Professional Documents
Culture Documents
TECHNICAL MANUAL
ORGANIZATIONAL MAINTENANCE
REPAIR PARTS AND SPECIAL TOOLS LIST
FOR
MARCH 1987
HEADQUARTERS, DEPARTMENT OF THE ARMY
TM 9-1015-234-20P
CHANGE HEADQUARTERS
DEPARTMENT OF THE ARMY
No. 1 WASHINGTON, DC 17 December 1993
2. New or changed material is indicated by vertical bar in the margin of the page.
3. New or changed illustrations are indicated by a pointing hand highlighting the change.
File this sheet in the back of the manual for reference purposes.
TM 9-1015-234-20P
GORDON R. SULLIVAN
General, United Stales Army
Chief of Staff
Official:
MILTON H. HAMILTON
Administrative Assistant to the
Secretary of the Army
05634
DISTRIBUTION:
To be distributed in accordance with DA Form 12-40-E, block 0642 requirements for TM 9-1015-234-20P.
TM 9-1015-234-20P
You can help improve this manual. If you find any mistakes or if you know of a way to
improve the procedures, please let us know. Mall your letter, DA Form 2028
(Recommended Changes to Publications and Blank Forms), or DA Form 2028-2 located
in the back of this manual direct to: Commander, US Army Armament, Munitions and
Chemical Command, ATTN: AMSMC-MAS, Rock Island, IL 61299-6000. A reply will be
furnished to you.
DESTRUCTION NOTICE. For unclassified, limited documents, destroy by any method that will prevent
disclosure of contents or reconstruction of the document.
TABLE OF CONTENTS
Illus
Page Figure
Section I . Introduction...................................................................................................................... 1
*This manual supersedes TM 9-1015-234-20P, 21 December 1971, including all changes in their entirety.
Change 1 i
TM 9-1015-234-20P
TABLE OF CONTENTS-Continued
Illus
Page Figure
Change 1 ii
TM 9-1015-234-20P
TABLE OF CONTENTS-Continued
Illus
Page Figure
Change 1 iii
TM 9-1015-234-20P
ORGANIZATIONAL MAINTENANCE
REPAIR PARTS AND SPECIAL TOOLS LIST
Section I. INTRODUCTION
SCOPE
This RPSTL lists and authorizes spares and repair parts; special tools; special test, measurement, and diagnostic
equipment (TMDE); and other special support equipment required for performance of organizational maintenance of the
M102 Howitzer. it authorizes the requisitioning, issue, and disposition of spares, repair parts and special tools as indicated
by the source, maintenance and recoverability (SMR) codes.
GENERAL
In addition to Section I, Introduction, this Repair Parts and Special Tools List is divided into the following sections:
a. Section II. Repair Parts List. A list of spares and repair parts authorized by this RPSTL for use in the
performance of maintenance. The list also includes parts which must be removed for replacement of the authorized parts.
Parts lists are composed of functional groups in ascending alphanumeric sequence, with the parts in each group listed in
ascending figure and item number sequence. Bulk materials are listed in item name sequence. Repair parts kits are
listed separately in their own functional group within Section II. Repair parts for repairable special tools are also listed in
this section. Items listed are shown on the associated illustration(s)/figure(s)
b. Section III. Special Tools List. A list of special tools, special TMDE, and other special support equipment
authorized by this RPSTL (as indicated by Basis of Issue (BOI) information in DESCRIPTION AND USABLE ON CODE
column) for the performance of maintenance.
c. Section IV. National Stock Number and Part Number Index. A list, in National item identification number
(NIIN) sequence, of all National stock numbered items appearing in the listing, followed by a list in alphanumeric sequence
of all part numbers appearing in the listings. National stock numbers and part numbers are cross-referenced to each
illustration figure and item number appearance.
a. Item No. (Column (1)). Indicates the number used to identify items called out in the illustration.
1
TM 9-1015-234-20P
EXPLANATION OF COLUMNS (SECTIONS II AND III)-Continued
b. SMR Code (Column (2)). The Source, Maintenance, and Recoverability (SMR) code is a 5-position code
containing supply/requisitioning information, maintenance category authorization criteria, and disposition instruction, as
shown in the following breakout:
XX 1st two XX XX
positions
How you get an item. 3d Position 4th position Who determines
disposition action
Who can install Who can do on an unserviceable
replace or use complete repair* item.
the item. on the item.
*Complete Repair: Maintenance capacity, capability, and authority to perform all corrective maintenance tasks of the
"Repair" function in a use/user environment in order to restore serviceability to a failed item.
(1) Source Code. The source code tells you how to get an item needed for maintenance, repair. or
overhaul of an end item/equipment. Explanations of source codes follow:
Code
PA
PB
PC** Stocked items; use the applicable NSN to request/requisition items with these source codes. They
PD are authorized to the category indicated by the code entered in the 3d position of the SMR code.
PE
PF **Note: Items coded PC are subject to deterioration.
PG
KD Items with these codes are not to be requested/requisitioned individually. They are part of a kit which
KF is authorized to the maintenance category indicated in the 3d position of the SMR code. The
KB complete kit must be requisitioned and applied.
