Professional Documents
Culture Documents
X95
"The repair methods given by the manufacturer in this document are based on the technical All copyrights reserved by Renault.
specifications current when it was prepared.
The reproduction or translation in part of whole of the present document, as well as the use
The methods may be modified as a result of changes introduced by the manufacturer in the of the spare parts reference numbering system, are prohibited without the prior written
production of the various component units and accessories from which his vehicles are consent of Renault.
constructed."
Contents
Page
REMOVAL
D95
I - REMOVAL PREPARATION OPERATION a Remove:
a Disconnect the battery (see Battery: Removal - Re- - the door sill lining (see 71A, Body internal trim,
fitting) (80A, Battery). Door sill lining: Removal - Refitting, page 71A-
a Remove: 25) ,
- the front seats completely (see 75A, Front seat - the rear panel trim (see 71A, Body internal trim,
frames and mechanisms, Complete front seat: Rear panel trim: Removal - Refitting, page 71A-
Removal - Refitting, page 75A-28) , 54) .
71A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
B95 or D95 or K95
135098
a Remove the clips (3) .
135097
a Remove:
- the accelerator pedal stop (5) ,
- the floor carpet.
REFITTING
II - FINAL OPERATION
D95
a Refit:
- the rear panel trim (see 71A, Body internal trim,
Rear panel trim: Removal - Refitting, page 71A-
54) ,
- the door sill lining (see 71A, Body internal trim,
Door sill lining: Removal - Refitting, page 71A-
25) .
71A-2
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
B95 or D95 or K95
B95 or K95
a Refit:
a Refit the 1/3 and 2/3 rear bench seat base (see 1/3
and 2/3 rear bench seat:Removal - Refitting) .
a Refit the single unit rear bench seat base (see 76A,
Rear seat frames and mechanisms, Single unit
rear bench seat: Removal - Refitting, page 76A-6)
.
a Refit:
71A-3
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
J95
REMOVAL
1 - Rear section
a Remove the complete rear seats.
139539
a Remove:
- the floor storage flaps (see Floor flap and stora-
ge: Removal - Refitting) (57A, Interior equip-
ment),
- the clips (2) of the rear floor carpet in the rear sto-
rage compartments using the tool (Car. 1363).
- the B-pillar lower trims (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) ,
- the rear inner sill upper trims (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the rear door sill linings (see 71A, Body internal
trim, Rear door sill lining: Removal - Refitting,
page 71A-31) .
71A-4
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
J95
139537
140474
a Remove the trim from the rear seats mounting rail.
a Remove the seat belt strap output trims (3) of the se-
cond row seats. 2 SEATS 3RD ROW
139535
2 - Front section
a Remove the complete rear seats (see 75A, Front
seat frames and mechanisms, Complete front
seat: Removal - Refitting, page 75A-28) .
a Move the sliding centre console backwards.
a Unclip:
- the diagnostic socket cover at the front of the cen-
tre console,
71A-5
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
J95
- the front door sill linings (see 71A, Body internal 2 - Front section
trim, Front door sill lining: Removal - Refitting,
page 71A-27) ,
- the front floor flaps (see Floor flap and storage:
Removal - Refitting) (57A, Interior equipment).
1 - Rear section
a Remove the rear floor carpet.
141428
141429
a Remove:
- the clips (9) and (10) ,
- the front floor carpet.
71A-6
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
J95
REFITTING
0 SEAT 3RD ROW
I - REFITTING OPERATION FOR PART
a Refit:
CONCERNED
- the luggage compartment floor lining (see 71A,
Body internal trim, Luggage compartment floor
1 - Front section lining: Removal - Refitting, page 71A-62) ,
a Refit: - the seat belt strap output trims (3) of the second
row seats.
