Professional Documents
Culture Documents
1
Contents:
General information 3
Machine description B10 ELECTRA 3
Identification data 4
Tests 4
Warranties 5
Safety regulations 5
Technical specifications 6
Accessories 7
Machine equipment 7
Control elements B10 ELECTRA 8
Use 9
Setting the removal size 9
Bevelling 11
Bevel angle and shape change. 12
Milling head replacement 12
Replacement of indexable inserts 13
Maintenance and operation 14
Spare parts 14
List of spare parts 15
2
1. General information
Thank you for purchasing one of our machines, and we hope that you will be fully satisfied.
This guide provides instructions for the installation, adjustment, operation and
maintenance of the machine B10 ELECTRA in compliance with valid safety standards.
The information and data contained in this document subject to changes due to
further improvement of machinery. To eliminate any doubts, when differences are
detected, please contact N.KO Machines.
Never perform any operation on the machine before you read the instructions in the
manual and understand them. Major part of accidents that happen in the workplace are
due to the fact that the guidelines and recommendations contained in the manual are
not complied with.
The graphic symbols used in the manual are intended to emphasize the important
information regarding the safety and operation of the machine.
Attention :
Information important for the personal safety of the operating staff.
Important:
Instruction that needs to be observed to ensure the proper function of the machine.
3
3. Identification data and CE Declaration of Conformity
The identification data of machine B10 ELECTRA are listed on the label placed on the drive unit.
4
4. Tests
5. Warranties
The B10 ELECTRA is provided by the seller with a guarantee that the article shall not
feature any material and production defects for a period of 12 months following the
delivery date.
The machine is provided with a 12-months' guarantee from the delivery date for the faultless
function of the article and the materials used.
The seller undertakes to make sure that any potential warranty defects are removed free of
charge and without undue delay so that the buyer is able to use the article the way they desire.
Should the buyer claim liability for warranty-unrelated defects, it shall reimburse the seller for
any expenses associated with that.
6. Safety regulations
5
Attention :
In order to prevent the injury observe the below instructions
Inspect the machine for mechanical and other damage prior to bevelling.
Commission the machine solely if the electricity supply cable is not damaged.
Check the supply cord regularly. In case of damage have it replaced in an authorised
service shop authorised to perform the such repairs. Contact your supplier.
Connect the machine in electrical network solely if the machine is in off position.
Prior to each use, check the device and electricity supply cord for damage. Do not
use the machine in case of any damage.
Do not use the machine in humid environment and protect from high moisture.
Ensure good lighting at the workplace to prevent the risk of potential injury or
eyesight damage.
Caution, the tool (milling machine) is sharp with the risk of injury. During the
replacement use safety gloves, never touch the miller which moves.
The machined material must always be fastened and horizontal. Optimum
workpiece height is 900 mm above ground.
During work pay attention to the electricity supply cable; it should be loosely placed on
the ground outside the worked material and other sharp objects.
After work, disconnect equipment from the electricity supply.
Do not overload the machine motor. The machine operates better if not overloaded.
During work, hold the device by both hands.
Attention is drawn to the injury hazard with hot metal shavings.
Important:
In case of damage have the machine repaired in an authorised service shop authorised
to perform the repairs. For more information on, contact your supplier.
7. Technical specifications
6
Bevel angle Replacement head 30°, 37,5°, 45°, 50°,
60° other angles upon request
Bevel width (45°) 0 to 10 mm / 0 to 0,4 in< 400N/mm2/ 58 015 PSI - 0
to 5 mm > 400N/mm2/ 58 015 PSI
Rounding max R 4 mm / 0,16 in
Motor electric
Motor power 1700W/50Hz, 1500W/60Hz
Revolutions 2700 - 8500 rpm
Weight 6 kg/ 13,2 lb.
Number of indexable inserts 6 pcs (milling head for rounding edges 3pcs)
8. Accessories
Milling head 30° (incl. inserts, screws, bolts, and roller) 27 223
Milling head 37.5° (incl. inserts, screws, bolts, and roller) 27 227
Milling head 45° (incl. inserts, screws, bolts, and roller) 27 222
Milling head 50° (incl. inserts, screws, bolts, and roller) 27 224
Milling head 60° (incl. inserts, screws, bolts, and roller) 27 240
Coated inserts, 4-bit for 30°/37,5°/ 45°/50°/ 60° (package 10pcs) 27 231
Screw for attaching the bevelling inserts 27 241
Milling head for rounding 2.5mm / 0,08 in (incl. inserts, screws, bolts, 27 234
and roller)
Milling head for rounding R 3.5 and 4 mm / 0,12 in, 0,16 in (incl. 27 233
inserts, screws, bolts, and roller)
Coated inserts, 4-bit for R 2,5 mm / 0,08 in (package 10pcs) 26 109
Coated inserts, 4-bit for R 3.5 mm / 0,12 in (package 10pcs) 26 110
Coated inserts, 4-bit for R 4 mm / 0,16 in (package 10pcs) 26 111
7
9. Machine equipment
Unpack the machine from the cardboard box and check if the machine is ok and
free from damage. If necessary contact the seller.
