individuals added to the list of
Discusses general use and applications of individuals added to the list of Contributing Contributing Authors:
FreeType, as well as future and wanted Authors
additions to the library and distribution. If you John Bowler
Simon-Pierre Cadieux
are looking for support, start in this list if you Kevin Bracey
haven't found anything to help you in the Eric S. Raymond
Sam Bushell
documentation. o devel@freetype.org Gilles Vollant
Discusses bugs, as well as engine internals, Magnus Holmgren
and with the following additions to the disclaimer:
design issues, specific licenses, porting, etc. Greg Roelofs
o http://www.freetype.org Holds the current There is no warranty against interference with
FreeType web page, which will allow you to your enjoyment of the library or against Tom Tanner
download our latest development version and infringement. There is no warranty that our efforts libpng versions 0.5, May 1995, through 0.88,
read online documentation. You can also or the library will fulfill any of your particular January 1996, are Copyright (c) 1995, 1996 Guy
contact us individually at: David Turner purposes or needs. This library is provided with all Eric Schalnat, Group 42, Inc.
<david.turner@freetype.org> Robert Wilhelm faults, and the entire risk of satisfactory quality,
<robert.wilhelm@freetype.org> Werner performance, accuracy, and effort is with the user.
Lemberg <werner.lemberg@freetype.org>
102
DISPLAYS AND VOICE CONTROL
For the purposes of this copyright and license, 3. This Copyright notice may not be removed or sublicense, and/or sell copies of the Software,
"Contributing Authors" is defined as the following altered from any source or altered source and to permit persons to whom the Software is
set of individuals: distribution. furnished to do so, subject to the following
The Contributing Authors and Group 42, Inc. conditions:
Andreas Dilger
specifically permit, without fee, and encourage The above copyright notice and this permission
Dave Martindale
the use of this source code as a component to notice shall be included in all copies or
Guy Eric Schalnat supporting the PNG file format in commercial substantial portions of the Software.
products. If you use this source code in a product,
Paul Schmidt THE SOFTWARE IS PROVIDED "AS IS",
acknowledgment is not required but would be
Tim Wegner WITHOUT WARRANTY OF ANY KIND,
appreciated.
EXPRESS OR IMPLIED, INCLUDING BUT NOT
The PNG Reference Library is supplied "AS IS". A "png_get_copyright" function is available, for LIMITED TO THE WARRANTIES OF
The Contributing Authors and Group 42, Inc. convenient use in "about" boxes and the like: MERCHANTABILITY, FITNESS FOR A
disclaim all warranties, expressed or implied, PARTICULAR PURPOSE AND
printf("%s",png_get_copyright(NULL));
including, without limitation, the warranties of NONINFRINGEMENT. IN NO EVENT SHALL
merchantability and of fitness for any purpose. Also, the PNG logo (in PNG format, of course) is THE AUTHORS OR COPYRIGHT HOLDERS BE
The Contributing Authors and Group 42, Inc. supplied in the files "pngbar.png" and LIABLE FOR ANY CLAIM, DAMAGES OR
assume no liability for direct, indirect, incidental, "pngbar.jpg (88x31) and "pngnow.png" (98x31). OTHER LIABILITY, WHETHER IN AN ACTION
special, exemplary, or consequential damages, OF CONTRACT, TORT OR OTHERWISE,
Libpng is OSI Certified Open Source Software.
which may result from the use of the PNG ARISING FROM, OUT OF OR IN CONNECTION
OSI Certified Open Source is a certification mark
Reference Library, even if advised of the WITH THE SOFTWARE OR THE USE OR
of the Open Source Initiative.
possibility of such damage. OTHER DEALINGS IN THE SOFTWARE.
Glenn Randers-Pehrson randeg@alum.rpi.edu
Permission is hereby granted to use, copy,
April 15, 2002
modify, and distribute this source code, or
portions hereof, for any purpose, without fee, MIT License
subject to the following restrictions: Copyright (c) <year> <copyright holders>
1. The origin of this source code must not be Permission is hereby granted, free of charge, to
misrepresented. any person obtaining a copy of this software and
associated documentation files (the "Software"),
2. Altered versions must be plainly marked as
to deal in the Software without restriction,
such and must not be misrepresented as
including without limitation the rights to use,
being the original source.
copy, modify, merge, publish, distribute,
}}
103
DISPLAYS AND VOICE CONTROL
|| zlib License documentation files (the "Software"), to deal in App menu in instrument panel
The zlib/libpng License Copyright (c) <year> the Software without restriction, including without The application menu (App menu) in the instru-
<copyright holders> limitation the rights to use, copy, modify, merge, ment panel provides quick access to commonly
publish, distribute, sublicense, and/or sell copies used functions for certain apps.
This software is provided 'as-is', without any
of the Software, and to permit persons to whom
express or implied warranty. In no event will the
the Software is furnished to do so, subject to the
authors be held liable for any damages arising
following conditions: The above copyright notice
from the use of this software.
including the dates of first publication and either
Permission is granted to anyone to use this this permission notice or a reference to http://
software for any purpose, including commercial oss.sgi.com/projects/FreeB/ shall be included in
applications, and to alter it and redistribute it all copies or substantial portions of the Software.
freely, subject to the following restrictions:
THE SOFTWARE IS PROVIDED "AS IS",
1. The origin of this software must not be WITHOUT WARRANTY OF ANY KIND,
misrepresented; you must not claim that you EXPRESS OR IMPLIED, INCLUDING BUT NOT
wrote the original software. If you use this LIMITED TO THE WARRANTIES OF
software in a product, an acknowledgment in MERCHANTABILITY, FITNESS FOR A
the product documentation would be PARTICULAR PURPOSE AND
appreciated but is not required. NONINFRINGEMENT. IN NO EVENT SHALL The App menu in the instrument panel can be used
instead of the center display. The illustration is generic –
2. Altered source versions must be plainly SILICON GRAPHICS, INC. BE LIABLE FOR ANY layout may vary.
marked as such, and must not be CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, The App menu is displayed in the instrument
misrepresented as being the original panel and is controlled using the right-side steer-
software. TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE ing wheel keypad. The app menu makes it easier
3. This notice may not be removed or altered OR THE USE OR OTHER DEALINGS IN THE to switch between different apps or functions
from any source distribution. SOFTWARE. within the apps without having to let go of the
SGI Free Software B License Version 2.0. steering wheel.
Except as contained in this notice, the name of
SGI FREE SOFTWARE LICENSE B (Version 2.0,
Silicon Graphics, Inc. shall not be used in App menu functions
Sept. 18, 2008)
advertising or otherwise to promote the sale, use Different apps provide access to different types
Copyright (C) [dates of first publication] Silicon or other dealings in this Software without prior of functions. The following apps and their func-
Graphics, Inc. All Rights Reserved. Permission is written authorization from Silicon Graphics, Inc. tions can be controlled from the App menu:
hereby granted, free of charge, to any person
obtaining a copy of this software and associated Related information
• Instrument panel (p. 84)
104
DISPLAYS AND VOICE CONTROL
App Functions Handling the App menu in the Opening and closing the app menu
instrument panel – Tap open/close (1).
Trip com- Select a trip odometer, change The App (application) menu in the instrument (The App menu cannot be opened while
puter instrument panel display set- panel is controlled using the right-side steering there is an unacknowledged message in the
tings, etc. wheel keypad. instrument panel. The message must be con-
Media player Select active source for media firmed before the App menu can be opened.)
player. > The App men opens/closes.
Phone Call a contact from the call list. The App menu turns off automatically after a
period of inactivity or after certain selections are
Navigation Guide to destination, etc. made.
}}
105
DISPLAYS AND VOICE CONTROL
|| Related information Messages in the instrument panel High-priority messages for the driver are dis-
• App menu in instrument panel (p. 104) The instrument panel shows messages in certain played in the instrument panel.
• Messages in the instrument panel (p. 106) circumstances to inform or assist the driver. The messages may appear in different parts of
the instrument panel depending on what other
information is currently being displayed. The mes-
sage will disappear from the instrument panel
after a short period of time or after it has been
acknowledged or any required action has been
taken. Messages that need to be saved are
stored in the Car status app, which can be
opened from the App view in the center display.
The message may be shown along with graphics,
symbols or buttons to e.g. acknowledge the mes-
sage or accept a request.
Message in the instrument panel4.
106
DISPLAYS AND VOICE CONTROL
107
DISPLAYS AND VOICE CONTROL
108
DISPLAYS AND VOICE CONTROL
Handling messages saved from the Reading saved messages Booking service for saved messages:
instrument panel To read a saved message immediately: – With the message in expanded form, tap
Messages saved from the instrument panel and – Tap the button to the right of the message Request appoint.Call to make
center displays are handled in the center display. Car message stored in Car Status Appointment8 for assistance booking serv-
application in the center display. ice.
> The saved message will be displayed in > With Request appoint.: The
the Car status app. Appointments tab will open in the app
and create a request for a service/repair
To read saved messages at a later time:
appointment.
1. Open the Car status app from App view in
With Call to make Appointment: The
the center display.
phone app will open and call a service
> The app will open in the bottom tile of center to make an appointment for service
Home view. or repairs.
2. Select the Messages tab in the app. Reading the Owner's Manual for saved mes-
> A list of saved messages will be displayed. sages:
Saved messages can be viewed in the Car Status app.
3. Tap a message to expand/minimize it. – With the message in expanded form, tap
The messages displayed in the Owner's manual to read relevant informa-
> More information about the message will
instrument panel that need to tion about the message in the Owner's Man-
appear in the list and the image to the left
be saved are stored in the Car of the app will display information about ual.
status app in the center dis- the message in graphic form. > The Owner's Manual will open in the cen-
play. The message Car
Handling saved messages ter display and provide information related
message stored in Car
In expanded form, some messages have two but- to the message.
Status application will simul-
taneously appear in the center display. tons available for booking service or reading the Saved messages in the app are automatically
Owner's Manual. deleted each time the engine is started.
109
DISPLAYS AND VOICE CONTROL
|| Related information
• Messages in the instrument panel (p. 106)
• Handling messages in the instrument panel
(p. 107)
• Messages in the center display (p. 142)
110
DISPLAYS AND VOICE CONTROL
}}
111
DISPLAYS AND VOICE CONTROL
||
Three of the center display's basic views. Swipe to the right/left to access Function or App view9.
Function view ‒ vehicle functions that can be functions, called "trigger functions", open is the Camera. Settings for the head-up dis-
activated or deactivated with one tap. Certain windows with settings options. One example play* are also started from Function view, but
9 In right-hand drive vehicles, these views are mirror images of the ones shown here.
112 * Option/accessory.
DISPLAYS AND VOICE CONTROL
adjusted using the right-side steering wheel Fourth tile ‒ most recently used apps or • Changing system language (p. 134)
keypad. vehicle functions not associated with the • Changing system units of measurement
Home view ‒ the initial view displayed when other tiles. Tap the tile to expand it. (p. 134)
the screen is turned on. Climate row - information and direct interac- • Cleaning the center display (p. 615)
App view ‒ shows downloaded apps (third- tion to set temperature and seat heating for
example*. Tap the symbol in the center of the • Messages in the center display (p. 142)
party apps) as well as apps for integrated
functions, such as FM radio. Tap an app icon climate bar to open Climate view and addi-
to open that app. tional setting options.
Status bar ‒ current vehicle activities are Related information
shown at the top of the screen. Network and • Handling the center display (p. 114)
connection information is shown to the left of
the status bar. Media-related information, the
• Navigating in the center display's views
(p. 117)
clock and information about background
activities are shown to the right. • Function view in the center display (p. 124)
Top view ‒ pull the tab down to open Top • Apps (p. 465)
view. From here, you can access Settings, • Symbols in the center display status bar
Owner's manual, Profile and messages (p. 126)
stored in the vehicle. In certain cases, con-
• Opening settings in the center display
textual setting (e.g. Navigation Settings) (p. 134)
and the contextual Owner's Manual (e.g.
Navigation Manual) can also be accessed • Opening contextual setting in the center dis-
in Top view. play (p. 135)
Navigation ‒ takes you to map navigation • Owner's Manual in the center display (p. 17)
with e.g. Sensus Navigation*. Tap the tile to • Media player (p. 485)
expand it. • Phone (p. 498)
Media ‒ most recently used media-related • Climate system controls (p. 217)
apps. Tap the tile to expand it.
• Turning off and adjusting the volume of the
Phone ‒ used to access phone-related func- center display system sounds (p. 133)
tions. Tap the tile to expand it.
• Changing the appearance of the center dis-
play (p. 133)
* Option/accessory. 113
DISPLAYS AND VOICE CONTROL
Handling the center display ent views, mark objects, scroll in a list and move CAUTION
Many of the vehicle's functions and features can apps by touching the screen in various ways.
Do not use sharp objects on the screen as
be controlled and adjusted from the center dis- An infrared light curtain just above the surface of this could cause scratches.
play. The center display is a touchscreen that the screen enables the screen to detect when a
reacts to taps and other gestures. finger is directly in front of the screen. This tech-
nology makes it possible to use the screen even
Using the center display's touchscreen while wearing gloves.
The following table presents the various proce-
The touchscreen reacts differently depending on dures for using the screen:
whether the user taps, drags or swipes the Two people can interact with the screen at the
screen. It is possible to e.g. move between differ- same time, e.g. to adjust climate system settings
for both the driver and passenger sides.
Tap once with two Zooms out from a digital object, such as a map*.
fingers.
114 * Option/accessory.
DISPLAYS AND VOICE CONTROL
Swipe Moves between screen views or scrolls in a list, text or a view. Drag horizontally or vertically over the screen.
Note that touching the upper part of the screen could cause Top view to open.
}}
* Option/accessory. 115
DISPLAYS AND VOICE CONTROL
|| Returning to Home view from another • drag the control to the desired temperature,
view • tap + or − to raise or lower the temperature
1. Briefly press the home button below the cen- by degrees, or
ter display.
• tap the desired temperature on the control.
> The most recent Home view mode will be
displayed. Related information
2. Press briefly again. • Activating and deactivating the center display
(p. 117)
> All of the Home view's tiles will return to
standard mode. • Moving apps and buttons in the center dis-
play (p. 126)
NOTE • Using the center display keyboard (p. 128)
The scroll indicator will be shown in the center display
In Home view's standard mode – short press when it is possible to scroll in the view.
on the Home button. An animation describing
access to the various views is shown on the Using the center display controls
screen.
Temperature control.
Digital controls are available for many of the vehi-
cle's functions. For example, to set the tempera-
ture:
116
DISPLAYS AND VOICE CONTROL
Activating and deactivating the 1. Press and hold the button beneath the Navigating in the center display's
center display screen. views
The center display can be dimmed and reactiva- > The screen will go dark (the climate bar There are five different basic views in the center
ted using the home button under the screen. will remain visible). All functions con- display: Home view, Top view, Climate view, App
nected to the screen continue to operate. view and Function view. The screen is automati-
2. To reactivate the screen, briefly press the cally activated when the driver's door is opened.
Home button.
> The view that was displayed before the Home view
screen was turned off will be displayed Home view is the view displayed when the screen
again. is activated. It consists of four tiles: Navigation,
Media, Phone and a fourth tile.
NOTE An app or vehicle function selected from the App
The screen cannot be turned off when a or Function views will start in the respective tile in
prompt to perform an action is being dis- Home view. For example, FM radio will start in
played on the screen. the Media tile.
Center display's home button. The fourth tile contains the most recently used
When the home button is used, the screen will go app or vehicle function that is not related to the
NOTE other three tiles.
dark and the touchscreen no longer reacts to
touch. The climate bar will remain visible. All func- The center display is turned off automatically
The tiles display brief information about the
tions connected to the screen continue to oper- when the engine is off and the driver's door is
respective apps.
ate, such as climate, audio, guiding* and apps. opened.
The center display screen can be cleaned when
NOTE
the display is dimmed. The dimming function can Related information
also be used to darken the screen so it is not a • Cleaning the center display (p. 615) When the vehicle is started, information on
distraction while driving. the current status of apps will be displayed in
• Changing the appearance of the center dis- the respective tile in Home view.
play (p. 133)
• Center display overview (p. 111)
}}
* Option/accessory. 117
DISPLAYS AND VOICE CONTROL
118 * Option/accessory.
DISPLAYS AND VOICE CONTROL
App view Tap an app to open it. It will then be opened in its Function view
associated tile, e.g. Media.
Depending on the number of apps, it is possible
to scroll down in the App view. This is done by
sweeping/dragging from the bottom upwards.
To return to Home view, swipe the screen from
left to right10 or press the Home button.
App view showing the vehicle's apps. Function view with buttons for various vehicle functions.
10 Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction. }}
* Option/accessory. 119
DISPLAYS AND VOICE CONTROL
Related information
• Handling tiles in the center display (p. 121)
• Symbols in the center display status bar
(p. 126)
• Opening settings in the center display
(p. 134)
• Opening contextual setting in the center dis-
play (p. 135)
• Owner's Manual in the center display (p. 17)
• Driver profiles (p. 139)
• Climate system controls (p. 217)
• Apps (p. 465)
• Function view in the center display (p. 124)
• Center display overview (p. 111)
10 Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction.
120
DISPLAYS AND VOICE CONTROL
}}
121
DISPLAYS AND VOICE CONTROL
122
DISPLAYS AND VOICE CONTROL
11 Does not apply to all apps or vehicle functions opened via the fourth tile
123
DISPLAYS AND VOICE CONTROL
Function view in the center display to Function view by swiping from left to right Different types of buttons
Function view, which is one of the center dis- over the screen12. There are three different types of buttons for
play's basic views, contains all of the vehicle's vehicle functions; see below:
function buttons. From the Home view, navigate
12 Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction.
124
DISPLAYS AND VOICE CONTROL
Button modes
Related information
• Handling the center display (p. 114)
• Navigating in the center display's views
(p. 117)
125
DISPLAYS AND VOICE CONTROL
Moving apps and buttons in the NOTE Symbols in the center display status
center display bar
Hide the apps that are rarely or never used by
The apps and buttons for vehicle functions can Overview of symbols displayed in the center dis-
moving them far down, outside of the visible
be moved and organized in the App and Func- play status bar.
view. This makes it easier to find the apps
tion views.
used more frequently. The status bar shows current vehicle activities
1. Swipe from right to left13 to access App view
and in certain cases, also their status. Due to the
or swipe from left to right13 to access Func-
limited space in the status bar, not all symbols
tion view. NOTE will be displayed at all times.
2. Press and hold an app or button. Apps and vehicle function buttons cannot be
> The app or button will change size and situated at spots already in use. Symbol Meaning
become slightly transparent. It can then
be moved. Connected to the Internet.
Related information
3. Drag the app or button to an available posi- • Function view in the center display (p. 124)
Could not connect to Internet.
tion in the view. • Apps (p. 465)
A maximum of 48 rows can be used to position • Handling the center display (p. 114) Roaming activated.
apps or buttons. To move an app or button out-
side the visible view, drag it to the bottom of the Cell phone network signal strength.
view. New rows will be added and the app or but-
ton can be placed in one of these. Bluetooth device connected.
Apps or buttons placed below the view's normal
display will not be visible on the screen. Bluetooth activated but no device
connected.
Swipe the screen to scroll up or down in the view
to display information outside the view. Information sent to and from GPS.
13 Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction.
126
DISPLAYS AND VOICE CONTROL
Action in progress.
Clock.
127
DISPLAYS AND VOICE CONTROL
NOTE
The keyboard cannot be used while the vehi-
cle is moving.
128
DISPLAYS AND VOICE CONTROL
The illustration shows an overview of some of the buttons that may be shown on the keyboard. The appearance may vary depending on language settings and the context in which
the keyboard is used.
}}
129
DISPLAYS AND VOICE CONTROL
|| Row showing suggestions for words or char- uppercase letter. In text fields intended for Variants of letters or characters
acters14. The suggested words change as passwords, website addresses or email
new letters are entered. Scroll through the addresses, all letters will automatically be
list of suggested words by tapping the right lowercase unless uppercase is selected.
or left arrows. Tap a suggestion to select it. Used to enter numbers. The number key-
Please note that this function is not available
board (2) will then be displayed. Tap ,
in all languages. When unavailable, this row
will not be shown on the keyboard. which is shown instead of in number
mode, to return to the keyboard with letters,
Available characters are adapted to the lan-
or to display the keyboard with special
guage selected for the keyboard (see num-
characters.
ber 7 below). Tap a character to enter it.
Used to change the keyboard language, e.g.
Different buttons are displayed here depend-
EN. The available characters and word sug-
ing on the context in which the keyboard is
gestions (1) vary depending on the selected
used, e.g. @ to enter an email address or the Variants of a letter or character, e.g. é or è, can
language. In order to toggle between key-
return key to start a new line. be entered by pressing and holding the letter or
board languages, the languages must first be
This button hides the keyboard. In cases added under Settings. character. A box containing possible variants of
where this is not possible, the button will not the letter or character will appear. Tap the
Space bar. desired variant. If no variant is selected, the origi-
be displayed.
nal letter/character will be used.
Used to enter uppercase letters. Tap once to Delete. Tap to delete characters one at a
enter one uppercase letter and then con- time. Press and hold to delete multiple char- Related information
tinue with lowercase letters. Tap twice for acters quickly.
• Changing keyboard language in the center
caps lock (all text will be entered in upper- Used to change to handwriting mode. display (p. 131)
case letters). Tap again to return the key-
board to lowercase letters. In this mode, the Tap the confirm button over the keyboard (not • Entering characters, letters and words by
shown in illustration) once to confirm the text that hand in the center display (p. 131)
first letter after a period, exclamation point or
question mark will be automatically entered has been entered. The button's appearance dif- • Handling the center display (p. 114)
in uppercase form. The first letter entered in fers depending on the context.
• Handling text messages (p. 504)
text fields will also be uppercase. In text
fields intended for names or addresses, each
word will be automatically started with an
130
DISPLAYS AND VOICE CONTROL
Changing keyboard language in the To toggle between keyboard languages from the Entering characters, letters and
center display list: words by hand in the center display
In order to toggle between keyboard languages, 1. Press and hold the button. Characters, letters and words can be entered in
the languages must first be added under > A list will appear. the center display by handwriting them on the
Settings. touchscreen.
2. Select the desired language. If more than Tap the button on the center
Adding or deleting languages in four languages have been selected under display's keyboard to switch
Settings Settings, you can scroll through the list from the keyboard to handwrit-
The keyboard is automatically set to the same shown on the keyboard. ing mode.
language as the system language. The keyboard > The keyboard and word suggestions will
language can be manually changed without be adapted to the selected language.
affecting the system language.
To change keyboard language without displaying
1. Tap Settings in Top view. the list:
2. Tap System System Languages and – Tap the button.
Units Keyboard Layouts. > The keyboard layout will change to the
next language in the list without display-
3. Select one or more languages in the list.
ing the list.
> It is now possible to toggle between the
selected languages using the keyboard. Related information
If no language has been selected under • Changing system language (p. 134)
Settings, the keyboard will remain in the same • Using the center display keyboard (p. 128)
language as the vehicle's system language.
131
DISPLAYS AND VOICE CONTROL
|| Space bar. Blank spaces can be created by Handwriting characters/letters/words Erasing/changing handwritten characters/
writing a dash (‒) in the field for handwritten 1. Write a character, a letter, a word or parts of letters
letters (1). See "Writing blank spaces in free- a word in the field for handwritten letters (1).
text fields" below. Write the word or part of the word vertically
Delete. Tap once to erase one character/ or horizontally.
letter at a time. Wait a moment before tap- > A number of suggestions for characters,
ping again to erase the next character, letter letters or words will be displayed (3). The
etc. most likely will be shown at the top of the
Return to the standard keyboard layout. list.
132
DISPLAYS AND VOICE CONTROL
New lines in free-text fields in handwriting Changing the appearance of the Turning off and adjusting the
mode center display volume of the center display system
The appearance of the center display can be sounds
changed by selecting a different theme. The volume of the center display system sounds
1. Tap Settings in the Top view. can be adjusted or turned off completely.
1. Tap Settings in the Top view in the center
2. Tap My Car Displays Display display.
Themes.
2. Tap Sound System Volumes.
3. Select a theme, e.g. Minimalistic or
Chrome Rings. 3. Pull the control under Touch Sounds to
adjust the volume or turn off screen tap
In addition to these themes, you can also choose
Create a new line by drawing above the characters in sounds. Pull the control to the desired sound
between Normal and Bright. In Normal, the
the handwriting field as shown in the illustration17. level.
background of the screen is dark and the text is
Writing blank spaces in free-text fields light. This option is the default setting for all Related information
themes. If the bright version is selected, the
• Center display overview (p. 111)
background will be light and the text will be dark.
This option can, for example, make the screen • Changing settings in the center display
easier to see in bright daylight conditions. (p. 136)
These alternatives are always available for selec- • Sound settings (p. 464)
tion and are not affected by the ambient lighting.
Related information
• Opening settings in the center display
Make a blank space by drawing a line from left to right18. (p. 134)
Related information • Activating and deactivating the center display
• Using the center display keyboard (p. 128) (p. 117)
• Cleaning the center display (p. 615)
17 For Arabic keyboards, draw the same character, but in mirror image.
18 For Arabic keyboards, draw the line from right to left.
133
DISPLAYS AND VOICE CONTROL
Changing system units of Changing system language Opening settings in the center
measurement Language settings are adjusted in the Settings display
Unit settings are adjusted in the Settings menu menu in the center display. The center display is used to manage Settings
in the center display. NOTE and to display information for many of the vehi-
cle's functions.
1. Tap Settings in the Top view in the center Changing languages in the center display
display. could mean that certain owner's information
will not comply with national or local laws and
2. Proceed to System System Languages regulations. Do not change to a language that
and Units Units of Measurement. you do not fully understand, as this could
3. Select one of the following measurement make it difficult to navigate back through the
standards: menu.
134
DISPLAYS AND VOICE CONTROL
Related information Opening contextual setting in the Most of the vehicle's basic apps have this contex-
• Center display overview (p. 111) center display tual setting option, but not all.
• Changing settings in the center display Most of the settings for the vehicle's basic apps
Third-party apps
(p. 136) can be changed directly in Top view in the cen-
Third-party apps are apps that are not factory-
ter display via contextual settings.
• Setting types in the center display (p. 137) installed in the vehicle's system, but can be
• Table of settings in the center display downloaded, e.g. Volvo ID. Settings for these
(p. 138) apps are changed in the apps themselves, not in
Top view.
Related information
• Opening settings in the center display
(p. 134)
• Center display overview (p. 111)
• Resetting center display settings (p. 137)
• Download apps (p. 466)
135
DISPLAYS AND VOICE CONTROL
Changing settings in the center Related information Resetting user data when the
display • Center display overview (p. 111) vehicle changes owners
You can change Settings and information for • Resetting center display settings (p. 137) If the vehicle changes owners, all user data and
many of the vehicle's functions via the center system settings should be reset to factory
display.
• Setting types in the center display (p. 137)
defaults.
1. Open Top view by tapping the tab or by drag- • Table of settings in the center display
ging/swiping from the top of the screen (p. 138) Vehicle settings can be reset at different levels.
downward. Reset all user data and system settings to their
original factory defaults when the vehicle
2. Tap Settings to open the Settings menu. changes owner. It is also important to change the
3. Tap one of the categories and sub-catego- owner of the Volvo On Call service.
ries to navigate to the desired setting.
Related information
4. Change the setting(s). Different types of set- • Resetting center display settings (p. 137)
tings are changed in different ways.
> Changes are saved immediately.
136
DISPLAYS AND VOICE CONTROL
Resetting center display settings 4. Tap OK to confirm the reset. Setting types in the center display
All settings made in the center display's Settings For Reset Personal Settings, confirm the Different types of settings are changed in differ-
menu can be reset to default values. reset by tapping Reset for the active ent ways. Refer to the table below for a descrip-
profile or Reset for all profiles. tion of the different types of settings.
Two types of reset
There are two ways to reset the settings in the > The selected settings will be reset. Types of settings
Settings menu:
Related information Type of Description
• Factory Reset- erases all data and files and • Center display overview (p. 111) setting
resets all settings to factory default.
• Opening settings in the center display Trigger Starts an app or a separate view
• Reset Personal Settings- erases personal (p. 134) function for more advanced settings. Tap
data and resets personalized settings to fac-
• Changing settings in the center display the text to e.g. connect a
tory default. (p. 136) Bluetooth® device.
Resetting settings • Table of settings in the center display Radio but- Select one of the possible set-
Follow these instructions to reset the settings. (p. 138) ton tings by tapping the desired radio
button to e.g. change the system
NOTE language.
Factory Reset is only possible when the Multi- Select a level for a particular set-
vehicle is stationary. selection ting by pressing the desired part
button of the button, e.g. to select sensi-
1. Tap Settings in the Top view in the center tivity level for City Safety.
display. Checkbox Tap the checkbox to activate/
2. Proceed to System Factory Reset. deactivate a function, e.g. to
select automatic start for heated
3. Select the type of reset you would like to do. seats.
> A pop-up window will appear.
}}
137
DISPLAYS AND VOICE CONTROL
138 * Option/accessory.
DISPLAYS AND VOICE CONTROL
Climate
The Climate main category does not have any
sub-categories.
}}
* Option/accessory. 139
DISPLAYS AND VOICE CONTROL
140
DISPLAYS AND VOICE CONTROL
Changing a driver profile's name Resetting driver profile settings Linking a remote key to a driver
It is possible to change the names of the differ- Settings that have been saved for one or more profile
ent driver profiles used in the vehicle. driver profiles can be reset when the vehicle is A remote key can be linked to a driver profile.
1. Tap Settings in the Top view in the center stationary. This driver profile and all of its settings will then
display. NOTE automatically be selected every time the vehicle
is used with that particular remote key.
2. Tap System Driver Profiles. Factory Reset is only possible when the
3. Select Edit Profile. vehicle is stationary. The first time the remote key is used, it is not
linked to any specific driver profile. The Guest
> A menu will open in which the driver pro- profile is automatically activated when the ignition
file can be changed. 1. Tap Settings in the Top view.
is switched on.
4. Tap the Profile Name box. 2. Tap System Factory Reset Reset A driver profile can also be selected manually
> A keyboard will be displayed and can be Personal Settings. without linking it to any key. When the vehicle is
used to change the name. Tap to 3. Select option Reset for the active profile, unlocked, the last active driver profile will be acti-
close the keyboard. Reset for all profiles or Cancel. vated. If the key has ever been linked to a driver
profile, it is not necessary to manually select a
5. Save the name change by pressing Back or Related information driver profile when using that particular key.
Close.
• Driver profiles (p. 139)
> The name has now been changed. Linking a remote key to a specific driver
• Resetting center display settings (p. 137)
profile
NOTE First select the profile you would like to link to
Profile names may not begin with a space. If a the key (if that profile is not already active). The
space is entered first, the profile name will not active profile can then be linked to the key.
be saved. 1. Tap Settings in the Top view in the center
display.
Related information
2. Tap System Driver Profiles.
• Selecting a driver profile (p. 140)
• Using the center display keyboard (p. 128) 3. Mark the desired profile. The display will
return to Home view. The Guest profile can-
not be linked to a remote key.
}}
141
DISPLAYS AND VOICE CONTROL
|| 4. Pull down Top view again and tap Settings • Remote key (p. 237) Messages in the center display
System Driver Profiles Edit The center display shows messages in certain
Profile. circumstances to inform or assist the driver.
5. Select Connect key to link the profile with
the key. A driver profile can only be linked to
the key currently being used in the vehicle. If
there are any other keys in the vehicle, More
than one key is found, put the key you
want to connect on backup reader will be
displayed.
Related information
• Driver profiles (p. 139)
• Changing a driver profile's name (p. 141)
142
DISPLAYS AND VOICE CONTROL
Pop-up messages Handling messages in the center For messages without buttons:
Messages are sometimes shown as pop-up win- display – Close the message by tapping it or let the
dows. Pop-up messages have a higher priority Messages in the center display are handled in message automatically time-out after a short
than messages shown in the status bar and the center display's views. period.
require acknowledgment/action before they dis-
> The message will disappear from the sta-
appear. Messages that need to be saved are
tus bar.
stored in Top view in the center display.
Messages that need to be saved are stored in
Related information Top view in the center display.
• Handling messages in the center display
(p. 143) Related information
• Handling messages saved from the center • Messages in the center display (p. 142)
display (p. 144) • Handling messages saved from the center
• Messages in the instrument panel (p. 106) display (p. 144)
• Messages in the instrument panel (p. 106)
143
DISPLAYS AND VOICE CONTROL
Handling messages saved from the Handling saved messages Head-up display*
center display Some messages have a button to e.g. activate/ The head-up display is a complement to the
Messages saved from the instrument panel and deactivate a function related to the message. instrument panel and projects information from
center displays are handled in the center display. – Tap the button to perform the action. the instrument panel onto the windshield. The
projected images can only be seen from the driv-
Saved messages in Top view are automatically er's seat.
deleted when the ignition is switched off.
Related information
• Messages in the center display (p. 142)
• Handling messages in the center display
(p. 143)
• Messages in the instrument panel (p. 106)
144 * Option/accessory.
DISPLAYS AND VOICE CONTROL
NOTE NOTE
The driver's ability to see information in the People with certain types of vision problems
head-up display may be impeded by: may experience headaches or eye strain
when using the head-up display.
• the use of polarizing sunglasses
• a driving posture in which the driver is not
centered in the seat City Safety in head-up-display
If City Safety is activated, the information in the
• objects on the display unit's glass cover head-up display will be replaced by a City Safety
• unfavorable lighting conditions. graphic. This graphic will illuminate even if the
head-up display is turned off.
CAUTION Examples of what might be shown on the display.
The information is projected from a display Speed
unit located in the dashboard. To help prevent
damage to the display unit's glass cover, do Cruise control
not place any objects on the glass and pre-
vent objects from falling onto it. Navigation
Road signs
A number of symbols may be projected temporar-
ily onto the head-up display, including:
If the warning symbol appears, read the
warning message in the instrument A City Safety graphic flashes to attract the driver's atten-
panel. tion.
* Option/accessory. 145
DISPLAYS AND VOICE CONTROL
Activating and deactivating the Head-up display settings* Adjusting brightness and height
head-up display* Adjusting settings for the head-up display. position
The head-up display can be activated and deac- Settings can be adjusted in the center display's
tivated when the vehicle has been started. Settings menu when the vehicle is started and a
projected image is displayed on the windshield.
Press the Head-up Display
button in the center display's This setting is stored as a personal setting in the
Function view. An indicator light driver profile.
in the button will illuminate
Selecting display options 1. Press the Head-up Display Adjustments
when the function is activated.
Select the functions to be shown in the head-up button in the center display's Function view.
display.
2. Adjust the brightness of the projected image
Related information 1. Tap Settings in the center display's Top and the height position in the driver's field of
• Head-up display settings* (p. 146) view. vision using the right-side steering wheel
• Head-up display* (p. 144) lever.
2. Tap My Car Displays Head-Up
Display Options.
3. Select one or more functions:
• Show Navigation
• Show Road Sign Information
• Show Driver Support
• Show Phone.
Decreasing brightness
Increasing brightness
Raising position
146 * Option/accessory.
DISPLAYS AND VOICE CONTROL
Display Options Head-Up Display • Activating and deactivating the head-up dis-
Calibration. play* (p. 146)
* Option/accessory. 147
DISPLAYS AND VOICE CONTROL
|| Voice control is carried out as a dialog, with spo- Using voice commands20 Voice command examples
ken commands from the user and verbal respon- Press the button for voice con- Press , say "Call [First name] [Last name]
ses from the system. The voice control system [number category]" - calls the selected contact
trol on the right-side
uses the same microphone as devices connected from the phone book. If the contact has several
steering wheel keypad to acti-
with Bluetooth, and the voice control system phone numbers (e.g. home, cell, work), the right
vate the system and initiate a
responds through the vehicle's loudspeakers. In category must also be given.
voice command dialog.
certain cases, text messages will also be dis-
played in the instrument panel. The functions are Press and say "Call Robyn Smith
controlled using the right-side steering wheel These may include: cellular".
keypad and settings are made in the center dis-
play.
• Wait until after the tone, and then speak in Commands/phrases
your normal voice at a normal speed. The following commands can always be used:
System updates • Do not speak while the system is responding
The voice control system is continuously (the system is unable to process commands
• "Repeat" - repeats the most recent voice
improved. For optimal functionality, always down- command in the current dialog.
during this time).
load the latest update at support.volvocars.com. • "Cancel" - cancels the dialog.
• Avoid background noises in the passenger
Related information compartment by keeping doors, windows and • "Help" - initiates a help dialog. The system
responds with commands that can be used
• Using voice commands (p. 148) the panoramic roof* closed.
in the current situation, an instruction or an
• Voice control for cellular phones (p. 149) Voice control can be canceled by:
example.
• Voice control for radio and media (p. 150) • saying "Cancel". Commands for specific functions, such as phone
• Climate control system voice commands • pressing and holding the steering wheel key- and audio, are described in the sections related
(p. 208) pad's voice command button . to that function.
• Voice control settings (p. 150) To speed up the voice command dialog and skip
system responses, press the voice command but-
ton while the system is responding and give
your next command.
148 * Option/accessory.
DISPLAYS AND VOICE CONTROL
• Frequencies can be given as ninety-eight • "Call [phone number]" - call a phone num-
point eight (98.8), one hundred four point ber.
two, or hundred four point two (104.2). • "Recent calls" - display the list of recent
calls.
Related information
• Voice control (p. 147) • "Read message" - read a text message
aloud. If there are several messages, select
• Voice control for cellular phones (p. 149) the message to read aloud.
• Voice control for radio and media (p. 150) • "Message to [contact]" - the user is
• Climate control system voice commands prompted to dictate a short message. The
(p. 208) message will then be read aloud and the
• Voice control settings (p. 150) user can choose to send22 or re-dictate the
message. The vehicle must be connected to
the Internet to access this function.
* Option/accessory. 149
DISPLAYS AND VOICE CONTROL
Voice control for radio and media23 • "USB" - starts playback from USB. Voice control settings24
Voice commands for the radio and media play- • "iPod" - starts playback from iPod. Settings for the voice control system are made
ers are shown below. • "Bluetooth" - starts playback from a Blue- here.
Tap and say one of the following commands: tooth-connected media source. Settings System Voice Control
• "Media" - initiates a dialog for media and • "Similar music" - plays music from a USB-
radio and displays examples of commands. connected device with music similar to that Settings can be personalized in the following
currently playing. areas:
• "Play [artist]" - plays music by the selected
artist. Related information • Repeat Voice Command
• "Play [song title]" - plays the selected • Voice control (p. 147) • Gender
song. • Speech Rate
• Using voice commands (p. 148)
• "Play [song title] from [album]" - plays
• Voice control for cellular phones (p. 149)
the selected song from the selected album. Sound settings
• Climate control system voice commands Select sound settings under:
• "Play [radio station]" - starts the selected (p. 208)
radio station. Settings Sound System Volumes
• Voice control settings (p. 150)
• "Tune to [frequency]" - tunes to the Voice Control
selected radio frequency in the currently
active waveband. If no radio source is active, Language settings
the FM band will be started as default. The voice control system is not available for all
• "Tune to [frequency] [waveband]" - tunes languages. The languages available for voice
to the selected radio frequency on the commands are indicated by the icon in the
selected waveband. list of languages.
• "Radio" - starts FM radio. Changing the language here will also change the
• "Radio FM" - starts FM radio. language in the menus, messages and help texts.
• "Radio AM" - starts AM radio.
Settings System System Languages
• "SiriusXM" - starts SiriusXM radio* and Units System Language
• "CD" - starts playback from CD*.
150 * Option/accessory.
DISPLAYS AND VOICE CONTROL
Related information
• Voice control (p. 147)
• Using voice commands (p. 148)
• Voice control for cellular phones (p. 149)
• Climate control system voice commands
(p. 208)
• Voice control for radio and media (p. 150)
• Sound settings (p. 464)
• Changing system language (p. 134)
151
LIGHTING
LIGHTING
154 * Option/accessory.
LIGHTING
WARNING • Using turn signals (p. 160) Adjusting light functions via the
• Using high beam (p. 158) center display
The vehicle lighting system cannot in all situa-
Multiple light functions can be adjusted and acti-
tions determine when the daylight is too weak • Low beams (p. 157)
or not strong enough, e.g. when there is fog vated via the center display. These include auto-
or rain. • Front fog lights/cornering illumination* matic high beam, home safe lighting, and
(p. 161) approach lighting.
The driver is always responsible for driving the
vehicle with lighting that is safe for the traffic • Rear fog light (p. 162) 1. Tap Settings in the Top view.
conditions and as specified by applicable traf- • Active Bending Lights* (p. 161) 2. Tap My Car Lights and Lighting.
fic regulations.
• Brake lights (p. 163)
3. Select Exterior Lights or Interior Lighting.
Thumbwheel in instrument panel • Emergency brake lights (p. 163)
• Hazard warning flashers (p. 164) Related information
• Lighting panel and controls (p. 154)
• Active high beam (p. 159)
• Using home safe lighting (p. 164)
• Welcome Light (p. 164)
• Using turn signals (p. 160)
• Opening settings in the center display
(p. 134)
• Function view in the center display (p. 124)
Related information
• Adjusting light functions via the center dis-
play (p. 155)
• Interior Lighting (p. 165)
• Parking lights (p. 156)
* Option/accessory. 155
LIGHTING
Parking lights deactivated. In weak daylight or dark conditions, Daytime running lights
The parking lights can be used to help other the parking lights and low beams will be illumi- The vehicle has sensors that detect ambient
road users see the vehicle if it is stopped or nated. lighting conditions. With the lighting ring in the
parked. Use the lighting ring on the steering In dark conditions, the rear parking lights also position, the daytime running lights will
wheel lever to turn on the parking lights. illuminate when the tailgate is opened to alert fol- always be activated when the ignition is in mode
lowing traffic. This happens regardless of what II or when the engine is running. In weak daylight
position the lighting ring or ignition is in. or dark conditions, the headlights automatically
switch to low beams.
Related information
• Lighting panel and controls (p. 154)
• Ignition modes (p. 407)
• Replacing daytime running lights/front park-
ing light bulbs (p. 596)
156
LIGHTING
With the steering wheel lever's lighting ring in the WARNING Low beams
position, the daytime running lights (DRL1) When driving with the lighting ring in the
The system is an energy saving aid – it cannot
will illuminate when the vehicle is driven in day- in all situations determine when the daylight is position, low beam will be automatically acti-
light conditions. The headlights will switch auto- too weak or not strong enough, e.g. when vated in weak daylight or dark conditions, when
matically from daytime running lights to low there is fog or rain. the ignition is in II position or when the engine is
beams in weak daylight or dark conditions. The running.
The driver is always responsible for driving the
headlights will also switch to low beams if the vehicle with lighting that is safe for the traffic
front fog lights* and/or rear fog light are acti- conditions and as specified by applicable traf-
vated. fic regulations.
US models: When mode is selected, the
daytime running lights can be deactivated in the Related information
center display. The parking lights will also be • Lighting panel and controls (p. 154)
deactivated. In weak daylight or dark conditions, • Ignition modes (p. 407)
the parking lights and low beams will be illumi-
nated.
• Low beams (p. 157)
• Replacing daytime running lights/front park-
In the US: With the lighting ring in the or ing light bulbs (p. 596)
position, the daytime running lights will be
off.
Lighting ring in AUTO position.
In Canada: With the lighting ring in the or
With the lighting ring in the position, the
position, the daytime running lights will be low beams will be automatically activated if:
on.
• the front fog lights* are activated
NOTE • the rear fog light is activated
Volvo recommends use of Daytime Running • the rear and front fog lights are activated.
Lights in the US. Its use is mandatory in Can- With the lighting ring in the position, the
ada. low beams will always be activated when the igni-
tion is in mode II or when the engine is running.
* Option/accessory. 157
LIGHTING
|| Tunnel detection Using high beam wheel lever forward. Deactivate by moving
The vehicle will detect if it enters a tunnel and High beam is operated via the left-hand steering the steering wheel lever backward.
shift from daytime running lights to low beams. wheel lever. High beam is the vehicle's strongest
lighting and should be used when driving in dark When the high beams are activated, the
Note that the left-hand steering wheel lever must
conditions, provided it does not blind other road symbol will be illuminated in the instrument panel.
be in position for tunnel detection to work.
users, to improve visibility.
Related information
Related information • Lighting panel and controls (p. 154)
• Lighting panel and controls (p. 154)
• Active high beam (p. 159)
• Ignition modes (p. 407)
• Replacing the high beam headlight bulbs
• Daytime running lights (p. 156) (p. 595)
• Replacing the low beam headlight bulbs
(p. 595)
High beams
The high beams can be activated when the
lighting ring is in mode 2 or .
Activate high beams by moving the steering
158
LIGHTING
Active high beam This function can be used in dark conditions If this symbol and the message Active
Active high beams is a function that uses cam- when the vehicle's speed is approx. 20 km/h High Beam Temporarily
era sensors in the upper edge of the windshield (approx. 12 mph) or higher. unavailable is displayed in the instru-
to detect the headlights of approaching vehicles If active high beams are deactivated when the ment panel, switching between high
or the taillights of the vehicle directly ahead. high beams are on, the headlights will automati- and low beams must be done manually. The light-
When either of these is detected, the vehicle's cally switch to low beams. ing ring on the steering wheel lever can remain in
headlights will automatically switch from high the position. The symbol will go out
beams to low beams. When active high beams are activated, a white when the message is displayed.
symbol will be displayed in the instrument
panel. The same applies if this symbol along
with the message Windscreen
When high beams are on, the symbol will be blue. sensor Sensor blocked, see
For LED headlights, this applies even if the high Owner's manual is displayed.
beams are partially dimmed, i.e. if the headlights
are illuminated with slightly more than low beams. Active high beams may be temporarily unavailable
in certain situations, e.g. heavy fog or rain. When
Vehicles with halogen headlights active high beams become available again, or the
When the camera sensor no longer detects the windshield sensors are no longer blocked, the
headlights of approaching vehicles or the tail- message will disappear and the symbol will
lights of a vehicle ahead, the headlights will be displayed.
return to high beams after a second or so.
Vehicles with LED3 headlights* WARNING
Active high beam is enabled by moving the lighting ring
If the active high beams are equipped with the
on the steering wheel lever to . Automatic high beam is an aid in using the
auto on/off function4, the headlights will return to best possible light based on prevailing condi-
The function can also detect street lighting. high beams a second or so after the camera sen- tions.
When the camera sensor no longer detects an sor no longer detects the headlights of approach-
The driver is always responsible for manually
approaching vehicle or a vehicle ahead, the head- ing vehicles or the taillights of a vehicle ahead. switching between high and low beam when
lights will return to high beams. Limitations for active high beams traffic situations or weather conditions require
The camera sensor on which the function is this.
based has limitations.
* Option/accessory. 159
LIGHTING
Related information
• Hazard warning flashers (p. 164)
Turn signals. • Adjusting light functions via the center dis-
play (p. 155)
Triple flash indicator
Move the steering wheel lever up or down to • Replacing front turn signal bulbs (p. 597)
the first position and release. The turn sig-
nals will flash three times. This function can
be activated/deactivated in the center dis-
play.
160
LIGHTING
Active Bending Lights* The function is only active in weak daylight or Front fog lights/cornering
Active Bending Lights (ABL) are designed to dark conditions and only when the vehicle is mov- illumination*
help provide maximum illumination in curves and ing and the low beams are on. The front fog lights have a stronger beam than
intersections. Depending on equipment level, low beam, making them particularly effective in
Deactivating/activating the function
vehicles with LED5 headlights* may be equipped The function is activated as the default factory
fog.
with Active Bending Lights. setting and can be activated and deactivated in
the center display's Function view:
Tap the Active Bending
Lights button.
Related information
• Adjusting light functions via the center dis-
play (p. 155) Front fog lights button.
• Front fog lights/cornering illumination* The fog lights can be switched on when the igni-
Headlight pattern with function deactivated (left) and (p. 161)
activated (right). tion is in II mode or when the engine is running
Active Bending Lights follow the movement of and the lighting ring is in position , or
the steering wheel to help provide maximum illu- .
mination in curves and intersections, improving Tap the button to activate or deactivate the func-
visibility for the driver.
tion. The symbol in the instrument panel
The function is automatically activated when the comes on when the front fog lights are on.
engine is started. If a fault is detected in the sys-
The front fog lights turn off automatically when
tem, the symbol will illuminate in the the start knob is turned clockwise to turn off the
instrument panel and a message will be dis-
played.
* Option/accessory. 161
LIGHTING
|| ignition or when the lighting ring is turned to the • Adjusting light functions via the center dis- Rear fog light
position. play (p. 155) The rear fog light is considerably brighter than
ordinary taillights and should only be used to
NOTE help other road users see the vehicle when visi-
bility is reduced by conditions such as fog,
Regulations concerning fog light use vary snow, smoke or dust.
from country to country.
Cornering illumination*
The front fog lamps can include the cornering
lights function, which temporarily illuminates the
area diagonally in front of the car in the direction
the steering wheel is turned on a sharp bend, or
in the direction shown by the direction indicators.
The function is activated in weak daylight or dark
conditions when the lighting ring is in or
mode and the vehicle speed is less than
about 30 km/h (about 20 mph).
Rear fog light button.
Both cornering illumination are also illuminated
as a complement to the taillights when reversing. The rear fog light consists of a light on the rear
of the vehicle on the driver's side.
The function is activated as the default factory
setting and can be activated and deactivated The rear fog light can only be used when:
using the center display. • the ignition is in II mode or when the engine
is running and the lighting ring is in position
Related information
• Lighting panel and controls (p. 154) or .
• Ignition modes (p. 407) • the lighting ring is in the position and
the front fog lights are on.
• Rear fog light (p. 162)
• Active Bending Lights* (p. 161)
162 * Option/accessory.
LIGHTING
Press the button for On/Off. The symbol in Brake lights Emergency brake lights
the instrument panel illuminates when the rear The brake lights are automatically illuminated The emergency brake lights are activated to
fog light is on. when braking. warn following vehicles of hard braking.
The rear fog light turns off automatically when: The brake lights illuminate when the brake pedal This function causes an additional taillight on
each side of the vehicle to illuminate.
• the start knob is turned clockwise to turn off is depressed. They also illuminate when the
The emergency brake lights are activated in the
the ignition or when the lighting ring is brakes are automatically applied by one of the
driver support systems. event of hard braking or if the ABS system is
turned to the position. activated and the vehicle is traveling at a high
• the lighting ring is in the position and Related information speed.
the front fog lights are turned off. • Emergency brake lights (p. 163)
After the driver decelerates to a low speed and
• Brake functions (p. 408) then releases the brake, the brake lights resume
NOTE their normal brightness.
Regulations concerning rear fog light use vary
Related information
from country to country.
• Brake lights (p. 163)
• Brakes (p. 409)
Related information
• Lighting panel and controls (p. 154) • Hazard warning flashers (p. 164)
* Option/accessory. 163
LIGHTING
Related information
• Emergency brake lights (p. 163)
• Using turn signals (p. 160)
164 * Option/accessory.
LIGHTING
}}
165
LIGHTING
|| Glove compartment lighting ing is on when the engine is running. Mood light-
The glove compartment lighting comes on or ing can be adjusted in the center display and also
goes off when the glove compartment is opened fine-tuned using the thumb wheel in the dash-
or closed. board.
6 There are also reading lights over the third row of seats*.
7 Does not apply to the third row of seats*.
166 * Option/accessory.
LIGHTING
* Option/accessory. 167
WINDOWS, GLASS AND MIRRORS
WINDOWS, GLASS AND MIRRORS
Windows, glass and mirrors • Using the windshield and headlight washers Pinch protection for windows and
The vehicle is equipped with controls for win- (p. 183) sun curtains
dows, glass and mirrors. Some of the windows • Activating and deactivating the heated wind- All windows and sun curtains* that are controlled
in the car are laminated. shield* (p. 226) electrically have a pinch protection function that
is triggered if anything blocks them while they
Laminated glass • Activating and deactivating the heated rear
window and door mirrors (p. 227) are opening or closing.
The windshield and panoramic roof* have lamina- If pinch protection is activated, movement will
ted glass. The glass is reinforced, which provides stop and then retract automatically to approx.
better protection against break-ins and improved 50 mm (2 inches) from the point at which it was
soundproofing in the passenger compartment. blocked (or to full ventilation position).
Laminated glass is available as an option for
some other glass surfaces. If pinch protection has been triggered, it is still
possible to operate the window or sun curtain
once more in the same direction without pinch
protection, if this is done within 10 seconds after
pinch protection has been triggered. It is thus still
The symbol shows the windows containing laminated possible to override pinch protection when clos-
glass1 ing is interrupted (e.g. due to ice) by pressing and
holding down the control until the window or sun
Related information curtain is fully closed.
• Pinch protection for windows and sun cur-
tains (p. 170)
WARNING
• Panoramic roof* (p. 176)
If the starter battery is disconnected, the func-
• Power windows (p. 171) tion for automatic opening and closing must
• Rearview/door mirrors (p. 173) be reset to function correctly. A reset is
required in order for the pinch protection to
• Using sun curtains* (p. 173) work.
• Head-up display* (p. 144)
• Using the windshield wipers (p. 180)
1 Does not apply to windshield and panoramic roof*, which are always laminated and therefore do not have this symbol.
170 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
* Option/accessory. 171
WINDOWS, GLASS AND MIRRORS
172 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
NOTE WARNING
The windows cannot be opened at speeds The door mirror on the passenger side is
over approx. 180 km/h (ca112 mph), but they curved to improve visibility. Objects in the mir-
ror may appear farther away than they actually
can be closed. are.
The driver is always responsible for following The illustration is generic – the design may vary.
applicable traffic regulations. Hook with locking mechanism The joystick in the drivers' door control panel is
used to adjust the position of the door mirrors.
– Pull up the sun curtain and hook it to the There are also several automatic settings that
Related information
upper section of the door frame. can also be connected to the memory function
• Power windows (p. 171)
The window can be opened and closed when the buttons for the power seat*.
• Pinch protection for windows and sun cur-
tains (p. 170) sun curtain is being used.
Related information
• Reset procedure for pinch protection Related information • HomeLink®* (p. 456)
(p. 171) • Pinch protection for windows and sun cur- • Compass (p. 459)
• Keyless locking and unlocking* (p. 252) tains (p. 170)
• Adjusting the rearview mirror dimming func-
• Locking and unlocking using the remote key • Reset procedure for pinch protection tion (p. 174)
(p. 239) (p. 171)
• Adjusting the door mirrors (p. 175)
• Locking and unlocking from inside the vehi- • Power windows (p. 171)
cle (p. 255)
}}
* Option/accessory. 173
WINDOWS, GLASS AND MIRRORS
• Storing memory settings in power front Adjusting the rearview mirror glare. The forward-pointing sensor monitors
seats* (p. 190) dimming function ambient light, while the rearward-pointing sensor
monitors light from the headlights of following
• Activating and deactivating the heated rear Bright light entering the vehicle from behind, e.g.
window and door mirrors (p. 227) from the headlights of following vehicles, could vehicles.
reflect in the rearview mirror and door mirrors For the door mirrors to be equipped with auto-
and cause a glare. Use the dimming function dim, the rearview mirror must also be equipped
when light from behind is distracting. with auto-dim.
Auto-dim
If bright light enters the vehicle from behind, the NOTE
door mirrors will automatically dim. Auto-dim is If the sensors are obstructed by e.g. a parking
always active when the engine is running, except permit, transponder, sunshade or objects on
when reverse gear is engaged. the seats or in the cargo compartment in a
way that prevents light from reaching the sen-
NOTE sors, the auto-dim function in the door and
rearview mirrors will be reduced.
When the level of sensitivity is changed, this
change will not be noticeable immediately but
will instead take effect after a short period of Related information
time. • Rearview/door mirrors (p. 173)
• Adjusting the door mirrors (p. 175)
The sensitivity level for dimming will affect both
the rearview mirror and door mirrors.
1. Tap Settings in the Top view in the center
display.
2. Tap My Car Mirrors and Convenience.
3. Under Rearview Mirror Auto Dimming,
select Normal, Dark or Light.
The rearview mirror instead has two sensors -
one pointing forward and one pointing rearward -
which work together to identify and eliminate
174 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
Adjusting the door mirrors Resetting the mirrors' position Tilting when parking3
To improve visibility to the rear, the door mirrors A mirror that has been moved out of position The door mirrors can be tilted down to improve
need to be adjusted to the driver's height and manually (e.g. hit or bumped into) must be electri- the driver's view along the sides of the vehicle
seating position. There are several automatic cally returned to its normal position for automatic (e.g. to see the curb while parking).
settings that can also be connected to the mem- folding to function properly.
– Select reverse gear and press the L or R mir-
ory function buttons for the power seat*. 1. Fold in the mirrors by pressing the L and R ror button.
buttons at the same time.