2
TM 9-1015-234-20P
Code Explanation
MO - (Made at Org/AVUM Items with these codes are not to be requested/requisitioned individually. They
Level) must be made from bulk material which is identified by the part number in the
MF - (Made at DS/AVIM DESCRIPTION AND USABLE ON CODE (UOC) column and listed in the bulk
Level) material group of the repair parts list in this RPSTL. If the item is authorized to
MH - (Made at GS Level) you by the 3d position code of the SMR code, but the source code indicates it is
ML - (Made at Specialized made at a higher level, order the item from the higher of maintenance.
Repair Act (SRA))
MD - (Made at Depot)
AO - (Assembled by Org/
AVUM Level) Items with these codes are not to be requested/requisitioned individually. The
AF - (Assembled by DS/AVIM parts that make up the assembled item must be requisitioned or fabricated and
Level) assembled at the level of maintenance indicated by the source code. If the 3d
AH - (Assembled by GS position code of the SMR code authorizes you to replace the item, but the source
Category) code indicates the item is assembled at a higher level, order the item from the
AL - (Assembled by SRA) higher level of maintenance.
AD - (Assembled by Depot)
XA - Do not requisition an "XA"-coded item. Order its next higher assembly. (Also, refer to the NOTE below.)
XB - If an "XB" item is not available from salvage, order it using the FSCM and part number given.
XC - Installation drawing, diagram, instruction sheet, field service drawing, that is identified by manufacturer’s part
number.
XD - Item is not stocked. Order an "XD"-coded item through normal supply channels using the FSCM and part number
given, if no NSN is available.
NOTE: Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items
with the above source codes, except for those source coded "XA" or those aircraft support items restricted by
requirements of AR 700-42.
3
TM 9-1015-234-20P
(2) Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to USE and
REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR code as follows:
(a) The maintenance code entered in the third position tells you the lowest maintenance level
authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate
authorization to one of the following levels of maintenance.
Code Application/Explanation
O Organizational or aviation unit category can remove, replace, and use the item.
F Direct support or aviation intermediate level can remove, replace, and use the item.
H General support level can remove, replace, and use the item.
L Specialized repair activity can remove, replace, and use the item.
(b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired
and identifies the lowest maintenance level with the capability to do complete repair (i.e., perform all authorized repair
functions). (NOTE: Some limited repair may be done on the item at a lower level of maintenance, if authorized by the
Maintenance Allocation Chart (MAC) and SMR codes.) This position will contain one of the following maintenance codes.
Code Application/Explanation
O Organizational or aviation unit is the lowest level that can do complete repair of the item.
F Direct support or aviation intermediate is the lowest level that can do complete repair of
the item.
H General support is the lowest level that can do complete repair of the item.
4
TM 9-1015-234-20P
Code Application/Explanation
L Specialized repair activity is the lowest level that can do complete repair of the item.
D Depot is the lowest level that can do complete repair of the item.
B No repair is authorized. (No parts or special tools are authorized for the maintenance of a
"B" coded item.) However, the item may be reconditioned by adjusting, lubricating, etc., at
the user level.
(3) Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action on
unserviceable items. The recoverability code is entered in the fifth position of the SMR Code as follows:
Recoverability
Codes Application/Explanation
Z Nonreparable item. When unserviceable, condemn and dispose of the item at the level of
maintenance shown in 3d position of SMR Code.
0 Reparable item. When uneconomically reparable, condemn and dispose of the item at
organizational or aviation unit level.
F Reparable item. When uneconomically reparable, condemn and dispose of the item at
the direct support or aviation intermediate level.
H Reparable item. When uneconomically reparable, condemn and dispose of the item at
the general support level.
D Reparable item. When beyond lower level repair capability, return to depot.
Condemnation and disposal of item not authorized below depot level.
L Reparable item. Condemnation and disposal not authorized below specialized repair
activity (SRA).
5
TM 9-1015-234-20P
c. FSCM (Column (3)). The Federal Supply Code for Manufacturer (FSCM) is a 5-digit numeric code which is
used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item.
d. Part Number (Column (4)). Indicates the primary number used by the manufacturer (individual, company,
firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its
engineering drawings, specifications standards, and inspection requirements to identify an item or range of items.
NOTE: When you use an NSN to requisition an item, the item you receive may have a different
part number from the part ordered.
e. Description and Usable On Code (UOC) (Column (5)). This column includes the following information:
(1) The Federal item name and, when required, a minimum description to identify the item.
(2) The physical security classification of the item is indicated by the parenthetical entry which is a physical
security classification abbreviation (e.g., Phy Sec C1 (C) - Confidential, Phy Sec C1 (S) - Secret, Phy Sec C1 (T) - Top
Secret).
(3) Items that are included in kits and sets are listed below the name of the kit or set.
(4) Spare/repair parts that make up an assembled item are listed immediately following the assembled item
line entry.
(5) Part numbers for bulk materials are referenced in this column in the line item entry for the item to be
manufactured/fabricated.
(6) When the item is not used with all serial numbers of the same model, the effective serial numbers are
shown on the last line(s) of the description (before UOC).
(7) The usable on code, when applicable. (see paragraph 5, Special information.)
