Professional Documents
Culture Documents
v01.1002 HMC434
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
Reverse Leakage RF Output Terminated, Fin= 4 GHz, Pin= 0 dBm -20 dBm
SSB Phase Noise (100 kHz offset) Pin= 0 dBm, Fin= 4 GHz -150 dBc/Hz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
10 - 84
Order Online at www.hittite.com
MICROWAVE CORPORATION
v01.1002 HMC434
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
InputGaAs MMIC
Sensitivity SUB-HARMONICALLY
Window, T= 25 °C PUMPED
Input MIXER
Sensitivity Window17 - 25 GHz
vs. Temperature
20 20
15 15
10 10
INPUT POWER (dBm)
10
Max Pin -40 C
0
Operating Window 0
Min Pin +85 C
Max Pin +85 C
-5 -5
-10 -10
-20 -20
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz)
-20
SSB PHASE NOISE (dBc/Hz)
-1
-40
OUTPUT POWER (dBm)
-60
-2
-80
-3
-100
+25 C
-40 C -120
-4 +75 C
-140
-5 -160
2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 10 10 10 10 10 10
INPUT FREQUENCY (GHz) OFFSET FREQUENCY (Hz)
Output Harmonic
Content, Pin= 0 dBm, T= 25 °C Reverse Leakage, Pin= 0 dBm, T= 25 °C
0 0
-10
-10
OUTPUT LEVEL (dBm)
-20
-20
-30
-30
-40
-40 Pfeedthru
2nd Harmonic -50
3rd Harmonic
-50 -60
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 10 - 85
Order Online at www.hittite.com
v01.1002 HMC434
MICROWAVE CORPORATION
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
Output Voltage Waveform,
Pin= 0 dBm, Fout= 882 MHz, T= 25 °C Absolute Maximum Ratings
300 RF Input (Vcc= +3.0V) +15 dBm
250
Vcc +3.5V
200
150 Maximum Channel Temperature 135 °C
AMPLITUDE (mV)
100
50 Continuous Pdiss (T=85 °C)
10 0
-50
-100
(derate 5.35mW/°C above 85 °C)
Storage Temperature
268 mW
-65 to +150 °C
-200
DC blocking capacitors are required at RF input and RF output ports.
-250 Choose value for lowest frequency of operation.
-300
22.7 22.9 23.1 23.3 23.5 23.7 23.9 24.1 24.3 24.5 24.7
TIME (nS)
Typical Supply Current vs. Vcc
Vcc (V) Icc (mA)
2.70 50
3.0 62
3.30 74
Note: Divider will operate over full voltage range shown above
Outline Drawing
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEADFRAME MATERIAL: COPPER ALLOY
3. LEADFRAME PLATING: Sn/Pb SOLDER
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
10 - 86
Order Online at www.hittite.com
MICROWAVE CORPORATION
v01.1002 HMC434
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
Pin Description
Pin Number Function Description Interface Schematic
1, 4 N/C No Connection
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 10 - 87
Order Online at www.hittite.com
v01.1002 HMC434
MICROWAVE CORPORATION
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
Evaluation PCB
10
FREQ. DIVIDER & DETECTORS - SMT
List of Materials
The circuit board used in the final application should
Item Description
use RF circuit design techniques. Signal lines should
J1 - J2 PC Mount SMA RF Connector have 50 ohm impedance while the package ground
J3 - J4 DC Pin leads should be connected directly to the ground
plane similar to that shown. A sufficient number of via
C1 - C2 100 pF Capacitor, 0402 Pkg.
holes should be used to connect the top and bottom
C3 1000 pF Capacitor, 0402 Pkg. ground planes. The evaluation circuit board shown is
C4 10 µF Tantalum Capacitor, 1206 Pkg.
available from Hittite upon request.
U1 HMC434 Divide-by-8
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
10 - 88
Order Online at www.hittite.com
v01.1002 HMC434
MICROWAVE CORPORATION
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 8.0 GHz
Application Circuit
10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 10 - 89
Order Online at www.hittite.com
This datasheet has been download from:
www.datasheetcatalog.com