Professional Documents
Culture Documents
( w. e. f. 01/09/2015) .
. ...
'·~
I
CURRENT SCHEDULE OF RATES 2015-2016
INDEX
I
10 BD-J-1 Repairs & Rehabilitation 34 --
1
11 Bd-K Expansion Joints
.
35 --
12 Bd-L Plastering and Pointing 36 41
13 Bd-M Paving , Flooring and Dado 42 53
14 Bd-N Wood Finish 54 55
15 Bd-0 Oil Painting 56 60
16 Bd-P Colour/White Washing , Distempering 61 63
17 Bd-Q Wood Work 64 67
18 Bd-R Roofing and Ceiling 68 79
--·------ --- - ------ -------- ----------- ~----- - - - --- - - --- --- - - ------ - -~--- -------------~--- - -~-~ ---
...
GENERAL NOTE
1) Shedule of rates prepared for the year 2015-16 is operative from 01 I 09 /2015 and
applicable for Nagpur, Chandrapur, Wardha, Bhandara, Gondia & Gadchiroli districts.
2) For the rates in notified Tribal areas, Hilly and in accessible areas, corporation area,
Municipal Council area, Sugar producing area, Jail premises and naxalite affected area
an increase of percentage over than normal schedule of rates ( Basic completed item
rates) prescribed for the year 2015-2016 areas follows. ·
a) Notified Tribal areas or Hilly or inaccessible areas 10%
b) Corporation areas 5%
c) Municipal Council areas 4%
d' ... · ·~~~cane producing areas 5%
e) Jail premises, Mental Hospital, 15%
Rajbhawan
f) Naxalite affected area (For all works in 20%
Gadchiroli District.) As per Govt. of
Maharashtra, GAD letter No.WK-
2009/CR 102/Desk-1415 dated
31/12/2009.
( i ) The Superintending Engineers should specify the sugar factories area under their
circle after ascertaining working condition of the sugar factory.
( ii) The hilly/in accessible areas in Vidharbha region for Public Work Region, Nagpur are
identified as below.
Sr. No. District Hilly/In accessible areas
1 Nagpur
2 Wardha
3 Bhandara Government Resolution, Planning Department No.
4 Gondia DVK/1 089/P-66/Y-19 Dated 23-11-1990 & 13-06-2003
5 Chandrapur
6 Gadchiroli
... ..
( 111 ) If Ja1l prem1ses IS s1tuated 1n Corporation or Mumc1ple area, an mcrease of only
15% for jail primises is to considered.
(iv) Increase in rate under 2 (a) &(f) shall be applied only in the areas notified by the
State Government.
( v ) For Gadchiroli District Notified Trible area, Hilly or inaccessible area, an increase
shall be (1 0% + 20%) =30%
3) For rate of items which are not included in this schedule of rates shall be adopted from
schedule of rates for National Highway works Nagpur Region I Maharashtra Jeevan
Pradhikaran, Nagpur for the corresponding year.
(i)
4) Schedule of rates are based on the following rates of materials inclusive of ED and
VAT for Cement, Bitumen, Emulsion and Steel.
6) (a) The job mix design for items like M-25 & above grade of concrete mix design, GSB,
asphaltic concrete, bituminous macadam etc. shall be obtained from the V.Q.C.C.
laboratory
(ii)
(b) For RCC works of Building and bridges (Superstructure and substructure ), the
grade of concrete should be considered as per IS 456:2000 which stipulates minimum
grade as M 20.
7) TAXES AND GOVT. CIRCULARS.
7.1) The basic rates of materials are as per the Rates charged by the main producers I
suppliers at their respective points of supply, as on the date 01/07/2015 which include all
taxes such as excise, LWT, LBT, Terminal TAX, VAT, Educational Tax are considered.
The rates of bulk I packed bitumen, bitumen emulsion adopted for the items of
bituminous works are based on the rates prevailing on 01.07.2015 at ex-Refinery
Mumbai. Subsequent increase/ decrease if any, then these rates shall be accounted for
in the rate analysis of the items while framing the estimate.
7.2) As per G.R. of Industries and power Department No. BCA-2009/CR-108/Labour 7-A
Dated 17.06.2010, 1% cess for labour welfare is considered in the Rate Abstract.
7.3) As per revised circular issued by Dy. Directorate of Insurance Maharashtra State vide
letter No. ~- ~~~o;m.~.fcf./fCll1JcHjMl/31N-~. ~ 08.09 .2010, percentages for
insurance of contract work shall be added in the Recapitulation sheet while framing the
estimate. The actual amount incurred by contractor for insurance of work shall be
reimbursed on production of documentary evidence and after due verification.
a) Work value up to 25.00 lakh - 0.50%
b) Work Value above to 25.00 lakh - 1.00% (Relevant clause regarding reimbursement
shall be included in draft tender papers.)
7.4) As per Government of Maharashtra, Revenue and Forest Departments Notification No.
Gaunkhanin-1 0/1 012/PK-603/kh (3) dated 11th May 2015, Royalty charges of Rs.400/-
Brass, i.e. Rs. 141 .20 I Cum, are included in the respective items of supply of natural
minerals i.e .. Rubble, Metal, Sand, Murum etc.
7.5) The basic rates of bricks & crusher broken metal includes royalty charges.
8) General Guidelines
8.1) The rates for items pertaining to Parks & Gardens shall be taken from the DSR of, Parks
& Gardens.
8.2) For item:s of excavation, foundation concrete and masonry etc. for C. D. works, rates shall
be adopted from corresponding items under respective building sections.
8.3) For specific tests like span load test, plate/pile load test etc. which are not included in the
rate analysis of iteni, the payment/estimates for these tests will be prepared on the basis
of rates approved by M.E.R.I.
9) The charges towards quality control tests are considered in the scheduled rates
wherever necessary.
.a) For Building works, basic lead upto 5 Km. is considered for all completed items.
(iii)
b) The floor is designated by the space contained within the top of the virgin slab I roof
covering below to the top of the virgin slab I roof covering above.
c) for every additonal floor percentage increase in the rates shall be considered for the
items in the following section as given in table without deducting the cost of cement and
steel.
Sr. No Section Item Percentage
For Every For
Floor up to Every
4th Floor Floor
above
1 2 3 4 5
i BDF, BOG R.C.C, B.B.Masonry 3 1
ii BDF M. S./HYSD/TMT Reinforcement 1 0.25
iii BDJ Water Proofing Tr~atement 3 1
iv BDL Plastering,Poiinting 3 1
Flooring Dado skirting treads ( except
v BDM 3 1
Ceramictiles,Giazed tiles)
vi BDM Ceramic tiles, Glazed tiles, flooring dado 1 0.25
a) External Painting 3 1
vii BOO
b) Internal Painting 1 1
viii BDR Mangolare tile roof, Ridges Ceiling 3 1
Weather Shade Replacing External Window
ix BOT 1 0,25
shutter using scaffolding
X BDU/BDC Structural Steel Work, Tubular trusses 1 0.25
Soil,waste,vent and rain water pipes and
xi BDV 1 0.25
sanitary wares etc.
xii - Item not covered under Sr. No. ito xi above . 1 0.25
The Increase m rates as above should be on ground floor bas1c rates only. No cumulative
increase shall be done. 'J
Item to be carried out above terrace such as water proofing treatment on terrace, water
storage tank, parapet wall with coping, staircase, lift room with slabs and water proofing
treatment, plaster, painting etc. required for the completion of building are assumed to be
the items of its lower floor.
\.
d) In Nagpur Corporation area and Chandrapur Municipal area the use of clay bricks is
-prohibited on original works. For such works only fly-ash bricks shall be used , except for
foundation of load bearing structures. The Clay Bricks can be used for Maintenance Work
only.
e) The use of wooden centering & formwork including wooden props is prohibited. Only
plywood or steel formwork is to be used with steel props.
,..
(iv)
f) With a view to conserve the natural resources, the use of country teak wood for doors
and windows shall be avoided as far as possible, except for doors located on the external
g) For the items of oil painting, distempering under Bd - 0 & Bd- P, the sample shall be.
got approved by Executive Engineer & a note regarding make I Company of approved
i) The pattern of fixing flooring tiles I stones shall be got approved from Dy. Chief
Architect/ Superintending Engineer.
Chromium Plated 2%
Aluminium Oxidised I Stainles.s
5%
steel
Stainless steel with matt finish 6%
Brass 20%
Brass Oxidised 23%
FOR WINDOWS
Chromium Plated 1%
_ __:__
Brass 15%
Brass Oxidised 17%
a) Rates for collection of material for road work, are at quarry site with lead upto 50
mtrs. Lead charges shall be considered separately while preparing the estimate for
road work. For concrete pavement items basic lead of 5 km is considered.
12) For bridge work and C.D. work basic lead of 5 Km. is considered.
a) For working out rates for items with leads more than 5 km. the estimate should be
prepared for actual leads deducting initial lead charges of 5 km. for all completed items
except items of road work.
b) For providing plain cement concrete for ·piers, abutments; returns, wings etc. if surface
reinforcement is provided in these structures , the rate for concrete should be same as .
that of plain cement concrete, cost of reinforcement should be separately considered.
(v)
13) Additional lift for bridge items :-
For additional lift for various bridge items as per list given below, rate shall be increased
in percentage given below. Lift is to be measured with respect to common datum level
for raft foundation the datum level shall be raft top. For other type of foundation, average
bed level shall be treated as datum.
a) Pier ,Abutment, Returns, Wing Nil
wall, Pier cap,Box Returns.Upto
4.00m
b) For every additional 2.00 m 3.50%
beyond 4.00 m from datum
a) The items of hot mix hot laid bituminous works are excluding transportation of bulk
bitumen from refinery to plant site. Cost of bitumen considered in these items is as rates
described in note (4) under column 3.
b) For hot mix hot laid B.T. items rates do not include any initial lead for crushed metal
as well as for hot mix material. Lead for transportation of crushed metal from quarry to
plant site and lead of transportation of hot mix material from plant to work site shall be
added seprately.
c) For transportation of Hot Mix Material from plant to work site , the loose quantity of Hot
Mix Material shall be considered while preparing the estimate.
d) Quantity of bitumen has been taken from MORT&H- specification of Roads & Bridges
2013 I Standard data book and PWD Standard Specifications. The actual quantity will
depends upon the job mix formula wherever applicable.
(vi)
BUILDING
I
WORKS
BD-A EXCAVATION
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I
Labour
1
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
9 Providing and filling in the foundation and plinth Cu.m 490.00 71 .00
BOA with sand of approved quality including watering,
13 compaction complete.
( Including Royalty)
Spec. No. : Bd.A. 131Page No. 264
10 Providing soling using 80 mm size granite I Cu.m 600.00 1'99.00
BOA quartzite I gneiss I trap metal in 15 em. layer
14 including hand packing filling voids with sand I grit,
ramming, watering etc complete.
( Including Royalty)
Spec. No. : As directed by Engineer-in-charge.
3
BD - B : PILE FOUNDATION
SR.N DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
0. (In Rs.)
&
CODE Completed Labour
NO.
1 Providing single under reamed piles of
specified diameter with following grade of
concrete including boring, under reaming in
all sorts of soils, filling the bulb and stem
with C.C.mix (excluding steel
reinforcement) as per detailed specification
and drawings etc. complete.
i) 20 em diameter
M-20 grade Rmt. 488.00 235.00
M-25 grade Rmt. 503.00 240.00
ii) 25 em diameter
M-20 grade Rmt. 659.00 294.00
M-25 grade Rmt. 673.00 296.00
iii) 30 em diameter
M-20 grade Rmt. 806.00 299.00
M-25 grade Rmt. 826.00 301.00
iv) 37.50 em diameter
M-20 grade Rmt. 1096.00 305.00
M-25 grade Rmt. 1126.00 306.00
Spec. No. : I.S. 2911 - Part I 1964 Clause
No. 6.1.5.
4
BD- C STRUCTURAL STEEL WORK
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
5
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
6
· BD- E PLAIN CEMENT CONCRETE
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
7
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
4 Providing and laying in situ, cement concrete M-15 Cu.m. 4356.00 868.00
BDE of trap/ granite/quartzite/gneiss metal for foundation
1 and bedding including bailing out water,
plywood/steel formwork, compacting, finishing
uneven · and honeycombed surface, curing etc.
complete. The Cement Mortar 1:3 plaster is
considered for rendering uneven and honeycombed
surface only. Newly laid concrete shall be covered
by gunny bag, plastic, tarpaulin etc. (Wooden
centering will not be allowed.)
6 Providing and casting in situ cement concrete M-15 Cu.m. 4486.00 869.00
BDE of trap/ granite/quartzite/gneiss metal for coping to
3 plinth or parapet, moulded or chamfered as per
drawing or as directed including steel centering,
plywood/steel formwork compacting, roughening
them if special finish is to be provided, finishing
uneven and honeycombed surface and curing etc.
complete. The Cement Mortar 1:3 plaster is
considered for rendering uneven and honeycombed
surface only. Newly laid concrete shall be covered
by gunny bag, plastic, tarpaulin etc. (Wooden
centering will not be allowed.)
8
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed J Labour
9
BD- F REINFORCED CEMENT CONCRETE
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
10
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
11
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (I n Rs.)
CODE
Completed Labour
NO.
5
. .
Prov1d1ng and casting in s1tu cement concrete
BDF of required grade of trap I granite /quartzite
6A /gneiss metal for R.C.C. beams and lintels as
per detailed design and drawings or as
directed,including steel centering, plywood/steel
formwork steel props, compaction , finishing
uneven and honeycombed surface with C.M.1 :3
of sufficient minimum thickness to give a smooth
and even surface or roughening if special finish is
to be provided and curing etc. complete.
Including use of plastisizer wherever necessary
as directed by Engineer-In-charge (Excluding
reinforcement, including cover block). The
Cement Mortar 1:3 plaster is considered for
rendering uneven and honeycombed surface
only. Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc. (Wooden
centering will not be allowed)
a) For C.C.M-20 Cu.m. 6992.00 1846.00
b) For C.C.M-25 Cu.m. 7157.00 1859.00
12
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
. .
7 Provrdrng and castrng rn srtu cement concrete of
BDF required grade of trap I quartzite /granite /gneiss
10A metal for R.CoC. canopy as per detailed design
and drawings including steel centering, plywood I
steel formwork, steel props,compaction, finishing
uneven and honeycombed surface with C.M. 1:3
of sufficient minimum thickness to give a smooth
and even surface or roughening surface if special
finish is to be provided and curing etc. complete.
(Excluding reinforcement, including cover
block) The Cement Mortar 1:3 plaster is
considered for rendering uneven and
honeycombed surface only. Newly laid concrete
shall be covered by gunny bag, plastic,
tarpaulin etc. (Wooden centering will not be
allowed)
a) For C.C.M-20 Cu.m. 7629.00 2102.00
b) For C.C.M-25 Cu.m. 7777.00 2110.00
Spec. No.: Bd.F.1 0/ Page No.304/I.S. 456 (2000)
13
SR. NO. DESCRIPTION OF ITEMS . UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
..
9 Prov1dmg and castmg 1n s1tu cement concrete of
BDF required grade of trap I granite /quartzite /gneiss
7A metal for R.C.C.Portals as per detailed design
and drawings or as directed including steel
centering, plywood I steel formwork, steel props,
compaction, finishing uneven and honeycombed
surface with C.M.1 :3 of sufficient minimum
thickness to give a smooth and even surface or
roughening the surface if special finish is to be
provided and curing etc. complete. (Excluding
reinforcement, including cover block). The
Cement Mortar 1:3 plaster is considered for
rendering uneven and honeycombed surface
only. Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc. (Wooden
centering will not be allowed)
14
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
. .
Prov1d1ng and casting in situ cement concrete of
11 required grade of trap I granite /quartzite /gneiss
BDF metal for R.C.C slabs and landings as per
8A detailed design and drawings including steel
centering, plywood /steel formwork, steel props,
compaction, finish ing uneven and honeycombed
surface with C.M. 1:3 of sufficient minimum
thickness to give a smooth and even surface or
roughening the surface if special finish is to be
provided and curing etc. complete. (Excluding
reinforcement, including cover block) The
Cement Mortar 1:3 plaster is considered for
rendering uneven and honey combed surface
only. Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc. (Wooden
centering will not be allowed)
15
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
..
13 Prov1d1ng and castmg m s1tu cement concrete of
BDF required grade of trap I quartzite /granite /gneiss
13A metal for R.C.C. Waist slab, and steps of
staircases as per detailed design and drawings
or as directed including steel centering, plywood/
steel formwork, steel props, compaction, finishing
uneven and honeycombed surface with C.M. 1:3
of sufficient minimum thickness to give a smooth
and even surface or roughening the surface if
special finish is to be provided and curing etc.
complete. (Excluding einforcement, including
cover block) The Cement Mortar 1:3 plaster is
considered for rendering uneven and
honeycombed surface only. (Newly laid
concrete shall be covered by gunny bag,
plastic, tarpaulin etc.) (Wooden centering will
not be allowed)
16
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
15 Providing and casting in situ cement concrete of
BDF required grade of trap I quartzite /granite /gneiss
14A metal for R.C.C.newel posts of staircase as per
detailed design and drawings including steel
centering, plywood I steel formwork, steel props,
compaction, finishing uneven and honeycombed
surface with C.M.1 :3 of sufficient minimum
thickness to give a smooth and even surface or
roughening the surface if special finish is to be
provided and curing etc. complete. (Excluding
reinforcement, including cover block) The
Cement Mortar 1:3 plaster is considered for
rendering uneven and honeycombed surface
only. (Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc.) (Wooden
centering will not be allowed)
17
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
18 Providing and casting in situ cement concrete of
BDF required grade of trap I granite I gneiss I
11A quartzite metal for R.C.C. pardi 75 mm thick
including steel centering, plywood /steel
formwork, compaction, finishing uneven and
honeycombed surface with C.M . 1:3 of sufficient
minimum thickness to give a smooth and even
surface or roughening them if special finish is to
be provided and curing etc.complete.(Excluding
reinforcement, including cover block) The
Cement Mortar 1:3 plaster is considered for
rendering uneven and honeycombed surface
only.( Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc.) (Wooden
centering will not be allowed)
18
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed labour
NO.
21 Providing and fixing in position after hoistJng, Sq.m. 485.00 105.00
precast 1 :2 cement mortar reinforced jali 50
mm thick of approved design on both sides
fixing in cement mortar 1:3 and curing complete.
(with 3 mm diameter mild steel bar
reinforcement)
Spec.No.: Bd.F.20 I Page No.307
23 Providing and fixing at site precast steel fibre Rmt 1703.00 482.00
BDF reinforced concrete M 30 grade precast
boundary wall of height of 1.50 m including
column of size 0.15m x 0.15m and panels of size
2.10 x 0.30 x 0.05 m , excavation for column
foundation and C.C. M 15 for foundation
including transportation of precast column and
panel from factory to work site etc. complete.
19
BD • G : BRICK MASONARY
.•
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO,
Completed I Labour
1 Providing Fly ash lime brick masonry (bricks Cu.m. 3868.00 1011.00
BOG conforming to I.S.12894 : 1990 of size 19 em
1 x 9 em x 9 em ) in cement mortar 1 :6 in
foundations and plinth of inner walls I
external walls including bailing out water,
striking joints on unexposed faces, racking out
joints on exposed faces and watering
complete.
Spec.No.: Bd.G.1/Page No.313
20
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed I Labour
NO.
21
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
22
80-H: STONEMASONARY
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
23
BD - I : BLOCK MASONARY
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
1 Providing and laying I.S. standard C.C. Sq.m. 451.00 173.00
BDI hollow block 100 mm x 200 mm x 400 mm
1 (100 mm thick) in C.M. 1:6 for
Superstructure including racking out joints,
when plastering is to be done/striking joints
when no plastering is to be done, curing and
scaffolding etc. complete.
Spec.No.: Bd.I.1/Page No.349
24
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. .
Completed I Labour
25
BD- J : WATER PROOFING
SR. NO. DESCRIPTION OF ITEMS UNIT RATES != OR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
1 Providing and laying damp proof course 50 mm Sq.m. 314.00 77.00
BDJ thick in (1 :2:4)/ M-15 cement concrete layer and
2 bitumen felt using cement with water proofing
compound etc. complete.