(8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for each
special tool, special TMDE, and other special support equipment. When density of equipments supported exceeds density
spread indicated in the basis of issue, the total authorization is increased proportionately.
(9) The statement "END OF FIGURE" appears just below the last item description in Column 5 for a given
figure in both section II and section III.
6
TM 9-1015-234-20P
f. Qty (Column (6)). The QTY (quantity per figure column) indicates the quantity of the item used in the
breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group, or an assembly. A
“V” appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from
application to application.
(1) Stock Number Column. This column lists the NSN by National item identification number (NIIN)
NSN
sequence. The NIIN consists of the last nine digits of the NSN (i.e., 5305-01-674-1467). When using this column to
NIIN
locate an item, ignore the first 4 digits of the NSN. However, the complete NSN should be used when ordering items by
stock number.
(2) FIG. column. This column lists the number of the figure where the item is identified/located. The
figures are in numerical order in Section II and Section III.
(3) ITEM column. The item number identifies the item associated with the figure listed in the adjacent FIG.
Column. This item is also identified by the NSN listed on the same line.
b. Part Number Index. Part numbers in this index are listed by part number in ascending alphanumeric
sequence (i.e., vertical arrangement of letter and number combination which places the first letter or digit of each group in
order A through Z, followed by the numbers 0 through 9 and each following letter or digit in like order).
(1) FSCM column. The federal Supply Code for Manufacturer (FSCM) is a 5-digit numeric code used to
identify the manufacturer, distributor, or Government agency, etc., that supplies the item.
(2) Part Number column. Indicates the primary number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering
drawings, specifications standards, and inspection requirements to identify an item or range of items.
(3) Stock Number column. This column lists the NSN for the associated part number and manufacturer
identified in the PART NUMBER and FSCM columns to the left.
(4) Fig. column. This column lists the number of the figure where the item is identified/located in
Section II and III.
(5) Item column. The item number is that number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
7
TM 9-1015-234-20P
SPECIAL INFORMATION
a. Assembly Instruction. Detailed assembly instructions for items source coded to be assembled from
component spare repair parts are found in TM 9-1015-234-20. Items that make up the assembly are listed immediately
following the assembly item entry or reference is made to an applicable figure.
b. Associated Publications. The publications listed below pertain to M102 howitzer and its components:
c. Illustrations - Listing. The Illustrations In this RPSTL are identical to those published in TM 9 1200-208-34P
and TM 9-1015 234-34P. Only those parts codes "C" or "O" in the third position of the SMR Code are listed in the tabular
listing; therefore, there may be a break in the item number sequence. Only illustrations containing organizational or
aviation unit authorized items appear in this RPSTL.
(1) First. Using the Label of contents, determine the assembly group or subassembly group to which the
item belongs. This Is necessary since figures are prepared for assembly groups and subassembly groups, and listings are
divided into the same groups.
(2) Second. Find the figure covering the assembly group or subassembly group to which the item belongs.
(3) Third. Identify the item on the figure and note the item number.
(4) Fourth. Refer to the Repair Parts List for the figure to find the part number for the item number noted
on the figure.
(5) Fifth. Refer to the Part Number Index to find the NSN, if assigned.
8
TM 9-1015-234-20P
(1) First. Using the Index of National Stock Numbers and Part Numbers, find the pertinent National Stock
Number or Part Number. The NSN index is in National Item Identification Number (NIIN) sequence (see 4.a(1)). The part
numbers in the Part Number index are listed in ascending alphanumeric sequence (see 4.b). Both indexes cross-
reference you to the illustration figure and item number of the item you are looking for.
(2) Second. After finding the figure and item number, verify that the item is the one you’re looking for, then
locate the item number in the repair parts list for the figure.
ABBREVIATIONS
Not applicable.
