Professional Documents
Culture Documents
INSTALL GUIDE
FLC-AL(DL)-CH4-EN
AVAILABLE FOR : FLCAN
Rev. Date: April 25, 2018
Doc. No.: ##50361##
TERMS OF USE: Automotive Data solutions Inc. (“ADs”) products are strictly intended for installation by Certified Technicians who are
employed by a registered business specialized in the installation of automotive aftermarket electronics products. prior to beginning
installation of an ADs product in a vehicle, it is the Certified Technician’s responsibility to review the most current product guide, Install
guide and vehicle-specific notes available in Weblink®. ADs is not responsible for any damages whatsoever, including but not limited
to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss
of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its
products. ADs reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-
Certified Technicians, non-compliant Certified Technicians or end users.
ALL IN ONE
INSTALL GUIDE Chrysler/Dodge/Jeep
U.S. Patent No. 8,856,780
TACHOMETER OUTPUT
RAP SHUTDOWN CTRL
SECURE TAKEOVER
PRIORITY UNLOCK
E-BRAKE OUTPUT
POWER LIFTGATE
ARM OEM ALARM
DOOR UNLOCK
INSTALL TYPE
DOOR LOCK
MODEL
MAKE
YEAR
CHRYSLER
300 08-10 1 or 2 • • • • • • • • • • • • •
Caravan 08-10 1 or 2 • • • • • • • • • • • • • • • • • •
Challenger 08-14 1 or 2 • • • • • • • • • • • • • • •
Charger 08-10 1 or 2 • • • • • • • • • • • • •
DODGE
Durango 11-13 1 or 2 • • • • • • • • • • • • •
Grand Caravan 08-17 1 or 2 • • • • • • • • • • • • • • • • • •
Journey 09-10 1 or 2 • • • • • • • • • • • • • •
Magnum 08 1 or 2 • • • • • • • • • • • • •
Ram 1500 09 1 or 2 • • • • • • • • • • • •
Commander 08-10 1 or 2 • • • • • • • • • • • •
JEEP
3500 10-12 1 or 2 • • • • • • • • • • • •
4500 11-12 1 or 2 • • • • • • • • • • • •
5500 11-12 1 or 2 • • • • • • • • • • • •
VOLKSWAGEN
Routan 09-12 1 or 2 • • • • • • • • • • • • • • • • • •
DR
!
SHUTDOWN IS REQUIRED
VE ER
REFER TO
IV
HI DO
ASSEMBLY FOR PROPER
REMOTE STARTER
CL O
CONNECTIONS AND MATCH
E RP
(- IN
EACH LETTER ACCORDINGLY
) F
REARM (-) OUTPUT <- REQUIRED IGNITION OUTPUT - PINK
TACH (AC) INPUT <- REQUIRED GROUND INPUT - BLACK
E-BRAKE STATUS (-) INPUT <- REQUIRED 12V (+) INPUT - RED/WHITE
STARTER (+) OUTPUT <- REQUIRED BRAKE INPUT - ORANGE
PARKING LIGHT (+) OUTPUT <- REQUIRED
RIGHT SLIDING DOOR (-) OUTPUT <- REQUIRED DO NOT USE THE RED/WHITE
WIRE IF YOU ARE PLANNING
LEFT SLIDING DOOR (-) OUTPUT <- REQUIRED TO POWER THE VEHICLE
DISARM ONLY (-) OUTPUT <- REQUIRED POSITIVE PARKLIGHTS WIRE.
TRUNK (-) OUTPUT <- REQUIRED
UNLOCK (-) OUTPUT <- REQUIRED OPTIONAL -> PARKING LIGHT (+) OUTPUT
LOCK (-) OUTPUT <- REQUIRED OPTIONAL -> TRUNK STATUS (-) INPUT
GROUND WHEN RUNNING (-) OUTPUT <- REQUIRED OPTIONAL -> DOOR STATUS (-) INPUT
DATA MODE
LEGEND
N/A NOT REQUIRED IN DATA MODE (1-WAY)
NOT REQUIRED IN DATA MODE (2-WAY)
A G
DATA MODE
B
LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW
RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK WARNING
PARKING LIGHT (+) INPUT - WHITE USE THIS OUTPUT ONLY
ON VEHICLES EQUIPPED
STARTER (+) INPUT - BLACK/WHITE WITH MUX PARKING
E-BRAKE STATUS (-) OUTPUT - GREEN LIGHT CONTROL
TACH (AC) OUTPUT - PURPLE/WHITE
VE
HI
C
CL
THE BRAKE STATUS WIRE IS FUNCTIONAL
E
PA
ONLY WHEN THE IGNITION IS POWERED.
