Professional Documents
Culture Documents
Number of Antennas 8 Tx
DL Bandwidth 20 MHz
12 RB
Output
Prs 15.4 dBm
Pa -3 dB
Pb 1
Note:
Number of antennas: Indicates the number of transmit antennas, such as 2T, 4T, or 8T.
Number of ports: Indicates the number of antenna ports. In the FDD system, the number of
antennas is equal to the number of ports. In the TDD system, if beamforming is used, the 4T
and 8T antennas can be mapped to two or four antennas ports. Therefore, the number of
antennas is greater than the number of ports.
DL bandwidth: Indicates the bandwidth on the downlink and the number of RBs.
Maximum transmit power of a single antenna: Indicates the maximum transmit power of eac
antenna. For example, 4 x 2.5 W indicates that there are four antennas and the maximum
transmit power of each antenna is 2.5 W.
Note:
If the output values of the Pa and Pb parameters are FALSE, the input parameters are
incorrect.
Do not click Save before exiting this tool. Otherwise, the formula in the sheet may be change
Note:
number of RBs.
mum transmit power of each
nnas and the maximum
SriPeriod
(The value varies with different
subframe configurations.)
DRX
(The value varies with different
subframe configurations.)
HoppingOffset
(The value varies with different
bandwidths or subframe
configurations.)
SriLowLoadThd
(The value varies with different
subframe configurations.)
SriLowLoadThd
(The value varies with different
subframe configurations.)
PcfichPwr
(The parameter indicates the channel
transmit power and its value varies with
different bandwidths.)
PwrOffset
(Indicates the power offset between the
PHICH TX power and the RS power.
This offset is used when PHICH power
control is disabled.)
EDlMaxTXPwrSwitch(Indicates the
switch for enhanced maximum TX
power of the cell)
AbsPattern
UlEnhancedFssSwitch(Indicates
whether to enable the uplink load-based
frequency selection enhancement.This
switch is valid only in FDD mode)
InterRatHoUtranB1Hyst(UTRAN
handover hysteresis)
InterRatHoUtranB1TimeToTrig(UT
RAN time to trigger)
UlVoipRlcMaxSegNum(Ulplink Voip
Rlc Maximum Segmentation Number)
PucchSwitch(PUCCH algorithm
switch)
NaSriChNum(ACK/SRI Channel
Number)
CqiRbNum(CQI RB number)
NaSriChNum(ACK/SRI Channel
Number)
CqiRbNum(CQI RB number)
NaSriChNum(ACK/SRI Channel
Number)
CqiRbNum(CQI RB number)
SriPeriod(SRI Period)
BbResExclusiveSwitch(Baseband
Equipment Exclusive Switch)
PrachFreqOffset (PRACH Frequency
Offset)
ENodeBUmReorderingTimer (UM
reordering timer for eNodeB)
DlSchAbnUeThd(Downlink Schedule
Abnormal Ue Threshold)
Format1ChAllocMode (Format1
Channel Allocation Mode)
TimeAlignmentTimer(Uplink time
alignment timer)
PdcchBlerTarget(PDCCH BLER
Target)
PdcchOutLoopAdjLowerLimit(PDC
CH Outloop adjust lower limit)
1. This document provides TDD baseline parameter configurations different from that in FDD mode. The configuration mu
configuration.
2. For common baseline parameters in TDD or FDD mode, visit \Software\01 eNodeb\02 inner doc\03 baseline paramete
3. The default value of the ReferenceSignalPwr parameter is 182 in FDD mode. This value must be changed in TDD mode
based on specifications of the maximum power and network plan.
For details about the configuration tool, see the LTE Downlink Power Control Parameter Configuration Tool V1.2 sheet.