26
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
. .
3 Provrdrng water proofing in W.C. and bath Cu.m. 3801.00 1437.00
BDJ including 8.8. Coba in all position consisting of
9 specialised approved waterproofing compound
and materials as per manufacturers specifications
and covering 7 years guarantee on court fee
stamp paper of Rs.100/- including all lead, lift and
ponding test etc. complete.
27
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (I n Rs.)
NO.
. .
Completed I Labour
6 Prov1d1ng and lay1ng Hyperplas Alummum or Sq.m. 688.00 203.00
equivalent polymeric multiple monolithic five
layer water proofing flexible, pliable and high
tensile strength membrane (3 kg/sqm) which is
comprise of top with "V" shape embossed 40
micron Aluminum foil to bear thermal expansion
and avoiding delamination & consist of centre core
of 90 micron thick High Molecular High density
Polyethylene film (HMHDPE) which is protected on
both the side with polymeric mix. Applying the
membrane by thermofusing to roof & parap~t after
applying thin film of hot blown bitumen 85/25 or
90/15 grade @ 1.2 kg/sqm maximum as per
surface condition or Hyperplas primer @ 250
gms/sqm as per site condition on the surface to be
treated with 10 em overlapping including finishing
etc. complete and covering guarantee of 7 years
on stamp paper of Rs. 100/- and as directed by
Engineer-in-charge. (Prior permission of S.E.in
writing is necessary before inclusion of this item in
estimate).
28
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed J Labour
..
8 Prov1d1ng Water proofing treatment to newly Sq.m. 1132.00 208.00
laid fully cured concrete slab of terraces by
applying first coat of polymer modified semi-
viscous paste prepared by mixing polymer of
approved make (such as Master Seal 5501 brush
bond I RoffSupercrete I Webercrete I Monobond
IPerma shield I Hypercrate I Master Crete M 81 I
MC-Bauchemie) and Cement in 1 : 2 proportion ( 1
litre polymer : 2 Kg. Cement) or Rohnex water
proofing system in two coats( 1kg powder, 700 ml
water and polymer jelly for first coat & 1 kg
powder,500 ml water & polymer jelly for second
coat )to a neatly cleaned and dust free concrete
surface and upto 300 mm. over parapet wall
prepared by removing loose and deposited
material with brush and water, ,laying glass fibre
mesh of 10 x 10 specification of approved make
over tacky surface of first coat of polymer followed
by second coat in transverse direction, sprinkling
coarse sand over it, followed by protective
mechanical cover of 40 mm to 75 mm. thick
cement concrete of 1:2:3 proportion using coarse
aggregate of 10 MSA and water proofing
compound of approved make and polypropylene
fibres @ 125 gm per bag of cement within it
confirming to IS, in pannels of 3ml4m oras per site
condition & filling the joints with polt sulphide
sealant(0.08 kg per sq.mt.) after curing including
providing holler with drip moulds at the junction
and finishing the concrete surface with neat
cement slurry,incuding curing as directed and
ponding the surface as directed etc.complete ;
covering 7 years guarantee against leakproofness
on court Fee stamp paper of Rs 1001-
29
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
..
9 Providing Water proofing treatment to old Sq.m. 1213.00 244.00
terraces by removing existing treatment,
sealing of cracks by non shrink crack fill
compound applying first coat of polymer modified
semi-viscous paste prepared by mixing polymer of
approved make (such as Aquatek conchem/
Master Seal 550/ brush bond/ RoffSupercrete I
Webercrete I Monobond I Perma shield I
Hypercrate I Master Crete M 81/ MC-Bauchemie)
and Cement in 1 : 2 proportion (1 litre polymer : 2
Kg Cement )or Rohnex water proofing system in
two coats(1kg powder,700 ml water and polymer
jelly for first coat & 1 kg powder,500 ml water &
polymer jelly for second coat) to a neatly cleaned
and dust free concrete surface and upto 300 mm
over parapet wall prepared by removing loose and
deposited material with brush and water, followed
by two coat of flexible cementious coating eg.
MYK-Aqufine U.M., Monopal G. coat or equivalent
as per manufacture specification after laying glass
fibre mesh of 10 x 10 specification of approved .
make over tacky surface of first coat of polymer
followed by second coat in transverse direction,
sprinkling coarse sand over it, followed by
protective mechanical cover of 40 mm to 75 mm.
thick cement concrete of 1:2:3 proportion using
coarse aggregate of 10 MSA and water proofing
compound of approved make along with 14 guage
40 mm x 40 mm size welded mesh and
polypropylene fibres @ 125 gm per bag of cement
within it conforming to IS in pannels o-r 3m/4m oras
per site condition & filling the joints with polt
sulphide sealant(0.08 kg per sq.mt.) after curing,
including providing holler with drip moulds at the
junction and finishing theconcrete surface with
neat cement slurry including curing as directed
and ponding the surface as directed etc.
complete; covering 7 years guarantee against
leakproofness on Court Fee Stamp Paper of Rs.
100/-
30
-
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
10 Providing water proofing treatment to newly Sq.m. 1062.00 190.00
laid fully cured concrete slab of terraces by
applying first coat of polymer modified semi -
viscous paste prepared by mixing polymer of
approved make (such as Aquatek conchem/
Master Seal 550 I brush bond/ RoffSupercrete
/Webercrete /Monobond I Perma shield I
Hypercrate I Master Crete M 811 MC-Bauchemie)
and Cement in 1:2 proportion (1 litre polymer : 2
Kg Cement)or Rohnex water proofing system in
two coats(1kg powder,700 ml water and polymer
jelly for first coat & 1 kg powder,500 ml water &
polymer jelly for second coat) to a neatly cleaned
anq dust free concrete surface and upto 300 mm
over parapet wall prepared by removing loose and
deposited material with brush and water, laying
glass fibre mesh of 10 x 10 specification of
approved make over tacky surface of first coat of
polymer followed by second coat in transverse
direction, laying mechanical protective cover to
polymer coating treatment with brick bat coba with
burnt broken brick bats laid in C.M. 1:5 admixed
with approved water proofing compound filling up
to half depth of brick bats, curing this layer for 3
days, applying cement slurry over this layer, joints
of Brick Bats with C.M. 1:3 admixed with approved
water proofing compound and finally top
finishing with average 20mm thick layer of same
mortar added with polypropylene fibers at 125 gm
per bag of cement including finishing the surface
smooth with neat cement slurry admixed with
approved water proofing compand, Marking
finished surface by false squares of 300 mm x
300 mm, Making the junctions at the parapet
rounded and tapered top for required height, with
drip mould at the junction of plaster and prapet
and curing and covering 7 years Guarantee
against leak proofness on court fee stamp paper
Rs. 100/- including pending test etc. complete
31
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
11
..
Prov1d1ng water
.
proofmg treatment of Old Sq.m. 1102.00 219.00
Terraces by removing existing treatment. Sealing
of cracks by non shrink cracks fill compound by
applying first coat of polymer modified semi-
viscous paste prepared by mixing polymer of
approved make (such as Aquatek concheml
Master Seal 5501 brush bond I RoffSupercretel
Webercretel Monobond I Perma shield I
Hypercrate I Master Crete M 811 MC-Bauchemie)
and Cement in 1:2 proportion ( 1 litre polymer : 2
Kg Cement)or Rohnex water proofing system in
two coats(1 kg powder, 700 ml water and polymer
jelly for first coat & 1 kg powder,SOO ml water &
polymer jelly for second coat) to a neatly cleaned
and dust free concrete surface and upto 300 mm
over parapet wall prepared by removing loose and
deposited material with brush and water, laying
glass fibre mesh of 10 x 10 specification of
approved make over tacky surface of first coat of
polymer followed by second coat in transverse
direction, laying mechanical protective cover to
polymer coating treatment with brick bat coba with
burnt broken brick bats laid in C.M. 1:5 admixed
with approved water proofing compound, filling up
to half depth of brick bats, curing this layer for 3
days, applying cement slurry over this layer joints
of brick bats with C.M. 1:3 admixed making the
junctions at the parapet rounded and tapered top
for required height, with drip mould at the junction
of plaster and parapet and curing and covering 7
years Guarantee against leakproofness on court
fee stamp paper of Rs. 1001- including ponding
test etc. complete
(Excluding grouting and Removing existing
treatment to be paid separately as required)
32
•
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
..
12 Provrdrng water proofing treatment to Bath & Sq.m. 1213.00 345.00
W.C. sunk by applying first coat of polymer
modified semi-viscous paste prepared by applying
grouting with cement slurry admixed with non
shrink grout additives as per manufacturers
specifications, mixing polymer of approved make
(such as Aquatek conchem/ Master Seal 5501
brushbondl RoffSupercrete/ Webercretel
Monobond I Perma shield I Hypercrate I Master
Crete M 811 MC-Bauchemie) and cement in 1:2
proportion (1 litre polymer : 2 Kg Cement)or
Rohnex water proofing system in two coats(1 kg
powder, 700 ml water and polymer jelly for first
coat & 1 kg powder,500 ml water & polymer jelly
for second coat to a netly cleaned and dust free
concrete surface prepared by removing looseand
deposited material with brush and water, laying
glass fibre mesh of 10 · x 10 specification of
approved make over tacky surface of first coat of
polymer followed by second coat in transverse
direction, sprinkling coarse sand over it followed
by protective mechanical cover of 15 to 20 mm
thick polymer modified plaster to coated surface of
sunk '@ 2 litre per bag of cement and filling joints
with non shrink compound and covering 7 years
guarantee against leakproofness on court fee
stamp paper of Rs. 1001-
33
BD- J-1 :REPAIRS & REHABILITATION
SR. NO. UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
34
BD- K EXPANSION JOINTS
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
35
BD- L PLASTERING AND P.OINTING
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015 ..16
& (In Rs.)
CODE
NO.
Completed I Labour
36
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
7 Providing rough cast cement plaster for Sq.m. 381 .00 241.00
external portion in two coats to concrete,
brick or stone masonry surfaces in all
positions with base coat of 12 to 15 mm thick
in C.M . 1:4 and rough cast treatment 12 mm
thick in proportion 1:3 including scaffolding ,
making grooves and fourteen days curing
complete.
Spec.No. Bd.L.81page No. 370
37
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
38
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& . (In Rs.)
CODE
NO.
Completed I Labour
39
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
40
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& - (In Rs.)
CODE
NO.
I
Completed . Labour
19 Providing and fixing glass fiber mesh Alkali Rmt. 72.00 44.00
resistance, 50 gsm, 10 x 10 about 30 em.
width at the junction of R.C.C members and
~rick work, of approved quality including
., .
applying bond coat of acrylic polymer &
cement by brush in 1:1 proportation, fixing
mesh over it, tying by nails & binding wire etc.
complete.
Spec. No. :As directed by Engineer- in-charge.
41
BD- M PAVING, FLOORING AND DADO
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
42
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
43
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
44
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed l Labour
45
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
46
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed ·I Labour
19 Providing and fixing in position Partition of
polished Kaddappa I Marble I Granite stone
of required thickness ,including making
groove in wall I concrete surface filling joints
with slurry, curing, polishing, rounding edges,
as required cleaning etc. complete .
22 Providing and laying plain cement tiles for Sq.m. 488.00 232.00
BDM treads and risers of steps and .staircases
23 with nosing of treads moulded as per
drawings or as directed on a bed of C.M. 1:4
including cement float filling joints with neat
cement slurry, curing, polishing and cleaning
complete.
Spec.No.: Bd.M.23/Page No.390
47
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
48
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
49
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
50
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed J Labour
51
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
52
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
40 Finishing upto 225mm thick cement concrete Sq.m . 73.00 0.00
laid . to proper level and slope including
compacting finishing with tremix treatment
for paving slab with compaction by screed
vibrator , removing excess water from the
cement concrete by tremix vaccum
dewatering system , finishing the surface with
floater and traveler including all etc. complete
as directed
Spec.No.: As directed by Engineer- in-charge.
53
BD - N : WOOD FINISH
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
6 Providing and applying coal tar in one coat Sq.M. 16.00 7.00
BON on previously painted wood including
16A preparing the surface, scaffolding etc.
complete.
Spec.No.: Bd.N.1.6/Page No.400
54
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
7 Providing and applying coal tar in two coats Sq.M. 25.00 11.00
BDN on new wood work including preparing the
168 surface, scaffolding etc. complete.
55
BD - 0 : OIL PAINTING
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
56
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
. Completed I Labour
-
6 Providing and applying three coats of Sq.m. 93.00 31.00
BOO synthetic enamel paint of approved colour to
SA new and old structural steel work and
wood work in buildings, including
scaffolding if necessary, cleaning and
preparing the surface (including primer coat)
complete. (Sample and brand is to be got
approved from Ex. Engineer before use)
57
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
9 Providing and applying two coats of flat oil Sq.m. 62.00 26.00
BOO paint of approved colour and shade to
7A internal/External plastered old surfaces
including _:scaffolding if necessary, cleaning
and preparing the surface including primer
coat complete. (Sample , and brand is to be
got approved from Ex. Engineer before
- use)
Spec.No.: Bd.0.7/Page No.406
10 Providing and applying three coats of flat oil Sq.m. 93.00 32.00
BOO paint of approved colour and shade to
7B internal/ External plastered old/new
surfaces including scaffolding if necessary,
cleaning and preparing the surface including
primer coat complete. (Sample and brand is
to be got approved from Ex.Engineer
before use)
Spec.No.: Bd.0.7/Page No.406
58
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
..
Completed I Labour
18 Removing old paint from steel · and other Sq.m. 22.00 19.00
BOO metal surface with flame, cleaning and
8B making the surface even and scaffolding etc.
complete.
Spec.No.: As directed by Engineer- in-charge.
"
19 Removing old paint from steel and other Sq.m. 8.00 7.00
BOO metal surface with hand scrapping,
82 cleaning and making the surface even and
scaffolding etc. complete.
Spec.No.: As directed by Engineer- in-charge.
60
BD- P COLOUR/WHITE WASHING, DISTEMPERING
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I
Labour
1 Providing and applying primer coat for wall Sq.m. 14.00 7.00
BOP surface to receive oil bound distemper
70 treatment.
Spec.No. : As directed by Engineer- in-charge.
61
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
8) Two coats
i ) For old surface Sq.m. 35.00 16.00
ii ) For new surface Sq.m. 43.00 18.00
Spec.No.: Bd.P.S/Page No.413
62
BD - Q : WOOD WORK
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
1 Providing and fixing in position P.V.C. hand rail of Rmt. 353.00 59.00
BDQ approved quality, make and shade including M.S.
24A plate of required size as directed etc. complete.
(50 mm size)
Spec.No.: As directed by Engineer- in-charge.
2 Providing and fixing double leaf steel shutter Sq.m. 1505.00 588.00
with frame to wall cupboard of 18 gauge
M.S.sheet as per standard drawing including
oxidised fixtures and fastenings with locking
arrangment including G.I.Sheet shelves at 40
em center to center including primer coat and
three coats of enamel paint of approved colour
and pattern finishing fixing in position complete.
Spec.No.: As directed by Engineer- in-charge:
3 Providing and fixing double leaf steel shutter Sq.m. 1064.00 402.00
with frame to wall cupboard of 18 gauge
M.S.sheet as per standard drawing ·including
oxidised fixtures and fastenings with locking
arrangement excluding shelves, including primer
coat and three coats of enamel paint of approved
colour and pattern, finishing fixing in position
complete.
Spec.No.: As directed by Engineer- in-charge.
64
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I
Labour
•.
63
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed l Labour
4 Providing and fixing 12.5 mm. thick GYPSUM Sq.m. 763.00 336.00
board (conforming be I.S.2093-1982) panelling
on plastered/unplastered brick block/concrete
walls, Gypboard screw fixed with dry wall screw
25 mm. at 300 mm. Centres to perimeter channels
of size 27 mm ., 0.5 mm. th ick having one flange of
20 mm. and another flange of 30 mm. alongwith
ceiling sections of 0.55 mm. Thickness having
knurled wedge of 51 .5 mm. and 2 flanges of 26
mm. at 610 mm.c/c. pads with Dab fixer placed at
appropriate distances at top and bottom under the
ceiling section including good quality of approved
sundry materials and finishing smooth including
filling and finishing with jointing compound and
paper tape and two coats of primer etc. complete
upto the satisfaction of Engineer- in-charge. (Prior
approval shall be obtained from S.E. before
inclusion of this item in estimate)
6 Providing and fixing jungle wood common rafters, Cu.m. 51024.00 10092.00
BDQ purlins, and purlins cleats, hip rafters, jack rafters,
SA ridges, wall plates, post plates and posts for
roofing for weather shed etc. including scaffolding
if necessary, all iron work painted with one coat of
primer complete.
Spec.No.: Bd.Q.5/Page No.423
65
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
8 Providing and fixing 100 mm dia. Country teak Rmt. 180.00 21 .00
BDQ wood ballies for post truss of 6.00 m. span as
23 per drawing or as directed by Engineer- in-charge
including all iron work, scaffolding if necessary
and oiling complete.
Spec.No.:Bd.Q.22/Page No.434
9 Providing and constructing superior indian teak Rmt. 866.00 249.00
BDQ wood hand rail of 60 mm x 70 mm as per
8 detailed drawings or as directed by the Engineer,
including french polishing complete.
Spec.No.: Bd.Q.8/Page No.425
66
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
67
BD- R : ROOFING AND CEILING
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
68
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
69
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
9 Providing and fixing false ceiling of 12mm thick Sq.m. 1544.00 198.00
BDR acoustic boards of approved make, with shapes
19 and sizes as per drawings including scaffolding,
frame work of country teak wood battens of size 70
x 45 mm and 35 x 35 mm at 60 em centre to centre,
all screws and fastenings and finishing complete.
( runner to be paid separately).
70
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
13 Supplying and fixing and laying in Grid Unilock Sq.m. 1245.00 244.00
BDR false Ceiling System, size of the Grid 610 mm x
45 610 mm of which main runner shall be aluminium
silver anodised 25 micron bulb "T" (U-202) of size
35 x 23.5 x 1.5 mm suspended at 1200 mm centre
to centre with 6 mm M.S.Hanger rod with ends
connected with G.l. clamps and adjustable G.I.J.
hooks, cross "T" shall be aluminium silver anodised
5 micron (U-404) of size 23.5 x 23.5 x 1.5 mm fixed
to wall with dash through screws. The finished grid
shall contain 9.5 mm Gypsum board with coated
ceiling tiles with two coats of roller finish top
coat complete. (Prior permission of S.E to be
obtained before inclusion of item in estimate)
72
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-1 6
&CODE (In Rs.)
NO. Completed Labour
17 Providing & f1xing of approved make PVC false Sq .m. 2020.00 378.00
·soR ceiling on M.S. Rectangular hollow section
21 38mm x 25mm fixed to wall with PVC roll plugs and
duly main runner & intermediate section of
M.S.square tube 25mm x 25mm duly coated with
anti corrosive primer & ceiling panel made out of
rigid PVC multichamber hollow section of size 6mm
x 250mm. Joined with concealed screws fixed on
structure and no frame elements is visible from
outside including suspenders and necessary
holes/cuts for light fixtures and remaking damaged
su11ace etc. (Prior permission of S.E. to be
obtained before inclusion of this item in this
Specification- as directed by Engineer-incharge
18 Providing and fixing Mangalore tiled roofing with Sq.m. 468.00 76.00
BDR class "AA'' tiles including securing the last course of
1 tiles near the eaves with steel flat 40 mm x 3 mm
and 1.22 mm wire, fixing 50mm x 25mm horizontal
teak wood battens and iron works and oiling the
battens complete. (excluding ridge and hip tiles)
19 Providing and fixing Mangalore tiled roofing with Sq.m . 482.00 78.00
BDR class "AA" tiles including securing the last course of
2 tiles near the eaves with steel flat 40 mm x 3 mm
and 1.22 mm wire, fixing country teak wood sloping
battens of 25 mm x 12 mm, teak wood horizontal
battens of 50 mm x 25 mm over the sloping
battens, all iron works and coal tarring the battens
complete. (excluding ridge and hip tiles)
21 Providing and fixing glass tiles of Mangalore type No. 490.00 49.00
BDR at required places in Mangalore tile roof including
11 scaffolding necessary.