Controls used for door mirrors Please note that the button may need to be
2. Open them again by pressing the L and R pressed twice depending on settings. When the
buttons at the same time. door mirror is tilted down, the light in the button
3. Repeat the above procedure as needed. will flash. When reverse gear is engaged, the
door mirrors will automatically start to move after
The mirrors are now reset to their original posi- 3 seconds and will reach their original position
tions. after about 8 seconds.
Automatically folding door mirrors* Automatically tilting when parking3
The door mirrors can be automatically folded With this setting, the door mirrors will automati-
when driving or parking in tight spaces. cally tilt down when reverse gear is engaged. The
1. Press the L and R buttons at the same time folded position is preset and cannot be adjusted.
(ignition must be in mode I or higher). To immediately return the door mirrors to their
Door mirror controls. original position, press the L or R button twice.
2. Release the buttons after about 1 second.
The joystick in the drivers' door control panel is The mirrors will automatically stop when they 1. Tap Settings in the center display's Top
used to adjust the position of the door mirrors. are completely folded in. view.
1. Press the L button for the left door mirror or Open the mirrors by pressing L and R at the 2. Tap My Car Mirrors and Convenience.
R for the right door mirror. The button will same time. The mirrors will automatically stop
3. Under Exterior Mirror Tilt at Reverse,
light up. when they are completely open.
select Off, Driver, Passenger or Both to
2. Adjust the position using the joystick located activate/deactivate and to select which mir-
between the buttons. ror to tilt.
3. Press the L or R button again. The light in
the button will go out.
3 Only on models equipped with a power driver's seat with memory buttons*. }}
* Option/accessory. 175
WINDOWS, GLASS AND MIRRORS
1. Tap Settings in the center display's Top be moved. • Do not allow children to play with the
view. operating controls.
The panoramic roof has a wind deflector and
sun curtain made of perforated fabric (located • Never leave a child alone in the vehicle.
2. Tap My Car Mirrors and Convenience. beneath the glass sections) for extra protection • Remember to always cut the current to
3. Select Fold Mirror When Locked to acti- in e.g. bright sunlight. the power windows by setting the vehi-
vate/deactivate. cle's electrical system to ignition mode 0
and then taking the remote key with you
Related information when leaving the vehicle.
• Rearview/door mirrors (p. 173)
• Never stick objects or body parts out
• Adjusting the rearview mirror dimming func- through the windows, even if the vehicle
tion (p. 174) electrical system is completely turned off.
• Storing memory settings in power front
seats* (p. 190)
CAUTION
• Activating and deactivating the heated rear
window and door mirrors (p. 227) • Do not open the panoramic roof when
load carriers are installed.
• Never place heavy objects on the panor-
amic roof.
The panoramic roof and sun curtain are operated
using the controls in the ceiling.
It can also be operated using keyless opening* CAUTION
with the door handle. • Remove ice and snow before opening the
To operate the panoramic roof and sun curtain, panoramic roof.
the ignition must be in mode I or II. • Do not operate the panoramic roof if it is
frozen in place.
176 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
4 The comfort position is a position which helps keep wind and resonance sounds to a comfortably low level. }}
* Option/accessory. 177
WINDOWS, GLASS AND MIRRORS
|| direction opposite that of the current direction of Opening and closing ventilation Fully opening and closing the
movement. position panoramic roof with the control in the
The panoramic roof and sun curtain are also ceiling
equipped with pinch protection.
NOTE
For manual opening, the sun curtain must be
completely open before the panoramic roof
can be opened. For the reverse procedure,
the panoramic roof must be completely
closed before the sun curtain can be com-
pletely closed.
178
WINDOWS, GLASS AND MIRRORS
Auto operation • Keyless locking and unlocking* (p. 252) Auto closing the panoramic roof*
1. To open the sun curtain to the fully open • Locking and unlocking using the remote key sun curtain
position, pull the control backward to the (p. 239) With this function, the sun curtain closes auto-
auto open mode and release. matically 15 minutes after the car has been
• Locking and unlocking from inside the vehi-
2. To open the panoramic roof to the comfort cle (p. 255) locked if it is parked in hot weather. This is done
position, pull the control backward a second to lower the passenger compartment tempera-
time to the automatic opening position and ture and protect the upholstery against being
release. bleached by the sun.
The function is deactivated as the default factory
3. To open the panoramic roof fully, pull the setting and can be activated or deactivated using
control backward a third time to the auto- the center display.
matic opening position and release.
1. Tap Settings in the Top view in the center
Close by repeating the above procedure in display.
reverse - push the control forward/down to the
auto close position. 2. Tap My Car Locking.
Automatic operation - rapid opening or Select Auto Close Sunroof Curtain to
closing activate/deactivate.
The panoramic roof and sun curtain can be
opened or closed simultaneously: NOTE
– Open - press the control backward twice to The sun curtain also closes when all windows
the automatic operation position and release. are closed with keyless closing*.
– Close - press the control forward/down twice
to the automatic operation position and
release. Related information
• Panoramic roof* (p. 176)
Related information • Operating the panoramic roof* (p. 177)
• Panoramic roof* (p. 176)
• Pinch protection for windows and sun cur-
• Auto closing the panoramic roof* sun curtain tains (p. 170)
(p. 179)
• Keyless locking and unlocking* (p. 252)
• Pinch protection for windows and sun cur-
tains (p. 170)
}}
* Option/accessory. 179
WINDOWS, GLASS AND MIRRORS
• Locking and unlocking using the remote key Using the windshield wipers Continuous wipers
(p. 239) The windshield wipers clean the windshield. The Move the lever upward for the wipers to
• Locking and unlocking from inside the vehi- right-side steering wheel lever is used to adjust operate at normal speed.
cle (p. 255) windshield wiper settings. Move the lever upward again for the wip-
ers to operate at high speed.
CAUTION
Before activating the wipers, make sure that
the wiper blades are not frozen in place and
that any snow or ice on the windshield and
rear window has been scraped away.
CAUTION
Use plenty of washer fluid when the wipers
clean the windshield. The windshield must be
Right-hand steering wheel lever. wet when the windshield wipers are working.
Thumb wheel, used to set rain sensor sensi-
tivity and interval wiper speed. Related information
Single sweep • Using the rain sensor (p. 181)
Move the lever down and release for a • Using the windshield and headlight washers
single sweep. (p. 183)
180 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
• Filling washer fluid (p. 632) Heated windshield washer nozzles* Using the rain sensor
• Windshield wipers in the service position The washer nozzles are heated automatically in The rain sensor monitors the amount of water on
(p. 631) cold weather to prevent the washer fluid from the windshield and automatically starts the wind-
freezing. shield wipers. Rain sensor sensitivity can be
• Replacing windshield wiper blades (p. 630)
adjusted using the thumb wheel on the right-
• Changing rear window wipers (p. 629) hand steering wheel lever.
Related information
• Using the rain sensor (p. 181)
• Using the windshield and headlight washers
(p. 183)
• Using automatic rear window wiping when
backing up (p. 185)
• Using the rain sensor's memory function
(p. 182)
• Using the rear window wiper/washer
(p. 184)
• Filling washer fluid (p. 632)
• Windshield wipers in the service position
Right-hand steering wheel lever.
(p. 631)
Rain sensor button
• Replacing windshield wiper blades (p. 630)
• Changing rear window wipers (p. 629) Thumb wheel, sensitivity/interval wiper speed
• Using the windshield wipers (p. 180) When the rain sensor is activated, the rain
sensor symbol will be displayed in the instrument
panel.
* Option/accessory. 181
WINDOWS, GLASS AND MIRRORS
|| Activate the rain sensor by pressing the rain sen- Related information Using the rain sensor's memory
sor button . • Using the windshield and headlight washers function
(p. 183) The rain sensor monitors the amount of water on
If the lever is pressed down, the wipers will make
additional sweeps across the windshield. • Using automatic rear window wiping when the windshield and automatically starts the wind-
backing up (p. 185) shield wipers.
Turn the thumb wheel upward for increased sen-
sitivity and downward for decreased sensitivity. • Heated windshield washer nozzles* (p. 181) Activating/deactivating memory
The wipers will make one extra sweep when the • Using the rain sensor's memory function function
thumb wheel is turned upward. (p. 182) The rain sensor's memory function can be set to
• Using the rear window wiper/washer activate so that the rain sensor button does not
Deactivate the rain sensor need to be pressed each time the engine is
(p. 184)
Deactivate the rain sensor by pressing the started:
rain sensor button or moving the lever upward to • Filling washer fluid (p. 632)
1. Tap Settings in the Top view in the center
another wiper mode. • Windshield wipers in the service position
(p. 631) display.
The rain sensor is automatically deactivated in
ignition mode 0 or when the engine is switched • Replacing windshield wiper blades (p. 630) 2. Tap My Car Wipers.
off. • Changing rear window wipers (p. 629) 3. Select Rain Sensor Memory to activate/
The rain sensor is also automatically deactivated • Using the windshield wipers (p. 180) deactivate the memory function.
when the wiper blades are put in the service
Related information
position. The rain sensor will reactivate when
service mode is switched off. • Using the rain sensor (p. 181)
• Using the windshield and headlight washers
(p. 183)
CAUTION
The windshield wipers may start inadvertently • Using automatic rear window wiping when
backing up (p. 185)
and be damaged in automatic car washes.
Deactivate the rain sensor when the engine is • Heated windshield washer nozzles* (p. 181)
running or when the ignition is in mode I or II. • Using the rear window wiper/washer
The symbol in the instrument panel will go (p. 184)
out.
• Filling washer fluid (p. 632)
182 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
• Windshield wipers in the service position Using the windshield and headlight CAUTION
(p. 631) washers
Avoid activating the washer system when it is
• Replacing windshield wiper blades (p. 630) The windshield and headlight washers clean the
frozen or the fluid reservoir is empty. Other-
windshield and headlights. Use the right-side
• Changing rear window wipers (p. 629) wise, there is a risk of damaging the pump.
steering wheel lever to start the windshield and
• Using the windshield wipers (p. 180) headlight washers.
Headlight washer*
Starting the windshield and headlight To save washer fluid, the headlights are washed
washers automatically according to a defined interval
when the headlights are on.
Reduced washing
When there is about 1 liter (1 qt) of washer fluid
left in the reservoir and the Washer fluid Level
low, refill message is displayed in the instrument
panel together with the symbol, the washer
fluid supply to the headlights is cut off. This is to
prioritize windshield cleaning and visibility
through it. The headlights are only washed if high
or low beam is on.
Related information
Washing function, right-hand steering wheel lever.
• Using the rain sensor (p. 181)
– Move the right-hand steering wheel lever
toward the steering wheel to start the wind-
• Using automatic rear window wiping when
backing up (p. 185)
shield and headlight washers.
> After the lever is released, the wipers • Heated windshield washer nozzles* (p. 181)
make several extra sweeps. • Using the rain sensor's memory function
(p. 182)
• Using the rear window wiper/washer
(p. 184)
• Filling washer fluid (p. 632)
}}
* Option/accessory. 183
WINDOWS, GLASS AND MIRRORS
• Windshield wipers in the service position Using the rear window wiper/ – Move the right-side steering wheel lever for-
(p. 631) washer ward to wash/wipe the rear window.
• Replacing windshield wiper blades (p. 630) The rear window wiper/washer cleans the rear
Related information
window. Use the right-side steering wheel lever
• Changing rear window wipers (p. 629) • Using the rain sensor (p. 181)
to start and control the wiper/washer.
• Using the windshield wipers (p. 180) • Using the windshield and headlight washers
Activating the rear window wiper/ (p. 183)
washer • Using automatic rear window wiping when
backing up (p. 185)
NOTE • Heated windshield washer nozzles* (p. 181)
The rear window wiper is equipped with over- • Using the rain sensor's memory function
heating protection that switches off the motor (p. 182)
wiper if it becomes overheated. The rear win-
dow wiper can be operated again after a cool- • Filling washer fluid (p. 632)
ing-down period. • Windshield wipers in the service position
(p. 631)
• Replacing windshield wiper blades (p. 630)
• Changing rear window wipers (p. 629)
• Using the windshield wipers (p. 180)
184 * Option/accessory.
WINDOWS, GLASS AND MIRRORS
Using automatic rear window wiping • Changing rear window wipers (p. 629)
when backing up • Using the windshield wipers (p. 180)
If reverse gear is engaged while the windshield
wipers are on, the rear window wipers will start.
This function is deactivated when a different
gear is selected.
Related information
• Using the rain sensor (p. 181)
• Using the windshield and headlight washers
(p. 183)
• Heated windshield washer nozzles* (p. 181)
• Using the rain sensor's memory function
(p. 182)
• Using the rear window wiper/washer
(p. 184)
• Filling washer fluid (p. 632)
• Windshield wipers in the service position
(p. 631)
• Replacing windshield wiper blades (p. 630)
* Option/accessory. 185
SEATS AND STEERING WHEEL
SEATS AND STEERING WHEEL
Manual front seats Raise/lower the seat by moving the control • Adjusting front seat lumbar support* (p. 194)
up/down.
The power front seats can be adjusted in a num- • Adjusting the passenger seat from the driv-
ber of different ways for optimal comfort and Change the backrest tilt by turning the knob er's seat* (p. 195)
ergonomics. on the backrest.
WARNING
• Do not adjust the seat while driving. The
seat should be adjusted so that the driver
can comfortably reach and operate the
pedals and gear selector.
After adjusting the seat, make sure that it is
securely locked into position before starting
to drive.
Related information
• Power front seats* (p. 189)
Raise/lower the front edge of the seat cush-
• Adjusting the power front seats* (p. 189)
ion* by moving the control up/down.1
• Storing memory settings in power front
Change the length of the seat cushion* by seats* (p. 190)
pulling up the lever and moving the cushion
forward/backward. • Using stored memory in a powered front seat
(p. 191)
Move the seat forward/backing by lifting the
handle and moving the seat to a suitable dis- • Adjusting front seat massage settings*
tance from the steering wheel and pedals. (p. 192)
Check to make sure the seat is securely • Adjusting front seat cushion length (p. 193)
locked into place after its setting has been • Front seat massage settings* (p. 192)
changed.
• Adjusting front seat side bolster settings*
Adjust lumbar support* by pressing the but- (p. 194)
ton up/down/forward/rearward.
188 * Option/accessory.
SEATS AND STEERING WHEEL
Power front seats* • Adjusting front seat side bolster settings* Adjusting the power front seats*
The power front seats can be adjusted in a num- (p. 194) Set the desired sitting position using the control
ber of different ways for optimal comfort and • Adjusting front seat lumbar support* (p. 194) on the front seat's seating section. To activate
ergonomics. The power seats can be moved for- the multifunction control and set the various con-
ward/backward and up/down. The height and
• Adjusting the passenger seat from the driv-
venience functions, turn the control upward/
er's seat* (p. 195)
length* of the seat cushion and the tilt of the downward.
backrest can be adjusted. Lumbar support can
be adjusted up, down, forward and backward.
* Option/accessory. 189
SEATS AND STEERING WHEEL
|| Only one movement (forward/rearward/up/ Storing memory settings in power 2. Press and hold the M button. The indicator
down) can be performed at a time. front seats* light in the button will illuminate.
The front seat backrests cannot be folded down The memory function can be used to store the 3. Within three seconds, press and hold the 1,
completely. settings for the seat, door mirrors and head-up 2 or 3 button.
display*. > When the position has been stored in the
Related information
Three different settings can be stored using the memory button, an audible signal will
• Manual front seats (p. 188)
sound and the indicator light in the M but-
memory function. The memory function controls
• Power front seats* (p. 189)
are located on one or both of the front doors*. ton will go out.
• Storing memory settings in power front If none of the memory buttons are pressed within
seats* (p. 190) three seconds, the M button will go out and no
• Using stored memory in a powered front seat position will be stored.
(p. 191) The seat must be adjusted again before a new
• Adjusting front seat massage settings* memory position can be stored.
(p. 192)
Related information
• Adjusting front seat cushion length (p. 193)
• Manual front seats (p. 188)
• Front seat massage settings* (p. 192)
• Power front seats* (p. 189)
• Adjusting front seat side bolster settings*
• Adjusting the power front seats* (p. 189)
(p. 194)
• Using stored memory in a powered front seat
• Adjusting front seat lumbar support* (p. 194)
(p. 191)
• Adjusting the passenger seat from the driv- Memory button
er's seat* (p. 195)
• Adjusting front seat massage settings*
Memory button (p. 192)
190 * Option/accessory.
SEATS AND STEERING WHEEL
Using stored memory in a powered WARNING • Adjusting front seat lumbar support* (p. 194)
front seat • Adjusting the passenger seat from the driv-
The memory function can be used to store the
• Because the front seats can be adjusted
er's seat* (p. 195)
with the ignition off, children should never
settings for the seat, door mirrors and head-up
be left unattended in the vehicle.
display*.
• Movement of the seat can be STOPPED
Using a stored position at any time by pressing any button on the
A stored position can be used with the front door power seat control panel.
open or closed: • Do not adjust the seat while driving.
Front door open • The seat should be adjusted so that the
– Briefly press one of the memory buttons brake pedal can be depressed fully. In
(1-3). The seat, door mirrors and head-up addition, position the seat as far rearward
display will move and stop at the positions as comfort and control allow.
stored in that button.
• The seat rails on the floor must not be
Front door closed obstructed in any way when the seat is in
– Press and hold one of the memory buttons motion.
(1-3) until the seat, door mirrors and head-
up display stop in the positions stored in that Related information
memory button.
• Manual front seats (p. 188)
If the memory button is released, the seat, door • Power front seats* (p. 189)
mirrors and head-up display will stop moving.
• Adjusting the power front seats* (p. 189)
• Storing memory settings in power front
seats* (p. 190)
• Adjusting front seat massage settings*
(p. 192)
• Adjusting front seat cushion length (p. 193)
• Front seat massage settings* (p. 192)
• Adjusting front seat side bolster settings*
(p. 194)
* Option/accessory. 191
SEATS AND STEERING WHEEL
Front seat massage settings* Restarting the massage function Adjusting front seat massage
The settings can be adjusted using either the The massage function turns off automatically settings*
multifunction control* on the seat or the center after 20 minutes. The function is reactivated The settings for the multifunctional seats can be
display. The adjustment settings are shown in manually. adjusted using either the mutifunction control on
the center display. – Tap Restart, which is displayed in the center the seat or the center display. The adjustment
display, to restart the selected massage pro- settings are shown in the center display*.
gram.
Adjusting front seat massage settings*
> The massage program will restart. If no The front seat backrests have a massage func-
selection is made, the message will be tion. Air-filled cushions provide the massaging
stored in Top view. action and a number of settings are available.
Related information The massage function can only be activated
• Manual front seats (p. 188) when the engine is running.
• Power front seats* (p. 189) 1. Activate the multifunction control by turning
• Adjusting the power front seats* (p. 189) the control upward/downward. The seat set-
tings view will appear in the center display.
• Storing memory settings in power front
Multifunction control, located on the side of the seat seats* (p. 190) 2. Select Massage in the seat settings view.
cushion.
• Using stored memory in a powered front seat 3. Select massage settings by tapping the cen-
Massage settings (p. 191) ter display or by moving the cursor up/down
The following massage settings are available: • Adjusting front seat massage settings* using the multifunction control's upper/lower
(p. 192) buttons. Change a setting in the selected
• On/Off: Select On/Off to turn on/off the function by tapping the arrows on the center
massage function. • Adjusting front seat cushion length (p. 193) display or by using the multifunction control's
• Programs 1-5: There are 5 preset massage • Adjusting front seat side bolster settings* front/rear buttons.
programs. Select Swell, Tread, Advanced, (p. 194)
Lumbar or Shoulder. Related information
• Adjusting front seat lumbar support* (p. 194)
• Manual front seats (p. 188)
• Intensity: Select Low, Normal or High. • Adjusting the passenger seat from the driv-
• Speed: Select Slow, Normal or Fast. er's seat* (p. 195)
• Power front seats* (p. 189)
• Adjusting the power front seats* (p. 189)
192 * Option/accessory.
SEATS AND STEERING WHEEL
• Storing memory settings in power front Adjusting front seat cushion length 2. Select Cushion extension in the seat set-
seats* (p. 190) The settings can be adjusted using either the tings view.
• Using stored memory in a powered front seat multifunction control* on the seat or the center • Push in the front part of the four-way but-
(p. 191) display. The adjustment settings are shown in ton (the round one) to extend the seat
the center display. cushion.
• Adjusting front seat cushion length (p. 193)
• Front seat massage settings* (p. 192) • Press the rear part of the four-way button
to shorten the seat cushion.
• Adjusting front seat side bolster settings*
(p. 194) Related information
• Adjusting front seat lumbar support* (p. 194) • Manual front seats (p. 188)
• Adjusting the passenger seat from the driv- • Power front seats* (p. 189)
er's seat* (p. 195) • Adjusting the power front seats* (p. 189)
• Storing memory settings in power front
seats* (p. 190)
• Using stored memory in a powered front seat
(p. 191)
Multifunction control, located on the side of the seat • Adjusting front seat massage settings*
cushion. (p. 192)
Turn the control up or down to activate the multi- • Front seat massage settings* (p. 192)
function control.
• Adjusting front seat side bolster settings*
Adjusting the seat cushion (p. 194)
The length of the seat cushion can be adjusted • Adjusting front seat lumbar support* (p. 194)
using the multifunction control on the side of the
seat.
• Adjusting the passenger seat from the driv-
er's seat* (p. 195)
1. Activate the multifunction control by turning
the control upward/downward. The seat set-
tings view will appear in the center display.
* Option/accessory. 193
SEATS AND STEERING WHEEL
Adjusting front seat side bolster 2. Select Side bolsters in the seat settings Adjusting front seat lumbar
settings* view. support*
The settings can be adjusted using either the • Press the front part of the four-way button Activate the multifunction control* by turning the
multifunction control* on the seat or the center to increase side bolster support . control upward/downward. The seat settings
display. The adjustment settings are shown in view will appear in the center display.
the center display. • Press the rear part of the four-way button
to decrease side bolster support.
Related information
• Manual front seats (p. 188)
• Power front seats* (p. 189)
• Adjusting the power front seats* (p. 189)
• Storing memory settings in power front
seats* (p. 190)
• Using stored memory in a powered front seat
(p. 191)
• Adjusting front seat massage settings*
(p. 192) Multifunction control, located on the side of the seat
Multifunction control, located on the side of the seat cushion.
cushion. • Adjusting front seat cushion length (p. 193)
Lumbar support can be adjusted in four direc-
The side bolsters in the front seat backrests can • Front seat massage settings* (p. 192) tions by pressing the four-way lumbar support
be inflated/deflated to adjust the amount of sup- • Adjusting front seat lumbar support* (p. 194) button on the side of the seat cushion. The lum-
port provided. • Adjusting the passenger seat from the driv- bar support can be adjusted forward/backward
er's seat* (p. 195) and up/down.
To adjust the side bolsters:
1. Activate the multifunction control by turning Adjusting front seat lumbar support*
the control upward/downward . The seat To adjust the lumbar support:
settings view will appear in the center dis- 1. Activate the multifunction control by turning
play. the control upward/downward. The seat set-
tings view will appear in the center display.
194 * Option/accessory.
SEATS AND STEERING WHEEL
2. Select Lumbar in the seat settings view. Adjusting the passenger seat from
• Press the four-way button (the round but- the driver's seat*
ton) up/down to move the lumbar support The front passenger seat can be adjusted from
upward/downward. the driver's seat.
• Press the front part of the four-way button Activating the function
to increase lumbar support. The function is activated via the function view in
• Press the rear part of the four-way button the center display:
to decrease lumbar support.
Tap the Adjust Passenger
Related information Seat button to activate.
• Manual front seats (p. 188)
• Power front seats* (p. 189) Move the passenger seat forward/rearward
• Adjusting the power front seats* (p. 189) by moving the control forward/rearward.
• Storing memory settings in power front Change the backrest tilt of the passenger
seats* (p. 190) Adjust passenger seat seat by moving the control forward/back-
The driver must adjust the passenger seat within ward.
• Using stored memory in a powered front seat 10 seconds of activating the function. If no
(p. 191) adjustment is made within this time, the function Related information
• Adjusting front seat massage settings* will be deactivated. • Manual front seats (p. 188)
(p. 192)
The driver adjusts the passenger seat using the • Power front seats* (p. 189)
• Adjusting front seat cushion length (p. 193) controls on the driver's seat: • Adjusting the power front seats* (p. 189)
• Front seat massage settings* (p. 192)
• Storing memory settings in power front
• Adjusting front seat side bolster settings* seats* (p. 190)
(p. 194)
• Using stored memory in a powered front seat
• Adjusting the passenger seat from the driv- (p. 191)
er's seat* (p. 195)
• Adjusting front seat massage settings*
(p. 192)
• Adjusting front seat cushion length (p. 193)
• Front seat massage settings* (p. 192)
}}
* Option/accessory. 195
SEATS AND STEERING WHEEL
• Adjusting front seat side bolster settings* Folding the second row backrests CAUTION
(p. 194) The second row of seats has three individual
The seat cushion of the integrated child
• Adjusting front seat lumbar support* (p. 194) seating positions. The backrests can be folded
restraint* must be in the stowed position
down separately.
before the center seat backrest can be folded
down.
WARNING
The armrest* in the center seat must be
• Adjust the seat and ensure it locks into
raised before the seat backrest is folded
position before driving. Use caution when
adjusting the seat. Uncontrolled or care- down.
less adjustments could lead to injury. If the vehicle has private locking*, the ski
• Long objects must always be securely hatch must be closed before the seat back-
tied down to help prevent injury or dam- rest is folded down.
age in the event of sudden braking.
• Always turn off the engine and apply the NOTE
parking brake when loading or unloading
The front seats may need to be pushed for-
the vehicle.
ward and/or the backrest adjusted so that the
• Put the gear selector in P to help prevent rear seat backrests can be fully lowered.
the gear selector from being inadvertently
moved. The rear seats may also need to be moved
rearward.
The seats in the second row must be in the
CAUTION upright position before they can be folded
When the backrest is folded down, make sure down completely. They should not be folded
there are no objects in the rear seat, and the down when they are tilted forward to access
seat belts are not buckled. Otherwise there is the third row of seats.
a risk of damage to the upholstery.
196 * Option/accessory.
SEATS AND STEERING WHEEL
Center seat Outboard seats 2. Make sure that backrest and head restraint
do not come in contact with the seat in front
while the backrest is being folded down. Fold
the backrest down until it locks into position.
> The seat cushion will move downward/
forward when the backrest is folded down
and create a flat surface. The head
restraint folds down automatically when
the backrest is lowered.
WARNING
Make sure the backrest is securely locked
into position after it is folded down.
To fold down the backrest: To fold down the backrest:
1. Fold down the head restraint manually. To return the backrest to the upright position:
NOTE 1. Pull up and hold the handle on the side of
2. Pull the strap on the right side of the center
seat. When folding down a second row seat back- the seat while the backrest is being folded
rest, always start from the seat's normal up.
3. Fold the backrest down until it locks into upright position. Do not use the handle for
position. The seat cushion will move down- 2. Make sure that backrest and head restraint
folding down the seat when the seat is in the do not come in contact with the seat in front
ward/forward when the backrest is folded position for accessing the third row.
down and create a flat surface. while the backrest is being folded up. Fold up
the backrest and release the handle.
To return the backrest to the upright position: 1. Pull up and hold the handle on the side of
3. Press the backrest until it locks into position.
1. Pull the strap. the seat while the backrest is being folded
down. 4. Fold up the head restraint manually.
2. Fold up the backrest and release the strap.
Push the backrest until it locks into position.
3. Adjust the head restraint if necessary.
}}
197
SEATS AND STEERING WHEEL
WARNING
The head restraints on the outboard second-
row seats must always be folded up when
there are passengers in the third row of To lower the restraint, press and hold the button
seats*.
(located between the backrest and the head
restraint, see illustration) while carefully lowering
Related information the head restraint.
• Adjusting the second row head restraints
(p. 198) WARNING
• Moving the second row seats forward/rear- The center seat head restraint must be in its
ward* (p. 199) lowest position when the seat is not occupied.
The center head restraint should be adjusted to When the center seat is occupied, the head
• Adjusting the second row backrest tilt
suit the passenger's height. The entire back of restraint must be correctly adjusted to the
(p. 200) passenger's height, covering the entire back
the head should be covered if possible. Manually
• Getting into and out of the third row of of the head if possible.
move the restraint up or down as needed.
seats* (p. 201)
• Folding the third row backrests* (p. 202)
198 * Option/accessory.
SEATS AND STEERING WHEEL
Electrically folding down the rear seat's WARNING Moving the second row seats
outboard head restraints* forward/rearward*
Do not lower the head restraint if there are
passengers in any of the rear seats. In vehicles with 7 seats*, the seats in the second
row can be moved forward or rearward individu-
ally to help optimize legroom for passengers in
WARNING the second and third rows. The second row
The head restraint must be locked in the seats cannot be moved forward or backward in
upright position after it has been folded up. 5-seat models.
WARNING
The head restraints on the outboard second-
row seats must always be folded up when
there are passengers in the third row of
seats*.
The outer head restraints can be folded via the
center display's function view. The head restraint
can be folded down when the vehicle is in igni-
Related information
tion mode 0. • Folding the second row backrests (p. 196)
}}
* Option/accessory. 199
SEATS AND STEERING WHEEL
200 * Option/accessory.
SEATS AND STEERING WHEEL
* Option/accessory. 201
SEATS AND STEERING WHEEL
Folding the third row backrests* 2. Make sure that backrest and head restraint • Getting into and out of the third row of
The third row has two individual seats. These do not come in contact with the seat in front seats* (p. 201)
can be folded down separately. while the backrest is being folded down. Fold
the backrest down.
CAUTION > The seat cushion will move downward/
forward when the backrest is folded down
To fold down the third-row seat backrests, it
and create a flat surface. The head
may be necessary to change the position/tilt
restraint folds down automatically when
the seats in the second row.
the backrest is lowered.
To return the seat to the upright position, fold the
backrest up manually until it locks into position.
Fold up the head restraint manually.
WARNING
Make sure that the rear seat backrest and
head restraint are locked securely in place
after the seat is folded up.
The head restraints at the outer seats must
always be raised when there is a passenger in
one of these spots of the rear seat.
202 * Option/accessory.
SEATS AND STEERING WHEEL
Steering wheel controls and horn Horn Adjusting the steering wheel
The steering wheel has a horn and controls for The steering wheel can be adjusted to various
e.g. driver support systems and voice control. positions.
Related information
Steering wheel keypads and paddles*. • Adjusting the steering wheel (p. 203) The steering wheel's reach and height can be adjusted.
Driver support system controls2.
WARNING
Paddle* for manually shifting gears (auto-
Adjust the steering wheel and ensure it locks
matic transmission). into position before driving. Never adjust the
Controls for voice commands, adjusting the steering wheel while driving.
head-up display, accessing menus and mes-
sages, and handling phone calls. Steering wheel force can be adjusted with
speed-dependent power steering. Steering wheel
force is adjusted according to the vehicle's speed
to give the driver an enhanced sense of control
and stability.
2 Speed limiter*, Cruise Control, Adaptive Cruise Control*, Distance Alert* and Pilot Assist*. }}
* Option/accessory. 203
SEATS AND STEERING WHEEL
||
Related information
• Steering wheel controls and horn (p. 203)
204
CLIMATE CONTROL
CLIMATE CONTROL
Related information
• Climate zones (p. 206) Climate zones with 4-zone climate system.
• Climate control sensors (p. 207) In 4-zone climate systems, the passenger com-
partment temperature can be set separately for
• Perceived temperature (p. 207)
the left and right sides of the vehicle, and for the
• Climate control system voice commands front and rear seats.
(p. 208) Climate zones with 2-zone climate system.
• Air quality (p. 209) In 2-zone climate systems, the passenger com- Related information
partment temperature can be set separately for • Climate (p. 206)
• Air distribution (p. 212)
the left and right sides of the vehicle.
• Climate system controls (p. 217)
206 * Option/accessory.
CLIMATE CONTROL
Climate control sensors On vehicles equipped with the Interior Air Quality Perceived temperature
The climate system has a number of sensors to System*, there is also an air quality sensor in the The climate control system regulates the climate
help regulate the climate settings in the vehicle. climate system's air intake. in the passenger compartment based on per-
ceived temperature, not actual temperature.
Location of the sensors Related information
• Climate (p. 206) The selected passenger compartment tempera-
• Interior Air Quality System* (p. 210) ture is based on the physical perception of the
current ambient temperature, airflow speed,
humidity, sunlight in the passenger compartment,
etc.
The system has a sunlight sensor that detects
which side of the vehicle the sunlight is shining
on and adjusts the temperature accordingly. This
means that the temperature of the air coming out
of the vents may be different for the left and right
sides, even if the temperature setting is the same
for both sides.
Humidity sensor - in the rearview mirror con-
sole. Related information
• Climate (p. 206)
Ambient temperature sensor - in the right-
side door mirror.
Passenger compartment temperature sensor
- near the buttons in the center console.
Sunlight sensors - on the upper side of the
dashboard.
NOTE
Do not cover or block the sensors with cloth-
ing or other objects.
* Option/accessory. 207
CLIMATE CONTROL
Climate control system voice • "Turn on auto" - activates automatic climate • "Turn on seat ventilation"/"Turn off seat
commands1 control. ventilation" - activates/deactivates seat
Voice commands can be used for the climate • "Air condition on"/"Air condition off" - ventilation*.
control system to e.g. change temperature, acti- activates/deactivates air conditioning. • "Raise seat ventilation"/"Lower seat
vate seat heating* or change blower speed. • "Recirculation on"/"Recirculation off" - ventilation" - raises/lowers the level of seat
Tap and say one of the following commands: activates/deactivates air recirculation. ventilation*.
• "Climate" - starts a command dialog for cli- • "Turn on defroster "/"Turn off defroster" Related information
mate controls and provides examples of - activates/deactivates window and door mir- • Climate (p. 206)
commands that can be used. ror defrosting.
• Voice control (p. 147)
• "Set temperature to X degrees" - sets • "Turn on max defroster"/"Turn off max
desired temperature. defroster" - activates/deactivates max • Using voice commands (p. 148)
defroster. • Voice control settings (p. 150)
• "Raise temperature"/"Lower
temperature" - raises/lowers the set tem- • "Turn on electric defroster"/"Turn off
perature. electric defroster" - activates/deactivates
heated windshield*.
• "Sync temperature" - synchronizes the
temperature for all climate zones in the vehi- • "Turn on rear defroster"/"Turn off rear
cle with the temperature set for the driver's defroster" - Activates/deactivates heated
side. rear window and door mirrors.
• "Air on feet"/"Air on body" - opens the • "Turn steering wheel heat on"/"Turn
desired air vent. steering wheel heat off" - activates/deac-
• "Air on feet off"/"Air on body off" - closes tivates heated steering wheel*.
the desired air vent. • "Raise steering wheel heat"/"Lower
• "Set fan to max"/"Turn off fan" - changes steering wheel heat" - raises/lowers the
blower speed to Max/Off. level of steering wheel heating*.
• "Raise fan speed"/"Lower fan speed" - • "Turn on seat heat"/"Turn off seat heat"
raises/lowers the set blower speed. - activates/deactivates seat heating*.
• "Raise seat heat"/"Lower seat heat" -
raises/lowers the level of seat heating*.
208 * Option/accessory.
CLIMATE CONTROL
Air quality • Passenger compartment air filter (p. 211) Clean Zone*
The materials used in the passenger compart- The Clean Zone function monitors the condi-
ment and air filtering system have been selected tions affecting good air quality in the passenger
to ensure a high level of air quality in the passen- compartment and indicates whether they are ful-
ger compartment. filled or not.
* Option/accessory. 209
CLIMATE CONTROL
|| • The blower is activated. Clean Zone Interior Package* Interior Air Quality System*
• Air recirculation is deactivated. Clean Zone Interior Package (CZIP) is a series Interior Air Quality System (IAQS) is a fully auto-
of modifications that filters even more allergy and matic air quality system that removes gases and
NOTE asthma-inducing substances from the passenger particles to reduce odors and contaminants in
compartment. the passenger compartment.
Clean Zone does not indicate that the air IAQS is part of the Clean Zone Interior Package
quality is good, but only that the conditions for CZIP includes the following: (CZIP) and removes air contaminants such as
good air quality have been met.
• An enhanced function that starts the blower particles, hydrocarbons, nitric oxides and ground-
when the vehicle is unlocked using the level ozone.
Related information remote key. The blower will then fill the pas- If the system's air quality sensors detect contami-
• Air quality (p. 209) senger compartment with fresh air. The func- nants in the outside air, the air intake closes and
tion starts when required and switches off
• Clean Zone Interior Package* (p. 210) air recirculation is activated.
automatically after a period of time or when
• Interior Air Quality System* (p. 210) one of the passenger compartment doors is
NOTE
• Passenger compartment air filter (p. 211) opened. The amount of time the blower runs
gradually decreases due to reduced need up To ensure optimal air quality in the passenger
until the vehicle is 4 years old. compartment, the air quality sensor should
always be engaged.
• The fully automatic Interior Air Quality
System (IAQS). Recirculation is limited in cold weather to pre-
vent fogging.
Related information
• Air quality (p. 209) In the event of fogging, use the defroster
functions for the windshield, side windows
• Clean Zone* (p. 209)
and rear window.
• Interior Air Quality System* (p. 210)
• Passenger compartment air filter (p. 211) Related information
• Activating and deactivating the air quality
sensor* (p. 211)
• Air quality (p. 209)
• Clean Zone* (p. 209)
210 * Option/accessory.
CLIMATE CONTROL
• Clean Zone Interior Package* (p. 210) Activating and deactivating the air Passenger compartment air filter
• Passenger compartment air filter (p. 211) quality sensor* All air entering the passenger compartment
The air quality sensor is part of the fully automa- through the climate control system intake is fil-
ted Interior Air Quality System (IAQS). tered.
The air quality sensor can be switched on or off.
Replacing the passenger compartment
1. Tap Settings in the Top view in the center filter
display. To maintain the high performance of the climate
2. Tap Climate. control system, the filter must be replaced regu-
larly. Follow Volvo's service schedule for recom-
3. Select Air Quality Sensor to activate/deac- mended replacement intervals. When driving in
tivate the air quality sensor. areas with a lot of smog, dust, etc., the filter may
Related information need to be changed more frequently.
• Interior Air Quality System* (p. 210)
NOTE
There are two types of passenger compart-
ment filters. Make sure that the correct filter
is installed.
Related information
• Air quality (p. 209)
• Clean Zone* (p. 209)
• Clean Zone Interior Package* (p. 210)
• Interior Air Quality System* (p. 210)
* Option/accessory. 211
CLIMATE CONTROL
212 * Option/accessory.
CLIMATE CONTROL
Related information Opening, closing and directing air Directing air flow
• Air distribution (p. 212) vents
• Opening, closing and directing air vents Some of the air vents in the passenger compart-
(p. 213) ment can be individually opened, closed and
directed.
• Air distribution options (p. 214)
Misting can be eliminated by directing the outer
air vents towards the door windows.
Direct the outer air vents into the passenger
compartment to maintain a comfortable tempera-
ture in warm weather.
Related information
• Air distribution (p. 212)
• Adjusting air distribution (p. 212)
• Air distribution options (p. 214)
2 The illustration is generic - air vent design varies depending on its location.
213
CLIMATE CONTROL
Main airflow from defroster vents. Some airflow from other vents. Helps remove ice and condensation in cold and humid weather
(blower speed should not be set too low).
Main airflow from dashboard vents. Some airflow from other vents. Provides effective cooling in warm weather.
Main airflow from floor vents. Some airflow from other vents. Provides heating or cooling in footwell areas.
214
CLIMATE CONTROL
Main airflow from defroster and floor vents. Some airflow from Provides a comfortable climate and effective defogging in cold and
other vents. humid weather.
Main airflow from dashboard and floor vents. Some airflow from Provides a comfortable climate in sunny, cool weather.
other vents.
Main airflow from defroster, dashboard and floor vents. Provides balanced comfort in the passenger compartment.
}}
215
CLIMATE CONTROL
|| Related information
• Air distribution (p. 212)
• Opening, closing and directing air vents
(p. 213)
• Adjusting air distribution (p. 212)
216
CLIMATE CONTROL
Button for heated rear window and door mir- Climate view in the center display
rors. Tap the center button on the climate bar to open
Climate view. Climate view is divided into the fol-
Climate bar in the center display lowing tabs:
The most common climate system functions can Max, Electric, Rear - Controls for defrosting
be controlled from the climate bar. • Main climate windows and door mirrors.
• Rear climate* AC - Air conditioning controls.
Toggle between the tabs by swiping the screen
to the left/right or by tapping the desired head- Recirc - Air recirculation controls.
ing.
Air distribution controls.
}}
* Option/accessory. 217
CLIMATE CONTROL
|| Blower control for the front seats (also for Climate controls on the rear side of the
the rear seats on vehicles with 2-zone sys- tunnel console*
tems).
AUTO - Automatic climate control.
218 * Option/accessory.
CLIMATE CONTROL
all selected climate settings will be displayed. The • Activating and deactivating air conditioning Activating and deactivating power
screen locks automatically after a period of inac- (p. 233) front seats*
tivity. • Activating and deactivating climate control The seats can be heated for added comfort for
Related information for the third-row seats* (p. 233) the driver and passengers in cold weather.
• Climate (p. 206)
• Activating and deactivating power front
seats* (p. 219)
• Activating and deactivating the heated rear
seats* (p. 220)
• Activating and deactivating front seat ventila-
tion* (p. 221)
• Activating and deactivating the heated steer-
ing wheel* (p. 222)
• Activating auto climate control (p. 223)
• Activating and deactivating recirculation Steering wheel and seat buttons in the climate row.
(p. 224) 1. Tap the left- or right-side steering wheel and
• Activating and deactivating max defroster seat button in the center display's climate
(p. 225) bar to open the controls for steering wheel
and seat heating.
• Activating and deactivating the heated wind-
shield* (p. 226) If the vehicle is not equipped with ventilated
seats or heated steering wheel, the button
• Activating and deactivating the heated rear
for seat heating is directly accessible in the
window and door mirrors (p. 227)
climate bar.
• Setting the blower speed for the front seats
(p. 228) 2. Tap the seat heating button repeatedly to
select one of the four levels: Off, High,
• Setting the blower speed for the rear seats*
Medium or Low.
(p. 229)
> The level is changed and the set level is
• Synchronize temperature (p. 232) displayed in the button.
}}
* Option/accessory. 219
CLIMATE CONTROL
|| Related information Activating and deactivating the Activating and deactivating the
• Climate system controls (p. 217) heated front seat* heated rear seats*
• Activating and deactivating the heated front The seats can be heated for added comfort for The seats can be heated for added comfort for
seat* (p. 220) the driver and passengers in cold weather. the driver and passengers in cold weather.
Seat heating can be set to automatically activate
when the engine is started. When set to automat- Activating and deactivating the heated
ically activate, heating will be turned on at low rear seats from the front seats*
ambient temperatures.
1. Tap Settings in the Top view in the center
display.
2. Tap Climate.
3. Select Auto Driver Seat Heating Level
and Auto Passenger Seat Heating Level
to activate/deactivate automatic start of
heated driver's and passenger seat.
4. Select Low, Medium or High to select level
after the function has been activated.
Seat heating buttons in the Rear climate group in Cli-
Related information mate view.
• Climate system controls (p. 217)
1. Open Climate view in the center display and
• Activating and deactivating power front select the Rear climate tab.
seats* (p. 219)
2. Tap the seat heating button repeatedly to
select one of the four levels: Off, High,
Medium or Low.
> The level is changed and the set level is
displayed in the button.
220 * Option/accessory.
CLIMATE CONTROL
Activating and deactivating the heated With 4-zone system*: Activating and deactivating front
rear seats from the rear seat seat ventilation*
With 2-zone system: The seats can be ventilated to provide increased
comfort in warm weather.
The ventilation system consists of fans in the
seats and backrest that draw air through the seat
upholstery. The cooler the passenger compart-
ment is, the greater the cooling effect of the ven-
tilation. The system can be activated when the
engine is running.
* Option/accessory. 221
CLIMATE CONTROL
|| 2. Tap the seat ventilation button repeatedly to Activating and deactivating the Related information
select one of the four levels: Off, High, heated steering wheel* • Climate system controls (p. 217)
Medium or Low. The steering wheel can be heated for added • Activating and deactivating automatic steer-
> The level is changed and the set level is comfort in cold weather. ing wheel heating* (p. 223)
displayed in the button.
Related information
• Climate system controls (p. 217)
222 * Option/accessory.
CLIMATE CONTROL
Activating and deactivating Activating auto climate control 2. Tap or press and hold AUTO.
automatic steering wheel heating* If auto climate control is activated, several cli- • Tap - air recirculation, air conditioning and
The steering wheel can be heated for added mate system functions are controlled automati- air distribution are controlled automati-
comfort in cold weather. cally. cally.
Steering wheel heating can be set to automati-
cally activate when the engine is started. When
• Press and hold - air recirculation, air con-
ditioning and air distribution are controlled
set to automatically activate, heating will be
automatically. Temperature and blower
turned on at low ambient temperatures.
speed are changed to standard settings:
1. Tap Settings in the Top view in the center 22 °C (72 °F) and speed 3 (speed 2 in
display. the rear seat3).
2. Tap Climate. > Auto climate mode is activated and the
button lights up.
3. Select Auto Steering Wheel Heating
Level to activate/deactivate automatic start
of heated steering wheel. NOTE
It is possible to change the temperature and
4. Select Low, Medium or High to select level Auto climate button in Climate view. blower speed without deactivating automatic
after the function has been activated.
1. Open Climate view in the center display. climate control. Automatic climate control is
Related information deactivated when the air distribution is
• Activating and deactivating the heated steer- changed manually or when the max defroster
ing wheel* (p. 222) is activated.
Related information
• Climate system controls (p. 217)
* Option/accessory. 223
CLIMATE CONTROL
Related information
• Activating and deactivating recirculation
Air recirculation button in Climate view. (p. 224)
1. Open Climate view in the center display.
2. Tap Recirc.
> Air recirculation is activated/deactivated
and the button lights up/goes out.
CAUTION
If the air in the vehicle is recirculated too long,
there is a risk of fogging on the inside of the
windows.
224
CLIMATE CONTROL
Activating and deactivating max Vehicles with a heated windshield: Activating and deactivating max
defroster – Press the button repeatedly to switch defroster from the center display
Max defroster is used to quickly remove conden- between the three levels:
sation and ice from windows.
• Activated windshield heating
Activating and deactivating max • Activated windshield heating and max
defroster from the center console defroster
A button in the center console offers quick
• Deactivated.
access to the max defroster.
> The heated windshield and max defroster
On vehicles with heated windshields*, the max are activated/deactivated and the button
defroster can only be activated separately from lights up/goes out.
Climate view in the center display.
NOTE
The max defroster starts after a slight delay to Max defroster in Climate view.
avoid a brief increase in blower speed if the 1. Open Climate view in the center display.
heated windshield function has been deacti-
vated by pressing the button twice in quick 2. Tap Max.
succession. > The max defroster is activated/deacti-
vated and the button lights up/goes out.
Max defroster deactivates automatic cli-
mate control and air recirculation, acti-
vates the air conditioning, and changes
blower speed to 5 and temperature to HI.
Button in center console. When max defroster is deactivated, the
Vehicles without a heated windshield: climate system reverts to the previous set-
tings.
– Tap the button.
> The max defroster is activated/deacti- NOTE
vated and the button lights up/goes out.
The volume increases when the blower speed
is changed to 5.
}}
* Option/accessory. 225
CLIMATE CONTROL
|| Related information Activating and deactivating the Activating and deactivating windshield
• Climate system controls (p. 217) heated windshield* heating from the center display
Windshield heating is used to quickly remove
condensation and ice from the windshield.
226 * Option/accessory.
CLIMATE CONTROL
Related information
• Activating and deactivating the heated wind-
shield* (p. 226)
}}
* Option/accessory. 227
CLIMATE CONTROL
|| Activating and deactivating the heated Automatically activating and Setting the blower speed for the
rear window and door mirrors from the deactivating the heated rear window front seats4
center display and door mirrors The blower can be set to several different auto-
The heated rear window and door mirrors are matically controlled speeds for the front seat.
used to quickly remove condensation and ice
from the glass.
It is possible to select whether rear window and
door mirror heating should be automatically acti-
vated or deactivated when the engine is started.
With automatic start activated, heating will be
activated when there is a risk of ice or condensa-
tion on the windows or mirrors. Heating is auto-
matically switched off when the window or door
mirror is sufficiently warm and the condensation
or ice is gone.
Rear window/door mirror heating button in Climate view. 1. Tap Settings in the Top view in the center
1. Open Climate view in the center display. display. Blower control buttons in Climate view.
2. Tap Rear. 2. Tap Climate. 1. Open Climate view in the center display.
> Heated windows and door mirrors are 3. Select Auto Rear Defroster to activate/ 2. Tap the desired blower speed: Off, 1-5 or
activated and the button lights up/goes deactivate automatic rear window and door Max.
out. heating. > The blower speed will be changed and the
buttons for the set speed will light up.
Related information Related information
• Climate system controls (p. 217) • Activating and deactivating the heated rear
CAUTION
• Automatically activating and deactivating the window and door mirrors (p. 227)
heated rear window and door mirrors The air conditioning will not engage if the
(p. 228) blower is turned off completely, which may
cause fogging on the inside of the windows.
4 The same setting applies to the rear seats with the 2-zone climate system.
228
CLIMATE CONTROL
NOTE Setting the blower speed for the 2. Tap the desired blower speed, 1-5.
rear seats* The blower speed for the second and third
The climate system automatically adapts air-
The blower can be set to several different auto- rows of seats* can be switched off by tap-
flow as needed within the set blower speed,
matically controlled speeds for the rear seat. ping 2nd row climate.
which means that airflow speed may vary
slightly within the same blower speed. Setting blower speed for the rear seats The blower speed for the third row of seats is
from the front seats linked to the setting for the second row, but
Related information can be switched off separately* by pressing
• Climate system controls (p. 217) 3rd row climate.
> The blower speed will be changed and the
buttons for the set speed will light up.
}}
* Option/accessory. 229
CLIMATE CONTROL
Related information
• Climate system controls (p. 217)
5 The same setting applies to the rear seats with the 2-zone climate system.
230
CLIMATE CONTROL
Related information
• Climate system controls (p. 217)
}}
* Option/accessory. 231
CLIMATE CONTROL
232
CLIMATE CONTROL
Related information
• Climate system controls (p. 217)
Air conditioning button in Climate view. Air conditioning button in the Rear climate tab in Cli-
mate view.
1. Open Climate view in the center display.
1. Open Climate view in the center display and
2. Tap AC.
select the Rear climate tab.
> The air conditioning is activated/deacti-
vated and the button lights up/goes out. 2. Tap 3rd row climate.
> The air conditioning is activated/deacti-
When the air conditioning is activated, it
vated and the button lights up/goes out.
will be switched on and off automatically
by the climate system as needed.
NOTE
For optimum function of the air conditioning,
close all side windows and the panoramic
roof*.
}}
* Option/accessory. 233
CLIMATE CONTROL
234 * Option/accessory.
KEY, LOCKS AND ALARM
KEY, LOCKS AND ALARM
Exterior confirmation
Locking
• The turn signals will flash once and the door
mirrors will fold in1 to confirm the vehicle is
locked.
Unlocking
• The turn signals will flash twice and the door
mirrors will fold out1 to confirm the vehicle is The locks and alarm indicator on the dashboard will dis-
unlocked. play the status of the locking system.
Lock buttons with indicator lights in front door.
All doors, tailgate and hood must be closed for A long flash indicates that the vehicle is locked.
Illuminated indicator lights in both front door lock
confirmation to be given. If only the driver's door When the vehicle is locked, this will be indicated
buttons indicate that all doors are locked. If any
is closed when the vehicle is locked2, the vehicle by short, pulsing flashes.
door is opened, the lights in both doors will go
will be locked but the turn signals will only flash Other indicators out.
to indicate locking when all doors and the hood The home safe lighting and approach lighting
and tailgate have been closed. functions also indicate when the vehicle is locked
or unlocked.
236 * Option/accessory.
KEY, LOCKS AND ALARM
}}
* Option/accessory. 237
KEY, LOCKS AND ALARM
|| The keyless system for locking/unlocking the Remote key buttons open tailgate (an audible warning signal will
doors, tailgate (Passive Entry*) and fuel filler door sound).
is available as an option. This system has a range Panic alarm - Used to attract attention in
in a semicircle with a radius of approximately emergency situations. Press and hold the
1.5 meter (5 feet) out from the driver's door and button for at least 3 seconds or press twice
approx. 1 meter (3 feet) out from the tailgate. within 3 seconds to activate the turn signals
With keyless start in combination with keyless and horn. To deactivate, wait at least 5 sec-
locking and unlocking, the remote key can be onds and press the button again. If no action
located anywhere in the passenger compartment is taken, the panic alarm will deactivate auto-
or cargo compartment in order to start the matically after 3 minutes.
engine.
Each remote key supplied with the vehicle can be WARNING
linked to a driver profile with unique settings for If anyone is left in the vehicle, make sure that
The remote key has four buttons, one on the left side
the vehicle. When a key with a specific profile is and three on the right. power to the power windows and panoramic
used, the vehicle settings are adjusted according roof* is cut off by always taking the remote
to that profile. Locking - Press once to lock the doors, key with you when you leave the vehicle.
tailgate and fuel filler door and arm the
Buttonless key, Key Tag alarm.
For vehicles equipped with keyless locking and Press and hold to close all windows. NOTE
unlocking*, a smaller, lighter and button-less key Unlocking - Press once to unlock the Be aware of the risk of locking the Key Tag in
(Key Tag3) is also provided. It works the same doors, tailgate and fuel filler door and disarm the vehicle. If the remote key/Key Tag is left
way as the regular remote key as regard keyless the alarm. in the vehicle, it will be deactivated when the
start and keyless locking and unlocking4. It does vehicle is locked and the alarm set using
Press and hold to open all windows at the another valid key.
not have a detachable key blade and its battery
cannot be replaced. same time5.
The deactivated key will be reactivated when
Tailgate - Unlock and disarm the tailgate the vehicle is unlocked.
only. On vehicles equipped with the power
tailgate*, press and hold to automatically
open the tailgate. Press and hold to close an
238 * Option/accessory.
KEY, LOCKS AND ALARM
Interference • Replacing the remote key's battery (p. 242) Locking and unlocking using the
Electromagnetic fields or obstructing objects may • Detachable key blade (p. 248) remote key
interfere with the remote key's functions for key- All doors, tailgate and fuel filler door can be
less start and keyless locking and unlocking*. • Red Key - restricted remote key* (p. 246)
locked and unlocked simultaneously using the
• Electronic immobilizer (p. 250) buttons on the remote key.
NOTE
Avoid storing the remote control key near Locking with remote key
metal objects or electronic devices, e.g. cell
phones, tablets, laptops or chargers – pref-
erably no closer than 10-15 cm (4-6 in.).
NOTE
When the remote control key is placed in the Remote key.
cup holder, make sure that no other vehicle
– Press the button on the remote key to
keys, metal objects or electronic devices (e.g.
lock.
cell phones, tablets, laptops or chargers) are
found in the cup holder. Multiple vehicle keys
close to each other in the cup holder can dis-
rupt their functionality.
Related information
• Locking and unlocking using the remote key
(p. 239)
• Remote key range (p. 241)
}}
* Option/accessory. 239
KEY, LOCKS AND ALARM
|| To activate the locking sequence, the driver's Automatic relocking Settings for remote and inside door
door must be closed6. If any of the other doors or If none of the doors or tailgate are opened within unlock
the tailgate are open, they will be locked and the two minutes after being unlocked, they will auto- Several different sequences are available for
alarm will be armed once they are closed. matically relock. This function reduces the risk of remote unlocking.
inadvertently leaving the vehicle unlocked.
NOTE 1. Tap Settings in the center display's Top
Be aware of the risk of locking the Key Tag in Remote key not working view.
the vehicle. If the remote key/Key Tag is left
2. Tap My Car Locking Remote and
in the vehicle, it will be deactivated when the NOTE
Interior Unlock.
vehicle is locked and the alarm set using Move closer to the vehicle and try to unlock it
another valid key. 3. Select alternative:
again.
The deactivated key will be reactivated when • All Doors
the vehicle is unlocked. If the remote key is not working to lock or unlock - unlocks all doors at the same time.
the vehicle, its battery may be discharged. Use
the detachable key blade to lock/unlock the driv-
• Single Door
Locking when the tailgate is open
er's door instead. - unlocks the driver's door. Press the remote
key unlock button twice to unlock all doors.
