Professional Documents
Culture Documents
AVS9706030A8
Combination Camera
WV-CS600A/WV-CS604E/WV-CST600
fi ed
pli
Sim
Please file and use this manual together with the service manual for the Model No.
WV-CSR600, order NO. AVS9703018C8.
SPECIFICATIONS
Combination Camera
Power Source : 230 V AC, 50Hz for WV-CS600A/WV-CST600, 24V AC, 50 Hz for WV-CS604E
Power Consumption : 16W
Ambient Operating Temperature : –10°C - +50°C
Dimensions : 130 (D) x 191 (H) mm for WV-CS600A/WV-CS604E
130 (D) x 195 (H) mm for WV-CST600
Weight : Approx. 2 kg
Camera
Pick-up Device : 1/3” CCD with 752 (H) x 582 (V) pixels for WV-CS600A/WV-CS604E
1/4” CCD with 752 (H) x 582 (V) pixels for WV-CST600
Synchronization : Internal/Line-lock/Multiplexed/Vertical Drive (VD2)
Horizontal Scanning Frequency : 15.625 KHz
Vertical Scanning Frequency : 50 Hz
Video Output : 1.0 V[p-p] PAL composite/75 Ω
Horizontal Resolution : More than 480 lines at centre
Vertical Resolution : More than 400 lines at centre
Signal-to-noise Ratio : 48 dB (AGC OFF, weight on)
Minimum Illumination : 3 lx (0.3 footcandle) for WV-CS600A/WV-CS604E
6 lx (0.6 footcandle) for WV-CST600
Zoom Speed : Approx. 6 s (TELE/ WIDE) in Manual mode
Focus Speed : Approx. 5 s (FAR/NEAR) in Manual mode
Iris : Automatic (Open / Close is possible)/Manual
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER This symbol alerts the user that impotant literature concerning
SERVICEABLE PARTS INSIDE. the operation and maintenance of this has been included.
REFER SERVICING TO QUALIFIED SERVICE Therefore, it should be read carefully in order to avoid
PERSONNEL. any problems.
There are special components used in this equipment which are important for safety. These parts are indicated
by the ” Y ” mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
Pan / Tilt
Panning Range : 360° Endless
Panning Angle Setting : Possible (in Auto-Pan mode)
Panning mode : Manual/Sequential Position/Sort Position/Auto Pan
Panning Speed : Manual : Approx. 3°/s - 120°/s eight steps
Sequence Position : Maximum approx. 240°/s
Tilting Range : 0 - 90°
Tilting Mode : Manual/Sequential Position/Sort Position
Tilting Speed : Manual : Approx. 1.5°/s - 60°/s. eight steps
Sequential Position : Maximum approx. 120°/s
Controls : Pan/Tilt, Lens, 64 Preset Positions, Home Position
ACCESSORIES
Camera Mounting Angle . . . . . . . . . . . . . . . . . 1 pc.
Camera Fixing Screw . . . . . . . . . . . . . . . . . . . 1 pc.
Connector (for WV-CS604E) . . . . . . . . . . . . . . 1 pc.
Decoration Cover . . . . . . . . . . . . . . . . . . . . . . 1 pc.
OPTIONAL ACCESSORIES
Dome Cover (Smoked type) . . . . . . . . . . . . . . WV-CS1S
Ceiling Mount Bracket . . . . . . . . . . . . . . . . . . . WV-Q105E/WV-Q106E/WV-Q107E
Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . WV-Q108E
CONTENTS
Construction ............................................................................................................................................ 1
Installation................................................................................................................................................ 2
Connection ............................................................................................................................................... 5
System Connection ................................................................................................................................. 6
Schematic Diagram
Sensor Board (WV-CST600/G) .............................................................................................................. 7
Power Board (WV-CST600/G)................................................................................................................ 8
Power Board (WV-CS604E) ................................................................................................................... 9
Auto Focus Board (WV-CST600/G)........................................................................................................ 11
Digital Board (WV-CST600/G)................................................................................................................ 12
Drive Board/Drive Sub Board (WV-CST600/G) ...................................................................................... 13
Conductor View
Sensor Board (WV-CST600/G) .............................................................................................................. 8
Power Board (WV-CS604E) ................................................................................................................... 10
Exploded View ......................................................................................................................................... 14
Replacement Parts List ........................................................................................................................... 15
E*
R
T
W
Q Y
(1) Data Cable (only for WV-CSR600) (6) Fall Prevention Wire
1
INSTALLATION 2. Setting the switches
Set the switches as follows:
Precaution:
The following installations should be made by qualified Switch C (DIP Switches)
service personnel or system installers.