Spec.No.: Bd.R.11/Page No. 456
73
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-1 6
&CODE (In Rs.)
NO. Completed Labour
22 Providing and fixing new Mangalore tiles with "AA" Sq.m. 170.00 21 .00
BDR class tiles including scaffolding complete.
31
Spec.No.: As directed by Engineer- in-charge.
23 Providing and fixing Mangalore pattern cowl No. 93.00 11.00
BDR ventilator tiles in the required places in a
13 Mangalore tiled roof including scaffolding
necessary.
Spec.No.: Bd.R.13/Page No. 459
24 Providing and fixing country teak wood battens 50 Rmt. 90.00 10.00
BDR m,m x 25 mm for Mangalore tile roofing with all
29 iron work, scaffolding and oiling the battens
complete.
Spec.No.: As directed by Engineer- in-charge.
74
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
28 612.00 248.00
0 0 0 0
75
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
29 Providing and fixing colour coated Galvalume (A- Sqm 1089.00 158.00
Z) sheet having high tensile(min 550 MPa in Yield
strength) C.R. steel base metal with hot dip 'alloy
coating of Alluminium and Zinc with 0.50 mm
overall sheet thickness for roofing with approved
profile and colour including fixing to purlins with
approved self tapping screws and EPDM
washers etc complete( Prior approval of Sample
and brand by Ex. Engineer is necessary before use)
\' t
30 Providing and fixing colour coated Plain Galvalume Rmt. 612.00 92.00
(A-Z) sheet 60 em wide having high tensile (min
550 MPa in Yield strength) C.R. steel base metal
with hot dip alloy coating of Alluminium and Zinc
.with 0.50 mm overall sheet thickness for ridge,hip
or valley or eaves board including fixing with
approved self tapping screws and EPDM washers
,scaffolding etc complete( Prior approval of Sample
and brand by Ex. Engineer is necessary before use)
76
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE -· (In Rs.)
NO. Completed Labour
78
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed Labour
(':j
BD - T : DOORS AND WINDOWS
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
3 Providing and fixing country teak wood frame of Cu.m 116788.00 19450.00
BOT required section for second class doors with/without
2 ventilator windows and wondows fan light and clear
storey windows including all mouldings, chamfering,
rounding, and abauting holdfasts and finishing with
one coat of primer and two coats of oil painting etc.
complete.(Only for exterior doors)
80
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
4 Providing and fixing country teak wood single leaf, Sq.m 3564.00 1180.00
BDT 2nd class partly panelled and partly glazed door
12 without fan light I ventilator as per drawings including
iron oxidised fixtures and fastenings and finishing the
wood work with one coat of primer etc.(excluding
door frame) complete.
Spec.No. : Bd.T.12/Page No.483
5 Providing and fixing country teak wood 20mm thick
BDT false panelled door shutter without fanlight as per
23 detailed drawings including iron oxidised fixtures and
finishing with one coat of primer etc.(excluding door
frame) complete.
a) Double leaf Sq.m 3840.00 1220.00
81
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
82
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
11 Providing and fixing rolling steel shutters fabricated Sq.m. 2;136.00 332 .00
BDT from 20 guage steel laths with slide guides, bottom
55 rail, brackets, door suspension shaft including
rolling springs, locking arrangement and housing
box at_top including one coat of red lead primer etc.
complete.
Spec.No.: Bd.T.55/Page No.510.
12 Providing and fixing rolling steel shutters fabricated Sq.m. 3057.00 527.00
BDT from 20 guage steel laths with slide guides, bottom
56 rail, brackets, door suspension shaft, housing box at
the top including mechanical gear operation
arrangement and one coat of red lead primer etc.
complete.
Spec.No.: Bd.T.56/Page No.511.
83
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed ~ Labour
13 Providing and Fixing collapsible steel gates in two Sq.m. 2983.00 1067.00
BOT leaves with channel pickets, pivoted flat bars,
57 including top and bottom guides, rollers, stoppers,
handles, all fitting accessories, locking arrangement
and one coat of red lead primer etc. complete.
Spec.No. : Bd. T. 57/Page No. 511.
14 Providing and fixing 24 guage PLAIN ALLUMINIUM Sq.m. 627.00 332 .00
BOT SHEET on the face of door shutter including cutting
95 to required size and fixing by screws including making
good the damages if any to existing door shutter and
frame etc. complete as directed or as per detailed
drawing.
Spec. No.: As directed by Engineer- in-charge
15 Providing and fixing crimped wire netting single Sq.m. 3203.00 1054.00
BOT shutter with 60 mm x 100 mm country teak wood
118 door frame including oil painting 3 coats and iron
oxidised fixtures and fastening complete.
Spec.No.: As directed by Engineer- in-charge.
16 Providing and fixing M.S. grill doors weighing 22 to Sq.m. 1696.00 399.00
BOT 24 kg per sq. meter of required size as per detailed
122 drawing without hot dip coating with iron oxidised
fixture and fastening and painting with 3 coats oil
paints etc. complete. (Sample to be got approved
from Ex. Engineer before use)
Spec.No.: As directed by Engineer- in-charge.
84
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
18 Providing and fixing cold rolled mild steel frame for Sq.m. 1090.00 306.00
BOT door 100 mm x 60 mm of 16 guage as per drawing
135A with/without ventilator including holdfasts, hinges
welded tb the frame, including filling cement mortar
1:6 in hollow core and finishing with oil painting and
tie rod of 12 mm square bar at bottom as per
specification etc. complete.
Spec.No.: As directed by Engineer- in-charge.
19 Providing and fixing door frame of mild steel hot
BOT rolled section of standard EZ-7 conforming to I.S:
135B 7452-1982 as per drawings with/ without ventilator,
holdfasts, hinges welded to the frame and finishing
with oil painting and tie rod of 12 mm square bar -at
bottom as per specification etc. complete. (Sample
to be got approved from Ex. Engineer before use)
20 Providing and fixing pressed steel door box' frame Sq.m. 1031 .00 342.00
of fv1.S.sheet made of 18 guage thick of required
section with rebate of 10 mm for required thickness of
shutters and tie rod of 12mm square bar at bottom as
per specifications with or without ventilators including
holdfasts, hinges welded to the frame, filling in box
frame in C. M. 1:1 0 and finishing with 2 coats of oil
painting etc. complete.
Spec.No.: As directed by Engineer- in-charge.
85
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
24 Providing and fixing 18 guage M.S. sheet door with Sq.m. 1809.00 921.00
frame work 40 x 40 x 6 mm M.S. Angle including
locking arrangements, hold fast including ap-plying
anticorrossive primer coat of red lead paint and 2
coats of oil paint and 12mm square bar at bottom
as per specification complete.
Spec.No.: As directed by Engineer- in-charge.
25 Providing and fixing of approved make PVC door
BOT frame made out of rigid PVC hollow section of
22 required size machine cut with solid polymeric
reinforcement for holding hinges and the rod at
bottom including fixing 1OOmm. Long full threaded
metal screws in required Nos. in PVC roll plugs
inserted in wall as hold fast and remaking damaged
surface etc. complete.
A ) Size 38mm x 32mm Sq.m. 617.00 108.00
B) Size 48mm x 40mm Sq.m. 909.00 153.00
C) Size 60mm x 50mm Sq.m. 1133.00 210.00
Specification : As directed by Engineer-in-charge
86
· SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
26 Providing & fixing of approved make solid Panel of Sq.m. 2715.00 261.00
BOT 29mm thick PVC single leaf door shutter of
25 approved colour and design made out of rigid PVC
hollow section shutter frame in configuration of A
section of size 50mm x 29mm as vertical styles, top &
bottom rails Machine cut and panel in fill of single
panel multi chambers hollow plastic section of size
25mm x 750mm. with solid polymetric 'L' corner
reinforcement holding brackets and solid polymetric
reinforcement fillers for holding hinges, aldrops, latch,
tower bolts, etc. remaking damaged surface etc.
compete .
. Specification -As directed by Engineer lncharge.
27 Providing & fixing of approved make solid Panel of Sq.m. 2351.00 139.00
24mm thick PVCsingle leaf door shutter made out
of rigid PVC hollow section shutter frame in
configuration of A section of size 24mm x 45mm as
vertical styles, top and bottom rails Machine cut and
panel in fill plain multi chamber hollow plastic section
of size 20mm x 200mm joined each other by tongue
and groove inter locking system with polymetric 'L'
corner reinforcement holding, bracket & solid
polymeric reinforcement fillers for holding hinges,
aldrops, latch, tower bolts etc. and remaking
damaaed surface etc.comolete.
Specification : As directred by Engineer lncharge.
28 Providing and fixing single leaf door shutter of Sq.m. 2753.00 361.00
approved make and colour made out of extruded
rigid PVC hollow section DWUF-306 shutter frame
of size 33 mm x 47 mm having double wall
construction as vertical styles, top and bottom rails
and middle locks rail of size 33 mm x 94 mm and the
panel in fill SPUF-101 multichamber hollow plastic
section of size 20 mm x 200 mm joined each other by
tongue and groove interlocking system duly inserted
in shutter frame and all shutter frames, lock rails,
styles reinforced by seasoned wood inserted inside
for fixing of hinges, aldrops, tower bolts and door
stoppers etc. all corners should be Machine cut,
joined each other by metal screw after inserting rigid
"L" bracket PVC reinforcement of size 125 mm x 200
mm. Including synthetic metal fixtures and fastenings,
remaking damaged surface etc. complete.
Spec. No.: As directed by Engineer- in-charge.
87
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
29 Providing and fixing 30mm thick factory made PVC Sq.m , 2917.00 386.00
BOT rigid foam panelled door shutters made of MS
tube 19 guage thickness size 19mm x 19 mm for
styles and 15 mm x 15 mm for top and bottom rails,
covered with heat moulded PVC "C" channel of 5
mm thick sheet and 30 mm x 75 mm wide to form
styles and 5 mm thick and 100 mm wide PVC sheet
for top rail, lock rail and bottom rail on either sides
and 5 mm thick 20 mm wide cross PVC sheet as gap
inserted for top rail and bottom rail, panelling of 5 mm
thick, PVC sheet fitted in MS frame welded I seal to
the style and rails with 5 mm x 30 mm PVC sheet
beading on either side joint together with solvent
cement adhesive etc. complete .
as per manufacturer's specification and direction of
Engineer-In-Charge fixed to the frames with stainless
steel hinges of 75 mm size aluminium tower bolt 100
mm size aluminium aldrop 250 mm size handles 100
mm size including all material, labour, machinery etc
complete. ( For WC I Bath Shutters ) ( the item is
exclusive of door frame.)
Spec.No.:As directed by Engineer- in-charge.
30 Providing and fixing factory made PVC door frame Sq.m 1167.00 171.00
BOT of approved make of size 50 mf'!l x 45 mm with a
wall thickness of 5 mm made out of extruded 5 mm
rigid PVC foam sheet mitred at corners and joined
with 2 nos of 150 mm long bracket of 15 mm x 15 mm
M.S. square tube the vertical door profiles to be
reinforced with 19 mm x 19 mm M.S. square tube of
19 guage EPDM rubber gasket weather seal to be
provided throughout the frame. The door frame to be
fixed to the wall using M.S. screws of 65 I 100 mm
size complete as per manufacturer's specification and
direction of Engineer-In-Charge.
Spec.No.:As directed by Engineer- in-charge.
88
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
33 Providing and fixing FRP ( Fiber reinforced plastic) Sq.m 3430.00 1090.00
BDT Door shutter 25 to 30 mm. Thick having properties
such as water proof resistant to termite resistant to
mild acids and chemical. The thickness of FRP shold
of of 1.5 mm.With extra reinforcement to $ides,
edges, recess for alluminium fixtures and fastenings
and commercial types as per the approved design,
including alluminium , fixtures and fastenings and two
coats of synthetic acrylic emulsion paint etc.
complete (Excluding door frame)
34 Providing and fixing FRP (Fiber reinforced plastic) Sq.m 751.00 188.00
BOT sheet of 1.75 mm. To 2.00 mm. Thick in any colour
for all sizes in windows including , putty, C.T. bedding,
having properties such as water proof resistant to
termite, resistant to mild acids and chemical as per
the approved design etc. complete.
Spec.No.: As directed by Engineer incharge.
35 Providing & fixing of approved make internal PVC I Sq.m 3000.00 244.00
BOT UPVC flush door shutter of 30 mm thick
consisting of frame made out of M.S. tube of 19
gauge thickness and size of 20mm x 40mm for
stiles as well as top, bottom and lock rail. MS frame
shall have a coat of metal primer of approved make
manufacturer. The inside panal shall consist of 20
mm thick multichember hollow PVC section of 1mm
wall thickness,bonded using solvent cement
/cynoacrylate adhesive with 5mm thick plain /prelam
PVC (rigid) sheet of dencity ~00 kg/cum manufacture
by an ISO - 900 certified company, on both side of
inside panai.AII the 4 edges of the panals to be
sealed with lipping of 1Omm thick and 20mm wide
PVC(riQid) sheet batten sheet of 5mm thickness
using solvent cement adhesive.Door edes liping to be
painted with PVC ink of maching colour of plain or
prelam molded PVC sheet of door 20mm thick
(5mmx4mm)thick rigid sheet to be given for lock
provision at lock hight. Door to be fixed frame with 3
Nos stainless steel butt hinges of size 1OOmm x
25mm x 2mm and 50mm long steel screws ·drilled
suitable to pass through both the wall of MS tube.
Other hardware should be fixed with 25mmx8mm size
steel screws etc, complete as per ·direction of
Engineer in charge, manufacturer's specification and
drawing ..
Spec.No.: As directed by Engineer- in-charge.
90
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE
NO. Completed I
(In Rs.)
Labour
ii) With M.S. Box frame of size 40mm x 40mm all Sq.m. 2782.00 342.00
around sheet 2mm thick
B ) with flush Butt welding
i) Without M.S. Box frame Sq.m 2488.00 371 .00
ii) With M.S. Box frame of size 40mm x 40mm all Sq.m 2841.00 3S7.00
around sheet 2mm thick
Spec. No.: Bd.T.53/Page No.509
37 Providing and fixing steel windows of various sizes
BOT as per detailed drawings with welded square bars 12
53A mm at 1Ocm centre to centre without hot dip Zinc
coating without/with ventilator including fabrication,
glazing witti non-acetinic I plain /obscured glass
panels of approved type and quality, all fixtures and
fastenings without teak wood boxing, and architraves
and finishing with one coat of primer complete.
(Sample to be got approved from Ex. Engineer
before use)
A ) with simple welding
i) Without M.S. Box frame Sq.m 3093.00 656.00
ii) With M.S. Box frame of size 40mm x 40mm all Sq.m 3447.00 671.00
around sheet 2mm thick
B ) with flush Butt welding
i) Without M.S. Box frame Sq.m 3279.00 664.00
ii) With M.S. Box frame of size 40mm x 40mm all Sq.m 3627.00 677 .00
around sheet 2mm thick
Spec.No.: As directed by Engineer- in-charge.
91
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed .I Labour
,·
92
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
93
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
42 Providing and fixing M.S. iron bars 16 mm dia for Sq.m 1049.00 215.00
BOT steel windows and ventilators at 1Ocm C/C
120 including M.S. flat 40 mm x Bmm at centre (vertically)
and cutting, welding and painting in two coats of oil
paint etc. complete.
Spec.No.:As directed by Engineer- in-charge.
43 Providing and fixing M.S. iron bars of 16 mm dia for Sq.m 1167.00 229.00
BOT steel windows and ventilators at 1Ocni C/C and
121 M.S. flat 40 mm x 6 mm at sides and 50 mm x 10 mm
at centre in windows and ventilators including cutting,
welding and oil painting in two coatsetc complete.
Spec.No.: As directed by Engineer- in-charge.
94
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
45 Providing and Fixing C.T.W. 2nd class fully glazed Sq.m 6322.00 1644.00
BDT ventilator rectangular in shape as per detailed
4A drawing including iron oxidized fixtures and fastenings
and finishing the wood work with one coat of primer
etc. (with mild steel bars and frame) complete. Prior
permission of S.E.to be obtained for inclusion of
this item in estimate.)
Spec.No.: Bd.T.4/Page No. 479
46 Providing and Fixing C.T.W. 2nd class fully glazed Sq.m 3333.00 931.00
ventilator rectangular in shape as per detailed
drawing including iron oxdized fixtures and fastenings
and finishing the wood work with one coat of primer
etc. (without M.S. bar and frame) complete.(Only
for exterior windows) (Prior permission of S;E.to
be obtained for inclusion of this item in estimate.)
47 Providing and fixing steel ventilator fully glazed Sq.m 2445.00 526.00
BDT partly top hung and partly fixed as per detailed
123 drawing without hot dip zinc coating including
fabricating glazing with plain obscured glass panes of
approved type and quality and fastening without teak
wood boxing and architecture and oil painting two
coats etc. complete. (Sample to be got approved
from Ex.Engineer before use)
Spec.No.: As directed by Engineer- in-charge.
95
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
96
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
51 Providing & fixing of approved make three track Sq.m 3276.00 560.00
BOT PVC sliding Glazed window frame fabricated out of
46 rigid PVC hollow section of size 45mm x 96mm with
concealed solid polymeric reinforcement shall have
mitre cut and fixed with the help of 1OOmm long full
threaded metal screws in PVC roll plugs inserted in
wall as hold fast. Sliding shutter shall be fabricated
out of rigid PVC hollow section of size 45mm x 58mm
and interlocking section of size 5mm x 33mm shall be
fixed on vertical member of sliding shutter. The snap
fit glazing bid of size 21mm x 18.5mm shall be fixed
alongwith sliding shutter for fixing the 5mm thick clear
vision glass panel. Necessary hardware such as
polyester pile seal, rubber gasket, roller bearing and
lock etc. shall be fixed at required junction. Drainage
hole shall be made at the bottom of window frame
etc. and remaking damaged surface complete.
52 Providing & fixing of approved make PVC Louvered Sq.m 2434.00 408.00
BOT I fixed Glazed window I ventilator frame fabricated
47 out of rigid PVC hollow section of size 48mm x 40
mm with concealed solid polymeric reinforcement
shall have mitre cut and fixed with the help of 1OOmm
long full threaded metal screws in PVC roll plugs
inserted in wall as hold fast. The snap fit glazing bid
of size 19mm x 19.5mm shall be fixed alongwith outer
frame for fixing the 5mm thick clear vision glass panel
· or louvered. Necessary hardware such as rubber
gasket, louvered glass holding clip shall be fixied at
required junction etc. complete.
97
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
53 Providing & fixing of approved make sand witched Sq.m 3029.00 488 .00
type PVC partition 50 mm. Thick paneled/partly
glazed in double wall construction made out of
M.S.Rectangular hollow tube section of size 38mm x
25mm with anticorrosive primer vertical horizontal
members not exceeding in the grid of 1m x 1m and
both side wall panels fixed with rigid PVC multi
chamber hollow plastic section of size 6mm x 250mm
in double wall construction and end sealing with rigid
PVC section 71 mm x 20mm. The structure shall be
fixed in floor walls with PVC roll plugs and 1OOmm
long full threaded metal screws including clear vision
plain glass Smm thick as required and door complete
and remaking the damaged surface etc. complete.
55 Providing and fixing partition of 12mm thick three Sq.m 2488.00 418.00
BOT layered flat pressed both side prelaminated teak
66A wood particle board exterior grad~. BWP types
Bonded with phenol formaldehyde synthetic resin
conforming to 1.8.12893-1990 including C.T.W.
vertical 70 x 70 mm and top central and bottom rails
of 70 x 35 mm and covering battens of 20 x 10 mm at
1 m C/C on both ways including finishing with one
coat of primer etc complete.
98
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
58 Providing and fixing partitions of 4mm thick Indian Sq.m · 2076.00 446.00
BOT teak veneers on one side and 4 mm. commercial
83 type plywood on the other side including C.T.W.
frame of 70 mm x 35 mm. at 60 em. C/C including
finishing with french polishing to veneer face and oil
painting/french polishing other face etc. (as per
detailed drawing) complete . (without skirting)
99
.