9
SECTION II TM-9-1015-234-20P
GROUP 00
FIG. 1 HOWITZER, LIGHT, TOWED, 105-MM,
M102 8428300
END OF FIGURE
1-1
SECTION II TM-9-1015-234-20P
GROUP 0101
FIG. 2 BREECH MECHANISM ASSEMBLY
8769507
END OF FIGURE
2-1
SECTION II TM-9-1015-234-20P
GROUP 010101
FIG. 3 HANDLE ASSEMBLY 8769520
END OF FIGURE
3-1
SECTION II TM-9-1015-234-20P
GROUP 010102
FIG. 4 COCKING MECHANISM ASSEMBLY
8767262
END OF FIGURE
4-1
SECTION II TM-9-1015-234-20P
GROUP 010103
FIG. 5 MECHANISM, PERCUSSION 8767487
END OF FIGURE
5-1
SECTION II TM-9-1015-234-20P
GROUP 010104
FIG. 6 BREECH RING ASSEMBLY 8769503
END OF FIGURE
6-1
SECTION II TM-9-1015-234-20P
GROUP 02
FIG. 7 RECOIL MECHANISM, 105-MM
HOWITZER, M37A1 12000725
END OF FIGURE
7-1
SECTION II TM-9-1015-234-20P
GROUP 0201
FIG. 8 VALVE ASSEMBLY, OIL FILLING
8408547
END OF FIGURE
8-1
SECTION II TM-9-1015-234-20P
GROUP 0202
FIG. 9 PIN ASSEMBLY 8436745
END OF FIGURE
9-1
SECTION II TM-9-1015-234-20P
GROUP 0204
FIG. 10 CYLINDER ASSEMBLY, RECOIL
8432806
END OF FIGURE
10-1
SECTION II TM-9-1015-234-20P
Figure 11. Carriage, 105-MM Howitzer, M31 8433200, Cradle Assembly, Gun And Attaching Parts.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 03
FIG. 11 CARRIAGE, 105-MM HOWITZER, M31
8433200, CRADLE ASSEMBLY, GUN AND
ATTACHING PARTS
END OF FIGURE
11-1
SECTION II TM-9-1015-234-20P
Figure 12. Carriage, 105-MM Howitzer, M31 8433200, Elevating Mechanism and Firing Platform Assembly.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 03
FIG. 12 CARRIAGE, 105-MM HOWITZER, M31
8433200, ELEVATING MECHANISM AND
FIRING PLATFORM ASSEMBLY
END OF FIGURE
12-1
SECTION II TM-9-1015-234-20P
GROUP 03
FIG. 13 CARRIAGE, 105-MM HOWITZER, M31
8433200, TRAVERSING MECHANISM
END OF FIGURE
13-1
SECTION II TM-9-1015-234-20P
GROUP 03
FIG. 14 CARRIAGE, 105-MM HOWITZER, M31
8433200, SUSPENSION SYSTEM
END OF FIGURE
14-1
SECTION II TM-9-1015-234-20P
Figure 15. Carriage, 105-MM Howitzer, M31 8433200, Stowage and Firing Support Components.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 03
FIG. 15 CARRIAGE, 105-MM HOWITZER, M31
8433200, STOWAGE AND FIRING SUPPORT
COMPONENTS
END OF FIGURE
15-1
SECTION II TM-9-1015-234-20P
Figure 16. Carriage, 105-mm Howitzer, M31 8433200, Trial and Bracket Assembly And Attached Parts.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 03
FIG. 16 CARRIAGE, 1O5-MM HOWITZER, M31
8433200, TRAIL AND BRACKET ASSEMBLY
AND ATTACHED PARTS
END OF FIGURE
16-1
SECTION II TM-9-1015-234-20P
GROUP 0302
FIG. 17 CRADLE ASSEMBLY, GUN 8433202
END OF FIGURE
17-1
SECTION II TM-9-1015-234-20P
GROUP 030202
FIG. 18 PIN ASSEMBLY, TRAVEL LOCK
8436597
END OF FIGURE
18-1
SECTION II TM-9-1015-234-20P
GROUP 0303
FIG. 19 ADAPTER, FIRE CONTROL, M14A1
QUADRANT 11739590
END OF FIGURE
19-1
SECTION II TM-9-1015-234-20P
GROUP 0307
FIG. 20 BUFFER ASSEMBLY 8433500
END OF FIGURE
20-1
SECTION II TM-9-1015-234-20P
GROUP 0309
FIG. 21 SUPPORT ASSEMBLY, LEFT HAND
8432784
END OF FIGURE
21-1
SECTION II TM-9-1015-234-20P
GROUP 0310
FIG. 22 SUPPORT ASSEMBLY, RIGHT HAND
8432785
END OF FIGURE
22-1
SECTION II TM-9-1015-234-20P
GROUP 0311
FIG. 23 HANDWHEEL ASSEMBLY, ELEVATING
8447268
END OF FIGURE
23-1
SECTION II TM-9-1015-234-20P
GROUP 0312
FIG. 24 GEAR HOUSING ASSEMBLY, UPPER
ELEVATING 8432579
END OF FIGURE
24-1
SECTION II TM-9-1015-234-20P
GROUP 0313
FIG. 25 GEAR AND HOUSING ASSEMBLY,
LOWER ELEVATING 8432580
END OF FIGURE
25-1
SECTION II TM-9-1015-234-20P
Figure 26. Ball Screw And Equilibrator Assembly Without Springs 8430302.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 031401
FIG. 26 BALL SCREW AND EQUILIBRATOR
ASSEMBLY WITHOUT SPRINGS 8430302
END OF FIGURE
26-1
SECTION II TM-9-1015-234-20P
Figure 27. Ball Screw And Equilibrator Assembly Without Springs 8430302 Gear Housing.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 031401
FIG. 27 BALL SCREW AND EQUILIBRATOR
ASSEMBLY WITHOUT SPRINGS 8430302
GEAR HOUSING
END OF FIGURE
27-1
SECTION II TM-9-1015-234-20P
GROUP 0315
FIG. 28 HANDWHEEL ASSEMBLY
(TRAVERSING) 8423255
END OF FIGURE
28-1
SECTION II TM-9-1015-234-20P
GROUP 0316
FIG. 29 GEAR AND HOUSING ASSEMBLY
(HDWL) 8432442
END OF FIGURE
29-1
SECTION II TM-9-1015-234-20P
GROUP 0317
FIG. 30 GEAR AND HOUSING ASSEMBLY
(INTMED) 8432441
END OF FIGURE
30-1
SECTION II TM-9-1015-234-20P
GROUP 0318
FIG. 31 TRAVERSE HOUSING ASSEMBLY
8432439
END OF FIGURE
31-1
SECTION II TM-9-1015-234-20P
GROUP 0319
FIG. 32 HOUSING ASSEMBLY, FRONT
8436560
END OF FIGURE
32-1
SECTION II TM-9-1015-234-20P
GROUP 0321
FIG. 33 WHEEL ASSEMBLY 8432536
END OF FIGURE
33-1
SECTION II TM-9-1015-234-20P
Figure 34. Spindle, Brake and Support Assembly, Left Hand 9347121 and 8436578 (Unmodified) and Spindle, Brake and
Support Assembly, Right Hand 9347122 and 8436579 (Unmodified).