NOTE Related information The settings made here also affect central lock-
If the vehicle is locked and the tailgate is still • Settings for remote and inside door unlock
ing using the inside door handle.
open, make sure that the remote key is not (p. 240)
left in the cargo compartment when the tail- • Unlocking the tailgate using the remote key Related information
gate is closed and the entire vehicle is (p. 241) • Locking and unlocking using the remote key
locked7. (p. 239)
• Remote key (p. 237)
• Replacing the remote key's battery (p. 242) • Locking and unlocking from inside the vehi-
Unlocking with remote key cle (p. 255)
– Press the button on the remote key to
• Locking and unlocking with detachable key
blade (p. 249)
unlock.
6 If the vehicle is equipped with keyless locking/unlocking, all side doors must be closed.
7 If the vehicle is equipped with keyless locking/unlocking and the key is detected inside the vehicle, the tailgate will not lock when it is closed.*
240 * Option/accessory.
KEY, LOCKS AND ALARM
Unlocking the tailgate using the 1. Press the button on the remote key. Remote key range
remote key > The lock and alarm indicator on the dash- In order to function correctly, the remote key
The remote key can be used to unlock the tail- board will go out to indicate that the vehi- must be within a certain distance from the vehi-
gate while keeping the rest of the vehicle locked. cle is no longer fully armed. cle.
The tailgate will be unlocked but remain Manual use
closed. However, the side doors will The remote key's functions for e.g. locking and
remain locked and armed. unlocking, which are activated by pressing or
To open the tailgate, lightly grasp the rub- , have a range of approx. 20 meter (65 feet)
berized pressure plate on the underside from the vehicle.
of the tailgate handle and open the tail-
If the vehicle's locks do not react, move closer
gate.
and try again.
If the tailgate is not opened within
2 minutes, it will be relocked and the Keyless use8
alarm armed.
With the optional power tailgate* -
Use the button on the remote key to disarm and
unlock the tailgate. 2. Hold and press (about 1.5 seconds) the
button on the remote key
> The tailgate will unlock and open. How-
ever, the side doors will remain locked and
armed.
Related information
• Locking and unlocking using the remote key
(p. 239)
• Opening and closing the power tailgate* The shaded areas around the vehicle illustrate the range
of the system's antennas.
(p. 259)
* Option/accessory. 241
KEY, LOCKS AND ALARM
|| For keyless use, a remote key or the Key Tag • Keyless and touch-sensitive surfaces* Replacing the remote key's battery
must be within the shaded areas shown in the (p. 251) The battery in the remote key must be replaced
illustration, i.e. a semicircle with a radius of when it is discharged.
approx. 1.5 meter (5 feet) along the sides of the
vehicle or approx. 1 meter (3 feet) from the tail- NOTE
gate. All batteries have a limited service life and
must eventually be replaced (does not apply
NOTE for Key Tag). The battery's service life varies
depending on how often the vehicle/key is
The functions of the remote control key can used.
be disrupted by ambient radio waves, build-
ings, topographical conditions, etc. The vehi-
cle can always be locked/unlocked using the The remote key battery should be replaced if:
key blade. the information symbol illuminates and
the message Vehicle key bat. low
If the remote key is removed from the See Owner's manual is displayed in
vehicle the instrument panel
If the remote key is removed from the and/or
vehicle while the engine is running, the
warning message Vehicle key not • the locks do not react after several attempts
to lock or unlock the vehicle using the
found Removed from vehicle will be
remote key within approx. 20 meter (65 feet)
displayed in the instrument panel and an audible
from the vehicle.
signal will sound when the last door is closed.
The message will disappear when the key is NOTE
returned to the vehicle and the O button on the
right-side steering wheel keypad is pressed or Move closer to the vehicle and try to unlock it
when the last door is closed again. again.
Related information
• Remote key (p. 237)
• Antenna locations for the start and lock sys-
tem (p. 255)
242 * Option/accessory.
KEY, LOCKS AND ALARM
The battery in the smaller key without buttons9 Opening the key and replacing the
(the Key Tag) cannot be replaced. A new key can battery
be ordered from an authorized Volvo workshop.
CAUTION
An end-of-life Key Tag must be turned in to
an authorized Volvo workshop. The key must
be deleted from the vehicle because it can
still be used to start the vehicle via backup
start. Turn the key over, move the button to the
side and slide the rear cover slightly upward.
Hold the remote key with the front side
The cover will loosen and can be
(with the Volvo logo) facing up and move the
removed from the key.
button on the key ring section to the right.
Slide the front cover slightly upward.
The cover will loosen and can be
removed from the key.
9 This key is provided with vehicles equipped with keyless locking/unlocking (Passive Entry*). }}
* Option/accessory. 243
KEY, LOCKS AND ALARM
||
Use a screwdriver or similar object to turn The battery's positive side (+) faces upward. Insert a new battery with the positive side (+)
the battery cover counterclockwise so the Carefully pry out the battery as shown in the facing upward. Do not touch the contact sur-
markers point to OPEN. illustration. faces of the remote key battery.
Remove the cover carefully by pressing e.g. a Place the edge of the battery downward
fingernail into the indentation. CAUTION into the holder. Slide the battery forward until
Pry the cover up. Avoid touching new batteries and their con- it locks into place under the two plastic
tact surfaces with your fingers as this will catches.
impair their function.
Press the battery downward until it locks
into place under the upper black plastic
catch.
NOTE
Use batteries with the designation CR2032,
3 V.
244
KEY, LOCKS AND ALARM
NOTE CAUTION
Volvo recommends that batteries used in the Be sure to dispose of end-of-life batteries in
remote control key satisfy UN Manual of Test a way that protects the environment.
and Criteria, Part III, sub-section 38.3. The
factory installed batteries and batteries
Related information
replaced by an authorized Volvo workshop
satisfy the above criterion.
• Remote key (p. 237)
245
KEY, LOCKS AND ALARM
Ordering additional remote keys NOTE Red Key - restricted remote key*
Two remote keys are provided with the vehicle. A Red Key makes it possible for the vehicle
Volvo recommends that you order a new or
One Key Tag is also included if the vehicle is owner to set limitations for certain vehicle prop-
duplicate remote control key from an author-
equipped with keyless locking/unlocking*. Addi- erties. The limitations are intended to promote
ized Volvo workshop.
tional keys can be ordered. safe use of the vehicle, e.g. when it is loaned
A total of 12 keys can be programmed and used You can also obtain additional or duplicate out.
for the same vehicle. An additional driver profile remote control keys from certain independent
will be added for each new remote key. This also repair facilities and locksmiths that are quali-
applies to the key tag. fied to make remote control keys. Each key
must be programmed to work with your vehi-
Loss of a remote key cle.
If you lose your remote key, you can order a
replacement from a workshop - an authorized A list of independent repair facilities and/or
Volvo workshop is recommended. Bring the other locksmiths known to Volvo that can cut and
remaining remote keys to the workshop. As an code replacement keys can be found:
anti-theft measure, the code of the lost remote • on Volvo's website www.volvocars.com/us
key must be erased from the system.
• by calling Volvo Customer Care
The current number of keys registered for the 1-800-458-1552.
vehicle can be checked via driver profiles in the
center display's Top view. Select Settings Related information For a Red Key, it is possible to define the vehi-
System Driver Profiles. • Remote key (p. 237) cle's maximum speed, set speed reminders and
limit the audio system's volume. Several of the
driver support systems will also always be active.
Otherwise, the Red Key functions in the same
way as a standard remote key.
One or more Red Keys can be ordered from a
Volvo retailer. A total of twelve keys can be pro-
grammed and used for the same vehicle. Up to
ten may be restricted keys, but at least two must
be standard remote keys.
These restrictions are intended to help reduce
the risk of accidents and help the driver feel more
246 * Option/accessory.
KEY, LOCKS AND ALARM
secure when handing over the vehicle to e.g. a Red Key* settings Speed reminder (On/Off):
young driver, parking attendant or workshop. The The holder of a regular remote key can adjust • Setting interval: 0-250 km/h (0-160 mph)
settings for a Red Key cannot be changed by its
user; a regular remote key is needed to change
settings for a Red Key. Certain driver support • Default setting: 50, 70 and 90 km/h (30, 45
functions are always active. and 55 mph)
settings. 1. Tap Settings in the center display's Top
view.
• Increments: 1 km/h (1 mph)
Related information • Maximum number of simultaneous remind-
• Red Key* settings (p. 247) 2. Tap System Driver Profiles Red Key. ers: 6
• Remote key (p. 237) > The following settings can be made:
Driver support functions
• Set Time Gap For Adaptive Cruise The following driver support functions will always
Control be active for a Red Key user:
• Reduced Maximum Volume • Blind Spot Information (BLIS)*
• Max Speed Limit • Lane Keeping Aid (LKA)*
• Speed Limit Warning • Distance Alert*
Adaptive Cruise Control*: • City Safety
• Default setting: Longest interval • Driver Alert Control (DAC)*
Reduced maximum volume (On/Off): • Road Sign Information*
• Default setting: On
Speed Limiter (On/Off):
Related information
• Setting interval: 50-250 km/h (30-160 mph) • Red Key - restricted remote key* (p. 246)
* Option/accessory. 247
KEY, LOCKS AND ALARM
248 * Option/accessory.
KEY, LOCKS AND ALARM
Locking and unlocking with Lock the door in the same way, but turn the key Locking
detachable key blade 45 degrees counterclockwise in step (3). The vehicle can also be locked using the remote
The detachable key blade can be used to unlock Turning off the alarm key's detachable key blade, e.g. if either the vehi-
the vehicle from the outside, e.g. if the battery in cle's or remote key's batteries are discharged.
the remote key is discharged. The left-hand front door can be locked by insert-
NOTE
ing the detachable key into the door's lock cylin-
Unlocking When the door is unlocked using the detach- der.
able key blade and then opened, the alarm
will be triggered. This is the only door with a lock cylinder. The
other doors have lock mechanisms in the side of
the door that must be pushed in using the key
blade. The door will then be locked mechanically
and cannot be opened from the outside.
The doors can still be opened from inside.
Turn the key clockwise 45 degrees so that Turn off the alarm by:
the key blade is pointing straight rearward. 1. Place the remote control key on the key sym-
Turn the key blade back 45 degrees to its bol in the backup reader in the bottom of the
original position. Remove the key from the cup holder in the tunnel console.
lock cylinder and release the handle so that it 2. Turn the start knob clockwise and release it.
returns to its original position against the Manual door lock. This is not the child lock.
> The start knob will automatically return to
vehicle.
its original position - the alarm signal will – Remove the detachable key blade from the
5. Pull the door handle. stop and the alarm will be turned off. remote key. Insert the key blade into the
> The door will open. opening for the lock mechanism and push
the key in as far as possible, about 12 mm.
}}
249
KEY, LOCKS AND ALARM
|| The door can be opened from both the out- Electronic immobilizer Start and lock system type
side and the inside. The electronic immobilizer is a start inhibitor that designations
The door cannot be opened from the outside. helps prevent the vehicle from being started by The following information contains type designa-
To return to position A, open the door using an unauthorized person. tions for the start and lock system.
the inside door handle. The vehicle can only be started with the right
remote key. Alarm system
The doors can also be unlocked by pressing the
USA FCC ID: MAYDA 5823(3)
unlock button on the remote key or the central The following instrument panel error messages
lock button in the driver's door. are related to the electronic immobilizer: This device complies with part 15 of the FCC
rules. Operation is subject to the following condi-
NOTE Symbol Message Meaning tions: (1) This device may not cause harmful
interference, and (2) this device must accept any
• The door's lock controls only lock that Vehicle key Remote key not interference received, including interference that
specific door, not all doors simultane- not found recognized during may cause undesired operation.
ously. start. Place the
See Canada IC: 4405A-DA 5823(3)
• A manually locked rear door with an acti-
Owner's
remote key on the
vated manual or electric child safety lock key symbol in the This device is subject to the following conditions:
manual (1) this device may not cause interference, and
cannot be opened from either the outside cup holder and try
or inside of the vehicle. A rear door to start the vehicle (2) this device must accept any interference,
locked in this way can only be unlocked again. including interference that may cause undesired
using the remote key or the central operation of the device.
unlocking button. Related information
Remote keys (Passive entry/Passive
• Remote key (p. 237)
start*)
Related information • Ordering additional remote keys (p. 246) USA
• Detachable key blade (p. 248)
Volvo Standard Key FCC ID: YGOHUF8423
• Arming and disarming the alarm (p. 267)
Volvo Tag ID FCC ID: YGOHUF8432
• Replacing the remote key's battery (p. 242)
This device complies with part 15 of the FCC
• Remote key (p. 237)
rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interfer-
ence, and
250 * Option/accessory.
KEY, LOCKS AND ALARM
(2) this device must accept any interference Any changes or modification not expressly Keyless and touch-sensitive
received, including interference that may cause approved by the party responsible for compliance surfaces*
undesired operation. could void the user's authority to operate this If the vehicle is equipped with keyless locking
equipment. and unlocking, it is only necessary to have the
Any changes or modification not expressly
approved by the party responsible for compliance Canada-IC:3659A-VO3134 remote key within range, e.g. in a pocket or bag,
could void the user's authority to operate this which makes it easier to open the vehicle if your
This device complies with Industry Canada
equipment. hands are full.
license-exempt RSS standards. Operation is sub-
Canada ject to the following two conditions:
Volvo Standard Key IC: 4008C-HUF8423 (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any inter-
Volvo Tag ID IC: 4008C-HUF8432
ference received, including interference that may
This device complies with Industry Canada cause undesired operation.
license-exempt RSS standards. Operation is sub-
ject to the following two conditions: Related information
(1) This device may not cause harmful interfer-
• Remote key (p. 237)
ence, and (2) this device must accept any inter-
ference received, including interference that may
cause undesired operation.
* Option/accessory. 251
KEY, LOCKS AND ALARM
NOTE
Please be aware that the system could be Pressure-sensitive indentation for locking
activated in a car wash if the remote key is
Pressure-sensitive indentation for locking Pressure-sensitive surface for unlocking
within range.
Pressure-sensitive surface for unlocking
Related information
NOTE • Keyless locking and unlocking* (p. 252)
252 * Option/accessory.
KEY, LOCKS AND ALARM
* Option/accessory. 253
KEY, LOCKS AND ALARM
Keyless unlock settings* Keyless tailgate unlock* 2. Lift the outer handle to fully open the tail-
Several different sequences are available for The tailgate can be opened using the remote gate.
keyless unlocking. key. The key only needs to be within range, e.g.
in a pocket or bag. CAUTION
1. Tap Settings in the center display's Top The tailgate is held closed by an electronic lock-
view. • Only light pressure on the rubberized pres-
ing mechanism. sure plate is necessary to release the tail-
2. Tap My Car Locking Keyless Unlock gate's locking mechanism.
3. Select alternative: • Use the handle to lift the tailgate and do
not apply force to the rubberized pressure
• All Doors plate. Too much force can damage the
- unlocks all doors at the same time. pressure plate's electrical connections.
• Single Door
- unlocks the selected door. Hands-free unlocking of the tailgate is also pos-
sible using a foot movement under the rear
Related information bumper; see the separate section.
• Keyless locking and unlocking* (p. 252)
• Keyless and touch-sensitive surfaces* WARNING
(p. 251)
To open the tailgate: Do not drive with the tailgate open. Toxic
exhaust fumes can be sucked into the vehicle
1. Lightly press the rubberized pressure plate through the cargo compartment.
on the underside of the tailgate handle.
> The lock will disengage. Related information
• Keyless locking and unlocking* (p. 252)
NOTE
• Keyless and touch-sensitive surfaces*
One of the vehicle's remote keys must be (p. 251)
within range behind the vehicle for unlocking
to be possible.
• Remote key range (p. 241)
• Foot movement tailgate operation* (p. 263)
254 * Option/accessory.
KEY, LOCKS AND ALARM
Antenna locations for the start and WARNING Locking and unlocking from inside
lock system the vehicle
Individuals with an implanted pacemaker
The vehicle is equipped with a keyless start and should not allow the pacemaker to come The doors and tailgate can be locked and
lock system13 that uses a number of integrated closer than 22 cm (9 in.) to the Keyless sys- unlocked from inside the vehicle using the cen-
antennas positioned throughout the vehicle. tem antennas. The aim of this is to prevent tral lock buttons in the front doors. The lock but-
disturbances between the pacemaker and the tons in the rear doors* can be used to lock/
Keyless system. unlock that particular door.
13 The keyless lock system only applies to vehicles equipped with keyless locking and unlocking (Passive Entry*).
14 Only in vehicles equipped with keyless locking and unlocking (Passive Entry*).
15 The total airing function can be used to e.g. quickly air out the vehicle in hot weather. }}
* Option/accessory. 255
KEY, LOCKS AND ALARM
|| Alternative unlocking method Locking using the front door buttons Related information
– Press the button (both front doors must • Settings for remote and inside door unlock
be closed). (p. 240)
> All doors and the tailgate will lock. • Unlocking the tailgate from inside the vehicle
(p. 257)
Press and hold the button to close all side
windows at the same time. • Activating and deactivating child safety locks
(p. 257)
Locking using the rear door button*
256 * Option/accessory.
KEY, LOCKS AND ALARM
Unlocking the tailgate from inside Related information Activating and deactivating child
the vehicle • Locking and unlocking from inside the vehi- safety locks
The tailgate can be locked from the inside using cle (p. 255) Child safety locks help prevent children from
a button on the dashboard. • Opening and closing the power tailgate* opening the rear doors from inside the vehicle.
1. (p. 259) There is an electric safety lock* and a manual
safety lock.
}}
* Option/accessory. 257
KEY, LOCKS AND ALARM
|| 2. Press the button on the driver's door control Symbol Message Meaning NOTE
panel.
> The message Rear child lock Activated Rear child The child safety • The door's knob control only locks that
lock Acti- locks are acti- specific door, not both rear doors simulta-
will be shown in the instrument panel and
vated vated. neously.
the indicator light will illuminate to show
that the child safety locks are activated. • There are no manual child safety locks on
Rear child The child safety models equipped with electronic child
When the electric child safety locks are activated: lock Deacti- locks are deacti- safety locks.
• the rear windows can only be opened using vated vated.
the driver's door control panel Related information
• the rear doors cannot be opened from the Activating and deactivating manual • Locking and unlocking from inside the vehi-
inside. child safety locks cle (p. 255)
To deactivate the child safety locks: • Detachable key blade (p. 248)
– Press the button on the driver's door control
panel.
> The message Rear child lock
Deactivated will be shown in the instru-
ment panel and the indicator light will go
out to show that the child safety locks are
deactivated.
When the engine is turned off, the current setting
will be saved. If the locks were activated when
the engine was turned off, they will remain acti-
vated the next time the engine is started. Manual child safety lock (this is not the manual door
lock).
– Use the detachable key blade in the remote
key to turn the control.
The door cannot be opened from the inside.
258
KEY, LOCKS AND ALARM
Automatic locking when driving Opening and closing the power – Press and hold the button on the dash-
The doors and tailgate will automatically lock tailgate* board until the tailgate begins to open.
when the vehicle begins to move. The tailgate can be opened and closed automat-
ically with the optional power tailgate.
Related information
• Locking and unlocking from inside the vehi- Opening the power tailgate
cle (p. 255) To open the tailgate, do one of the following:
– Press and hold the button on the
remote key until the tailgate begins to open.
}}
* Option/accessory. 259
KEY, LOCKS AND ALARM
|| – Move your foot in a kicking motion* under the – Press the button on the lower edge of – Press and hold the button on the dash-
rear bumper. the tailgate to close. board.
> The tailgate closes automatically and an
audible signal will sound - the tailgate will
remain unlocked.
– Move your foot in a kicking motion* under
the rear bumper.
> The tailgate closes automatically and an
audible signal will sound - the tailgate will
remain unlocked.
17 Vehicles equipped with keyless locking and unlocking (Passive Entry*) have a button for closing and a button for closing and locking.
260 * Option/accessory.
KEY, LOCKS AND ALARM
• One of the vehicle's remote keys must be Tailgate movement is interrupted and stops. The
within range for locking and unlocking to trunk lid can then be opened or closed manually.
be possible.
Pinch protection
• When the keyless locking or closing* func- If anything obstructs the tailgate with enough
tions are used, three audible signals will force to prevent it from opening or closing, pinch
sound if the key is not detected close protection will be activated.
enough to the tailgate.
• When opening - the tailgate will stop moving
and an audible signal will sound.
• When closing - the tailgate will stop, a long
Preloaded springs for the power tailgate.
CAUTION audible signal will sound and the tailgate will
When operating the tailgate manually, open return to the programmed maximum opening
and close it slowly. If you encounter resis- position. WARNING
tance, do not use force. This could lead to Do not attempt to open or access the preloa-
damage and loss of function. ded springs in the power tailgate struts. They
are preloaded with high pressure and can
cause injury if opened.
17 Vehicles equipped with keyless locking and unlocking (Passive Entry*) have a button for closing and a button for closing and locking. }}
* Option/accessory. 261
KEY, LOCKS AND ALARM
262 * Option/accessory.
KEY, LOCKS AND ALARM
Foot movement tailgate operation* Foot movement operation Do not keep your foot under the vehicle in a kick-
To make it easier to operate the tailgate when ing motion. This may prevent activation.
your hands are full, it can be opened and closed Interrupting opening or closing with a foot
by moving your foot in a forward kicking motion movement
under the rear bumper. – Make one slow forward kicking motion while
the tailgate is opening or closing to stop its
movement.
The remote key does not need to be within range
of the vehicle to interrupt opening or closing.
NOTE
There is a risk of reduced or lost function if
Kicking motion within the sensor's activation area. there are large amounts of snow, ice, dirt, etc.
– Make one slow forward kicking motion with on the rear bumper. Make sure to keep the
your foot under the left section of the rear bumper clean.
bumper. Take a step back. Do not touch the
The sensor is located to the left of center under the rear bumper.
bumper18. NOTE
> A brief audible signal will be heard when
One of the vehicle's remote keys must be within opening or closing is activated - the tail- Please note that the system could be inadver-
range behind the vehicle (approx. 1 meter (3 gate will open/close. tently activated in a car wash or similar if the
feet)) for opening and closing to be possible. This remote key is within range.
applies even if the vehicle is unlocked in order to If the tailgate is open, it will always close19
prevent the trunk lid from inadvertently opening when the foot motion sensor is activated.
Vehicle with skid plate accessory*
e.g. at a car wash. If several opening attempts have been made If the vehicle is equipped with skid plate, the sen-
without the remote key in range behind the vehi- sor is located towards the left corner of the
cle, foot movement operation will not be available bumper.
for a short period of time.
18 If the vehicle is equipped with skid plate*, the sensor is located towards the left corner of the bumper.
19 Applies to vehicles with power tailgate*. }}
* Option/accessory. 263
KEY, LOCKS AND ALARM
264 * Option/accessory.
KEY, LOCKS AND ALARM
Activating and deactivating private 2. Enter your security code. Deactivating private locking
locking > The security code is saved. The private 1. Tap the button for private locking in Function
Private locking is activated using the function locking function is now ready for activa- view.
button in the center display and a PIN code. tion.
NOTE If the system has been reset, the above proce-
For the valet lock function to be activated the dure will need to be repeated.
car must be in at least ignition mode I. Activating private locking
1. Tap the button for private locking in Function
Entering security code before initial use view. > A pop-up window will appear.
The first time the function is used, a security
2. Enter the code used for locking and tap
code must be selected. This code can then be
used to deactivate private locking if the selected
Confirm.
PIN code has been lost or forgotten. The security > The glove compartment and tailgate will
code functions as a PUK (security) code for all unlock. The green indicator light next to
PIN codes used for private locking. the button in Function view will go out to
confirm unlocked status.
Save the security code in a safe place. > A pop-up window will appear.
To create a security code: 2. Enter the code you would like to use to NOTE
unlock the glove compartment and the tail-
1. Tap the button for private locking in Function If you have forgotten or lost your PIN code or
view. gate and tap Confirm.
if the PIN code has been entered incorrectly
> The glove compartment and tailgate will more than three times, the security code can
lock. A green indicator light will illuminate be used to deactivate private locking.
next to the button in Function view to con-
firm locked status.
NOTE
If private locking is activated and the vehicle
> A pop-up window will appear. is unlocked using Volvo On Call* or the Volvo
On Call* app, private locking will be deacti-
vated automatically.
}}
* Option/accessory. 265
KEY, LOCKS AND ALARM
Alarm signals
The following occurs if the alarm is triggered:
A red indicator light on the dashboard shows the
• A siren will sound for 30 seconds or until the
alarm is turned off. status of the alarm:
• All turn signals will flash for 5 minutes or • Indicator off - the alarm is disarmed.
until the alarm is turned off. • Indicator flashes once every two seconds -
If the reason the alarm was triggered is not recti- the alarm is armed.
fied, the alarm cycle will repeat up to 10 times20. • The indicator flashes quickly after the alarm
has been disabled for up to 30 seconds or
until the ignition is put in I mode by turning
the start knob clockwise and then releasing -
the alarm has been triggered.
266
KEY, LOCKS AND ALARM
In the event of alarm system failure Arming and disarming the alarm Disarming the alarm
If a problem is detected in the alarm The alarm is armed when the vehicle is locked. Unlock and disarm the vehicle alarm by:
system, a symbol and the message
Alarm system failure Service Arming the alarm • pressing the unlock button on the remote
required will appear in the instrument Lock and arm the vehicle by: key
panel. Contact a workshop - an authorized Volvo
• pressing the lock button on the remote key • grip a door handle or press the tailgate's rub-
workshop is recommended. berized pressure plate21.
* Option/accessory. 267
KEY, LOCKS AND ALARM
3. Turn the start knob clockwise and release. To change this setting:
> The alarm will be disarmed. 1. Tap Settings in the center display's Top
view.
Turning off a triggered alarm
– Press the unlock button on the remote key 2. Tap My Car Locking.
or put the ignition into mode I by turning the 3. Select Passive Arming Deactivation to
start knob clockwise and then releasing it. temporarily deactivate the function.
Related information
• Alarm (p. 266)
268 * Option/accessory.
DRIVER SUPPORT
DRIVER SUPPORT
Driver support systems • Cross Traffic Alert* (p. 351) Speed-dependent steering wheel
The vehicle is equipped with a number of driver • Road Sign Information* (p. 355) resistance
support systems that can provide the driver with Speed-dependent power steering increases the
active or passive assistance in various situations.
• Driver Alert Control (p. 360)
steering wheel resistance in pace with the vehi-
• Lane Keeping Aid (p. 362) cle's speed to give the driver an enhanced feel-
The system can, for example, help the driver
• Steering assistance at risk of collision ing of control and stability.
maintain a set speed or a set time interval to the (p. 370)
vehicle ahead, help prevent a collision by warning Steering may feel stiffer on highways. When
the driver and applying the brakes, or assist the • Park Assist* (p. 379) parking and at low speeds, it will be easier to
driver while parking. • Park Assist Camera* (p. 384) move the steering wheel.
Some of the systems are standard and others are • Park Assist Pilot* (p. 393)
options. This also varies from market to market. NOTE
In some situations, the power steering may
Related information
become too hot and require temporary cool-
• Speed-dependent steering wheel resistance
ing – during such time the power steering will
(p. 270)
work at reduced output and the steering
• Electronic Stability Control (p. 272) wheel may feel more difficult to move.
• Stability system Roll Stability Control In parallel with the temporarily reduced steer-
(p. 271) ing assistance, the driver display shows a
• Rear Collision Warning (p. 345) message as well as a STEERING WHEEL
• Speed limiter (p. 276) symbol.
270 * Option/accessory.
DRIVER SUPPORT
WARNING • Lane Keeping Aid (p. 362) Stability system Roll Stability
• Steering assistance at risk of collision Control
While the power steering is working at
reduced power, the driver support functions (p. 370) The Roll Stability Control (RSC1) system helps
with steering assistance are not available. • Park Assist Pilot* (p. 393) minimize the risk of a rollover in the event of e.g.
a sudden evasive maneuver or if the vehicle
In such a situation, the driver display shows
the Power steering failure or Power begins to skid.
Steering Assist Temporarily Reduced
The RSC system monitors the lateral angle at
message, combined with a STEERING
WHEEL symbol. which the vehicle is leaning and registers any
changes. Using this information, the system cal-
culates the likelihood of a rollover. If there is an
Changing the level of steering wheel imminent risk of a rollover, Electronic Stability
Control is activated, engine torque is reduced and
resistance*
brakes are applied to one or more of the wheels
To change the level of steering wheel resistance,
until the vehicle has regained stability.
see the description of the INDIVIDUAL option
under "Available drive modes" in the "Drive
modes" section. WARNING
On models not equipped with drive mode con- The vehicle’s stability systems, including RSC
do not replace the driver’s responsibility for
trols and the INDIVIDUAL option, steering wheel
operating the vehicle in a safe manner. Speed
resistance can instead be set in the center dis- and driving style should always be adapted to
play's Top view under: the current road, traffic and weather condi-
tions. Posted speed limits should always be
Settings My Car Drive Modes respected.
Steering force
Steering wheel resistance settings cannot be
accessed when turning at speeds above
10 km/h (6 mph).
Related information
• Drive modes* (p. 423)
• Pilot Assist (p. 309)
* Option/accessory. 271
DRIVER SUPPORT
272 * Option/accessory.
DRIVER SUPPORT
• Electronic Stability Control Sport mode limi- Electronic Stability Control Sport Activating/deactivating Sport mode
tations (p. 274) mode in Electronic Stability Control
• Electronic Stability Control symbols and mes- The ESC7 system is always activated and can- The ESC9 system is always activated and can-
sages (p. 275) not be switched off. However, the driver can not be switched off. However, the driver can
select ESC Sport Mode, which offers more select Sport mode, which offers more active
active driving characteristics. driving characteristics.
Sport mode can be activated/
With the ESC Sport Mode sub-function deactivated in the center dis-
selected, intervention from ESC is reduced and play's Function view.
more lateral movement is permitted, giving the
driver more control of the vehicle than usual.
When ESC Sport Mode is selected, ESC may
seem to be disabled even though it is often
– Tap the ESC Sport Mode button in Func-
assisting the driver.
tion view.
> Sport mode is activated when the indica-
NOTE tor light is green, and deactivated when
When the ESC Sport Mode function is the indicator light is gray.
selected, the trailer stabilizer (TSA8) is When ESC Sport Mode is activated,
switched off. this symbol will illuminate with a steady
glow in the instrument panel. It will
ESC Sport Mode also helps provide maximum remain on until the driver deactivates
traction if the vehicle gets stuck or is driving on a the function or until the engine is turned off. The
loose surface such as deep snow or loose sand. ESC system will return to normal mode the next
time the engine is started.
Related information
Related information
• Electronic Stability Control (p. 272)
• Electronic Stability Control (p. 272)
273
DRIVER SUPPORT
Related information
• Electronic Stability Control (p. 272)
274
DRIVER SUPPORT
Electronic Stability Control symbols Some examples of symbols and messages are
and messages shown in the table below.
A number of symbols and messages related to
Electronic Stability Control (ESC) may be dis-
played in the instrument panel.
ESC The ESC system's functionality has been temporarily reduced due to high brake system temperatures. The
function will be automatically reactivated when the brakes have cooled.
Temporarily off
See the message in the instrument panel.
ESC The ESC system is not functioning properly.
Service required • Stop the vehicle in a safe place, turn off the engine and then restart it.
• Consult a workshop if the message persists ‒ an authorized Volvo workshop is recommended.
A text message can be erased by briefly pressing If the message persists: Contact a workshop ‒ an Related information
the button in the center of the right-side authorized Volvo workshop is recommended. • Electronic Stability Control (p. 272)
steering wheel keypad.
275
DRIVER SUPPORT
11 Speed Limiter
12 Note: This illustration is general and details may vary depending on model.
276
DRIVER SUPPORT
Activating and starting Speed – With the Speed Limiter in standby mode and Managing Speed Limiter speed
Limiter The Speed Limiter (SL14) can be set to various
the symbol displayed, press the
The Speed Limiter (SL13) function must be speeds.
button (2) on the steering wheel key-
selected and activated in order to regulate
pad. Setting/changing set speed
speed.
> The Speed Limiter will be started and the
Putting Speed Limiter in standby mode vehicle's current speed will be set as the
maximum speed.
Related information
• Speed limiter (p. 276)
Starting the Speed Limiter • Press and hold: Release the button when
the set speed indicator (4) has moved to
The Speed Limiter can only be activated while
the desired speed.
the engine is running. The lowest maximum
speed that can be set is 30 km/h (20 mph). • The most recently set speed will be stored.
13 Speed Limiter }}
277
DRIVER SUPPORT
|| Related information Deactivating and putting Speed Temporarily deactivating using the
• Speed limiter (p. 276) Limiter in standby mode accelerator pedal
The Speed Limiter (SL15) can be temporarily The set maximum speed can be temporarily
deactivated and put in standby mode. deactivated and exceeded using the accelerator
pedal without first putting the Speed Limiter in
standby mode, e.g. when quick acceleration is
required.
To do so:
1. Depress the accelerator as far as possible
and then release it when the desired speed
has been reached.
> The Speed Limiter will remain activated
and the symbol in the instrument panel
will be WHITE.
2. Release the accelerator pedal fully when the
Note: This illustration is general and details may vary temporary acceleration is completed.
depending on model.
> The vehicle will automatically slow down
To deactivate the Speed Limiter and put it in to a speed below the most recently set
standby mode: maximum speed.
– Press the button on the steering wheel Related information
(2). • Speed limiter (p. 276)
> The speed limit markings and symbols in
the instrument panel will change from
WHITE to GRAY. This indicates that the
Speed Limiter is temporarily deactivated
and the driver can exceed the set maxi-
mum speed.
14 Speed Limiter
15 Speed Limiter
278
DRIVER SUPPORT
Reactivating Speed Limiter from – Press the button on the steering wheel Turning off Cruise Control
standby mode (2). The Speed Limiter (SL17) can be turned off.
Speed Limiter (SL16) can be reactivated after > The speed limit markings and symbols in
having been temporarily deactivated and put in the instrument panel will change from
standby mode. GRAY to WHITE and the vehicle's current
speed will be set as the maximum speed.
Related information
• Speed limiter (p. 276)
Note: This illustration is general and details may vary 1. Press the button on the steering wheel
depending on model. (2).
To reactivate the Speed Limiter from standby > The Speed Limiter will go into standby
mode: mode.
– Press the button on the steering wheel 2. Press the ◀ (1) or ▶ (3) buttons on the
(1). steering wheel to select another function.
> The speed limit markings in the instru- > The Speed Limiter symbol and marking
ment panel will change from GRAY to (4) in the instrument panel will go out and
WHITE. The vehicle's speed will once the set maximum speed will be erased.
again be limited to the most recently set
3. Press the (2) button on the steering
speed.
wheel keypad again.
or > Another function will be activated.
16 Speed Limiter }}
279
DRIVER SUPPORT
Related information
• Speed limiter (p. 276)
17 Speed Limiter
18 Automatic Speed Limiter
19 Speed Limiter
20 Road Sign Information – RSI
280
DRIVER SUPPORT
281
DRIVER SUPPORT
282
DRIVER SUPPORT
Changing Automatic Speed Limiter – Tap the (1) button on the steering Automatic Speed Limiter limitations
tolerance wheel keypad until 70 km/h (43 mph) has ASL utilizes the speed limit information provided
The Automatic Speed Limiter (ASL23) can be set been changed to 75 km/h (47 mph) in the by the RSI25 system, not from the speed limit
to different tolerance levels. center of the speedometer (4). signs that the vehicle passes.
> The vehicle will then use the selected tol- If RSI25 is unable to interpret and provide ASL
It is also possible to allow the vehicle to drive erance of 5 km/h (4 mph) as long as the with speed information, ASL will go into standby
above or below the posted speed limit. For exam- posted speed limit the vehicle passes is mode and switch over to SL. The driver will then
ple, if the vehicle is following a current posted 70 km/h (43 mph). have to actively brake to bring the vehicle down
speed limit of 70 km/h (43 mph), the driver can to the appropriate speed.
instead allow the vehicle to maintain a speed of This tolerance level will be followed until
75 km/h (47 mph). the vehicle passes a sign with a lower or ASL will be reactivated when RSI25 is once again
higher speed. The vehicle will then adjust able to interpret and provide speed information to
to the new speed limit and the set toler- ASL.
ance will be deleted from the system's
See "Road Sign Information limitations" for more
memory.
information.
If Road Sign Information* is activated, the
posted speed limit will then be indicated Related information
by a RED marking on the speedometer's • Speed limiter (p. 276)
speed scale.
The set tolerance can be adjusted in the same
way as for the Speed Limiter's speed.
NOTE
Function buttons and symbols24.
The highest possible selectable tolerance is
+/- 10 km/h (5 mph).
Related information
• Speed limiter (p. 276)
* Option/accessory. 283
DRIVER SUPPORT
26 Cruise Control
27 Note: This illustration is general and details may vary depending on model.
284 * Option/accessory.
DRIVER SUPPORT
• Reactivating Cruise Control from standby Activating and starting Cruise Activating/starting Cruise Control
mode (p. 288) Control In order to start Cruise Control from standby
• Switching off Cruise Control (p. 288) The Cruise Control (CC28) function must be mode, the vehicle's current speed must be
selected and activated in order to regulate 30 km/h (20 mph) or higher. The lowest speed
speed. that can be set is 30 km/h (20 mph).
To start Cruise Control:
–
With the function displayed, press
(2) on the steering wheel keypad.
> Cruise Control will be started and the
vehicle's current speed will be set.
NOTE
Cruise control can then not be connected at
speeds below 30 km/h (20 mph).
Note: This illustration is general and details may vary Related information
depending on model. • Cruise control (p. 284)
Putting Cruise Control in standby mode
To put Cruise Control in standby mode:
–
Tap ◀ (1) or ▶ (3) and scroll to the
(4) function.
> A symbol will appear and Cruise Control
can then be activated.
28 Cruise Control
285
DRIVER SUPPORT
Managing Cruise Control speed • The most recently set speed will be stored. not affect the setting. The vehicle will return to
Cruise Control (CC29) can be set to various If speed is increased by depressing the accelera- the set speed when the accelerator pedal is
speeds. released.
tor pedal while pressing the (1) button on
the steering wheel, the vehicle's speed when the Using engine braking instead of
Setting/changing set speed button is pressed will be stored as the set speed. applying the brakes
Temporarily increasing speed using the accelera- Cruise Control regulates speed by lightly applying
tor pedal, e.g. when passing another vehicle, will the brakes. On downgrades, it can sometimes be
not affect the setting. The vehicle will return to desirable to roll a bit faster and let speed be
the set speed when the accelerator pedal is reduced instead by engine braking alone. The
released. driver can temporarily disengage the Cruise Con-
trol braking function.
For vehicles with both CC and ACC
– Change a set speed by pressing the (1) To disengage CC:
or (3) buttons briefly or by pressing and – Press the accelerator pedal about halfway
holding them: down and then release it.
• Press briefly: Press briefly: each press > Cruise Control will automatically disen-
Note: This illustration is general and details may vary changes the speed in +/- 5 mph gage the automatic brake function and
depending on model. (+/- 5 km/h) increments. speed will only be reduced using the
engine braking function.
For vehicles with only CC • Press and hold: Release the button when
– Change a set speed by pressing the (1) the set speed indicator (4) has moved to How drive mode affects cruise control
the desired speed. The way the cruise control maintains the vehicle's
or (3) buttons briefly or by pressing and
holding them: • The most recently set speed will be stored. speed can vary depending on the selected drive
mode30.
• Press briefly: Press briefly: each press If speed is increased by depressing the accelera-
changes the speed in +/- 1 mph tor pedal while pressing the (1) button on
(+/- 1 km/h) increments. the steering wheel, the vehicle's speed when the
• Press and hold: Release the button when button is pressed will be stored as the set speed.
the set speed indicator (4) has moved to Temporarily increasing speed using the accelera-
the desired speed. tor pedal, e.g. when passing another vehicle, will
29 Cruise Control
30 For more information, see "Drive modes".
286
DRIVER SUPPORT
Cruise Control Eco Cruise Deactivating and putting Cruise Standby mode due to action by the driver
In the ECO drive mode, cruise control's accelera- Control in standby mode Cruise Control will be temporarily deactivated and
tion and deceleration will be smoother than in Cruise Control (CC31) can be temporarily put put in standby mode if:
other drive modes to help provide optimal fuel
efficiency and reduced environmental impact.
into standby mode and then reactivated. • the brakes are applied
Because of this, the vehicle's actual speed may Deactivating and putting Cruise Control • the gear selector is moved to N
be slightly above or below the set speed. in standby mode • the vehicle is driven faster than the set
For more information, see "ECO drive mode" speed for more than 1 minute
under "Eco Cruise". The driver must then control the vehicle's speed.
Cruise Control Dynamic Cruise Temporarily increasing speed using the accelera-
With the Dynamic drive mode, cruise control's tor pedal, e.g. when passing another vehicle, will
acceleration and deceleration will be faster and not affect the setting. The vehicle will return to
more immediate than in other drive modes. the set speed when the accelerator pedal is
released.
Related information
Automatic standby mode
• Cruise control (p. 284)
Cruise Control will be temporarily deactivated and
put in standby mode if:
• the wheels lose traction
Note: This illustration is general and details may vary
depending on model. • the engine speed (rpm) is too low/high
To put Cruise Control in standby mode: • the temperature in the brake system
becomes too high
– Press the button on the steering wheel
• the vehicle's speed goes below 30 km/h
(2). (20 mph).
> The Cruise Control markings and symbols
The driver must then control the vehicle's speed.
will change from WHITE to GRAY, indicat-
ing that Cruise Control is temporarily Related information
deactivated and the driver needs to con- • Cruise control (p. 284)
trol the vehicle's speed.
31 Cruise Control
287
DRIVER SUPPORT
Reactivating Cruise Control from To start Cruise Control from standby mode: Switching off Cruise Control
standby mode – Cruise control (Cruise Control - CC) can be
Press the button on the steering wheel
Cruise Control (CC32) can be temporarily put (2). turned off.
into standby mode and then reactivated.
> The Cruise Control markings and symbols
Reactivating Cruise Control from in the instrument panel will change from
standby mode GRAY to WHITE and the vehicle's current
speed will be set.
WARNING
A noticeable increase in speed may follow
when the speed is resumed with the
steering wheel button.
Related information
• Cruise control (p. 284)
32 Cruise Control
288
DRIVER SUPPORT
33 Note: This illustration is general and details may vary depending on model.
34 Distance Alert }}
* Option/accessory. 289
DRIVER SUPPORT
WARNING
Distance Alert only reacts of the time interval
Distance Alert warning light on the windshield35. to the vehicle ahead is shorter than the preset
value – vehicle speed is not affected.
A warning light will appear on the windshield and
glow steadily if the time interval to the vehicle
ahead is shorter than the set time interval. NOTE
Depending on market, this function may be
NOTE either Standard or Optional. Distance Alert warning symbol on the windshield37.
Visual warnings on the windshield may be dif- For this to be possible, however, the Show
ficult to notice in cases of strong sunlight, Related information Driver Support function must be activated
reflections, extreme light contrasts, or if the • Head-up display for Distance Alert (p. 290) under Settings in the center display's menus (see
driver is wearing sunglasses or is not looking "Head-up display" for instructions).
• Activating/deactivating Distance Alert
straight ahead. (p. 291)
• Setting a time interval for Distance Alert
(p. 291)
• Distance Alert limitations (p. 292)
35 Note: This illustration is general and details may vary depending on model.
36 The Distance Alert function is only available in vehicles that can display information on the windshield with a head-up display.
37 Note: This illustration is general and details may vary depending on model.
290 * Option/accessory.
DRIVER SUPPORT
Related information
• Distance Alert* (p. 289)
38 The Distance Alert function is only available in vehicles that can display information on the windshield with a head-up display.
39 The Distance Alert function is only available in vehicles that can display information on the windshield with a head-up display. }}
* Option/accessory. 291
DRIVER SUPPORT
40 The Distance Alert function is only available in vehicles that can display information on the windshield with a head-up display.
292 * Option/accessory.
DRIVER SUPPORT
WARNING • High speeds may also result in the warn- Adaptive Cruise Control*
ing light illuminating at a shorter distance Adaptive Cruise Control (ACC41) helps the
• The radar sensor has a limited field of than the one that has been set due to driver maintain a constant speed with a set time
vision. In some situations, it may detect a limitations in the radar sensor's range.
vehicle later than expected or not detect interval to the vehicle ahead.
other vehicles at all. Adaptive Cruise Control helps provide a more
• The radar sensor cannot cover all driving NOTE relaxed driving experience on long trips on high-
situations and traffic, weather and road The function uses the vehicle's radar unit, ways or long, straight roads with even traffic
conditions. which has some general limitations – see the flows.
• The driver is responsible for maintaining a section "Radar unit limitations".
safe distance and speed and must inter-
vene if the various driver support systems Related information
do not maintain a suitable speed or suita- • Distance Alert* (p. 289)
ble distance to the vehicle ahead.
• Maintenance of radar sensor components
may only be performed by a trained and
qualified Volvo technician.
• Strong sunlight, reflections from the road
surface, strong lighting contrasts or using
sunglasses may make the warning light in
the windshield difficult to see. Poor
weather or winding roads can affect the The camera/radar sensor measures the distance to the
vehicle ahead42.
radar sensor's capacity to detect vehicles
ahead. The driver sets a speed and a time interval to the
vehicle ahead. If the camera/radar sensor detects
• A vehicle's size (e.g., a motorcycle) can
also affect the radar sensor's capacity to a slower-moving vehicle ahead, your vehicle's
detect another vehicle. This may result in speed will be automatically adapted according to
the warning light illuminating at a shorter the set time interval to that vehicle. When there
distance than the one that has been set are no longer slower-moving vehicles ahead, the
or not illuminating at all. vehicle will return to the set speed.
}}
* Option/accessory. 293
DRIVER SUPPORT
294
DRIVER SUPPORT
NOTE
In vehicles equipped with Adaptive Cruise
Control*, it is possible to switch between
cruise control and Adaptive Cruise Control –
see the heading "Switching between CC and
ACC". Speed indicators42.
Function buttons and symbols42. Set speed
42 Note: This illustration is general and details may vary depending on model. }}
* Option/accessory. 295
DRIVER SUPPORT
• Managing Adaptive Cruise Control speed Adaptive Cruise Control and WARNING
(p. 298) collision warning
Adaptive Cruise Control only issues a warning
• Setting Adaptive Cruise Control time inter- for vehicles detected by its radar unit – thus, a
vals (p. 299) warning may come after a delay or not at all.
• Deactivating/reactivating Adaptive Cruise • Never wait for a warning. Apply the
Control (p. 300) brakes when necessary.
• Passing assistance with Adaptive Cruise
Control (p. 302) Related information
• Starting passing assistance with Adaptive • Adaptive Cruise Control* (p. 293)
Cruise Control (p. 302)
• Limitations of passing assistance with Adap-
tive Cruise Control (p. 303)
• Switching target vehicles with Adaptive
Cruise Control (p. 303) Collision warning light on the windshield43.
• Automatic braking with Adaptive Cruise Con- Adaptive Cruise Control utilizes approx. 40% of
trol (p. 304) the vehicle's braking capacity. If a situation
requires more braking force than the Adaptive
• Adaptive Cruise Control limitations (p. 305)
Cruise Control can provide, and if the driver does
• Switching between Cruise Control and Adap- not apply the brakes, a warning light and audible
tive Cruise Control (p. 305) warning signal will be activated to alert the driver
• Symbols and messages for Adaptive Cruise that immediate action is required.
Control (p. 307)
NOTE
Visual warnings on the windshield may be dif-
ficult to notice in cases of strong sunlight,
reflections, extreme light contrasts, or if the
driver is wearing sunglasses or is not looking
straight ahead.
43 Note: This illustration is general and details may vary depending on model.
296 * Option/accessory.
DRIVER SUPPORT
Head-up display for Adaptive Cruise Activating and starting Adaptive Starting/activating Adaptive Cruise
Control with collision warning Cruise Control Control
In vehicles equipped with a head-up display*, a Adaptive Cruise Control (ACC45) must first be To start ACC:
flashing warning symbol will be displayed on the activated and then started before it can regulate • The driver's seat belt must be buckled and
windshield. speed and distance. the driver's door must be closed.
Putting Adaptive Cruise Control in • There must be a vehicle ahead (target vehi-
standby mode cle) within a reasonable distance or your
vehicle's current speed must be at least
15 km/h (9 mph).
NOTE
Note: This illustration is general and details may vary
Visual warnings on the windshield may be dif- depending on model.
ficult to notice in cases of strong sunlight, Note: This illustration is general and details may vary
Adaptive Cruise Control is in standby mode each
reflections, extreme light contrasts, or if the depending on model.
time the engine is started. To put ACC in standby
driver is wearing sunglasses or is not looking
mode from active mode:
straight ahead.
– Press ◀ (2) or ▶ (3) on the steering wheel
Related information keypad and scroll to the (4) function.
• Adaptive Cruise Control* (p. 293) > The symbol will appear and Adaptive
Cruise Control will go into standby mode.
44 Note: This illustration is general and details may vary depending on model.
45 Adaptive Cruise Control }}
* Option/accessory. 297
DRIVER SUPPORT
|| – With the (4) function displayed, press Managing Adaptive Cruise Control – Change a set speed by pressing the (1)
(1) on the steering wheel keypad. speed or (2) buttons briefly or by pressing and
> Adaptive Cruise Control will start and the Adaptive Cruise Control (ACC46) can be set to holding them:
current speed will be stored, which will be various speeds.
• Press briefly: Press briefly: each press
shown by numbers in the center of the changes the speed in +/- 5 mph
Setting/changing set speed
speedometer. (+/- 5 km/h) increments.
ACC will only regulate the time • Press and hold: Release the button when
interval to the vehicle ahead the set speed indicator (3) has moved to
when the distance symbol the desired speed.
shows two vehicles.
• The most recently set speed will be stored.
If speed is increased by depressing the accelera-
tor pedal while pressing the button on the
A speed interval will be marked steering wheel, the vehicle's speed when the but-
at the same time. ton is pressed will be stored as the set speed.
The higher speed is the set Temporarily increasing speed using the accelera-
speed for your vehicle and the tor pedal, e.g. when passing another vehicle, will
lower speed is the speed of the Note: This illustration is general and details may vary not affect the setting. The vehicle will return to
vehicle ahead (target vehicle). depending on model and market.
the set speed when the accelerator pedal is
Related information : Increases the set speed. released.
• Adaptive Cruise Control* (p. 293)
: Reduces the set speed.
Set speed.
298 * Option/accessory.
DRIVER SUPPORT
Distance indicator
NOTE
– Press the (1) or (2) button to decrease or
When the symbol in the instrument panel
increase the time interval.
shows two vehicles, ACC is following the vehi-
cle ahead at a preset time interval. > The distance indicator (3) shows the cur-
rent time interval.
When only one vehicle is shown, there is no
vehicle ahead within a reasonable distance. In order to help your vehicle follow the vehicle
ahead as smoothly and comfortably as possible,
Adaptive Cruise Control allows the time interval
to vary noticeably in certain situations. At low
speeds, when the distance to the vehicle ahead
is short, Adaptive Cruise Control increases the
time interval slightly.
* Option/accessory. 299
DRIVER SUPPORT
300 * Option/accessory.
DRIVER SUPPORT
To temporarily deactivate Adaptive Cruise Control Temporarily increasing speed using the accelera- • the driver opens the door.
and put it in standby mode: tor pedal, e.g. when passing another vehicle, will • the driver unbuckles the seat belt.
not affect the setting. The vehicle will return to
– Press the button on the steering wheel the set speed when the accelerator pedal is • the engine speed (rpm) is too low/high.
(2). released. • one or more of the wheels lose traction.
> The symbol in the instrument panel Automatic standby mode • the brake temperature is high.
changes color from WHITE to GRAY and
the set speed in the center of the speed-
Adaptive Cruise Control is dependent on other • the parking brake is applied.
systems, such as Electronic Stability Control
ometer will change from BEIGE to GRAY. • the camera/radar sensor is covered by snow
(ESC50). If any of these other systems stops or heavy rain (the camera lens/radar waves
working, Adaptive Cruise Control will automati- are blocked)
WARNING cally switch off.
• If Adaptive Cruise Control is in standby Reactivating Adaptive Cruise Control
mode, the driver must intervene and regu- WARNING from standby mode
late both speed and distance to the vehicle With automatic standby mode, the driver is
ahead. warned by an acoustic signal and a message
• If the vehicle comes too close to a vehicle on the instrument panel.
ahead when Adaptive Cruise Control is in • The driver must then regulate vehicle
standby mode, the driver is instead warned speed, apply the brakes if necessary, and
of the short distance by the Distance Alert maintain a safe distance to other vehicles.
function.
Adaptive Cruise Control may go into standby
Standby mode due to action by the driver mode if:
Adaptive Cruise Control will be temporarily deac- • your vehicle's speed goes below 5 km/h
tivated and put in standby mode if: (3 mph) and ACC cannot determine if the
vehicle ahead is stationary or if it is another Note: This illustration is general and details may vary
• the brakes are applied. depending on model.
object, e.g. a speed bump.
• the gear selector is moved to N
• your vehicle's speed goes under 5 km/h
• the vehicle is driven faster than the set (3 mph) and the vehicle ahead turns so that
speed for more than 1 minute ACC no longer has a vehicle to follow.
301
DRIVER SUPPORT
|| To reactivate ACC from standby mode: Passing assistance with Adaptive Starting passing assistance with
–
Cruise Control Adaptive Cruise Control
Press the button on the steering wheel
(1). Adaptive Cruise Control (ACC51) can assist the
driver when passing other vehicles. Requirements for passing assistance
> Speed will be set to the most recently In order to activate passing assistance:
stored speed. How passing assistance works • your vehicle must be following a vehicle
When ACC is following another vehicle and you ahead (target vehicle)
WARNING indicate that you intend to pass that vehicle by
using the turn signal52, Adaptive Cruise Control • your vehicle's current speed must be
A noticeable increase in speed may follow at least 70 km/h (43 mph)
when the speed is resumed with the will begin accelerating toward the vehicle ahead
steering wheel button. before your vehicle has moved into the passing • the set speed for ACC must be high
lane. enough to safely pass another vehicle.
Related information The function will then delay a speed reduction to Starting parking assistance
• Adaptive Cruise Control* (p. 293) avoid early braking as your vehicle approaches a To start passing assistance:
slower-moving vehicle.
– Turn on the left turn signal.
The function remains active until your vehicle has
> Passing assistance will start.
passed the other vehicle.
Related information
WARNING • Adaptive Cruise Control* (p. 293)
Please note that this function can be acti-
vated in more situations than just passing
another vehicle, such as when a direction indi-
cator is used to indicate a lane change or
before exiting to another road – the vehicle
will then briefly accelerate.
Related information
• Adaptive Cruise Control* (p. 293)
302 * Option/accessory.
DRIVER SUPPORT
* Option/accessory. 303
DRIVER SUPPORT
Automatic braking with Adaptive NOTE This occurs if Adaptive Cruise Control is keeping
Cruise Control the vehicle stationary using the brakes and:
ACC can keep the vehicle stationary for no
The Adaptive cruise control (ACC55) has a spe- more than 5 minutes – after that time the • the driver opens the door or unbuckles
cial brake function in slow traffic and while sta- parking brake is applied and Adaptive Cruise his/her seat belt
tionary. Control is deactivated. • ACC has kept the vehicle at a standstill for
Braking function in slow traffic and at a more than approx. 5 minutes
The parking brake must be released before
standstill Adaptive Cruise Control can be reactivated. • the brakes overheat
In slow-moving, stop-and-go traffic or when stop- • the driver switches off the engine manually.
ped at a traffic light, driving will resume automati- Deactivation of the Auto-hold brake function
cally if the vehicle is stopped for less than Related information
In certain situations, Auto-hold will be deactivated
approx. 3 seconds. If it takes more than 3 sec- when the vehicle is at a standstill and Adaptive
• Adaptive Cruise Control* (p. 293)
onds for the vehicle ahead to begin moving again, Cruise Control will go into standby mode. This
Adaptive Cruise Control will go into standby means that the brakes will be released and the
mode and the Auto-hold brake function will acti- vehicle could begin to roll. The driver must
vate. actively apply the brakes to keep the vehicle sta-
– Adaptive Cruise Control can be reactivated in tionary.
one of the following ways: This can occur if:
• Pressing the button on the steering • the driver depresses the brake pedal
wheel keypad.
• the parking brake is applied
• Pressing the accelerator pedal.
• the gear selector is moved to the P, N or R
> Adaptive Cruise Control will resume fol- positions
lowing the vehicle ahead if it begins to
move within approx. 6 seconds. • the driver puts Adaptive Cruise Control in
standby mode.
304 * Option/accessory.
