Properties Component A: Component B: PU-Red KG-303 Chemical base Polyurethane Cement Colour Red Grey Density Approx. 1,3 g/cm³ Approx. 1,8 g/cm³ (applied) (applied) Working time 15 minutes 30 minutes Application temperature +5ºC - +20 ºC Recommended Thickness 1 mm approx. 9 mm if 6 mm steel deck 12 mm if 8 mm steel deck Consumption (theoretical) 3,8 m²/mm approx. 48 m²/mm per set per set Consumption ( practical) 3,3 m²/mm approx. 45 m²/mm per set per set Curing time at +20ºC and 65% r.h. but depending on 6 – 8 hours 8-10 hours, thickness of applied layer, temperature and ventilation in working area Shelf life Min. one year in Min. 6 months in unopened packaging unopened packaging if stored dry at if stored dry temperature not below 0ºC and not exceeding 40ºC
Product Description Product Benefits Areas of Application
Sikafloor® Marine PK-90 is a - Good vibration damping In all internal areas as under layer multilayer system with extremely - Levelling and sound reducing for vinyl, rubber, carpets, tiles etc. good sound and vibration reducing properties. It can also be used in connection properties, consisting of - Can easily be used in slipway with SikaFloor Marine Litosilo A) SikaFloor® Marine PU-Red; a systems. two component solvent-free, Certificates/Approvals fire retarding polyurethane − Wheel-Mark damping compound. − United States Coast Guard B) SikaFloor® Marine KG-303, a − Major authorities and cement based constraining classification societies. layer This product is manufactured in accordance with ISO 9001 and ISO 14001 quality assurance systems ® 1/ 2 Cure mechanism Application B) SikaFloor® Marine KG-303 ® A) SikaFloor Marine PU red Is most easily performed with a Powder may not be exposed to cures in approx. 6-8 hours at Linotol trowel (steel board) moisture. +20ºC Binder may not be exposed to B) SikaFloor® Marine KG-303 Removal and cleaning of tools freezing temperatures, heat and cures in approx. 8 -10 hours at SikaFloor® Marine KG-303: can be direct sunlight. 20ºC and 65% relative removed with water before the The applied compound may not be humidity. compound has cured. Once cured, exposed to freezing temperatures, the material can only be removed draft and direct heat or sunlight. Method of Application mechanically. Hands and exposed Surface preparation skin should be washed with water. For further technical information The surface has to be clean, free Use a suitable skin protection please contact our technical from dust, grease, oil and other cream department. substances, which may impair the adhesion. For additional technical information Notice: It is recommended, that aluminium please contact our technical ”Any information or suggestions for use surfaces are grinded in order to department. concerning Sika’s products, which we either in writing or orally have given improve the adhesion between the Further information buyers or end-users of the product, product and aluminium. have been given in good faith based on Copies of the following publications are available on request: our own experiences and based of Mixing process approved praxis and the technological A) SikaFloor® Marine PU-Red - Material Safety Data Sheet and scientific knowledge on the time of One set consists of: - Technical Data Sheet giving such suggestions and PU-Red Base: information, which are given without 1 bucket of 4,2 kg: Packaging information any type of guarantees, and which do Hardener: 1 can of 0,7 kg not lead to any further responsibility The components are mixed in a SikaFloor® Marine PU-red from Sika Danmark A/S, besides what large bucket (the bucket containing Bucket Base 4,2 kg is stated in the sales agreement in SikaFloor Marine PU-Red base) Can Hardener 0,7 kg question. The buyer or end-user should Industry
themselves investigate or otherwise
using a power drill with the ® make sure that our products are appropriate blender accessories. SikaFloor Marine KG-303 suitable for the use in question and The base and the hardener Bag Powder 40 kg further make sure that the products are quantities are measured – one kept and used correct and in bucket of base must be used with Drum Binder 120 kg agreement with the published rules and one can of hardener. Bag Quartz 40 kg considering the actual conditions in The prepared compound must be order to avoid damages or less used within approx. 15 min. at Important satisfactory results. Any order is +20ºC. ® accepted and any deliverance is A) SikaFloor Marine PU-Red: effected according to the general terms Application The unmixed parts and the applied Use a 2 mm toothed paste of sales and delivery from Sika compound must not be exposed to Danmark A/S, which are considered spreader, to end up with a layer moisture and freezing tem- known and accepted, and which could thickness of 1 mm. SikaFloor peratures. be handed out when asked for. Our Marine PU-Red. If the base becomes too stiff at low catalogues are not up-dated temperatures, the material may be automatically. The present product data B) SikaFloor® Marine KG-303 conditioned to a higher tem- sheet is only for use in Denmark. One set consists of: perature before mixing. Values stated in the present product KG-303 powder: The prepared PU-Red compound data sheet should be seen as One bag of 40 kg must not be exposed to moisture recommended, unless stated KG-303 binder: 10 kg otherwise.” and a temperature, which is below Quartz (2-3 mm): +5ºC before the curing process is One bag of 40 kg completed. One bag of powder and one bag of quartz are mixed with 10 kg of Binder until a suitable homogeneous mixture is obtained. Mix the compound in an agitator mixer (with fixed vessel) or with a power drill with appropriate blender accessories. The mixing time should not exceed 5 minutes. The prepared SikaFloor® Marine KG-303 must be used within approx. 30 min. at 20ºC.