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
62 Providing and fixing GYP board material stud single Sq.m 1280.00 481 .00
layer partition 97.00 mm thick using single board of
12.5 mm thick on each side of 34/76/36 mm studs
fixed to floor and ceiling channel 70/32 mm at every
610 mm regular interval horizontally including
finishing the joints with jointing compounds, paper
tape and two coats of primer paint etc complete.
64 Providing and fixing 4 mm thick plain A.C. sheets Sq.m 318.00 108.00
BOT on top of the weather shed including scaffolding,
94 fixing by means of nuts and bolts or as directed etc.
complete as per detailed drawing (Brackets of 70 mm
x 45 mm to be paid seperately).
66 Providing and fixing UV proof plastic sheet panels Sq.m 681.00 86.00
of approved quality in required thickness of 3 mm
plain, clear or any colour or obscured (lining) in lieu of
glass panes to doors/windows including providing and
fixing clips, putty etc. complete. (Sample to be got
approved from Ex.Engineer before use)
101
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (Jn Rs.)
NO. Completed I Labour
70 Providing and fixing country teak wood double leaf, Sq.m 4494.00 1370.00
BOT partly panelled and partly glazed door without
11 fanlig ht/ ventilator as per drawings including iron
oxid ised fixtures and fastenings and finishing the
wood work with one coat of primer etc. (excluding
door frame) complete.
Spec.N o.: Bd.T.11/Page No.482
71 Providing and fixing country teak wood 25 mm thick Sq.m 3834.00 1255.00
BOT double leaf second class window with plain/
42 obscured glazed shutters without ventilator or
fanlight as per detailed drawings including iron
oxidised fixtures and fastenings stoppers and
fin ishing the wood work with one coat of primer
(excludin g window frame) complete.
Spec.No. : Bd.T.42/Page No.503
102
BD - U IRON WORK ·
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
103
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
Providing and fixing mild steel grill railing
weighing required kg/Sqm. with PVC
handrail cover and newel post for staircases,
including fabricating; fixtures, drilling holes in
concrete I other surface, erecting the grill
work, necessary welding, fixing by nuts and
bolts, fixing PVC handrail cover, with one coat I
of anitcorrosive paint and two coats of oil
painting with approved colour and shade,
r~making the damaged surface, cleaning, etc.
comolete.
a) --------- do ---------- 20 Kg/Sqm. Sq.m 1642.00 261.00
b)--------- do---------- 25 Kg/Sqm. Sq.m 1923.00 261.00
c) --------- do---------- 30 Kg/Sqm. Sq.m 2197.00 260.00
d)--------- do---------- 35 Kg/Sqm. Sq.m 2488.00 261.00
Spec.No.: As directed by Engineer- in-charge.
4 Providing and fixing mild steel grill work
railing required kg/Sqm. of rectangular
hollow sections with PVC handrail covering
as per drawing including newel · posts for
staircases, drilling holes in concrete/other
surface, fabricating, fixtures, erecting grill work,
necessary welding, fixing by nuts and bolts,
fixing PVC handrail cover, with one coat of
anti- corrosive paint and two coats of oil
painting with approved colour and shade,
remaking good the damaged surface, cleaning
etc. complete.
a) --------- do ---------- 20 Kg/Sqm. Sq.m 1535.00 261.00
b)--------- do---------- 25 Kg/Sqm. Sq.m 1791.00 261.00
Spec.No.: As directed by Engineer- in-charge.
5 Providing & Fixing mild steelgrill railing of
required kg/Sqm. with 50mm dia. MS Pipe
hand rail & sill of 25mm x 3mm & newel posts
for staircases, including fabricating, fixtures,
erecting the grill work with one coat of
anticorrossive paint & two coats of oil painting
of approved colours to the sill, hand rail and
the newel post.
a) --------- do ---------- 20 Kg/Sqm. Sq.m 1462.00 261.00
b)--------- do---------- 25 Kg/Sqm. Sq.m 1746.00 261.00
Spec.No.: As directed by Engineer- in-charge.
104
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
6 Providing & Fixing stainless steel railing with Sq.m 2213.00 294.00
top and vertical pipe of 50mm dia at 0.90 m
c/c or as required and horizontal pipes of
25mm dia in two rows, all pipes of 2 mm thick
including buffing,fa~ricating fixtures and
fast~ning including pipe base of appropriate
diameter and ball base of 75 mm dia above
one major post etc. complete (Prior approval
of sample and brand by Ex.Engineer is
necessary before use)
Spec.No.: As directed by Engineer- in-charge.
105
BD- V: WATER SUPPLY AND SANITARY FITTINGS
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
A ) In trenches
(i) 15 mm dia. Rmt. 314.00 100.00
(ii) 20 mm dia. Rmt. 317.00 100.00
(iii) 25 mm dia. Rmt. 408.00 100.00
(iv) 32 mm dia. Rmt. 451 .00 100.00
(v) 40 mm dia. Rmt. 517.00 100.00
(vi) 50 mm dia. Rmt. 655.00 100.00
(vii) 75/80 mm dia. Rmt. 963.00 124.00
(viii) 100 mm dia. Rmt. 1329.00 149.00
B ) On walls/ ceiling/floors,
(i) 15 mm dia. Rmt. 278.00 69.00
(ii) 20 mm dia. Rmt. 306.00 75.00
(iii) 25 mm dia. Rmt. 377.00 76.00
(iv) 32 mm dia. Rmt. 421 .00 76.00
(v) 40 mm dia. Rmt. 537.00 97.00
(vi) 50 mm dia. Rmt. 685.00 97.00
(vii) 80 mm dia. Rmt. 995.00 97.00
Spec.No.: Bd.V.5/Page No.551
106
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
108
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed ~ Labour
8 Providing and fixing 100 mm dia. Chromium plated No. 375.00 56.00
BDV. brass showers rose to 15 mm dia. Supply pipe
12 including necessary bend and socket, testing etc.
complete. (Prior approval of sample and brand by
Ex.Engineer is necessary before use.)
(a) ------do ------ Swivelling in symet shower No. 226.00 45.00
Spec.No.: Bd.V. 12/Page No.556
11 Providing and fixing fittings and accessories such No. 2244.00 1244.00
BDV as ball cock, over flow pipe with mosquito proof
18 coupling, scour pipe with plug, manhole with cover
and locking arrangement, connecting pipes and
embedding intake and outflow pipes into the R.C.C.
water reservoir.
Spec.No.: Bd.V.18/Page No.558
12 Providing and fixing chromium plated wall mixer Each 2594.00 836.00
cock of heavy duty without washer with chromium
plated showers with/without telephonic arrangement
including necessary supply pipes 15 mm dia. and
fittings like socket union, nuts, bends, valves,
reducers, including necessary drilling holes in walls,
slabs etc and remaking good the demolished
portion to restore the same in original condition
neatly and cleaning the site after completion of
work, testing etc. complete. (S.E.'s permission to
be obtained before execution of this item) (Prior
approval of sample and brand by Ex.Engineer is
necessary before use.)
Spec.No.: As directed by Engineer- in-charge
110
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
A ) White glazed
(i) With 10 litre fibre high level flushing cistern with No. 4745.00 1973.00
fittings
(ii) without flushing cistern with flush cock and No. 4041.00 1726.00
necessary fittings
iii) -- Do-- with metropole flush valve with 40 mm No. 8388.00 2466.00
size and necessary fittings. (Jaquar I Cera I
Johnsons I Hindware or equivalent)
B) Colour Glazed
(i) With 10 litre fibre high level flushing cistern with No. 4984.00 2096.00
fittings
(ii) without flushing cistern with flush cock and No. 4499.00 1973.00
necessary fittings
iii) -- Do-- with metropole flush valve with 40 mm No. 9001.00 2466.00
size and necessary fittings. (Jaquar I Cera · I
Johnsons I Hindware or equivalent)
Spec.No.: As directed by Engineer- in-charge.
111
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
A) White glazed
i) With 10 litre enamelled low level flushing cistern No. 4369.00 1356.00
with fittings.
ii) '--do--with water jet and fittings No. 4894.00 1356.00
iii) without flushing cistern with flush cock and No. 3847.00 1196.00
necessary fittings
iv)--do--- with water jet and fittings No. 4224.00 1356.00
v) --do-- with metropole flush valve with 40 mm size No. 7581.00 1595.00
and necessary fittings. (Jaquar I Cera I Johnsons I
Hindware or equivalent)
vi) --do-- with metropole flush valve with 40 mm size No. 8209.00 1595.00
with water jet and fittings. (Jaquar I Cera I Johnsons
I Hindware or equivalent)
B) Colour Glazed
i) With 10 litre enamelled low level flushing cistern No. 4721.00 770.00
with fittings.
ii) '--do--with water jet and fittings No. 5249.00 1170.00
iii) without flushing cistern with flush cock and No. 4367.00 1244.00
necessary fittings
iv)--do--- with water jet and fittings No. 4901.00 1244.00
v) --do-- with metropole flush valve with 40 mm size No. 8384.00 1463.00
and necessary fittings. (Jaquar I Cera I Johnsons I
Hindware or equivalent)
vi) --do-- with metropole flush valve with 40 mm size No. 9013.00 . 1463.00
with water jet and fittings. (Jaquar I Cera I
Johnsons I Hindware or equivalent)
Spec.No.: As directed by Engineer- in-charge.
112
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
A ) Wh1te glazed
(i) vyith syphonic low level 10 litres UPVC cistern. No. 3935.00 1138.00
(a) With 10 l.itre UPVC high level flushing cistern . No. 4765.00 1702.00
(b) with flush cock and necessary fittings. No. 4500.00 1607.00
c)with metropole flush valve with 40 mm size and No. 7947.00 1891 .00
necessary fittings. (Jaquar I Cera I Johnsons I
Hindware or equivalent)
Spec.No.: As directed by Engineer- in-charge.
113
SR. NO. DESCRIPTION OF ITE~S UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed . , Labour
. . ..
18 Prov1dmg and f1xmg white glazed earthenware No. 2802.00 813.00
sov . semi stall type urinals without cistern, with inlet
110 pipes stop tap, UPVC flush pipe with fittings and
flushing arrangement including UPVC soil pipe,
UPVC trap and soil pipe connection upto outside
face of wall, making good the damaged surface,
testing etc. complete. (Prior approval of sample
and brand by Ex.Engineer is necessary· before
use.)
Spec.No.: As directed tly Engineer- in-charge.
19 Providing and fixing white glazed porcelene ware No. 2128.00 893.00
BDV lipped flat back or corner type urinals without
111 flushing cistern, including glazed soil inlet pipes lead
trap connection , UPVC flush pipe with fittings and
flushing arrangement, including PVC soil pipe,
UPVC trap and soil pipe connection upto the
outside face of the wall, making good the damaged
surface, testing etc. complete. (Prior approval of
sample and brand by Ex.Engineer is necessary
before use.)
Spec. No.: As directed by Engineer- in-charge.
114
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
22 Providing and fixing a group of two white glazed No. 3355.00 1317.00
BDV earthenware lipped flat back type Urinal without
28 flushing cistern, with inlet pipe and stop tap, UPVC
flush pipe with fittings including UPVC soil pipe,
UPVC trap and soil pipe connections upto the
outside face of the wall, making good the damaged
surface, testing etc. complete. (Prior approval of
sample and brand by Ex.Engineer is necessary
before use.)
Spec.No.: Bd.V. 28/Page No. 565
B ) colour glazed
i) With cold water piller tap No. 2861.00 977.00
ii ) With cold and hot water piller tap No. 3230.00 977.00
115
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I
Labour
B ) colour glazed
i ) With cold water piller tap . No. 3125.00 879.00
ii ) With cold and hot water piller tap No. 3839.00 977.00
Spec.No.: Bd.V.30/Page No.565
25 Providing and fixing moulded counter type wash Each 10602.00 1701.00
hand basin including pillar tap, cold and hot water
mixer tap, brackets, rubber plug and brass chain,
stop tap, and necessary pipe connections including,
chromium plated bottle trap, UPVC waste pipe and
trap upto out side face of the walls, making good the
damaged surface, testing etc. complete. (S.E's
prior permission to be obtained before
execution of this item.) (Prior approval of
sample and brand by Ex.Engineer is necessary
before use.)
Spec.No.: As directed by Engineer- in-charge.
26 Providing and fixing high level10 Lit capacity PVC Per No. 1297.00 411.00 ·
cistern with fittings inlet PVC pipe with stop tap,
brackets for fixing the cistern, 32 mm dia. PVC flush
pjpe with fittings and clamps 20 mm dia. PVC
overflow pipe with mosquito proof coupling,
galvanized iron chain and pulley, painting if ordered
to cistern pipe etc. and cutting and making good the
damaged walls and testing etc. complete. (Prior
approval of sample and brand by Ex.Engineer is
necessary before use.)
Spec. No.: As directed by Engineer- in-charge.
27 Providing and fixing white glazed earthenware
BDV sink of required size including all connections of
31A the G.l. supply and UPVC waste pipe and trap upto
the outside face of the wall, cold water chromium
plated screw down bib tap, rolled steel or C.l.
brackets, rubber plug with chain and stop tap,
making good the damaged surface, chromium
plated bottle trap, testing etc. complete. (Prior
·approval of sample and brand by Ex.Engineer is
necessary before use.)
A ) of size 450mm x 300mm x 200mm No. 2060.00 977.00
116
· SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed ILabour
28 Providing and fixing Strainless Steel sink of size No. 3285.00 437.00
BDV 600 mm x 450 mm x 250 mm ( 1 mm thick)
" 300 UPVC waste pipe upto outside face of wall, or upto
nahani tr~p cold water chromium plated screw down
bib tap, rubber plug and brass chain, making good
the damaged surface, etc. complete. (Prior
approval of sample and brand by Ex.Engineer is
necessary before use.)
Spec.No.: Bd.V.30/Page No. 565
29 , Providing and fixing C.l. Nahani Trap (long arm)
BDV of required size including symet grating, bend,
32 connecting piece of C.l. pipe upto the outside face
of the wall, making good the damaged surface,
testing etc. complete. (Prior approval of sample
and brand by · Ex. Engineer is necessary before
use.)
A) 8 em dia No. 891 .00 230.00
117
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
. . . . ..
32 Prov1d1ng and f1x1ng 1n pos1t1on 40 mm. heavy type Rmt. 85.00 23.00
BDV alkathene pipe for drainage connections including
130 cutting, boring holes in wood work or masonry if
necessary, making connections of pipe to sink and
giving test for no leakages, making good the
damaged surface etc. complete. (Prior approval of
sample by Ex.Engineer is necessary before use.)
ii) With Reinforced cement concrete raft in B.C. soil No. 4628.00 770.00
area including cost of reinforcement
B ) Chamber 90 em x 45 em x 60 em
ii) With Reinforced cement concrete raft in B.C. soil No. 7234.00 777.00
area including cost of reinforcement
119
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I
Labour
41 Providing soak pit of size 120 em x 120 em x 120 No. 1173.00 530.00
BDV em including excavating and filling with brick bats as
46 per drawing etc. complete.
Spec.No.: Bd.V.46/Page No.576
42 Providing effluent channel 1.00 M. x 1.00 M., filling Rmt. 414.00 367.00
BDV with boulder 6 em. to 20 em. Size, hand packing and
126 spreading murum at top etc. complete.
120
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
44 Providing and fixing chromium plated towel rod 16 No. 223.00 40.00
BDV mm dia. And 75cm. in length including all
67 accessories complete. (Prior approval of sample
;.:--"' brand by Ex. Engineer is necessary before
use.)
Spec.No.: As directed by Engineer- in-charge.
45 Providing and fixing Glass Shelf 125 mm. Wide and No. 129.00 84.00
BDV 600 mm. long with necessary chromium plated
86 brackets, providing T.W. gutties etc. complete.
Spec.No.: As directed by Engineer- in-charge.
46 Providing and fixing Salt Glazed Stoneware pipe of
BDV required dia including fittings such as bends, tees,
39 single junctions, double junctions, laying, jointing
P-573 (excluding excavation and refilling the trenches)
etc.
A ) 100 mm dia. (Cement: 1.87 kg perm) Rmt. 254.00 85.00
B) 150 mm dia. (Cement: 2.24 kg per m) Rmt. 356.00 85.00
c ) 225 mm dia. (Cement: 4.04 kg perm) Rmt. 387.00 85.00
Spec.No.: As directed by Engineer- in-charge.
47 Providing and fixing cast iron centrifuguly spurn soil/ Rmt. 1228.00 218.00
BDV
vent/ waste pipes of required diameter with
35
necessary fixtures and fitting such as bends, tees,
single junction, double junction, slotted vent offsets
on walls or in the ground including filling joints with
lead with read lead oil paint coat and two coats of
anticorrosive paint including fixing the pipe on walls
by means of nails driven through lugs in wooden
holder/battens and supported on ground floor by
C.C. 1:2:4 of 30 em. x 30 em. size blocks complete.
A) 75 mm Diameter Rmt. 1010.00 208.00
B) 100 mm Diameter Rmt. 1228.00 218.00
Spec. No.: BD.V.35 Page No. 571.
121
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015•16
&CODE (In Rs.)
NO. Complet~d I_ Labour
50 Cleaning septic tank upto 1.5 Cu.m. capacity or No. 1167.00 1035.00
BDV equivalent testing etc. complete.
131
51 Cleaning septic tank more than 1.5 Cu.m. Cum. 296.00 265.00
BDV capacity, add for each additional Cu.m . capacity.
1:\?
Spec. No. : As directed by Engineer- in-charge.
122
BD-W MISCELLANOUS
(a) ANTITERMITE AND PEST CONTROL
PEST CONTROL
3 Providing general pest control service to big size No. 133.00 10.00
inspection chamber to control nuisance of the
cockroaches, etc. complete during years with
monthly check up.
Spec. No.:- As directed by Engineer In Charge
123
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Compl.eted I
Labour
...
Providing Preconstruction Anti-termite treatment Sq.m 125.00 13.00
by treating the back fill in immediate contact with
foundation at the rate of 5 litres of an emulsion
concentrate of one percent concentration of
CHLORPYRIFOC 20% EC lSI approved,
conforming (I.S. 8944) to per square metre of
verticle surface area by high volume sprayer with
ten years guarantee bond as per I.S. 6313 (Part II)
cl1~1 .
Spec. No.:- As directed by Engineer In Charge
124
SR. NO. DESCRIPTION OF ITEMS .. UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO. Completed I Labour
2 Guniting by dry mix process as per I.S. 9012 Sq.m. 1066.00 151.00
BOW (1978) to ceilings,soffit & sides etc. in
43 C.M. 1:3 proportion with admixture (guniting
aid ie microsilica or sifumex-1 00 D powder)
and 50 mm thick under pressure 2.1 kg to
2.8 kg per Sq. em. including welded mesh of
size 75 mm x 75 mm x 10 guage as
reinforcement with fixing by anchor bolts with
forms, scaffolding, curing for 14 days etc.
complete.
Spec.No.: As directed by Engineer- in-charge.
4 Providing and fixing welded mesh fabric for Sq.m. 258.00 94.00
guniting of mesh size 75 mm x 75 mm and
10 gauge thick including scaffolding etc.
complete.
Spec.No.: As directed by Engineer- in-charge.
126
SR. NO, DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
127
(c) FENCING WORK
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
Completed I Labour
3 Providing and fixing mild steel grill gate with angle Sq.m. 2119.00 115.00
BDW iron frame 65 mm x 65 mm x 10 mm with iron bars at
6 150 mm C/C and diagonal flats as per the detailed
drawing including hinges, pivot blocks locking
arrangement welding, revetting with oil' painting in
three coats of approved colour shade. {Weight of
gate 35 kg/Sq.m.)
Spec.No.: Bd.W.6/Page No.585
4 Providing and erecting 1.20 m. high chain link Rmt. 705.00 130.00
fencing with chain link having hole size 65 mm x 65
mm supported on M.S. angle post of size 50 mm x 50
mm x 6 mm with M.S. flat of size 50 mm x 5 mm for
fastening chaifl link with post angle at 2.40 m c/c
including, excavating pits for foundation fixing post in
C.C. 1:4:8 of size 45 em x 45 em x 45 em fixing
chain link with 3.25 mm ( 10 guage ) G.l. wire and
M.S. flat of size 40 mm x 5 mm provided at top and
bottom and with oil paint etc. complete.