DRIVER SUPPORT
Adaptive Cruise Control limitations Related information Switching between Cruise Control
Adaptive Cruise Control (ACC56) may have lim- • Adaptive Cruise Control* (p. 293) and Adaptive Cruise Control
ited functionality in certain situations. In vehicles equipped with Adaptive Cruise Con-
trol (ACC57), the driver can switch between
Steep roads and/or heavy loads Cruise Control (CC58) and ACC.
Adaptive Cruise Control is primarily intended to
be driven on flat roads. The function may not be A symbol in the instrument panel indicates which
able to maintain the correct time interval to the cruise control system is active
vehicle ahead when driving down steep hills. The
CC ACC
driver should be extra attentive and prepared to
apply the brakes.
A A
• Do not use Adaptive Cruise Control if the
vehicle is carrying a heavy load or towing a Cruise control Adaptive Cruise Control
trailer.
A WHITE symbol: The function is active. GRAY symbol: Standby
mode
Other limitations
• The Off Road drive mode cannot be Switching from ACC to CC
selected if Adaptive Cruise Control is acti- To do so:
vated.
1. Press the button on the steering wheel
keypad to put Adaptive Cruise Control in
NOTE standby mode.
The function uses the vehicle's camera unit,
which has some general limitations – see the
section "Camera unit limitations".
NOTE
The function uses the vehicle's radar unit,
which has some general limitations – see the
section "Radar unit limitations".
* Option/accessory. 305
DRIVER SUPPORT
|| 2. Tap the Cruise Control button in the center Switching from CC to ACC
display's Function view. The button's indica- To do so:
tor will change from GRAY to GREEN.
1. Press the button on the steering wheel
> The symbol in the instrument panel will
keypad to put Cruise Control in standby
change from ACC to mode.
CC, indicating that Adaptive Cruise Con- 2. Tap the Cruise Control button in Function
trol is off and Cruise Control is in standby view. The button's indicator will change from
mode. GREEN to GRAY.
3. Pressing the button on the steering > The symbols in the instrument panel will
wheel keypad.
switch from CC to ACC
> Cruise Control will start and the vehicle's to indicate that Adaptive Cruise Control is
current speed will be set. in standby mode.
306 * Option/accessory.
DRIVER SUPPORT
Symbols and messages for The previous illustration61 shows that Adaptive vehicle ahead, which is traveling at the same
Adaptive Cruise Control Cruise Control is set to maintain a speed of speed.
A number of symbols and messages relating to 110 km/h (68 mph) and that there is no target
Adaptive Cruise Control (ACC59) may be dis- vehicle ahead to follow.
played in the instrument panel and/or the head-
up display*.
* Option/accessory. 307
DRIVER SUPPORT
Related information
• Adaptive Cruise Control* (p. 293)
308 * Option/accessory.
DRIVER SUPPORT
Pilot Assist The driver sets the desired speed and distance to The color of the steering wheel
Pilot Assist helps the driver keep the vehicle in the vehicle ahead. Pilot Assist monitors the dis- symbol indicates the current
the current traffic lane by providing steering tance to the vehicle ahead and the traffic lane's status of steering assistance:
assistance and maintaining an even speed and a side markers using the camera and radar sensor.
• GREEN indicates that steer-
set time interval to the vehicle ahead. The system maintains the set time interval to the
ing assistance is active
vehicle ahead by automatically adjusting your
How Pilot Assist works vehicle's speed and keeps your vehicle in its lane • GRAY (as shown in illustra-
The Pilot Assist function is primarily intended for by providing steering assistance. tion) indicates that steering assistance is deacti-
use on highways and other major roads where it vated.
Pilot Assist's steering assistance is based on
can help provide a more comfortable and relaxing
monitoring the direction of the vehicle ahead and
driving experience.
the traffic lane's side marker lines. The driver can
override Pilot Assist's steering recommendations
at any time and steer in another direction, e.g. to
change lanes or avoid obstacles on the road.
If the camera/radar sensor cannot detect the
lane's side marker lines or if Pilot Assist is unable
for some other reason to clearly interpret the
lane, Pilot Assist will temporarily deactivate steer-
ing assistance until it can once again interpret
the lane markings. However, the speed and dis-
tance warnings will remain active.
WARNING
The camera/radar sensor monitors the distance to the
vehicle ahead and detects lane markings62. Pilot Assist is deactivated automatically and
resumes working without prior notice.
Camera and radar sensor
Distance monitor
62 Note: This illustration is general and details may vary depending on model. }}
309
DRIVER SUPPORT
310
DRIVER SUPPORT
When the vehicle is approaching an off-ramp or a Overview Increases the time interval to the vehicle
fork in the road, the driver should steer toward ahead
Controls
the desired lane to indicate to Pilot Assist the ▶: Switches from Adaptive Cruise Control to
desired direction of travel. Pilot Assist
Pilot Assist strives to keep the vehicle Reduces the time interval to the vehicle
in the center of the lane ahead
When Pilot Assist provides steering assistance, it Function symbol
strives to position the vehicle in the center of the
lane between the lane markings. For the smooth- Symbols for target vehicle and distance to
est driving experience possible, the driver should the vehicle ahead
permit the vehicle to find the optimal positioning. Symbol for activated/deactivated steering
The driver should check that the vehicle is posi- assistance
tioned safely in the lane and can always adjust
the vehicle's position by applying more force to
the steering wheel. Function buttons and symbols62.
If Pilot Assist does not position the vehicle appro- : Activates Pilot Assist from standby
priately in the lane, the driver should turn off Pilot mode and resumes the set speed and time
Assist or switch to Adaptive Cruise Control. interval
: Increases the set speed
62 Note: This illustration is general and details may vary depending on model. }}
311
DRIVER SUPPORT
|| Instrument panel • Setting a time interval for Pilot Assist Pilot Assist and collision warning
(p. 315)
• Deactivating/reactivating Pilot Assist Collision warning
(p. 317)
• Passing assistance with Pilot Assist (p. 319)
• Starting passing assistance with Pilot Assist
(p. 319)
• Passing assistance with Pilot Assist limita-
tions (p. 319)
• Switching target vehicles with Pilot Assist
(p. 320)
Speed indicators62.
• Automatic braking with Pilot Assist (p. 320)
62 Note: This illustration is general and details may vary depending on model.
63 The illustration is generic - details may vary according to vehicle model.
312 * Option/accessory.
DRIVER SUPPORT
NOTE Head-up display for Pilot Assist Activating and starting Pilot Assist
during collision risks Pilot Assist must first be activated and then
Visual warnings on the windshield may be dif-
In vehicles equipped with a head-up display*, a started before it can regulate speed and dis-
ficult to notice in cases of strong sunlight,
flashing warning symbol will be displayed on the tance and provide steering assistance.
reflections, extreme light contrasts, or if the
windshield.
driver is wearing sunglasses or is not looking
straight ahead.
WARNING
Pilot Assist only issues a warning for vehicles
detected by its camera and radar unit – thus,
a warning may come after a delay or not at all.
• Never wait for a warning. Apply the
brakes when necessary!
Related information
Note: This illustration is general and details may vary
• Pilot Assist (p. 309) Collision warning symbol on the windshield64. depending on model.
To start Pilot Assist:
NOTE
Visual warnings on the windshield may be dif- • The driver's seat belt must be buckled and
ficult to notice in cases of strong sunlight, the driver's door must be closed.
reflections, extreme light contrasts, or if the • There must be a vehicle ahead (target vehi-
driver is wearing sunglasses or is not looking cle) within a reasonable distance or your
straight ahead. vehicle's current speed must be at least
15 km/h (9 mph).
Related information
• Pilot Assist (p. 309)
64 Note: This illustration is general and details may vary depending on model. }}
* Option/accessory. 313
DRIVER SUPPORT
|| With Adaptive Cruise Control in standby mode: A speed interval will be marked Managing Pilot Assist speed
at the same time.
1. Press the ▶ button on the steering wheel (6). Pilot Assist can be set to various speeds.
> The The higher speed is the set
symbol will change to Pilot Setting/changing set speed
speed for your vehicle and the
Assist in standby mode (8).
lower speed is the speed of the
2. Press the button on the steering wheel vehicle ahead (target vehicle).
(2).
Hands on the steering wheel
> Pilot Assist will start and the current
Pilot Assist only functions if the driver's hands
speed will be stored, which will be shown
are on the steering wheel. If Pilot Assist detects
by numbers in the center of the speedom-
that the driver's hands are not on the steering
eter.
wheel, the driver will be instructed to actively
...or... steer the vehicle by a text message and an audi-
ble signal.
With Adaptive Cruise Control started:
If Pilot Assist still cannot detect the driver's
– Press the ▶ button on the steering wheel (6).
hands on the steering wheel, the function will go
> Pilot Assist will start. Note: This illustration is general and details may vary
into standby mode. Pilot Assist must then be depending on model and market.
Pilot Assist's steering assis- reactivated by pressing the button on the
tance is only active when the steering wheel. : Increases the set speed
steering wheel symbol (2)
changes from GRAY to : Reduces the set speed
NOTE
GREEN. Set speed
Note that the Pilot Assist function only works
Pilot Assist will only regulate when the driver's hands are on the steering
the time interval to the vehicle ahead when the wheel.
distance symbol shows a vehicle (1) over the
steering wheel symbol.
Related information
• Pilot Assist (p. 309)
314
DRIVER SUPPORT
– Change a set speed by pressing the (1) The highest possible speed that can be set is Setting a time interval for Pilot
or (2) buttons briefly or by pressing and 200 km/h (125 mph). Assist
holding them: Pilot Assist can be set to different time intervals.
Related information
• Press briefly: Press briefly: each press • Pilot Assist (p. 309) Different time intervals to the
changes the speed in +/- 5 mph vehicle ahead can be selected
(+/- 5 km/h) increments. and are shown in the instru-
• Press and hold: Release the button when ment panel as 1–5 horizontal
the set speed indicator (3) has moved to bars. The more bars, the longer
the desired speed. the time interval. One bar rep-
resents an interval of
• The most recently set speed will be stored. approx. 1 second to the vehicle ahead. 5 bars
If speed is increased by depressing the accelera- represents approx. 3 seconds.
tor pedal while pressing the button on the
steering wheel, the vehicle's speed when the but- NOTE
ton is pressed will be stored as the set speed.
When the symbol in the instrument panel
Temporarily increasing speed using the accelera- shows a vehicle and a steering wheel, Pilot
tor pedal, e.g. when passing another vehicle, will Assist follows a vehicle ahead at a preset
not affect the setting. The vehicle will return to time interval.
the set speed when the accelerator pedal is
When only a steering wheel is shown, there is
released.
no vehicle ahead within a reasonable dis-
Automatic transmission tance.
Pilot Assist can follow another vehicle at speeds
from a standstill up to 200 km/h (125 mph).
The lowest speed that can be set for Pilot Assist
is 30 km/h (20 mph). When following another
vehicle, ACC can monitor that vehicle's speed
and slow your own vehicle down to a standstill,
but it is not possible to set speeds lower than
30 km/h (20 mph).
}}
315
DRIVER SUPPORT
• The greater the vehicles' speed, the • Eco - Pilot Assist will focus on providing
greater the distance between them for a optimal fuel economy, which will increase the
set time interval. time interval to the vehicle ahead.
• Only use the time intervals permitted by • Comfort - Pilot Assist will focus on following
local traffic regulations. the set time interval to the vehicle ahead as
smoothly as possible.
• If Pilot Assist does not seem to respond
with a speed increase when activated, it • Dynamic - Pilot Assist will focus on follow-
may be because the time interval to the ing the set time interval to the vehicle ahead
vehicle ahead is shorter than the set time more exactly, which could mean faster accel-
interval. eration and heavier braking.
Controls for setting a time interval65. For more information, see "Drive modes".
Reduce the time interval Additional information is provided in the sections
WARNING
Increase the time interval "Managing Cruise Control speed" and "ECO
• Only use a time interval suitable for the drive mode".
current traffic conditions.
Distance indicator
• The driver should be aware that short Related information
– Press the (1) or (2) button to decrease or time intervals give them limited time to • Pilot Assist (p. 309)
increase the time interval. react and act to any unforeseen traffic
> The distance indicator (3) shows the cur- situation.
rent time interval.
In order to follow the vehicle ahead as smoothly Setting how Pilot Assist should
as possible, Pilot Assist allows the time interval to maintain distance* to the vehicle ahead
vary considerably in certain situations. For exam- The driver can choose different drive modes to
ple, at low speeds and short distances to the determine how Pilot Assist should maintain a
vehicle ahead, Pilot Assist increases the time time interval to the vehicle ahead. Settings are
interval slightly. made using the DRIVE MODE controls.
65 Note: This illustration is general and details may vary depending on model.
316 * Option/accessory.
DRIVER SUPPORT
Deactivating/reactivating Pilot ...or... the set speed when the accelerator pedal is
Assist – Press the ◀ button on the steering wheel (3).
released.
Pilot Assist can be temporarily put into standby > Pilot Assist is turned off and Adaptive When the turn signals are used, Pilot Assist's
mode and then reactivated. Cruise Control will go into active mode. steering assistance will be temporarily deacti-
vated. When the turn signal is switched off, steer-
Deactivating and putting Pilot Assist in ing assistance will be automatically reactivated if
standby mode WARNING
the traffic lane's side markings can still be
• With Pilot Assist in standby mode, the detected.
driver must intervene and steer and regu-
late both speed and distance to the vehi-
cle ahead.
• If the vehicle comes too close to a vehicle
ahead when Pilot Assist is in standby
mode, the driver is instead warned of the
short distance by the Distance Alert func-
tion.
}}
317
DRIVER SUPPORT
|| Automatic standby mode • your vehicle's speed goes below 5 km/h WARNING
Pilot Assist is dependent on other systems, such (3 mph) and Pilot Assist cannot determine if
the vehicle ahead is stationary or if it is A noticeable increase in speed may follow
as Electronic Stability Control (ESC66). If any of
these other systems stops working, Pilot Assist another object, e.g. a speed bump. when the speed is resumed with the
steering wheel button.
will automatically switch off. • your vehicle's speed goes under 5 km/h
(3 mph) and the vehicle ahead turns so that
WARNING Pilot Assist no longer has a vehicle to follow. Related information
• Pilot Assist (p. 309)
With automatic standby mode, the driver is Reactivating Pilot Assist from standby
warned by an acoustic signal and a message
on the instrument panel. mode
318
DRIVER SUPPORT
Passing assistance with Pilot Assist Starting passing assistance with Passing assistance with Pilot Assist
Pilot Assist can assist the driver when passing Pilot Assist limitations
other vehicles. Passing assistance functionality may be reduced
Requirements for passing assistance in certain situations.
How passing assistance works In order to activate passing assistance:
When Pilot Assist is following another vehicle WARNING
and you indicate that you intend to pass that
• your vehicle must be following a vehicle
The driver should be aware that if conditions
ahead (target vehicle) suddenly change when using Parking Assis-
vehicle by using the turn signal67, Pilot Assist will
begin accelerating toward the vehicle ahead • your vehicle's current speed must be tance, the function may implement an unde-
at least 70 km/h (43 mph) sired acceleration in certain conditions.
before your vehicle has moved into the passing
lane. • the set speed for Pilot Assist must be high Some situations should be avoided, e.g. if:
enough to safely pass another vehicle. • the vehicle is approaching an exit in the
The function will then delay a speed reduction to
avoid early braking as your vehicle approaches a same direction as passing would normally
Starting parking assistance
slower-moving vehicle. occur
To start passing assistance:
The function remains active until your vehicle has • the vehicle ahead slows before your vehi-
– Turn on the left turn signal. cle has had time to switch to the passing
passed the other vehicle.
> Passing assistance will start. lane
WARNING Related information • traffic in the passing lane slows down
Please note that this function can be acti- • Pilot Assist (p. 309) • a vehicle for right-hand traffic is driven in
vated in more situations than just passing a country with left-hand traffic (or vice
another vehicle, such as when a direction indi- versa).
cator is used to indicate a lane change or
before exiting to another road – the vehicle
will then briefly accelerate. Situations of this type can be avoided by tempo-
rarily putting Pilot Assist in standby mode.
67 Only the left-hand turn signal for left-hand drive vehicles, or right-hand turn signal for right-hand drive vehicles.
319
DRIVER SUPPORT
Switching target vehicles with Pilot WARNING Automatic braking with Pilot Assist
Assist Pilot Assist has a special braking function in
When Pilot Assist follows another vehicle at
At certain speeds, models with automatic trans- speeds over approx. 30 km/h (20 mph) and slow traffic and at a standstill.
missions and Pilot Assist can switch target vehi- changes target vehicle – from a moving vehi-
cles. cle to a stationary one – Pilot Assist will Braking function in slow traffic and at a
ignore the stationary vehicle and instead standstill
Switching target vehicles accelerate to the stored speed. In slow-moving, stop-and-go traffic or when stop-
ped at a traffic light, driving will resume automati-
• The driver must then intervene and apply
cally if the vehicle is stopped for less than
the brakes.
approx. 3 seconds. If it takes more than 3 sec-
onds for the vehicle ahead to begin moving again,
Automatic standby mode when switching Pilot Assist will go into standby mode and the
targets Auto-hold brake function will activate.
Pilot Assist disengages and goes into standby
– Pilot Assist can be reactivated by:
mode if:
• your vehicle's speed goes below 5 km/h • Pressing the button on the steering
If the target vehicle ahead turns suddenly, there may be (3 mph) and Pilot Assist cannot determine if wheel keypad.
stationary traffic ahead.
the target object is a stationary vehicle or • Pressing the accelerator pedal.
When Pilot Assist is actively following another another object, e.g. a speed bump. > Pilot Assist will resume following the vehi-
vehicle at speeds under 30 km/h (20 mph) and • your vehicle's speed goes under 5 km/h cle ahead if it begins to move within
switches targets from a moving vehicle to a sta- (3 mph) and the vehicle ahead turns so that approx. 6 seconds.
tionary vehicle, Pilot Assist will brake for the sta- Pilot Assist no longer has a vehicle to follow.
tionary vehicle.
NOTE
Related information
• Pilot Assist (p. 309) Pilot Assist can keep the vehicle stationary
for no more than 5 minutes – after that time
the parking brake is applied and the function
is deactivated.
The parking brake must be released before
Pilot Assist can be reactivated.
320
DRIVER SUPPORT
321
DRIVER SUPPORT
|| The driver is responsible for ensuring that be extra attentive and prepared to apply the Pilot Assist* symbols and messages
the vehicle maintains a suitable distance brakes. A number of symbols and messages relating to
from such obstacles.
• Do not use Pilot Assist if the vehicle is carry- Pilot Assist may be displayed in the instrument
• The camera and radar sensors do not ing a heavy load or towing a trailer. panel and/or the head-up display*.
have the capacity to detect all oncoming
objects and obstacles in traffic environ- NOTE
ments, e.g. potholes, stationary obstacles
or objects that completely or partially Pilot Assist cannot be activated if a trailer,
block the route. bike carrier or similar is connected to the
vehicle electrical system.
• Pilot Assist does not "see" pedestrians,
animals, etc.
Other limitations
• The recommended steering input is lim-
ited in force, which means that it cannot • The Off Road drive mode cannot be
always help the driver to steer and keep selected when Pilot Assist is activated.
the vehicle within the lane.
NOTE
• Pilot Assist is switched off if the power
steering is working with reduced power - The function uses the vehicle's camera unit,
e.g. during cooling due to overheating which has some general limitations – see the
(see section "Speed-dependent steering section "Camera unit limitations".
force").
NOTE
The driver can always correct or adjust steering The function uses the vehicle's radar unit,
assistance provided by Pilot Assist by turning the which has some general limitations – see the
steering wheel to the desired position. section "Radar unit limitations".
Steep roads and/or heavy loads
Pilot Assist is primarily intended to be driven on Related information
flat roads. The function may not be able to main- • Pilot Assist (p. 309)
tain the correct time interval to the vehicle ahead
• Speed-dependent steering wheel resistance
when driving down steep hills. The driver should (p. 270)
322 * Option/accessory.
DRIVER SUPPORT
The previous illustration69 shows that Pilot Assist The previous illustration69 shows that Pilot Assist
is set to maintain a speed of 110 km/h (68 mph) is set to maintain a speed of 110 km/h (68 mph)
The previous illustration69 shows that Pilot Assist
and is following a target vehicle ahead that is and is following a target vehicle ahead that is
is set to maintain a speed of 110 km/h (68 mph)
traveling at the same speed. traveling at the same speed.
and that there is no target vehicle ahead to fol-
low. Pilot Assist will not provide any steering assis- In this example, Pilot Assist will also provide
tance because it cannot detect the lane's side steering assistance because it can detect the
Pilot Assist will not provide any steering assis-
marking lines. lane's side marking lines.
tance because it cannot detect the lane's side
marking lines.
68 In the following illustration, Road Sign Information (RSI) indicates that the maximum permitted speed is 130 km/h (80 mph).
69 Note: This illustration is general and details may vary depending on model. }}
323
DRIVER SUPPORT
69 Note: This illustration is general and details may vary depending on model.
324 * Option/accessory.
DRIVER SUPPORT
Radar sensor limitations The radar sensor is located on the upper interior If this symbol and the message
The radar sensor used by several of the driver section of the windshield along with the camera. "Windscreen sensor Sensor
support functions has certain limitations, which blocked, see Owner's manual" is
also affect the functions using the radar sensor. CAUTION displayed in the instrument panel, it
means that the camera and radar sensor are
Obstructed camera Do not place, affix or mount anything on the unable to detect other vehicles, cyclists, pedes-
inside or outside of the windshield, or in front trians and large animals in front of the vehicle
of or around the camera and radar unit – this and that the vehicle's camera and radar-based
could disrupt camera and radar-based func- functions may be obstructed, reduced, completely
tions. disabled or providing inaccurate responses.
It could cause functions to be reduced, deac-
tivated completely or produce an incorrect
function response.
The following table shows some of the situations that can cause the message to be displayed, and suggested actions:
Cause Action
The area of the windshield in front of the camera/radar sensor is dirty or Clean the windshield in front of the camera/radar sensor and remove dirt, ice
covered by ice or snow. and snow.
Thick fog, heavy rain or snow is blocking the radar signals or the camera's No action. Heavy precipitation may sometimes prevent the camera/radar sensor
range of visibility. from functioning.
70 Note: This illustration is general and details may vary depending on model. }}
325
DRIVER SUPPORT
|| Cause Action
Water or snow is spraying/swirling up and blocking the radar signals or No action. Very wet or snow-covered roads may sometimes prevent the cam-
the camera's range of visibility. era/radar sensor from functioning.
There is dirt between the inside of the windshield and the camera/radar Consult a workshop to have the area of the windshield on the inside of the cam-
sensor. era's casing cleaned. An authorized Volvo workshop is recommended.
326
DRIVER SUPPORT
327
DRIVER SUPPORT
Recommended maintenance for the Radar sensor type approval Note: Changes or modifications not expressively
radar sensor The type approval for the vehicle radar sensor in approved by the party responsible for compliance
In order for the camera/radar sensor to function the ACC71, PA72 and BLIS73 functions can be could void the user's authority to operate the
properly, the area of the windshield in front of the read here. equipment. The term “IC:” before the radio
unit must be kept free of dirt, ice, snow, etc. and certification number only signifies that Industry
should be washed regularly with water and car ACC71, PA72 and BLIS73 Canada technical specifications were met.
washing detergent. USA & Canada: Note: This equipment complies with radiation
FCC ID: L2C0054TR IC: 3432A-0054TR exposure limits set forth for an uncontrolled
NOTE environment. This equipment should be installed
FCC ID: L2C0055TR IC: 3432A-0055TR and operated with minimum distance of 20 cm
Dirt, ice and snow covering the camera and
This device complies with Part 15 of the FCC between the radiator and your body.
radar unit reduce their function and can make
measurement impossible. Rules and with Industry Canada license-exempt
RSS standard(s). Related information
It could cause functions to be reduced, deac- • Radar sensor (p. 324)
tivated completely or produce an incorrect Operation is subject to the following two
function response. conditions:
(1) This device may not cause harmful
Related information interference, and
• Radar sensor (p. 324) (2) This device must accept any interference
received, including interference that may cause
undesired operation.
Cet appareil est conforme aux CNR d’Industrie
Canada a applicables aux appareils radio
exempts de licence. L’exploitation est autorisée à
condition que l'appareil ne produise pas de
brouillage préjudiciable et qu'il accepte tout
brouillage, même celui susceptible d'en
compromettre le fonctionnement.
328
DRIVER SUPPORT
* Option/accessory. 329
DRIVER SUPPORT
74 Note: This illustration is general and details may vary depending on model.
330
DRIVER SUPPORT
Cause Action
The area of the windshield in front of the camera/radar sensor is Clean the windshield in front of the camera/radar sensor and remove dirt, ice and
dirty or covered by ice or snow. snow.
Thick fog, heavy rain or snow is blocking the radar signals or the No action. Heavy precipitation may sometimes prevent the camera/radar sensor from
camera's range of visibility. functioning.
Water or snow is spraying/swirling up and blocking the radar signals No action. Very wet or snow-covered roads may sometimes prevent the camera/
or the camera's range of visibility. radar sensor from functioning.
There is dirt between the inside of the windshield and the camera/ Consult a workshop to have the area of the windshield on the inside of the camera's
radar sensor. casing cleaned. An authorized Volvo workshop is recommended.
Bright sunlight No action. The camera/radar sensor will reset automatically when lighting conditions
improve.
}}
331
DRIVER SUPPORT
CAUTION
If the windshield is replaced, the camera and
radar unit must be recalibrated by a workshop
to help ensure proper functioning of all of the
vehicle's camera and radar-based systems –
an authorized Volvo workshop is recom-
mended.
Related information
• Camera (p. 329)
332
DRIVER SUPPORT
Recommended maintenance for the City Safety™ changes in the traffic ahead and driver distraction
camera/radar sensor City Safety can alert the driver with light, sound could lead to an incident.
In order for the camera/radar sensor to function and pulsations in the brake pedal to help the The function assists the driver by automatically
properly, the area of the windshield in front of the driver detect pedestrians, cyclists, large animals applying the brakes if there is an imminent risk of
unit must be kept free of dirt, ice, snow, etc. and and vehicles that appear suddenly – the vehicle a collision and the driver does not react in time by
should be washed regularly with water and car will then attempt to automatically brake if the braking and/or steering away.
washing detergent. driver does not act within a reasonable amount
of time. City Safety activates a brief, forceful braking in an
attempt to stop your vehicle immediately behind
NOTE the vehicle or object ahead.
Dirt, ice and snow covering the camera and City Safety is activated in situations in which the
radar unit reduce their function and can make driver should have applied the brakes much ear-
measurement impossible. lier, which means that the system will not be able
It could cause functions to be reduced, deac- to assist the driver in all situations.
tivated completely or produce an incorrect City Safety is designed to be activated as late as
function response. possible to help avoid unnecessary intervention.
Normally, the occupants of the vehicle will not be
Related information aware of City Safety except when the system
• Camera (p. 329) intervenes when a collision is imminent.
75 Note: This illustration is general and details may vary depending on model. }}
333
DRIVER SUPPORT
|| WARNING • The driver is advised to read all sections City Safety parameters and sub-
in the Owner's Manual that relate to City functions
• The City Safety function is supplementary Safety to learn about factors such as its City Safety can help avoid a collision with a vehi-
driver support intended to help improve limitations and what the driver should be cle, cyclist or large animal ahead by reducing the
driving safety – it cannot handle all situa- aware of before using the system (see vehicle's speed using its automatic braking func-
tions in all traffic, weather and road condi- the list of links for all subsections). tion.
tions.
If the difference in speed is greater than the
• The City Safety auto-brake function can Related information
prevent a collision or reduce collision speeds specified below, the City Safety auto-
• City Safety parameters and sub-functions brake function cannot prevent a collision, but it
speed, but to ensure full brake perform- (p. 334)
ance the driver should always depress the can help mitigate its effects.
brake pedal – even when the car auto- • Setting a warning distance for City Safety
Vehicles
brakes. (p. 336)
City Safety can help prevent a collision with a
• The warning and steering assistance are • Detecting obstacles with City Safety (p. 337) vehicle ahead by reducing your vehicle's speed
only activated if there is a high risk of col- • City Safety in crossing traffic (p. 339) by up to 60 km/h (37 mph).
lision – you must therefore never wait for • Limitations of City Safety in crossing traffic Cyclists
the collision warning or City Safety to (p. 340) City Safety can help prevent a collision with a
intervene. cyclist ahead by reducing your vehicle's speed by
• City Safety and delayed evasive maneuvers
• Warnings and brake interventions for (p. 341) up to 50 km/h (30 mph).
pedestrians and cyclists are disengaged Pedestrians
at vehicle speeds over 80 km/h • City Safety limitations (p. 342)
City Safety can help prevent a collision with a
(50 mph). • City Safety messages (p. 344)
pedestrian ahead by reducing your vehicle's
• City Safety does not activate auto-braking speed by up to 45 km/h (28 mph).
intervention during heavy acceleration.
• City Safety is not a substitute for the driv-
er's attention and judgment. The driver is
always responsible for ensuring the vehi-
cle is driven in a safe manner, at the
appropriate speed, with an appropriate
distance to other vehicles, and in accord-
ance with current traffic rules and regula-
tions.
334
DRIVER SUPPORT
Large animals City Safety carries out three steps in the follow- 2 - Brake assistance
If there is a risk of colliding with a large animal, ing order: If the risk of a collision increases after the colli-
City Safety can help reduce your vehicle's speed 1. Collision warning sion warning, brake support will be activated.
by up to 15 km/h (9 mph).
2. Brake assistance If the system determines that the pressure the
The braking function for large animals is primarily driver is exerting on the brake pedal is insufficient
3. Auto-brake
intended to mitigate the force of a collision at to prevent the collision, brake support will
higher speeds. Braking is most effective at Descriptions of what happens in these three increase pressure.
speeds above 70 km/h (43 mph) and less effec- steps are provided below.
tive at lower speeds. 1 - Collision warning
City Safety sub-functions The driver is first alerted to the risk of an immi-
nent collision.
City Safety can detect pedestrians, cyclists or
vehicles that are stationary, are moving in the
same direction as your vehicle and are ahead of
your vehicle. City Safety can also detect pedes-
trians, cyclists or large animals that are crossing
the road in front of your vehicle.
If there is a risk of a collision with a pedestrian,
large animal, cyclist or another vehicle, or with a
vehicle described in the section "City Safety in
crossing traffic", the driver will be alerted with
light, sound and pulsations in the brake pedal. At
Function overview76. lower speeds, during hard braking or if the accel-
Audio-visual collision warning erator pedal is pressed, the brake pedal pulsation
warning will not be given. The intensity of the
Camera/radar sensor distance monitoring brake pedal pulsations varies according to the
vehicle's speed.
76 Note: This illustration is general and details may vary depending on model. }}
335
DRIVER SUPPORT
|| 3 - Auto-brake When City Safety applies the brakes, a text mes- Setting a warning distance for City
The automatic braking function is activated at the sage will appear in the instrument panel to notify Safety
last moment. the driver that the function is/was activated. City Safety is always active, but the function's
If the driver has not taken evasive action by this warning distance can be adjusted.
stage and a collision is imminent, the automatic WARNING
braking function will be triggered. This occurs City Safety may not be used to change how NOTE
whether or not the driver is pressing the brake the driver operates the vehicle. The driver The City Safety function cannot be deacti-
pedal. Full braking force will be applied to reduce must not only rely on City Safety to brake the vated. It is activated automatically each time
the speed at impact or reduced braking effect will vehicle.
the engine/electric motor is started.
be applied if this is sufficient to avoid the colli-
sion. Related information
The alert distance determines the sensitivity of
The seat belt tensioners may be activated along • City Safety™ (p. 333)
the system and regulates the distance at which
with the automatic braking function. See "Seat the light, sound and brake pulsations will be acti-
belt tensioners" for more information. vated.
In certain situations, auto-braking may begin with To select warning distance:
a limited braking force before applying full brak-
ing force. 1. Select Settings My Car IntelliSafe in
the center display's Top view.
If City Safety has prevented a collision, the vehi-
cle will be kept at a standstill until the driver 2. Under City Safety Warning, tap Late,
takes action. If the vehicle has slowed to avoid Normal or Early to set the desired warning
colliding with a slower-moving vehicle ahead, your distance.
speed will be reduced to that vehicle's speed. If the driver feels that the Early setting is giving
Auto-braking can always be cancelled if the too many warnings or finds them irritating, the
driver presses hard on the accelerator pedal. Normal or Late warning distance settings can
be selected instead.
NOTE If the driver feels that the warnings are too fre-
When City Safety activates the brakes, the quent and distracting, the warning distance can
brake lights come on. be reduced. This will reduce the total number of
warnings, but it will also result in City Safety pro-
viding warnings at a later stage.
336
DRIVER SUPPORT
The Late warning distance setting should there- NOTE Detecting obstacles with City Safety
fore only be used in exceptional cases, such as City Safety can detect vehicles, cyclists, large
when a more dynamic driving style is preferred. The warning with direction indicators for Rear
animals and pedestrians.
Collision Warning is deactivated if the colli-
sion warning distance in the City Safety func- Vehicles
WARNING
tion is set to the lowest level "Late". City Safety detects most types of vehicles that
• No automatic system can guarantee
The seat belt tensioning and braking func- are either stationary, moving in the same direc-
100% correct function in all situations. tion as your vehicle or those described in "City
tions remain active.
You should therefore never test use of Safety in crossing traffic".
City Safety in the direction of people, ani-
mals or vehicles – this could lead to Related information For City Safety to be able to detect a vehicle in
severe damage, serious personal injury or • City Safety™ (p. 333) the dark, its headlights and taillights must be on
even death. and clearly visible.
• City Safety warns the driver if there is a Cyclists
risk of collision, but the function cannot
reduce the driver's reaction time.
• Even if the warning distance has been set
to Early, warnings may be perceived as
late in certain situations – e.g. when there
are large speed differences or if the vehi-
cle ahead suddenly brakes heavily.
• With the warning distance set to Early,
warnings come further in advance. This
may cause the warnings to come more
frequently than with warning distance
Normal, but is recommended since it can
make City Safety more effective. Optimal examples of what City Safety would interpret to
be a cyclist: clear body and bicycle shapes.
For optimal performance, the system's function
for cyclist detection needs the clearest possible
information about the contours of the bicycle and
of the cyclist's head, arm, shoulders, legs, torso
}}
337
DRIVER SUPPORT
338
DRIVER SUPPORT
}}
339
DRIVER SUPPORT
340
DRIVER SUPPORT
City Safety and delayed evasive However, if City Safety determines that an eva- NOTE
maneuvers sive maneuver would not be possible due to traf-
fic in the adjacent lane(s), the function can assist The function uses the vehicle's radar unit,
City Safety can assist the driver by automatically
the driver by automatically starting to apply the which has some general limitations – see the
braking the vehicle when it is not possible to
brakes at an earlier stage. section "Radar unit limitations".
avoid a collision by steering alone.
341
DRIVER SUPPORT
City Safety limitations Camera and radar sensor's field of vision Driver intervention
City Safety functionality may be reduced in cer- The camera's field of vision is limited and in cer- Backing up
tain situations. tain situations, it may be unable to detect pedes- City Safety is temporarily deactivated when the
trians, large animals, cyclists or vehicles, or it may vehicle is backing up.
Surroundings detect them later than expected.
Low speed
Low objects Vehicles that are dirty may be detected later than City Safety is not activated at very low speeds
Hanging objects, such as flags for overhanging clean vehicles, and in dark conditions, motorcy- under 4 km/h (3 mph). The system will therefore
loads or accessories such as auxiliary lights or cles may be detected late or not at all. not intervene in situations in which your vehicle is
front protective grids that extend beyond the
If a text message displayed in the instrument approaching another vehicle very slowly, such as
height of the hood, may limit City Safety function-
panel indicates that the camera/radar sensor is when parking.
ality.
obstructed, it may be difficult for City Safety to Active driver
Slippery road conditions detect pedestrians, large animals, cyclists, vehi- Action by the driver always has priority. City
The extended braking distance on slippery roads cles or lane markings in front of the vehicle. City Safety will therefore not react or will react at a
may reduce City Safety's capacity to help avoid a Safety functionality may therefore be reduced. later stage with a warning or intervention in situa-
collision. In these types of situations, the Anti-
Text messages may not be displayed for all situa- tions in which the driver is clearly steering and
lock Braking System and Electronic Stability Con-
tions in which the windshield sensors are operating the accelerator pedal, even if a collision
trol (ESC77) will help provide optimal braking is unavoidable.
blocked. The driver must therefore always keep
power with maintained stability.
the windshield in front of the camera/radar sen- An active and aware driving style may therefore
Backlighting sor clean. delay collision warnings and intervention in order
The visual warning signal in the windshield may
to minimize unnecessary warnings.
be difficult to detect in bright sunlight, if there are CAUTION
reflections, or if the driver is wearing sunglasses
or not looking straight ahead. Maintenance and replacement of City Safety
components may only be performed by a
Heat
workshop – an authorized Volvo workshop is
If the temperature in the passenger compartment recommended.
is high due to e.g. bright sunlight, the visual warn-
ing signal in the windshield may be temporarily
disabled.
342
DRIVER SUPPORT
Other limitations • Warnings and brake interventions for In the center display's Top view, tap:
pedestrians and cyclists are disengaged
at vehicle speeds over 80 km/h
• Settings My Car IntelliSafe
WARNING
(50 mph). Related information
• Warnings and brake interventions can be
triggered late or not at all if the traffic sit- • Do not place, affix or mount anything on • City Safety™ (p. 333)
the inside or outside of the windshield, or
uation or external influences prevent the
in front of or around the camera and
camera and radar unit from properly
radar unit – this could disrupt camera-
detecting pedestrians, cyclists, large ani-
based functions.
mals or vehicles ahead of the vehicle.
• To be able to detect vehicles at night, its • Objects, snow, ice or dirt in the area of
the camera sensor can reduce the func-
front and rear lights must work and illumi-
tion, disengage it completely or give an
nate clearly.
improper function response.
• The camera and radar unit have a limited
range for pedestrians and cyclists – the
system can provide effective warnings NOTE
and brake interventions if the relative The function uses the vehicle's camera unit,
speed is lower than 50 km/h (30 mph). which has some general limitations – see the
For stationary or slow-moving vehicles, section "Camera unit limitations".
warnings and brake interventions are
effective at vehicle speeds of up to
70 km/h (43 mph). Speed reduction for NOTE
large animals is less than 15 km/h
The function uses the vehicle's radar unit,
(9 mph) and can be achieved at vehicle
which has some general limitations – see the
speeds over 70 km/h (43 mph). At lower
section "Radar unit limitations".
speeds, the warning and brake interven-
tion for large animals is less effective.
Market limitations
• Warnings for stationary or slow-moving
City Safety is not available in all countries. If City
vehicles and large animals can be disen-
gaged due to darkness or poor visibility. Safety is not shown in the center display's
Settings menu, your vehicle is not equipped with
this function.
343
DRIVER SUPPORT
Related information
• City Safety™ (p. 333)
344
DRIVER SUPPORT
RCW is automatically activated each time the • the vehicle approaching from the rear is
engine is started. detected at a late stage
RCW can warn the driver of a potential collision • the vehicle approaching from the rear
with vehicles approaching from behind by rapidly changes lanes at a late stage
flashing the turn signals. • the vehicle approaching from the rear is mov-
ing at a speed above 80 km/h (50 mph)
If, at a speed below 30 km/h (20 mph), the RCW
function detects that the car is in danger of being • a trailer, bicycle holder or similar is con-
hit from behind, the seatbelt tensioners may ten- nected to the vehicle's electrical system - the
sion the front seatbelts and activate the Whiplash RCW function will then be automatically
Protection System safety system. deactivated.
Immediately before a collision from behind, RCW
may also activate the foot brake in order to NOTE
reduce the forward acceleration of the car during In certain markets RCW does not warn with
the collision. However, the brakes will only be the direction indicators due to local traffic
applied if your vehicle is stationary. The brakes regulations – in such cases, that part of the
will be immediately released if the accelerator function is deactivated.
pedal is depressed.
345
DRIVER SUPPORT
BLIS*
The BLIS78 function is designed to help provide
assistance in heavy traffic with several lanes
moving in the same direction by helping the
driver to detect the presence of vehicles in the
"blind spot" area behind and to the side of the
vehicle.
The BLIS button in the center display's Func- Rapidly approaching vehicle zone.
tion view is used to activate/deactivate the
The BLIS function is active at speeds
function.
above 10 km/h (6 mph).
The system is designed to react to:
• vehicles passing your vehicle
• vehicles that are rapidly approaching your
vehicle from behind.
When BLIS detects a vehicle in zone 1 or a rap-
idly approaching vehicle in zone 2, an indicator
light will illuminate in the relevant rearview mirror
and glow steadily. If the driver then uses the turn
signal on the side in which the warning has been
346 * Option/accessory.
DRIVER SUPPORT
given, the indicator light will become brighter and • Recommended maintenance for BLIS Activating/deactivating BLIS
begin flashing. (p. 349) The BLIS80 function can be activated/deacti-
• BLIS messages (p. 350) vated.
NOTE
The light illuminates on the side of the vehicle
where the system has detected the vehicle. If
the vehicle is passed on both sides simulta-
neously, both lights come on.
WARNING
• The BLIS function is supplementary driver
support intended to facilitate driving and
help make it safer – it cannot handle all
situations in all traffic, weather and road
conditions.
Location of BLIS indicator light.81
• The responsibility for changing lanes
Indicator light
safely and using good judgment always
rests with the driver. The BLIS button in the center display's Func-
• BLIS is not a substitute for the driver's tion view is used to activate/deactivate the
attention and judgment. The driver is function.
always responsible for ensuring the vehi- – Tap the BLIS button in Function view.
cle is driven in a safe manner, at the > The BLIS indicator light shows the status
appropriate speed, with an appropriate of the function: GREEN (on) or GRAY
distance to other vehicles, and in accord- (off).
ance with current traffic rules and regula-
tions. If BLIS is activated when the engine is started,
the indicator lights in the rearview mirrors will
flash once.
Related information
• Activating/deactivating BLIS (p. 347) If BLIS is deactivated when the engine is turned
off, it will remain off the next time the engine is
• BLIS limitations (p. 348)
started and the indicator lights will not illuminate. }}
347
DRIVER SUPPORT
Related information
• BLIS* (p. 346)
Keep this area clean (on both the left and right sides of
the vehicle)83.
Examples of limitations:
• Dirt, ice and snow covering the sensors may
reduce functionality and prevent the system
from providing warnings.
• The BLIS function is automatically deacti-
vated if a trailer, bicycle holder or similar is
connected to the vehicle's electrical system.
• For BLIS to function optimally, bicycle hold-
ers, luggage racks or similar should not be
mounted on the vehicle's towbar.
348 * Option/accessory.
DRIVER SUPPORT
84 Note: This illustration is general and details may vary depending on model.
* Option/accessory. 349
DRIVER SUPPORT
BLIS messages
A number of messages related to BLIS85 may
be displayed in the instrument panel.
Some examples of symbols and messages are shown in the table below.
Message Meaning
Blind spot sensor The system is not functioning as intended. Contact a workshop ‒ an authorized Volvo workshop is recommended.
Service required
Blind spot system off BLIS and CTA have been deactivated because a trailer has been connected to the vehicle's electrical system.
Trailer attached
Related information
• BLIS* (p. 346)
350 * Option/accessory.
DRIVER SUPPORT
* Option/accessory. 351
DRIVER SUPPORT
352 * Option/accessory.
DRIVER SUPPORT
Related information
• Cross Traffic Alert* (p. 351)
Keep this area clean (on both the left and right sides of
the vehicle)92.
The CTA sensors are located on the inside of
each of the rear fenders/bumpers and are also
used by the BLIS93 and Rear Collision Warning
functions.
92 Note: This illustration is general and details may vary depending on model.
93 Blind Spot Information
* Option/accessory. 353
DRIVER SUPPORT
Related information
• Cross Traffic Alert* (p. 351)
354 * Option/accessory.
DRIVER SUPPORT
Road Sign Information* WARNING • Road Sign Information with speed camera
The Road Sign Information (RSI95)
function noti- information (p. 359)
• The Road Sign Information function is
fies the driver of speed-related road signs the supplementary driver support intended to • Road Sign Information limitations (p. 359)
vehicle is passing. facilitate driving and help make it safer –
it cannot handle all situations in all traffic,
weather and road conditions.
• Road Sign Information is not a substitute
for the driver's attention and judgment.
The driver is always responsible for
ensuring the vehicle is driven in a safe
manner, at the appropriate speed, with an
appropriate distance to other vehicles,
and in accordance with current traffic
rules and regulations.
Related information
Examples of signs that can be detected96. • Activating/deactivating Road Sign Informa-
If the vehicle passes a speed limit sign, it will be tion (p. 356)
displayed in the instrument panel and the head- • Road Sign Information and sign displays
up display*. (p. 356)
• Road Sign Information and Sensus
NOTE Navigation (p. 357)
In certain markets, the Road Sign Information • Road Sign Information with Speed Warning
function (RSI) is only available in combination and Settings (p. 357)
with Sensus Navigation.
• Activating/deactivating Speed Warning in
Road Sign Information (p. 358)
* Option/accessory. 355
DRIVER SUPPORT
356 * Option/accessory.
DRIVER SUPPORT
Signs for "School" and "Children Road Sign Information and Sensus Road Sign Information with Speed
playing" Navigation Warning and Settings
If the warning sign98 "School" If the vehicle is equipped with Sensus Navigation, The Speed Limit Warning sub-function for
or "Children playing" is speed-related information will be provided in the RSI100 can be switched On or Off.
included in the satellite naviga- following situations: Speed Limit Warning alerts the driver if the
tor's map data99, a symbol of vehicle's speed has exceeded the applicable
• In cases where the speed limit is given indi-
this type will be displayed in the rectly, e.g. signs for highways or other major speed limit or the preset Speed Limiter speed.
instrument panel. roads. The warning will be repeated once if the driver
does not slow down.
Related information • If a previously detected speed sign is
When Speed Warning is acti-
• Road Sign Information* (p. 355) deemed to be no longer valid and no new
sign has been passed. vated, the symbol for the cur-
rent speed limit in the instru-
NOTE ment panel101 will flash tempo-
rarily if that speed is exceeded.
In certain markets, the Road Sign Information
function (RSI) is only available in combination
with Sensus Navigation. The driver can be alerted if the
vehicle is exceeding a detected
speed limit and is approaching
NOTE a speed camera.
If a downloaded third-party app is used for
navigation, there is no support for speed-rela-
ted information.
Related information
• Road Sign Information* (p. 355)
98 Road signs differ according to market ‒ the illustrations shown here are just examples.
99 Only vehicles with Sensus Navigation.
100Road Sign Information
101Road signs differ according to market ‒ the illustration shown here is just an example. }}
* Option/accessory. 357
DRIVER SUPPORT
358 * Option/accessory.
DRIVER SUPPORT
Road Sign Information with speed For more information on Speed Warnings in con- Road Sign Information limitations
camera information junction with speed cameras, see "Road Sign Road Sign Information (RSI104) functionality may
Vehicles equipped with RSI102 and Sensus Information with Speed Warning and settings" be reduced in certain situations.
Navigation* can provide information on upcom- and "Road Sign Information limitations".
ing speed cameras in the instrument panel. RSI could have reduced functionality due to e.g.:
NOTE • faded road signs
• For an audible alert to be provided if the • signs located in a curve in the road
speed is exceeded, the Speed Limit
• twisted or damaged signs
Warning function must be activated and
the Road Sign Audio Warning sub- • signs positioned high above the road
function must be On. Audible alerts are • fully/partially obstructed or poorly positioned
provided if the vehicle's speed exceeds signs
the speed displayed by RSI in the instru-
ment panel.
• Information about speed cameras on the
navigation map is not available for all
markets/areas.
Speed camera information in the instrument panel103.
If the vehicle exceeds a Related information
detected speed limit with the
Speed Warning function acti-
• Road Sign Information* (p. 355)
vated, the driver is given a • Road Sign Information with Speed Warning
speed warning when the vehi- and Settings (p. 357)
cle is approaching a speed • Road Sign Information limitations (p. 359)
camera if the navigation map
for the vehicle's current location contains infor-
mation on speed cameras.
* Option/accessory. 359
DRIVER SUPPORT
360 * Option/accessory.
DRIVER SUPPORT
The warnings will be repeated after a short time if WARNING Activating/deactivating Driver Alert
driving behavior does not improve. Control
An alarm from Driver Alert Control should be
taken very seriously since a sleepy driver is The Driver Alert Control (DAC) function can be
WARNING often not aware of their own condition. activated/deactivated.
• The Driver Alert Control function is sup- If the alarm sounds or you feel fatigued: On/Off
plementary driver support intended to
facilitate driving and help make it safer – • Stop the vehicle safely as soon as possi- To change DAC settings:
ble and rest. 1. Tap Settings in the center display's Top
it cannot handle all situations in all traffic,
weather and road conditions. Studies have shown that it is just as danger- view.
ous to drive while tired as it is to drive under
• Driver Alert Control must not be used to the influence of alcohol or other stimulants. 2. Select My Car IntelliSafe Driver Alert
extend a period of driving. The driver Control.
should plan in breaks at regular intervals
and make sure they are well rested. Related information 3. Select/deselect Alertness Warning to acti-
• Activating/deactivating Driver Alert Control vate/deactivate DAC.
• Driver Alert Control is not a substitute for (p. 361)
the driver's attention and judgment. The Related information
driver is always responsible for ensuring • Selecting guidance to a rest area if the
• Driver Alert Control (p. 360)
the vehicle is driven in a safe manner, at Driver Alert Control warning has been given
the appropriate speed, with an appropri- (p. 362)
ate distance to other vehicles, and in • Driver Alert Control limitations (p. 362)
accordance with current traffic rules and
regulations.
361
DRIVER SUPPORT
Selecting guidance to a rest area if Driver Alert Control limitations Lane Keeping Aid
the Driver Alert Control warning has Driver Alert Control (DAC) functionality may be Lane Keeping Aid (LKA107) is designed to
been given reduced in certain situations. actively steer the vehicle on freeways, highways
The Rest Stop Guidance function can be and other major roads to help the driver reduce
In certain situations, the system may provide a the risk of the vehicle unintentionally veering out
switched on or off.
warning even if it has not detected a change in
When the guide is activated, it will automatically of the lane.
driving behavior, e.g.:
display suggestions for a suitable place to take a
Lake Keeping Assistance steers the vehicle back
break if the DAC warning is given. • in strong crosswinds
into the lane and/or alerts the driver using vibra-
To select Rest Stop Guidance: • on grooved road surfaces. tions in the steering wheel.
1. Tap Settings in the center display's Top Lane Keeping Aid is active at speeds between
view. WARNING
65-200 km/h (40-125 mph) on roads with
In certain cases, driving behavior might not be clearly visible traffic lane marker lines.
2. Select My Car IntelliSafe Driver Alert affected despite the driver's fatigue – when
Control. using the Pilot Assist function – resulting in On narrow roads, the function may be unavailable
the driver not getting a warning from DAC. and go into standby mode. The function will
3. Select/deselect Rest Stop Guidance to
It is therefore very important to always stop become available again when the road becomes
activate/deactivate the function.
and take a break at the slightest sign of fati- sufficiently wide.
Related information gue, regardless of whether the DAC function
• Driver Alert Control (p. 360) has issued a warning or not.
NOTE
The function uses the vehicle's camera unit,
which has some general limitations – see the
section "Camera unit limitations".
Related information
• Driver Alert Control (p. 360)
362
DRIVER SUPPORT
108The steering wheel vibrations vary. The more time the vehicle is over the lane marker line, the longer the vibrations.
109See "LKA assistance options" under "Activating/deactivating Lane Keeping Aid".
}}
363
DRIVER SUPPORT
|| Lane Keeping Aid does not intervene • Lane Keeping Aid symbols in the instrument Steering assistance with Lane
panel (p. 369) Keeping Aid
The LKA110 steering assistance function only
functions if the driver's hands are on the steering
wheel, which the system continuously monitors.
If the driver does not keep
his/her hands on the steering
wheel, the driver display shows
this symbol combined with a
message, which prompts the
driver to actively steer the car:
364
DRIVER SUPPORT
Activating/deactivating Lane Selecting type of assistance for Lane Keeping Aid limitations
Keeping Aid Lane Keeping Aid In certain demanding driving conditions, Lane
The Lane Keeping Aid (LKA111) function can be The driver can determine what types of assis- Keeping Aid may not be able to properly assist
switched On or Off. tance LKA112 should provide if the vehicle veers the driver. In these situations, it is recommended
from its lane. that the function be deactivated.
On/Off 1. Select Settings My Car IntelliSafe in Examples of such situations include:
Press the Lane Keeping Aid
button in the center display's
the center display's Top view. • road work
Function view. 2. Under Lane Keeping Aid Mode, select • winter driving conditions
what assistance LKA should provide: • poor road surfaces
• Assist the driver will receive steering • a very sporty driving style
assistance but no warning.
• bad weather with reduced visibility
• GREEN button indicator light - LKA is acti- • Both - the driver will receive both steering • roads with indistinct or no lane markings
vated. assistance and a warning.
• sharp edges or lines other than the lane's
• GRAY button indicator light - LKA is deacti- • Warning - the driver will only receive a side markings
vated. warning.
• when the power steering works at reduced
Related information Related information power - e.g. during cooling due to overheat-
• Lane Keeping Aid (p. 362) • Lane Keeping Aid (p. 362) ing (see section "Speed-dependent steering
force").
NOTE
The function uses the vehicle's camera unit,
which has some general limitations – see the
section "Camera unit limitations".
365
DRIVER SUPPORT
|| Related information
• Lane Keeping Aid (p. 362)
• Speed-dependent steering wheel resistance
(p. 270)
366
DRIVER SUPPORT
Windscreen sensor The camera's ability to detect the lane in front of the vehicle is reduced.
Sensor blocked, see Owner's manual
Lane Keeping Aid LKA's steering assistance is disabled when the driver's hands are not on the wheel. Follow
the instructions and steer the vehicle.
Apply steering
Lane Keeping Aid LKA will go into standby mode until the driver begins steering the vehicle again.
Standby until steering applied
367
DRIVER SUPPORT
Related information
• Lane Keeping Aid (p. 362)
368
DRIVER SUPPORT
369
DRIVER SUPPORT
• Collision avoidance assistance – • Limitations of steering assistance during col- • Steering assistance during collision risks
lision risks from oncoming traffic (p. 374) from behind*
Automatic intervention
• Steering assistance during collision risks Although it is possible to deactivate the func-
from behind* (p. 375) tion, the driver is advised to keep it activated
NOTE
since it can help improve driving safety in
It is always the driver who must decide how • Activating/deactivating Steering assistance
most cases.
much the vehicle should be in control – the during collision risks from behind* (p. 376)
vehicle can never take command. • Limitations of steering assistance during col-
Related information
lision risks from behind (p. 376)
• Steering assistance at risk of collision
(p. 370)
370 * Option/accessory.
DRIVER SUPPORT
}}
371
DRIVER SUPPORT
372 * Option/accessory.
DRIVER SUPPORT
NOTE Steering assistance during collision However, the function will not provide steering
risks from oncoming traffic assistance if the turn signal is used. The function
The function uses the vehicle's radar unit, will also not be activated if it detects that the
This sub-function can help assist a distracted
which has some general limitations – see the driver is actively operating the vehicle.
driver who has not noticed that the vehicle is
section "Radar unit limitations".
veering into oncoming traffic. After the system has automatically intervened,
this text message will appear in the instrument
Related information panel:
• Steering assistance at risk of collision
(p. 370) • Collision avoidance assistance –
Automatic intervention
• Speed-dependent steering wheel resistance
(p. 270)
WARNING
• The "Steering assistance at risk of head-
on collision" subfunction is supplemen-
tary driver support intended to improve
driving safety – it cannot handle all situa-
tions in all traffic, weather and road condi-
tions.
The function provides assistance by swerving your vehi-
cle back into your own lane. • Pilot Assist is only activated if there is a
Oncoming vehicles high risk of collision – you must therefore
never wait for the function to intervene.
Own vehicle • The function is not a substitute for the
The function is active at speeds between driver's attention and judgment. The driver
60-140 km/h (37-87 mph) on roads with clearly is always responsible for ensuring the
visible traffic lane markings/lines. vehicle is driven in a safe manner, at the
appropriate speed, with an appropriate
If your vehicle is starting to veer from your own distance to other vehicles, and in accord-
lane and a vehicle is approaching from the oppo- ance with current traffic rules and regula-
site direction, this function can help the driver tions.
steer the vehicle back into its own lane.
}}
373
DRIVER SUPPORT
2. Deselect Collision avoidance assistance. • if more than half of your vehicle has moved
into the adjacent lane
> The function will be deactivated.