- the front floor carpet,
- the front floor carpet clips (9) and (10) .
a Refit:
2 - Rear section
- the rear door sill linings (see 71A, Body internal
a Refit the rear floor carpet.
trim, Rear door sill lining: Removal - Refitting,
page 71A-31) ,
II - FINAL OPERATION - the rear inner sill upper trims (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
1 - Front section Refitting, page 71A-45) ,
- the B-pillar lower trims (see 71A, Body internal
a Clip:
trim, B-pillar lower trim: Removal - Refitting,
- the front floor flaps (see Floor flap and storage: page 71A-29) ,
Removal - Refitting) ,
- the clips (2) of the rear floor carpet in the rear sto-
- the front door sill linings (see 71A, Body internal rage compartments,
trim, Front door sill lining: Removal - Refitting, - the floor storage flaps (see Floor flap and stora-
page 71A-27) , ge: Removal - Refitting) (57A, Interior equip-
- the diagnostic socket cover at the front of the cen- ment),
tre console. - the bolts (1) of the sliding centre console,
a Move the sliding centre console forwards. - the complete rear seats.
a Refit the complete rear seats (see 75A, Front seat
frames and mechanisms, Complete front seat: 3 - Final operation common to both sections
Removal - Refitting, page 75A-28) .
a Reconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
2 - Rear section
71A-7
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
D95
- the interior lights (see Courtesy light: Removal -
Essential special tooling Refitting) (81B, Interior lighting),
Car. 1363 Set of trim removal levers. - the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-
IMPORTANT nal trim, A-pillar trim: Removal - Refitting, page
71A-37) .
To avoid any risk of damaging the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out the
repair (see Airbag and Pretensioners: Precau-
tions for repair) (88C, Airbags and pretensioners).
REMOVAL
137499
137500
a Disconnect the headlining wiring connectors.
137004
a Remove: REAR BENCH FUNCTION
- the upper cover of the interior rear view mirror a Remove the single unit rear bench seat base (see
using the tool (Car. 1363), 76A, Rear seat frames and mechanisms, Single
unit rear bench seat: Removal - Refitting, page
- the lower cover of the interior rear view mirror. 76A-6) .
a Unclip the lower cover from the interior rear view
mirror.
a Disconnect the interior rear view mirror connectors.
a Remove:
- the side door seals partially,
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
71A-8
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
D95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1-2/3 REAR BENCH SEAT + ARMREST + N/R
SEATBACK
a Remove the 1/3 and 2/3 rear bench seat base (see
1/3 and 2/3 rear bench seat:Removal - Refitting) .
a Remove:
- the side roof rail rear trims (see 71A, Body inter-
nal trim, Rear roof drip moulding lining: Remo-
val - Refitting, page 71A-38) ,
- the rear parcel shelf side trims (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) ,
137510
a Unclip the rear mountings.
137503
71A-9
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
D95
137174
137508
a Unclip the trims.
137498
137509
a Unclip the side mountings at (2) using a flat-blade
screwdriver.
137486
71A-10
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
D95
II - REFITTING OPERATION FOR PART
CONCERNED
Note:
For vehicles equipped with a sunroof, the headli-
ning must be handled with care. The side edges
are weakened by the design of the sunroof.
a Refit:
- the rear quarter panel trims (see 71A, Body inter-
nal trim, Rear quarter panel trim: Removal - Re-
fitting, page 71A-48) ,
- the rear parcel shelf side trims (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) ,
- the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-39) ,
71A-11
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
D95
71A-12
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B95 or K95
IMPORTANT
REMOVAL
PANORAMIC SUNROOF
a Remove the sunroof switch (see Sunroof switch:
Removal - Refitting) (87D, Electric windows - Sun-
roof).
137499
a Disconnect the headlining wiring connectors (1) .
a Remove:
PANORAMIC SUNROOF
- the interior lights (see Courtesy light: Removal -
a Disconnect the sunroof wiring connectors.
Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
- the courtesy lights (see Vanity light: Removal -
Refitting) (81B, Interior lighting),
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-
nal trim, A-pillar trim: Removal - Refitting, page
71A-37) .
71A-13
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B95 or K95
PANORAMIC SUNROOF
137004
137172
137003
1-2/3 REAR BENCH SEAT + ARMREST + N/R
SEATBACK
a Remove:
a Remove the 1/3 and 2/3 rear bench seat base (see
- the upper cover of the interior rear view mirror (2)
1/3 and 2/3 rear bench seat:Removal - Refitting) .
using the tool (Car. 1363),
- the lower cover of the interior rear view mirror.
a Disconnect the connectors (3) on the interior rear
view mirror. a Remove:
- the side door seals partially,
- the luggage compartment seal partially,
- the B-pillar lower trims (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) ,
71A-14
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B95 or K95
- the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-39) ,
137482
a Unclip the headlining central section (6) .