DIP 1
DIP 2
DIP 3
DIP φ
ON
Full Half
(4 lines) (2 lines)
Notes:
• Select OFF after resetting the parameters by selecting
ON.
• The factory settings is OFF.
Diecast Case
DIP 1 DIP 2
OFF OFF 01 - 32
Camera Unit No. OFF ON 33 - 64
ON OFF 65 - 96
ON ON Inhibition
The factory settings for the dip switch 1 and 2 are both OFF.
2
OFF NTSC (EIA) b. Top cable exit
PAL (CCIR) or DIP φ
NTSC (EIA) ON PAL (CCIR)
Note: The dip switch φ is not for changing NTSC (EIA) to
PAL (CCIR) or PAL (CCIR) to NTSC (EIA). This switch
is set at factory. Do not change the setting of this
switch. The factory setting is ON.
Diecast Case
3
4. Hook the fall prevention wire on the camera mounting 2. Follow the instructions given here to ensure that the
angle. camera and camera mounting angle are installed
safely.
3. When removing the camera from the camera
mounting angle, loosen and press up the camera
fixing screw (M3) by using a screwdriver.
15°
4
CONNECTIONS
Precaution:
The following connections should be made by qualified service personnel or system installers.
220 - 240V AC
WV-CS604E or WV-BS504E
24V AC
Data cable (Only for WV-CSR600) RS485 cable
Video Output
Cable BNC Plug Coaxial Cable
(5C - 2V)
BNC Plug
Note: When powered up, the unit performs a self-check (including one panning, tilting,
zooming and focusing operation).
5
SYSTEM CONNECTIONS
Combination Camera
TL TL
TL TL
Matrix
Personal Computer Switcher VTRs (up to 16)
RS-232C Port
CPU CONTROL ALARM INPUT INPUT DATA INPUT INPUT INPUT INPUT INPUT OUTPUT OUTPUT OUTPUT OUTPUT
RS-232C VIDEO OUT1 VIDEO OUT1 (RS485) VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1 VIDEO OUT1
A
A
B
1
00
R
B
DATA 2
G
MODE
A
5 CAMERA IN CAMERA IN T CAMERA IN CAMERA IN CAMERA IN CAMERA IN CAMERA IN
B
A
DATA 3 1 1 R 2 1 1 1 1 1
B
TEST G
A ALARM OUT ALARM OUT ALARM OUT ALARM OUT
TIME T
ADJUST IN RESET 2 2 B 2 2 2 2 2 RESET OUT RESET OUT RESET OUT RESET OUT
COM DATA 4 A MONITOR MONITOR MONITOR MONITOR +9V
R 3
1-32 B
G +5V
3 3 3 3 3 3 3
A IN IN IN IN
T
DATA 5 B 1 1 1 1 −5V
A OUT OUT OUT OUT
R 4
PRINTER 4 4 B 4 4 4 4 4
G
DATA 6 POWER
A
5 5 T 5 5 5 5 5 IN IN IN IN
B 2 2 2 2
ON
A
1
OUT OUT OUT OUT
R
DATA 7 B
6 6 G 6 6 6 6 6 OFF
A
33-64 T
B
A
DATA 8 7 7 R 2
7 7 7 7 7
VS/VD B IN IN IN IN
Printer IN
8 8
G
T
A
B
8 8 8 8 8
3
OUT
3
OUT
3
OUT
3
OUT
TEST 1 A
R 3
B
OUT
G
A
T IN IN IN IN
TEST 2 B 4 4 4 4 11A00001
A OUT OUT OUT OUT
R 4
VD B
OUT
G
VIDEO OUT2 VIDEO OUT2 VIDEO OUT2 VIDEO OUT2 VIDEO OUT2 VIDEO OUT2 VIDEO OUT2
System Status
Monitor
Note: Eight cameras are maximum that can be connected with a data board even if the cameras are connected by the daisy chain
connection.
