Professional Documents
Culture Documents
Page 1 of 5
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AMC
Configuration: 320C & 320C L Excavators AMC00001-UP (MACHINE)
POWERED BY 3066 Engine
Specifications
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5545-12 Publication Date -01/07/2006 Date Updated -12/07/2006
i01779832
Camshaft
SMCS - 1210
Illustration 1 g00527937
Maximum permissible temperature of the gear for installation on the camshaft ... 315°C (600°F)
NOTICE
Do not use a torch to heat the gear. A torch can unevenly heat the gear
causing warpage. The hardness of the gear may also be changed with
the use of a torch.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/11/2007
320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 2 of 5
(2) Diameters of camshaft journals
Table 1
Illustration 2 g00527952
Service limit for lobe lift for exhaust ... 6.844 mm (0.2695 inch)
Service limit for lobe lift for inlet ... 6.189 mm (0.2437 inch)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/11/2007
320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 3 of 5
Note: Replace the camshaft if the service limit for the lobe lift is reached.
3. Subtract the base circle that is found in Step 2 from the lobe height that is found in Step 1. The
difference is the actual camshaft lobe lift (4) .
Illustration 3 g00528061
Note: Use a dial indicator and blocks in order to determine the runout of the camshaft. Take one half of the
dial indicator reading as the runout.
(7) Camshaft
Straighten the camshaft if runout is less than the following amount. ... 0.050 mm (0.0020 inch)
Replace the camshaft if runout is more than the following amount. ... 0.050 mm (0.0020 inch)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/11/2007
320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 4 of 5
Illustration 4 g00528067
Measure the camshaft bearing with a dial indicator. Subtract the diameter of the camshaft journal in order to
give bearing clearances. Refer to Table 2.
Table 2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/11/2007
320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine(SEB... Page 5 of 5
Illustration 5 g00529304
(9) Install the dial indicator in order to determine gear end play.
Replace the thrust plate if the end play exceeds the following amount. ... 0.30 mm (0.012 inch)
Copyright 1993 - 2007 Caterpillar Inc. Wed Apr 11 13:42:57 UTC+0630 2007
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/med... 4/11/2007