6ALS
3AL5
6AL5—3AL5—12AL5 taALs
Eta TWIN DIODE
DESCRIPTION AND RATING
‘The GALS is a miniature high-perveance twin diode in which separate
cathodes are provided for the two sections, The 6ALS is suited for a wide
variety of applications which include service as a detector in FM and tele-
vision circuits, automatic-gain-control rectifier, or a low-current power
BASING DIAGRAM
rectifier. Each diode can be used independently of the other or combined @
in parallel or full-wave arrangements, The resonant frequency of each section g S
of the 6ALS is approximately 700 megacycles.
‘The 3ALS, GALS and 12ALS are alike except for heater ratings and heater- =e
cathode voltage ratings. In addition, the 3ALS, as a result of its controlled Ad
heater warm-up characteristic, is suited for use in television receivers which
employ series-connected heaters. When the 3AL5 is used in conjunction with | 0
other 600-milliampere types which exhibit essentially the same heater warm-up
characteristic, heater voltage surges across the individual tubes are minimized
during the warm-up period.
RETMA GBT
GENERAL TERMINAL CONNECTIONS
in 1—Cathode (Section 1)
2—Plate (Section 2)
3—Heater
ELECTRICAL
Cathode—Coated Unipotential
SALS GALS 12AL5 amreetey (s 2
leater Voltage, - 3 5. colts Pes coiodeliseron
Heater Vohoge, AC or BC 33563126 oh Secs
loater Current... ; ou 15 Amperes | Pin 7—Plate (Section 1)
Heater Warm-up Time*......ceceeceee MO Seconds
With Without
Shieldt Shield
ct Interelectrode Capacitances
Plate-No. 1 to Cathode-No. 1, Heater, and Internal Shield... 3.2 25 uf
Plate-No. 2to Cathode-No.2, Heater, and Internal Shield... 3.2 25 uf PHYSICAL DIMENSIONS
Cathode-No. 1 to Plate-No. 1, Heater, and Internal Shield... 3.6 34 wf PS
Cathode-No. 2 to Plate-No. 2, Heater, and Internal Shield.... 3.6 3.4 uf a
Plate-No. 1 to Plate-No. 2, maximum... sees 110.026 0,068 yf a
MECHANICAL WN if
Mounting Position—Any b
Envelope—T-5172, Glass 1a | th
Base—E7-1, Miniature Button 7-Pin max.
GENERAL @ ELECTRIC sein
‘Supersedes £7-1269C date 1-80 and £1703 dete 12-496ALS
3ALS
12AL5
ET-1882
Page 2
ast
MAXIMUM RATINGS
DESIGN-CENTER VALUES
Peak Inverse Plate Voltage.......
AC Plate-Supply Voltage per Plate, RM:
Steady-State Peak Plate Current per Plate
DC Output Current per Plate. .
Heater-Cathode Voltage SALS
Heater Positive with Respect to Cathode
DC Component pao 5 - 100
Total DC and Peak ; 5 -200
Heater Negative with Respect to Cathode
: 200
Total DC and Peak.
CHARACTERISTICS AND TYPICAL OPERATION
HALF-WAVE RECTIFIER
AC Plate-Supply Voltage per Plate, RMS
Total Plote-Supply Resistance per Plate
DC Output Current per Plate
Tube Voltage Drop
1,=60 Milliomperes DC per Plate
-330
7
. 54
9.0 Milliamperes
GALS, 12AL5
Volts
330 Volts
330 Volts
117 Volts
300 Ohms
9.0 Milliamperes
= 10 Volts
* Heater warm-up time is defined as the time required in the
circuit shown at the right for the voltage across the heater
terminals to increase from zero to the heater test voltage &
(Vi). For this type, E=12.5 volts (RMS or DC), Vi=2.5 &
volts (RMS or DC), and R=15.8 ohms.
+ With extemal shield (RETMA 316) connected to pin 6,
Heater
}
of Tube
under
TestPLATE CURRENT 1 MILLIAUPERES.
70
60
10
“40
AVERAGE PLATE CHARACTERISTICS
KCK SecTION
Ey * RATED VALUE
i
PLATE VOLTAGE IM VOLTS
OPERATION CHARACTERISTICS
EACH SECTION
“24-20-18 ntk
DC VOLTAGE DEVELOPED BY DIODE IW VOLTS
“8
u
1
10
RECTIFIED CURRENT IN WILLIAMPERES.
6ALS
3ALS
T2AL5
ET-T882
3
Poses