137511
137175
a Unclip the rear mountings.
a Remove the headlining (this operation requires two
people).
PANORAMIC SUNROOF
a
Note:
For vehicles equipped with a sunroof, the headli-
ning must be handled with care. The side edges
are weakened by the design of the sunroof.
137174
71A-15
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B95 or K95
Note:
For vehicles equipped with a sunroof, the headli-
ning must be handled with care. The side edges
are weakened by the design of the sunroof.
a Clip on:
a Refit:
a Refit the 1/3 and 2/3 rear bench seat base (see 1/3
and 2/3 rear bench seat:Removal - Refitting) .
71A-16
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B95 or K95
a Connect the battery (see Battery : Removal - Refit-
ting) (80A, Battery).
REAR BENCH FUNCTION
a Refit the single unit rear bench seat base (see 76A,
Rear seat frames and mechanisms, Single unit
rear bench seat: Removal - Refitting, page 76A-6)
.
PANORAMIC SUNROOF
a Refit the finishing seal.
PANORAMIC SUNROOF
a Connect the sunroof wiring connectors.
a Refit:
- the windscreen pillar trims (see 71A, Body inter-
nal trim, A-pillar trim: Removal - Refitting, page
71A-37) ,
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the courtesy lights (see Vanity light: Removal -
Refitting) (81B, Interior lighting),
PANORAMIC SUNROOF
a Refit the sunroof switch (see Sunroof switch: Re-
moval - Refitting) (87D, Electric windows - Sun-
roof).
71A-17
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
IMPORTANT
REMOVAL
141410
a Remove:
71A-18
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
NORMAL ROOF
141403
141404
141402 a Remove the additional rear view mirror.
a Unclip the additional rear view mirror mounting at (4)
using the tool (Car. 1363).
a Remove:
71A-19
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
- the courtesy lights (see Vanity light: Removal -
Refitting) (81B, Interior lighting),
PANORAMIC SUNROOF
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-
nal trim, A-pillar trim: Removal - Refitting, page
71A-37) .
NORMAL ROOF
141411
a Disconnect:
142228
a Disconnect the connector (6) from the headlining wi-
ring.
142227
71A-20
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
a Unclip the casings of the interior rear view mirror - the rear quarter panel trims (see 71A, Body inter-
using the tool (Car. 1363). nal trim, Rear quarter panel trim: Removal - Re-
fitting, page 71A-48) ,
- the B-pillar lower trims (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) ,
- the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-39) ,
141407
AUTO LIGHTS+WIPER
a Remove:
- the rear inner sill upper trims (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
71A-21
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
137174
a Unclip the headlining front section at (15) .
137511
137482
a Unclip the headlining central section at (16) .
a Pass the rear central seat belt inside the headlining.
97193
a Remove the rear clips at (13) by pressing on the clip
(14) using a small flat-blade screwdriver.
71A-22
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
REFITTING
137483
a Check the presence and the condition of the velcro
141406 strips at (17) .
a Remove the headlining (this operation requires two
people).
II - REFITTING OPERATION FOR PART
CONCERNED
PANORAMIC SUNROOF
a PANORAMIC SUNROOF
Note: a
71A-23
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
J95
- the rear quarter panel trims (see 71A, Body inter-
nal trim, Rear quarter panel trim: Removal - Re-
fitting, page 71A-48) , NORMAL ROOF
- the rear wheel arch trims (see 71A, Body internal a Refit the additional rear view mirror.
trim, Rear wheel arch lining: Removal - Refit-
ting, page 71A-33) ,
- the rear parcel shelf side trim panels (see 71A,
Body internal trim, Rear parcel shelf side trim:
PANORAMIC SUNROOF
Removal - Refitting, page 71A-56) ,
a Refit:
- the rear inner sill upper trims (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal - - the front and rear finishing seals,
Refitting, page 71A-45) , - the sunroof switch (see Sunroof switch: Removal
- the luggage compartment floor trims (see 71A, - Refitting) (87D, Electric windows - Sunroof).