6
SCHEMATIC DIAGRAM OF SENSOR BOARD
FOR WV-CST600/G
SENSOR BOARD
B
R6
IC1 D2 CN1
1 14 1 ∗R
2
V∗4 H∗2
13 2 ∗H2
3
V∗3 H∗1
12 3 ∗H1
V∗2 RG 4 SUB
4 11
R8 5
V∗1 VL
10 5 ∗V4
NC ∗SUB 6 ∗V3
6 9
7
GND GND
8 7 ∗V2 TO
VOUT VDD 8 ∗V1 MAIN
9 –8V
CCD IMAGE SENSOR BOARD
10 15V
R5 . . . CN1
11 GND
D1
Q1 VIA
R1 12 CCD OUT
13 GND
FLEXIBLE
14 GND CONNECTOR
R3
C2
+
C3
– 15 GND
R2
16 GND
A
R7
17 GND
R4
C1
18 GND
19 GND
20 20V
1 2
<Index>
Sensor Board
IC1 A1/B1
Q1 A1
D1 A2
D2 B2
7
EXPLODED VIEW
Numbers show Screws and Washers. 5 4 18
No. Screws Description
Q XSB2+4FX Binding Head Screw
W XTB2+4GFXK Binding Head Tapping Black Screws 11 M28 M44
M87
E XYN2+J4FN Machine Screw and Washer Ass'y 12
R XYM2+J6FN Machine Screw and Washer Ass'y
M83 M84
T XTB2+6GFXK Binding Head Tapping Black Screws
for WV-CST600
M82 M21
Y XS2+5FX Binding Head Screws 11
U XSB26+4FX Binding Head Screws M86 PB1
I XSB26+15FX Binding Head Screws for WV-CST600 M88
O XYN26+J6FN Machine Screw and Washer Ass'y 27
P XYN26+F15FN Machine Screw and Washer Ass'y
{ XSS26+4FX Flush Head Screws M25
} XSS26+16FX Flush Head Screws M81
q YWV1EC0270A4 Cup Head Screws
M22 M29 27
w XQN2+A4FN Precision Pan Head Screws M30
14
e XYN3+F8FX Machine Screw and Washer Ass'y 1
r XYN3+F12FX Machine Screw and Washer Ass'y 9
t XSS4+6FX Flush Head Screws 7
M85 M23 M35
y XSS4+12FX Flush Head Screws 1
u XVE4A8FX Hexagon Hole Head Bolts
i
26
XSB4+6FX Binding Head Screws
o XWC4BFX External Toothed Lock Washer
p
M18 M31
XSB26+12FX Binding Head Screws
[ XQN2+A8FN Precision Pan Head Screws MO3 M50 15
] XSB2+3FXK Binding Head Black Screws
A XSB3+4FXK Binding Head Black Screws M33
1 PCB6 20
M1 8
M36
1 M24
M37 M49
M34
FB1 7 16
CN2
FB2 M23 M26 21
M19 M27
M4 CN4
14 M38
15 M39
CN1 PCB2 M3 11
PCB7
CN3 CN5 19 CN101
FB3 M41
PCB1 1 11 22
M32 CN6 M47 17
7 M6 E101
2 17 M53
23 M55 17
4 M7
M5 13 M20 M42
5 13 E102
14 M57 M40
24 23
M52 M51
M8 M58
M54
9 M56
M9 25
9 18 11
M48 13 25 Serial No. Label
M46 M10 14
M45 PCB3 PCB5
PACKAGING
CN10
M60,61
M70
M64
7 M11 M62 M63
8 10 7
M70
M12 M15 8
7 3
M17
13
– 14 –
Printed in Japan
C-631 N 5, 7, 23