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 0322
FIG. 34 SPINDLE, BRAKE AND SUPPORT
ASSEMBLY, LEFT HAND 9347121 AND
8436578 (UNMODIFIED) AND GROUP 0323
SPINDLE, BRAKE AND SUPPORT ASSEMBLY,
RIGHT HAND 9347122 AND 8436579
(UNMODIFIED)
END OF FIGURE
34-1
SECTION II TM-9-1015-234-20P
Figure 35. Hub And Brake Drum Assembly 9347123 and 8433605 (Unmodified).
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
END OF FIGURE
35-1
SECTION II TM-9-1015-234-20P
END OF FIGURE
35A-1
SECTION II TM-9-1015-234-20P
GROUP 0326
FIG. 36 PIN ASSEMBLY (SUSPENSION)
8436746
END OF FIGURE
36-1
SECTION II TM-9-1015-234-20P
GROUP 0327
FIG. 37 BRACKET ASSEMBLY, SIGHT CASE
STOWAGE 8447298
END OF FIGURE
37-1
SECTION II TM-9-1015-234-20P
GROUP 0329
FIG. 38 TRAIL AND BRACKET ASSEMBLY
8433206
END OF FIGURE
38-1
SECTION II TM-9-1015-234-20P
GROUP 0330
FIG. 39 PIN ASSEMBLY 8436745
8433206
END OF FIGURE
39-1
SECTION II TM-9-1015-234-20P
GROUP 04
FIG. 40 TELESCOPE, PANORAMIC, M113A1
11730267
END OF FIGURE
40-1
SECTION II TM-9-1015-234-20P
GROUP 06
FIG. 41 TELESCOPE, ELBOW, M114A1
11730285
END OF FIGURE
41-1
SECTION II TM-9-1015-234-20P
Figure 42. Telescope, Elbow, M114A1 11730285, Housing And Attaching Parts.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 06
FIG. 42 TELESCOPE, ELBOW, M114A1
11730285, HOUSING AND ATTACHING
PARTS
END OF FIGURE
42-1
SECTION II TM-9-1015-234-20P
GROUP 07
FIG. 43 QUADRANT, FIRE CONTROL, M14A1
11730915
END OF FIGURE
43-1
SECTION II TM-9-1015-234-20P
GROUP 08
FIG. 44 CRANK ASSEMBLY 8432902
END OF FIGURE
44-1
SECTION II TM-9-1015-234-20P
GROUP 09
FIG. 45 DELETED
45-1
SECTION II TM-9-1015-234-20P
GROUP 10
FIG. 46 TAIL AND STOP BLACKOUT LIGHT
12953546
END OF FIGURE
46-1
SECTION II TM-9-1015-234-20P
GROUP 1001
FIG. 47 VEHICULAR STOP LIGHT-TAIL
LIGHT MS52125-2
END OF FIGURE
47-1
SECTION II TM-9-1015-234-20P
GROUP 1002
FIG. 48 DELETED
48-1
SECTION II TM-9-1015-234-20P
GROUP 11
FIG. 49 COVER, OVERALL 12000773
END OF FIGURE
49-1
SECTION II TM-9-1015-234-20P
GROUP 12
FIG. 50 DELETED
50-1
SECTION II TM-9-1015-234-20P
GROUP 13
FIG. 51 CASE, CARRYING 11729600-2
END OF FIGURE
51-1
SECTION II TM-9-1015-234-20P
GROUP 14
FIG. 52 ALINEMENT DEVICE, M140
11741648-2
END OF FIGURE
52-1
SECTION II TM-9-1015-234-20P
M1A1
GROUP 15
FIG. 53 COLLIMATOR, INFINITY AIMING,
M1A1 10556235
END OF FIGURE
53-1
SECTION II TM-9-1015-234-20P
Figure 54. Quadrant, Fire Control, Gunner’s M1A1 (With Carrying Case) 7197156.
SECTION II TM 9-1015-234-20P, CO1
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 16
FIG. 54 QUADRANT, FIRE CONTROL, GUNNERS
M1A1 (WITH CARRYING CASE) 7197156
END OF FIGURE
54-1
SECTION II TM-9-1015-234-20P
Figure 55. Light, Aiming Post, M58 11730975 And Light, Aiming Post, M59 11730976.