Spec. No.: As directed by Engineer- in-charge
·.
,...
/ 128
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&CODE (In Rs.)
NO.
. Completed I Labour
5 Providing and erecting 1.20 mtr high welded Rmt. 733.00 90.00
square mesh fencing with welded square mesh of 3
mm thick G. I. wire &having hole size 40 mm x 40 mm
supported on M.S. angle post of size 50 mm x 50
mm x 6 mm as with M.S. flat of size 40 mm x 5 mm
nut bolted with support angle including fixing post in
C. C. 1:4:8 block and fastening with welded square
mesh painting the exposed structural steel work etc.
complete ..
Spec. No. :As directed by Engineer- in-charge.
7 Providing & Erecting U-type barbed wire fencing Rmt. 769.00 82.00
with seven rows of wire with 2.45 mm dia. G. I. pipe
(R~zan/ concentina wire 0.75 mm dia.) with hot dip
& G.l. coated hooks as per drawing supported on
M.S. angles 50 x 50 x 6 mm at 2.5 mtr. c/c including
fixing & fastening with wire, painting M.S. angles with
one coat of red lead primer & two coat of oil paint
etc. complete.
Spec.No. :As directed by Engineer- in-charge.
129
(d) DISMANTALING
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
.
Completed l Labour
3 Removing Manglore tiled roof and ridge tiles Sq.m. 52.00 47.00
BDW with battens, ridge and barge boards, eaves
8A boards etc. and stacking the materials as
directed with all leads and lifts complete.
Including removing wood work below.
Spec. No.: As directed by Engineer- in-charge.
130
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 201.5-16
& (In Rs.)
CODE
NO. Completed I Labour
7 Removing R.S.girders of any size and span M.T. 1187.00 1069.00
lowering the same and stacking neatly where
ever directed in compound, scaffolding etc.
complete for all height.
Spec. No.: As directed by Engineer- in-charge.
8 Dismantling the R.C.C. work 1:2:4 and sorting Cu.m. 1030.00 927.00
BOW out the materials such as steel etc. as directed
8-30 and stacking them within the specified lead as
directed.
Spec.No.: As directed by Engineer- in-charge.
10 Removing queen post truss from roof and No. 218.00 197.00
BOW stacking the materials as directed with all
8E leads and lifts etc. complete.
Spec. No.: As directed by Engineer- in-charge.
11 Removing king post truss from roof ancl No. 155.00 140.00
BOW stacking the materials as directed with all
8F leads and lifts etc. complete.
Spec. No.: As directed by Engineer- in-charge.
131
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
14 Removing cloth ceiling including frame work Sq.m. 13.00 12.00
BOW and stacking the materials as directed with all
8K leads, lifts etc.complete.
Spec. No.: As directed by Engineer- in-
charge.
132
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
21 Removing doors and windows with frames No. 101.00 91.00
BOW and stacking the materials as directed with all
8-1G leads, lifts etc. complete.
Spec.No. : As directed by Engineer- in-charge.
133
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
28 Dismantling brick masonry in mud mortar Cu.m. 117.00 105.00
BOW and stacking the materials as directed with all
8-1 leads, lifts etc. complete.
Spec. No.: As djrected by Engineer- in-charge.
134
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
34 Removing rich mix cement concrete Cu.m. 865.00 778.00
BOW including stacking the spoils as directed with
8-1E all leads, lifts etc. complete.
Spec.No.: As directed by Engineer- in-charge.
37 Removing trap stone from floor without bed Sq.m. 42.00 38.00
BOW concrete including stacking the materials as
8-2A directed with all leads, lifts etc. complete.
135
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
41 Removing Urinal Pans or W.H.B. with frame No. 69.00 63.00
BOW including disconnecting the sanitary and water
15 supply connections, removing the same
carefully and stacking the serviceable
materials as and where directed including
throwing the unserviceable materials outside.
Spec. No.: As directed by Engineer- in-charge.
136
· BRIDGE .
WORKS
BR BRIDGE WORK
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
137
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Co~pleted I Labour
138
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
I 3__)
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
140
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
11 Providing and laying in situ C.C. M-15 /1:2:4 of Cu.m. 4120.00 612.00
trap I granite I quartzite I gneiss metal for
annular filling around pier I abutment including
necessary bailing out water, excluding
dewatering by pump compaction by vibrating
finishing uneven and honeycombed surface with
C.M.1 :3 of sufficient minimum thickness to give a
smooth and even surface or roughening the
surface if special finish is to be provided, curing
etc. complete. The C.M. 1:3 plaster is considered
for rendering uneven and honeycombed surface
only. Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc.
Spec. No: BR.5/Page No.1 05/1.8.456 (2000)
'141
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
142
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& · (In Rs.)
CODE
NO.
Completed I Labour
15 Rmt. 44.00
BR diameter and of required length for relieving
5G water pressure, stbne filter as directed
complete.(For relieving water pressure in raft
abutment riding returns).
Spec,No.: As directed by Engineer- in-charge.
19 Providing fabricating and setting out mild steel M.T. 61701.00 8059.00
BR cutting edges for R.C.C well curbs as shown on
10 the detailed drawings,
Spec. No.: BR.1 0/Page No.11 0
143
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
· NO.
..
Completed I Labour
. 144
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
145
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
. 146
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
25 Providing steel anchor dowels in rock for No. 5521 .00 627.00
BR · steining, including drilling holes upto 2.5 m.
16A depth in rock, placing dowels in position and
effectively grouting holes ( 32 mm diameter steel
rod of 4.0 m length grouted upto 2.5 m
Spec. No.: BR.16/Page No.120
26 Providing and laying in situ C.C M-15 of trap I Cu.m. 4743.00 788.00
BR17 granite I quartzite/ gneiss metal for the bottom
plugs of wells in the dry or under water including
compaction and curing wherever necessary.
Spec.No.: BR.17/Page No.120/I.S.456 (2000)
27 Providing and filling in well with sand/rubble Cu.m. 458.00 98.00
BR and sand/shingle and sand including
18 compaction between the top and bottom plugs. (
Including Royalty charges)
Spec.No.: BR.18/Page No.122
28 Providing and laying in situ c·.c. M-15 I 1:2:4 of Cu.m. 4644.00 1073.00
BR trap I granite I quartzite I gneiss metal for top
19 plug of well including compaction by · vibration
and curing.
Spec.No. : BR.19/Page No.123/I.S.456 (2000)
29 Providing and laying in situ C.C.of required
BR grade of trap I granite I quartzite I gneiss metal
24 for R.C.C. well/ pile cap including plywood/ steel
formwork and steel, centering, compaction by
vibrating finishing uneven and honeycombed
surface with C.M.1:3 of sufficient minimum
thickness to give a smooth and even surface or
roughening the surface if special finish is to be
provided, curing etc. complete. (Excluding M.S.
reinforcement · and including shuttering &
cover block) The C.M.1 :3 plaster is considered
for rendering uneven and honeycombed surface
only. Newly laid concrete shall be covered by
gunny bag, plastic, tarpaulin etc. (Wooden
centering/ formwork wiil not be allowed).
147
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
. . .. ..
Completed I Labour
( 8 )For M-25
148
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
( C )For M-30
( D )For M-35
149
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
. .
Completed I Labour
150
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
151
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
Note:
Add for height above 3m to Sm. - 5% (Above
average bed level)
Add for height above 6m. - 10% (Above
average bed level)
Spec.No.: BR.38/Page No.135/I.S.456 (2000)
152
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
Note:
Add upto height above 3m to 6m. - _5% (Above
average bed level)
153
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
GODE
NO.
Completed I Labour
Note:
.i) Add upto height above 3m to Sm. - 5%
(Above average bed level)
154
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
155
SR. NO. - DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
A ) Excluding reinforcement
156
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (lt:'l Rs.)
CODE
NO.
Completed I Labour
157
I
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
158
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015.:16
& (In Rs.)
CODE
NO.
..
Completed I La~our
53 Providing removable railing of height 1.10 m Rmt. 2054.00 63.1.00
BR with mild steel channel size 75 mm x 40 mm of
51D Ht.1.225 mt. above top of road surface posts and
removable galvanised iron pipe of dia 37.5 mm 3
nos. at distance 370 mm C/C and bottom bar 150
mm above kerb as per the detailed drawings
including scaffolding and painting etc. complete.
54 Providing railing of cast in situ R.C.C posts with Rmt. 1237.00 165.00
BR 1 :2:4 (M-15) cement concrete trap I granite I
51E quartzite I gneiss metal size 150 mm x 150 mm
x 1.240 mm and removable galvanised iron pipes
of dia. 37.5 mm 3 nos. at distance 370 mm .C/C
and bottom bar 150 mm above kerb as per the
detailed drawings (including cost of
. reinforcement) scaffolding,steel centering,
plywood/steel forrnwork etc. complete. The C.M.
1:3 plaster is considered for rendering uneven
and honeycombed surface only. Newly laid
concrete shall be covered by gunny bag,
plastic, tarpaulin etc. (Wooden
centeringlformwork will not be allowed).
159 I
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
160
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed I Labour
.. . .
4183.00 1773.00
60 Prov1dmg and f1x1ng marble tablet of s1ze and Sq.m .
BR description as per detailed drawings including
56 moulded marble I 1:2 C.M. border.
Spec.No.: BR.56/Page No. 150
62 Providing and filling sand below raft and in box Cu.m. 370.00 53.00
BR return including watering and compaction
57A etc. complete.
Spec. No.: As directed by Engineer- in-charge.
63 Providing 90 em thick flexible stone mat as per Sq.m. 747.00 205.00
BR standard drawing including supplying all materials
578 at work site spreading and compaction etc.
complete.
Spec.No.: As directed by Engineer- in-charge.
.
65 Supplying, fitting and fixing in position true to line Tonne 233.00 57.00
and level sliding plate bearing with PTFE capacity
surface sliding on stainless steel complete
including all acce~sories as per drawing and
Technical Specifications and BS: 5400, section
9.1 & 9.2 (for PTFE) and clause 2004 of
MORT&H Specifications etc. complete.
Spec. No. :M.O.R.T.& H. 2001 Clause No 2000
161
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
. .
Completed I Labour
162
CROSS
DRAINAGE
WORKS .
C.D. :- CROSS DRAINAGE WORK
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
&
. (In Rs.)
CODE
NO. Completed I Labour
163
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
Diameter of pipe
A) NP-2 Class
i) 300 mm. Rmt. 980.00 167.00
il) 450 mm. Rmt. 1164.00 221.00
iii) 600 mm. Rmt. 1778.00 294.00
iv) 800 mm. Rmt. 2825.00 329.00
v) 900 mm. Rmt. 3610.00 346.00
vi) 1000 mm. Rmt. 4258.00 458.00
vii) 1200 mm. Rmt. 5905.00 576.00
B) NP- 3 Class
i) 450 mm. Rmt. 2492.00 421.00
ii) 600 mm. Rmt. 3425.00 421.00
iii) 800 mm. Rmt. 5558.00 481.00
iv) 900 mm. Rmt. 5821.00 571.00
v) 1000 mm. Rmt. 6808.00 700.00
vi) 1200 mm. Rmt. 9353.00 775.00
C) NP- 4 Class
i) 1000 mm. Rmt. 8306.00 .652.00
ii) 1200 mm. Rmt. 10595.00 761.00
Spec. No. MORT & H 2001 Clause -2901 Page
No.663
164
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
165
· ROAD
WORKS
5 RD .. ROAD WORKS
5(A) EXCAVATION AND EMBANKMENT
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed IL~bour
1 Cutting down trees including trunks and
RD branches and removing wood upto 1 meter below
1 ground level and stacking the materials neatly with
a lead of 50 m as directed with specified girths
etc. complete.
(a) For earth soil of all sorts, sand, gravel, & Cu.M. 69.00 5.00
soft murum · ., .
(b) For hard murum, hard murum with boulder Cu.M. 89.00 6.00
166
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
0 0
167
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
..
Completed I Labour
6 Prov1dmg earth work in embankment w1th Cu.M. 94.00 6.00
approved Fly ash obtained from Thermal
power plant including all lifts and leads upto
50.00 m loading unloading laying in layer of which
loose thickness shall not exceed · 200 mm.,
breaking clods of covered soil, dressing to
required lines, curves, grades & section, watering
and compaction with power roller including
providing earth work over it for minimum thickness
of 0.50 m on top and 1.0 m on side slopes
including without any flooding & compaction
..;ompiete. The soil cover of required width be
provided with the core and mechanically
compacted simultaneously so as to have thorough
compaction of each layer of Fly ash to the
specified density as stipulated in IRC SP 58 2001
(Transportation charges for fly ash shall be
considered separately for 0.60 Cum. quantity of fly
ash only for per cum. of embankment) etc.
complete.
7 Excavation for roadway in earth soil of all sorts Cu.m. 110.00 97.00
RD sand, gravel or soft murum including dressing
2 sectioning to the required grade, camber and side
slopes and conveying the excavated materials
with all lifts and upto a lead of 50 m and spreading
for embankment or stacking etc. complete.
168
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
169
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
13 Excavation for catch water gutter in all sort of Cu.m. · 119.00 107.00
RD soils, soft murum by manual means to the
9A specified section including stacking the excavated
stuff in regular bund and disposing off unsuitable
or excess stuff upto a lead of 50 m and spreading
etc. complete.
Spec.No. : Rd.9/Page No.187
17 Excavation for catch water gutter in hard rock Cu.m. 562.00 170.00
RD by wedging & chiseling to the specified section
90 including stacking the excavated stuff in a regular
bund and disposing off unsuitable or excess stuff
etc. complete.
Spec.No. : Rd.9/Page No.187
170
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
18 Excavation for widening of metal strips from 3.0 Cu.m. 118.00 9.00
RD m. to 5.5 m. width in all soils including dressing
9F section to the required grade, camber and side
slopes and conveying the excavated materials
with all lift upto a lead of 50 m. and spreading for
embankment or stacking etc. complete.
171
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
23 Compacting the earth work obtained from road Cu.m. 12.00 1.10
cutting , excavation of road side drain by Static
roller having weight 8 to 10 MT. and watering etc.
Complete
As directed by Engineer- in- charge.
172
5(8) WBM Road Construction
breaking boulders.)
Spec. No.: Rd. 19/Page no.197
3 r
SUpJ?Iying trap /granite /quartzite gneiss stone
RD metal of required size by bringing the boulders
19A at the road side breaking them to required
gradation including conveying the boulders and
stacking the broken metal etc. complete. (Prior
approval of sample stack of broken metal by
the Ex.Engineer is necessary, the date of
approval will form part of the measurements)
4 Supplying murum having PI < .S at the road side, Cum. 374.00 60.00
RD including conveying and stacking complete.
23
Spec.No.: Rd.23/Page No.202
5 Supplying soft murum at the road side, including Cum. 342.00 60.00
RD convevina and stackina comolete.
24 Spec.No.: Rd.24/Page No.203
173
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
6 Supplying sand at the road side, including Cum. 374.00 60.00
RD conveying and stacking complete.
25
Spec.No.: Rd.251Page No.203
'
11 Spreading 40 mm metal including sectioning Cum. 54.00 48.00
RD complete.
29
Spec.No.: Rd.291Page No.205
174
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
13 Picking the road surface including sectioning Sqm. 6.00 6.00
RD complete. (WBM suface)
33
Spec.No.: Rd.33/Page No.208
175
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
176
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.}
CODE
NO. Completed I Labour
25 Providing pick and roll surface by picking the Sqm. 55.00 35.00
old WBM surface to the required standard,
adding 30% of 40mm size metal and required
quantity of murum including laying sectioning,
watering, compacting with Static roller having
weight 8 to 10 MT. with thin layer of murum
blindage on carrageway, watering and compacting
by static roller, including cost of all materials,
loading, unloading, stacking and labour etc.
complete.
Spec. No. :As directed by Engineer- in-charge.
,·,
177
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed l Labour
(a} For grade I material, using stone screening Cum. 1255.00 222.00
type 8
(b) For grade II material, using stone screening Cum. 1300.00 222.00
type 8
Spec. No. M.O.R.T.& H. Cl. 404 .P.No.121.
28 Providing and. laY.ing Tech fab India CE marked Sqm. 97.00 19.00
MORT Needle Punched and mechanically bonded non
H 700 woven Geotextile indigenously manufactured
from high quality poly Propylene staple fibers
(continuous filament will not be accepted) on the
prepared subgrade for Seperation. TFI-TECH GO
=
PR-15
Spec. No. :M.O.R.T.& H. 2013. Cl. 700.
178
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
29 Water Bound Macadam (WBM) ( For Patch
Repairs Only)
Filling pot holes & patch repairs by Providing,
laying, spreading and compacting crushed stone
aggregates of specific sizes to water bound
macadam specification including making good
disturbed I erroded I undulated portion on
existing road surface. The undulations I
patches I errossion formed on existing road
surface shall be developed in regular shape
such as a square or a rectangle as per demand
of the erroded shape using chisel, making
walls of the dipression I pot holes verticle on
all sides , taking photographs I video for such
spots before , during execution & after
execution of work & loading the same on
computer of sub Division I Division office etc.
complete spreading in uniform thickness, hand
packing, rolling with Static roller having weight 8-
10 tonnes in stages to proper grade and camber,
applying and brooming requisite type of screening/
binding Materials to fill up the interstices of coarse
aggregate, watering and compacting to the
required density as directed etc. complete.
For metal Grading - II Using stone screening Cum. 1320.00 305.00
type 8 (13.2 mm agg.)
Spec. No. M.O.R.T.& H.2013. Cl. 404 .P.No.121.
179
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed l Labour
31 Labour for metal patch repairs including Sqm. 33.00 33.00
RD75 preparing surface , adding required quantity of
metal , murum watering , ramming etc. complete.
Spec.No.: RD 75
32 Labour for screening metal chips etc. Complete. Cum. 41.00 23.00
R076
Spec.No.: RD 76
180
5(C) ASPHALTIC CONSTRUCTION
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
181
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed ·I Labour
182
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
183
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
' Completed l Labour
. 184
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed
. .
I Labour
185
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
Built-up-Spray Grout
9 Providing, laying and compacting of built-up- Sqm 258.00 1.50
spray grout layer 75 mm thick over prepared
base consisting of two layesr composite
construction of compacted crushed coarse
aggregates with application of bituminous binder
of VG-30 Grade @ 1.520 Kg/ Sqm after each
layer, ( i.e 1.520x2=3.04 say 3.00 Kg/Sqm) and
with key aggregates placed on top of the second
layer and compacting with static roller 8 to 10
Mt. Including cost of tack coat and scarifying etc.
Complete.
186
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed 1
Labour
187
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
0 0
Completed I Labour
a) Drum mix plant with paver finisher without Sqm . . 65.00 8.00
SCADA
b) Drum mix plant with paver finisher with Sqm 66.00 8.00
SCAD A
14 Providing & applying tack coat of Bitumen VG-10 Sqm. 17.00 2.00
grade @ 0.30 Kglsq·m. on BT Surface I granular
surface treated with primer I cement concrete
pavement by mechanical sprayers including
cleaning surface, conveying, heating and cost of
bitumen etc. complete.
15 Providing & applying Prime coat with Bitumen Sqrri. 39.00 3.00
VG-1 0 grade on WBM I WMM of granular base ,
spraying bitumen @ 0. 75 kglsqm with the help of
self propelled or towed bitumen pressure sprayer
equiped with suitable nozels to achive uniform
dose, including cleaning of road surface by power
mechanical sweepers etc. complete.
188 '
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
.CODE
NO. Completed I Labour
189
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
' 190
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE ·
' NO. Completed I Labour
. .
20 Prov1d1ng and laymg Hot Mix Hot Laid
Bituminous Macadam of thickness 50 to 75
mm with 3.4 % bitumen of VG 30 Grade by
weight of total mix for levelling course to remove
irregularities, including all material and crushed
aggregates of grading II, premixed with bituminous
binder, heating bitumen and chips in hot mix plant,
transported to site with VTS, laying bituminous
macadam over a previously prepared surface
including diversion of traffic, finished to the
required grade, level, alignment and rolling to
achieve the desired compaction with vibratory
roller to achieve the desired compaction as per
MORT&H specification complete in all respect
Using 80-120 TPH Batch mix type hot mix plant.
