Professional Documents
Culture Documents
板卡類型
NTIO 上聯板,支持 8 光口 GE 上聯
CT 設置
“9600bps with 8 data bit, no parity, one stop bit and flow control set to none”配置說明
紅字部分為根據實際情況需要修改的部分
一、開局配置部分
1.設備登錄
Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]: c
login: isadmin
password:i$@mad-
2.創建板卡(主控板、上聯板、PON 板需創建)
configure equipment slot nt-a planned-type fant-f
configure equipment slot nt-b planned-type fant-f
configure equipment protection-group 1 admin-status unlock configure system security
profile admin slot-numbering type-based configure system port-num-in-proto type-based
configure system max-lt-link-speed link-speed ten-gb
admin save
admin equipment reboot-isam with-self-test
configure equipment slot lt:1/1/4 planned-type fplt-a unlock configure interface port
epon:1/1/1/2 admin-up
3.打開上聯埠(以下,埠均列出)
configure port nt-a:xfp:1 ethernet no autonegotiate
configure port nt-a:xfp:1 ethernet speed 1000
configure port nt-a:xfp:1 no shutdown
configure port nt-a:xfp:2 ethernet no autonegotiate
configure port nt-a:xfp:2 ethernet speed 1000
configure port nt-a:xfp:2 no shutdown
configure port nt-a:xfp:3 ethernet no autonegotiate
configure port nt-a:xfp:3 ethernet speed 1000
configure port nt-a:xfp:3 no shutdown
configure port nt-a:xfp:4 ethernet no autonegotiate
configure port nt-a:xfp:4 ethernet speed 1000
configure port nt-a:xfp:4 no shutdown
configure port nt-a:eth:1 ethernet no autonegotiate
configure port nt-a:eth:1 ethernet speed 1000
configure port nt-a:eth:1 no shutdown
configure port nt-b:xfp:1 ethernet no autonegotiate
configure port nt-b:xfp:1 ethernet speed 1000
configure port nt-b:xfp:1 no shutdown
configure port nt-b:xfp:2 ethernet no autonegotiate
configure port nt-b:xfp:2 ethernet speed 1000
configure port nt-b:xfp:2 no shutdown 系統提示資訊(C 命令)
缺省用戶名
缺省密碼
創建主控板 NTA
創建主控板 NTB
打開主控板主備倒換
配置子框類型
重啟(該步驟必須)
創建 PON 板(LT 板)
開啟 PON 口
設置管理位址和管理 vlan
configure router static-route 0.0.0.0/0 next-hop 10.10.32.1 configure service ies 2
customer 1 create
configure service ies 2 interface "OAM" create
configure service ies 2 interface "OAM" address 10.10.32.5/24 configure service ies 2
interface "OAM" sap nt:vp:1:999 create configure service ies 2 no shutdown
configure service vpls 3 customer 1 v-vpls vlan 999 create configure service vpls 3 sap
nt-a:xfp:1:999 create
configure service vpls 3 no shutdown
打開 SNMP 網管管理功能
configure system security snmp community public host-address 0.0.0.0/0 context nt
privilege read-write
configure system security snmp community ihub host-address 0.0.0.0/0 context ihub
privilege read-write
5.配置上聯業務
configure vlan id 3410 mode residential-bridge
業務 vlan 透傳到上聯板、上聯口、PON 板
configure service vpls 3410 customer 1 v-vpls vlan 3410 create configure service vpls
3410 sap nt-a:xfp:1:3410 create
configure service vpls 3410 sap lt:1/1/1:3410 create
configure service vpls 3410 no shutdown
6.配置引用範本
configure qos profiles bandwidth up_100excessive-info-rate 100000 committed-info-rate
0 assured-info-rate 0 delay-tolerance 20NTB 上聯電口 1 強制
NTB 上聯電口 1 速率
NTB 上聯電口 1 啟用
設置管理閘道
設置管理位址和子網路遮罩
啟用管理配置
打開 MIB1
打開 MIB2
1.創建 onu
configure equipment eont interface 1/1/1/1/2 mac-addr new-mac configure equipment
eont interface 1/1/1/1/2 admin-state up
2.該 ONU 的 ELLID 和 bridge port
configure interface port ellid:1/1/1/1/2/1 admin-up
configure qos interface ellid:1/1/1/1/2/1 upstream-queue 255 bandwidth-profile
name:up_100
configure bridge port 1/1/1/1/2/1 max-unicast-mac 64
configure bridge port 1/1/1/1/2/1 vlan-id 3410
3.埠 vlan、mac 位址、啟動 ETH 埠
configure equipment eont interface 1/1/1/1/2 port 1/1
configure equipment eont interface 1/1/1/1/2 port 1/1vlanmode tagged vlanid-default
3410
configure equipment eont interface 1/1/1/1/2 port 1/1 mac-max 4 configure interface port
euni:1/1/1/1/2/1/1 admin-up
三、更換 ONU
configure equipment eont interface 1/1/1/1/2 admin-state down configure equipment eont
interface 1/1/1/1/2 mac-addr new-mac configure equipment eont interface 1/1/1/1/2
admin-state up 根據 MAC 位址創建 ONU 格式:AA:BB:CC:DD:EE:FF <架/框/板/口/ONU
ONU 的 ELLID 恒為 1
<架/框/板/口/ONU/ETH 口
關閉原 ONU
<架/框/板/口/ONU
四、一般配置命令
1.查看系統軟體版本
show software-mngt oswp
2.查看 OLT 主控板上聯光口 1 的光功率指標 show equipment diagnostics sfp nt-a:xfp:1
detail
3.查看 OLT PON 口的發送光功率指標
show epon optics 1/1/1/1 detail
4.查看 OLT PON 口收光及 ONU PON 口的收發光功率指標 show equipment eont optics
1/1/1/1/2 detail
5.查看主控板溫度及狀態
debug-command temperature na-a
6.查看 PON 板溫度及狀態
debug-command temperature lt:1/1/2
架/框/板
RTRV-ALM-ALL; <架/框/板/口
<架/框/板/口/ONU <架/框/板
<架/框/板
<架/框/板/口/ONU T 命令模式下