SECTION II TM 9-1015-234-20P
(1) (2) (3) (4) (5) (6)
ITEM SMR PART
NO CODE FSCM NUMBER DESCRIPTION AND USABLE ON CODES (UOC) QTY
GROUP 17
FIG. 55 LIGHT, AIMING POST, M58
11730975 AND GROUP 18 LIGHT, AIMING
POST, M59 11730976
END OF FIGURE
55-1
SECTION II TM-9-1015-234-20P
GROUP 19
FIG. 56 POST, AIMING, M1A2 7687114
END OF FIGURE
56-1
SECTION II TM-9-1015-234-20P
GROUP 20
FIG. 57 FIXTURE AND CASE, GUN TUBE
LEVELING 11578744
57-1
TM 9-1015-234-20P, CO1
SECTION III. SPECIAL TOOLS LIST
GROUP 9502
FIG. 58 SPECIAL TOOLS(REPAIR PARTS)
END OF FIGURE
58-1
SECTION IV TM 9-1015-234-20P
CROSS- REFERENCE-INDEXES
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER FIG. ITEM STOCK NUMBER FIG. ITEM
1240-00-009-0027 41 2 3020-00-148-7552 19 3
3020-00-012-4485 2 19 1240-00-150-8886 1 18
4730-00-018-9566 20 1 1240-00-150-8889 1 11
6240-00-019-3093 47 2 1240-00-150-8890 1 17
4730-00-027-6596 32 5 1290-00-150-8891 1 10
6240-00-044-6914 47 1 5320-00-165-8787 46 6
5310-00-045-3296 37 6 5310-00-167-0721 15 25
4730-00-050-4208 21 12 5340-00-171-0756 40 20
22 12 5340-00-171-0757 41 3
23 6 4730-00-172-0010 11 2
31 7 14 13
5305-00-054-5636 52 6 26 3
5305-00-054-5648 19 5 5315-00-177-3930 16 33
5305-00-057-0523 40 22 6220-00-179-4324 47 4
41 1 1015-00-180-5372 5 5
5315-00-058-6078 4 3 5305-00-182-7302 40 23
5315-00-058-6115 2 18 5315-00-187-9549 7 18
3 2 5315-00-187-9550 34 16
5315-00-059-0206 16 1 5360-00-191-1364 3 5
2640-00-060-3543 52 13 5340-00-197-6295 25 9
53 3 9905-00-205-2795 49 3
5310-00-061-1258 46 21 5310-00-209-0786 14 3
5315-00-063-7366 34 5 5310-00-209-0788 13 35
5305-00-068-0508 14 2 21 8
5330-00-073-0171 34 9 22 9
5330-00-073-0200 29 14 24 13
5330-00-073-0218 30 12 25 8
1015-00-073-0252 2 34 29 16
5340-00-073-0253 2 23 30 14
5315-00-073-0254 2 33 5935-00-221-8620 46 7
5315-00-073-0255 2 25 1650-00-222-4525 53 2
3040-00-073-0256 2 31 4730-00-223-9267 26 23
5360-00-073-0257 2 32 5306-00-225-9088 7 28
5340-00-073-0264 2 20 5306-00-226-4830 15 24
5340-00-073-2041 34 3 5315-00-234-1854 52 10
9390-00-073-2055 20 23 5315-00-236-8356 17 5
5310-00-073-5368 10 21 5340-00-237-3943 29 15
3040-00-073-5371 7 23 5325-00-249-6355 46 18
5340-00-073-5372 1 12 9905-00-257-2746 42 21
3040-00-073-5381 2 27 52 3
5315-00-075-5828 12 24 55 1
5310-00-080-6004 46 20 2610-00-269-7378 33 2
5305-00-085-3706 53 1 5310-00-274-8707 2 21
5315-00-105-4155 44 4 5340-00-282-8243 15 23
5360-00-113-1515 7 25 1095-00-317-2484 11 9
4820-00-114-1096 52 14 4933-00-340-1126 57 2
3040-00-116-5171 35A 6 2530-00-350-8707 35 4
5365-00-139-4646 2 17 5340-00-401-4373 3 1
5315-00-143-6045 2 24 5310-00-407-9566 7 27
5340-00-148-7551 19 2 5365-00-423-1510 49 4
I-1
SECTION IV TM 9-1015-234-20P, CO1
CROSS- REFERENCE-INDEXES
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER FIG. ITEM STOCK NUMBER FIG. ITEM
I-2
SECTION IV TM 9-1015-234-20P, CO1
CROSS- REFERENCE-INDEXES
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER FIG. ITEM STOCK NUMBER FIG. ITEM
1015-00-863-1057 5 2 1015-01-003-9802 7 5
5360-00-863-1059 2 4 9905-01-005-6034 51 2
5305-00-889-3000 29 17 5315-01-021-0799 35A 3
5360-00-893-9329 6 9 3040-01-021-0800 35A 9
5310-00-894-2246 52 9 5306-01-021-0801 35A 11
5315-00-894-4237 4 4 5365-01-021-0802 35A 10
5315-00-900-1841 28 7 5360-01-022-6824 35A 12
1015-00-902-3714 2 35 1015-01-028-4582 1 15
1015-00-902-3718 2 36 2530-01-032-6676 35A 1
5310-00-902-7846 23 1 5975-01-034-5871 46 11
3110-00-902-9334 21 10 7690-01-043-7427 52 2
22 15 2530-01-043-7492 35A 2
5310-00-902-9369 13 11 5340-01-043-7517 52 7