Body internal trim, Luggage compartment floor
lining: Removal - Refitting, page 71A-62) ,
- the rear end panel lining (see 71A, Body internal a Connect the battery (see Battery: Removal - Refit-
trim, Rear end panel lining: Removal - Refitting, ting) (80A, Battery).
page 71A-60) ,
a Connect the connectors of:
- of the rear view mirror,
- of the interior temperature sensor.
AUTO LIGHTS+WIPER
a Connect the rain and light sensor connector.
PANORAMIC SUNROOF
a Connect the sunroof wiring connector.
a Refit:
- the windscreen pillar trims (see 71A, Body inter-
nal trim, A-pillar trim: Removal - Refitting, page
71A-37) ,
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the courtesy lights (see Vanity light: Removal -
Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
- the interior lights (see Courtesy light: Removal -
Refitting) (81B, Interior lighting).
71A-24
BODY INTERNAL TRIM
Door sill lining: Removal - Refitting 71A
D95
137316
137119
a Remove:
- the front side door seal partially,
- the bonnet release handle (1) ,
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) .
137121
a Remove the door sill lining (2) .
71A-25
BODY INTERNAL TRIM
Door sill lining: Removal - Refitting 71A
D95
II - FINAL OPERATION
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) ,
- the bonnet release handle,
- the front side door seal.
137115
137117
REFITTING
a Refit:
71A-26
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting 71A
B95 or J95 or K95
REMOVAL
138754
138756
a Remove: II - OPERATION FOR REMOVAL OF PART
- the front side door seal partially, CONCERNED
138755
a Remove the front door sill lining (2) , using the tool
(Car. 1363).
71A-27
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting 71A
B95 or J95 or K95
II - FINAL OPERATION
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) ,
- the bonnet release control (1) from the left-hand si-
de,
- the front side door seal.
138757
137117
REFITTING
a Refit:
71A-28
BODY INTERNAL TRIM
B-pillar lower trim: Removal - Refitting 71A
B95 or J95 or K95
137107
137109
a Remove the B-pillar lower trim at (1) and (2) .
71A-29
BODY INTERNAL TRIM
B-pillar lower trim: Removal - Refitting 71A
B95 or J95 or K95
II - FINAL OPERATION
138798
138924
a Remove the B-pillar lower trim at (3) and (4) .
REFITTING
71A-30
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting 71A
B95 or J95 or K95
137099
137102
a Remove:
71A-31
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting 71A
B95 or J95 or K95
J95
139009
a Separate the rear wheel arch trim at (3) .
a Remove the rear door sill lining (4) .
REFITTING
II - FINAL OPERATION
a Refit:
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) .
71A-32
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting 71A
B95 or D95 or K95
B95 or K95
a Remove:
- the rear end panel lining (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) ,
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) .
D95
a Remove:
- the side roof rail rear trim (see 71A, Body internal
trim, Rear roof drip moulding lining: Removal -
Refitting, page 71A-38) ,
- the rear panel trim (see 71A, Body internal trim, 137096
Rear panel trim: Removal - Refitting, page 71A- a Remove the rear wheel arch trim (1) .
54) ,
- the rear end panel trim (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) .
D95
137094
a Remove the rear wheel arch trim (2) .
71A-33
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting 71A
B95 or D95 or K95
- the side roof rail rear trim (see 71A, Body internal
trim, Rear roof drip moulding lining: Removal -
K95 Refitting, page 71A-38) .
B95 or K95
a Refit:
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the rear end panel trim (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) .
142073
a Remove:
- the rear wheel arch trim bolt (3) ,
- the rear wheel arch trim clip (4) ,
- the rear wheel arch trim.
REFITTING
II - FINAL OPERATION
a Refit the rear parcel shelf side trim (see 71A, Body
internal trim, Rear parcel shelf side trim: Remo-
val - Refitting, page 71A-56) .
