Professional Documents
Culture Documents
1. This register shows cylinder standards that may be used for newly manufactured cylinders. A cylinder can only
be manufactured or imported into New Zealand if it is designed to a standard that appears on this list.
General Register Notes
2. Where a cylinder standard has been withdrawn by the respective standards authority the standard should not
appear on this list. If you are aware of an anomaly, please contact WorkSafe NZ.
DOT-SP 10915 Fully wrapped carbon-fibre reinforced aluminium lined US Department of Transportation permit expires 30 November
cylinders conforming to DOT CFFC 2009
DOT-SP 10945 Fully wrapped carbon fibre reinforced aluminium lined US Department of Transportation permit expires 28 February
cylinders based on DOT CFFC 2010
DOT-SP 11953 Welded steel cylinder based on DOT 4BW for non-liquefied US Department of Transportation permit expires 30
and liquefied compressed gases September 2009
British
Transportable gas containers. Specification for steel
BS 5045-2:1989 containers of 0.5 L up to 450 L water capacity with welded Partially replaced by BS EN 13322-1:2003
seams
Transportable gas containers. Specification for seamless steel
BS 5045-7:2000 gas containers of water capacity 0.5 L up to 15 L for special Together with BS EN 1964-1:2000 supersedes BS 5045-
portable application 1:1982.
Transportable gas containers. Specification for seamless
aluminium alloy gas containers of water capacity 0.5 L up to
BS 5045-8:2000 Replaces BS 5045-3:1984
15 L and up to 300 bar charged pressure at 15°C for special
portable application
Transportable gas cylinders. Specification for the design and
construction of refillable transportable seamless steel gas
BS EN 1964-1:2000 cylinders of water capacities from 0,5 litre up to and including Replaces withdrawn standard BS 5045-1:1982
150 litres. Cylinders made of seamless steel with a value of
less than 1100 MPa
BS EN 1964-2:2001 Transportable gas cylinders. Specification for the design and
construction of refillable transportable seamless steel gas
cylinders of water capacities from 0,5 litre up to and including
150 litres. Cylinders made of seamless steel with a value of
1100 MPa and above
BS EN 1975:2000
Transportable gas cylinders. Specification for the design and
construction of refillable transportable seamless aluminium
and aluminium alloy gas cylinders of capacity from 0,5 litre up
to 150 litre
BS EN 12862:2000 Transportable gas cylinders. Specification for the design and
construction of refillable transportable welded aluminium alloy
gas cylinders
EN
EN 3 Portable Fire Extinguishers
This standard must be used in accordance with the ERMA
EN 12245 (as amended
Fully Wrapped Composite Cylinders approved Gas Cylinders of Composite Construction Designed
by ERMA COP)
to EN 12245:2009
EN 13110 - 2002 Welded Aluminium LPG Cylinders
Seamless unalloyed aluminium and aluminium alloy gas
84/526/EEC
cylinders with capacity between 0.5 to 150 litres
ISO
Cylinders of seamless steel of tensile strength less than
ISO 9809-1:1999 0.5 litre up to and including 150 litres
1100Mpa
Cylinders of seamless steel of tensile strength greater than or
ISO 9809-2:2000 0.5 litre up to and including 150 litres
equal to 1100Mpa
ISO 11119-1 (As
Gas Cylinders of composite construction – Specification and This standard must be used in accordance with the ERMA
amended by ERMA
test methods – Part 1: Hoop wrapped composite gas approved Code of Practice for Gas Cylinders of Composite
approved code of
cylinders. Construction Designed to ISO 11119-1
practice)