5310-00-905-0762 49 1 5340-01-043-7938 15 21
4730-00-908-3193 20 18 9905-01-043-9365 52 15
1290-00-910-3678 54 1 5340-01-044-7045 51 1
5305-00-914-3783 38 5 5305-01-047-0996 52 8
5306-00-915-5710 34 4 5306-01-059-5912 46 3
5360-00-919-7267 2 2 4010-01-065-9727 18 3
5310-00-925-9642 12 21 36 1
5310-00-925-9645 46 17 5340-01-068-8817 24 14
1015-00-927-7275 12 26 5340-01-068-8818 27 3
5310-00-929-6395 40 21 5340-01-068-8819 30 13
5310-00-933-8118 19 4 5315-01-070-1157 9 1
5310-00-934-9758 37 7 39 1
46 10 4933-01-071-0562 58 11
5365-00-936-2308 34 15 3010-01-072-4435 44 1
5330-00-937-2815 25 10 5140-01-073-7598 58 12
5330-00-937-2816 24 15 5330-01-079-9597 27 4
5340-00-937-7325 14 5 6220-01-093-4439 46 1
5340-00-937-9588 46 15 1015-01-114-8014 44 3
5120-00-939-0543 58 9 5305-01-121-8473 38 4
5310-00-951-7209 12 22 4710-01-139-7427 56 2
5340-00-954-3134 46 5 4710-01-139-7428 56 1
5315-00-954-3472 2 14 5330-01-140-2513 34 14
5305-00-955-2941 52 1 1015-01-140-2580 34 10
5305-00-958-5245 49 5 2530-01-143-9389 33 3
5305-00-959-6865 42 22 5340-01-144-8032 38 6
5340-00-973-4723 2 28 1015-01-145-4701 58 13
5305-00-978-9347 30 15 5365-01-150-7579 34 15
5330-00-983-6971 13 33 5310-01-174-8759 34 13
5305-00-984-4988 13 36 5310-01-180-4783 34 11
24 12 5310-01-180-8706 34 12
25 7 5995-01-202-0239 46 19
5305-00-984-6210 27 1 5330-01-211-5058 34 9
37 3 1015-01-235-0223 40 30
5305-00-984-6211 46 4 42 15
4030-00-987-8738 1 13 43 29
5305-00-990-0695 7 7 52 11
5315-00-999-1573 44 5 6220-01-284-2709 47 6
I-3
SECTION IV TM 9-1015-234-20P, CO1
CROSS- REFERENCE-INDEXES
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER FIG. ITEM STOCK NUMBER FIG. ITEM
6220-01-297-3217 47 5
7690-01-368-7024 53 4
I-4
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-5
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-6
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-7
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-8
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-9
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
19204 8436499 18 1
39 4
19204 8436590 4030-00-987-8738 1 13
19204 8436591 5340-00-937-7325 14 5
19204 8436594 1015-00-829-6356 16 31
36 4
19204 8436595 1015-00-829-6321 17 4
18 4
19204 8436596 4010-01-065-9727 18 3
36 1
19204 8436597 5315-00-829-6476 17 14
19204 8436691 36 3
19204 8436693 2990-00-829-6361 9 3
39 3
19204 8436743 5315-01-070-1157 9 1
39 1
19204 8436745 5315-00-829-6486 7 19
16 3
19204 8436746 5315-00-829-6490 14 4
19204 8436773 1015-00-658-0794 1 14
19204 8447268 5340-00-439-1774 12 20
19204 8447269 23 3
19204 8447270 5340-00-458-9830 23 4
19204 8447271 1015-00-553-1707 23 5
19204 8447296 5340-00-470-4275 37 2
19204 8447297 5340-00-459-3288 37 1
19204 8447355 5365-00-423-1510 49 4
19200 8449338 4933-01-071-0562 58 11
19204 8449343 5140-01-073-7598 58 12
19200 8587448-2 5340-00-171-0756 40 20
19200 8587448-3 5340-00-171-0757 41 3
19200 8626469 5305-00-959-6865 42 22
19206 8767251 1095-00-863-1042 2 3
19206 8767255 5315-00-863-1046 2 29
19206 8767256 5340-00-863-1047 2 16
19206 8767257 1015-00-863-1048 2 1
19206 8767260 3120-00-863-1051 4 2
19206 8767261 1015-00-863-1052 4 1
19206 8767262 2 40
19206 8767263 5360-00-863-1053 2 15
19206 8767264 1015-00-863-1054 2 6
19206 8767265 1015-00-863-1055 2 5
19206 8767270 1015-00-863-1057 5 2
19206 8767276 5360-00-863-1059 2 4
19206 8767487 2 39
19206 8768730 5930-00-820-3198 2 26
19206 8769167 5340-00-973-4723 2 28
19206 8769505 3020-00-012-4485 2 19
19206 8769508 1015-00-073-0252 2 34
