Professional Documents
Culture Documents
NONE
Consumable material
Nitrogen
Skydrol 500 B4
Exxon 2380
Oxygen
Parts
NONE
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
1 of 11
General Notes
This Work Card was issued to perform a General Visual Inspection of the aircraft for proper configuration and
acceptable conditions. Perform every 24 hrs. or each crew change, whichever comes first.
General Visual Inspection (GVI) - A visual examination that will detect obvious unsatisfactory
conditions/discrepancies. This type of inspection may require removal of fillets, fairings, access panels/doors, etc.
Work stands ladders, etc. may be required to gain proximity.
Step by Step Work Instructions
STEPS Mechanic Inspector
STEP 1 : COCKPIT PREPARATION
NOTE: Enter your initials after performing each operation.
- Pressurize hydraulic system (Ref. DC10-AMM 29-00-00).____
- Extend flaps and slats. Tag appropriate controls and circuit
breakers.____
STEP 2: EXTERIOR INSPECTION
NOTE: Enter your initials after performing each operation.
E. Check that air conditioning packs 1 and 2 doors are closed and
secured.____
F. Check that air conditioning pack 1 and 2 exhaust area is
clear.____
G. Inspect left fuselage landing light for correct alignment and
general condition.____
H. Check that air conditioning pack 1 and 2 inlet area is clear.____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
2 of 11
A. Inspect nose landing and taxi lights for correct alignment and
general condition.____
C. Check nose gear safety pin and steering bypass valve pin are
removed.____
D. General condition of the gear and tires. Inspect for cuts, FOD
and correct inflation (Table 1).____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
4 of 11
5. RIGHT WING
A. Check access doors, wing tip and lights for security and general
condition.____
B. Check access panels for missing fasteners and general
condition.____
C. Check ailerons, flaps, spoilers and slats for damage and general
condition.____
D. Check for damaged or missing static discharges.____
E. Check gear down indicator for the correct position.____
F. Fuel level sticks and fuel panels are flush and fastened.____
G. Check fuel vent and fuel dump pipe for no fuel leakage.____
6. RIGHT, LEFT AND CENTER MAIN LANDING GEARS
A. Check general condition of gear and tires. Inspect for cuts, FOD
and correct inflation (Table 1).____
B. Inspect brake lines and wear indicator pins.____
C. Observe strut extension is per chart placard. CLG piston press
1000psi.____
D. Verify that gear safety pins are removed.____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
5 of 11
APU
NOTE: Perform the following items with APU turned off. Use
the necessary equipment to get access to the APU
Compartment.
A. Oil supply; check and replenish as necessary with lubricating
oil.____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
6 of 11
9. EMPENNAGE
A. From ground level check for indications of damage, fluid leaks
and general condition.____
B. Access doors and panels are closed and fastened.____
C. Check horizontal and vertical stabilizers, rudder and elevators for
damage and general condition.____
D. Check for damaged or missing static dischargers.____
E. Check the tail cone for security and general condition.____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
7 of 11
C. Check ailerons, flaps, spoilers and slats for damage and general
condition.____
F. Fuel level sticks and fuel panels are flush and fastened.____
G. Check fuel vent and fuel dump pipe for no fuel leakage.____
A. Check all tires for correct inflation and condition. Record in ITV
(DM-CP-003) for any correction made. CDP tire wear limit is
1/16” at the groove; notify CP Maintenance for DMI deferral to
replace tire prior to being smooth.____
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
8 of 11
K. Verify that gear pins are removed prior to departure and stored in
upper closet at L1 door. Make log page entry for Pre-Flight
completed.____
NOTE: (Before push back) Check that access doors L1 & R1,
fwd, center & aft lower cargo compartment doors
and main cargo door are closed and secured (view
pin on sight).
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
10 of 11
Tables
TABLE 1
TABLE 2
NOTE: Crew oxygen pressure: minimum dispatch pressure 1450 PSI at 21.2°C (70°F).
Service oxygen to 1850 PSI if pressure is below 1650 PSI. Make ITV entry as
required.
FORM ING-002
CIELOS DEL PERU S.A. WORK CARD
W/C N° Rev N° Date A/C N° or ESN Pages
August 7,
1-W/C-MP-10LM-007 1
2006
11 of 11
Figure 1
FORM ING-002