R
KI
NG
87
LI
GH
87A
T
85 86
(M
IF YOUR MODULE
UX
HARDWARE IS VERSION
)W
1.23 OR NEWER YOU
IR
CAN ELIMINATE THE
E
30
RELAY AND CONNECT
THE YELLOW WIRE
DIRECTLY TO THE VEHICLE
F
E
D A
E B
D A
B
C
OR C
F G
G
WWW.FLASHLOGIC.COM Automotive Data Solutions Inc. © 2018
ALL IN ONE
INSTALL GUIDE Chrysler/Dodge/Jeep
U.S. Patent No. 8,856,780
COMPONENT
CONNECTOR
CONNECTOR
CONNECTOR
LOCATION
POLARITY
POSITION
LOCATOR
MODULE
MODEL
COLOR
COLOR
NAME
MAKE
YEAR
WIRE
WIRE
TYPE
CanH ~ ~ 12 pin 5 White/Black (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
300 08-10 Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White/Brown MUX At switch or driver kick panel ~
CanH ~ ~ 12 pin 5 White/LtBlue (DATA) Ignition node ~
CHRYSLER
COMPONENT
CONNECTOR
CONNECTOR
CONNECTOR
LOCATION
POLARITY
POSITION
LOCATOR
MODULE
MODEL
COLOR
COLOR
NAME
MAKE
YEAR
WIRE
WIRE
TYPE
CanH ~ ~ 12 pin 5 White/LtBlue (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/Brown (DATA) Ignition node ~
Journey 09-10 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White/Purple (+) Passenger kick panel ~
CanH ~ ~ 12 pin 5 White/Black (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
DODGE
Magnum 08 Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White/Brown MUX Parking light switch ~
CanH ~ ~ 12 pin 5 White/LtGreen (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
Ram 1500 09 Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White MUX Parking light switch ~
CanH ~ ~ 12 pin 5 White/LtGreen (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
Commander 08-10 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver door ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ N/A (-) At pin 1 of relay 7 in IPM ~
CanH ~ Black 12 pin 5 White/LtGreen (DATA) Ignition node ~
CanL ~ Black 12 pin 6 White/LtBlue (DATA) Ignition node ~
JEEP
Grand 08-10 Driver Door Pin ~ ~ 20 pin 5 Purple (-) Driver door module ~
Cherokee
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ 1 N/A (-) At pin 1 of relay 7 in IPM, under hood ~
CanH ~ Black 12 pin 5 White/LtBlue (DATA) Ignition node ~
CanL ~ Black 12 pin 6 White/Brown (DATA) Ignition node ~
Grand 11-13 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel, door harness ~
Cherokee
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ Black 10 pin 1 White/LtGreen (MUX) Headlight switch ~
CanH ~ ~ 12 pin 5 White/LtGreen (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
1500 / 2500 / 10-12 Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~
3500
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White MUX Parking light switch ~
CanH ~ ~ 12 pin 5 White/LtGreen (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/LtBlue (DATA) Ignition node ~
RAM
4500 / 5500 11-12 Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White MUX Parking light switch ~
CanH ~ ~ 12 pin 5 White/LtBlue (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/Brown (DATA) Ignition node ~