19206 8769509 5340-00-073-0253 2 23
19206 8769510 5315-00-073-0254 2 33
I-10
SECTION IV TM 9-1015-234-20P, CO1
CROSS-REFERENCE INDEXES
PART NUMBER INDEX
I-11
SECTION IV TM 9-1015-234-20P, CO1
I-12
SECTION IV TM 9-1015-234-20P, CO1
I-13
SECTION IV TM 9-1015-234-20P, CO1
I-14
SECTION IV TM 9-1015-234-20P, CO1
I-15
SECTION IV TM 9-1015-234-20P, CO1
I-16
SECTION IV TM 9-1015-234-20P, CO1
46 2 19204 8433178
46 3 5306-01-059-5912 96906 MS18154-58L
46 4 5305-00-984-6211 96906 MS35206-264
46 5 5340-00-954-3134 96906 MS25281-R7
46 6 5320-00-165-8787 96906 MS20426B6-8
46 7 5935-00-221-8620 96906 MS25043-20D
46 8 5305-00-543-2732 96906 MS35265-18
46 9 5310-00-584-5272 96906 MS35338-48
46 10 5310-00-934-9758 96906 MS35649-202
46 11 5975-01-034-5871 96906 MS3367-7-0
46 12 19204 8433179
46 13 5315-00-844-3665 96906 MS16562-68
46 14 5315-00-843-7986 96906 MS16562-33
46 15 5340-00-937-9588 19204 8432554
46 16 5310-00-759-2807 19204 8433176
46 17 5310-00-925-9645 96906 MS21083N04
46 18 5325-00-249-6355 96906 MS35489-75
46 19 5995-01-202-0239 19200 12010502
46 20 5310-00-080-6004 96906 MS27183-14
46 21 5310-00-061-1258 96906 MS45904-76
46 22 9505-00-684-4843 96906 MS20995-F41
46 23 81349 M23053/1-107-0
47 1 6240-00-044-6914 96906 MS35478-1683
47 2 6240-00-019-3093 96906 MS15570-623
47 3 5330-00-462-0907 19207 11639519-2
47 4 6220-00-179-4324 19207 11639535
47 5 6220-01-297-3217 19207 12360870-2
47 6 6220-01-284-2709 19207 12360850-1
49 1 5310-00-905-0762 96906 MS51967-3
49 2 5310-00-550-1130 96906 MS35333-40
49 3 9905-00-205-2795 96906 MS35387-1
49 4 5365-00-423-1510 19204 8447355
49 5 5305-00-958-5245 96906 MS35190-288
51 1 5340-01-044-7045 19200 11739592
51 2 9905-01-005-6034 19200 11731008-6
52 1 5305-00-955-2941 19200 10555157-4
52 2 7690-01-043-7427 19200 11739593
52 3 9905-00-257-2746 19200 11731011
52 5 5310-00-543-4652 96906 MS35333-69
52 6 5305-00-054-5636 96906 MS51957-2
52 7 5340-01-043-7517 19200 10544452
52 8 5305-01-047-0996 19200 10544465
52 9 5310-00-894-2246 96906 MS35692-3
52 10 5315-00-234-1854 96906 MS24665-153
52 11 1015-01-235-0223 19200 8200055
52 12 5340-00-464-4792 19200 10516567
52 13 2640-00-060-3543 96906 MS51377-2
52 14 4820-00-114-1096 96906 MS51607-1
52 15 9905-01-043-9365 19200 10544467
53 1 5305-00-085-3706 19200 10555157-1
53 2 1650-00-222-4525 96906 MS20813-1
I-17
SECTION IV TM 9-1015-234-20P, CO1
I-18
TM 9-1015-234-20P
By Order of the Secretary of the Army:
R. L. DILWORTH
Brigadier General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-40, Unit Maintenance requirements for Howitzer, Light, Towed. 105MM,
M102.
1 Centimeter = 10 Millimeters = 0.01 Meters = 0.3937 Inches 1 Sq. Centimeter = 100 Sq. Millimeters = 0.155 Sq. Inches
1 Meter = 100 Centimeters = 1000 Millimeters = 39.37 Inches 1 Sq. Meter = 10,000 Sq. Centimeters = 10.76 Sq. Feet
1 kilometer = 1000 Meters = 0.621 Miles 1 Sq. Kilometer = 1,000,000 Sq. Meters = 0.386 Sq. Miles
1 Gram = 0.001 Kilograms = 1000 Milligrams = 0.035 Ounces 1 Cu. Centimeter = 1000 Cu. Millimeters = 0.06 Cu. Inches
1 Kilogram = 1000 Grams = 2.2 Lb. 1 Cu. Meter = 1,000,000 Cu. Centimeters = 35.31 Cu. Feet
1 Metric Ton = 1000 Kilograms = 1 Megagram = 1.1 Short Tons
TEMPERATURE
LIQUID MEASURE
5/9 (°F - 32) = °C
1 Milliliter = 0.001 Liters = 0.0338 Fluid Ounces 212° Fahrenheit is equivalent to 100° Celsius
1 Liter = 1000 Milliliters 33.82 Fluid Ounces 90° Fahrenheit is equivalent to 32.2° Celsius
32° Fahrenheit is equivalent to 0° Celsius
9/5 (°C + 32) = °F
TO CHANGE TO MULTIPLY BY