• outside the speed range 60-140 km/h
(37-87 mph)
NOTE • when the power steering works at reduced
When the Collision avoidance assistance power - e.g. during cooling due to overheat-
function is deactivated, all subfunctions of the ing (see section "Speed-dependent steering
following are deactivated: force").
• Steering assistance at risk of run-off Functionality may also be reduced in other situa-
• Steering assistance at risk of head-on tions, such as:
collision • road work
• Steering assistance during collision risks • winter driving conditions
from behind*
• narrow roads
Although it is possible to deactivate the func-
tion, the driver is advised to keep it activated • poor road surfaces
since it can help improve driving safety in • a very sporty driving style
most cases. • bad weather with reduced visibility.
In these demanding driving conditions, the func-
Related information tion may not be able to properly assist the driver.
• Steering assistance at risk of collision In these situations, it is recommended that it is
(p. 370) turned off.
374 * Option/accessory.
DRIVER SUPPORT
NOTE Steering assistance during collision cle approaching, the function can provide assis-
risks from behind* tance.
The function uses the vehicle's camera unit,
If you become distracted and do not notice your The function is active at speeds between
which has some general limitations – see the
vehicle starting to veer out of the lane while 60-140 km/h (37-87 mph) on roads with clearly
section "Camera unit limitations".
another vehicle is approaching from behind or is visible traffic lane markings/lines.
in your vehicle's blind spot, this sub-function can
After the system has automatically intervened,
NOTE help provide assistance.
this text message will appear in the instrument
The function uses the vehicle's radar unit, panel:
which has some general limitations – see the
section "Radar unit limitations".
• Collision avoidance assistance –
Automatic intervention
* Option/accessory. 375
DRIVER SUPPORT
376 * Option/accessory.
DRIVER SUPPORT
NOTE
The function uses the vehicle's camera unit,
which has some general limitations – see the
section "Camera unit limitations".
NOTE
The function uses the vehicle's radar unit,
which has some general limitations – see the
section "Radar unit limitations".
Related information
• Steering assistance at risk of collision
(p. 370)
• Speed-dependent steering wheel resistance
(p. 270)
377
DRIVER SUPPORT
Windscreen sensor The camera's ability to detect the lane in front of the vehicle is reduced.
Sensor blocked, see Owner's manual
Related information
• Steering assistance at risk of collision
(p. 370)
378
DRIVER SUPPORT
Park Assist* moving but will cease after the vehicle has been WARNING
The Park Assist function can help the driver stationary for approx. 2 seconds. Audible signals
when maneuvering in tight spaces by indicating for obstacles behind the vehicle will remain active • The Parking Assist function is supple-
even when the vehicle is stationary. mentary driver support intended to facili-
distances to obstacles using audible signals and
tate driving and help make it safer – it
graphics in the center display. If a detected obstacle is within 30 cm (1 ft) from cannot handle all situations in all traffic,
the front or rear of the vehicle, the tone will weather and road conditions.
become constant and the active sensor's field
closest to the vehicle symbol will be filled in. • The parking sensors have dead/blind
spots where objects cannot be detected.
The volume of the Park Assist audible signals
can be adjusted while the signal is being given • Pay particular attention to people and
animals near the vehicle.
using the >II knob or in the center display's Top
view under Settings. • Parking Assist is not a substitute for the
driver's attention and judgment. The driver
is always responsible for ensuring the
NOTE
vehicle is driven in a safe manner, at the
• Acoustic warnings are only given for appropriate speed, with an appropriate
objects directly in front of the vehicle's distance to other vehicles, and in accord-
path. ance with current traffic rules and regula-
Display view showing obstacle zones and sensor sec-
tors. tions.
The center display shows an overview of the vehi-
cle in relation to objects that have been detected. Related information
• Park Assist front, rear and sides (p. 380)
The marked sector indicates where the obstacle
is located. The closer the vehicle symbol is to a • Activating/deactivating Park Assist (p. 381)
marked sector, the closer the detected obstacle • Park Assist limitations (p. 381)
is to your vehicle. • Recommended maintenance for Park Assist
The audible signals will also speed up the closer (p. 382)
the obstacle is to the vehicle. The volume of the • Park Assist symbols and messages (p. 383)
audio system will be automatically lowered.
Audible signals for obstacles in front and to the
sides of the vehicle are active when the vehicle is
* Option/accessory. 379
DRIVER SUPPORT
Side sensors
380
DRIVER SUPPORT
Related information
• Park Assist* (p. 379)
}}
* Option/accessory. 381
DRIVER SUPPORT
CAUTION NOTE
In some circumstances, the Park Assist Sys- Dirt, ice and snow covering the sensors could
tem may produce false warnings due to exter- cause false warnings, reduced function, or no
nal sound sources with the same ultrasonic function.
frequencies as those the system works with.
Examples of such sources are horns, wet tires Related information
on asphalt, pneumatic brakes, exhaust noise
• Park Assist* (p. 379)
from motorcycles, etc.
115Note: This illustration is general and details may vary depending on model.
382 * Option/accessory.
DRIVER SUPPORT
Park Assist System One or more of the sensors are blocked. Check and clean/remove the obstacle as soon as pos-
sible.
Sensors blocked, cleaning nee-
ded
Park Assist System The system is not functioning as intended. Contact a workshop ‒ an authorized Volvo workshop
is recommended.
Unavailable Service required
Related information
• Park Assist* (p. 379)
* Option/accessory. 383
DRIVER SUPPORT
384 * Option/accessory.
DRIVER SUPPORT
119Note: This illustration is general and details may vary depending on model.
120Note: This illustration is general and details may vary depending on model. }}
* Option/accessory. 385
DRIVER SUPPORT
|| Side cameras Park Assist Camera trajectory lines help simplify parallel parking, backing into tight
The Park Assist Camera uses trajectory lines spaces or attaching a trailer.
and fields on the screen to indicate the vehicle's The lines on the screen are projected as if they
position in relation to its immediate surround- were painted lines on the ground behind the
ings. vehicle and are directly affected by the way in
which the steering wheel is turned. This enables
the driver to see path the vehicle will take, even if
he/she turns the steering wheel.
These lines also indicate the outermost limits that
any object (towbar, rearview mirrors, corners of
the body, etc.) extends out from the vehicle.
120Note: This illustration is general and details may vary depending on model.
121The illustration is generic - details may vary according to vehicle model.
386 * Option/accessory.
DRIVER SUPPORT
* Option/accessory. 387
DRIVER SUPPORT
|| 1. Tap Towbar (1). Sensor field from Park Assist for The front and rear fields change colors (from yel-
> The trajectory line for the towbar's antici- Park Assist Camera low to orange to red) as the vehicle moves closer
pated path toward the vehicle will appear If the vehicle is equipped with Park Assist, dis- to an obstacle.
and the vehicle's trajectory lines will dis- tances will be shown in the 360° view with col- Front and rear field Distance in meters
appear. ored fields for each sensor that has detected an colors (feet)
Trajectory lines cannot be displayed for obstacle.
Yellow 0.6-1.5 (2.0-4.9)
both the vehicle and the towbar at the Front and rear sensors
same time. Orange 0.4-0.6 (1.3-2.0)
2. Tap Zoom (2) for a close-up view for more Red 0-0.4 (0-1.3)
precise maneuvering.
> The camera will zoom in. Side sensor fields
The side sensor fields will only be shown in
Related information orange.
• Park Assist Camera* (p. 384)
Side field color Distance in meters (feet)
Orange 0-0.3 (0-1.0)
Related information
• Park Assist Camera* (p. 384)
388 * Option/accessory.
DRIVER SUPPORT
Starting the Park Assist Camera Other camera views switch off at 15 km/h Park Assist Camera limitations
The Park Assist Camera starts automatically (9 mph) and are not reactivated. The Park Assist Camera may not be able to
when reverse gear is engaged or can be started detect all conditions in all situations and func-
Related information
manually using one of the center display's func- tionality may therefore be limited.
tion buttons. • Park Assist Camera* (p. 384)
The driver should be aware of the following limi-
Camera view when backing up tations for the Park Assist Camera:
When reverse gear is engaged, the screen shows
the rear view123. WARNING
Camera view when manually starting Be extra cautious when
reversing if this symbol is
the camera shown when a trailer, bike
Start the Park Assist Camera carrier or similar is attached
using this button in the center and electrically connected
display's Function view. to the vehicle.
The screen will first show the The symbol indicates that
most recently used camera the rear parking assist sensors are deacti-
view. However, each time the vated and will not warn of any obstacles.
engine is started, the previous side view will be
replaced by the 360° view and a previously dis- NOTE
played zoomed-in rear view will be replaced by
the regular rear view. A bike carrier and other accessories mounted
on the rear of the vehicle can obscure the
Automatically deactivating the camera camera's view.
Front view switches off when the vehicle's speed
reaches 25 km/h (16 mph) to help avoid dis-
tracting the driver. It will be automatically reactiva-
ted if the vehicle's speed falls below 22 km/h
(14 mph) within 1 minute as long as the vehicle's
speed has not exceeded 50 km/h (31 mph).
* Option/accessory. 389
DRIVER SUPPORT
|| Blind sectors Defective camera means that the brightness and quality of the
If a camera sector is dark and image may vary slightly. Poor lighting conditions
contains this symbol, this indi- may result in reduced image quality.
cates that the camera is not
functioning properly. Related information
• Park Assist Camera* (p. 384)
See the following illustration for
an example.
Lighting conditions
The camera image is automatically adjusted
according to the current lighting conditions. This
390 * Option/accessory.
DRIVER SUPPORT
NOTE
Keep the camera lens free of dirt, snow and
ice to help ensure the best functionality. This
is particularly important in poor light condi-
tions.
Related information
• Park Assist Camera* (p. 384)
* Option/accessory. 391
DRIVER SUPPORT
Park Assist System One or more of the sensors are blocked. Check and clean/remove the obstacle as soon as possible.
Sensors blocked, cleaning
needed
Park Assist System The system is not functioning as intended. Contact a workshop ‒ an authorized Volvo workshop is
recommended.
Unavailable Service required
A text message can be erased by briefly pressing If the message persists: Contact a workshop ‒ an Related information
the button in the center of the right-side authorized Volvo workshop is recommended. • Park Assist Camera* (p. 384)
steering wheel keypad.
392 * Option/accessory.
DRIVER SUPPORT
* Option/accessory. 393
DRIVER SUPPORT
NOTE
The PAP function measures the space and
steers the vehicle – the driver's role is to:
• keep close watch of the area around the
vehicle
• follow the instructions on the center dis-
play
Overview of parallel parking. Perpendicular parking overview.
• change gears (reverse/forward) – a
The PAP function parks the vehicle using the fol- The PAP function parks the vehicle using the fol- "ping" sound indicates when the driver
lowing steps: lowing steps: should change gears
1. The system searches for and measures 1. The system searches for and measures • regulate and maintain a safe speed
potential parking spaces. potential parking spaces.
• apply the brakes and stop.
2. The vehicle is steered while it is backing into 2. The vehicle is steered while it is backing into
the parking space. the space and its position is adjusted by driv- Information about the actions required by the
3. The vehicle's position in the space is ing forward/backward. driver are provided in the center display using
adjusted by driving forward/backward. symbols, graphics and/or text.
The Park Out function can be used to receive NOTE
PAP can be activated if the following criteria have
assistance from PAP while pulling out of a park- The PAP function Park Out cannot help the been met after the engine is started:
ing space. See the heading "Pulling out of a vehicle leave a perpendicular parking space –
parking space" under "Parking with Park Assist the function should only be used for parallel • No trailer is hitched to the vehicle
Pilot". parking. • Your vehicle's speed is lower than 30 km/h
(20 mph).
Related information
• Park Assist Pilot* (p. 393)
394 * Option/accessory.
DRIVER SUPPORT
NOTE To do so:
The distance between the vehicle and parking 1. The vehicle's speed may not exceed
spots should be 0.5-1.5 meters (1.6-5.0 ft) 30 km/h (20 mph) when parallel parking or
when PAP is looking for parking. 20 km/h (12 mph) when perpendicular park-
ing.
395
DRIVER SUPPORT
|| Backing into a parking space 2. Back up slowly and carefully without touch- Positioning the vehicle in the parking space
ing the steering wheel and do not exceed a
speed of 7 km/h (4 mph).
3. Be prepared to stop the vehicle when
instructed to do so by a graphic and mes-
sage in the center display.
NOTE
• Keep your hands away from the steering
wheel when the PAP function is acti-
vated.
• Make sure that the steering wheel is not
Parallel. hindered in any way and can rotate freely. Parallel.
Perpendicular. Perpendicular.
To back into a parking space: To do so:
1. Make sure the path behind your vehicle is 1. Move the gear selector to D, wait until the
clear and engage reverse gear. steering wheel turns and then drive slowly
forward.
396
DRIVER SUPPORT
2. Be prepared to stop the vehicle when Leaving a parking space with Park may need to turn the steering wheel back to the
instructed to do so by a graphic and mes- Assist Pilot maximum position in order to pull out of the park-
sage in the center display. The function Park Out can also help the driver ing space.
3. Engage reverse gear and back up slowly. to leave a parking space. If PAP determines that the driver can pull out of
NOTE the parking space without any extra maneuvers,
4. Be prepared to stop the vehicle when
the function will be deactivated, even if it seems
instructed to do so by a graphic and mes- Leaving a parking space with the Park Out as though the vehicle is not completely out of the
sage in the center display. function should only be used in connection parking space.
The function will switch off automatically and a with parallel parking – it does not work for
graphic and message will appear to indicate that perpendicular parking. Related information
parking has been completed. Adjustments can • Park Assist Pilot* (p. 393)
always be made be the driver afterward. Only the The Park Out function is acti-
driver can determine when the vehicle is correctly vated in the center display's
parked. Function view or in Camera
view.
CAUTION
The warning distance is shorter when the
sensors are used by PAP compared to when To do so:
they are used by the Parking Assist system.
1. Tap Park Out in Function view or in Camera
view.
Related information
2. Move the gear selector to the suitable posi-
• Park Assist Pilot* (p. 393)
tion (e.g. D or R) for the direction in which
you will be pulling out of the parking space.
3. Be prepared to stop the vehicle when
instructed to do so by a graphic and mes-
sage in the center display. Follow the instruc-
tions in the same way as for the parking pro-
cedure.
Note that the steering wheel can "spring" back
when the procedure is completed and the driver
* Option/accessory. 397
DRIVER SUPPORT
398 * Option/accessory.
DRIVER SUPPORT
128"Approved tires" refers to tires of the same type and make as the vehicle's original, factory-installed tires.
* Option/accessory. 399
DRIVER SUPPORT
NOTE
Dirt, ice and snow covering the sensors could
cause false warnings, reduced function, or no
function.
Related information
• Park Assist Pilot* (p. 393)
400 * Option/accessory.
DRIVER SUPPORT
Related information
• Park Assist Pilot* (p. 393)
* Option/accessory. 401
STARTING AND DRIVING
STARTING AND DRIVING
Starting the vehicle The remote key is not physically used to start the WARNING
The vehicle can be started using the start knob ignition because the vehicle is equipped with the
in the tunnel console when the remote key is in keyless Passive Start system. • Never use more than one inlay mat at a
time on the driver's floor. If any other type
the passenger compartment. To start the vehicle: of floor mat is used, remove the original
1. The remote key must be inside the vehicle. mat from the driver's seat floor before
For vehicles with Passive Start, the key must driving. All types of mats must be securely
be in the front section of the passenger anchored in the attachment points in the
compartment. With the optional keyless lock- floor. Make sure the floor mat does not
ing/unlocking function*, the key can be any- impede the movement of the brake pedal
where in the vehicle. or accelerator pedal in any way, as this
could be a serious safety hazard.
2. Press and hold down the brake pedal1 as far
as possible. • Volvo's floor mats are specially manufac-
tured for your vehicle. They must be prop-
3. Turn the start knob clockwise and release. erly secured in the attachment points in
The control will automatically return to the the floor to help ensure they cannot slide
original position. and become trapped under the pedals.
Start knob in the tunnel console.
The starter motor will crank until the engine
WARNING starts or until its overheating protection is trig-
Before starting: gered.
1 If the vehicle is moving, it is only necessary to turn the start knob clockwise to start the engine.
404 * Option/accessory.
STARTING AND DRIVING
WARNING NOTE
Never remove the remote control key from With a cold start, idling speed may be consid-
the vehicle while driving or the vehicle is erably higher than normal for certain engine
being towed. types. This is done to get the emissions sys-
tem up to normal operating temperature as
WARNING quickly as possible, which minimizes exhaust
emissions and protects the environment.
• Always remove the remote key from the
passenger compartment when you leave
Location of the backup reader in the tunnel console. the vehicle and make sure the ignition is CAUTION
If the Vehicle key not found message is shown in mode 0.
• When starting in cold weather, the auto-
in the instrument panel at start, place the remote • Always put the gear selector in P and matic transmission may shift up at slightly
key at the backup reader and then make a new apply the parking brake before leaving higher engine speeds than normal until
start attempt. the vehicle. Never leave the vehicle unsu- the automatic transmission fluid reaches
pervised while the engine is running. normal operating temperature.
NOTE
• Always open the garage door fully and • Do not race a cold engine immediately
When the remote key is placed in the backup make sure that ventilation is very good after starting. This could prevent fluids
reader, make sure that no other vehicle keys, before starting the engine in a garage. from properly lubricating vital compo-
metal objects or electronic devices (e.g. cellu- The exhaust fumes produced by the vehi- nents in the engine before it has reached
lar phones, tablets, laptops or chargers) are in cle contain carbon monoxide, which is the proper operating temperature.
the backup reader. Multiple vehicle keys close invisible and odorless but very toxic.
to each other in the backup reader can dis- • The engine should be idling when the
rupt their functionality. gear selector is moved. Never accelerate
WARNING until the gear is fully engaged. Accelerat-
ing rapidly before a gear is properly
CAUTION Always take along the remote control key engaged could lead to harder wear of
when leaving the vehicle and make sure that
components.
If the engine has not responded after 3 the vehicle electrical system is in ignition
attempts – wait for 3 minutes before starting mode 0 – especially if there are children in • To help prevent the transmission oil from
a new attempt. Starting capability increases if the vehicle. overheating, select P or N when idling at
the starter battery is given time to recover. a standstill for prolonged periods of time.
}}
405
STARTING AND DRIVING
|| Related information Switching off the vehicle • Selecting ignition mode (p. 408)
• Switching off the vehicle (p. 406) The vehicle can be switched off using the start
• Ignition modes (p. 407) knob in the tunnel console.
• Adjusting the steering wheel (p. 203)
• Jump starting using another battery (p. 447)
• Selecting ignition mode (p. 408)
Related information
• Starting the vehicle (p. 404)
• Ignition modes (p. 407)
• Adjusting the steering wheel (p. 203)
• Jump starting using another battery (p. 447)
406
STARTING AND DRIVING
* Option/accessory. 407
STARTING AND DRIVING
Selecting ignition mode • Ignition mode I - Turn the start knob clock- Brake functions
The vehicle's ignition can be put in various wise and release it. The control will automati- The vehicle's brakes are used to reduce speed
modes (levels) to make different functions availa- cally return to the original position. or prevent the vehicle from rolling.
ble. • Ignition mode II - Turn the start knob clock-
In addition to the wheel brakes and parking
wise and hold it there for approx. 5 seconds.
Selecting an ignition mode Release the knob, which will automatically brakes, the vehicle is also equipped with a num-
return to its original position. ber of automatic brake assist functions. These
systems help the driver by e.g. keeping the vehi-
• Back to ignition mode 0 - To return to igni- cle stationary when the brake pedal is not
tion mode 0 from mode I and II, turn the start depressed (e.g. at a traffic light or intersection),
knob clockwise and release it. The control when starting up a hill or when driving down a hill.
will automatically return to the original posi-
tion. Depending on how the vehicle is equipped, the
following brake assist functions may be included:
Related information
• Auto-hold brakes (Auto Hold)
• Starting the vehicle (p. 404)
• Hill Start Assist (Hill Start Assist)
• Switching off the vehicle (p. 406)
• Braking assist after a collision
• Ignition modes (p. 407)
• City Safety
Start knob in the tunnel console. • Adjusting the steering wheel (p. 203)
• Hill Descent Control (Hill Descent Control)*
• Ignition mode 0 - Unlock the vehicle and • Jump starting using another battery (p. 447)
keep the remote key in the passenger com- Related information
partment. • Brakes (p. 409)
• Parking brake (p. 411)
NOTE
• Auto-hold brakes (p. 415)
To set level I or II without engine start – do
not depress the brake pedal (or clutch pedal • Braking assist after a collision (p. 417)
for vehicles with manual transmission) when • Hill Start Assist (p. 416)
selecting this ignition mode. • City Safety™ (p. 333)
• Hill Descent Control* (p. 437)
408 * Option/accessory.
STARTING AND DRIVING
Brakes wheels from locking and help maintain steering Symbols in the instrument panel
The brake pedal is used to apply the vehicle's control when braking. Vibrations may be felt from
Symbol Meaning
regular brakes, which are part of the brake sys- the brake pedal when ABS is operating, which is
tem. normal. Check the brake fluid level. If the
The vehicle is equipped with two brake circuits. If After the vehicle is started, a brief test of the level is low, fill brake fluid and
one brake circuit is damaged, the brake pedal will ABS system is automatically performed when the check to determine the reason for
go down further when depressed. More pressure driver releases the brake pedal. An additional the loss of brake fluid.
A
will then be required from the driver for normal automatic test of the system may be performed
braking effect. when the vehicle is traveling at a low speed. Dur-
ing the test, the brake pedal may feel as though it
The driver's pressure on the brake pedal is
is pulsating.
enhanced by a power braking function.
B
WARNING
Steady glow for 2 seconds after
Power braking only functions if the engine is
running. the engine is started: Automatic
function check.
If the brake pedal is used when the engine is A Steady glow for more than 2 sec-
turned off, the pedal will feel stiffer than usual onds: Fault in the ABS system. The
and greater pressure must be applied to brake vehicle's regular brake system is
the vehicle. still working, but without the ABS
function.
In very hilly areas or when driving with a heavy
load, engine braking in manual gear should be B
Anti-lock brakes
The vehicle is equipped with an Anti-lock Braking
System (ABS), which can help prevent the
}}
* Option/accessory. 409
STARTING AND DRIVING
410
STARTING AND DRIVING
}}
411
STARTING AND DRIVING
|| Related information Activating and deactivating the Symbol in the instrument panel
• Activating and deactivating the parking brake parking brake Symbol Meaning
(p. 412) Use the parking brake to help keep the vehicle
The symbol will be illuminated
• Parking on a hill (p. 414) stationary when it is parked.
when the parking brake is acti-
• Parking brake malfunction (p. 414) Activating the parking brake vated.
• Auto-hold brakes (p. 415)
A flashing symbol indicates that a
A
fault has been detected. Read the
message in the instrument panel.
A Canadian models.
B US models.
Automatic activation
The parking brake is applied automatically:
412
STARTING AND DRIVING
Deactivating manually
1. Depress the brake pedal firmly.
2. Press the control.
> The parking brake will release and the
symbol in the instrument panel will go out.
413
STARTING AND DRIVING
414
STARTING AND DRIVING
NOTE
When braking to a stop on an uphill or down-
hill gradient, depress the brake pedal with
slightly more force than usual before releas- B
ing to ensure that the vehicle cannot move at
A Canadian models.
all. B US models.
415
STARTING AND DRIVING
Activating and deactivating Auto- • The function will remain off until it is reactiva- Hill Start Assist
hold at a standstill ted. The function for assisting when starting the vehi-
The Auto-hold brake function at a standstill is • When Auto-hold is switched off, Hill Start cle on inclines, Hill Start Assist (HSA), helps
activated with the button in the tunnel console. Assist (HSA) will remain active to help pre- prevent the vehicle from rolling backward when
vent the vehicle from rolling backward when starting on an uphill gradient. When backing up
starting up a hill. a hill, HSA helps prevent the vehicle from rolling
forward.
Related information The function retains pressure from the brake
• Auto-hold brakes (p. 415) pedal in the brake system for several seconds
after the brake pedal has been released.
This temporary braking effect is released after a
few seconds or when the driver begins driving.
Hill Start Assist is available even if the Auto-hold
brake function is switched off.
Related information
– Press the button in the tunnel console to • Auto-hold brakes (p. 415)
activate or deactivate the function. • Brakes (p. 409)
> The indicator light in the button will illumi-
nate when the function is activated. The
function will remain active the next time
the vehicle is started.
416
STARTING AND DRIVING
}}
* Option/accessory. 417
STARTING AND DRIVING
|| Symbol Meaning Gear selector positions for Select P when the vehicle is parked or when star-
automatic transmissions ting the engine. The vehicle must be stationary
Information and messages related In vehicles with an automatic transmission, the when Park is selected.
to the transmission. Follow the rec- system selects the optimal gear for the current To move the gear selector from Park, the brake
ommendations provided. driving conditions. The transmission also has a pedal must be depressed and the ignition in
manual mode. mode II.
Hot or overheated transmission.
Follow the recommendations provi- When parking – apply the parking brake before
ded. shifting to Park.
418 * Option/accessory.
STARTING AND DRIVING
* Option/accessory. 419
STARTING AND DRIVING
Related information
• Gear selector positions for automatic trans-
"-": Shift down one gear. missions (p. 418)
– Pull one of the paddles toward the steering After each gear shift, a number indicating the
wheel and then release. current gear will be displayed in the instrument
panel.
420 * Option/accessory.
STARTING AND DRIVING
Related information
• Gear selector positions for automatic trans-
missions (p. 418)
• Deactivating the automatic shiftlock (p. 421)
421
STARTING AND DRIVING
Related information
• Gear selector positions for automatic trans-
missions (p. 418)
422 * Option/accessory.
STARTING AND DRIVING
Related information
higher speeds. In normal driving conditions, most • Brakes
of the engine's power is directed to the front • Pneumatic suspension* and shock absorbers
• Gear selector positions for automatic trans-
wheels. When the vehicle is stationary, all-wheel
missions (p. 418)
drive is always activated in preparation for maxi- • Instrument panel
mum traction during acceleration. • Start/Stop function
All-wheel drive reacts differently depending on • Climate control settings
which drive mode* is selected.
Select the drive mode that is best suited to the
Related information current driving conditions. Keep in mind that not
• Drive modes* (p. 423) all drive modes are available in all situations.
}}
* Option/accessory. 423
STARTING AND DRIVING
In Off road mode, a compass will be displayed Steering response is faster, suspension is stiffer
between the speedometer and the tachometer in and ground clearance is lower to help reduce
the instrument panel. body roll when cornering.
The Start/Stop function is deactivated.
NOTE INDIVIDUAL
This drive mode is not designed to be used • Customizes drive mode to personal preferen- Settings view3 for Individual drive mode.
for normal street driving. ces.
1. Tap Settings in the Top view.
3 The image is schematic and the details may vary depending on vehicle model or software update.
424
STARTING AND DRIVING
2. Tap My Car Individual Drive Mode and Changing drive mode* If a drive mode is grayed out in the pop-up menu,
select Individual Drive Mode. The drive mode is changed using the control in it cannot be selected.
the tunnel console.
3. Under Presets, select one of the following Related information
Select the drive mode that is best suited to the
drive modes as a basis: Eco, Comfort or
current driving conditions. Keep in mind that not • Drive modes* (p. 423)
Dynamic.
all drive modes are available in all situations. • Activating and deactivating ECO drive mode
The following settings can be modified: using the function button (p. 428)
To change drive mode:
• Driver Display • Activating and deactivating Low Speed Con-
trol* using the function button (p. 436)
• Steering force
• Powertrain Characteristics
• Activating and deactivating Hill Descent Con-
trol* using the function button (p. 438)
• Brake Characteristics
• Suspension Control
• ECO Climate
• Start/Stop.
Related information
• Changing drive mode* (p. 425)
• ECO drive mode (p. 426)
• Economical driving (p. 438) 1. Press the DRIVE MODE control.
• Start/Stop function (p. 428) > A pop-up menu will appear in the center
• Low Speed Control* (p. 435) display.
• Hill Descent Control* (p. 437) 2. Roll the wheel upward or downward to the
desired drive mode.
• All Wheel Drive (AWD)* (p. 423)
3. Press the drive mode control or tap its button
in the center display to confirm the selection.
> The selected drive mode is shown in the
instrument panel.
* Option/accessory. 425
STARTING AND DRIVING
ECO drive mode speed is reduced to idling speed to reduce fuel • The gradient of the downgrade is more than
The Eco drive mode optimizes the vehicle's driv- consumption. approximately 6%.
ing characteristics for more fuel-efficient and This function is most effective in driving situa- • The steering wheel paddles* are being used
eco-friendly driving. tions where the vehicle can roll freely for a long for manual shifting.
Use this mode to save fuel and promote eco- distance, e.g. on roads with slight downgrades or Deactivating and turning off Eco Coast
friendly driving. when a decrease in speed is anticipated, such as In certain situations, it may be advisable to deac-
When ECO mode is activated, the following cha- when approaching an area with a lower speed tivate or turn off Eco Coast so that engine brak-
racteristics are modified: limit. ing can be used. These situations might include
Activating Eco Coast driving down steep hills or before passing
• The automatic transmission's shifting points.
another vehicle to help ensure this can be done
The function is activated when the accelerator
• Engine control and accelerator pedal
pedal is fully released and the following condi- as safely as possible.
response.
tions are met: Deactivate Eco Coast by:
• Eco Coast functionality is activated and
engine braking is disabled when the acceler- • Eco drive mode is activated. • Pressing the accelerator or brake pedal.
ator pedal is released at speeds between • The gear selector is in D. • Moving the gear selector to manual mode.
65 and 140 km/h (40 and 87 mph). • The vehicle's speed is approximately • Using the steering wheel paddles* to shift.
• Some of the climate system settings will be 65-140 km/h (40-87 mph).
Turn off Eco Coast by:
reduced or switched off. • The gradient of the downgrade is less than
• The suspension's self-leveling function* will approximately 6%. • Switching drive mode* or switching off drive
lower ground clearance to help reduce wind mode Eco in Function view.
COASTING will be displayed in the instrument
resistance. panel when Eco Coast is being used. It is possible to roll short distances even without
Eco Coast in order to help conserve fuel. How-
• Information will be shown in the ECO gauge Limitations
in the instrument panel to help promote ever, for the best fuel economy, Eco Coast should
Eco Coast is not available if: be activated and used to roll longer distances.
more eco-friendly and economical driving.
• The engine and/or transmission are not at
Cruise control Eco Cruise
Coast function Eco Coast normal working temperatures.
Eco Coast essentially deactivates engine braking, When cruise control is activated in the Eco drive
• The gear selector is moved from D to manual mode, the vehicle's acceleration and deceleration
allowing the vehicle's kinetic energy to be used shifting mode.
to roll greater distances. When the driver releases will be slower than in other drive modes to help
the accelerator pedal, the transmission is auto- • The vehicle's speed is not within the further conserve fuel. Because of this, the vehi-
matically disengaged from the engine. Engine 65-140 km/h (40-87 mph) range. cle's actual speed may be slightly above or below
the set speed.
426 * Option/accessory.
STARTING AND DRIVING
* Option/accessory. 427
STARTING AND DRIVING
Activating and deactivating ECO Start/Stop function Driving with the Start/Stop function
drive mode using the function Start/Stop is a function that temporarily switches Start/Stop is a function that temporarily turns off
button off the engine when the vehicle has stopped, the engine when the vehicle is stationary and
Vehicles equipped with drive mode controls in e.g. at a traffic light or in heavy traffic, and then then automatically starts it again when the vehi-
the tunnel console have a function button for starts it again automatically when the brake cle starts moving.
Eco drive mode in the center display's Function pedal is released. The Start/Stop function is available when the
view. engine is started and can be activated if certain
The Start/Stop function reduces fuel consump- conditions are met. The instrument panel indi-
When the engine is switched off, ECO mode is tion, which helps to reduce exhaust emissions. cates if the function is available, active or not
deactivated and must therefore be reactivated The system makes it possible to drive more eco- available.
each time the engine is started. ECO will be dis- nomically and climate-smart by letting the engine
played in the instrument panel when the function All of the vehicle's ordinary systems, such as
auto-stop when appropriate. lighting, radio, etc. function normally when the
is activated.
engine has been auto-stopped. Certain functions
Related information
Selecting Eco drive mode in the center • Driving with the Start/Stop function (p. 428)
may be temporarily reduced, however, such as
display's Function view the climate system's blower speed or extremely
– Tap the Driving Mode ECO button to acti- • Conditions for the Start/Stop function high audio system volume.
(p. 430)
vate or deactivate the function.
• Drive modes* (p. 423) Auto-stop
To auto-stop the engine:
• Stop the vehicle by applying the brakes and
keep the brake pedal depressed. The engine
will auto-stop.
In Eco or Comfort4 drive mode, the engine may
> An indicator light in the button will illumi- auto-stop before the vehicle has completely stop-
nate when the function is activated. ped.
With Adaptive Cruise Control or Pilot Assist acti-
Related information
vated, the engine will auto-stop after approxi-
• ECO drive mode (p. 426)
mately three seconds.
• Changing drive mode* (p. 425)
• Drive modes* (p. 423)
428 * Option/accessory.
STARTING AND DRIVING
* Option/accessory. 429
STARTING AND DRIVING
Temporarily deactivating the Start/ Conditions for the Start/Stop • the road gradient is very steep.
Stop function function • the hood is open.
In certain situations, it may be advisable to tem- Certain conditions must be met for Start/Stop to
• driving at high altitude and the engine has
porarily turn the Start/Stop function off. function. not reached its normal operating tempera-
To turn off Start/Stop, tap the ture.
Start/Stop function button in If any condition is not met, this will be indicated in
the center display's Function the instrument panel. • ABS has been activated.
view. The indicator light in the The engine does not auto-stop • hard braking (even if the ABS system has
button will go out when the not been activated).
The engine will not auto-stop if:
function has been turned off. • many starts during a short period of time
• the vehicle has not reached a speed of have triggered the starter motor's overheat-
The function will remain turned off until: ca 10 km/h (6 mph) after starting. ing protection.
• it is reactivated • after several auto-stops, the speed must
• a trailer's electrical system is connected to
• the drive mode is changed to Eco or Comfort again exceed approximately ca 10 km/h the vehicle's electrical system.
(6 mph) before the next auto-stop.
• the engine is restarted. • the transmission is not running at its normal
• the driver's seat belt is unbuckled. operating temperature.
Related information • the start battery's charge is below the mini-
• Driving with the Start/Stop function (p. 428) • The gear selector is in mode M (±).
mum level.
• Conditions for the Start/Stop function • the engine is not running at its normal oper- The engine does not auto-start
(p. 430) ating temperature. The engine will not auto-start after an auto-stop
if:
• the ambient temperature is under approxi-
mately -5 °C (23 °F) or over approximately • the driver is not wearing a seat belt, the gear
30 °C (86 °F). selector is in the P position and the driver's
door is open. The engine must be started
• windshield heating is activated.
normally.
• the climate system settings and the actual
climate in the passenger compartment differ. The engine auto-starts while the brake
• the vehicle is backing up. pedal is depressed
In the following situations, the engine will auto-
• the start battery's temperature is above or
start even if the brake pedal is depressed:
below the permitted limits.
• the driver is turning the steering wheel hard.
430
STARTING AND DRIVING
• High levels of condensation on the inside of • Temporarily deactivating the Start/Stop func-
the windows. tion (p. 430)
• the climate system settings and the actual
climate in the passenger compartment differ.
• Electrical current consumption is temporarily
high or the start battery's charge is below the
minimum level.
• The brake pedal is pumped repeatedly.
• The hood is open.
• The vehicle begins to roll or increases speed
slightly if the engine auto-stopped before the
vehicle was at a standstill.
• The driver's seat belt is unbuckled with the
gear selector in the D or N positions.
• The gear selector is moved from D to R or M
(±).
• The driver's door is opened with the gear
selector in D. An audible signal and a text
message informs the driver that the ignition
is on.
WARNING
Do not open the hood if the engine has auto-
stopped. Turn off the engine by switching off
the ignition before lifting the hood.
Related information
• Start/Stop function (p. 428)
• Driving with the Start/Stop function (p. 428)
431
STARTING AND DRIVING
Leveling control* and suspension and are adjusted continuously according to the clearance may vary depending on e.g. ambient
The vehicle's leveling control system adjusts the road surface and the vehicle's acceleration, brak- temperature, how the vehicle is loaded, if loading
suspension and shock absorbers automatically ing and cornering. mode is used, which drive mode is selected after
to help provide good comfort and control while the engine is started, etc.
The instrument panel indicates
driving. Leveling can also be controlled manually when the suspension level is The level may also be adjusted a period after the
to facilitate loading or getting in and out of the being adjusted. vehicle is parked. This is to compensate for any
vehicle. height changes that may occur due to tempera-
ture changes in the air springs when the vehicle
Pneumatic suspension and shock cools.
absorbers
The system is adapted to the selected drive The level cannot be adjusted when any of the Transporting
mode and vehicle speed. The pneumatic suspen- side doors or the tailgate is open. When transporting the vehicle on a ferry, train or
sion reduces the vehicle's ground clearance at truck, only secure (lash) the vehicle around the
higher speeds to reduce air resistance and Parking tires, not using any other parts of the chassis.
increase stability. The shock absorbers are nor- When parking, make sure that there is adequate Changes in the pneumatic suspension may occur
mally set to provide the best possible comfort space above and below the vehicle since ground during transport, which could adversely affect the
lashing and result in damage.
432 * Option/accessory.
STARTING AND DRIVING
Suspension Level control performance has been temporarily reduced due to extensive system use. If this
Temporarily reduced performence message appears frequently (e.g. several times in one week) contact a workshopA.
Suspension failure A critical fault has occurred. Stop safely, have the car towed to a workshopA.
Stop safely
}}
433
STARTING AND DRIVING
Related information
• Leveling control settings* (p. 435)
• Drive modes* (p. 423)
434 * Option/accessory.
STARTING AND DRIVING
Leveling control settings* 1. Tap Settings in the Top view. Low Speed Control*
The vehicle can be lowered or raised to make it 2. Tap My Car Mirrors and Convenience. The low-speed function, Low Speed Control
easier to load or for passengers to get in and (LSC), facilitates and improves control and trac-
out. 3. Select Easy Entry and Exit Suspension tion on rough roads and slippery surfaces, e.g.
Control. when towing a trailer on grass or up boat ramps.
Turn off leveling control before lifting the vehicle
with a jack to help avoid problems with the > When the vehicle is parked and the In vehicles equipped with drive mode control*,
pneumatic suspension. engine is turned off, the level is lowered. the function is included in the Off Road drive
(Level adjustment will stop if a side door mode.
Adjusting loading mode is opened and will resume after a slight Low Speed Control is designed for driving on
delay when the door has been closed.) rough roads and when towing trailers at low
When the engine is started and the vehi- speeds, up to approximately 40 km/h (25 mph).
cle begins to move, the level will be raised
to the height set by the selected drive When driving at low speeds, LSC prioritizes low
mode. gears and all-wheel drive to help avoid wheel spin
and improve traction on all wheels. The accelera-
Disable Leveling Control
tor pedal will be less responsive to improve trac-
In certain situations, this function must be turned
tion and speed control at low speeds.
off, e.g. before the vehicle is raised using a jack*.
The level difference caused by raising the vehicle The function is activated together with Hill
with a jack could cause problems with the pneu- Descent Control (HDC), which makes it possible
matic suspension. to control speed going down steep hills using the
accelerator pedal and reduces the need to use
Turning off the function in the center display: the brake pedal. The system makes it possible to
Use the buttons in the cargo compartment to maintain a low and uniform speed when driving
1. Tap Settings in the Top view.
raise or lower the rear section of the vehicle to down steep hills.
facilitate loading or unloading the vehicle or con- 2. Tap My Car Parking Brake and
necting or disconnecting a trailer. Suspension.
Center display settings 3. Select Disable Leveling Control.
Easy Entry and Exit Suspension Control Related information
The vehicle can be lowered to make it easier to • Leveling control* and suspension (p. 432)
get in and out.
• Loading recommendations (p. 564)
Activating easy entry in the center display:
}}
* Option/accessory. 435
STARTING AND DRIVING
Related information
• Activating and deactivating Low Speed Con- > An indicator light in the button will illumi-
trol* using the function button (p. 436) nate when the function is activated.
• Changing drive mode* (p. 425)
When the engine is switched off, the function will
• Hill Descent Control* (p. 437) be automatically deactivated.
• All Wheel Drive (AWD)* (p. 423)
NOTE
The function is deactivated when driving at
high speeds and must be reactivated at lower
speeds if so desired.
436 * Option/accessory.
STARTING AND DRIVING
Hill Descent Control* return to very low speed regardless of how steep NOTE
The function for assisting when driving downhill, the hill is and without the brakes needing to be
applied. The brake lights will illuminate when the The function is deactivated when driving at
Hill Descent Control (HDC), is a low-speed
function is activated. high speeds and must be reactivated at lower
function with increased engine braking. The
speeds if so desired.
function makes it possible to increase or The driver can brake to stop or slow the vehicle
decrease the vehicle's speed on steep downhill at any time by depressing the brake pedal.
gradients by only using the accelerator pedal, Related information
HDC is activated along with Low Speed Control
without applying the brakes. • Activating and deactivating Hill Descent Con-
(LSC), which facilitates and improves traction and trol* using the function button (p. 438)
In vehicles equipped with drive mode control*, control on rough and slippery surfaces. The sys-
the function is included in the Off Road drive tem is intended to be used at low speeds, up to • Changing drive mode* (p. 425)
mode. approximately 40 km/h (25 mph). • Low Speed Control* (p. 435)
HDC is designed for driving on rough roads at To keep in mind when using HDC • All Wheel Drive (AWD)* (p. 423)
low speeds and downhill gradients with slippery • If the function is switched off while driving on
or otherwise difficult road surfaces. The driver a steep downhill gradient, braking effect will
does not need to use the brake pedal but can be gradually reduced.
instead focus on steering.
• HDC can be used in gear positions D and R,
and in manual gears 1 or 2.
WARNING
• It is not possible to manually shift to third
HDC is only intended to be a supplementary gear or higher when HDC is active.
braking aid and it does not function in all sit-
uations.
NOTE
The driver is always ultimately responsible for
operating the vehicle in a safe manner. When LSC with HDC is activated, the feel of
the accelerator pedal and engine response
will change.
Function
Hill Descent Control allows the vehicle to move
forward or backward at very low speeds assisted NOTE
by the brake system. The driver can increase the
This drive mode is not designed to be used
speed by pressing the accelerator pedal. When
for normal street driving.
the accelerator pedal is released, the vehicle will
* Option/accessory. 437
STARTING AND DRIVING
438 * Option/accessory.
STARTING AND DRIVING
• Fuel consumption is increased at high Related information Preparing for a long trip
speeds - air resistance increases with speed. • Drive-E ‒ purer driving pleasure (p. 27) It is important to have the vehicle's systems and
• Remove unnecessary items from the vehicle • ECO drive mode (p. 426) equipment checked carefully before driving long
- the heavier the load, the higher the fuel distances.
consumption.
• Checking tire pressure (p. 535)
Check that:
• Maintain the correct pressure in the tires and • the engine is running properly and that fuel
check pressure regularly. consumption is normal
• The type of tires used could affect fuel con- • there are no leaks (fuel, oil or other fluid)
sumption - consult a retailer for advice on
• the brake pedal is functioning optimally
suitable tires.
• all lights are working ‒ adjust the headlight
• Do not use winter tires after the winter sea- height if the vehicle is carrying a heavy load
son has ended.
• tire tread depth and air pressure are at cor-
• Roof loads increase air resistance and rect levels. Change to snow tires when driv-
increase fuel consumption. Remove roof ing in areas where there is a risk of snowy or
boxes, ski racks, etc. that are not in use. icy roads.
• Avoid driving with the windows open.
• the start battery is sufficiently charged
• Using the trip computer's fuel consumption
• the wiper blades are in good condition
indicators can help you learn how to drive
more economically. Related information
Other factors that decrease fuel • Checking tire pressure (p. 535)
consumption • Filling washer fluid (p. 632)
• Dirty air cleaner. • Winter driving (p. 440)
• Dirty engine oil and clogged oil filter. • Economical driving (p. 438)
• Incorrect front-end alignment. • Vehicle modem settings (p. 511)
• Incorrect wheel alignment. • Loading recommendations (p. 564)
Some of the above items and others are checked • Driving with a trailer (p. 449)
as part of Volvo's standard maintenance sched-
ule. • Pilot Assist (p. 309)
}}
439
STARTING AND DRIVING
440
STARTING AND DRIVING
Driving through standing water CAUTION Opening/closing the fuel filler door
Driving the vehicle through a deep pool of stand- The vehicle must be unlocked before the fuel
ing water on a water-covered roadway is called • Engine damage could occur if water
filler door can be opened5.
enters the air cleaner.
fording. This must be done with great caution. An arrow next to the fuel pump
The vehicle can be driven through water up to a • If water enters the transmission, the lubri- symbol in the instrument panel
depth of 45 cm (17.7 in) at no more than walking cating ability of the oils is reduced and indicates the side of the vehicle
speed. Be particularly careful when driving the service life of these systems is short- on which the fuel filler door is
through flowing water. ened. located.
When driving through standing water, drive slowly • Damage to any component, engine,
and do not stop the vehicle. When you have transmission, turbocharger, differential or
its internal components caused by flood- 1. Open the fuel filler door by pressing lightly
passed the water, press lightly on the brake pedal on its rear edge.
and check that the brakes are functioning prop- ing, vapor lock or insufficient oil is not
erly. Water, mud, slush, etc. can make the brake covered under warranty. 2. After refueling, press the fuel filler door
linings slippery, resulting in delayed braking • If the engine stalls while the vehicle is in lightly to close it.
effect. water, do not attempt to restart it. Have
Related information
the vehicle towed out of the water to a
• If the vehicle is equipped with contacts for an
workshop. An authorized Volvo workshop • Refueling (p. 442)
electric heater or trailer coupling, clean these
is recommended. Risk of engine failure.
after driving in water or mud.
• Do not allow the vehicle to stand in water up
to the sills any longer than absolutely neces- Related information
sary. This could result in electrical malfunc- • Recovery (p. 455)
tions. • Low Speed Control* (p. 435)
5 Only locking and unlocking using the remote key, Passive Entry or Volvo On Call will affect the status of the fuel filler door.
* Option/accessory. 441
STARTING AND DRIVING
442
STARTING AND DRIVING
the emission control system and could result in Volvo permits the use of the following "oxygen- Octane rating
loss of emission warranty coverage. State and ated" fuels. However, the specified octane ratings Volvo demands premium fuel (91 octane6 or
local vehicle inspection programs will make must still be met. higher) for all T5, T6 and T8 engines. See both
detection of misfueling easier, possibly resulting supplied decal examples.
Alcohol - Ethanol
in emission test failure for misfueled vehicles.
Fuels containing up to 10% ethanol by volume
may be used. Ethanol may also be referred to as
NOTE Ethyl alcohol, or "Gasohol".
Some U.S. and Canadian gasolines contain an Ethers - MTBE/ETBE: Fuels containing up to
octane enhancing additive called methyl- 15% MTBE/ETBE may be used.
cyclopentadienyl manganese tricarbonyl
(MMT). If such fuels are used, your Emission Methanol
Control System performance may be affected, Do not use gasolines containing methanol
and the Check Engine Light (malfunction (methyl alcohol, wood alcohol). This practice can
indicator light) located on your instrument result in vehicle performance deterioration and
panel may light. If this occurs, please return can damage critical parts in the fuel system. Such
your vehicle to a trained and qualified Volvo damage may not be covered under the New
service technician for service. Vehicle Limited Warranty.
Related information
Gasoline containing alcohol and ethers,
• Octane rating (p. 443)
"Oxygenated fuels"
Some fuel suppliers sell gasoline containing • Opening/closing the fuel filler door (p. 441)
"oxygenates" which are usually alcohols or • Refueling (p. 442)
ethers. In some areas, state or local laws require • Emission controls (p. 445)
that the service pump be marked indicating use
of alcohols or ethers. However, there are areas in
which the pumps are unmarked. If you are not
sure whether there is alcohol or ethers in the
gasoline you buy, check with the service station
operator. To meet seasonal air quality standards,
some areas require the use of "oxygenated" fuel.
6 AKI (Anti Knock Index) is an average value of RON (Research Octane Number) and MON (Motor Octane Number) - (RON)+(MON)/2 }}
443
STARTING AND DRIVING
|| Minimum octane TOP TIER Detergent Gasoline Many fuels contain benzene as a solvent.
Volvo endorses the use of "TOP TIER Detergent Unburned benzene has been strongly linked to
Decals
Gasoline" where available to help maintain certain forms of cancer. If you live in an area
engine performance and reliability. TOP TIER where you must fill your own gas tank, take pre-
Detergent Gasoline meets a new standard jointly cautions. These may include:
established by leading automotive manufactures
• standing upwind away from the filler nozzle
to meet the needs of today's advanced engines. while refueling
Qualifying gasoline retailers (stations) will, in
most cases, identify their gasoline as having met • refueling only at gas stations with vapor
the "TOP TIER Detergent Gasoline" standards. recovery systems that fully seal the mouth of
the filler neck during refueling
NOTE • wearing neoprene gloves while handling a
fuel filler nozzle.
Information about TOP TIER Detergent Gaso-
line is available at www.toptiergas.com. Use of Additives
Sample fuel pump octane label6. With the exception of gas line antifreeze during
winter months, do not add solvents, thickeners, or
NOTE other store-bought additives to your vehicle's
When switching to higher octane fuel or fuel, cooling, or lubricating systems. Overuse may
changing gasoline brands, it may be neces- damage your engine, and some of these additives
sary to fill the tank more than once before a contain organically volatile chemicals. Do not
difference in engine operation is noticeable. needlessly expose yourself to these chemicals.
6 AKI (Anti Knock Index) is an average value of RON (Research Octane Number) and MON (Motor Octane Number) - (RON)+(MON)/2
7 For supplementary information - see the car's Service and Warranty Booklet.
444
STARTING AND DRIVING
445
STARTING AND DRIVING
Overheating of engine and the vehicle safely and letting the engine idle Related information
transmission for a few minutes to let the transmission • Refilling coolant (p. 590)
cool.
In demanding driving conditions, such as driving • Driving with a trailer (p. 449)
in mountainous areas or hot weather, there is a • If the vehicle begins to overheat, the air con-
• Preparing for a long trip (p. 439)
risk of the engine or transmission overheating, ditioning may be temporarily switched off.
especially when carrying heavy loads. • Gear indicator* (p. 422)
• After a prolonged period of driving in
demanding conditions, do not turn off the
• Engine power may be temporarily limited.
engine immediately after stopping.
• Remove any auxiliary lights mounted in front
of the grille when driving in hot weather.
NOTE
• If the temperature in the engine's cooling
system becomes too high, a warning symbol It is normal for the engine's cooling fan to
will appear in the instrument panel along with operate for a short time after the engine is
the message Engine temperature High switched off.
temperature Stop safely. Pull over to a
safe location and let the engine idle for a few Symbols in the instrument panel
minutes to cool down.
Symbol Meaning
• If the message Engine temperature High
temperature Turn off engine or Engine High engine temperature. Follow
coolant Level low, turn off engine is dis- the recommendations provided.
played, stop the vehicle and turn off the
engine.
Low coolant level. Follow the rec-
• If the transmission begins to overheat, an
ommendations provided.
alternative gear shifting program will be
selected. An integrated protective function
will also be activated, the warning symbol will
Transmission hot/overheated/cool-
illuminate and the message Transmission
ing. Follow the recommendations
warm Reduce speed to lower
provided.
temperature or Transmission hot Stop
safely, wait for cooling will be displayed in
the instrument panel. Follow the recommen-
dations given by reducing speed or stopping
446 * Option/accessory.
STARTING AND DRIVING
Battery drain Jump starting using another battery 4. Clamp the red jumper cable onto the auxiliary
The electrical functions in the vehicle drain the If the start battery is discharged, current from battery's positive (+) terminal (1).
battery to varying degrees. Avoid using ignition another battery can be used to start the vehicle.
mode II when the engine is switched off. Use CAUTION
ignition mode I instead, as this uses less electri- Connect the jump cable carefully to prevent
cal current. short circuits with other components in the
Note that certain accessories may also drain engine compartment.
power from the electrical system. Do not use
functions that use a lot of electrical current when 5. Fold back the cover over your vehicle's posi-
the engine is turned off. Examples of such func- tive (+) jump start terminal (2).
tions are:
6. Clamp the other end of the red jumper cable
• blower to your vehicle's positive (+) jump start termi-
• headlights nal (2).
• windshield wipers 7. Clamp the black jumper cable onto the auxili-
ary battery's negative (-) terminal (3).
• audio system (especially at high volume). Jumper cable connecting points.
If the starter battery voltage is low, a message is To avoid short circuits or other damage, the fol- 8. Clamp the other end of the black jumper
shown in the driver display. The vehicle's energy- lowing steps are recommended when jump star- cable to your vehicle's negative (-) ground
saving function will then turn off or reduce certain ting the battery using another battery: point (4).
functions, such as the blower and/or the audio 1. Put the ignition in mode 0. 9. Make sure the jumper cables are securely
system. attached to help prevent sparks while jump
2. Make sure the auxiliary battery (the battery starting.
– Charge the battery by starting the engine used to jump start the discharged battery)
and let it run for at least 15 minutes (driving has a voltage of 12 volts. 10. Start the engine of the assisting vehicle and
charges the battery faster than letting the let it run for a few minutes at a higher idling
engine idle). 3. If the auxiliary battery is in another vehicle, speed than normal, about 1500 rpm.
turn off that vehicle's engine and make sure
Related information that the vehicles are not touching each other.
• Start battery (p. 598)
• Ignition modes (p. 407)
}}
447
STARTING AND DRIVING
|| 11. Start the engine of the vehicle with the dead WARNING Detachable towbar*
battery. Volvo recommends the use of Volvo towbars
• Batteries generate hydrogen gas, which
that are specially designed for the vehicle.
is flammable and explosive.
CAUTION
Do not touch the connections between the
• Do not connect the jumper cable to any NOTE
part of the fuel system or to any moving
cable and the vehicle during the start attempt. The optional detachable trailer hitch may not
parts. Avoid touching hot manifolds.
Risk of sparking. be available in all markets or on all models.
• Battery fluid contains sulfuric acid. Do not Consult your Volvo retailer.
allow battery fluid to contact eyes, skin,
12. Remove the jumper cables in the reverse fabrics or painted surfaces.
order ‒ first the black cables and then the
red cables. • If contact occurs, flush the affected area
immediately with water. Obtain medical
Make sure that none of the clamps of the help immediately if eyes are affected.
black jumper cables come into contact with
either vehicle's positive (+) jump start termi- • Never expose the battery to open flame
or electric spark. Do not smoke near the
nals or either of the red jumper cable's con-
battery. Failure to follow the instructions
nected clamps.
for jump starting can lead to injury.
WARNING
Related information
PROPOSITION 65 WARNING! Battery posts,
terminals, and related accessories contain
• Starting the vehicle (p. 404)
lead and lead compounds, chemicals known • Ignition modes (p. 407)
to the state of California to cause cancer and Ball holder
reproductive harm. Wash hands after han-
• Adjusting the steering wheel (p. 203)
dling. • Selecting ignition mode (p. 408) Cotter pin
Towbar assembly
Locking bolt
448 * Option/accessory.
STARTING AND DRIVING
Installing the ball holder Stowing the ball holder Driving with a trailer
1. If necessary, remove the cotter pin from the There are a number of things to consider when
locking bolt and slide the locking bolt out of WARNING towing a trailer, such as the towbar, the trailer
the towbar assembly. and how the load is distributed in the trailer.
When not in use, the detachable ball holder
2. Slide the ball holder into the towbar assem- should always be properly stowed in the des- Load-carrying capacity is determined by the vehi-
bly. ignated location under the floor of the cargo
cle's curb weight. The total weight of all passen-
compartment.
3. Align the hole in the ball holder with the one gers and any installed accessories, e.g. towbar,
in the towbar assembly. reduces the vehicle's load-carrying capacity by
Related information the corresponding amount.
4. Slide the locking bolt through the towbar • Driving with a trailer (p. 449)
assembly/ball holder.
• Towing capacity and tongue weight (p. 642) • Towbars used on the vehicle must be
approved for the applicable use.
5. Insert the cotter pin in the hole at the end of
the locking bolt. • Distribute the load on the trailer so that the
weight on the towbar complies with the
specified maximum towball weight. The
WARNING
tongue weight is calculated as part of the
• Be sure the towbar is securely locked in vehicle's payload.
position before attaching anything to it.
• Increase the tire pressure to the recom-
• Always attach the trailer's safety wire mended pressure for a full load.
securely to the towbar's safety wire
attachment bracket.