C/V 10 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White/Brown MUX Parking light switch ~
COMPONENT
CONNECTOR
CONNECTOR
CONNECTOR
LOCATION
POLARITY
POSITION
LOCATOR
MODULE
MODEL
COLOR
COLOR
NAME
MAKE
YEAR
WIRE
WIRE
TYPE
CanH ~ ~ 12 pin 5 White/LtBlue (DATA) Ignition node ~
CanL ~ ~ 12 pin 6 White/Brown (DATA) Ignition node ~
RAM
C/V 11-15 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~
Ignition ~ ~ 12 pin 3 Pink/White (+) Ignition node ~
Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~
CanH ~ ~ 12 pin 5 White/LtBlue (DATA) Ignition node ~
VOLKSWAGEN
VE UX
USE THIS OUTPUT ONLY ON
(M
HI ) W
VEHICLES EQUIPPED WITH
CL I
MUX PARKING LIGHT CONTROL
E RE
PA
RK
ING
ONLY WHEN RAP
LI
G
SHUTDOWN IS REQUIRED
HT
VE
HI
CL
IF YOUR MODULE
E
DR
HARDWARE IS VERSION
IV
1.23 OR NEWER YOU
RE
CAN ELIMINATE THE
DO
RELAY AND CONNECT
OR
REMOTE STARTER THE YELLOW WIRE
PI
DIRECTLY TO THE VEHICLE
N
87
(-
TACH (AC) INPUT <- REQUIRED
)
E-BRAKE STATUS (-) INPUT <- REQUIRED 87A
STARTER (+) OUTPUT <- REQUIRED 85 86
PARKING LIGHT (+) OUTPUT <- REQUIRED
5 AMPS
RIGHT SLIDING DOOR (-) OUTPUT <- REQUIRED
LEFT SLIDING DOOR (-) OUTPUT <- REQUIRED REQUIRED -> REARM (-) OUTPUT 30
DISARM (+) OUTPUT <- REQUIRED REQUIRED -> PARKING LIGHT (+) OUTPUT
TRUNK (-) OUTPUT <- REQUIRED REQUIRED -> 1ST IGNITION (+) INPUT
UNLOCK (-) OUTPUT <- REQUIRED
LOCK (-) OUTPUT <- REQUIRED REQUIRED -> GLOW PLUG (+) INPUT DIESEL VEHICLES
12V (+) <- REQUIRED REQUIRED -> BRAKE (+) INPUT
1N4001
DIODE
GROUND (-) <- REQUIRED OPTIONAL -> TRUNK STATUS (-) INPUT
GROUND WHEN RUNNING (-) OUTPUT <- REQUIRED OPTIONAL -> DOOR STATUS (-) INPUT
DATA MODE
LEGEND WARNING
N/A NOT REQUIRED IN DATA MODE (1-WAY) REMOTE STARTER START OUTPUT
NOT REQUIRED IN DATA MODE (2-WAY) MUST BE EXTENDED TO ITS MAXIMUM
WHEN USING TACHLESS MODE
(CRANK TIME: AT LEAST 2.5 SECONDS)
USE DATA MODE OR USE TACH CONNECTION INSTEAD
OR HARDWIRE MODE
DATA MODE
WHITE/BLACK - IGNITION (+) VEHICLE SIDE
GWR (-) INPUT - BLUE/WHITE WHITE/RED - IGNITION (+) CONNECTOR SIDE
(NC) WHITE WHITE
GROUND - BLACK
12V (+) - RED
YELLOW/BLACK - DOOR STATUS (-) OUTPUT
LOCK/ARM (-) INPUT - GREEN/BLACK YELLOW/RED - TRUNK STATUS (-) OUTPUT
UNLOCK/DISARM (-) INPUT - BLUE/BLACK YELLOW - MULTIPLEX PARKING LIGHT OUTPUT
TRUNK (-) INPUT - RED/WHITE
DISARM ONLY (-) INPUT - BROWN BROWN/RED - CANH
LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW BROWN/YELLOW - CANL
RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK ORANGE/BLACK (NC)
PARKING LIGHT (+) INPUT - WHITE ORANGE/WHITE (NC)
STARTER (+) INPUT - BLACK/WHITE ORANGE - BRAKE STATUS (+) OUTPUT
E-BRAKE STATUS (-) OUTPUT - GREEN PINK/BLACK - GLOW PLUG (+) OUTPUT
TACH (AC) OUTPUT - PURPLE/WHITE PINK - IGNITION (+) INPUT VEHICLE SIDE
BLUE/RED (NC)
BLUE/YELLOW (NC)
GREEN/RED (NC)
GREEN/YELLOW (NC)
GRAY/RED - IGNITION (+) INPUT FROM KEY
GRAY/YELLOW (NC)
)
(+
ON
NL NH
TI
NI
CA CA
IG
WARNING
FOR SECURE TAKE OVER, CONNECT THE
BRAKE STATUS WIRE TO THE REMOTE STARTER.