( Excluding cost of tack coat )
a) Batch mix plant with paver· finisher with Cum 5848.00 49.00
SCADA
b) Batch mix plant with hydrostatic senser Cum 5906.00 49.00
paver with SCADA
Spcef.No.-M.O.R.T. & H. No.504 I P.No.170
191
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed 1
Labour
192
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
193
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
Completed Labour
NO.
23 Providing and laying Bituminous Concrete of
thickness 30 to 40 mm on prepared surface with
specified graded crushed stone aggregates
premixed with Bitumen of VG 30 Grade and 2%
filler as cement by total weight of aggregate as per
Job Mix, including diversion of traffic, heating
bitumen and chips, mixing bitumen, chips and filler
in drum mix plant, transporting the mix to the
work site to the required grade, level and
alignment, compacting with vibratory roller to
achieve the desired compaction as per MORT&H
specification complete in all respect excluding
cost of tack coat. ( The rate is for Bitumen content
@ 5.4 % by weight of total mix)
a) Drum mix plant with paver finisher without Cum 8188.00 52.00
SCADA
b) Drum mix plant with paver finisher with Cum 8245.00 52.00
SCADA
c) Drum mix plant with hydrostatic senser Cum 8265.00 52.00
paver without SCADA
d) Drum mix plant with hydrostatic senser Cum 8307.00 52.00
paver with SCADA
194
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
195
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed 1 Labour
. .
27 Prov1d1ng, lay1ng and compacting of Close-
Graded Premix Surfacing I Mixed Seal
Surfacing · of 20 mm thickness composed of
13.2 mm to 0.09 mm (Type-B) aggregates using
bitumen of ( VG-30 Grade) for Type B @ 1.90
KgiSq.m for mixing to the required line, grade
and level to serve as wearing course on a
previously prepared base, including mixing in a
hotmix plant, laying bituminous mix with paver
finisher and compacting with static roller having
weight 8-10 MT., finishing to required level and
grade including cost of tack coat of VG-1 0 grade
bitumen@ 0.30 Kg I Sqm on B.T. surface.
a) Drum mix plant with paver finisher without Sqm. 128.35 2.00
SCADA
b) Drum mix plant with paver finisher with Sqm 128.75 2.00
SCADA
c) Drum mix plant with Hydrostatic sensor Sqm 129.60 2.00
paver with SCADA
d) Drum mix plant with Hydrostatic sensor Sqm 135.05 2.00
paver without SCADA
a ) Batch mix plant with paver finisher with Sqm. 130.10 2.00
SCADA
b ) Batch mix plant with Hydrostatic paver Sqm. 131.25 2.00
finisher without SCADA
Spec. No. M.O.R.T.& H 2013. CI-508.P.N.192.
196
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
197
SPECIFICATIONS FOR BITUMINOUS BOUND MACADAM I MPM
Item : Providing and laying 50175 mm thick bituminous bound macadam (BBM I MPM)
road surface including supplying all materials, preparing the existing road surface,
spreading 40 mm stone metal layers, heating and spreading the bitumen, spreading 12
mm size chips, compacting with power roller etc. complete.
(a) Including picking of existing WBM surface.
(b) Including applying tack coat at the rate of 50 Kg I 100 Sqm on existing bituminous
surface.
1. General
The work consists of supply of all materials and labour required for providing and laying
bituminous bound macadam surface for compacted thickness of 50175 mm. The item
includes preparing the existing road surface to receive the bituminous bound macadam
course,. spreading of 40 mm size hand broken metal laying in required thickness with
compacted with static roller, heating and spraying bitumen with equipment plant etc.
spreading key aggregates, 12 mm chips and final compaction with static roller etc.
complete. The work shall be finished in accordance with the requirement of this
specification and in dose conformity with grades, lines, cross sections and thickness as
per approved drawings or as directed by the Engineer in charge.
2. Diversions
Temporary diversions shall be constructed and maintained by the contractor at his own
cost. Diversions shall be watered if dust is likely to blow on to the road being
bituminised.
3. Materials:
(A) Aggregates: The aggregates for providing B.B.M. I M.P.M. su rface shall comply
with specification Nos. Rd-41 for 40 mm and 12 mm size metal, and shall normally
comply with the following according to size and quality of aggregate and grade and
quantities of bitumen·
Rate of application for 100 Sqmt.
Description 75mm 50mm
On OnW.B.M. On asphalt OnW.B.M.
asphalt Surface surface Surface
surface
a) 40 mm size hand 9.00 9.00 Cum 6.00 Cum 6.00 Cum
broken metal Cum
bl 12 mm size chips 1.80 Cum 1.80 Cum 1.20 Cum 1.20 Cum
c) Bitumen for 200 Kg 200 Kg 175 Kg 175 Kg
grouting I.S.grade
S35 with VG-40
(30140f penetration
or S 65 with VG-30
(60170)
d) Tack coat for 50 Kg -- ' 50 Kg --
existing bituminous
surface.
Note:- Hand broken metal IS preferred. However upto 30 % of total quality of 40
mm size metal, 40 mm crusher broken metal can be used.
(B) Bitumen : The bitumen shall be paving bitumen suitable penetration grade
within the range S 35 to S 65 or A 35 to 65 (VG-40 to VG-30) (30140 to 60/70) as per
Indian Standard Specification for 'Paving Bitumen' IS: 73-1992.
198
4. Preparing the base :
Any pothole in the existing bituminous road surface and broken edges shall be patched
well and the surface shall be brought to correct level and camber with additional metal
and bitumen as required which will be paid separately. Before starting the work the
bituminous surface shall be swept clean of all the dirt, mud cakes, animal droppings &
other loose foreign material.
If so required by the Engineer, the contractor shall keep the side width & nearby
diversion watered to prevent dust from blowing over the surface to be bituminised.
Existing water bound macadam surface shall be picked for and surface loosened for a
depth of 2.5 em and the picked surface shall be brought approximately to the correct
camber and section Edge line shall be correctly marked by dog belling the surface to
form a continuous vee notch.
There shall always be sufficient length of prepared surfac~ ahead of the bituminous
surfacing operations as directed by the Engineer to keep these operations continuous .
8. Application of Bitumen :
Bitumen of I.S.grade 8.35 or 8.35 supplied for the work shall be heated to temperature
of 177 Celsius to 191 Celsius (350 F to 375 F) in a bitumen boiler and temperature shall
be maintained at the time of actual application. The hot bitumen shall be applied
through a pressure sprayer on the road surface uniformly at the rate of 200 Kg I 100
Sqmt. or 175 Kg I 100 Sqmt. The road surface shall be divided into suitable rectangles
marked by chalk so as to ensure correct rate of application of the bitumen.
199
9. Key Aggregates:
On completion of bitumen application, 12 mm size key aggregate shall be spread
immediately at a uniform rate of 1.8 cubic meter I 1.2 cubic meter per 100 square meter
of area when entire surface is in hot condition. Brooms shall be used to ensure even
distribution of key aggregate.
3 Flankiness Index and One test per 200 cubic meter of aggregate.
Elongation Index
4 Stripping value Initially one set of three representative specimen
for each so urGe of supp!)' subsequently when
warranted by changes in the q1~_1iity: of aggregate.
5 Water absorption of Initially one set of three representative specimen
aggregates for each source of supply subsequertly when
warranted by changes in the quality of ag!Jregate.
6 Aggregate grading One test per 200 cubic meter of aggregate.
7 Temperature of binder at At regular c~ose intervals.
application. -
8 Rate of spreading for One test per 500 cubic meter of area.
binder
13. Mode of Measurement and payment: The contract rate shall be for 100 Sqm. The
measurements shall be for the width of the road as executed, limiting it to the width
specified or as ordered by the Engineer and the length measured along the center line.
The measurement dimensions shall be recorded correct upto two places of decimals of
a meter and the area worked out correct upto one place of decimal of a Sqm.
200
5(0) CONCRETE PAVEMENT
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015•16
& (In Rs.)
-
CODE
NO. Completed
-
I Labour .
B) Without paver
a) M-30 Grade Cu.m. 5169.00 21.00
201
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Lab ur
..
2 Prov1d1ng and lay1ng ready mix Cement concrete
pavement of specified grade with 20% fly Ash
of trap I granite I quartzite /gneiss metal including
mixing in ready mix plant of approved make
including transportation of concrete mix for
wearing course including plywood/steel
formwork, steel centering and compaction by
vibrating using plate, needle and screed vibrator
as required grooming the concrete surface to get
serrations leveling to the surface as directed &
curring etc. complete including use of plastisizers
and retarders as directed by engineer in charge
(excluding cost of reinforcement) Newly laid
concrete shall be covered by gunny bag, plastic,
tarpolin, etc. (Wooden centering I formwork will
not be allowed) as per specification given and
directed by Engineer in charge. Item includes
cement vata in CM 1:8 at 0.60 m x 0.60 m centre
to centre admeasuring 80 mm at bottom and 40
mm at top & depth of 75 mm and maintaining the
same throughout 28 days curring period and
removing the same thereafter by using light tool
without damaging pavement
B) Without paver
a) M-30 Grade Cu.r:n. 4970.00 21.00
202
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
·s Providing and fixing in position HYSD tie bars No. 30.00 5.00
precoated with anticorrosive epoxy paint of 12
mm dia. 70 cms.long and at 30.00 em. C/C &
wherever directed including handling,
straightening wrapping with paper of approved
quality for half length, necessary cutting, handling,
straightening , supported by assembly of HYSD
chairs with proper alignment etc. complete.
203
' SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
- - - -
6 Cutting transverse contraction joints 3 to 4 mm Rmt. 68.00 28.00
wide and depth 60mm .. in concrete slab using
concrete cutting machine with diamond studded
saw within 48 hours of casting of bay I slab etc.
complete including subsequent widening of the
groove 8 to 10 mm. wide at top having depth of 15
mm. as directed by Engineer incharge.
204
5(E) PROTECTION WORKS GEOSYNTHETICS
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
205
S(F) ROAD FURNITURE
- --
SR. NO, DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
1 Providing and fixing R.C.C. 1:2:4 boundary stone No. 824.00 209.00
of siz;e (15 X 15 X 90 em ) including cost of
reinforcement @ 100 kg I Cum as per type design
inclu.ding painting, numbering, fixing in standard
§it.:e (45 X 46 X 75 em ) C.C. 1:4:8 block etc
c;omplete.
Spec. No.: M.O.R.T. & H.2013 CL.807.P.No.357
2 Providing and fixing R.C.C. 1 :2:4 200 m. stone No. 341.00 110.00
of siz.~ (16 X 10 X 65 em ) as per I.R.C. design
(IRC 26~1967) including cost of reinforcement @
1QO kg I cum), painting, numbering, fixing in
standard size (35 X 30 X 40 em) C.C. 1:4:8 block
etc complete.
Spec. No. : M.O.R.T, & H. 2013 CL.807P.No.357.
3 Providing R.C.C. 1:2:4 5'th Km. Stone on S.H No. 2909.00 515.00
and M.D.R. etc. including cost of reinforcement @
100 kg I cum), painting, numbering etc. complete
as per IRC design (IRC 8~1980) for highway 5th
km. Stones and fixing in standard size (55 X 80 X
60 em) C. C. 1:4:8 block etc complete.
206
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
5
. . .
Provrdrng R.C.C. 1:2:4 ordmary km. stones, for No . 1498.00 536.00
ODR and V.R. including cost of reinforcement@
100 kg I cum) painting numbering etc .. complete as
per I.R.C. design (IRC 8-1980) for highway
km.stone and fixing in standard size (67 X 50 X 60
em ) C.C. 1:4:8 block etc complete.
207
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
208
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
209
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
10 Overhead Signs
Providing and erecting Overhead signs with
required sheeting vide clause no. 801.3 as per
ASTM D 4956-09 specifications, fixed over 2
mm thick aluminium I 3 to 4 mm thick ACP
sheeting with Back support frame of 35x35x5 mm
mild steel angle with vertical and lateral clearance
given in clause 802.2 and 802.3, duly painted on
back side with two coats of grey stove enamel
paint and installed as per clause 802.6 over a
designed support system of structural steel work
trestles and trusses of sections and type as per
structural design requirements and approved
plans including painting with one coat of epoxy
primer and two coats of epoxy finish paint. The nut
bolts of board with angle iron post/supporting
structure after fixing at site has to be electrically
welded. Retro-retlective sheeting should be
with sev'ln years written warranty from the
manufacturer & authorised distributor
/convertor, for satisfactory field performance,
durability & stipulated retro-reflectance of retro·
reflective sheeting.This certificate in original
should be submitted to the Engineer in charge
by the contractor/supplier.
210
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
12 Supplying rolled steel channel post of 100 x .50 Rmt. 790.00 187.00
mm (ISMC) drilled on top and painted with one
coat of epoxy primer and two coats of epoxy finish
paint having black and white bands of 25 em last
part of the post 0.75 m below ground level is
painted with three coats of red lead paint with 2
nos. of high tensile G.l. bolt and nut of size 10 mm
Dia. of 25 mm long including transportation etc.
complete.
Spec. No. :As per IRC-67, & M.O.R.T. & H.
Circular No. RW/NH-33023/31/88 D.O. Ill Dated 2-
5-1994
211
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
13 Supplying M.S. Angle iron post of size 65 mm x Rmt. 501 .00 152.00
65 mm x 6 mm drilled on top and painted with one
coat of epoxy primer and two coats of epoxy finish
paint having black and white bands of 25 em, last
part of the post 0."15 m below ground level is
painted with three coats of red lead paint with 2
nos. of high tensile G. I. bolt and nut of size 10 mm
dia. of 25 mm long including transportation etc.
complete.
Spec. No. :As per IRC-67, & M.O.R.T. & H.
Circular No. RW/NH-33023/31/88 0.0.111 Dated 2-
5-1994
16 Supplying M.S. Angle iron frame for informatory Rmt. 185.00 95.00
sign boards of size 35 mm x 35 mm x 3 mm
welded and painted with one coat of epoxy primer
and two coats epoxy finish paint etc. complete.
212
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
17 Supplymg M.S. Angle 1ron frame for informatory Rmt. 175.00 92.00
sign boards of size 35 mm x 35 mm x 3 mm
welded and painted with one coat of staving
primer and two coats stove enamel paint etc.
complete.
Spec. No. :As per IRC-67, & M.O.R.T. & H.
Circular No. RW/NH-33023/31/88 0 .0.111 Dated 2-
5-1994
213
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
22 Painting and numbering trees with white back No. 20.00 15.00
ground and black lettering etc complete. (23 x
23cm)
Spec. No. :As directed by Engineer-in-charge.
214
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
23 Painting with approved enamel paint in two coats No. 83.00 41.00
including cleaning surface and lettering for
CAUTIONARY I MANDATORY SIGN BOARDS
etc complete.
Spec. No. :M.O.R.T. & H. 2013 Cl.
1906.P.No.614.
24 Painting INFORMATORY SIGN BOARDS/ No. 155.00 62.00
VILLAGE NAME BOARDS with approved enamel
paint in two coats and lettering including cleaning
surfac~ etc. complete.
Spec. No. :M.O.R.T. & H. 2013. Cl.
1906.P.No.614.
25 Painting Nallah flow direction, span no. and No. 21.00 10.00
location on masonry work with approved enamel
paint in two coats including background painting
and lettering including cleaning surface etc.
complete.
Spec. No. :M.O.R.T. & H. 2013 Cl.
1906.P.No.614.
26 Painting 5th K.M. stone with approved enamel No. 111.00 85.00
paint in two coats complete and lettering including
cleaning surface etc.complete.
Spec. No. :M.O.R.T. & H. 2013 Cl.
1906.P.No.614.
215
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed I Labour
216
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed J Labour
217
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs,)
CODE
NO. Completed I Labour
•
40 Providing and erecting "Thrie" metal ileam Rmt 4768.00 323.00
crash · barrier comprising of 3 mm thick
corrugated sheet metal beam rail, 85 em above
road/ground level, fixed on ISMC channel vertical
post of size 150 x 75 x 5 mm spaced 2 m centre to
centre, 2.00 m in height and 1.15 m below ground
level, all steel parts and fitments to be galvanised
by hot dip process, all fittings to conform to
IS: 1367 and IS: 1364, metal beam rail to be fixed
on the vertical post with a space of channel
section 150 x 75 x 5 mm, 546 mm long complete
as per M.O.R.T.& H. clause 810 etc. complete.
218
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO. Completed .I Labour
41 Provision of an Reinforced cement concrete
crash barrier at the edges of the road ,
approaches to bridge structures and medians,
constructed with required grade concrete with
HYSD reinforcement conforming to IRC:21 and
dowel bars 25 mm dia, 450 mm long at expansion
joints filled with pre-moulded asphalt filler board,
keyed to the structure on which it is built and
installed as per design given in the enclosure to
MOST circular No. RW/NH - 33022/1/94-DO Ill
dated 24 June 1994 as per dimensions in the
approved drawing and at locations directed by the
Engineer, all as specified etc. complete.
42 Flexible Crash Barrier, Wire Rope Safety Barrier Rmt. 2155.00 86.00
(Providing and erecting a wire rope safety barrier
with vertical posts of medium weight RS Joist
(ISMS series) 100 mm x 75 mm (11.50 Kg/m),
1.50 m long 0.85 m above ground and 0.65 m
below ground level, split at the bottom for better
grip, embedded in M-15 grade cement concrete
450 x 450 x 450 mm, 1.50 m center to center and
with 4 horizontal steel wire rope 40 mm dia and
anchored at terminal posts 15 m apart. Terminal
post to be embedded in M-15 grade cement
concrete foundation 2400 x 450 x 900 mm (depth)
strengthened by a strut of RS Joist 100 x 75 mm,
2 m long at 450 inclination and a tie 1OOx 8 mm,
1.50 m long at the bottom, all embedded in
foundation concrete as per approved design and
drawing, rate excluding excavation and cement
cocrete.)
Spec. No. :M.O.R.T.& H. 2013 Cl. 811.P.No.360.
219
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
. . . .
Completed I Labour
220
SURVEY .
WORKs ·
6. SURVEY WORKS 1
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
211
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
222
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
223
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
225
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
227
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
228
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
COOl!
NO.
Completed Labour
25 Preparing and providing contour survey map Sq. Km. 27766.00 12483.00
of river I stream on UIS and DIS. of
proposed bridge site including chain and
compass survey and ·taking levels survey at
,every (15M x 15M) Preparing contour map
and supplying ammonia prints in 5 sets etc.
complete.
If Survey work is carried out by
departmental technical staff, (labour rate
only)
As directed by Engineer in charge.
[As per "Guidelines ,for preparation of Road
Project" by P.W.D.]
229
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
230
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
29 Providing and carrying out "Traffic Census" Per Day 9371 .00
for 7 days on N.H. I S.H. I M.D.R. by
employing a team . of skilled person for
counting each type of vehicle running on the
highways, recording their numbers as per
method suggested by Engineer-in -charge,
calculating traffic intensityiP.C.U. including
labour, materials stationery and rental charges
of tables, chairs, red flags, etc. complete and
giving final report of traffic.
As directed by Engineer in charge.
[As per IRC Guideline]
For Count post having traffic intensity
more than 20,000 M.T./Day
j) Trial plot on fit to scale of taluka map making No. 121 .00
corrections on white paper.
232
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
233
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
234
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
235
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
236
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
237
SR. NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
'
& (In Rs.)
CODE
NO.
Completed Labour
238
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
VIDEO PHOTOGRAPHY
1 Preparing and carrying out coloured video
shooting of road, bridges, other structures
and programmed, including preliminaries
survey, still shots, moving shooting, necessary
board for coloured video shooting, hiring of
vehicle, equipments for video shooting,
transportation of all equipments, persons
required for shooting, lighting arrangement as
may be necessary, editing, mixing, titling,
lettering, sounding including cost of Compact
Disc of approved quality etc.' complete.