• The engine is subjected to more load than
usual when towing a trailer.
• Towing a trailer affects the vehicle's han-
Removing the ball holder dling, durability and driving economy.
1. Remove the cotter pin from the locking bolt
and slide the locking bolt out of the ball • Do not drive with a heavy trailer when the
holder/towbar assembly. vehicle is very new. Wait until the mileage
has reached at least 1000 km (620 miles).
2. Pull the ball holder out of the towbar assem-
bly. • On long and steep downgrades, the vehicle's
brakes are subjected to much more load
than usual. When manually shifting, down-
shift and adapt speed accordingly.
}}
449
STARTING AND DRIVING
450 * Option/accessory.
STARTING AND DRIVING
The automatic transmission selects the optimal Trailer Stability Assist* ments. If swaying is detected, the brakes are
gear for the current load and engine speed. (TSA8)
Trailer Stability Assist is a function applied individually on the front wheels, which has
designed to help stabilize a vehicle that is tow- a stabilizing effect on the vehicle and trailer. This
Steep inclines
ing a trailer when the vehicle and trailer have is often enough to enable the driver to regain
Do not lock the automatic transmission into a
control of the vehicle.
higher gear than what the engine can handle ‒ it begun to sway. The function is part of the Elec-
is not always preferable to drive in high gears at tronic Stability Control system ESC9. If the Trailer Stability Assist function's first
low rpm. attempt is not adequate to stop the swaying
Reasons for swaying motion, the brakes are applied on all wheels and
Parking on a hill A vehicle towing a trailer may begin to sway for engine power is temporarily reduced. As the
1. Depress the brake pedal. various reasons. Normally this only occurs at high swaying motion begins to decrease and the vehi-
2. Apply the parking brake. speeds. However, if the trailer is overloaded or cle and trailer have once again become stable,
unevenly distributed, e.g. too far back, there is a TSA stops regulating the brakes/engine power
3. Put the gear selector in P. risk of swaying even at low speeds. and the driver regains control of the vehicle.
4. Release the brake pedal. Swaying may be caused by factors such as:
Put chocks behind the wheels when the vehicle NOTE
is parked on a hill with a trailer attached.
• The vehicle and trailer are hit by a sudden,
strong crosswind. Trailer Stability Assist is deactivated if the
Starting on a hill driver selects the sport mode by deactivating
• The vehicle and trailer are traveling on an
ESC in the center display's menu system.
1. Depress the brake pedal. uneven road or over a bump.
2. Put the gear selector in D. • Sudden movements of the steering wheel.
Trailer Stability Assist may not intervene if the
3. Release the parking brake. Once swaying has begun, it can be difficult or driver tries to compensate for the swaying motion
4. Release the brake pedal and start driving. impossible to stop it. This makes the vehicle and by moving the steering wheel rapidly, because
trailer difficult to control and there is a risk of the system will then not be able to determine if it
Related information swerving into oncoming traffic or driving off the is the trailer or the driver causing the swaying.
• Trailer Stability Assist* (p. 451) road.
• Checking trailer lights (p. 452) Trailer Stability Assist function
• Towing capacity and tongue weight (p. 642) Trailer Stability Assist continuously monitors the
vehicle's movements, particularly lateral move-
• Overheating of engine and transmission
(p. 446)
* Option/accessory. 451
STARTING AND DRIVING
|| When Trailer Stability Assist is Checking trailer lights fog lights when driving with a trailer to help
activated, the ESC symbol is When connecting a trailer, make sure that all of ensure safe operation.
displayed in the instrument the lights on the trailer are functioning before
panel. starting to drive.
Checking trailer lights*
Automatic check
Trailer turn signals and brake lights When the trailer has been connected to the vehi-
If one or more of the turn signals or brake lights cle's electrical system, its lights can be checked
Related information on the trailer is not working, a symbol and mes- by automatically activating them. This function
• Driving with a trailer (p. 449) sage will be displayed in the instrument panel. helps the driver check that the trailer's lights are
• Electronic Stability Control (p. 272) The other lights on the trailer must be checked functioning correctly before starting to drive.
manually by the driver before the vehicle is driven.
In order to perform this check, the engine must
be turned off.
Symbol Message
1. When a trailer is connected to the towbar,
• Trailer turn indicator Right the message Automatic Trailer Lamp
turn indicator malfunction Check will appear in the instrument panel.
• Trailer turn indicator Left 2. Acknowledge the message by pressing the
turn indicator malfunction O button on the right-side steering wheel
• Trailer brake light Malfunc- keypad.
tion > The light check will begin.
3. Get out of the vehicle to perform the check.
> All of the lights on the trailer will begin
If any of the trailer's turn signal lights is not work- flashing, and then illuminate separately
ing, the turn signal symbol in the instrument one at a time.
panel will also flash more quickly than normal. 4. Visually check that all of the trailer's lights
Trailer rear fog light are functioning correctly.
When a trailer is connected, the vehicle's rear fog 5. After a short time, all of the trailer's lights will
light may not illuminate and rear fog light func- start flashing again.
tionality is instead transferred to the trailer. If this > The light check is completed.
is the case, check to see if the trailer is equipped
with a rear fog light before activating the vehicle's
452 * Option/accessory.
STARTING AND DRIVING
Disabling the automatic check Towing using a towline 1. Turn on the hazard warning flashers.
The automatic light check can be disabled in the This section refers to one vehicle being towed 2. Attach the towline to the towing eyelet.
center display. behind another using a towline.
3. Put the vehicle in ignition mode II – without
1. Tap Settings in the Top view. Before towing another vehicle, check applicable pressing the brake pedal, turn the start knob
2. Tap My Car Lights and Lighting. speed limit regulations. clockwise and hold it there for about
4 seconds. Release the knob, which will
3. Deselect Automatic Trailer Lamp Check. Preparations and towing automatically return to its original position.
Manual check 4. Move the gear selector to neutral (N) and
If the automatic check has been disabled, the CAUTION release the parking brake.
check can be started manually. Note that the vehicle must always be towed
If the battery charge level is too low, it may
1. Tap Settings in the Top view. with the wheels rolling forward.
not be possible to release the parking brake.
2. Tap My Car Lights and Lighting. • Do not tow a vehicle with automatic Connect an auxiliary battery to the vehicle if
transmission at a speed greater than the battery is discharged.
3. Select Manual Trailer Lamp Check. 80 km/h (50 mph) or for a distance > The towing vehicle can now start driving.
> The light check will begin. Get out of the greater than 80 km (50 miles).
vehicle to perform the check. 5. Keep the towline taut when the towing vehi-
cle slows down by applying light pressure to
Related information WARNING the brake pedal. This will help avoid jarring
• Driving with a trailer (p. 449) movements.
• Ignition mode II must be active – all air-
bags are deactivated in ignition mode I. 6. Be prepared to apply the brakes to stop the
vehicle.
• Always have the remote key in the vehicle
when it is towed. Jump starting
Do not tow the vehicle to start the engine. Use an
WARNING auxiliary battery if the start battery's charge level
is so low that the engine cannot be started.
The brake and steering servos do not work
when the engine is off – it takes
about 5 times more pressure on the brake
pedal and steering requires much more effort
than normal.
}}
453
STARTING AND DRIVING
454
STARTING AND DRIVING
4. Screw in the towing eyelet until it reaches its attempting to pull it up using the towing eyelet Recovery
stop. Fasten the eyelet securing by, for exam- may result in damage. This section refers to transporting the vehicle
ple, inserting a lug wrench* through it and If necessary, lift the vehicle using the tow truck's with a tow truck or similar vehicle.
using this as a lever. lifting device instead of using the towing eyelet. Call a professional towing service for assistance.
In certain conditions, the towing eyelet can be
WARNING used to pull the vehicle onto a flatbed tow truck.
No person or object should be behind the tow For vehicles equipped with leveling control*:
truck when the vehicle is lifted onto the bed If the vehicle is equipped with pneumatic suspen-
of the truck. sion, this feature must be turned off before the
vehicle is lifted onto a tow truck. Turning off the
CAUTION function in the center display.
The towing eyelet is only intended for towing 1. Tap Settings in the Top view.
on roads, and must not be used to pull vehi-
2. Tap My Car Parking Brake and
CAUTION cles from ditches or any similar purpose
Suspension.
involving severe strain. Call a tow truck for
It is important that the towing eye is screwed professional assistance. 3. Select Disable Leveling Control.
in securely as far as possible.
The vehicle's location and ground clearance
Related information determine if it can be lifted onto a tow truck. If
Removing the towing eyelet: • Towing using a towline (p. 453) the incline of the tow truck is too steep or if the
ground clearance under the vehicle is insufficient,
– After use, unscrew the towing eyelet and • Recovery (p. 455)
attempting to pull it up may result in damage. In
return it to its storage location. • Tool kit (p. 542) this case, the vehicle should only be lifted with
Replace the cover on the bumper. the tow truck's lifting equipment.
In certain conditions, the towing eyelet may be
used to pull the vehicle onto a flatbed tow truck. WARNING
The vehicle's position and ground clearance No person or object should be behind the tow
determines if this is possible. truck when the vehicle is lifted onto the bed
of the truck.
If the incline of the tow truck is too steep or if the
ground clearance under the vehicle is insufficient,
}}
* Option/accessory. 455
STARTING AND DRIVING
CAUTION General Save the original remote controls for future pro-
gramming (e.g. for use in another vehicle). It is
Note that the vehicle must always be towed also advisable to delete the button programming
with the wheels rolling forward. if the vehicle is sold.
Button 2
Button 3
Indicator light
456 * Option/accessory.
STARTING AND DRIVING
* Option/accessory. 457
STARTING AND DRIVING
Related information
• Using HomeLink (p. 458)
• HomeLink®* (p. 456)
• Type approval for HomeLink®* (p. 459)
458 * Option/accessory.
STARTING AND DRIVING
WARNING
The transmitter has been tested and complies
with FCC and IC rules. Changes or modifica-
tions not expressly approved by the party
responsible for compliance could void the
user's authority to operate the device.15
Rearview mirror with compass.
* Option/accessory. 459
STARTING AND DRIVING
460 * Option/accessory.
STARTING AND DRIVING
Related information
• Compass (p. 459)
• Activating and deactivating the compass
(p. 460)
461
AUDIO, MEDIA AND INTERNET
AUDIO, MEDIA AND INTERNET
The functions can be controlled using voice com- Sound settings as needed
mands, the steering wheel keypad or the center In Top view under Settings Sound, the fol-
display. The number of speakers and amplifiers lowing settings can be selected:
varies depending on the audio system installed in
the vehicle. • Tone — personal preference for bass, treble,
equalizer for example.
System updates
The audio and media system is continuously
• Balance - balance between right/left and
front/rear speakers.
improved. When the vehicle has an Internet con-
nection, system updates can be downloaded for • System Volumes – adjusts volume in the
optimal functionality; see support.volvocars.com. various systems of the car, e.g. Voice
Control, Park Assist and Phone Ringtone.
464 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Sound experience* distracting noise and the audio system sends out Apps
a counteracting sound to help reduce the unwan- The App view contains applications (apps) that
ted noise. provide access to certain vehicle services.
* Option/accessory. 465
AUDIO, MEDIA AND INTERNET
|| Swipe the center display screen from right to be downloaded when the car is connected to the Download apps
left1 to access the App view from the Home view. Internet. New apps can be downloaded when the vehicle
This view displays downloaded apps (third-party Some apps can only be used when the vehicle is is connected to the Internet.
apps) as well as apps for integrated functions, connected to the Internet. NOTE
such as FM radio.
Start an app by pressing the app in the center Data downloading can affect other services
display's app view. such as transfer data, e.g. web radio. If the
affect on other services is experienced as
Related information problematic, the download can be interrupted.
• Download apps (p. 466) Alternatively, it may be appropriate to switch
• Updating apps (p. 467) off or cancel other services.
• Deleting apps (p. 468)
• Apple® CarPlay®* (p. 493) NOTE
• Android Auto* (p. 496) When downloading using a phone, pay extra
• Internet-connected vehicle* (p. 507) attention to the data traffic costs.
• Hard disk storage space (p. 516)
• Terms of use and data sharing (p. 514) 1. Open the Download Center app in App
view.
App view. (generic illustration; basic apps vary depend- 2. Select New apps to open a list of apps that
ing on market and model)
are available but are not installed in the vehi-
Several basic apps are always available. More cle.
apps such as web radio and music services can
1 Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction.
466 * Option/accessory.
AUDIO, MEDIA AND INTERNET
3. Tap on the row for an app in order to expand Updating apps Update certain apps
in the list and get more information about the Apps can be updated when the vehicle is con- 1. Open the Download Center app in App
app. nected to the Internet. view.
4. Select Install to start the download and NOTE 2. Select Application updates to open a list
installation of the app. of all available updates.
Data downloading can affect other services
> The current status of the download and such as transfer data, e.g. web radio. If the 3. Find the desired app and select Install.
installation will be shown. affect on other services is experienced as > The update will begin.
If a download cannot be started immedi- problematic, the download can be interrupted.
ately, a message will be displayed. The Alternatively, it may be appropriate to switch Related information
app will remain in the list and it will be off or cancel other services. • Apps (p. 465)
possible to reattempt downloading. • Download apps (p. 466)
Canceling a download NOTE • Deleting apps (p. 468)
– Tap Abort to cancel a download in progress. • Handling system updates via Download Cen-
When downloading using a phone, pay extra
Note that only a download can be cancelled. An attention to the data traffic costs. ter (p. 579)
installation cannot be cancelled once it has • Internet-connected vehicle* (p. 507)
begun. If an app is being used while an update is in pro-
Related information gress, it will be restarted to complete the update.
• Apps (p. 465) Update all
• Updating apps (p. 467) 1. Open the Download Center app in App
view.
• Deleting apps (p. 468)
• Internet-connected vehicle* (p. 507)
• Handling system updates via Download Cen-
ter (p. 579)
• Hard disk storage space (p. 516)
* Option/accessory. 467
AUDIO, MEDIA AND INTERNET
468 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Starting the radio • Changing waveband and radio station Changing waveband and radio
The radio is started from the center display's (p. 469) station
App view. • Storing radio favorites (p. 471) Instructions for changing wavebands, waveband
1. Open the desired waveband (e.g. FM) from lists and radio stations in the selected list are
• Radio settings (p. 471)
App view. provided here.
• Voice control for radio and media (p. 150)
Changing wavebands
Swipe from App view on the center display and
select the desired waveband (e.g. FM) or open
the App menu in the instrument panel with the
right-side steering wheel keypad and make your
selection there.
1. Tap Library.
2. Select a radio station.
2. Select playback from Stations, Favorites or
Related information Genres.
• Radio (p. 468)
3. Tap the desired station in the list.
• Searching for a radio station (p. 470)
Favorites – only plays selected favorite channels.
}}
469
AUDIO, MEDIA AND INTERNET
|| Genres - only plays channels broadcasting the Searching for a radio station Searching for a station manually
selected genre or program type, e.g. pop, classi- The radio automatically compiles a list of the
cal, etc. radio stations that are sending out the strongest
signals in the vehicle's current location.
Changing radio stations in a selected
list
– Press or under the center display
or on the right-side steering wheel keypad.
> Move step-by-step through the selected
list.
It is also possible to change radio station in the
selected list via the center display.
470
AUDIO, MEDIA AND INTERNET
Storing radio favorites • Voice control for radio and media (p. 150) Radio settings
It is possible to add a radio a radio station in the • Radio settings (p. 471) There are a number of different radio functions
Radio favorites app and in the list of favorites that can be activated and deactivated.
• App menu in instrument panel (p. 104)
for the waveband (e.g. FM). Instructions for add-
ing and removing favorites are provided below. Canceling a traffic message
A current broadcast (e.g. a traffic message) can
Radio favorites be temporarily interrupted by pressing in the
Radio favorites shows saved right-side steering wheel keypad or tapping
favorites from all wavebands. Cancel in the center display.
}}
471
AUDIO, MEDIA AND INTERNET
NOTE
HD Radio volume may fade in and out at
times due to coverage limitations.
472 * Option/accessory.
AUDIO, MEDIA AND INTERNET
The IBOC system is referred to as a "hybrid" Ball game mode • Instead of transmitting one analog signal,
since it is both analog and digital. During hybrid This feature means that a main FM station (HD1) stations send out a bundled signal - both
operation, receivers still continue to receive the will broadcast live events, where the content of analog and digital.
analog (non-digital) signal. HD Radio receivers the programming is more important than sound • An HD Radio receiver can receive both digi-
incorporate both modes of reception, where the quality, in analog mode only to help prevent the tal and analog broadcasts. Depending on the
receiver will automatically switch to the analog delay between analog and digital broadcasting. terrain and location of the vehicle (which will
signal if the digital signal cannot be decoded or The HD Radio symbol will be white during live influence the signal strength), the receiver
is lost by the receiver. broadcasts and "Live" will be displayed next to will determine which signal to receive.
When you have tuned to an HD Radio station, the the symbol.
Related information
symbol will appear in the infotainment sys- Benefits of digital broadcasting
tem display. The symbol will be displayed in dif-
• Radio (p. 468)
• Better sound (FM sounds near CD quality
ferent colors: and AM as analog FM). • Activating and deactivating the HD Radio™
(p. 474)
• Grayed-out symbol: No HD Radio broad- • Some FM frequencies offer a greater num-
cast reception ber of listening choices through "multicast- • HD Radio™ sub-channels (p. 474)
• White symbol: the radio is actively receiving ing" (consisting of a frequency's main chan- • HD Radio™ limitations (p. 475)
an HD broadcast nel and any sub-channels that may also be • Changing waveband and radio station
available on that particular frequency.) (p. 469)
• Orange symbol: the radio is receiving an
HD broadcast with digital sound • When receiving a digital signal there is no • Searching for a radio station (p. 470)
multipath disturbance or hisses/pops/crack-
More information about HD Radio and IBOC can
ling due to outside influences.
be found on DTS, Inc.'s website, www.dts.com.
How HD Radio ™ Technology
Artist Experience™
broadcasting works
A radio station's logo and album art can be dis-
HD Radio works similarly to conventional radio
played. If a station opts to provide this informa-
and broadcasts of this type are available in many
tion, it is broadcast once every 12 minutes, which
areas of the United States. However, there are a
means that there may be a delay before the
few key differences:
logo/album art appear on the screen. The radio
can store 100 station logos so the next time the
radio is tuned to the same station, the logo will
be displayed immediately. Album art is synched
with the artist that you are currently listening to.
473
AUDIO, MEDIA AND INTERNET
Activating and deactivating the HD • HD Radio™ limitations (p. 475) HD Radio™ sub-channels
Radio™ • Opening contextual setting in the center dis- In many cases, a main HD Radio station (FM
HD Radio is deactivated when the car leaves the play (p. 135) wavebands only) will also have sub-channels
factory. offering additional types of programming or
When listening to an HD Radio station and driv- music.
ing through areas with weak HD signals (fringe
areas), you may experience that the radio repeat- Sub-channels
edly switches between analog/digital and digital/
analog reception. If this happens, it may be desir-
able to switch HD off.
Carry out the following to activate or deactivate
HD Radio:
1. Drag down the top view and tap on
Settings.
2. Press Media and AM/FM Radio.
3. Press HD Radio AM or HD Radio FM to
activate/deactivate the function.
If HD radio is deactivated, the radio will be unable Example of an HD Radio station with sub-channels
to receive digital broadcasts but it will continue to If any sub-channels are available, they will listed
function as a conventional radio (analog AM/FM below the main channel on the screen. In this
receiver). Please note that when HD is switched example, WILD-FM HD2 is a sub-channel.
off, it will not be possible to tune in to sub-chan-
nels.
Note that if you activate or deactivate HD Radio
only the selected wavelength band is affected.
Related information
• HD Radio™ (p. 472)
• HD Radio™ sub-channels (p. 474)
474
AUDIO, MEDIA AND INTERNET
475
AUDIO, MEDIA AND INTERNET
SiriusXM® Satellite radio* 2. Open the settings menu for SiriusXM® Satel-
The SiriusXM® Satellite system broadcasts from lite radio.
of a number of high elevation satellites in geo- 3. Tap Unsubscribed Services
synchronous orbit.
4. To call SiriusXM®, enter the phone number.
Listening to satellite radio They will activate the subscription of your
The digital signals from the satellites are line-of- choice. This may take several minutes.
sight, which means that physical obstructions When the subscription has been activated, tap
such as bridges, tunnels, etc, may temporarily the SiriusXM® Satellite radio icon to start the
interfere with signal reception. function and display the channel list included in
Avoid any obstructions, such as metallic objects your subscription.
transported on roof racks or in a ski box, or other
antennas that may impede signals from the Related information
SiriusXM® satellites. • Radio (p. 468)
• Using SiriusXM® Satellite radio* (p. 477)
Selecting SiriusXM® Satellite radio
mode
• Settings for SiriusXM® Satellite radio*
(p. 478)
1. From the center display's Home view, swipe
from right to left to come to App view. • SiriusXM Travel Link®* (p. 480)
476 * Option/accessory.
AUDIO, MEDIA AND INTERNET
}}
* Option/accessory. 477
AUDIO, MEDIA AND INTERNET
|| iTunes tagging • Settings for SiriusXM® Satellite radio* Settings for SiriusXM® Satellite
From the center display's Top view, tap SiriusXM (p. 478) radio*
Settings. Tap the iTunes Tagging menu. Tap • Connecting a device via the USB port There are numerous settings that can be made
the iTunes Tagging box to activate/deactivate (p. 492) to enhance your SiriusXM® Satellite radio listen-
this function and tap Close to return to Home ing experience.
view. Tap Tags List to display a list of all tagged
songs. Settings
If the function is activated, the iTunes tag button Drag down the top view and tap on Settings
will be displayed in Home view. If a song is played Media SiriusXM. The following alternatives
that you would like to buy in the iTunes store, tap will be displayed:
this button while the song is playing to tag it. If a
song with iTunes Tagging information is availa-
ble, the button will be selectable. Tap the button
to tag the song. If you would like to buy a tagged
song via iTunes, Tap the iTunes tag button.
To buy a song in iTunes, begin by connecting an
iPhone/iPod/iPad to the USB port in the tunnel
console. The iTunes tagging list will automatically
be transferred to the device and removed from
the list in the vehicle. If the device is connected
when a song is tagged, the data will automatically
be saved in the device. To purchase the song,
consult the iTunes support page.
Related information
• SiriusXM® Satellite radio* (p. 476)
• Entering characters, letters and words by
hand in the center display (p. 131)
• Settings for SiriusXM® Satellite radio*
(p. 478)
478 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Traffic Jump iTunes Tagging previously selected as a favorite will still be dis-
Tap to display a list of cities from which you can Tap to display a menu with the options: iTunes played in the list of favorites, even it has been
choose to get traffic/weather information (or Tagging and Tags List. With this feature acti- added to the skip list.
Traffic jump off to deactivate the feature). Tap vated, songs can be tagged for later purchase Skipped Categories
to select a city (JUMP will be displayed on the from the iTunes store. Tap to display a list of categories. Tap a category
Home screen next to Library). Tap Back to Game Alerts to skip (hide) it. It will not be displayed in the list
return to the list of settings or Close to return to Tap to display a list of sports. of categories.
the Home screen.
Tap a sport to display a list of teams and tap a Related information
From the Home screen, tap JUMP to activate the box on the right side of the screen to select a
function. When traffic/weather information is • SiriusXM® Satellite radio* (p. 476)
team as a favorite. An alert will then be provided
available from the selected city, the radio will when information about the team is being broad- • Using SiriusXM® Satellite radio* (p. 477)
automatically tune to the channel providing the cast.
information. When the information/announce-
ment is finished, the radio will automatically Tap Confirm below the list to return to the list of
return to the channel that you were previously lis- sports.
tening to. Tap Back to return to the list of settings or
During an announcement, tap JUMP to interrupt Close to return to the main screen.
the message and return to the station that you Unsubscribed Services
were currently listening to. If you have a SiriusXM® Satellite radio subscrip-
Alert Notifications tion, any channels not included in the subscrip-
Tap the box to activate/deactivate. When acti- tion will be listed here. Call SiriusXM™ to sub-
vated, you will be notified if a song, artist, etc. that scribe. The phone number will be shown on the
you have selected is playing. You will be asked if screen. If a cell phone is paired and connected to
you want to listen. the vehicle, tap the phone number to make the
call.
Alert Notifications Sound
Opt to receive an audible alert when one of your Skipped Stations
selected choices is being played. Tap to display a list of channels that you would
like to skip (hide). Hide channels from the chan-
Sort Channels
nel list by tapping the boxes to the right of the
Select how to sort your channels list.
screen. Skipped (hidden) channels will not be
shown in the channel list. However, a channel
* Option/accessory. 479
AUDIO, MEDIA AND INTERNET
480 * Option/accessory.
AUDIO, MEDIA AND INTERNET
• SiriusXM Travel Link®* - Sports (p. 484) SiriusXM Travel Link®* - Weather • Map view
• SiriusXM Travel Link®* - Weather (p. 481) This SiriusXM Travel Link service provides • Today
weather-related information near the vehicle, at a • 5 days
• SiriusXM Travel Link®* - Notifications
local ski resort, etc.
(p. 482) Map view
From the SiriusXM Travel Link home screen, to
display weather-related information: Tap the map to display it in full-screen mode. Tap
Back to return to the original map view.
– Tap the Weather button to display this
screen. Tap Map options to display the following alter-
natives.
At the top of the screen, the following categories
will be displayed: • Weather radar
• Areas • Winds
Tap the relevant box to the right of the option to
• Favorites
select/deselect it. Tap Done to confirm and
Tap the category of your choice. return to the previous screen or Cancel.
Search Today
Tap the magnifying glass icon. If the function is Tap to see the current temperature, or the tem-
supported in the current context, a keyboard will perature in 3/6 hours.
appear on the screen. Enter the text of your
Tap Back to return to the Local screen or Close
choice and tap Search for detailed information
to return to the SiriusXM Travel Link home
from the SiriusXM Travel Link database.
screen.
Local4
Information from the closest weather station will
be displayed and the following alternatives are
available:
4 This is the weather default unless another alternative has been selected. }}
* Option/accessory. 481
AUDIO, MEDIA AND INTERNET
482 * Option/accessory.
AUDIO, MEDIA AND INTERNET
* Option/accessory. 483
AUDIO, MEDIA AND INTERNET
|| the Sensus Navigation* supplement for additional 2. Tap a brand to display a list of service sta- SiriusXM Travel Link®* - Sports
information about using the navigation system. tions affiliated with that brand (BP, Exxon, This SiriusXM Travel Link service provides infor-
etc.). mation about sporting events, tournaments,
Recommended
Tap for a list of service stations near the vehicle, 3. Tap the name of a service station to display teams, leagues, etc.
displayed according to the price of regular gaso- more detailed information.
From the SiriusXM Travel Link home screen, to
line (unless another grade/type of fuel has been In addition to the Select fuel type button at the display sports information:
selected in Select fuel type) or of stations bottom of the screen, tap the Sort button to
offering the greatest number of available charg- – Tap the Sports button to display the main
arrange the list according to Nearest or
ing ports for electric vehicles/hybrids. The station sports screen.
Cheapest/Recommended. Tap Done to
offering the lowest price/most available charging return to the previous screen. A number of sports categories will be listed
ports will be displayed at the top of the list. Tap (Football, Baseball, Basketball, etc.)
the name of a service station to display more Related information
Tap a sport to select a league in that sport (NFL,
detailed information. • SiriusXM Travel Link®* (p. 480)
MLB, etc.) or a sport organization (PGA, LPGA,
Favorites • SiriusXM Travel Link®* - Notifications etc.).
Tap for a list of service stations that have been (p. 482)
The following is an example of the result of
stored as favorites. See also the heading • SiriusXM Travel Link®* - Sports (p. 484) tapping Baseball:
Favorites in the article "SiriusXM Travel Link" for
• SiriusXM Travel Link®* - Weather (p. 481) 1. MLB (Major League Baseball) will be dis-
information explaining how to create favorites.
Tap the name of a service station to display more played.
detailed information. 2. Tap MLB to display the two leagues in Major
In addition to the Select fuel type button at the League Baseball (American League or
bottom of the screen, tap the Edit button to National League).
delete individual stations from the list or tap 3. Tap one of the league names to display the
Delete to clear the list. Tap Done to return to divisions in the league.
the previous screen.
Brands
1. Tap Brands to display a list of service sta-
tion brands in the area.
484 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Related information
• SiriusXM Travel Link®* (p. 480)
• SiriusXM Travel Link®* - Notifications
(p. 482)
• SiriusXM Travel Link®* - Fuel (p. 483)
The media player is controlled
• SiriusXM Travel Link®* - Weather (p. 481)
from the center display. Several
functions can also be con-
trolled using voice commands
or the right-side steering wheel
keypad.
* Option/accessory. 485
AUDIO, MEDIA AND INTERNET
To start playback from an iPod, the iPod app Read the separate section on how to download
must be used (not USB). apps.
486 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Related information Controlling and changing media Changing track/song - tap the desired track in
• Handling the App menu in the instrument Media playback can be controlled using voice the center display, or press or below
panel (p. 105) commands, the steering wheel keypad or the the center display or on the right-side steering
• Radio (p. 468) center display. wheel keypad.
The media player can be con-
• Controlling and changing media (p. 487)
trolled using voice commands,
Rewinding/fast-forwarding - tap the time axis in
the center display and drag it sideways, or press
• Connecting a device via the USB port the right-side steering wheel
(p. 492) keypad or the center display. and hold or below the center display or
on the right-side steering wheel keypad.
• Connecting a device via Bluetooth® (p. 491)
Changing media source - select from among pre-
• Download apps (p. 466)
vious sources in the app, tap the desired app in
• Internet-connected vehicle* (p. 507) App view or use the right-side steering wheel
• Video (p. 490) keypad to select the app in the app menu .
• Apple® CarPlay®* (p. 493) Library - tap the button to play
• Android Auto* (p. 496) from the library.
• Voice control for radio and media (p. 150)
• Compatible file formats for media (p. 514)
}}
* Option/accessory. 487
AUDIO, MEDIA AND INTERNET
Related information
• Media player (p. 485)
• Media searches (p. 488)
• Sound settings (p. 464)
• Apps (p. 465)
• Gracenote® (p. 489) 1. Tap .
• Voice control for radio and media (p. 150) > Search view will displayed and the key-
board will open.
2. Enter a search word/phrase.
3. Tap Search.
> A search will be performed on connected
devices and the results will be displayed
by category.
Swipe the screen horizontally to display each cat-
egory separately.
488 * Option/accessory.
AUDIO, MEDIA AND INTERNET
* Option/accessory. 489
AUDIO, MEDIA AND INTERNET
490
AUDIO, MEDIA AND INTERNET
Video settings Streaming media via Bluetooth® Connecting a device via Bluetooth®
Some video playback settings can be adjusted, The vehicle's media player is equipped with Connect a Bluetooth® device to the vehicle to
e.g. language. Bluetooth and can play audio files from wirelessly play media and give the vehicle an
The following can be adjusted by opening Top Bluetooth-enabled external devices such as cel- Internet connection if it is available.
view and tapping Settings Video or with the lular phones and tablets.
video player in full-screen mode: Audio In order for the media player to be able to wire- Many cellular phones on the market currently
Language, Off and Subtitle Language. lessly play audio files from an external device, the offer wireless Bluetooth® technology, but not all
device must be connected to the vehicle via phones are fully compatible with the vehicle. For
Related information Bluetooth. additional information on compatibility, see
• Video (p. 490) support.volvocars.com.
Related information
The procedure for connecting a media device is
• Connecting a device via Bluetooth® (p. 491)
the same as for connecting a cellular phone to
• Connecting a phone to the car via Bluetooth the vehicle via Bluetooth®.
for the first time (p. 499)
• Playing media (p. 486) Related information
• Streaming media via Bluetooth® (p. 491)
• Compatible file formats for media (p. 514)
• Connecting a phone to the car via Bluetooth
for the first time (p. 499)
• Playing media (p. 486)
491
AUDIO, MEDIA AND INTERNET
Playing media via the USB port Connecting a device via the USB • Technical specifications for USB devices
External audio sources, such as an iPod® or port (p. 515)
MP3 player, can be connected to the audio sys- External audio sources, such as an iPod® or • Apple® CarPlay®* (p. 493)
tem via the vehicle's USB port. MP3 player, can be connected to the audio sys-
• Android Auto* (p. 496)
tem via any of the vehicle's USB ports.
Devices with rechargeable batteries can be
charged when they are connected via the USB If the vehicle has two USB ports, the phone must
port and the ignition is in mode I, II or the engine be connected to the port with the white frame to
is running. use Apple CarPlay* or Android Auto*.
The content on the external source can be read
faster if it only contains data of a compatible for-
mat. Video files can also be played via the USB
port.
Some MP3 players have their own file system
that the vehicle has support for.
Related information
• Connecting a device via the USB port
(p. 492)
• Playing media (p. 486)
• Video (p. 490)
USB ports (type A) in the tunnel console. Route the
• Ignition modes (p. 407) cable forward to help avoid pinching when the cover is
closed.
• Technical specifications for USB devices
(p. 515) Related information
• Apple® CarPlay®* (p. 493) • Playing media (p. 486)
• Android Auto* (p. 496) • Playing media via the USB port (p. 492)
• Media player (p. 485)
• Technical specifications for USB devices
(p. 515)
492 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Apple® CarPlay®* cuts off too soon, press and hold the 6 but- Using Apple® CarPlay®*
With CarPlay, you can listen to music, make ton on the steering wheel. To use CarPlay, the Siri voice control must be
phone calls, get driving instructions, send/ By using Apple CarPlay you acknowledge activated in your phone. The phone must also
receive messages and use Siri, all while remain- the following: Apple CarPlay is a service have an Internet connection via Wi-Fi or a mobile
ing focused on driving. provided by Apple Inc. under its terms and network.
CarPlay works with select conditions. Volvo Cars is thus not Connecting an iPhone and starting
Apple devices. If the car does responsible for Apple CarPlay or its
CarPlay
not already support CarPlay, features/applications. When using Apple
this can be retrofitted. Contact CarPlay, certain information from your car
(including its position) is transferred to your NOTE
a Volvo retailer to install
CarPlay. iPhone. In relation to Volvo Cars, you are CarPlay can only be used if Bluetooth is disa-
fully responsible for your and any others bled. A cell phone or media player connected
Information about supported apps and compati- person’s use of Apple CarPlay. to the vehicle via Bluetooth will therefore not
ble phones is available on the Apple website: be available when CarPlay is active. An alter-
www.apple.com/ios/carplay/. Using apps that are Related information native source must be used to provide an
not compatible with CarPlay could cause the con- • Using Apple® CarPlay®* (p. 493) Internet connection for the vehicle's apps.
nection between iPhone and the vehicle to be Use Wi-Fi or the vehicle's integrated modem.
• Settings for Apple® CarPlay®* (p. 494)
lost. Please note that Volvo is not responsible for
the content of CarPlay. • Voice control (p. 147)
1. Connect an iPhone to the USB port. If there
When using map navigation via CarPlay, guidance • Resetting center display settings (p. 137)
are two USB ports, use the one with the
will only be shown on the center display and not white frame.
in the instrument panel or head-up display.
2. Read the information in the pop-up window
CarPlay apps can be controlled from the center and then tap OK.
display, a phone or with the right-side steering
3. Tap Apple CarPlay in App view.
wheel keypad (for certain functions). The apps
can also be voice-controlled using Siri. Press and 4. Read the terms and conditions and then tap
hold the button on the steering wheel to Accept to connect.
start voice control with Siri. Press briefly to acti- > The CarPlay tile will open and compatible
vate the vehicle's own voice control system. If Siri apps will be displayed.
* Option/accessory. 493
AUDIO, MEDIA AND INTERNET
|| 5. Tap the desired app. 2. Proceed to Communication Apple Settings for Apple® CarPlay®*
> The app will start up. CarPlay. Settings for an Apple device connected through
Starting CarPlay 3. Uncheck the box for the Apple device that CarPlay8.
CarPlay can be started as follows after an iPhone should no longer start CarPlay automatically
when the USB cable is connected.
Automatic start
is connected.
1. Tap Settings in the Top view.
1. Connect an iPhone to the USB port. If there 4. Remove and then reinsert the Apple device
are two USB ports, use the one with the into the USB port. 2. Tap Communication Apple CarPlay and
white frame. select the desired setting:
5. Open the iPod app from App view.
> If the auto start setting is selected -
iPod to CarPlay
• Check the box - CarPlay will start auto-
the name of the phone will be displayed. matically when the USB cable is con-
1. Tap Apple CarPlay in App view. nected.
2. Tap the name of the phone - the CarPlay tile
2. Read the information in the pop-up window • Uncheck the box - CarPlay will not start
will open and compatible apps will be dis-
and then tap OK. automatically when the USB cable is con-
played.
3. Remove and then reinsert the Apple device nected.
3. If the CarPlay tile does not open, tap Apple
into the USB port. A maximum of 20 Apple devices can be stored in
CarPlay in App view.
> The Apple CarPlay tile will open and com- the list. When the list is full and a new device is
> The CarPlay tile will open and compatible
patible apps will be displayed7. connected, the oldest one will be deleted.
apps will be displayed.
Related information To delete the list, the settings must be rest in the
4. Tap the desired app.
center display (factory reset).
> The app will start up. • Connecting a device via the USB port
(p. 492) System Volumes
CarPlay will run in the background if another app
is started in the same tile. To display CarPlay in • Apple® CarPlay®* (p. 493) 1. Tap Settings in the Top view.
the tile, tap the CarPlay icon in App view. • Settings for Apple® CarPlay®* (p. 494) 2. Tap Sound System Volumes to change
Switching connection between CarPlay • Connecting the car to the Internet via a the settings for the following:
mobile device (Wi-Fi) (p. 509)
and iPod • Voice Control
CarPlay to iPod • Connect the car to the Internet via car
• Navi Voice Guidance
modem (SIM card) (p. 510)
1. Tap Settings in the Top view. • Phone Ringtone
• Voice control (p. 147)
7 Apple, CarPlay, iPhone and iPod are registered trademarks of Apple Inc.
494 * Option/accessory.
AUDIO, MEDIA AND INTERNET
* Option/accessory. 495
AUDIO, MEDIA AND INTERNET
496 * Option/accessory.
AUDIO, MEDIA AND INTERNET
From a previously connected Android device Settings for Android Auto* Related information
1. Connect the device to the USB port. Settings for phones initially connected with • Android Auto* (p. 496)
> If the auto start setting is selected - Android Auto. • Using Android Auto* (p. 496)
the name of the phone will be displayed.
Automatic start • Resetting center display settings (p. 137)
2. Tap the name of the phone - the 1. Tap Settings in the Top view.
Android Auto tile will open and compatible
apps will be displayed. 2. Tap Communication Android Auto and
select setting:
3. If the automatic start setting is not acti-
vated - open the Android Auto app from • Check the box - Android Auto will start
App view. automatically when the USB cable is con-
> The Android Auto tile will open and com- nected.
patible apps will be displayed. • Uncheck the box - Android Auto will not
4. Tap the desired app. start automatically when the USB cable is
connected.
> The app will start up.
A maximum of 20 Android devices can be stored
Android Auto will run in the background if in the list. When the list is full and a new device is
another app is started in the same tile. To display connected, the oldest one will be deleted.
Android Auto in the tile, tap the Android Auto
icon in App view. A factory reset must be performed to delete the
list.
Related information
• Android Auto* (p. 496) System Volumes
1. Tap Settings in the Top view.
• Settings for Android Auto* (p. 497)
• Connecting a device via the USB port 2. Tap Sound System Volumes to change
(p. 492) the settings for the following:
• Voice control (p. 147) • Voice Control
• Navi Voice Guidance
• Phone Ringtone
* Option/accessory. 497
AUDIO, MEDIA AND INTERNET
Related information
• Handling phone calls (p. 503)
• Managing the phone book (p. 505)
• Handling text messages (p. 504)
• Connecting a phone to the car via Bluetooth
for the first time (p. 499)
498 * Option/accessory.
AUDIO, MEDIA AND INTERNET
• Connecting a phone to the car via Bluetooth Connecting a phone to the car via 2. To connect the vehicle to the Internet via the
automatically (p. 501) Bluetooth for the first time phone's Bluetooth function, activate Internet
• Connecting a phone to the car via Bluetooth Pair a Bluetooth-enabled phone to the vehicle to sharing (tethering/personal hotspot) via
manually (p. 501) make calls, send/receive text messages and Bluetooth in the phone.
wirelessly play media from the vehicle, or con- 3. Open the phone tile.
• Disconnecting a Bluetooth-connected phone
(p. 502) nect the vehicle to the Internet.
Two Bluetooth devices can be connected at the • If no phone has been paired to the vehi-
• Switch between phones connected via Blue- same time, but in that case, only one will be used cle, tap Add phone.
tooth (p. 502) for wireless playback. The most recently paired • If a phone has been paired to the vehicle,
• Removing a Bluetooth-connected phone phone will be automatically connected to make tap Change . Tap Add phone in the
(p. 503) calls, send/receive text messages, play media or pop-up window.
• Phone settings (p. 506) use as an Internet connection. To change what > A list of available Bluetooth devices will be
the phone is used for when it is paired, go to displayed. The list will be updated as new
• Voice control (p. 147)
Bluetooth Devices settings. devices are discovered.
• Handling the App menu in the instrument
After the device has been connected/registered
panel (p. 105) 4. Tap the name of the phone you would like to
for the first time via Bluetooth, the device no connect.
• Sound settings (p. 464) longer needs to be visible/searchable. It just
• Connecting the car to the Internet via a needs to have Bluetooth activated. To connect 5. Make sure that the code displayed in the
mobile device (Bluetooth) (p. 509) the vehicle to the Internet using a phone, the vehicle matches the one in the phone. Con-
phone's Wi-Fi sharing function (personal hot- firm the code in both cases.
spot/tethering) must be activated. A maximum of 6. In the phone, accept or cancel the options
20 paired Bluetooth devices can be stored in the for selecting the phone's contacts and text
vehicle. messages.
There are two ways to pair a phone to the vehicle.
Searching for the phone from the vehicle or NOTE
searching for the vehicle from the phone.
• The message function must be activated
Option 1 - searching for the phone from in certain phones.
the vehicle • Not all cell phones are fully compatible
1. Make the phone discoverable/visible using and may not be able to display contacts
its Bluetooth function. and messages in the vehicle.
}}
499
AUDIO, MEDIA AND INTERNET
|| Option 2 - searching for the vehicle NOTE • Switch between phones connected via Blue-
from the phone tooth (p. 502)
• The message function must be activated
1. Open the phone tile.
in certain phones. • Removing a Bluetooth-connected phone
• If no phone has been paired to the vehi- (p. 503)
• Not all cell phones are fully compatible
cle, tap Add phone Make vehicle and may not be able to display contacts • Settings for Bluetooth devices (p. 507)
discoverable. and messages in the vehicle. • Connecting the car to the Internet via a
• If a phone has been paired to the vehicle, mobile device (Bluetooth) (p. 509)
tap Change . Tap Add phone
NOTE
Make vehicle discoverable in the pop-
up window. If the phone's operating system is being
updated, it is possible that the connection will
2. Activate Bluetooth in the phone. be interrupted. Delete the phone from the car
3. To connect the vehicle to the Internet via the and reconnect.
phone's Bluetooth function, activate Internet
sharing (tethering/personal hotspot) via Compatible phones
Bluetooth in the phone. Many cellular phones on the market currently
4. Search in the phone for Bluetooth devices. offer wireless Bluetooth technology, but not all
> A list of available Bluetooth devices will be phones are fully compatible with the vehicle. For
displayed. additional information on compatibility, see
support.volvocars.com.
5. Select the vehicle's name from the list of
devices in the phone. Related information
6. A pop-up window for the connection is • Phone (p. 498)
shown in the car. Confirm the connection. • Connecting a phone to the car via Bluetooth
automatically (p. 501)
7. Make sure that the code displayed in the
vehicle matches the one in the external • Connecting a phone to the car via Bluetooth
device. Confirm the code in both cases. manually (p. 501)
8. In the phone, accept or cancel the options • Disconnecting a Bluetooth-connected phone
for selecting the phone's contacts and text (p. 502)
messages.
500
AUDIO, MEDIA AND INTERNET
Connecting a phone to the car via • Connecting the car to the Internet via a Connecting a phone to the car via
Bluetooth automatically mobile device (Bluetooth) (p. 509) Bluetooth manually
A phone can be automatically connected to the • Ignition modes (p. 407) A phone can be manually connected to the vehi-
vehicle via Bluetooth. The phone must have first cle via Bluetooth. The phone must have first
been paired with the vehicle. been paired with the vehicle.
Only the two most recently connected phones 1. Activate Bluetooth in the phone.
can be connected automatically.
To simultaneously connect the vehicle to the
1. Activate Bluetooth in the phone before turn- Internet, the phone's personal hotspot must
ing the vehicle's ignition to mode I. also be activated.
To simultaneously connect the vehicle to the 2. Open the phone tile.
Internet, the phone's personal hotspot must > A list of available phones will be displayed.
also be activated.
3. Tap the name of the phone you would like to
2. Turn the ignition to I or higher. connect.
> The phone will be connected. > The phone will be connected.
Related information Related information
• Phone (p. 498) • Phone (p. 498)
• Connecting a phone to the car via Bluetooth • Connecting a phone to the car via Bluetooth
for the first time (p. 499) for the first time (p. 499)
• Connecting a phone to the car via Bluetooth • Connecting a phone to the car via Bluetooth
manually (p. 501) automatically (p. 501)
• Disconnecting a Bluetooth-connected phone • Disconnecting a Bluetooth-connected phone
(p. 502) (p. 502)
• Switch between phones connected via Blue- • Switch between phones connected via Blue-
tooth (p. 502) tooth (p. 502)
• Removing a Bluetooth-connected phone • Removing a Bluetooth-connected phone
(p. 503) (p. 503)
• Settings for Bluetooth devices (p. 507)
}}
501
AUDIO, MEDIA AND INTERNET
• Settings for Bluetooth devices (p. 507) Disconnecting a Bluetooth- Switch between phones connected
• Connecting the car to the Internet via a connected phone via Bluetooth
mobile device (Bluetooth) (p. 509) Disconnect a Bluetooth-connected phone from It is possible to switch between Bluetooth-con-
the vehicle by deactivating Bluetooth in the nected phones.
phone. 1. Open the phone tile.
When the phone is out of range of the vehicle, it
will be automatically disconnected. If a call is in 2. Tap Change or pull down Top view and
progress when the phone is disconnected from tap Settings Communication
the vehicle, the call will be transferred from the Bluetooth Devices Add device.
vehicle's speakers and microphone to the cellular > A list of available Bluetooth devices will be
phone. displayed.
Related information 3. Tap the name of the phone you would like to
• Phone (p. 498) connect.
• Phone settings (p. 506) Related information
• Switch between phones connected via Blue- • Phone (p. 498)
tooth (p. 502)
• Connecting a phone to the car via Bluetooth
• Removing a Bluetooth-connected phone for the first time (p. 499)
(p. 503)
• Settings for Bluetooth devices (p. 507)
• Settings for Bluetooth devices (p. 507)
• Disconnecting a Bluetooth-connected phone
(p. 502)
• Removing a Bluetooth-connected phone
(p. 503)
502
AUDIO, MEDIA AND INTERNET
Removing a Bluetooth-connected Handling phone calls Calls can also be made from the list of recent
phone Handling phone calls in the vehicle for a calls using the app menu, which can be opened
Phones in the list of registered Bluetooth devi- Bluetooth-connected cellular phone. using the button on the right-side steering
ces can be removed. wheel keypad.
1. Tap Settings in the Top view. Making multiple calls
2. Tap Communication Bluetooth While the call is in progress:
Devices. 1. Tap Add call.
> A list of registered Bluetooth devices is
2. Select from the list of recent calls, favorites
displayed.
or contacts.
3. Tap the name of the phone you would like to
3. Tap an item/row in the list of recent calls or
remove.
for the contact in the phone book.
4. Tap Remove device and confirm.
4. Tap Swap call to switch between calls.
> The phone is no longer registered in the
vehicle. 5. Tap to end the current call.
Generic illustration.
Related information Group (conference) calls
• Phone (p. 498) Making calls While multiple calls are in progress:
1. Open the phone tile.
• Connecting a phone to the car via Bluetooth 1. Tap Join calls to merge ongoing calls.
for the first time (p. 499) 2. Initiate a call by selecting the phone number
from the recent calls list, entering the num- 2. Tap to end the call.
• Disconnecting a Bluetooth-connected phone
ber on the keypad or selecting a number
(p. 502) Incoming calls
from the phone book (list of contacts). You Incoming phone calls will be shown on the instru-
• Switch between phones connected via Blue- can search or scroll to find a contact in the
tooth (p. 502) ment panel and in the center display. Manage the
phone book. Tap in the phone book to calls using the right-side steering wheel keypad
• Settings for Bluetooth devices (p. 507) add a contact to Favorites. or the center display.
3. Tap . 1. Tap Answer/Reject.
}}
503
AUDIO, MEDIA AND INTERNET
|| Incoming calls while another call is in Handling text messages Reading text messages in the center display
progress A Bluetooth-connected cellular phone's text Tap the icon to have the message read
1. Tap Answer/Reject. messages can be handled in the vehicle. aloud.
Text message functionality needs to be activated
2. Tap to end the call. in certain phones. Not all phones are fully com-
patible and therefore cannot display contacts and Sending text messages in the center
Privacy
messages in the vehicle. For additional informa- display10
– While a call is in progress, tap Privacy and
select setting: tion on compatibility, see support.volvocars.com. 1. It is possible to reply to text messages or
create a new message.
• Switch to mobile phone - the hands- Handling text messages in the center
free function will be disabled and the call display • To reply to a text message - tap the name
of the contact who sent the message and
will proceed on the cellular phone. Text messages are only shown in the center dis-
play if the relevant setting is made. then tap Answer.
• Driver focused - the microphone in the
ceiling liner on the passenger side will be Tap Messages in App view to
• To create a new message - tap Create
muted and the call will proceed using the new. Select a contact or enter a phone
handle text messages in the
vehicle's hands-free function. number.
center display.
2. Write the message.
Related information
• Phone (p. 498) 3. Tap Send.
• Connecting a phone to the car via Bluetooth Handling test messages in the
for the first time (p. 499) instrument panel
NOTE
• Voice control for cellular phones (p. 149) Text messages are only shown in the instrument
When the vehicle is moving: panel if the relevant setting is made.
• Handling the App menu in the instrument
panel (p. 105) • Only one row of the message will be dis-
Reading new text messages in the
played. Tap Read out to have the entire
• Entering characters, letters and words by
message read aloud.
instrument panel
hand in the center display (p. 131) – To have the message read aloud, select
• The center display's keyboard cannot be Read out using the steering wheel keypad.
• Managing the phone book (p. 505)
used.
• Handling text messages (p. 504)
• Sound settings (p. 464)
10 Only certain phones can send messages via the vehicle. For additional information on compatibility, see support.volvocars.com.
504
AUDIO, MEDIA AND INTERNET
Dictating replies in the instrument panel Text message settings Managing the phone book
After the test message has been read aloud, it is Settings for handling text messages received Contacts in a Bluetooth-connected cellular
possible to answer briefly with dictation if the through a connected phone can be personal- phone can be managed in the vehicle.
vehicle has an Internet connection. ized.
– Tap Answer using the steering wheel key- 1. Tap Settings in the Top view.
pad. A dictation dialog will start. 2. Tap Communication Text Messages
Message notification and select settings:
Notifications can be activated and deactivated in • Notification in center display - display
the text message settings. text message notifications in the center
display's status bar.
Related information
• Phone (p. 498) • Notification in driver display - displays
notifications in the driver's display and
• Text message settings (p. 505) incoming messages can be managed
• Phone settings (p. 506) using the steering wheel's right-hand key-
• Internet-connected vehicle* (p. 507) pad. Scroll by letter or to find contacts. Only
• Voice control for cellular phones (p. 149) • Text message tone - select tone for letters matching existing contacts in the
incoming text messages. phone book will be shown.
• Entering characters, letters and words by
hand in the center display (p. 131) Related information Search contacts - tap to search by
phone number or name in the phone book.
• Connecting a phone to the car via Bluetooth • Phone (p. 498)
for the first time (p. 499) • Connecting a phone to the car via Bluetooth Favorites - tap to add/remove a con-
for the first time (p. 499) tact from the list of favorites.
• Handling text messages (p. 504)
NOTE
• Phone settings (p. 506)
Only contacts from an active Bluetooth-con-
nected phone are shown in the center display.
Up to 3000 contacts can be displayed.
}}
* Option/accessory. 505
AUDIO, MEDIA AND INTERNET
Related information
• Phone (p. 498)
• Text message settings (p. 505)
• Settings for Bluetooth devices (p. 507)
506 * Option/accessory.
AUDIO, MEDIA AND INTERNET
}}
* Option/accessory. 507
AUDIO, MEDIA AND INTERNET
|| When the vehicle is connected to the Internet, NOTE • Sharing Internet from the vehicle via Wi-Fi
other devices may share the vehicle's Internet hotspot (tethering) (p. 511)
connection (Wi-Fi hotspot)11. When using Apple CarPlay, it is only possible
to connect the vehicle to the Internet using • Deleting Wi-Fi networks (p. 513)
The connection status is shown by a symbol in Wi-Fi or the vehicle's modem. • Wi-Fi technology and security (p. 513)
the center display's status bar.
• Volvo ID (p. 26)
• Terms of use and data sharing (p. 514)
NOTE
When using Android Auto, it is possible to
connect the vehicle to the Internet using
Wi-Fi, Bluetooth or the vehicle's modem.
Related information
• Symbols in the center display status bar
NOTE (p. 126)
Data (data traffic) is transfered when using • Connecting the car to the Internet via a
the internet, which can incur additional costs. mobile device (Bluetooth) (p. 509)
Activating data roaming can cause additional • Connecting the car to the Internet via a
charges. mobile device (Wi-Fi) (p. 509)
Contact your network operator about data • Connect the car to the Internet via car
traffic costs. modem (SIM card) (p. 510)
• Apps (p. 465)
• No or poor Internet connection (p. 512)
11 This is not possible when the vehicle is connected to another Wi-Fi hotspot.
508
AUDIO, MEDIA AND INTERNET
Connecting the car to the Internet Related information Connecting the car to the Internet
via a mobile device (Bluetooth) • Internet-connected vehicle* (p. 507) via a mobile device (Wi-Fi)
Establish an Internet connection using Bluetooth • Connect the car to the Internet via car Establish an Internet connection via Wi-Fi tether-
and tethering from a phone and get access to modem (SIM card) (p. 510) ing from a phone and get access to multiple
multiple connected services in your vehicle. connected services in your vehicle.
The phone and the network service provider must
• Connecting a phone to the car via Bluetooth
The phone and the network service provider must
for the first time (p. 499)
support Internet sharing (tethering) and the sub- support Internet sharing (tethering) and the sub-
scription must include data transfer. • Connecting the car to the Internet via a scription must include data transfer.
mobile device (Wi-Fi) (p. 509)
1. To connect the vehicle to the Internet via a
Bluetooth-connected phone, the phone must • Apple® CarPlay®* (p. 493)
first be paired with the vehicle via Bluetooth. • No or poor Internet connection (p. 512)
Ensure that the personal hotspot (portable/
• Settings for Bluetooth devices (p. 507)
personal hotspot) is activated in your phone.
2. If the phone has been connected via Blue-
tooth previously, tap Settings in the center 1. Activate Internet sharing (personal hotspot)
display's Top view. in the phone.
3. In the center display: Tap Communication 2. Tap Settings in the Top view.
Bluetooth Devices.
3. Proceed to Communication Wi-Fi.
4. Mark the window for Bluetooth Internet 4. Activate/deactivate by tapping to check/
connection under the heading Internet uncheck the Wi-Fi box.
connection.
> Your vehicle is now connected to the 5. Tap the name of the network you would like
Internet via your Bluetooth-connected to connect.
phone. 6. Enter the network password.
7. If a different connection was used previously,
NOTE confirm the connection change.
When using Apple CarPlay, it is only possible > The vehicle will connect to the network.
to connect the vehicle to the Internet using
Please note that certain cellular phones will disa-
Wi-Fi or the vehicle's modem.
ble Internet sharing (tethering) when the connec-
}}
* Option/accessory. 509
AUDIO, MEDIA AND INTERNET
|| tion to the vehicle has been broken, e.g. when the Connect the car to the Internet via 5. If a different connection was used previously,
phone has been removed from the vehicle. The car modem (SIM card) confirm the connection change.
phone's tethering function will then need to be For vehicles equipped with Volvo On Call, it is 6. Enter the SIM card's PIN code.
reactivated the next time the phone's hotspot is possible to establish an Internet connection via
used to connect to the Internet. > The vehicle will connect to the network.
the vehicle modem and a personal SIM card (P-
When a phone is connected to the vehicle, it will SIM). Related information
be saved for future use. When the maximum When the vehicle is connected using the inte- • Internet-connected vehicle* (p. 507)
number of 50 connected phones has been grated modem, the Volvo On Call services will
use this connection. • No or poor Internet connection (p. 512)
reached, the first will be deleted. To display a list
of saved networks or to manually delete saved • Vehicle modem settings (p. 511)
1.
networks, tap Settings Communication
Wi-Fi Saved networks.