Machine B10 ELECTRA is supplied with required tools for the operation
without the tool.
Purchase the tools. The review of tools is defined in chapter 8. Accessories or in the catalogue
of N.KO Machines and contact your supplier.
Fig.10.0.1
A. Handle
B. Motor body
C. Scale for reading the bevel size setting
D. The miller unit with indexable inserts
E. Guiding, stop miller roller and roller screw
F. The arresting screws of the thrust place sleeve – The set removal provision
G. The thrust plate with sleeve
H. Main switch
8
11. Use
Important:
The device can be used solely if it is fitted with the original indexable inserts supplied by
our supplier, i.e. the device manufacturer. It includes four-sided indexable inserts. The
device can be fitted with 6 pieces of indexable inserts. It is prohibited to use other than
original inserts.
Attention :
During the adjustment operation, wear gloves and other personal protective
equipment. The operations must be carried out on the machine at rest and after
disconnecting from the power supply.
Important:
Maximum reduction is 10mm of bevel width (dimension P fig.11.1.1). The reduction can be
achieved in more steps. It depends on the material solidity. We recommend performing the
test.
Start with lower reduction and gradually increase the value until the work with the machine is
comfortable and the plates can achieve gradually reduction without increased vibrations. For
orientation setting, use the tables below.
We recommend administering the work log for recording the measured value and the
machining procedure.
9
Fig. 11.1.1
For orientation setting of the reduction size and the independent machining process, use
the setting tables for individual bevel angles.
Important:
The values in the table are calculated from point 0. Point is the point when the
miller touches the material edge for the first time. This point can be set by
gradual turning of the thrust plate (fig.10.0.1 position G) and placing to the
material edge.
45° - For full bevel (P=10mm) is required, turn the thrust plate by 40 revolutions
Chip no. Hypotenuse P Bevel height A Number of rpm of the
thrust plate
(Fig.10.0.1 pos. G)
I. 5mm/0,19 in 3.5mm/0,13 in 2 Revolutions
II. 10mm/0,39 in 7.7mm/0,30 in + 2 Revolutions
10
Important:
The machine was constructed for the preparation of welded surfaces. Machining
accuracy is within limit
+/-1mm. The condition for reaching the satisfactory results is a perfect
preparation of the material edges. Unfortunately the material is often burned or
cut. The inaccuracy shall be reflected on the resulting machining.
Important:
If it is difficult to machine the bevel within the recommended number of steps,
we recommend dividing the process to more chips. The reason can be the wear of
the cutting inserts or worse machining properties of material.
11.2 Bevelling
Attention :
During work, wear gloves and other personal protective equipment.
The maintenance operations must be carried out on the machine at rest and after
disconnecting from the power supply.
Important:
The shift during machining is always from left to the right.
11
Attention :
The device operators must hold the device with both hands.
Machine B10 ELECTRA is constructed for the use of more milling heads, see chapter
8. Accessories.
Fig. 11.3.1
12
Fig. 11.3.2
Fig. 11.3.3
13
Attention :
During the adjustment operation, wear gloves and other personal protective
equipment. The operations must be carried out on the machine at rest and
after disconnecting from the power supply.
Important:
Work solely with sharp and not damaged indexable inserts. It prevents the
machine damage. If the cutting inserts are worn or damaged or cracked,
they must be replaced.
Attach the wrench (fig. 11.3.1 position D) release the screws used for fastening
the indexable inserts (fig. 11.3.1 position C)
Indexable inserts (fig. 11.3.1 position B) replace with new, different, or just turn
them to use all cutting edges.. Attention! Considering the specific shape, focus on
this operation.
Indexable inserts must be appropriately fastened (fig. 11.3.1 position C).
Assemble the guiding plate set according to chapter 11.3
Fig. 11.4.1
14
12. Maintenance and operation
Maintenance of machine B10 ELECTRA does not require any special tools and it is
very simple. Keep the machine clean and replace the lubrication grease in the
machine gearbox every 1000 working hours. This operation must be performed solely
in authorised service N.KO Machines.
Regularly check the supply power cable. In case of damage have it replaced in an
authorised service shop authorised to perform the such repairs. Contact your supplier.
Important:
The moving parts, threads, and mechanical connections must be gradually
cleaned using compressed, and must be preserved (greased).
Attention :
When using compressed air for cleaning, wear safety goggles and never use a
pressure exceeding 2 bar.
machine type;
serial number;
Description of required part and its number
quantity.
15
16
17
18
A copy of this manual is supplied with every
machine B10 ELECTRA
All rights reserved.
No part of this publication may be reproduced without the previous consent granted by the company
N.KO.
19