ters in TDD Mode Different from that in FDD Mode Based on the Subframe Configurati
When the subframe configuration is 0 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF2, DrxInactivityTimerSpecial=PSF3;
When the subframe configuration is 2 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF3, DrxInactivityTimerSpecial=PSF4;
When the subframe configuration is 3 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF2, DrxInactivityTimerSpecial=PSF3;
When the subframe configuration is 4 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF3, DrxInactivityTimerSpecial=PSF4;
When the subframe configuration is 5 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF3, DrxInactivityTimerSpecial=PSF4;
When the subframe configuration is 6 (QCI 1/5, QCI 4/7, and QCI 6/8/9 correspond to values 1, 2, and 3 of DrxParaGrou
follows:
MOD DRX: DrxAlgSwitch=OFF, OnDurationTimerSpecial=PSF2, DrxInactivityTimerSpecial=PSF3;
When the bandwidth is 5 MHz and subframe configuration is 1, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 9;
When the bandwidth is 5 MHz and subframe configuration is 2, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 10;
When the bandwidth is 5 MHz and subframe configuration is 5, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 10;
When the bandwidth is 10 MHz and subframe configuration is 0, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 13;
When the bandwidth is 10 MHz and subframe configuration is 1, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 16;
When the bandwidth is 10 MHz and subframe configuration is 2, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 22;
When the bandwidth is 10 MHz and subframe configuration is 5, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 19;
When the bandwidth is 15 MHz and subframe configuration is 0, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 13;
When the bandwidth is 15 MHz and subframe configuration is 1, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 16;
When the bandwidth is 15 MHz and subframe configuration is 2, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 22;
When the bandwidth is 15 MHz and subframe configuration is 5, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 19;
When the bandwidth is 20 MHz and subframe configuration is 0, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 20;
When the bandwidth is 20 MHz and subframe configuration is 1, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 26;
When the bandwidth is 20 MHz and subframe configuration is 2, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 26;
When the bandwidth is 20 MHz and subframe configuration is 5, the configuration is as follows:
MOD PUSCHCFG: LocalCellId = 0, HoppingOffset = 26;
When the bandwidth is 5 MHz and the single-channel transmit power is 10 W, the configuration is as follows:
MOD PDSCHCFG: LocalCellId=0, ReferenceSignalPwr=182;
When the bandwidth is 10 MHz and the single-channel transmit power is 10 W, the configuration is as follows:
MOD PDSCHCFG: LocalCellId=0, ReferenceSignalPwr=152;
When the bandwidth is 20 MHz and the single-channel transmit power is 10 W, the configuration is as follows:
MOD PDSCHCFG: LocalCellId=0, ReferenceSignalPwr=122;
TDD:
MOD SRSCFG: LocalCellId=0, SrsSubframeCfg=SC0;
TDD:
MOD CELLPDCCHALGO: LocalCellId=0, InitPdcchSymNum=3, PdcchSymNumSwitch=OFF;
For Bandwidth=10M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=13, CqiRbNum=2;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=16, CqiRbNum=2;
For Bandwidth=20M
TDD subframe configuration 1 and 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=52, CqiRbNum=3; /// Same configuration for both subframe configura
High speed Scenario - for eRAN8.1 version
For Bandwidth=10M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=22, CqiRbNum=2;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=44, CqiRbNum=3;
For Bandwidth=20M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=38, CqiRbNum=3;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=75, CqiRbNum=6;
For Bandwidth=10M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=44, CqiRbNum=2;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=88, CqiRbNum=3;
For Bandwidth=15M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=62, CqiRbNum=2;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=122, CqiRbNum=4;
For Bandwidth=20M
TDD subframe configuration 1:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=76, CqiRbNum=3;
TDD subframe configuration 2:
MOD PUCCHCFG: LocalCellId=0, NaSriChNum=150, CqiRbNum=6;
MOD CELLPDCCHALGO:LocalCellId=0,PdcchBlerTarget=5;
MOD CELLPDCCHALGO:LocalCellId=0,PdcchOutLoopAdjLowerLimit=-2;
Date Version
5/19/2011 V1.0
6/22/2011 V1.1
10/26/2012 v1.5
12/13/2012 v1.6
1/24/2013 v1.7
4/11/2013 V1.8
4/15/2013 V1.9
5/17/2013 V2.0
7/2/2013 V2.1
7/16/2013 V2.2
10/28/2013 V2.3
11/22/2013 V2.4
3/20/2014 V2.5
4/10/2014 V2.6
5/21/2014 V2.7
6/18/2014 V2.8
9/5/2014 V2.9
9/11/2014 V3.0
12/3/2014 V3.1
3/3/2015 V3.2
7/29/2015 V3.3
8/13/2015 V3.4
2015/12/31 V3.5
1/29/2016 V3.6
6/24/2016 V3.7
8/24/2016 V3.8
Description