Technical and security requirements for Wi-Fi
connection are described in a separate section.
Related information
• Internet-connected vehicle* (p. 507)
• Deleting Wi-Fi networks (p. 513)
• No or poor Internet connection (p. 512)
• Wi-Fi technology and security (p. 513)
510 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Vehicle modem settings • Send request code - used to e.g. download Sharing Internet from the vehicle via
Your vehicle is equipped with a modem that can or check the balance remaining on a prepaid Wi-Fi hotspot (tethering)
be used to connect the vehicle to the Internet. It phone card. This function is specific to your When the vehicle is connected to the Internet,
is also possible to share this Internet connection service provider. other devices may share the vehicle's Internet
over Wi-Fi. connection12.
Related information
1. Tap Settings in the Top view. • Connect the car to the Internet via car
modem (SIM card) (p. 510)
2. Tap Communication Vehicle Modem
Internet and select settings: • No or poor Internet connection (p. 512)
511
AUDIO, MEDIA AND INTERNET
|| 2. Tap Communication Vehicle Wi-Fi Tap Connected devices to see a list of cur- No or poor Internet connection
Hotspot. rently connected devices. Factors affecting the Internet connection.
3. Tap Network name to assign a name to the Related information The amount of data transmitted depends on the
hotspot. • Symbols in the center display status bar services or apps currently in use in the vehicle.
4. Tap Password and create a password. This (p. 126) Streaming music, for example, involves the trans-
password can then be used to connect other • Internet-connected vehicle* (p. 507) mission of a large amount of data, and this
devices to this hotspot. requires a good connection and a strong signal.
• No or poor Internet connection (p. 512)
5. Tap Frequency band and select a fre- Phone to vehicle
quency for the hotspot to use to transmit Internet connection speed may vary depending
data. Please note that selecting a frequency on the location of the cellular phone in the vehi-
is not possible on all markets. cle. Move the phone closer to the center display
6. Activate/deactivate by tapping to check/ to increase signal strength. Make sure that noth-
uncheck the Vehicle Wi-Fi Hotspot box. ing is between the phone and center display that
could be blocking the signal.
7. If Wi-Fi was previously used to connect to
the Internet, confirm the change of connec- Phone to network operator
tions. The speed of the mobile network varies depend-
> It is now possible for external devices to ing on the coverage in the vehicle's current loca-
connect to the vehicle's Wi-Fi hotspot. tion. Coverage may be poorer in e.g. tunnels,
mountainous areas, deep valleys or indoors. Con-
nection speed is also dependent on the subscrip-
NOTE
tion you have with your service provider.
Activation of Wi-Fi hotspot can cause addi-
tional charges from your network operator. NOTE
Contact your network operator about data If you experience any problems with data traf-
traffic costs. fic, contact your network service provider.
12 This does not apply when the vehicle is connected to the Internet via Wi-Fi.
512 * Option/accessory.
AUDIO, MEDIA AND INTERNET
Restarting the phone Deleting Wi-Fi networks Wi-Fi technology and security
If you experience any Internet connection prob- Networks that are not needed can be deleted. Networks must meet certain criteria in order for
lems, it may help to restart your phone. the vehicle to connect.
1. Tap Settings in the Top view.
Related information It is possible to connect to the following types of
• Internet-connected vehicle* (p. 507) 2. Proceed to Communication Wi-Fi networks:
Saved networks.
• Wi-Fi technology and security (p. 513)
• Frequency - 2.4 or 5 GHz13.
3. Tap Forget to delete the network.
• Standards - 802.11 a/b/g/n.
4. Confirm the selection.
• Security type - WPA2-AES-CCMP.
> The vehicle will no longer connect to the
deleted network. The vehicle's Wi-Fi system is designed to handle
Wi-Fi devices inside the vehicle.
Deleting all networks Performance may be impaired if multiple devices
All networks can be deleted at once by perform- are using a frequency at the same time.
ing a factory reset. Please note that all user data
and system settings will be restored to original Related information
default factory settings. • Internet-connected vehicle* (p. 507)
Related information
• Internet-connected vehicle* (p. 507)
• No or poor Internet connection (p. 512)
• Resetting center display settings (p. 137)
• Connecting the car to the Internet via a
mobile device (Wi-Fi) (p. 509)
* Option/accessory. 513
AUDIO, MEDIA AND INTERNET
Terms of use and data sharing Activating and deactivating data Compatible file formats for media
The first time certain services and apps are sharing In order to play media, the following file formats
started, a pop-up window with the heading Data sharing for relevant services and apps can must be used.
Terms and conditions and Data sharing may be set via the Settings menu in the center dis-
open. play. Audio files
The aim is to inform the user about Volvo's terms 1. Tap Settings in the Top view in the center For- File extension Codec
of use and data sharing policy. By accepting data display. mat
sharing, the user accepts that certain information
will be sent from the vehicle. This is required for 2. Tap System Privacy and data. MP3 .mp3 MPEG1 Layer III,
certain services and apps to work with full func- 3. Select Data sharing to enable or disable MPEG2 Layer III,
tionality. data sharing. MP3 Pro (mp3
compatible),
Data sharing can be set from the center display's 4. When data sharing is enabled, settings for MP3 HD (mp3
Settings menu. individual services and apps in the list below compatible)
can be changed.
Related information AAC .m4a, .m4b, .aac AAC LC (MPEG-4
• Activating and deactivating data sharing When data sharing is disabled, the previous set- part III Audio),
(p. 514) tings for individual services and apps are saved HE-AAC (aacPlus
and restored when data sharing is enabled again. v1/v2)
Related information WMA .wma WMA8/9,
• Terms of use and data sharing (p. 514) WMA9/10 Pro
WAV .wav LPCM
FLAC .flac FLAC
Video files
Format File extension
MP4 .mp4, m4v
MPEG-PS .mpg, .mp2, .mpeg, .m1v
514
AUDIO, MEDIA AND INTERNET
Format File extension File extension .divx, .avi Technical specifications for USB
devices
AVI .avi Max. file size 4 GB For the contents of USB devices to be read, the
AVI (DivX) .avi, divx Audio codec MP3, AC3 following specifications must be met.
Any folder structures will not be shown in the
ASF .asf, .wmv Subtitles XSUB center display during playback.
MKV .mkv Special func- Multiple subtitles, multiple
tions audio, resume play Max. number
Subtitles Reference Meets all requirements of Files 15 000
Format File extension the DivX Home Theater Folders 1 000
profile. Visit divx.com for
SubViewer .sub more information and soft- Folder levels 8
SubRip .srt ware tools to convert your
files into DivX Home Playlists 100
SSA .ssa Theater video. Tracks in a playlist 1 000
DivX® Related information Subfolders No limit
DivX-certified devices have been tested for high-
• Media player (p. 485)
quality DivX (.divx, .avi) video playback. When you Technical specifications for the USB-A
see the DivX logo, you have the freedom to play • Video (p. 490)
connector
your favorite DivX videos. • Playing DivX® (p. 490) • Type A port
515
AUDIO, MEDIA AND INTERNET
Related information
• Apps (p. 465)
516
AUDIO, MEDIA AND INTERNET
License agreement for audio and Dirac Unison® DivX®, DivX Certified® and associated logos are
media trademarks of DivX, LLC and are used under
A license is an agreement on the right to con- license.
duct a certain activity or the right to use some- This DivX Certified® device can play DivX® Home
one else's right according to terms and condi- Theater Home Theater video files up to 576p
tions specified in the agreement. The following (including .avi, .divx). Download free software at
texts are Volvo's agreements with manufactur- www.divx.com to create, play and stream digital
ers/developers. video.
Bowers & Wilkins ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
Dirac Unison co-optimizes the loudspeakers in play purchased DivX Video-on-Demand (VOD)
frequency, time and space for the best possible movies. To obtain your registration code, locate
bass integration and clarity. It enables a faithful the DivX VOD section in your device setup menu.
reproduction of the acoustic characteristics of Go to vod.divx.com for more information on com-
specific performance venues. Using advanced pleting the registration process.
algorithms, Dirac Unison controls all loudspeak-
ers digitally based on acoustic high-precision Patent number
measurements. Like a conductor of an orchestra, Covered by one or more of the following patents
it guarantees that the loudspeakers perform in in the US: 7,295,673; 7,460,668; 7,515,710;
Bowers & Wilkins and B&W are trademarks of perfect unison. 8,656,183; 8,731,369; RE45,052.
the B&W Group Ltd. Nautilus is a trademark of
B&W Group Ltd. Kevlar is a registered trademark DivX® Gracenote®
of DuPont.
}}
517
AUDIO, MEDIA AND INTERNET
|| Portions of the content are copyright © of these restrictions. If your license terminates, you additional data types or categories that Grace-
Gracenote or its providers. agree to cease any and all use of the Gracenote note may provide in the future and is free to dis-
Data, the Gracenote Software, and Gracenote continue its services at any time.
Gracenote, the Gracenote logo and logotype,
Servers. Gracenote reserves all rights in all
"Powered by Gracenote" and Gracenote MusicID GRACENOTE DISCLAIMS ALL WARRANTIES
Gracenote Data, all Gracenote Software, and all
are either registered trademarks of Gracenote, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
Gracenote Servers, including all ownership rights.
Inc. in the United States and/or other countries. LIMITED TO, IMPLIED WARRANTIES OF MER-
Under no circumstances will Gracenote become
CHANTABILITY, FITNESS FOR A PARTICULAR
Gracenote® End User License Agreement liable for any payment to you for any information
PURPOSE, TITLE, AND NON-INFRINGEMENT.
This application or device contains software from that you provide. You agree that Gracenote, Inc.
GRACENOTE DOES NOT WARRANT THE
Gracenote, Inc. in Emeryville, California, United may enforce its rights under this Agreement
RESULTS THAT WILL BE OBTAINED BY YOUR
States ("Gracenote"). The software from Grace- against you directly in its own name.
USE OF THE GRACENOTE SOFTWARE OR
note (the “Gracenote Software”) enables this The Gracenote service uses a unique identifier to ANY GRACENOTE SERVER. IN NO CASE WILL
application to perform disc and/or file identifica- track queries for statistical purposes. The pur- GRACENOTE BE LIABLE FOR ANY CONSE-
tion and obtain music-related information, includ- pose of a randomly assigned numeric identifier is QUENTIAL OR INCIDENTAL DAMAGES OR
ing name, artist, track, and title information to allow the Gracenote service to count queries FOR ANY LOST PROFITS OR LOST REVENUES.
(“Gracenote Data”) from online servers or embed- without knowing anything about who you are. For
ded databases (collectively “Gracenote Servers”) © Gracenote, Inc. 2009
more information, see the web page for the
and to perform other functions. You may use Gracenote Privacy Policy for the Gracenote serv-
Gracenote Data only by means of the intended
Sensus software
ice.
End-User functions of this application or device. This software uses parts of sources from clib2
The Gracenote Software and each item of Grace- and Prex Embedded Real-time OS - Source
You agree that you will use Gracenote Data, the note Data are licensed to you “AS IS.” Gracenote (Copyright (c) 1982, 1986, 1991, 1993, 1994),
Gracenote Software, and Gracenote Servers for makes no representations or warranties, express and Quercus Robusta (Copyright (c) 1990,
your own personal non-commercial use only. You or implied, regarding the accuracy of any Grace- 1993), The Regents of the University of
agree not to assign, copy, transfer or transmit the note Data from in the Gracenote Servers. Grace- California. All or some portions are derived from
Gracenote Software or any Gracenote Data to note reserves the right to delete data from the material licensed to the University of California by
any third party. YOU AGREE NOT TO USE OR Gracenote Servers or to change data categories American Telephone and Telegraph Co. or Unix
EXPLOIT GRACENOTE DATA, THE GRACE- for any cause that Gracenote deems sufficient. System Laboratories, Inc. and are reproduced
NOTE SOFTWARE, OR GRACENOTE SERVERS, No warranty is made that the Gracenote Software herein with the permission of UNIX System
EXCEPT AS EXPRESSLY PERMITTED HEREIN. or Gracenote Servers are error-free or that func- Laboratories, Inc. Redistribution and use in
You agree that your non-exclusive license to use tioning of Gracenote Software or Gracenote source and binary forms, with or without
the Gracenote Data, the Gracenote Software, and Servers will be uninterrupted. Gracenote is not modification, are permitted provided that the
Gracenote Servers will terminate if you violate obligated to provide you with new enhanced or following conditions are met: Redistributions of
518
AUDIO, MEDIA AND INTERNET
source code must retain the above copyright This software is based in part on the work of the SILICON GRAPHICS, INC. BE LIABLE FOR ANY
notice, this list of conditions and the following Independent JPEG Group. CLAIM, DAMAGES OR OTHER LIABILITY,
disclaimer. Redistributions in binary form must WHETHER IN AN ACTION OF CONTRACT,
This software uses parts of sources from
reproduce the above copyright notice, this list of TORT OR OTHERWISE, ARISING FROM, OUT
"libtess". The Original Code is: OpenGL Sample
conditions and the following disclaimer in the OF OR IN CONNECTION WITH THE SOFTWARE
Implementation, Version 1.2.1, released January
documentation and/or other materials provided OR THE USE OR OTHER DEALINGS IN THE
26, 2000, developed by Silicon Graphics, Inc. The
with the distribution. Neither the name of the SOFTWARE. Except as contained in this notice,
Original Code is Copyright (c) 1991-2000 Silicon
<ORGANIZATION> nor the names of its the name of Silicon Graphics, Inc. shall not be
Graphics, Inc. Copyright in any portions created
contributors may be used to endorse or promote used in advertising or otherwise to promote the
by third parties is as indicated elsewhere herein.
products derived from this software without sale, use or other dealings in this Software
All Rights Reserved. Copyright (C) [1991-2000]
specific prior written permission. THIS without prior written authorization from Silicon
Silicon Graphics, Inc. All Rights Reserved.
SOFTWARE IS PROVIDED BY THE COPYRIGHT Graphics, Inc.
Permission is hereby granted, free of charge, to
HOLDERS AND CONTRIBUTORS "AS IS" AND
any person obtaining a copy of this software and This software is based in parts on the work of the
ANY EXPRESS OR IMPLIED WARRANTIES,
associated documentation files (the "Software"), FreeType Team.
INCLUDING, BUT NOT LIMITED TO, THE
to deal in the Software without restriction,
IMPLIED WARRANTIES OF MERCHANTABILITY This software uses parts of SSLeay Library:
including without limitation the rights to use,
AND FITNESS FOR A PARTICULAR PURPOSE Copyright (C) 1995-1998 Eric Young
copy, modify, merge, publish, distribute,
ARE DISCLAIMED. IN NO EVENT SHALL THE (eay@cryptsoft.com). All rights reserved
sublicense, and/or sell copies of the Software,
COPYRIGHT OWNER OR CONTRIBUTORS BE
and to permit persons to whom the Software is Linux software
LIABLE FOR ANY DIRECT, INDIRECT,
furnished to do so, subject to the following
INCIDENTAL, SPECIAL, EXEMPLARY, OR This product contains software licensed under
conditions: The above copyright notice including
CONSEQUENTIAL DAMAGES (INCLUDING, GNU General Public License (GPL) or GNU
the dates of first publication and either this
BUT NOT LIMITED TO, PROCUREMENT OF Lesser General Public License (LGPL), etc.
permission notice or a reference to http://
SUBSTITUTE GOODS OR SERVICES; LOSS OF
oss.sgi.com/projects/FreeB/ shall be included in You have the right of acquisition, modification,
USE, DATA, OR PROFITS; OR BUSINESS
all copies or substantial portions of the Software. and distribution of the source code of the GPL/
INTERRUPTION) HOWEVER CAUSED AND ON
THE SOFTWARE IS PROVIDED "AS IS", LGPL software.
ANY THEORY OF LIABILITY, WHETHER IN
WITHOUT WARRANTY OF ANY KIND,
CONTRACT, STRICT LIABILITY, OR TORT You may download Source Code from the
EXPRESS OR IMPLIED, INCLUDING BUT NOT
(INCLUDING NEGLIGENCE OR OTHERWISE) following website at no charge: http://
LIMITED TO THE WARRANTIES OF
ARISING IN ANY WAY OUT OF THE USE OF www.embedded-carmultimedia.jp/linux/oss/
MERCHANTABILITY, FITNESS FOR A
THIS SOFTWARE, EVEN IF ADVISED OF THE download/TVM_8351_013
PARTICULAR PURPOSE AND
POSSIBILITY OF SUCH DAMAGE.
NONINFRINGEMENT. IN NO EVENT SHALL
}}
519
AUDIO, MEDIA AND INTERNET
|| The website provides the Source Code "As Is" PARTICULAR PURPOSE ARE DISCLAIMED. IN the above copyright notice(s) and this permission
and without warranty of any kind. NO EVENT SHALL NTT BE LIABLE FOR ANY notice appear with all copies of the Data Files or
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, Software, (b) both the above copyright notice(s)
By downloading Source Code, you expressly
EXEMPLARY, OR CONSEQUENTIAL DAMAGES and this permission notice appear in associated
assume all risk and liability associated with
(INCLUDING, BUT NOT LIMITED TO, documentation, and (c) there is clear notice in
downloading and using the Source Code and
PROCUREMENT OF SUBSTITUTE GOODS OR each modified Data File or in the Software as
complying with the user agreements that
SERVICES; LOSS OF USE, DATA, OR PROFITS; well as in the documentation associated with the
accompany each Source Code.
OR BUSINESS INTERRUPTION) HOWEVER Data File(s) or Software that the data or software
Please note that we cannot respond to any CAUSED AND ON ANY THEORY OF LIABILITY, has been modified.
inquiries regarding the source code. WHETHER IN CONTRACT, STRICT LIABILITY,
THE DATA FILES AND SOFTWARE ARE
OR TORT (INCLUDING NEGLIGENCE OR
camellia:1.2.0 PROVIDED "AS IS", WITHOUT WARRANTY OF
OTHERWISE) ARISING IN ANY WAY OUT OF
Copyright (c) 2006, 2007 ANY KIND, EXPRESS OR IMPLIED, INCLUDING
THE USE OF THIS SOFTWARE, EVEN IF
BUT NOT LIMITED TO THE WARRANTIES OF
NTT (Nippon Telegraph and Telephone ADVISED OF THE POSSIBILITY OF SUCH
MERCHANTABILITY, FITNESS FOR A
Corporation). All rights reserved. DAMAGE.
PARTICULAR PURPOSE AND
Redistribution and use in source and binary Unicode: 5.1.0 NONINFRINGEMENT OF THIRD PARTY
forms, with or without modification, are permitted COPYRIGHT AND PERMISSION NOTICE RIGHTS. IN NO EVENT SHALL THE
provided that the following conditions are met: COPYRIGHT HOLDER OR HOLDERS
Copyright c 1991-2013 Unicode, Inc. All rights INCLUDED IN THIS NOTICE BE LIABLE FOR
1. Redistributions of source code must retain reserved. Distributed under the Terms of Use in ANY CLAIM, OR ANY SPECIAL INDIRECT OR
the above copyright notice, this list of http://www.unicode.org/copyright.html. CONSEQUENTIAL DAMAGES, OR ANY
conditions and the following disclaimer as
Permission is hereby granted, free of charge, to DAMAGES WHATSOEVER RESULTING FROM
the first lines of this file unmodified.
any person obtaining a copy of the Unicode data LOSS OF USE, DATA OR PROFITS, WHETHER
2. Redistributions in binary form must files and any associated documentation (the IN AN ACTION OF CONTRACT, NEGLIGENCE
reproduce the above copyright notice, this list "Data Files") or Unicode software and any OR OTHER TORTIOUS ACTION, ARISING OUT
of conditions and the following disclaimer in associated documentation (the "Software") to OF OR IN CONNECTION WITH THE USE OR
the documentation and/or other materials deal in the Data Files or Software without PERFORMANCE OF THE DATA FILES OR
provided with the distribution. restriction, including without limitation the rights SOFTWARE.
THIS SOFTWARE IS PROVIDED BY NTT ``AS to use, copy, modify, merge, publish, distribute, Except as contained in this notice, the name of a
IS'' AND ANY EXPRESS OR IMPLIED and/or sell copies of the Data Files or Software, copyright holder shall not be used in advertising
WARRANTIES, INCLUDING, BUT NOT LIMITED and to permit persons to whom the Data Files or or otherwise to promote the sale, use or other
TO, THE IMPLIED WARRANTIES OF Software are furnished to do so, provided that (a)
MERCHANTABILITY AND FITNESS FOR A
520
AUDIO, MEDIA AND INTERNET
}}
521
AUDIO, MEDIA AND INTERNET
|| Country/
Area
Brazil:
Este equipamento opera em caráter secundário isto e, náo tem direito a protecão contra interferéncia prejudicial, mesmo tipo, e não pode
causar interferéncia a sistemas operando em caráter primário.
Para consultas, visite: www.anatel.gov.br
EU:
Manufacturer: Mitsubishi Electric Corporation Sanda Works 2-3-33, Miwa, Sanda-city. Hyogo, 669-1513, Japan
Mitsubishi Electric Corporation hereby declares that this type of radio equipment [Audio Navigation Unit] conforms with directive 2014/53/EU.
For more information, see support.volvocars.com.
United
Arab Emi-
rates:
522
AUDIO, MEDIA AND INTERNET
Country/
Area
Kazakh-
stan
}}
523
AUDIO, MEDIA AND INTERNET
|| Country/
Area
China: 1.
■ 使用频率 2.4 - 2.4835 GHz
■ 等效全向辐射 率(EIRP) 天线增益 10dBi 时 ≤100 mW 或≤20 dBm ①
■ 最大 率谱密度 天线增益 10dBi 时 ≤20 dBm / MHz(EIRP) ①
■ 载频容限 20 ppm
■ 帯外发射 率(在 2.4-2.4835GHz 頻段以外) ≤-80 dBm / Hz (EIRP)
■ 杂散发射(辐射) 率(对应载波±2.5 倍信道带宽以外)
• ≤-36 dBm / 100 kHz (30 - 1000 MHz)
• ≤-33 dBm / 100 kHz (2.4 - 2.4835 GHz)
• ≤-40 dBm / 1 MHz (3.4 - 3.53 GHz)
• ≤-40 dBm / 1 MHz (5.725 - 5.85 GHz)
• ≤-30 dBm / 1 MHz (其它 1 - 12.75 GHz)
2.不得擅自更改发射频率 大发射 率(包括额外 装射频 率放大器),不得擅自外接天线或改用其它发射天线
3.使用时不得对各种合法的无线电通信业 产生有害干扰 一旦发现有干扰现象时,应立即停止使用,并采 措施消除干扰后方可继续
使用
4.使用微 率无线电设备,必须忍 各种无线电业 的干扰或工业 科学及医疗应用设备的辐射干扰
5.不得在飞机和机场附近使用
524
AUDIO, MEDIA AND INTERNET
Country/
Area
Korea: B 급 기기 (가정용 방송통신기자재)
이 기기는 가정용(B 급) 전자파적합기기로서 주로
가정에서 사용하는 것을 적으로 하며, 든
지역에서 사용할 수 있습니다.
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.
Malaysia
This device has been certified under the Communications & Multimedia Act of 1998, Communications and Multimedia (Technical Standards)
Regulations 2000.To retrieve your device’s serial number, please visit (support.volvocars.com) and search for “SIRIM Label Verification”.
Device category: Navigation equipment for vehicle (Bluetooth)
Model: NR-0V
Type Approval No.:
RBAY/18A/1015S(15-4067)
}}
525
AUDIO, MEDIA AND INTERNET
|| Country/
Area
Mexico:
Taiwan: 低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機,非經許可,公司 商號或使用者均不得擅自
變更頻率 加大功率或變更原設計之特性及功能
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應
立停用,改善至無干擾時方得繼續使用 前項合法通信,指依電信法規定作業之無線
電通信 低功率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備
之干擾
Related information
• Audio, media and Internet (p. 464)
• Internet-connected vehicle* (p. 507)
• Media player (p. 485)
• Gracenote® (p. 489)
• Sensus - connection and entertainment
(p. 30)
526 * Option/accessory.
WHEELS AND TIRES
WHEELS AND TIRES
528
WHEELS AND TIRES
imprinted on the sidewall of the tire. The last four • Tires must maintain the same direction of control than a rear-wheel skid (oversteer). If the
digits in the series is the Department of rotation throughout their lifetime. front wheels skid, the vehicle will continue in a
Transportation (DOT) stamp and indicates the • When replacing tires, the tires with the most straight line instead of the rear wheels skidding
week and year the tire was manufactured. The tread should be mounted on the rear wheels to the side, which could cause you to completely
tire in the illustration has 0717 as the last four to reduce the chance of oversteer during lose control of the vehicle. It is therefore impor-
digits, which means it was manufactured week 7 hard braking. tant that the rear wheels never lose grip before
of 2017. the front wheels.
• Hitting curbs or potholes can damage the
Tire age tires and/or wheels permanently. Storing wheels and tires
Tires degrade over time, even when they are not When storing complete wheels (tires mounted on
being used. It is recommended that tires gener- Tire rotation rims), they should be suspended off the floor or
ally be replaced after 6 years of normal service. Your vehicle has no required tire rotation. Driving placed on their sides on the floor.
Heat caused by hot climates, frequent high load- style, tire pressure, climate and road conditions
affect how quickly the tires age and exhibit signs Tires not mounted on rims should be stored on
ing conditions or Ultra Violet (U.V.) exposure can
of wear. Maintaining the correct tire pressure their sides or standing upright, but should not be
accelerate the aging process. The temporary
helps keep tread wear evenly distributed. suspended.
spare 2 should also be replaced at 6-year inter-
vals, even if it has never been used. A tire with To help prevent differences in tread depth and
e.g., visible cracks or discoloration should be wear patterns forming on the tires, the front and CAUTION
replaced immediately. rear wheels should be rotated, i.e. the front tires Tires should preferably be stored in a cool,
moved to the rear and the rear tires moved to the dry, dark place, and should never be stored in
Tire economy front. Ideally, tire rotation should be done the first close proximity to solvents, gasoline, oils, etc.
• Maintain correct tire pressure. time after approximately 5000 km (ca
• Avoid fast starts, hard braking and tire 3100 miles) and thereafter at 10,000 km
screeching. (approx. 6200 miles) intervals.
• Tire wear increases with speed. If you have any questions regarding tread depth,
• Correct front wheel alignment is very impor- Volvo recommends consulting an authorized
tant. Volvo workshop. If significant differences in wear
(> 1 mm difference in tread depth) between the
• Unbalanced wheels impair tire economy and tires have already occurred, the least worn tires
driving comfort. should always be mounted on the rear wheels. A
front-wheel skid (understeer) is usually easier to
529
WHEELS AND TIRES
Related information
• Checking tire pressure (p. 535)
The arrow shows the tire's direction of rotation.
• Tire direction of rotation (p. 530)
• The tire should maintain the same direction
• Tread wear indicator (p. 531) of rotation throughout its service life.
• Tire pressure monitoring system* (p. 537)
• Tires should only be moved between the
• Tire sealing system (p. 550) front and back, never from right to left or vice
• Uniform Tire Quality Grading (p. 534) versa.
• Tire terminology (p. 531) • Incorrectly mounted tires impair the vehicle's
braking properties and ability to force aside
• Tire sidewall designations (p. 532) rain, snow and slush.
• Loading recommendations (p. 564)
• The tires with the most tread should always
be mounted on the rear wheels to help
reduce the risk of skidding.
530 * Option/accessory.
WHEELS AND TIRES
Tread wear indicator Tire terminology • B-pillar: The structural member at the side
The tread wear indicator shows the status of the The following is a glossary of tire-related terms. of the vehicle behind the front door.
tire's tread. The tire suppliers may have additional markings, • Bead area of the tire: Area of the tire next
notes or warnings such as standard load, radial to the rim.
tubeless, etc.
• Sidewall of the tire: Area between the bead
• Tire information placard: A placard show- area and the tread.
ing the OE (Original Equipment) tire sizes, • Tread area of the tire: Area of the perime-
recommended inflation pressure, and the ter of the tire that contacts the road when
maximum weight the vehicle can carry. mounted on the vehicle.
• Tire Identification Number (TIN): A number • Rim: The metal support (wheel) for a tire or a
on the sidewall of each tire providing infor- tire and tube assembly upon which the tire
mation about the tire brand and manufactur- beads are seated.
ing plant, tire size and date of manufacture.
• Maximum load rating: a figure indicating
• Inflation pressure: A measure of the the maximum load in pounds and kilograms
amount of air in a tire. that can be carried by the tire. This rating is
The tread wear indicator is a narrow elevated • Standard load: A class of P-metric or Metric established by the tire manufacturer.
strip running across the tire's longitudinal tread tires designed to carry a maximum load at 35 • Maximum permissible inflation pressure:
grooves. The letters TWI (Tread Wear Indicator) psi [37 psi (2.5 bar) for Metric tires]. Increas- the greatest amount of air pressure that
are visible on the side of the tire. When approxi- ing the inflation pressure beyond this pres- should ever be put in the tire. This limit is set
mately 1.6 mm (1/16 inch) is left on the tread, sure will not increase the tires load carrying by the tire manufacturer.
the tread will be at the same height as the tread capability.
wear indicator. Replace the tire as soon as possi- • Recommended tire inflation pressure:
• Extra load: A class of P-metric or Metric inflation pressure, established by Volvo,
ble. Tires with low tread offer very poor traction in tires designed to carry a heavier maximum which is based on the type of tires that are
rain or snow. load at 41 psi [43 psi (2.9 bar) for Metric mounted on a vehicle at the factory. This
tires]. Increasing the inflation pressure information can be found on the tire inflation
Related information
beyond this pressure will not increase the placard(s) located on the driver's side B-pillar
• Tires (p. 528)
tire's load carrying capability. and in the tire inflation table in this chapter.
• kPa: Kilopascal, a metric unit of air pressure. • Cold tires: The tires are considered to be
• PSI: Pounds per square inch, a standard unit cold when they have the same temperature
of air pressure. as the surrounding (ambient) air. This tem-
}}
531
WHEELS AND TIRES
|| perature is normally reached after the vehicle Tire sidewall designations NOTE
has been parked for at least 3 hours. The following information can be found on a
Please be aware that the following tire desig-
tire's sidewall.
Related information nation is an example only and that this par-
• Tires (p. 528) ticular tire may not be available on your vehi-
cle.
532
WHEELS AND TIRES
533
WHEELS AND TIRES
534
WHEELS AND TIRES
Checking tire pressure WARNING correct pressure, which can be found on the vehi-
Correct inflation pressure helps improve driving cle's tire information placard or certification label.
stability, save fuel and increase the service life of • Under-inflation is the most common
cause of tire failure and may result in If you check inflation pressure when the tires are
the tires. warm, you should never release air. The tires
severe tire cracking, tread separation, or
"blow-out," with unexpected loss of vehi- become warm after driving and it is normal for
Tire pressure decreases over time, which is nor-
cle control and increased risk of injury. warm tires to have an inflation pressure above
mal. Tire pressure also varies depending on the
the recommended pressure for cold tires. A warm
ambient temperature. Driving on under-inflated • Under-inflated tires reduce the load car- tire with an inflation pressure equal to or under
tires could cause the vehicle to overheat and lead rying capacity of your vehicle. the recommended pressure for cold tires could
to damage. Tire pressure affects traveling com-
be significantly under-inflated.
fort, road noise and driving characteristics.
Cold tires
Check the pressure in the tires every month. Use Inflation pressure should be checked when the Related information
the recommended inflation pressure for cold tires tires are cold. • Adjusting tire pressure (p. 536)
for optimal tire performance and wear. Under-
The tires are considered to be cold when they • Recommended tire pressure (p. 537)
inflated or over-inflated tires could cause uneven
tread wear.
have the same temperature as the surrounding • Tire pressure monitoring system* (p. 537)
(ambient) air. • Tires (p. 528)
Use an air pressure gauge and check the infla- This temperature is normally reached after the
tion pressure on all the tires, including the spare vehicle has been parked for at least 3 hours.
tire4, at least once a month and before long trips.
Volvo strongly recommends buying a reliable air After driving for approximately 1.6 km (1 mile),
pressure gauge, as the automatic gauges provi- the tires are considered to be warm. If you need
ded at service stations may be inaccurate. to drive longer than that to inflate the tires, check
and record the inflation pressure of the tires first
and inflate accordingly when you arrive at the
pump.
When the ambient temperature changes, so does
the inflation pressure. A 10-degree temperature
drop causes a corresponding drop in inflation
pressure of 1 psi (7 kPa). Check the inflation
pressure of the tires regularly and adjust to the
* Option/accessory. 535
WHEELS AND TIRES
Adjusting tire pressure 3. Screw the valve cap back on. NOTE
Tire pressure decreases over time, which is nor-
If you have overfilled the tire, release air by
mal. The tire pressure must therefore be NOTE
pushing on the metal stem in the center of
adjusted to maintain the recommended tire pres-
sure.
• After inflating a tire, always replace the the valve. Then recheck the pressure with
valve cap to help prevent valve damage your tire gauge.
Use the recommended inflation pressure for cold caused by gravel, dirt, etc.
tires for optimal tire performance and wear. Some spare tires require higher inflation pres-
• Use plastic valve caps only. Metal caps sure than the other tires. Consult the tire
could corrode and become difficult to inflation pressure table or the inflation pres-
NOTE remove. sure placard.
To help prevent incorrect inflation pressure,
pressure should be checked when the tires 4. Visually inspect the tire to make sure there
are cold. The tires are considered to be cold Related information
are no nails or other embedded objects that
when they have reached the same tempera- • Recommended tire pressure (p. 537)
could puncture the tire and cause air leak-
ture as the ambient temperature (about 3 age. • Checking tire pressure (p. 535)
hours after the vehicle was last driven). After
5. Check the sidewalls to make sure there are • Inflate tires with the compressor included in
driving for a few kilometers, the tires will warm the tire sealing system (p. 555)
up and the pressure will increase. no gouges, cuts, bulges or other irregulari-
ties. • Approved tire pressure (p. 647)
1. Remove the valve cap from the tire and press 6. Repeat this procedure for each tire, including
the air pressure gauge firmly onto the valve. the spare tire5.
2. Inflate to the recommended inflation pres-
sure.
536
WHEELS AND TIRES
Recommended tire pressure Tire pressure monitoring system* ted to the inflation pressure recommended by the
The tire pressure placard on the driver's side B The tire pressure monitoring system, Tyre vehicle manufacturer on the vehicle placard or
pillar (between the front and the rear door) indi- Pressure Monitoring System (TPMS), provides a tire inflation pressure label. (If your vehicle has
cates tire pressure for different loads and speed warning symbol in the instrument panel if pres- tires of a different size than the size indicated on
conditions. sure is too low in one or more tires. the vehicle placard or tire inflation pressure label,
you should determine the proper tire inflation
Symbol Explanation pressure for those tires.)
This symbol illuminates to indicate As an added safety feature, your vehicle has
low inflation pressure. been equipped with a tire pressure monitoring
If there is a system malfunction, the system (TPMS) that illuminates a low tire pres-
inflation pressure warning symbol sure telltale when one or more of your tires is
will flash for approximately one significantly under-inflated. Accordingly, when the
minute and then glow steadily. low tire pressure telltale illuminates, you should
stop and check your tires as soon as possible,
System description and inflate them to the proper pressure.
The tire pressure monitoring system measures Driving on a significantly under-inflated tire cau-
differences in rotational speed between the ses the tire to overheat and can lead to tire fail-
The placard specifies the designation for the fac- wheels through the ABS system to determine if ure. Under-inflation also reduces fuel efficiency
tory-mounted tires on the vehicle, as well as load the tires are properly inflated. If inflation pressure and tire tread life, and may affect the vehicle's
limits and inflation pressures. in a tire is too low, its diameter (and consequently handling and stopping ability. Please note that
its rotational speed) changes. By comparing the the TPMS is not a substitute for proper tire main-
Related information tires with each other, the system can determine if tenance, and it is the driver's responsibility to
• Checking tire pressure (p. 535) the pressure in one or more tires is too low. maintain correct tire pressure, even if under-infla-
• Approved tire pressure (p. 647) General information about the tire pressure tion has not reached the level to trigger illumina-
tion of the TPMS low tire pressure telltale.
monitoring system
In the following description, the tire monitoring Your vehicle has also been equipped with a
system is generally referred to as TPMS. TPMS malfunction indicator to indicate when the
system is not operating properly. The TPMS mal-
Each tire, including the spare tire (if provided)6, function indicator is combined with the low tire
should be checked monthly when cold and infla- pressure telltale. When the system detects a mal-
* Option/accessory. 537
WHEELS AND TIRES
|| function, the telltale will flash for approximately pressure placard on the driver's side B pillar • Calibrating the tire pressure monitoring sys-
one minute and then remain continuously illumi- for Volvo-recommended tire pressures. tem* (p. 539)
nated. This sequence will continue upon subse- • If you switch to a tire of another size than the
quent vehicle start-ups as long as the malfunc- factory-mounted tires, the system must be
tion exists. When the malfunction indicator is illu- calibrated for these tires to avoid false warn-
minated, the system may not be able to detect or ings.
signal low tire pressure as intended.
• If a spare wheel7 is used, it is possible that
TPMS malfunctions may occur for a variety of the tire pressure monitoring system will not
reasons, including the installation of replacement work correctly due to the differences
or alternate tires or wheels on the vehicle that between the wheels.
prevent the TPMS from functioning properly.
• The system does not replace the need for
Always check the TPMS malfunction telltale after regular tire inspection and maintenance.
replacing one or more tires or wheels on your
vehicle to ensure that the replacement or alter-
• It is not possible to deactivate the tire pres-
sure monitoring system.
nate tires and wheels allow the TPMS to con-
tinue to function properly.
WARNING
Messages in the instrument panel • Incorrect inflation pressure could lead to
If tire pressure is too low, the low tire pressure tire failure, which could cause the driver
warning symbol is shown in the instrument panel to lose control of the vehicle.
along with a message.
• The system cannot predict sudden tire
• Tire pressure low Check tires, calibrate damage.
after fill
• Tire pressure system Temporarily Related information
unavailable • Recommended tire pressure (p. 537)
• Tire pressure system Service required • Viewing tire pressure status in the center
display* (p. 540)
To keep in mind
• Always calibrate the system after changing • Action when warned of low tire pressure
wheels or adjusting tire pressure. See the tire (p. 541)
538 * Option/accessory.
WHEELS AND TIRES
Calibrating the tire pressure 5. Tap TPMS. 8. Run the car until calibration is complete.
monitoring system* Calibration is done when the vehicle is driv-
In order for the tire pressure monitoring system, ing at a speed above 35 km/h (22 mph).
Tyre Pressure Monitoring System (TPMS), to > When enough data has been collected for
function correctly, tire pressure reference values the system to detect low tire pressure, the
must be set correctly. This must be done each color of the tire symbols in the center dis-
time the tires are changed or the tire pressure is play will change from gray to green. The
adjusted. system will not provide any other confir-
For example, when driving with a heavy load or at NOTE mation that calibration has been comple-
high speeds (over 160 km/h (100 mph)), tire ted.
The car must be stationary when calibration is
pressure should be adjusted to the Volvo-recom- started. If the car's ignition is switched off before
mended tire pressure values. The system should calibration is complete, the tires in the
then be recalibrated. center display change color from gray to
6. Tap Calibrate.
1. Switch off the ignition. green upon next start-up, even if calibra-
7. Tap OK to confirm that the tire pressure in tion is not complete. Perform the calibra-
2. Inflate the tires to the pressure indicated on all four tires has been checked and adjusted. tion again and allow it to complete within
the tire pressure placard on the driver's side the same operating cycle to ensure that
B pillar. the calibration is carried out correctly.
3. Start the vehicle. If start-up of calibration fails, the following
4. Open the Car status app in App view. message appears: Calibration
unsuccessful. Try again..
}}
* Option/accessory. 539
WHEELS AND TIRES
8 The illustration is generic. Layout may vary depending on vehicle model or software version.
540 * Option/accessory.
WHEELS AND TIRES
The vehicle may need to be driven for a few Action when warned of low tire NOTE
minutes at a speed above 35 km/h (22 mph) to pressure
activate the system. To help prevent incorrect inflation pressure,
When the tire pressure monitoring system, Tyre
pressure should be checked when the tires
All tires gray and a message: Pressure Monitoring System (TPMS), detects
are cold. The tires are considered to be cold
low pressure in one or more of the vehicle's
• Tire pressure system Temporarily tires, the driver will be alerted that action is nee-
when they have reached the same tempera-
unavailable. The indicator symbol will flash ture as the ambient temperature (about 3
ded.
for about 1 minute and then glow steadily. hours after the vehicle was last driven). After
If the system's indicator symbol illumi-
The system is temporarily unavailable and will driving for a few kilometers, the tires will warm
nates and the message Tire pressure
be activated momentarily. up and the pressure will increase.
low is displayed, check the tire pres-
• Tire pressure system Service required. sure and inflate if necessary.
The indicator symbol will flash for about 1 NOTE
1. Switch off the ignition.
minute and then glow steadily. If the system
is not working properly, contact a workshop9. 2. Check the inflation pressure on all four tires • After inflating a tire, always replace the
using a tire pressure gauge. valve cap to help prevent valve damage
Related information caused by gravel, dirt, etc.
3. Inflate the tire to the correct pressure (see
• Calibrating the tire pressure monitoring sys-
the tire pressure decal on the driver's side • Use plastic valve caps only. Metal caps
tem* (p. 539) could corrode and become difficult to
door pillar).
• Action when warned of low tire pressure remove.
(p. 541) 4. Through calibration of the system via the
center display after the tire pressure has
• Tire pressure monitoring system* (p. 537) been adjusted. WARNING
• Vehicle status (p. 580)
Please be aware that the indicator symbol • Incorrect inflation pressure could lead to
will not go out until the low tire pressure has tire failure, which could cause the driver
been corrected and the system has been to lose control of the vehicle.
recalibrated. • The system cannot predict sudden tire
damage.
* Option/accessory. 541
WHEELS AND TIRES
Related information
• When changing wheels (p. 542)
• Jack* (p. 543)
542 * Option/accessory.
WHEELS AND TIRES
}}
* Option/accessory. 543
WHEELS AND TIRES
544 * Option/accessory.
WHEELS AND TIRES
1. Turn on the vehicle's hazard warning flashers 5. Using the lug wrench*, screw the towing eye 8. When hoisting the vehicle, it is important that
if a wheel change must be performed in an into place as far as possible according to the the jack* or garage lift arms are positioned
area with traffic. instructions. on the designated points under the vehicle.
2. Apply the parking brake and put the gear The triangle markings on the plastic cover
selector in P. indicate where the jack attachment points/
lifting points are located. There are two jack
For vehicles with Leveling Control*: If the attachment points on each side of the vehi-
vehicle is equipped with pneumatic suspen- cle. There is a groove for the jack at each
sion, this must be switched off before the attachment point.
vehicle is lifted with the jack*.
3. Take out the jack*, lug wrench* and tool for
removing the plastic covers, which are
stowed in the foam block.
CAUTION
The towing eyelet must be screwed into the
lug wrench* as far as possible.
}}
* Option/accessory. 545
WHEELS AND TIRES
546 * Option/accessory.
WHEELS AND TIRES
* Option/accessory. 547
WHEELS AND TIRES
548
WHEELS AND TIRES
Studded tires
Studded tires should be broken in by driving
500–1000 km (300–600 miles) slowly and gen-
tly to help the studs settle properly in the tires.
This gives the tire, and especially the studs, a
longer service life.
NOTE
Regulations regarding the use of studded
tires vary from country to country.
}}
549
WHEELS AND TIRES
• Always follow the manufacturer's installa- • Some types of strap-on chains affect The tire sealing system consists of a compressor
tion instructions carefully. Install chains brake components and therefore must and a bottle containing sealing compound. The
as tightly as possible and retighten peri- NOT be used. sealing functions as a temporary repair.
odically.
• Only put snow chains on the front wheels Consult a Volvo retailer for more information NOTE
(also applies to all-wheel drive vehicles). about snow chains. The sealing compound effectively seals tires
• If accessory, aftermarket or "custom"
Related information
with punctures in the tread but may not be
tires and wheels with different dimen- able to fully seal tires with punctures in the
sions than the original tires and wheels • Winter driving (p. 440)
sidewall. Do not use the tire sealing system
are used, snow chains in some cases on tires with large tears, cracks or similar
may NOT be used. Sufficient distance damage.
between the chains and brakes, suspen-
sion and body components must be
maintained. NOTE
• Check local regulations regarding the use The compressor is intended for temporary tire
of snow chains before installing. sealing and is approved by Volvo.
• Never exceed the snow chain manufac-
turer's specified maximum speed limit. Location
Under no circumstances should you The tire sealing system is located in a foam block
exceed 50 km/h (30 mph). under the floor of the cargo compartment.
• Avoid bumps, holes or sharp turns when
driving with snow chains.
550
WHEELS AND TIRES
Overview Connecting
551
WHEELS AND TIRES
|| WARNING • Inhalation: Move the exposed person to 3. Make sure the switch is in the 0 (Off) posi-
fresh air. If irritation persists, get medical tion and take out the electric cable and the
Please keep the following points in mind attention. hose.
when using the tire sealing system:
• Ingestion: Do NOT induce vomiting 4. Unscrew the orange cover on the compres-
• The sealing compound bottle (no. 8 in the unless directed to do so by medical per- sor and unscrew the cap on the sealing com-
illustration) contains 1) rubber latex, natu- sonnel. Get medical attention. pound bottle.
ral and 2) ethanediol. These substances
are harmful if swallowed. • Disposal: Dispose of this material and its 5. Screw the bottle onto the bottle holder as far
container at a hazardous or special waste as possible.
• The contents of this bottle may cause collection point.
allergic skin reactions or otherwise be The bottle and the bottle holder are equip-
potentially harmful to the respiratory tract, ped with catches to help prevent the sealing
the skin, the central nervous system, and WARNING compound from leaking. Once the bottle is
the eyes. screwed into place into the bottle holder, it
• Do not remove the bottle while the tire
cannot be unscrewed. The bottle can only be
Precautions: sealing system is being used.
removed by a workshop. Volvo recommends
• Keep out of reach of children. • Do not remove the hose while the tire an authorized Volvo workshop.
• Do not ingest the contents. sealing system is being used.
• Avoid prolonged or repeated contact with WARNING
the skin. Remove any clothing that has 1. Turn on the vehicle's hazard warning flashers
Do not unscrew the bottle. It is equipped with
come into contact with sealant. if the tire sealing system is to be used in an
a catch to prevent leakage.
area with traffic.
• Wash thoroughly after handling.
First aid: If the puncture was caused by a nail or simi- 6. Unscrew the tire's valve cap and screw the
lar object, do not remove it. It will help seal hose's valve connector as far as possible
• Skin: Wash affected areas of the skin the hole. onto the valve.
with soap and water. Get medical atten-
tion if symptoms occur. 2. Peel off the speed limit sticker from the side Be sure the air release valve on the com-
of the compressor. Affix the decal to a clearly pressor's hose is completely closed.
• Eyes: Flush with plenty of water for least
visible location on the windshield to remind
15 minutes, occasionally lifting the upper
the driver not to exceed this speed limit. Do
and lower eyelids. Get medical attention if
not drive faster than 80 km/h (50 mph) while
symptoms occur.
using a tire that has been temporarily
repaired with the tire sealing system.
552
WHEELS AND TIRES
7. Connect the electrical cable to the nearest 8. Start the compressor by moving the switch to 10. Switch off the compressor and check the
12 V outlet and start the vehicle. the I (On) position. inflation pressure using the air pressure
gauge. The inflation pressure should be
NOTE WARNING between 1.8 bar (22 psi) and 3.5 bar
(51 psi). If the inflation pressure is too high,
Make sure that none of the vehicle's other Never stand next to a tire being inflated with use the air release valve to release air.
12 V sockets are used while the compressor the compressor. If cracks, bulges, etc. form on
is running. the tire, switch off the compressor immedi-
ately. The vehicle should not be driven. Call WARNING
roadside assistance to have the vehicle towed
If the bottle is not removed in the correct
WARNING to a workshop for inspection/replacement of
order, sealant could spill out.
the tire. Volvo recommends an authorized
Never leave children unattended in the vehicle workshop.
while the engine is running.
WARNING
NOTE If pressure falls below 1.8 bar (22 psi), the
hole in the tire may be too large. The vehicle
When the compressor first starts, air pressure should not be driven. Call roadside assistance
may temporarily increase up to 6 bar (88 psi) to have the vehicle towed to a workshop for
but should decrease again after approxi- inspection/replacement of the tire. Volvo rec-
mately 30 seconds. ommends an authorized workshop.
9. Inflate the tire for 7 minutes. 11. Switch off the compressor and remove the
electrical cable.
CAUTION 12. Unscrew the hose from the tire's valve and
To help avoid overheating, the compressor screw the valve cap back on.
should never be used for more than 13. Put the protective hose cover onto the hose
10 minutes at a time. to help prevent leakage of any residual seal-
ing compound. Return the equipment to the
cargo compartment.
}}
553
WHEELS AND TIRES
|| 14. Immediately drive the vehicle at least 3 km 16. Check the inflation pressure on the air pres- WARNING
(2 miles) at a maximum speed of 80 km/h sure gauge.
(50 mph) to allow the sealing compound to After using the tire sealing system, the vehicle
seal the tire, and then recheck the inflation
• If the pressure is under 1.3 bar (19 psi), should not be driven farther than approxi-
the tire is not sufficiently sealed. The vehi- mately 200 km (120 miles).
pressure.
cle should not be driven. Call roadside
assistance to have the vehicle towed.
NOTE NOTE
• If the inflation pressure is higher than
During the tire's first revolution, some sealing 1.3 bar (19 psi), the tire must be inflated The compressor is an electric device. Follow
compound may spray out of the puncture to the inflation pressure specified on the local regulations for disposal.
hole. tire pressure decal on the driver's side
door pillar (1 bar = 100 kPa = 14.5 psi). If Related information
the inflation pressure is too high, use the • Recommended tire pressure (p. 537)
WARNING air release valve to release air.
Before driving away, make sure that no one is • Tire sealing system (p. 550)
near the vehicle who could be sprayed with NOTE • Inflate tires with the compressor included in
sealing compound. Make sure no one is the tire sealing system (p. 555)
within 2 meters(7 feet) of the vehicle. Replace the sealing compound bottle and
hose after use. Volvo recommends having
15. Rechecking the inflation pressure these replaced by an authorized Volvo work-
shop.
Connect the hose to the tire's valve and
screw the hose connector onto the valve as
far as possible. The compressor must be WARNING
switched off. Check inflation pressure regularly.
554
WHEELS AND TIRES
WARNING NOTE
Never leave children unattended in the vehicle
The compressor is an electric device. Follow
while the engine is running.
local regulations for disposal.
555
WHEELS AND TIRES
Determining the vehicle's permitted Steps for Determining Correct Load WARNING
weight Limit
Properly loading your vehicle will provide maxi- 1. Locate the statement "the combined weight • Exceeding the permissible axle weight,
of occupants and cargo should never exceed gross vehicle weight, or any other weight
mum return of vehicle design performance.
XXX kg or XXX lbs." on your vehicle's plac- rating limits can cause tire overheating
Weight designations ard. resulting in permanent deformation or
Before loading your vehicle, familiarize yourself catastrophic failure.
2. Determine the combined weight of the driver
with the following terms for determining your
and passengers that will be riding in your
• Do not use replacement tires with lower
vehicle's weight ratings, with or without a trailer, load carrying capacities than the tires that
vehicle.
from the vehicle's Federal/Canadian Motor Vehi- were original equipment on the vehicle
cle Safety Standards (FMVSS/CMVSS) label, and 3. Subtract the combined weight of the driver because this will lower the vehicle's GVW
the vehicle's tire information placard: and passengers from XXX kg or XXX lbs. rating. Use only tires with the correct load
carrying capacity. Consult your Volvo
Curb weight 4. The resulting figure equals the available
retailer for information.
The weight of the vehicle including a full tank of amount of cargo and luggage load capacity.
fuel and all standard equipment. It does not For example, if the "XXX" amount equals
include passengers, cargo, or optional equipment. 1400 lbs. and there will be five 150 lb. pas- Related information
Capacity weight
sengers in your vehicle, the amount of availa- • Loading recommendations (p. 564)
ble cargo and luggage load capacity is 650
All weight added to the curb weight, including
lbs. (1400 - 750 (5 × 150) = 650 lbs.)
cargo and optional equipment. When towing, tow-
bar weight is also part of cargo weight. 5. Determine the combined weight of luggage
Permissible axle weight and cargo being loaded on the vehicle. That
weight may not safely exceed the available
The maximum allowable weight that can be car-
cargo and luggage load capacity calculated
ried by a single axle (front or rear). These num-
in Step 4.
bers are shown on the Federal/Canadian Motor
Vehicle Safety Standards (FMVSS/CMVSS) label. 6. If your vehicle will be towing a trailer, load
The total load on each axle must never exceed its from your trailer will be transferred to your
maximum permissible weight. vehicle. Consult this manual to determine
Gross vehicle weight (GVW) how this reduces the available cargo and lug-
The vehicle's curb weight + cargo + passengers. gage load capacity of your vehicle.
556
LOADING, STORAGE AND PASSENGER COM-
PARTMENT
LOADING, STORAGE AND PASSENGER COMPARTMENT
Front seats
CAUTION
Keep in mind that glossy surfaces can be
easily scratched by e.g. metal objects. Do not
place keys, phones or similar items on sensi-
tive surfaces.
558 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory. 559
LOADING, STORAGE AND PASSENGER COMPARTMENT
12 V outlets
560 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
Related information
• Passenger compartment interior (p. 558)
• Using the electrical outlets (p. 562)
561
LOADING, STORAGE AND PASSENGER COMPARTMENT
562 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory. 563
LOADING, STORAGE AND PASSENGER COMPARTMENT
564 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
WARNING down, make sure that no objects loaded into the The rear end will return to the normal height
vehicle prevent the WHIPS system for the front when the vehicle begins driving.
In a head-on collision at a speed of 50 km/h seats from functioning correctly.
(30 mph), an unsecured object weighing 20
kg (44 pounds) can reach a projectile weight NOTE
Raising/lowering the rear end of the
equivalent to 1000 kg (2200 pounds). It is not possible to adjust the height of the
vehicle*
The rear end of the vehicle can be lowered or vehicle's rear when one or more of the doors
WARNING raised for easier loading or to facilitate attaching or the hood is open. This does not apply to
a trailer*. the tailgate.
If objects are loaded higher than the upper
edge of the side windows, leave a 10 cm (4 The controls for raising/lowering are located at
in.) space between the objects and the win- the rear edge of the cargo compartment's right WARNING
dow. Objects placed closer to this could side panel.
impede the function of the inflatable curtain Make sure that no people, animals or objects
concealed inside the headlining. are found under the vehicle when it is low-
ered. This could endanger life and cause
damage to the vehicle or objects.
WARNING
Always secure the load. Otherwise, it may shift Related information
during heavy braking and injure people in the • Load anchoring eyelets (p. 567)
vehicle.
• Folding the second row backrests (p. 196)
Cover sharp edges and sharp corners with
something soft. • Roof loads and load carriers (p. 566)
Turn off the engine and apply the parking • Leveling control* and suspension (p. 432)
brake when loading/unloading long objects. • Weights (p. 641)
Otherwise, it is possible for the load to reach
the gear lever or gear selector and move it to Controls for raising/lowering the rear end of the vehicle.
a drive position – which could cause the vehi-
cle to begin rolling. The controls consist of two buttons ‒ one button
for lowering and one button for raising the rear
end. Press and hold the relevant button until the
Extra cargo space
desired height is reached.
The rear seat backrests can be folded down to
increase cargo compartment space and simplify The rear end of the vehicle cannot be raised
loading. If the rear seat backrests are folded higher than its normal height.
* Option/accessory. 565
LOADING, STORAGE AND PASSENGER COMPARTMENT
Roof loads and load carriers Grocery bag holders Under the floor hatch*3
Volvo-developed load carriers are recommended Grocery bag holders (hooks) help keep shop-
for carrying loads on the roof of the vehicle. ping bags in place and prevent them from falling
Volvo load carriers are specially designed to help over and spilling their contents in the cargo
prevent damage to your vehicle and help ensure compartment.
maximum safety while driving. Volvo load carriers
are available from authorized Volvo retailers. On the sides of the cargo compartment
Carefully follow the installation instructions provi-
ded with the load carriers.