D95
a Refit:
- the rear end panel lining (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) ,
- the rear panel trim (see 71A, Body internal trim,
Rear panel trim: Removal - Refitting, page 71A-
54) ,
71A-34
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting 71A
J95
REMOVAL
a Remove:
- the rear end panel lining (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) ,
a Remove the rear inner sill trim (see 71A, Body in- a Remove the rear wheel arch trim (3) .
ternal trim, Rear door sill lining: Removal - Refit-
ting, page 71A-31) .
a Remove the rear parcel shelf side trim (see Rear STANDARD CHASSIS
parcel shelf trim: Removal - Refitting) .
LONG CHASSIS
142082
a Remove:
138804
71A-35
BODY INTERNAL TRIM
Rear wheel arch lining: Removal - Refitting 71A
J95
REFITTING
LONG CHASSIS
a Connect the luggage compartment light connector
(2) .
a Refit:
- the rear wheel arch trim,
- the clip of the wheel arch trim.
II - FINAL OPERATION
a Refit the rear parcel shelf side trim (see Rear parcel
shelf trim: Removal - Refitting) .
LONG CHASSIS
a Refit the rear door sill lining (see 71A, Body internal
trim, Rear door sill lining: Removal - Refitting,
page 71A-31) .
a Refit:
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the luggage compartment floor lining (see 71A,
Body internal trim, Luggage compartment floor
lining: Removal - Refitting, page 71A-62) ,
- the rear end panel trim (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) .
71A-36
BODY INTERNAL TRIM
A-pillar trim: Removal - Refitting 71A
B95 or D95 or J95 or K95
REFITTING
Essential special tooling
Car. 1363 Set of trim removal levers. I - REFITTING OPERATION FOR PART
CONCERNED
REMOVAL a Insert the lower section of the windscreen pillar trim.
a Clip on the entire length of the A-pillar trim.
I - REMOVAL PREPARATION OPERATION
II - FINAL OPERATION
a Partially remove the front side door seal.
a Refit the front side door seal.
138799
138800
71A-37
BODY INTERNAL TRIM
Rear roof drip moulding lining: Removal - Refitting 71A
D95
REMOVAL REFITTING
137086
137089
a Remove the rear side roof rail (1) .
71A-38
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
D95
Tightening torquesm
REMOVAL
137792
a Remove the trim (1) of the front side seat belt return
mechanism.
137066
a Remove the bolts (3) of the B-pillar upper trim.
71A-39
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
D95
137068
REFITTING
II - FINAL OPERATION
a Refit:
- the side roof rail rear trim (see 71A, Body internal
trim, Rear roof drip moulding lining: Removal -
Refitting, page 71A-38) .
71A-40
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
B95 or J95 or K95
Tightening torquesm
REMOVAL
139020
139018
a Unclip the trim by pressing on the locking clips (1)
using a flat-blade screwdriver.
a Remove the trim (2) .
71A-41
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
B95 or J95 or K95
- the guide of the front side seat belt return mecha-
nism.
J95
137457
a Remove:
- the bolt (3) ,
- the front side seat belt return mechanism.
B95 139022
a Remove:
- the clip (5) ,
- the heating duct from the B-pillar (6) .
137036
a Remove:
- the bolt (4) ,
71A-42
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
B95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
B95
137438 137072
a Remove the clips (9) .
a Use a flat-blade screwdriver to press at (7) to re-
lease the lower section of the trim. a Unclip the lower section of the B-pillar upper trim.
J95
139024
139023 a Remove the B-pillar upper trim at (10) and (11) .
a Apply pressure to (8) .
71A-43
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
B95 or J95 or K95
REFITTING
II - FINAL OPERATION
J95
a Refit:
- the heating duct of the B-pillar (6) ,
- the clip (5) .
B95
a Refit the guide of the front side seat belt return me-
chanism.
71A-44
BODY INTERNAL TRIM
Rear door sill upper lining: Removal - Refitting 71A
B95 or J95 or K95
B95
a Pull down the rear seatback.
137452
137453
a Remove the rear door sill upper trim at (1) .
71A-45
BODY INTERNAL TRIM
Rear door sill upper lining: Removal - Refitting 71A
B95 or J95 or K95
II - FINAL OPERATION
B95
a Lock the rear bench seatback.
138794
138795
a Remove the rear door sill upper trim at (2) .