239
SR.NO. DESCRIPTION OF ITEMS UNIT RATES FOR 2015-16
& (In Rs.)
CODE
NO.
Completed Labour
90.00
i) 4"x6" Size (3 copy) Each Set
145.00
ii) 5"x 7" Size (3 copy) Each Set
iii) Extra copies- 4"x6"Size Each 12.00
iv) Extra copies- 5"x7"Size Each 20 .00
240
MATERIAL,
LABOUR &
TRANSPORTATION
. RATES
MATERIAL RATES
Sr. Code Rate for
No.
Description Unit ' 2015-16(Rs.)
1 1 TRAP HEADER (17X22X60 TO 75 CM) APP . 60 CM LONG No. 36.00
2 2 TRAP HEADER APP. 75 CM LONG No. 40.00
3 3 RUBBLE STONE (BLASTED) Cu.m. 299.00
4 4 SAND (SCREENED) Cu.m. 732.00
5 5 CEMENT Bags 250.00
6 7 M. S. BARS OF V/S SIZES M. T. 42875.00
6 8 BINDING WIRES Kg. 75.00
7 9 NAILS Kg. 75.00
8 10a TMT STEEL M.T. 45410.00
9 15 RUBBLE AT QUARRY (MASONRY) Cu.m. 276.00
9 18 GRAVEL AT NALLA BED Cu.m. 200.00
10 19 FIRE WOOD Quintal 355.00
11 20 BITUMEN BULK VG 40 (30/40) AT MUMBAI M. T. 44872.00
12 20a BITUMEN PACK TIN VG 40 (30/40) AT MUMBAI M. T. 48848.00
12 21 BITUMEN BULK VG30 ( 60/70) AT MUMBAI M. T. 43256.00
13 21a BITUMEN PACK TIN VG30 ( 60/70)AT MUMBAI M. T. 47232.00
14 21b BITUMEN BULK VG10 (80/100) AT MUMBAI M. T. 42230.00
15 22 SOLVANT (LDO) Ltr. 49.43
15 30 PIN HEADER ( STD. SIZE) (Stone) No. 49.00
16 31 QUARRY SPALLS ( TRAP RUBBLE) Cu.m. 198.00
17 38 TRAP METAL 40 MM. (BLASTED) Cu.m. 388.00
18 39 TRAP METAL 40 MM. (HANDBROKEN) Cu.m. 408.00
18 40 TRAP METAL 40 MM. (CRUSHED) - Cu.m. 760.00
19 41 TRAP METAL 25 MM. (CRUSHED) Cu.m. 850.00
20 42 TRAP METAL 20 MM. (CRUSHED) Cu.m. 865.00
21 43 TRAP METAL 10 MM. I 12 MM (CRUSHED) Cu.m. 542.00
21 44 HARD MURUM Cu.m. 275.00
22 45 SOFT MURUM Cu.m. 246.00
23 46 TRAP METAL 6 MM. (CRUSHED) Cu.m. 552.00
24 905 Stone Dust , Cu. m. 282.00
24 49 BRICKS AGGREGATE ( 20 TO 40 MM) Cu.m. 346.00
25 53 STEEL FOR STRUCTURAL WORK M. T. 45670.00
26 54 STEEL PLATES M. T. 50584.00
27 55 SAND UNSCREEN FOR ROAD and BUILDING WORKS (Nallah Bed) Cu.m. 275.00
27 56 LIME SLAKED ( FINE LIME) Kg. 15.00
28 61 BRICK BATS Cu.m. 642.00
29 79 BRICKS ( II CLASS) No. 5.00
30 80a FLY ASH BRICKS No. 4.00
30 82 FIRE BRICKS No. 24.00
241
1-
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
31 92 CORNER STONES 38X20X30 CM. No. 76.00
32 95 ROUGH SHAHABAD (12-20 MM TH.) Sq. m. 199.00
33 97 WATER PROOFING COMPOUND Kg. 111.00
33 99 CHEQ. CEMENT TILES Sq. m. 227.00
34 103 KOTA STONE (MACHINE CUT) 25MM.TH Sq. m. 470.00
35 110 PLAIN CEMENT TILES Sq. m. 199.00
36 111 CEMENT COLOUR TILES Sq. m. 208.00
36 114 WHITE MAKRANA MARBLE SLAB (12mm TO 15mm) Sq. m. 1783.00
37 114a WHITE MARBLE (12mm TO 15mm) (Other than Makrana) Sq. m. 1352.00
Per 50 Kg.
38 117 WHITE CEMENT Bag
814.00
39 1"18 COLOURED CEMENT Kg. 114.00
39 119 MARBLE MOSAIC CHEQ. TILES(GREY) Sq . m. 273.00
40 122 KADAPPA ( MACH CUT) 25 MM TH. Sq. m. 408.00
41 127 KOTA STONE STEP (POLISHED) Sq. m. 513.00
42 131 CHEQUERED TILES (GRAY CEMENT) Sq. m. 190.00
42 138 LINSEED OIL DOUBLE BOILED Ltr. 114.00
43 139 TURPENTINE Ltr. 83.00
44 14 1 f=RENCH POLISH Ltr. 179.00
45 142 VARNISH Ltr. 161.00
45 143 COAL TAR Kg. 62.00
46 144 COMERCIAL SPIRIT Ltr. 62.00
47 145 WHITE ZINC PAINT Kg. 192.00
48 150 ALUMINIUM PAINT Ltr. 283.00
48 151 SYNTHETIC PAINT Ltr. 275.00
49 152 ENAMEL PAINT I FLAT PAINT Ltr. 275.00
50 154 RED OXIDE PAINT Kg. 161.00
51 155 PLASTIC EMULSION PAINT Kg. 305.00
51 158 COLOUR POWDER (YELLOW EARTH) Kg. 11.00
52 159 WASHABLE DISTEMPER Kg. 89.00
53 160 OIL BOUND DISTEMPER Kg. 106.00
54 163 WATER PROOF CEMENT PAINT Kg . 56.00
54 164 T. W. PLANKS 1.2 M. LENGTH Cu. m. 84458.00
55 175 T. W. PLANKS ABOVE 2.5 M. LENGTH Cu. m. 86§68.00
56 177 T.W. PLANK 25 TO 50 MM TH. 10-15 CM Wide Cu. m. 86235.00
57 178 T.W. GIRDER (JOIST) Cu. m. 86323.00
57 180 T.W. PLANKS 20 MM. TH (10-15 CM Wide) Cu. m. 82750.00
58 180a Teak Wood Battens Cu. m. 60867.00
59 183 T.W.BULLIES 100 MM DIA Rmt. 170.00
60 184 T.W. BULLIES 125 MM DIA. Rmt. 182.00
242
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
60 185 T.W. BULLIES 150 MM DIA. Rmt. 185.00
61 186 JUNGLE WOOD PLANKS & IN GENERAL Cu. m 33567.00
62 190 G.l. SCREW BOLTS No. 3.00
63 191 G.l. 'J' HOOKS 6 MM. DIA. No. 7.00
63 192 G.l. WASHERS No. 1.00
64 193 MANGLORE TILES CLASS "A" No. 12.00
65 196 J.W.BALLIES 150 MM. DIA Rmt. 79.00
66 197 MANGLORE RIDGE/HIP TILES No. 24.00
66 199 G.C.I. SHEETS (CORRUGATED) 20 BWG. M.T. 69893.00
67 199a G.I.SHEET COLOUR M. T. 72880.00
68 200 G.l. WASHERS Kg. 100.00
69 201 G.I. NUT AND BOLTS Kg. 103.00
69 206 STRONG IRON BOLTS 10 MM. DIA. Kg. 110.00
70 208 RIDGE CAP (PLAIN G.l.) M. T. 71280.00
71 210 BITUMINOUS WASHERS Kg. 110.00
72 211 A.C. SHEET RIDGE Pair. 298.00
72 211a Googly Bolt With Bitumenous Washer Kg. 88.00
73 213 MANGLORE GLASS TILE No. 384.00
74 223 HARD BOARD 6 MM. TH. Sq. m. 169.00
75 224 PLY WOOD 12 MM. TH. Commercial Sq. m. 435.00
75 225 PLY WOOD 6 MM. TH. Commercial Sq. m. 329.00
76 225a PLY WOOD 4 MM. TH. Commercial Sq. m. 209.00
77 226 PARTICAL BOARD (12 MM.TH.) Sq. m. 400.00
78 226a Marine Ply 12 mm Sq. m. 653.00
78 226b Marine Ply 6 mm Sq. m. 470.00
79 226c Marine Ply 4 mm Sq. m. 300.00
80 227 INDIAN SUPERIOR T. W. FRAME Cu.m 96700.00
81 228 IRON HOLD FAST 300X40X5MM No. 57.00
81 229 BUTT HINGES ALUMINIUM 75 MM No. 60.00
82 230 BUTT HINGES ALUMINIUM 100 MM No. 65.00
83 231 BUTT HINGES ALUMINIUM 125 MM No. 62.00
84 232 TOWER BOLT ALUMINIUM 150 MM No. 53.00
84 233 TOWER BOLT ALUMINIUM 200 MM No. 65.00
85 234 TOWER BOLT ALUMINIUM 250 MM No. 76.00
86 235 HANDLe ALUMINIUM 125 MM. No. 55.00
87 236 HANDLE AND EYES ALUMN. 225 MM No. 35.00
87 239 GLASS 5.5 MM. THICK (PLAIN) Sq. m. 548.00
88 241 HANDLE IRON OXI. 100 MM. No. 35.00
89 242 TOWER BOLT 150 MM. IRON No. 34.00
243
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
90 243 HOOK & EYE IRON OXI. 75 MM No. 20.00
90 245 HANDLE IRON OXI. 125 MM No. 39.00
91 246 HOOKS AND EYES 225 MM IRON OXI No. 24 .00
92 247 MORTICE LOCK SUPERIOR No. 808.00
93 248 SLIDING DOOR BOLT (TADI) No. 73.00
93 249 ALDROP ALUMINIUM 300 X 16 MM No. 199.00
94 250 . BUTT HINGES IRON OXI. 125 MM No . 40.00
95 251 BUTT HINGES IRON OXI.1 00 MM No. 34.00
96 252 BUTT HINGES IRON OXI. 90 MM No. 25.00
96 253 ALDROP IRON OXI. 300 MM (20 MM DIA.) No. 131 .00
97 254 IR. OXI. TOWER BOLT 150 MM. No. 72.00
98 255 TOWER BOLT IRON OXI. 250 MM. No. 88.00
99 256 TOWER BOLT IRON OXI.200 MM No. 77.00
99 257 LATCH 250 MM LONG IRON OXI. No. 50.00
100 258 BLACK HINGES No. 14.00
101 259 STR. BUTT HINGE BR.OXI 150 MM. No. 83.00
102 260 STR. STRAP HINGE BR.OXI200 MM. No. 94.00
102 261 STR. BUTT HINGE BR.OXI100 MM. No. 73.00
103 262 TOWER BOLT IRON OXI.300 MM No. 104.00
104 263 CHAIN AND STARLE IRON No. 40.00
105 264 BR.OXI, TOWER BOLT 250 MM. No. 203.00
105 265 IRON OXI. STRAP HINGE No. 34.00
106 266 B.R. ORNAMENTAL HANDLE No. 200.00
107 269 HANDLE FOR STEEL WINDOWS No. 37.00
108 272 SOLID CORE T.W. VENEER 35 MM Sq. m. 1496.00
108 273 BRASS DOUBLE ACTING SPRING HINGES No. 190.00
109 274 SOLID CORE (COMME)SHUTTER 35 MM Sq. m. 1222.00
110 276 X.P.M . 12 MM X 18 GAUGE Sq. m. 143.00
111 277 HANDLE IRON OXI.150 MM No. 45.00
111 278 STOPPER FOR STEEL WINDOW No. 40.00
112 279 FLY PROOF G.I. WIRE MESH Sq. m. 204.00
113 288 HAMP ROPE Kg. 87.00
114 292 FERRUL FOR C.l. PIPE 100 MM No. 152.00
114 293 COUPLING C.l.80 MM. No. 144.00
115 294 COUPLING CAST IRON 100 MM No. 133.00
116 296 BELL MOUTH COVER (1 00 MM) DIA No. 72.00
117 304 CLAMP FOR G.l. PIPE No. 10.00
117 319 BIB STOP TAP BR. HEAVY 15 MM. No. 200.00
118 320 BIB STOP TAP BR. HEAVY 20 MM. No. 311 .00
244
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
119 321 BIB STOP TAP BR. HEAVY 25 MM. No. 360.00
120 322 SOCKET FOR 15 MM. TAP No. 18.00
120 323 SOCKET FOR 20 MM. TAP No. 24.00
121 324 SOCKET FOR 25 MM. TAP No. 33.00
122 326 WHEEL STOP TAP OF BRASS 15 MM No. 248.00
123 327 WHEEL STOP TAP OF BRASS 20 MM No. 360.00
123 328 WHEEL STOP TAP OF BRASS 25 MM No. 526.00
124 331 GUN M. STOP TAP & CR. WH. 20 MM No. 242.00
125 332 GUN M. STOP TAP & CR.WH 25 MM No. 283.00
126 334 SHOWER ROSE CHR PLATED BR 10 CM No. 262.00
126 340 BALLCOCK 15 MM. DIA. P.V.C. FLOAT No. 196.00
127 341 BALLCOCK 25 MM. DIA. P.V.C. FLOAT No. 310.00
128 348 W.C. PANS 63 CM. Indian Closet WITH TRAP No. 638.00
129 350 FOOT REST CHEQUERED 25 X 10 CM Pair. 134.00
129 352 W.C. PAN 63 CM. 1ST CL(ORISA) No. 1020.00
130 353 W.C. PAN 63 CM (ORRISA TYPE) CM. 1ST CLASS WITH TRAP No. 1243.00
131 354 HALF STALL TYPE URINAL No. 1919.00
132 356 LIPPED TYPE URINAL No. 606.00
132 357 HALF ROUND E.W. PIPE 100 MM. Rmt. 50.00
133 358 WASH BASIN (45X30 CM COL. GLAZE) No. 766.00
134 359 W/GLAZED E.W.SINK 0.600.2X0.45 with ace. No. 1791.00
135 360 15 MM DIA CRO.PLATED BIB COCK No. 210.00
135 362 WHITE GLAZED W.H. BASIN 0.45XOX0.3X0.2 No. 665.00
136 366 A. C. RAIN WATER PIPE 75 MM. DIA Rmt. 74.00
137 367 BIB TAP 15 MM BRASS MEDIUM No. 149.00
138 369 C.l. COWLNENT 75 MM. DIA No. 269.00
138 370 C.l. COWLNENT 100 MM. DIA No. 297.00
139 371 C.l. COWLNENT 150 MM. DIA No. 387.00
140 372 C.I.COLLER 75 MM. DIA No. 225.00
141 373 C.I.COLLER 100 MM.DIA No. 246.00
141 374 C.I.COLLER 150 MM. DIA No. 323.00
142 375 G.I.PIPE 15 MM. DIA MEDIUM TYPE Rmt. 153.00
143 376 G. I. PIPE 20 MM. DIA MEDIUM Rmt. 178.00
144 377 G.I.PIPE 25 MM. DIA MEDIUM Rmt. 223.00
144 378 G.I.PIPE 32 MM. DIA MEDIUM Rmt. 273.00
145 379 G. I. PIPE 40 MM. DIA MEDIUM Rmt. 327.00
146 380 G. I. PIPE 50 MM. DIA MEDIUM Rmt. 442.00
147 381 G.I.PIPE 65 MM. DIA MEDIUM Rmt. 547.00
147 382 G.I.PIPE 80 MM. DIA MEDIUM Rmt. 687.00
245
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
148 383 G.I.PIPE 100 MM. DIA MEDIUM Rmt. 975.00
149 384 EUROPEAN TYPE W.C. PAN 68 C.M. (WHITE) No. 1365.00
150 393 C.I.GRATING 75 MM. DIA No. 51.00
150 394 C.I.GRATING 100 MM. DIA No. 56.00
151 395 A.C. PIPE 100 MM. DIA Rmt. 68.00
152 396 A.C. PIPE 75 MM.DIA. SHOE No. 58.00
153 397 SALT GLAZED S.W. GULLY TRAP No. 141.00
153 398 STONE WARE PIPE 100 MM. DIA Rmt. 99.00
154 407 U.P.V.C.PIPE 15 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 56.00
155 408 U.P.V.C.PIPE 20 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 66.00
156 409 U.P.V.C.PIPE 25 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 76.00
156 410 U.P.V.C.PIPE 32 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 98.00
157 411 U.P.V.C.PIPE 40 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 122.00
158 412 U.P.V.C.PIPE 50 MM. DIA.1 OkGF/Cm2 PRESSURE Rmt. 137.00
159 413 U.P.V.C.PIPE 60 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 167.00
159 413B U.P.V.C.PIPE 75 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 243.00
160 413C U.P.V.C.PIPE 90 MM. DIA.10kGF/Cm2 PRESSURE Rmt. 303.00
161 414 COLOUR EUROPEAN TYPt= W.C. PAN No. 1402.00
162 415 COLOUR WASH H.BASIN 45 CM X 30 CM No. 916.00
162 420 GUN. M. STOP COCKS 15 MM CL. WHEEL No. 193.00
163 422 BRASS WHEEL STOP TAP 32 MM. DIA No. 474.00
164 424 BRASS WHEEL STOP TAP40 MM. DIA No. 569.00
165 426 BRASS WHEEL STOP TAP 50 MM. DIA No. 1256.00
165 428 BRASS WHEEL STOP TAP 65 MM. DIA No. 1493.00
166 430 BRASS WHEEL STOP TAP 80 MM. DIA No. 2729.00
167 432 GUN METAL STOPCOCK C. WHEEL 20 MM No. 416.00
168 433 GUN METAL STOPCOCK C. WHEEL 25 MM No. 560.00
168 434 GUN METAL STOPCOCK C. WHEEL 32 MM No. 685.00
169 442 WH. GL. FULL STALL URINAL No. 3660.00
170 446 WH. GL. WASH BASIN 63 X 45 CM. No. 978.00
171 447 COL. GL. WASH BASIN 63 X 45 CM. No. 1406.00
171 456 C.I.Y. JUNCTION 75 MM DIA No. 296.00
172 457 C.I.Y. JUNCTION 100 MM DIA No. 367.00
173 45 8 C.I.Y. JUNCTION 150 MM DIA No. 459.00
174 459 A. C. COLLER No. 33.00
174 460 C.l. PLUG BENT 150 MM DIA No. 1035.00
175 461 A.C. DOUBLE 'Y' JUNCTION 100 MM No. 95.00
176 462 A.C. DOUBLE 'Y' JUNCTION 150 MM No. 128.00
177 463 A. C. DOUBLE 'Y' JUNCTION 75 MM No. 86.00
246
Sr. Code Rate for
Description Unit
No. 2015-1 6(Rs.)