• Check periodically to ensure that the load
carriers and load are properly secured.
Secure the load firmly using tie straps or
similar.
There are two grocery bag holders and an elastic
• Distribute the load evenly throughout the
band4 in the hatch in the cargo compartment
load carriers. Place heavier cargo at the bot-
floor. The strap can be attached in four different
tom of the load.
positions.
• The vehicle's wind resistance and fuel con-
sumption increase with the size of the load. Open the hatch to access the grocery bag hold-
ers. Use the provided elastic strap to secure
• Drive smoothly. Avoid rapid acceleration, hard There are two fold-out holders in the side panels, shopping bags in a suitable position. Bags with
braking and fast cornering. one on each side of the cargo compartment. handles of a suitable size can also be hung on
CAUTION the hooks.
WARNING
The vehicle's center of gravity and driving
The grocery bag holders are only intended to Related information
characteristics are altered by roof loads.
hold weights up to 5 kg (11 lbs). • Loading recommendations (p. 564)
Follow the vehicle's specifications regarding • Installing and removing the cargo net*
weights and maximum permitted load. (p. 571)
• Installing and removing the cargo compart-
Related information ment cover* (p. 567)
• Loading recommendations (p. 564) • Installing and removing the steel cargo grid*
• Weights (p. 641) (p. 570)
566 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
Load anchoring eyelets Installing and removing the cargo Push the end piece down on both sides, one
The fold-out eyelets in the cargo compartment compartment cover* at a time.
can be used to secure objects with straps, a net, The cover can be rolled out to conceal objects > When a click is heard and the red marks
etc. in the cargo compartment. on each end piece are no longer visible,
the cover is in place. Check that it is
secure.
Installing the cargo compartment cover
Removing the cargo compartment
cover
In retracted position:
1. Press the button on one of the cover's ends
and lift out that end.
For 7-seat models - remove the third row
seat belt latches from the hooks above the
side panels.
2. Carefully lift the cover up and out.
> The other end will release automatically
WARNING and the cover can then be lifted out of the
Hard, sharp and/or heavy objects in or pro- Press the end piece on one side of the cover cargo compartment.
truding from the vehicle can cause injury in into the retaining bracket in the side panel of
the event of hard braking. the cargo compartment. Related information
Always secure large and heavy objects with a Then put the other end piece in the recess in
• Operating the cargo compartment cover*
seat belt or cargo retaining straps. (p. 568)
the side panel on the opposite side.
• Loading recommendations (p. 564)
Related information
• Loading recommendations (p. 564)
• Weights (p. 641)
* Option/accessory. 567
LOADING, STORAGE AND PASSENGER COMPARTMENT
Fully open
7-seat models
1. Grasp the handle and pull the cover out and
above the side panels in the cargo compart-
Grasp the handle and pull the cover out and
ment. Pull the cover to its end position.
above the side panels in the cargo compart-
With the cover completely open (covering the ment. Pull the cover to its end position.
cargo compartment), press the attaching
With the cover completely open (covering the
pins at the end of the cover into the grooves
cargo compartment), press the attaching
on the side panels and release the cover
pins at the end of the cover into the grooves
slightly while pressing the handle lightly
on the side panels and release the cover
downward to hook the pins into the grooves.
slightly while pressing the handle lightly
> The cover will be secured in the fully open downward to hook the pins into the grooves.
position.
> The cover will be secured in the fully open
position.
568 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory. 569
LOADING, STORAGE AND PASSENGER COMPARTMENT
Installing and removing the steel ing brackets has a screw cover and two plastic
cargo grid* sleeves for the grid.
The steel cargo grid prevents loads or pets in
the cargo compartment from being thrown for- WARNING
ward into the passenger compartment. The steel cargo grid may only be used in the
rear position described here. The ceiling
attachment points behind the front seats are
not intended to anchor the steel grid.
The steel cargo grid and the cargo compart- 3. Repeat step 2 above to secure the other
For safety reasons, the steel grid must always be ment cover cannot be mounted at the same hook in the attachment point on the opposite
installed and secured correctly. time. side.
570 * Option/accessory.
LOADING, STORAGE AND PASSENGER COMPARTMENT
* Option/accessory. 571
LOADING, STORAGE AND PASSENGER COMPARTMENT
|| WARNING 3. Insert the other upper hook into the ceiling 4. Rear mounting: With the cargo net hooked
mounting point on the opposite side. The into the rear ceiling mounting points, attach
Objects in the cargo compartment must telescopic spring-loaded hooks make mount- the net's straps into the front floor eyelets in
always be securely anchored, even with a cor- ing easier. the cargo compartment.
rectly installed cargo net.
Make sure that the net's hooks are pushed
Installing the cargo net forward as far as possible into their respec-
tive mounting points.
WARNING
All of the cargo net's upper consoles, hooks
and straps must be securely mounted and
attached before the net is used.
Never use the net if it is damaged.
NOTE
With front mounting, the cargo net is most Rear mounting.
easily installed via a rear door.
Front mounting: With the cargo net mounted
in the front ceiling mounting points, hook the
1. Fold out the cargo net and make sure that
straps into the outer eyelets on the front seat
the upper rod folds out and locks into posi-
rails behind the seats. Attaching the net is
tion.
easier if the seat backrests are upright and
2. Insert one of the net's hooks into the front or the seats are moved slightly forward.
rear ceiling mounting point with the strap
lock facing you.
572
LOADING, STORAGE AND PASSENGER COMPARTMENT
Front mounting. 4. Press the red button on the rod so that it can
be folded. Fold and roll up the net. Store the
Move the seat or backrest only until it net in its case.
touches the net. Moving it with too much
force or applying too much pressure to the Related information
net could lead to damage. • Loading recommendations (p. 564)
• Load anchoring eyelets (p. 567)
CAUTION
If a seat or backrest is pressed with too much
force back against the cargo net, the net and
its ceiling brackets could be damaged.
573
MAINTENANCE AND SERVICE
MAINTENANCE AND SERVICE
Volvo's service program booklet, are not covered by the warranty. You will Records Information booklet for detailed informa-
To keep the vehicle as safe and reliable as pos- be required to pay for labor and material used. tion concerning each of the warranties.
sible, follow the Volvo service schedule speci- Maintenance Periodic maintenance helps minimize
fied in the Warranty and Maintenance Records Your Volvo passed several major inspections emissions
Information booklet. before it was delivered to you, in accordance with
Volvo specifications. The maintenance proce- NOTE
Volvo recommends having an authorized Volvo
dures outlined in the Warranty and Service
workshop perform service and maintenance. • Refer to your Service and Warranty Book-
Records Information booklet, many of which will
Volvo workshops have the staff, service literature let for a comprehensive service and main-
positively affect your vehicle's emissions, should
and special tools to guarantee the highest quality tenance schedule up to 240,000 km
be performed as indicated. It is recommended
of service. (150,000 miles). This program contains
that receipts for vehicle emission maintenance be
retained in case questions arise concerning inspections and services necessary for
CAUTION maintenance. Inspection and maintenance should the proper function of your vehicle and
also be performed anytime a malfunction is includes components that affect vehicle
To ensure the Volvo warranty is not invalida-
observed or suspected. emissions.
ted, check and follow the Service and War-
ranty Booklet. Applicable warranties - U.S./Canada • The Warranty and Service Records Infor-
In accordance with applicable U.S. and Canadian mation booklet also contains detailed
regulations, the following list of warranties is pro- information concerning the warranties
Introduction that apply to your vehicle.
The maintenance services contain several checks vided.
that require special instruments and tools and • New Vehicle Limited Warranty
therefore must be performed by a qualified tech- On-board Diagnostic System
nician. To keep your Volvo in top condition, spec- • Parts and Accessories Limited Warranty OBD II is part of your vehicle's computerized
ify time-tested and proven Genuine Volvo Parts • Corrosion Protection Limited Warranty engine management system. It stores diagnostic
and Accessories. • Seat Belt and Supplemental Restraint Sys- information about your vehicle's emission con-
tems Limited Warranty trols. It can light the Check Engine light (MIL) if it
The Federal Clean Air Act - U.S. detects an emission control "fault." A "fault" is a
The Federal Clean Air Act requires vehicle manu- • Emission Design and Defect Warranty
component or system that is not performing
facturers to furnish written instructions to the ulti- • Emission Performance Warranty within an expected range. A fault may be perma-
mate purchaser to assure the proper servicing nent or temporary. OBD II will store a message
These are federal warranties. Other warranties
and function of the components that control about any fault.
are provided as required by state/provincial law.
emissions. These services, which are listed in the
Refer to your separate Warranty and Service
"Warranty and Service Records Information"
576
MAINTENANCE AND SERVICE
}}
577
MAINTENANCE AND SERVICE
578
MAINTENANCE AND SERVICE
1 There may be a charge for transmitting data over the Internet, depending on your service plan.
2 There may be a charge for transmitting data over the Internet, depending on your service plan. }}
* Option/accessory. 579
MAINTENANCE AND SERVICE
580 * Option/accessory.
MAINTENANCE AND SERVICE
the instrument panel and at the top of the center 7. Tap the Send appointment request but- 2. To accept the suggested appointment, tap
display. ton. Accept. To decline the suggested appoint-
> You will receive an appointment sugges- ment, tap Send new proposal or Decline.
tion to your vehicle within a couple of For some markets, the system reminds you when
days6. You will also receive the same an appointment time is approaching and the navi-
message via email and when you log in to gation system7 can also guide you to the work-
www.volvocars.com. shop at the appointed time.
On some markets, the message in the
instrument panel indicating that the vehi-
Related information
1. Open the Car status app from App view in
cle requires service will go out once the • Vehicle status (p. 580)
the center display.
appointment request has been sent. • Sending vehicle information to the workshop
2. Tap the Appointments button. (p. 582)
8. Tap Cancel request if you would like to
3. Tap the Request appointment button. cancel your request. • Navigating in the center display's views
(p. 117)
4. Check that your Volvo ID is correct. The appointment request contains information
5. Make sure your preferred Workshop is cor- about your vehicle that helps the workshop plan • Volvo ID (p. 26)
rect. for your visit. • Internet-connected vehicle* (p. 507)
6. In the Tap to write information to the The retailer will send you a digital appointment
Workshop field, you can provide details on suggestion. Information about your retailer is also
what you would like performed during the available in the vehicle so that you can contact
visit or other important information to your your workshop at any time.
workshop.
Accepting an appointment suggestion
When the vehicle has received an appointment
suggestion, a message will be displayed at the
top of the center display.
1. Tap the message.
* Option/accessory. 581
MAINTENANCE AND SERVICE
582 * Option/accessory.
MAINTENANCE AND SERVICE
}}
* Option/accessory. 583
MAINTENANCE AND SERVICE
||
The triangles in the plastic covering indicate where the jack attachment points/lifting points (red areas) are located.
Related information
• Removing a wheel (p. 544)
• Jack* (p. 543)
• Leveling control settings* (p. 435)
584 * Option/accessory.
MAINTENANCE AND SERVICE
WARNING
Risk of injury! When closing, make sure that
the hood is completely unobstructed and that
no one can be injured.
NOTE
If the warning symbol is illuminated or an
audible warning signal sounds even though
the hood is securely closed, consult a work-
shop - an authorized Volvo workshop is rec-
ommended. Hood not completely closed. The illustration is generic -
details may vary according to vehicle model.
}}
585
MAINTENANCE AND SERVICE
Hood completely closed. The illustration is generic - Vehicles with R134a refrigerant Related information
details may vary according to vehicle model. • Head-up display* (p. 144)
WARNING • Cleaning the head-up display* (p. 616)
WARNING The air conditioning system contains the
Never drive with the hood open! refrigerant R134a under pressure. Service
and repairs to the system should only be done
If there are any indications while driving that by an authorized workshop.
the hood is not completely closed, stop imme-
diately and close it securely.
Related information
Related information • Volvo's service program (p. 576)
• Engine compartment overview (p. 587)
• Door and seat belt reminders (p. 51)
586 * Option/accessory.
MAINTENANCE AND SERVICE
WARNING
The ignition system works with extremely high
and dangerous voltages. The vehicle electrical
system should always be in ignition mode 0
The layout of the engine compartment may vary depend- when work in being performed in the engine
ing on model and engine variant. compartment.
Volvo recommends:
Coolant expansion tank Do not touch any spark plugs or ignition coils
when the vehicle electrical system is in igni-
Brake fluid reservoir (located on the driver's tion mode II or when the engine is warm.
side)
Washer fluid filler pipe11 Related information
• Opening and closing the hood (p. 585)
Fusebox
• Filling washer fluid (p. 632)
Air filter • Refilling coolant (p. 590)
Engine oil filler pipe • Fuses in the engine compartment (p. 605)
• Checking and filling engine oil (p. 588)
• Ignition modes (p. 407)
587
MAINTENANCE AND SERVICE
|| If the engine oil is not checked regularly and the warning symbol is displayed in the instrument Checking and filling engine oil
level becomes low, this could cause serious panel when oil pressure is low . On engine The engine oil level is monitored by an electronic
engine damage. variants with an oil level sensor, the warn- oil level sensor.
ing symbol in the instrument panel and display
CAUTION messages are used to alert the driver. Some
To satisfy the requirements for the engine's engine variants have both systems. Contact a
service intervals, all engines are factory-filled Volvo retailer for more information.
with a specially adapted synthetic engine oil. Change the engine oil and oil filter according to
Great care has been put into the choice of oil, the schedule specified in the Warranty and Main-
with consideration given to service life, starta- tenance Records Information booklet. Oils of a
bility, fuel consumption and environmental higher grade than that specified may be used. If
impact. the vehicle is driven in adverse conditions, Volvo
For the recommended service intervals to recommends using an oil with a higher grade
apply, an approved engine oil must be used. than that specified.
Only use the prescribed oil grade to top off or
Related information
change the oil. Otherwise, there is a risk of
the vehicle's service life, startability, fuel con- • Checking and filling engine oil (p. 588)
sumption and environmental impact being • Engine oil specifications (p. 644)
affected.
Failure to use engine oil of the prescribed
grade and viscosity could cause damage to
engine-related components. Volvo Car Corpo-
ration disclaims warranty liability for such type
of damage.
Volvo recommends entrusting oil changes to
an authorized Volvo workshop.
588
MAINTENANCE AND SERVICE
CAUTION
If this symbol is shown together
with a message about low oil level,
for example Engine oil level low
Refill 1 liter, fill only with the indi-
cated volume, e.g. 1 liter (1 quart).
WARNING
Do not spill oil on the hot exhaust pipes as
this could cause a fire.
Filler pipe12. Oil level graphic in the center display.
Viewing oil level in the center display
It may be necessary to top up engine oil between
The oil level can be viewed using the electronic NOTE
regularly scheduled services.
oil level gauge in the center display once the
No action is necessary with regard to engine oil vehicle has been started. The oil level should be The system cannot directly detect changes
level until a message appears in the instrument checked regularly. when the oil is filled or drained. The vehicle
panel. must have been driven approximately 30 km
(20 miles) and have been stationary
5 minutes on a level surface and with the
WARNING engine off before the correct oil level will be
If this symbol is shown together displayed.
with the message Engine oil level
Service required, visit a workshop
– an authorized Volvo workshop is
recommended. The oil level may be too high. 1. Open the Car status app from App view in
the center display.
2. Tap Status to display the oil level.
589
MAINTENANCE AND SERVICE
WARNING
The coolant may be very hot. Never unscrew
the cap when the coolant is hot. If coolant
must be filled, unscrew the expansion tank
cap slowly to relieve overpressure.
590
MAINTENANCE AND SERVICE
591
MAINTENANCE AND SERVICE
|| If you are experiencing problems with any lights NOTE • Replacing front turn signal bulbs (p. 597)
other than light bulbs, contact a workshop14. If • Bulb specifications (p. 597)
there is a problem with an LED13 light, the entire Exterior lighting such as headlights and tail-
lamp unit will normally need to be replaced. lights may develop temporary condensation
on the inside of the lens. This is normal. All
exterior lighting is designed to resist this.
WARNING Condensation is normally vented out of the
The vehicle electrical system must be in igni- lamp housing once the light has been lit for
tion mode 0 when bulbs are replaced. some period of time.
CAUTION NOTE
Never touch the bulb glass with your bare fin- Bulbs for active curve lighting* contain traces
gers. Grease and oils from your fingers vapor- of mercury and should therefore always be
ize in the heat and will leave a deposit on the submitted to a certified Volvo service techni-
reflector, which may damage it. cian.
592 * Option/accessory.
MAINTENANCE AND SERVICE
Removing the plastic cover to Put the cover back in place in the reverse order. Removing the rectangular headlight
replace bulbs cover
Related information
The headlight bulbs can be replaced without the Most of the bulbs in the headlight housing can
assistance of a workshop, but before a bulb can
• Replacing bulbs (p. 591)
be accessed when the rectangular cover is
be replaced, the plastic cover over the headlight • Replacing the low beam headlight bulbs removed.
needs to be removed. (p. 595)
Before the rectangular cover can be removed, the
• Replacing the high beam headlight bulbs
plastic covering over the headlight must be
(p. 595)
removed.
• Replacing daytime running lights/front park-
ing light bulbs (p. 596)
• Replacing front turn signal bulbs (p. 597)
• Bulb specifications (p. 597)
Left headlight.
1. Undo the four screws of the cover using a
Torx tool, dimension T20 (1). Do not undo
these completely; 3–4 turns is enough.
Lift the rubber strip by pressing it inward into Push the cover to the side.
the engine compartment.
3. Remove the cover.
Release the pins in the plastic cover's four
clips by pressing them down with a screw- Put the cover back in place in the reverse order.
driver or similar object and remove the cover-
ing.
}}
593
MAINTENANCE AND SERVICE
Backup light16
Parking light (LED)
594 * Option/accessory.
MAINTENANCE AND SERVICE
Replacing the low beam headlight 4. Insert the new bulb in the socket. The bulb's Replacing the high beam headlight
bulbs guiding pin should point straight up. bulbs
The low beam bulbs in the halogen headlights 5. Press the connector into place. The high beam bulbs in the halogen headlights
can be changed without the help of a workshop. can be changed without the help of a workshop.
6. Put the round rubber cover back in place.
CAUTION Before the lamp can be replaced, the rectangular
Related information headlight cover must be removed.
Never touch the bulb glass with your bare fin- • Location of exterior lights (p. 594)
gers. Grease and oils from your fingers vapor- • Removing the plastic cover to replace bulbs CAUTION
ize in the heat and will leave a deposit on the (p. 593)
reflector, which may damage it. Never touch the bulb glass with your bare fin-
• Removing the rectangular headlight cover gers. Grease and oils from your fingers vapor-
(p. 593) ize in the heat and will leave a deposit on the
• Bulb specifications (p. 597) reflector, which may damage it.
Left headlight.
1. Remove the round low beam rubber cover
from the headlight housing.
Left headlight.
2. Remove the connector from the bulb.
1. Remove the bulb by turning the bulb holder
3. Remove the bulb by pressing it slightly upward and then pulling it straight out.
upward and then pulling it out.
2. Carefully pry the plastic sleeve by the con-
nector's locking lug to release it.
}}
595
MAINTENANCE AND SERVICE
|| 3. Remove the connector from the bulb. Replacing daytime running lights/
4. Replace the bulb. front parking light bulbs
The daytime running light/parking light bulbs in
5. Position the bulb in the socket and turn it the halogen headlights can be changed without
downward. the help of a workshop.
Related information Before the lamp can be replaced, the rectangular
• Location of exterior lights (p. 594) headlight cover must be removed.
• Removing the plastic cover to replace bulbs
(p. 593) NOTE
• Removing the rectangular headlight cover Daytime running lights/parking lights are eas-
(p. 593) ier to reach if the high beam headlight bulbs
Left headlight.
• Bulb specifications (p. 597) are removed. The high beam headlights are
mounted above and to the side of the daytime 1. Pull the daytime running light/parking light
running lights/parking lights. Remove the bulb holder straight out.
high beam headlight bulb by turning the bulb 2. Remove the bulb by pulling it straight out.
holder upward and then pulling it straight out.
3. Replace the bulb.
4. Position the bulb holder in the socket and
CAUTION
push it into place.
Never touch the bulb glass with your bare fin-
gers. Grease and oils from your fingers vapor- 5. If the high beam bulb holder has come loose,
ize in the heat and will leave a deposit on the position it in the socket and turn downward.
reflector, which may damage it. Related information
• Location of exterior lights (p. 594)
• Removing the plastic cover to replace bulbs
(p. 593)
• Removing the rectangular headlight cover
(p. 593)
• Bulb specifications (p. 597)
596
MAINTENANCE AND SERVICE
Replacing front turn signal bulbs • Removing the rectangular headlight cover Bulb specifications
The turn signal bulbs in the halogen headlights (p. 593) The following specifications apply to the bulbs in
can be changed without the help of a workshop. • Bulb specifications (p. 597) the halogen headlights.
Before the lamp can be replaced, the rectangular If you are experiencing problems with any other
headlight cover must be removed. lights, contact a workshop17.
Function WA Type
Related information
Left headlight. • Location of exterior lights (p. 594)
1. Press the retaining catches together and pull • Replacing bulbs (p. 591)
the bulb holder straight out.
2. The bulb holder and bulb must be replaced
as one unit.
3. Position the bulb holder in the socket and
push it into place.
Related information
• Location of exterior lights (p. 594)
• Removing the plastic cover to replace bulbs
(p. 593)
597
MAINTENANCE AND SERVICE
Start battery WARNING Use the vehicle's connection points in the engine
The vehicle has a single-pole electrical system compartment to connect an external start battery
that uses the chassis and engine mount as con- • Batteries generate hydrogen gas, which or battery charger.
is flammable and explosive.
ductors. The battery terminals on the car's starter battery
The start battery is used to start the electrical
• Do not connect the jumper cable to any in the luggage/cargo area must not be used.
part of the fuel system or to any moving
system and power the starter motor and other parts. Avoid touching hot manifolds. If the start battery is being charged, the support
electrical equipment in the vehicle. battery will also be charged.
• Battery fluid contains sulfuric acid. Do not
The start battery should only be replaced by a allow battery fluid to contact eyes, skin,
workshop18. fabrics or painted surfaces.
The vehicle has a voltage-regulated alternating • If contact occurs, flush the affected area
current generator. immediately with water. Obtain medical
help immediately if eyes are affected.
The starter battery is a 12 V battery, designed for
the carbon dioxide reducing functions Start/Stop • Never expose the battery to open flame
and regenerative charging, and to support the or electric spark. Do not smoke near the
functionality of the car's different systems. battery. Failure to follow the instructions
for jump starting can lead to injury.
The service life and performance of the start bat-
tery are affected by factors such as driving style,
driving conditions, climate, battery discharges, Connection points
number of starts, etc. Positive connection point
WARNING
• Never disconnect the start battery while the Negative connection point
engine is running. PROPOSITION 65 WARNING
• Make sure the cables to the start battery are Battery posts, terminals, and related accesso-
correctly connected and the clamps are ries contain lead and lead compounds, chemi-
securely tightened. cals known to the state of California to cause
cancer and reproductive harm. Wash hands
after handling.
598
MAINTENANCE AND SERVICE
Specifications
Battery H7 AGM H8 AGM
Voltage (V) 12 12
}}
599
MAINTENANCE AND SERVICE
Volvo recommends that batteries are replaced by • Jump starting using another battery (p. 447)
an authorized Volvo workshop.
CAUTION
When replacing the starter battery or support
battery, an AGM19 battery must be installed.
CAUTION
If replacing the starter battery, make sure you
replace it with a battery with the same cold
start capacity and type as the original battery
(see the decal on the battery).
NOTE
The size of the starter battery should conform
to the dimensions of the original battery.
Related information
• Battery symbols (p. 602)
• Support battery (p. 601)
600
MAINTENANCE AND SERVICE
}}
601
MAINTENANCE AND SERVICE
602
MAINTENANCE AND SERVICE
603
MAINTENANCE AND SERVICE
WARNING
Never use a foreign object or a fuse with a
higher amperage than that specified to
replace a fuse. This could cause significant
damage to the electrical system and possibly
lead to a fire.
WARNING
Contact an authorized Volvo workshop for
assistance replacing fuses not listed in the
Owner's Manual. If performed incorrectly, sig-
nificant damage can be caused to the electri-
cal system.
Related information
• Fuses and fuseboxes (p. 603)
• Fuses in the cargo compartment (p. 611)
604
MAINTENANCE AND SERVICE
}}
605
MAINTENANCE AND SERVICE
|| Fuse pliers are provided on the inside of the fuse Function AA Function AA
box cover to assist in removing and inserting
fuses. Vacuum regulators; valve; valve 7.5 Starter motor Shunt
There are also spaces for several extra fuses in for power pulse (diesel)
Fuel filter heater (diesel) 30
the fusebox. Engine control module; actuator; 20
throttle unit; EGR valve (diesel); – –
Positions
turbo position sensor (diesel);
There is a decal with a diagram of the locations – –
turbocharger valve (gasoline)
of the fuses on the inside of the cover.
Engine control module 5 – –
• Fuses 1-13, 18-30, 35-37 and 46-54 are
"Micro" fuses.
– – – –
• Fuses 14-17, 31-34 and 38-45 are
"MCase" fuses and should only be replaced Solenoids (gasoline); valve; 10 – –
by a workshop21. Engine cooling system thermo-
stat (gasoline); EGR cooling – –
Function AA pump (diesel); glow control
module (diesel) – –
– –
Spoiler shutter control module; 5 12 V outlet in tunnel console, 15
– – Radiator shutter control module; front
Relay windings for power pulse
– – 12 V outlet in tunnel console 15
(diesel)
between rear seats
Ignition coils (gasoline); spark 15 Heated oxygen sensor, front; 15
plugs (gasoline) 12 V outlet in trunk/cargo com- 15
Heated oxygen sensor, rear
partment*
Oil pump solenoid; A/C mag- 15 (gasoline)
netic coupling; heated oxygen – –
Engine control module 20
sensor, center (gasoline); heated
oxygen sensor, rear (diesel) – –
Starter motor 40
– –
606 * Option/accessory.
MAINTENANCE AND SERVICE
– – A Ampere
B LED (Light Emitting Diode)
* Option/accessory. 607
MAINTENANCE AND SERVICE
608
MAINTENANCE AND SERVICE
Fuse pliers are provided on the inside of the fuse Function Function
AA AA
box cover to assist in removing and inserting
fuses. – – Instrument lighting; Interior lighting; 7.5
There are also spaces for several extra fuses in Rearview mirror auto-dim function*;
– – Rain and light sensors*; Rear tun-
the distribution box in the engine compart-
ment. nel console keypad, rear seat*;
Steering wheel module 5
Power front seats*; Rear door con-
Positions Module for start knob and parking 5 trol panels; Climate system blower
• Fuses 1, 3-21, 23-36, 39-53 and 55-59 are brake controls module left/right
"Micro" fuses.
Heated steering wheel* module 15 Control module for driver support 5
• Fuses 2-22, 37-38 and 54 are "MCase" functions
fuses and should only be replaced by a work-
– –
shop22. Panoramic roof with sun curtain* 20
– –
Function AA Head-up display* 5
– – – –
Passenger compartment lighting 5
* Option/accessory. 609
MAINTENANCE AND SERVICE
|| Function AA Function AA
Control module for Internet-con- 5 Door module in left-side front door 20
nected vehicle; Control module for
Volvo On Call Active chassis control module* 20
Coolant pump 10
– –
610 * Option/accessory.
MAINTENANCE AND SERVICE
}}
* Option/accessory. 611
MAINTENANCE AND SERVICE
||
The fuse box is located under the storage compartment on the right-hand side.
Fuse pliers are provided on the inside of the fuse There are also spaces for several extra fuses in
box cover to assist in removing and inserting the distribution box in the engine compart-
fuses. ment.
612
MAINTENANCE AND SERVICE
* Option/accessory. 613
MAINTENANCE AND SERVICE
|| Related information
• Fuses and fuseboxes (p. 603)
• Replacing fuses (p. 604)
614
MAINTENANCE AND SERVICE
Cleaning the interior • Cleaning floor mats and inlay mats (p. 617) Cleaning the center display
Only use cleaning agents and car care products • Cleaning leather upholstery (p. 618) Marks, stains, finger smudges etc. on the center
recommended by Volvo. Clean regularly and display may affect its performance and readabil-
• Cleaning the leather steering wheel
treat stains immediately for best results. It is (p. 619) ity. Clean the screen regularly with a microfiber
important to vacuum before using a cleaning cloth.
agent. • Cleaning interior plastic, metal and wood sur-
faces (p. 620)
CAUTION
• Some colored clothing (for example, dark
jeans and suede garments) may stain the
upholstery. If this occurs, it is important to
clean and treat these parts of the uphols-
tery as soon as possible.
• Never use strong solvents such as
washer fluid, gasoline, mineral spirit or
concentrated alcohol to clean the interior
as this can damage the upholstery as
well as other interior materials.
To clean the center display:
• Never spray cleaning agent directly onto
components that have electrical buttons 1. Turn off the center display by pressing and
and controls. Wipe instead with a damp holding the Home button.
cloth with cleaning agent. 2. Wipe the screen clean with the microfiber
• Sharp objects and Velcro can damage cloth provided or use another microfiber
the car's textile upholstery. cloth of similar quality. Wipe the screen with
a clean, dry microfiber cloth using small, cir-
cular motions. If necessary, moisten the cloth
Related information
slightly.
• Cleaning the center display (p. 615)
3. Reactivate the display by pressing the Home
• Cleaning fabric upholstery and ceiling liner
button briefly.
(p. 617)
• Cleaning the seat belt (p. 617)
}}
615
MAINTENANCE AND SERVICE
|| CAUTION • Cleaning the leather steering wheel Cleaning the head-up display*
(p. 619) Carefully wipe the glass covering the head-up
The microfiber cloth must be free of sand and
dirt when cleaning the center display. • Cleaning interior plastic, metal and wood sur- display unit with a clean and dry microfiber cloth.
faces (p. 620) If necessary, the cloth may be slightly moistened.
Related information
• Cleaning the interior (p. 615)
• Cleaning fabric upholstery and ceiling liner
(p. 617)
• Cleaning the seat belt (p. 617)
• Cleaning floor mats and inlay mats (p. 617)
• Cleaning leather upholstery (p. 618)
616 * Option/accessory.
MAINTENANCE AND SERVICE
Cleaning fabric upholstery and Cleaning the seat belt Cleaning floor mats and inlay mats
ceiling liner Only use cleaning agents and car care products Only use cleaning agents and car care products
Only use cleaning agents and car care products recommended by Volvo. Clean regularly and recommended by Volvo. Clean regularly and
recommended by Volvo. Clean regularly and treat stains immediately for best results. It is treat stains immediately for best results. It is
treat stains immediately for best results. It is important to vacuum before using a cleaning important to vacuum before using a cleaning
important to vacuum before using a cleaning agent. agent.
agent.
Seat belts Inlay mats and floor mats
Fabric upholstery and ceiling liner Use water and a synthetic soap solution. Spe- Remove the inlay mats to clean the floor mats
Never scrape or rub a stain, as this could damage cially designed textile cleaning agents are availa- and inlay mats separately. Use a vacuum to
the upholstery. Never use strong stain removers, ble for purchase at Volvo retailers. Make sure the remove dust and dirt. Each inlay mat is secured
as this could change the color of the upholstery. belt is dry before it is retracted. into place with pins.
Use soapy water or a similar detergent. For more Related information Remove the inlay mat by grasping the inlay mat
difficult stains caused by oil, ice cream, shoe pol- at each pin and lifting the mat straight up.
• Cleaning the interior (p. 615)
ish, etc., use a stain remover. Consult with your Put the inlay mat back into place by pressing it in
Volvo retailer. • Cleaning the center display (p. 615)
at each pin.
• Cleaning fabric upholstery and ceiling liner
Related information (p. 617)
• Cleaning the interior (p. 615)
• Cleaning floor mats and inlay mats (p. 617)
• Cleaning the center display (p. 615)
• Cleaning leather upholstery (p. 618)
• Cleaning the seat belt (p. 617)
• Cleaning the leather steering wheel
• Cleaning floor mats and inlay mats (p. 617) (p. 619)
• Cleaning leather upholstery (p. 618) • Cleaning interior plastic, metal and wood sur-
• Cleaning the leather steering wheel faces (p. 620)
(p. 619)
• Cleaning interior plastic, metal and wood sur-
faces (p. 620)
}}
617
MAINTENANCE AND SERVICE
618 * Option/accessory.
MAINTENANCE AND SERVICE
Cleaning the leather upholstery Cleaning the leather steering wheel Type 3(dry dirt or dust)
1. Apply the leather cleaner to a damp sponge Only use cleaning agents and car care products 1. Remove the dirt/dust using a soft brush.
and squeeze it until the cleaner foams. recommended by Volvo. Clean regularly and
treat stains immediately for best results. It is 2. Same procedure as for Type 1 stains.
2. Move the sponge in circular motions to apply
the foam to the stain. important to vacuum before using a cleaning Related information
agent.
3. Dampen the stain thoroughly with the • Cleaning the interior (p. 615)
sponge. Let the sponge absorb the stain and Leather steering wheel • Cleaning the center display (p. 615)
do not rub. Leather needs to breathe. Never cover the • Cleaning fabric upholstery and ceiling liner
4. Dry the stain using a soft towel and let the leather steering wheel with a plastic protector. (p. 617)
leather dry completely. Volvo Leather Care Kit 951 0251 and Leather
Softener 943 7429 are recommended for clean- • Cleaning the seat belt (p. 617)
Protecting the leather upholstery ing the leather steering wheel. First, remove dirt, • Cleaning floor mats and inlay mats (p. 617)
1. Apply a small amount of leather protector to dust, etc. with a damp sponge or cloth.
a cloth and then apply the protector to the
• Cleaning leather upholstery (p. 618)
leather using light circular movements. • Cleaning interior plastic, metal and wood sur-
CAUTION faces (p. 620)
2. Let it dry for approximately 20 minutes.
Sharp objects such as rings could damage
Protecting the leather upholstery makes it better the leather on the steering wheel.
able to withstand sunlight's harmful UV rays.
619
MAINTENANCE AND SERVICE
Cleaning interior plastic, metal and • Cleaning fabric upholstery and ceiling liner Cleaning the exterior
wood surfaces (p. 617) The vehicle should be washed as soon as it
Only use cleaning agents and car care products • Cleaning the seat belt (p. 617) becomes dirty. This makes the vehicle easier to
recommended by Volvo. Clean regularly and clean because dirt does not attach as strongly. It
• Cleaning floor mats and inlay mats (p. 617)
treat stains immediately for best results. also reduces the risk of scratches and keeps the
• Cleaning leather upholstery (p. 618) vehicle looking new. Wash the vehicle in a car
Interior plastic, metal and wood • Cleaning the leather steering wheel (p. 619) wash or garage with an oil separator. Use a car
surfaces washing detergent.
A lightly dampened microfiber cloth is recom-
mended for cleaning interior details and surfaces. Related information
These cloths are available for purchase at Volvo • Cleaning the exterior (p. 620)
retailers. • Polishing and waxing (p. 621)
Never scrape or rub a stain. Never use strong • Hand washing (p. 621)
stain removers.
• Automatic car washes (p. 623)
CAUTION
• High-pressure washing (p. 624)
• Cleaning the wiper blades (p. 624)
Do not use solvent containing alcohol to
clean the instrument panel glass. • Cleaning exterior plastic, rubber and trim
components (p. 625)
• Cleaning rims (p. 626)
CAUTION
• Corrosion protection (p. 626)
Keep in mind that glossy surfaces can be
easily scratched. Wipe these surfaces with a
clean and dry microfiber cloth using small, cir-
cular motions. If necessary, moisten the cloth
lightly with clean water.
Related information
• Cleaning the interior (p. 615)
• Cleaning the center display (p. 615)
620
MAINTENANCE AND SERVICE
621
MAINTENANCE AND SERVICE
|| • Wash using a sponge, car washing detergent NOTE • Cleaning the wiper blades (p. 624)
and plenty of lukewarm water. • Cleaning exterior plastic, rubber and trim
Exterior lighting such as headlights and tail-
• Clean the wiper blades with lukewarm soap
lights may develop temporary condensation
components (p. 625)
solution or car washing detergent. • Cleaning rims (p. 626)
on the inside of the lens. This is normal. All
• Dry the vehicle using a clean, soft chamois or exterior lighting is designed to resist this. • Corrosion protection (p. 626)
a squeegee. Try not to let drops of water dry Condensation is normally vented out of the
in strong sunlight. This could cause water lamp housing once the light has been lit for
drying stains that may need to be polished some period of time.
out.
• In areas with heavy industrial emissions,
CAUTION
more frequent washing of the vehicle's exte-
rior is recommended. • Make sure that the panoramic roof and
sun shade are closed before washing the
• Tar spots from asphalt may remain even after
washing. Use a tar remover to remove these vehicle.
spots after washing the vehicle. • Never use abrasive polishing agents on
the panoramic roof.
WARNING • Never use wax on the rubber seals
Always entrust engine washing to a workshop. around the panoramic roof.
If the engine is hot, there is a risk of fire.
CAUTION
CAUTION Remember to remove dirt from the drain
Dirty headlights do not work as well. Clean holes in the doors and sills after washing the
them regularly, e.g. when refueling. vehicle.
Do not use corrosive cleaners. Use water and
a non-abrasive sponge. Related information
• Cleaning the exterior (p. 620)
• Polishing and waxing (p. 621)
• Automatic car washes (p. 623)
• High-pressure washing (p. 624)
622
MAINTENANCE AND SERVICE
623
MAINTENANCE AND SERVICE
High-pressure washing Cleaning the wiper blades • Cleaning rims (p. 626)
The vehicle should be washed as soon as it The vehicle should be washed as soon as it • Corrosion protection (p. 626)
becomes dirty. This makes the vehicle easier to becomes dirty. This makes the vehicle easier to
clean because dirt does not attach as strongly. It clean because dirt does not attach as strongly. It
also reduces the risk of scratches and keeps the also reduces the risk of scratches and keeps the
vehicle looking new. Wash the vehicle in a car vehicle looking new. Wash the vehicle in a car
wash or garage with an oil separator. Use a car wash or garage with an oil separator. Use a car
washing detergent. washing detergent.
624
MAINTENANCE AND SERVICE
* Option/accessory. 625
MAINTENANCE AND SERVICE
Cleaning rims Corrosion protection • Cleaning exterior plastic, rubber and trim
The vehicle should be washed as soon as it Your vehicle is constructed with effective protec- components (p. 625)
becomes dirty. This makes the vehicle easier to tion against corrosion. • Cleaning rims (p. 626)
clean because dirt does not attach as strongly. It
also reduces the risk of scratches and keeps the Corrosion protection for the body consists of
vehicle looking new. Wash the vehicle in a car modern metallic protective coatings on the sheet
wash or garage with an oil separator. Use a car metal, a high-quality painting process, corrosion-
washing detergent. protected and minimized metal overlap, and
shielding plastic components, abrasion protection
Rims and supplemental rust inhibitor in exposed areas.
Only use rim cleaning products recommended by In the chassis, exposed components of the wheel
Volvo. suspension are made of corrosion-resistant cast
aluminum.
Strong rim cleaning agents could damage the
surface and stain the chromed aluminum rims. Inspection and maintenance
The corrosion protection does not normally
Related information
require maintenance, but keeping the vehicle
• Cleaning the exterior (p. 620)
clean is always a good way to further reduce the
• Polishing and waxing (p. 621) risk of corrosion. The use of strong alkaline or
• Hand washing (p. 621) acidic cleaning fluids should always be avoided
on shiny body components. Any stone chips in
• Automatic car washes (p. 623)
the paint should be touched up as soon as they
• High-pressure washing (p. 624) are discovered.
• Cleaning exterior plastic, rubber and trim
components (p. 625) Related information
• Cleaning the exterior (p. 620)
• Cleaning rims (p. 626)
• Polishing and waxing (p. 621)
• Corrosion protection (p. 626)
• Hand washing (p. 621)
• Automatic car washes (p. 623)
• High-pressure washing (p. 624)
• Cleaning the wiper blades (p. 624)
626
MAINTENANCE AND SERVICE
Paintwork Touching up minor paint damage If the damage has not reached all the way down
The paintwork consists of multiple layers. It is an The paintwork is an important part of the vehi- to the metal, then touch-up paint can be applied
important part of the vehicle's corrosion protec- cle's corrosion protection and therefore needs immediately after the surface has been cleaned.
tion and therefore needs to be checked regu- to be checked regularly. The most common
larly. types of paint damage are minor stone chips, NOTE
scratches and damage to e.g. the edges of Make sure the surface is clean and dry before
The most common types of paint damage are fenders, doors and bumpers.
minor stone chips, scratches and damage to e.g. performing any touch-ups to the paint. The
the edges of fenders, doors and bumpers. To When repairing paint damage, the vehicle must surface temperature should be at least 15 °C
help prevent corrosion, paint damage should be be clean, dry and have a temperature above (60 °F).
rectified immediately. 15 °C (60 °F).
NOTE
When repairing paintwork, it must be clean,
dry and at a temperature of at least 15°C.
24 If required.
25 Follow the instructions on the packaging for the touch-up pen/stick carefully. }}
627
MAINTENANCE AND SERVICE
|| 1. Place a strip of masking tape over the dam- Related information Color codes
aged surface. Pull the tape off so that any • Paintwork (p. 627)
loose flakes of paint adhere to it. Color code
• Color codes (p. 628)
The color code label is located on the left door
If the damage goes down to the bare metal,
pillar and is visible when the left front door is
you may need to use primer first. If the paint
opened.
damage is on a plastic surface, an adhesive
primer should be used for better results.
Spray the primer into the lid of the spray can
and brush on thinly.
2. Light sanding with a very fine-grained sand-
paper or similar may be required before
painting (e.g. if there are uneven edges).
Clean the area carefully and let it dry.
3. Thoroughly mix the primer and apply it with a
small brush, toothpick or similar. When the
primer is dry, apply one or more coats of
paint and then a clear coat, letting the paint
dry between each application. Sample color code (1): US models.
If there is a longer scratch, follow the same pro-
cedure as above, but first mask off the surround-
ing area to protect the undamaged paint.
Touch-up pens and spray paints are available at
Volvo retailers.
NOTE
If the stone chip has not gone down to the
bare metal and an undamaged coat of paint
remains, apply base coat and clear coat
immediately after cleaning the surface.
Sample color code (1): Canadian models.
628
MAINTENANCE AND SERVICE
It is important to use the right color. Changing rear window wipers 1. Grasp the center of the wiper blade and
The wiper blades help remove water from the lift it from the window to the stop position.
Related information
windshield and rear window. Along with the
• Paintwork (p. 627)
washer fluid, they clean the glass and help NOTE
• Touching up minor paint damage (p. 627) improve visibility while driving. The windshield
and rear window wiper blades can be replaced. When the wiper arm is halfway folded out, it
will stop in a locking position that helps pre-
Changing rear window wipers vent the arm from falling back onto the rear
window. The wiper arm must be pulled past
the locking position stop in order to change
the wiper blade.
Related information
• Using the rain sensor (p. 181)
• Using the windshield and headlight washers
(p. 183)
• Using automatic rear window wiping when
backing up (p. 185)
}}
629
MAINTENANCE AND SERVICE
• Heated windshield washer nozzles* (p. 181) Replacing windshield wiper blades Raise the wiper arms to the service position.
Service position is activated/deactivated via
• Using the rain sensor's memory function The wiper blades help remove water from the
(p. 182) windshield and rear window. Along with the the function view in the center display when
washer fluid, they clean the glass and help the car is stationary and the windshield wip-
• Using the rear window wiper/washer
improve visibility while driving. The windshield ers are not on. Press the button on the wiper
(p. 184) blade attachment and pull the wiper blade
and rear window wiper blades can be replaced.
• Filling washer fluid (p. 632) straight out, parallel with the wiper arm.
• Windshield wipers in the service position Replacing wiper blades Slide in a new wiper blade until it clicks into
(p. 631) place.
• Replacing windshield wiper blades (p. 630) 3. Check to make sure the blade is securely in
• Using the windshield wipers (p. 180) place.
4. Press the wiper blade back against the wind-
shield.
630 * Option/accessory.
MAINTENANCE AND SERVICE
}}
* Option/accessory. 631
MAINTENANCE AND SERVICE
|| The wiper blades will also move out of service • Changing rear window wipers (p. 629) Filling washer fluid
position if: • Using the windshield wipers (p. 180) Washer fluid is used to keep the headlights,
• The windshield wipers are turned on. windshield and rear window clean. Washer fluid
containing anti-freeze should be used in very
• The windshield washers are turned on.
cold weather (below-freezing temperatures).
• The rain sensor is activated.
• The vehicle begins moving.
CAUTION
If the wiper arms in service position are raised
from the windshield, they must be folded back
against the windscreen before activating wip-
ing, washing or rain sensor as well as before
departure. This is to prevent scratching the
paint on the hood.
Related information
• Using the rain sensor (p. 181)
Fill washer fluid into the reservoir with the blue
• Using the windshield and headlight washers
cover. The reservoir is used for the windshield
(p. 183)
washer, tailgate window washer and headlight
• Using automatic rear window wiping when washer*
backing up (p. 185)
• Heated windshield washer nozzles* (p. 181) NOTE
• Using the rain sensor's memory function When there is approximately 1 liter (1 qt) of
(p. 182) washer fluid remaining, the message Washer
• Using the rear window wiper/washer fluid Level low, refill and the symbol
(p. 184) will be displayed in the instrument panel.
• Filling washer fluid (p. 632)
• Replacing windshield wiper blades (p. 630)
632 * Option/accessory.
MAINTENANCE AND SERVICE
Recommended grade: Washer fluid recom- • Heated windshield washer nozzles* (p. 181)
mended by Volvo, with frost protection during
• Using the rain sensor's memory function
cold weather and temperatures below the freez- (p. 182)
ing point.
• Using the rear window wiper/washer
(p. 184)
CAUTION
• Windshield wipers in the service position
Use Volvo's original washer fluid or an equiva- (p. 631)
lent fluid with the recommended pH value
between 6 and 8, diluted as recommended, • Replacing windshield wiper blades (p. 630)
e.g. in a 1:1 solution with pH-neutral water. • Changing rear window wipers (p. 629)
• Using the windshield wipers (p. 180)
CAUTION
Use washer fluid with anti-freeze when tem-
peratures are below the freezing point to help
keep the pump, reservoir and hoses from
freezing.
Volume:
• Vehicles with headlight washing: 5.5 liters
(5.8 qts).
• Vehicles without headlight washing: 3.5 lit-
ers (3.7 qts).
Related information
• Using the rain sensor (p. 181)
• Using the windshield and headlight washers
(p. 183)
• Using automatic rear window wiping when
backing up (p. 185)
* Option/accessory. 633
SPECIFICATIONS
SPECIFICATIONS
Type designations
The decals in the vehicle contain information
such as chassis number, type designation, color
code, etc.
Location of decals
The illustration is general and details may vary depending on market and model.
636
SPECIFICATIONS
Vehicle Emission Control Information. US Vehicle Identification Number (VIN). The Federal Motor Vehicle Safety Standards
models. Your Volvo is designed to meet all appli- VIN plate is located on the top left surface of the (FMVSS) specifications (USA) and Ministry of
cable emission standards, as evidenced by the dashboard. The Vehicle Identification Number Transport (CMVSS) standards (Canada). Your
certification label on the underside of the hood. (VIN) should always be quoted in all correspond- Volvo is designed to meet all applicable safety
For further information regarding these regula- ence concerning your vehicle with the retailer and standards, as evidenced by the certification label
tions, please consult your Volvo retailer. when ordering parts. on the driver's side B-pillar (the structural mem-
ber at the side of the vehicle, at the rear of the
driver's door opening). This label also includes
codes for paint color, etc. For further information
regarding these regulations, please consult your
Volvo retailer. U.S. models have the upper decal;
Canadian models have the lower one.
Vehicle Emission Control Information. Tire inflation pressures. This label indicates
Canadian models. Your Volvo is designed to the correct inflation pressures for the tires that
meet all applicable emission standards, as evi- were on the vehicle when it left the factory.
denced by the certification label on the underside
of the hood. For further information regarding
these regulations, please consult your Volvo
retailer.
}}
637
SPECIFICATIONS
|| Related information
• Air conditioning specifications (p. 646)
NOTE
The decals shown in the Owner's Manual do
not claim to be exact reproductions of those
found in the vehicle. The purpose is to show
approximately how they look and about where
they are located on the vehicle. The informa-
tion that applies for your vehicle in particular
is found on the decal on the vehicle.
638
SPECIFICATIONS
Dimensions
The vehicle's length, height, etc. are shown in
the table.
C Length 4950 194.9 H Wheel track, frontE 1665F 65.6F Wheel track, rearH 1671F 65.8F
D Load length, floor, 2040 80.3 1673G 65.9G 1679G 66.1G
folded backrest
1260B 49.6B Wheel track, frontH 1668F 65.7F J Load width, floor 1192 46.9
E Load length, floor 1220C 48.0C 1676G 66.0G
554D 21.8D
}}
* Option/accessory. 639
SPECIFICATIONS
|| Dimensions mm inches
K Width 1923I 75.7I
1931J 76.0J
1958K 77.1K
L Width incl. rearview 2140 84.3
mirrors
M Width incl. folded rear- 2008 79.1
view mirrors
A At curb weight + 2 people. Varies slightly depending on tire
dimensions, chassis, etc.)
B From the second row of seats in 7-seat models.*
C Vehicles with 5 seats.
D Vehicles with 7 seats.
E Vehicles without pneumatic suspension.
F Vehicles with 18 and 19-inch wheels.
G Vehicles with 20, 21 and 22-inch wheels.
H Vehicles with pneumatic suspension.
I Chassis width.
J Width for vehicles with 18 and 19-inch wheels.
K Width for vehicles with 20, 21 and 22-inch wheels.
Related information
• Weights (p. 641)
640
SPECIFICATIONS
Weights
The following table lists important weight data
for your vehicle.
Category USA Canada
(lbs) (kg)
7-seat, AWD (All Wheel Drive) 6060 2750
Gross vehicle weight
Other models 6005 2725
7-seat 1210 550
Capacity weight
Other models 1100 500
7-seat, AWD (All Wheel Drive) 2885 1310
Permissible axle weights, front
Other models 2865 1300
Permissible axle weights, rear 3280 1490
7-seat 4430–4650 2040–2140
Curb weight
5-seat 4270–4520 2000–2080
Max. roof load 220 100
641
SPECIFICATIONS
Towing capacity and tongue weight Towing capacity and tongue weight are shown
in the tables below.
• The maximum trailer weights listed are • Trailer Stability Assist* (p. 451)
only applicable for altitudes up to 3280 ft
(1,000 m) above sea level. With increas-
ing altitude the engine power and there-
fore the car's climbing ability are impaired
because of the reduced air density, so
the maximum trailer weight has to be
reduced accordingly. The weight of the
car and trailer must be reduced by 10%
for every further 3280 ft (1,000 m) (or
part thereof).
Related information
• Type designations (p. 636)
• Weights (p. 641)
642 * Option/accessory.
SPECIFICATIONS
Related information
• Type designations (p. 636)
• Engine oil specifications (p. 644)
• Coolant specifications (p. 645)
643
SPECIFICATIONS
Viscosity chart
Extreme driving conditions
General Volvo's VCC RBS0-2AE/SAE 0W20 oil is recom-
See the Service and warranty booklet for infor-
mended for extreme conditions.
mation about oil change intervals.
Oil volume
NOTE The oil volume for the engine is:
This vehicle is delivered from the factory with
Liter (approx.) 5.6
synthetic oil.
US qts (approx.) 5.9
Do not use oil additives.
Related information
• Type designations (p. 636)
• Checking and filling engine oil (p. 588)
644
SPECIFICATIONS
Related information
• Engine compartment overview (p. 587)
645
SPECIFICATIONS
Evaporator
CAUTION
The A/C system evaporator must never be
repaired or replaced with a previously used
evaporator. The new evaporator must be certi-
fied and labeled in accordance with SAE
Refrigerant J2842.
Vehicles with R134a refrigerant
Weight Prescribed grade Related information
• Climate control system service (p. 586)
750 g (1.65 lbs) R134a
1000 gA (2.20 lbsA)
A Vehicles with A/C for the third row of seats*.
646 * Option/accessory.
SPECIFICATIONS
Approved tire pressure tion placard for information specific to the tires
The following tire pressures are recommended installed on your vehicle at the factory.
by Volvo for your vehicle. Refer to the tire infla-
Tire dimensions Cold tire pressure for up to seven people (depending on number of seats)
Front Rear
psi (kPa) psi (kPa)
235/60 R18 38 (260) 38 (260)
235/55 R19
275/45 R20
275/40 R21
275/35 R22
Temporary spare tire 60 (420) 60 (420)
T125/80 R18
Related information
• Type designations (p. 636)
• Checking tire pressure (p. 535)
647
INDEX INDEX
649
INDEX
650
INDEX
651
INDEX
Data sharing 514 Driver Alert Control limitations 362 Electrical system 598
Daytime running lights 156 Driver performance 92, 93 Electric parking brake 411
652
INDEX
653
INDEX
654
INDEX
655
INDEX
656
INDEX
Parking Assist 379, 380, 381, 382, 383 Pilot Assist 309, 312, 313, 314, 315,
P function 379, 380, 381 317, 319, 320, 321, 322
Paddle at steering wheel 203 Parking brake 411 pass 319
Paint activate and deactivate 412 pinch protection 170
color code 628 automatic activation 413 resetting 171
paint damage and touch-up 627, 628 Low battery charge level 414 PIN code 511
Panoramic roof Passenger compartment filter 211 Polishing 621
opening and closing 177 Passenger compartment interior 558 Position lights 156
pinch protection 170 center console 559
sun shade 176, 179 Power 643
electrical outlet 560
ventilation position 178 glove compartment 563 Power folding door mirrors 175
PAP – Park Assist Pilot 393, 394, 397, sun visor 564 Power panoramic roof 176
398, 400, 401 Passenger compartment lighting 165, 167 Power save mode 447
Park Assist Camera 384, 385, 386, 388, auto switch 165 Power seats 189
389, 391, 392 Passing assistance 302, 303, 319 Power tailgate 259
settings 389
personal information (Privacy Policy) 34 Power windows 171, 172
Park Assist Camera limitations 389
Phone 498 pinch protection 170
Park Assist Pilot 393, 394, 397, 398, changing to another 502 Pressure wash 624
400, 401 connect 499
function 393, 394, 398, 400, 401 Privacy Policy 34
connect automatically 501
limitations 398 connect manually 501 Private locking 264
operation 394, 397 delete 503 activation/deactivation 265
Symbols and messages 401 disconnect 502 PROPOSITION 65 WARNING 447
Park Assist Pilot – PAP 393, 394, 397, phone call 503, 505
398, 400, 401 text message 504
parking voice control 149
on hills 414
657
INDEX
658
INDEX
659
INDEX
Steel cargo grid 570 panoramic roof 176, 179 Temporary spare
pinch protection 170 spare tire 547
Steering assistance at risk of colli-
rear door 173 Temporary tire sealing system
sion 370, 371, 372, 373, 374, 375, 376, 378
Sun visor 564 execution, checking 551
Steering assistance at risk of rear-end col-
mirror lighting 166 Inflating tires 555
lision 375, 376
Support battery 601 location 550
Steering power level, see Steering wheel overview 550
resistance 270 Symbols
sealing compound 550
indicator symbols 95
Steering resistance at risk of head-on colli- Terms and conditions
sion 373, 374 Symbols and messages
services 34
Adaptive Cruise Control 307
Steering wheel 203 users 514
center display's status bar 126
heating 222, 223 Tire dimensions 532, 542
Collision warner with auto-brake 344
keypad 203
Symbols and messages for Assistance at Tire pressure decal 537
paddle 203
steering wheel adjustment 203 risk of collision 378 Tire pressure monitoring
system updates 579 calibrating 539
Steering wheel keypad 203
Tires 528
Steering wheel paddles 419
direction of rotation 530
Steering wheel resistance, speed-depend- glossary of terms 531
ent 270 T inflation pressure table 647
Stone chips and scratches 627, 628 Tailgate mounting 546
Stop/start function 428 locking/unlocking 241, 254 pressure 647
open/close with foot movement 263 removal 544
Storage compartments 558
power 259 rotation 529
center console 559
unlocking from inside 257 specifications 532, 647
glove compartment 563
Technician certification 37 storage 528
sun visor 564
tire pressure monitoring 537
660
INDEX
661
INDEX
662
TP 24829 (English – USA & Canada), AT 1746, MY18, Copyright © 2000-2017 Volvo Car Corporation