1 2 3 4 5 6
DO NOT CONNECT TO THE VEHICLE BRAKE WIRE,
IT VOIDS THE SECURE TAKE OVER FEATURE.
1 2
Press and release Press and hold
programming button programming button
to select installation mode. until LED turns solid GREEN
to register selection.
!
LED flashes (1X) once = DATA MODE After registration, follow Factory Reset Procedure to
LED flashes (2X) twice = STANDARD HARDWIRE MODE change installation mode and restart this procedure.
1 6
Close driver door. Turn key to OFF position.
OFF
7
Re-open driver door to wake up Remove key.
data bus.
2
Insert key into ignition.
8
Press UNLOCK on the OEM
remote.
UNLOCK
9
Wait, LED will turn solid GREEN
4
LED will turn solid RED. for 2 seconds.
10
Module Programming
5
Within 5 seconds, LED will flash Procedure completed.
GREEN rapidly.
MODULE PROGRAMMING
INSTALLATION
PROCEDURE
MODE SELECTION
- PUSH TO START
1 2
5
Æ
Close driver
Press and release
door. DO NOT
Press andPRESS
hold BRAKE PEDAL
programming button
to select installation mode. x1 programming button
until
PushLED
startturns solid
button GREEN
once [1x] to
to register
OFF selection.
position.
6 !
LED flashes (1X) once = DATA Re-open
MODE driver door to wake up Press UNLOCK
After registration, follow Factory on the OEM
Reset Procedure to
data bus.
LED flashes (2X) twice = STANDARD HARDWIRE MODE change installation mode andremote.
restart this procedure.
UNLOCK
2
Æ
DO NOT PRESS BRAKE PEDAL
3 7
LED will turn solid RED. Wait, LED will turn solid GREEN
for 2 seconds.
4 8
Within 5 seconds, LED will flash Module Programming
GREEN rapidly. Procedure completed.
Æ
F 1985 S 1995 5 2005 F 2015
G 1986 T 1996 6 2006 G 2016
43A5Y1N5TAL8D5R0X
H 1987 V 1997 7 2007 H 2017
J 1988 W 1998 8 2008 J 2018
K 1989 X 1999 9 2009 K 2019
MODULE DIAGNOSTICS
DIAGNOSTICS
LED STATUS
DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF
Missing/wrong information from
Flashing RED Incorrectly programmed Incorrectly programmed or connected
firmware or vehicle
Not programmed waiting for more
Solid RED Waiting for more vehicle information Incorrectly programmed
vehicle information
Additional steps required to complete Correctly programmed and False ground when running status
Flashing GREEN
programming operational from remote starter
Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress
Invalid ground when running status At rest and ready for a remote start
OFF No activity or already programmed
from remote starter sequence
1 5
DISCONNECT all connectors LED will turn solid red for 2
6
RECONNECT all connectors.
2
DISCONNECT black 4-PIN
standard or optional data
connector.
7
Repeat programming procedure.
3
PRESS AND HOLD programming
button while connecting either
!
4-PIN standard or optional data
connector. Failure to follow procedure may result with a DTC or a
CHECK ENGINE error message.
4
When LED flashes red,
RELEASE programming button.
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
NOTE
3
Insert key into ignition.
4
Turn key to ON position.
TIME RESTRICTIºN COMING UP !
È ON Wait 2 seconds for key
validation.
5
Press and release BRAKE pedal.
1
Press UNLOCK on after-market
remote.
2 TIME RESTRICTIºN
Within 45 SECONDS from 6
Take over procedure completed.
previous step:
!
Failure to follow procedure within time restriction will
Open vehicle door. result in vehicle engine shutdown.
Enter vehicle.
3
Æ
NOTE DO NOT PRESS BRAKE PEDAL
1
Press UNLOCK on after-market
remote.
5
Take over procedure completed.
2 TIME RESTRICTIºN
!
Within 45 SECONDS from Failure to follow procedure within time restriction will
previous step: result in vehicle engine shutdown.