177 464 A.C. PIPE 150 MM DIA. Rmt. 90.00
178 465 A. C. PLUG BEND 150 MM DIA. No. 95.00
179 466 STONE WARE PIPE 150 MM DIA. Rmt. 163.00
180 467 STONE WARE PIPE 225 MM DIA. Rmt. 209.00
180 591 COL. GLAZED TILES 15 X 15 CM. Doz. 181 .00
181 597 ALLUMINIUM ROD 25 MM DIA. Rmt. 57.00
182 598 VENEER 4 MM THICK T.W. Sq. m. 445.00
183 602 WIRED GLASS 6 MM THICK Sq. m. 631 .00
183 603 C. I. PIPE 75-80 MM. DIA. Rmt. 699.00
184 604 C. I. PIPE 100 MM DIA. Rmt. 848.00
185 605 C. I. PIPE 150 MM DIA. Rmt. 1305.00
186 ~ ?2 GULLY TRAP COVER WITH FRAME C.I. No. 203.00
186 626 A. C. SHOE 100 MM. DIA No. 72.00
187 628 A. C. COWL. VENT. ( 100 MM DIA.) No. 63.00
188 630 A. C. BEND 75 MM No. 59.00
189 631 A. C. BEND 100 MM No. 62.00
189 632 C. I. BEND 100 MM No. 342.00
190 635 TOWEL ROD WITH CLAMPS ( 16MM DIA) Cromium Plated 60 CM No. 178.00
191 641 HINGES 125 MM Cromium Plated No. 62.00
192 642 TOWER BOLTS 300 MM CR. PLATED (IRON) No. 77.00
192 643 TOWER SOLTS 200 MM. CR. PLATED (IRON) No. 63.00
193 644 ALDROP 300 X 16 MM CR. PLATED No. 173.00
194 645 HANDLE 125 MM CR. PLATED No. 62.00
195 647 HOOKS AND EYES CR. PLATED No. 35.00
195 648 BR. OXI. BUTT. HINGES 125 MM No. 91.00
196 649 BR. OXI. ALDROP 300 X 16 MM. No. 409.00
197 650 BR. OXI. HANDLES 125 MM No. 122.00
198 651 BR. OXIDE TOWER SOLTS 300 MM No. 257.00
198 652 BR. OXI. TOWER SOLTS 200 MM No. 192.00
199 653 BR. OXI. HOOKS AND EYES 200 MM No. 74.00
200 655 BR. OXI. HINGES 100 MM. No. 83.00
201 656 HINGES IRON 100 MM No. 35.00
' 201 659 WELDED MESH 50 X 50 X2.54 MM (10 GAUGE) Sq. m. 331.00
202 663 BARBED WIRE Kg. 78.00
203 664 BAMBOO 50 MM DIA. Rmt. 35.00
204 665 COIR STRING Kg. 56.00
204 666 BAMBOO 25 MM OIA. Rmt. 24.00
205 708 RED POWDER I GERU Kg. 15.00
206 719 NON TEAK I JUNGLE WOOD Cu. m. 30883.00
247
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
207 721 CHICKEN PROOF JALI Sq. m. 45.00
207 755 CEMENT BASE PUTTY Kg. 56.00
208 801 T. W . PARTICLE BOARD, BOTH FACE LAMINATED 12MM Sq. M. 742.00
209 837 A. C. COWL. DOME 3" (75 MM) DIA. No. 4 1.00 I
210 838 A. C. COWL. DOME 4" (1 00 MM) DIA. No. 52.00
210 SYMET BATH FITTINGS.
211 839 WASTE COUPLING 31/32 MM (HIT/FIT) No. 78.00
212 840 GRATING DOOM 100 MM No. 46 .00 I
213 841 GRATING DOOM 125 MM No. 4l. OO !
213 842 GRATING DOOM WASTE HOLE 125 MM No. 45.00 I
214 843 GRATING ROUND 140 MM No.
I
66.00 I
215 844 GRATING SQUARE 150 MM No. 126.00
216 845 GRATING SQUARE WASTE HOLE 150 MM No. 126.00 I
216 846 GRATING SQUARE FITTINGS 100 MM No. 105.00 II
217 848 BIBCOCK STANDARD 15 MM. No. 155.00 \
248
Sr. Code Rate for
Description Unit 2015-16(Rs.)
No.
236 873 TOWER BOLT (4 ") 100 MM No. 46.00
237 874 TOWER BOLT (6 ") 150 MM No. 58.00
237 875 TOWER BOLT (8 ") 200 MM No. 70.00
238 876 UPVC SANITORY GRADE PIPE 75 MM Rmt. 166.00
239 877 UPVC SANITORY GRADE PIPE 110 MM Rmt. 247.00
240 878 UPVC SANITORY GRADE PIPE 160 MM Rmt. 380.00
240 CAST IRON SPIFGOT SOCKET PIPE I.S. 1536 I 1989 'CLASS LA
241 879 80 MM DIA. Rmt. 762.00
242 880 100 MM DIA. Rmt. 962.00
243 881 125 MM DIA. Rmt. 1239.00
243 882 150 MM DIA. Rmt. 1491 .00
244 883 200 MM DIA. Rmt. 2420.00
245 884 250 MM DIA. Rmt. 2620.00
246 oo5 ::SOO MM DIA. Rmt. 3557.00
....;:c'· ··--·
246 886 CERAMIC TILES 300MM x 300MM Sqm 514.00
STAINLESS STEEL SINK 600MM X 450MM X 250MM (1 mm Thick)
247 887 No. 2123.00
WITHACCE.
248 888 PVC FLUSHING TANK 10 LIT. CAPACITY WITH ACCE. No. 712.00
249 889 L.D.O Litre 49.43
250 890 DOUBLE CHARGED VETRIF!ED TILES 600 MM x 600MM, 8 MM Sq.m 990.00
DOUBLE CHARGED VET RIFlED TILES 1000 MM x 1000 MM, 'I 0 MM
251 891 Sq.m 1227.00
THICK.
252 892 GYPSUM BOURD 9 MM THICK Sq.rn 340.00
253 892a GYPSUM BOURD 12.5 MM THICK Sq.m 347.00
254 893 P.O.P. GELLING SHEET 12.5 MM THICK Sq.m '176. 00
255 895 SUPER PLASTICIZER Litre 113.00
256 896 iRON OXIDISED PARLIAMENTRY HINGES SIZE 75 MM x 150 MM No. 52.00
257 897 IRON OXIDISED PARLIAMENTRY HINGES SIZE 100 MM x 150 MM No. 52.00
258 898 IRON OXIDISED PARLIAMENTRY HINGES .:J1ZE 125 MM x 150 MM No. 62.00
259 899 BRASS OXIDISED PARL!AMENTRY HINGES SIZE 75 MM x150 MM No, 331.00
260 900 BRASS OXIDISED PARLIAMENTRY HINGES SIZE 100 MM x 150 No. 351 .00
261 901 BRASS OXIDISED PARLIAMENTRY HINGES SIZE 125 MM x 15G No. 387.00
262 902 GLASS 3.0 MM THICK(PLA.I N) Sq.m. 347.00
263 902a GLASS 4.0 MM. THICK ( PLAIN l Sq.m.
264 902b GLASS 5.0 MM. THICK ( PLAIN ) Sq.m. 464.00
265 902c GLASS 6.0 MM. THICK (PLAIN) Sq.m. 537.00
266 902d GLASS 8.0 MM. THICK ( PLAIN) Sq.m. 837.00
267 902e GLASS 10.0 f\IIM. THICK (PLAIN) Sq.m. 1019.00
268 903 GLASS 3.0 MM. THICK( BAJR!) Sq.m. 265.00
269 904 EMULSION WATER BASED (WATER PROOF CEMENT PAINT) Litre 180.00
270 906 FLY ASH M.T. 45.00
271 907 ANGLO INDIAN TYPE W.C.Pl\N NO. 1712.00
272 908 -
WATER JET WITH.'
PIPE FOR W.C.
' .
S.S. NO. 558.00
273 909 BIB COCK SWAN NECK LONG HEADED FOAM FLOW NO. 703.00
274 910 SUNMICA 0.8MM Sq.m 154.00
275 911 FOURMICA 1MM Sq.m 405.00
276 912 ADDESIVE (FEVICAL) KG 152.00
277 913 BAISON BOARD 8 MM Sq.m 306.00
278 913a BAISON BOARD 12 MM Sq.m 437.00
Sr. Code Rate for
Description Unit 2015-16(Rs.)
No.
279 914 GRADE-l CRUSHED METAL (90 MM TO 45 MM) Cu. m. 624.00
280 915 GRADE-II CRUSHED METAL (63 MM TO 45 MM) Cu. m. 696.00
281 916 GRADE-Ill CRUSHED METAL (53 MM TO 22.4 MM) Cu . m. 665.00
282 STEEL FIBRE (M.S.CRIMPED FLAT) Kg. 71 .00
283 50 FUSE No 163.00
284 47 BLASTING POWDER KQ 69.00
285 573 WELDING ELECTRODE No 3.00
186 669 OXI ACETYLENE GAS Cylinder 3442.00
287 162 ZINK BASED OIL PAINT Liter 334.00
288 672 STEEL PIPE FOR ROOF 50 MM DIA. Rmt 171.00
289 673 STEEL PIPE FOR ROOF 40 MM DIA. Rmt 138.00
290 674 STEEL PIPE FOR ROOF 25 MM DIA. Rmt 116.00
291 54 GUSSET PLATE Kg. 77.00
292 291 NUT & BOLT 16 MM DIA. Kg 138.00
293 -- PLYWOOD CENTERING 15 MM THICK Sq.m 690.00
294 -- STEEL PROPS (12' HEIGHT) No 1730.00
295 -- FAN HOOK BOX No 224.00
296 -- MELAMINE BASED ADMIXTURE PLASTICIZER Liter 123.00
297 -- R.C.C. JALI 50 MM THICK Sq.m 375.00
298 -- R.C.C. JALI 80 MM THICK Sq.m 418.00
299 -- HALLOW BLOCK No 77.00
300 -- POLYMERIC MEMBRANE & PRIMER Kg 397.00
301 4 POLYMER Kg 382.00
302 -- GLASS I FIBER MESH Sq.m 36.00
303 -- POLYPROPYLENE FIBER Kg 490.00
304 -- INTEGRAL WATER PROOFING COMPOUND Liter ?.48.00
305 -- NON SHRINK GROUT Kg 330.00
306 -- NOZZLES FOR GROUTING each 37.00
307 -- TEXTURED PAINT (MIX PUTTY) Liter 1563.00
308 -- WATER REPELLANT (PERMA MAKE OR EQUIVALLENT) Liter 433.00
309 721 FIBER MESH ALKALI RESISTANCE Sq.m 35.00
310 -- NAIL WI RES ETC. Kg 111.00
311 -- SYNTHETIC TILES Sq.m 446.00
312 -- ADHESIVE (ROYAL MAKE) 20 KG Bag 698.00
313 -- PIGMENT FOR TILES Kg 86.00
314 114 WHITE MAKARANA MARBLES 20 MM THICK 115 MM THICK Sq.m 3192.00
315 131 COLOUR CHEQURED CEMENT TILES Sq.m 163.00
316 -- COW DUNG Bag 42.00
317 -- POLISHING STONE No 113.00
318 -- BITUMINOUS PAD 25 MM THICK I A.C.POLYSEAL Sq.m 353.00
319 202 G.l. SCREW 50 MM Gross 58.00
320 133 ALLUMINIUM STRIP Kg 303.00
321 575 BITUMEN JOIN FILLER I A.C.POLYSEAL Kg 194.00
322 -- LEAD PIPE I PLATE Kg 280.00
323 HOLLOW CLAY BRICKS 4" No 73.00
324 HOLLOW CLAY BRICKS 6" No 95.00
- 325 HOLLOW CLAY BRICKS 8" No 107.00
326 CPVC PIPE- SDR 13.5
327 i) 15MM Rmt 33.00
328 ii) 20MM Rmt 48.00
329 iii) 25MM Rmt 65.00
330 iv) 32MM Rmt 99.00
331 v) 40MM Rmt 115.00
332 vi} 50MM Rmt 165.00
333 vii) 65MM Rmt 180.00
250
Sr. Code Rate for
Description Unit
No. 2015-16(Rs.)
334 viii) 80MM Rmt 220.00
335 PRESMATIC AUTO CLOSING CONCEALED URINAL FLUSH VALVE NO 1910.00
336 METROPOLE FLUSH VALVE NO 2880.00
THERMOPL.A.STIC ROAD MARKING MATERIAL IN WHITE I
337 Kg 83.00
YELLOW COLORED
338 GLASS BEADS Kg 85.00
339 REFLECTIVE PAINTS Litre 863.00
340 PAVEMENT MARKER STUD (CAT EYE) No 165.00
341 PVC SOLID FLUSH DOOR Sq.m 2660.00
342 PAVING BLOCK
343 i) 60MM TH M 40 Sq.m 461 .00
344 ii) 80MM TH M 40 Sq.m 574.00
345 ITALIAN GLASS MOSAIC TILES Sq.m 1949.00
346 TREMIX MACHINE ON RENT Sq.m 65.00
347 ii) CC GROOVE CUTTING Rmt 40.00
348 iii) FILLING BITUMEN IN GROOVE Rmt 15.00
349 iv) FILLiNG POLY SULFIED IN GROOVE Rmt 25.00
350 PROFLEX SHEETING SHED
351 i) 15M SPAN x 21M LENGTH Sq.m 1960.00 .
352 ii) 18M SP.A.N x 38.15M LENGTH Sq.m 2283.00
353 iii) 21.3M SPAN x 42M LENGTH Sq.m 2509.00
354 iv) 28.05M SPAN x 54M LENGTH Sq.m 2882.00
355 GRANITE SUPER QUALITY Sq.m 2704.00
356 FIBER R/F HEAVY DUTY CEMENT CONCRETE TILES FOR
357 i) FLOOR Sq.m 625.00
358 ii) STEP Sq.m 670.00
359 .A.AC BLOCK Sq.m 3880.00
360 AAC BLOCK 600 X 200 X 100 No 47.00
361 ALLUMINIUM SHEETING FIXED WITH ENCAPSULATED LENS Sq.m 6300.00
362 BEARING (PTFE) No 13220.00
DELINATOR FROM lSI CERTIFIED FIRM AS PER THE STANDERED
363 No 750.00
DRAWING GIVEN IN IRC:79
364 SHANK CAT EYE No 225.00
365 POLYASSYTAL MATERIAL (UPVC) 15 MM
366 a) BIBCOCK STANDERED No 60.00
367 b) BIBCOCK FANCY No 62.00
368 c) BIBCOCK LONG BODY No 80.00
369 d) BIBCOCK PILLER COCK No 250.00
370 e) STOP COCK 15 MM WITH HANDLE BELL No 135.00
371 f) ANGLESTOPCOCK15MM No 150.00
372 g) CONCEAL STOP COCK 15 MM OF UPVC No 220.00
373 h) CONCEAL STOP COCK 20 MM OF UPVC No 224.00
374 i) STOP COCK 20 MM (FEMALE) No 178.00
375 BITUMEN PAD 25 MM THICK 1.20 M X 1.20 M Each 1388.00
376 RECTROREFLECTIVE TAPE Sq.m 0.70
377 EPOXY RESIN Kg 410.00
378 HARDNER Kg 826.00
379 G.l. WIRE MESH 3.7 M DIA WITH PVC COATING Sq.m 187.00
380 EDGE WIRE 4.40 MM DIA Kg 79.90
381 HIGH INTENSITY MICRO PRISMATIC GRADE (TYPE-IV) SHEET Sq.m 1739.00
382 2 MM THICK ALUMINIUM SHEET Sq.m 1960.00
383 3 MM TO 4 MM THICK ACP SHEET Sq.m 1440.00
251
8. LABOUR RATES
Sr. Code Description Unit Rate For2015-16
No. (Rs.)
252
RATES FOR TRANSPORTATION OF METAL FOR YEAR
2015- 2016 ( Including Service Tax )
LEAD IN K.M. RATES FOR 2015-2016
(Rs.)
0.5 85.00
1 93.00
1.5 101.00
2 110.00
2.5 118.00
3 127.00
3.5 135.00
4 143.00
4.5 151.00
5 159.00
5.5 167.00
6 176.00
6.5 183.00
7 192.00
7. 5 199.00
8 207.00
8.5 215.00
9 223.00
9.5 230.00
10 238.00
10.5 244.00
11 250.00
11.5 256.00
12 262.00
12.5 268.00
13 274.00
13.5 280.00
14 286.00
14.5 291.00
15 297.00
15.5 302.00
16 310.00
16.5 317.00
17 324.00
17.5 332.00
18 339.00
18.5 347.00
19 354.00
19.5 361.00
20 369.00
20.5 375.00
21 381 .00
21.5 387.00
22 393.00
253
I
LEAD IN K.M. RATES FOR 2015-2015
(Rs.)
22.5 399.00
23 405.00
23.5 411.00
24 417.00
24.5 423.00
25 428.00
25.5 434.00
26 440.00
26.5 446.00
27 451.00
27.5 457.00
28 463.00
28.5 468.00
29 474.00
29.5 480.00
30 485.00
NOTE:-
1. AFTER KM. 30 ADD FOR EACH Rs. 9.1 0 Per kmlcum
SUBSEQUENT KM FROM KM 3010 to
km. 6010
2. ADD FOR EACH SUBSEQUENT KM Rs. 7.20 Per krnlcum
FROM KM 60/0 TO KM. 10010
3. ADD FOR EACH SUBSEQUENT KM Rs. 6.55 Per kmlcum
FROM KM 10010 AND ABOVE
RATE FOR TRANSPORTATION OF R.C.C. PIPES AND COLLERS.
I] Lead upto 15 km. Rs. 22.25 per KM I MT
II] Lead from 15 km to 50 km. Rs. 15.65 per KM I MT
Ill] Beyond 50 km. Rs. 13.30 per KM I MT
Note :-Above Rate of transportation of p1pe and collers do not mclude loading and
unloading charges.
254
10. RATES FOR LOADING, UNLOADING, STACKING AND
TRANSPORTATION OF MATERIALS FOR THE YEAR 2015-2016
Sr. No. Materials Unit Rates for Rates for Rates for Rates for
Loading Unloading Stacking Transportation
carriage of including
materials carriage of
upto a lead materials
of 50 Mtrs. up to a
lead of 50
Mtrs.
(in Rs.) (in Rs.) (in Rs.)
1 Boulders Cu.M. 30.88 25.74 15.44 10% Extra over the rates
Rubbles & for Transportation of
Masonry stones metal
2 Metal of all Cu.M. 30.88 25.74 15.44 As per schedule
sizes attached
3 Moarum Sand Cu,.M. 25 .74 24.17 10.29 15% Below the rates for
Earth & Loose Transportation of metal
material
4 Lime Cu.M. 36.03 32.59 12.01 30% Below the rates for
Transportation of metal
5 Shahabad/ Sq.M. 1.56 1.56 1.40 1/5 of the the rates for
Sikosa Transportation of metal
6 Fuel Wood M.T. 29.17 25.74 6.86 1/2 of the rates for
(Babul) Transportation of metal
7 Cement M.T. 44 .76 32.59 20.59 10% Below the rates for
Transportation of metal
for delivery other than
factory and Railway
8 Mild Steel bars M.t. 55.06 44.76 27.45 10% Below the rates for
of all sizes. Transportation of metal
9 Timber Cu,M. 32.59 24.03 12.01 30% Below the rates for
Transportation of metal
10 Maxphalt Pack M.t. 52.69 47.66 22 .58
Tin
..
10-A Carting of bulk ---- ---- ----
Bitumen
A) From refinery
10-B Bituminous & M.T. ---- ---- ---- 10% Below the rates for
Metal mix (mix Transportation of metal
material)
transportation .
255
Sr. No. Materials Unit Rates for Rates for Rates for Rates for
Loading Unloading Stacking Transportation
carriage of including
materials carriage of
upto a lead materials
of 50 Mtrs. up to a
lead of 50
Mtrs.
(in Rs.) (in Rs.) (in Rs.)
11 Bricks Cu.M. 27.45 27.45 18.88 Same as per rates for
Transportation of metal
12 Manglore tiles 1000 30.88 27.45 23.24 10% Below the rates for
including Nos Transportation of metal
Ridgeing and
Hipping
13 Single Allahbad 1000 30.88 27.45 23.24 10% Below the rates for
tiles and country Nos Transportation of metal
tiles
14 Flooring Tiles 1000 30.88 27.45 23.24 20% Below the rates for
size 0.30m x Nos Transportation of metal
0.30 m
256
Machinery Hire Charges For Year 2015-2016
257
Sr. No. DESCRIPTION UNIT Rate for 2015-16
in Rs.
33 Bouzer heating( asphalt) M.T. 173.00
34 Self propelled paver finisher H.P. 40 & 43.5 Hour 1055.00
61 Batch mix type hot mix plant- 80-120 TPH Hour 8085.00
capacity with SCADA
62 Asphalt Drum mix plant with SCADA Hour 3836.00
258
Sr. No. DESCRIPTION UNIT Rate for 2015-16
in Rs.
67 Gas cutter Hour 217.00
69 Batch mix type Hotmix Plant - 80- 120 TPH Hour 8489.00
Capacity with SCADA
'·
259
CEMENT CONSUMPTION
260
PUBLIC WORKS REGION NAGPUR
Executive Engineer
Road project Division
Nag pur
I
·-
261