REFITTING
71A-46
BODY INTERNAL TRIM
C-pillar upper trim: Removal - Refitting 71A
D95
REMOVAL
a Remove:
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) ,
137448
REFITTING
II - FINAL OPERATION
a Refit:
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) .
71A-47
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
B95 or D95 or K95
- the bolt (2) of the rear side seat belt return mecha-
nism,
Tightening torquesm
- the rear side seatbelt return mechanism.
bolt of the rear side seat 21 N.m
belt return mechanism
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
K95
139002
a Remove:
- the trim (1) ,
71A-48
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
B95 or D95 or K95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
D95
B95
137448
137451
137449
a Remove the rear quarter panel trim (4) .
137450
a Remove the rear quarter panel trim (3) .
71A-49
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
B95 or D95 or K95
142229 D95
a Refit:
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) ,
- the rear panel trim (see 71A, Body internal trim,
Rear panel trim: Removal - Refitting, page 71A-
54) ,
- the C-pillar upper trim (see 71A, Body internal
trim, C-pillar upper trim: Removal - Refitting,
page 71A-47) .
142075
a Remove the rear quarter panel trim (5) .
REFITTING
II - FINAL OPERATION
K95
a Torque tighten the bolt of the rear side seat belt
return mechanism (21 N.m).
a Refit the trim (1)
71A-50
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
J95
Tightening torquesm
REMOVAL
139002
a Remove:
71A-51
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
J95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
STANDARD CHASSIS
LONG CHASSIS
142083
139000
142087
a Remove the rear quarter panel trim at (5) .
139001
a Remove the rear quarter panel trim at (4) .
REFITTING
71A-52
BODY INTERNAL TRIM
Rear quarter panel trim: Removal - Refitting 71A
J95
II - FINAL OPERATION
a Refit:
- the rear side seatbelt return mechanism,
- the bolt (3) .
a Torque tighten the bolt of the rear side seat belt
return mechanism (21 N.m).
a Refit:
- the trim (2)
- the rear wheel arch trim (see 71A, Body internal
trim, Rear wheel arch lining: Removal - Refit-
ting, page 71A-33) ,
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-56) ,
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the rear end panel trim (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) .
71A-53
BODY INTERNAL TRIM
Rear panel trim: Removal - Refitting 71A
D95
Tightening torquesm
REMOVAL
137825
a Remove:
REAR BENCH SEAT
a Remove the single unit rear bench seat base (see - the bolt (1) of the guide rail of the front side seat
76A, Rear seat frames and mechanisms, Single belt return mechanism,
unit rear bench seat: Removal - Refitting, page - the guide rail of the front side seat belt return me-
76A-6) . chanism.
a Tilt the rear bench seatback.
a Remove the rear panel upper trim.
a Remove:
- the door sill lining (see 71A, Body internal trim,
Door sill lining: Removal - Refitting, page 71A-
25) ,
- the side roof rail rear trim (see 71A, Body internal
trim, Rear roof drip moulding lining: Removal -
Refitting, page 71A-38) .
71A-54
BODY INTERNAL TRIM
Rear panel trim: Removal - Refitting 71A
D95
II - OPERATION FOR REMOVAL OF PART REFITTING
CONCERNED
II - FINAL OPERATION
a Refit the rear panel upper trim.
a Fit the rear bench seatback.
a Refit the guide rail of the front side seat belt return
mechanism.
a Torque tighten the bolt of the guide rail of the
front side seat belt return mechanism (21 N.m).
a Refit:
- the side roof rail rear trim (see 71A, Body internal
trim, Rear roof drip moulding lining: Removal -
Refitting, page 71A-38) ,
137446
- the door sill lining (see 71A, Body internal trim,
a Remove: Door sill lining: Removal - Refitting, page 71A-
- the bolt (2) of the rear panel trim, 25) .
137507
a Disconnect the rear speaker connector (3) .
a Remove the rear panel trim.
71A-55
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting 71A
REMOVAL II - OPERATION FOR REMOVAL OF PART
CONCERNED
D95
a Remove:
- the rear end panel lining (see 71A, Body internal
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) ,
- the rear panel upper trim,
- the rear panel trim partially (see 71A, Body inter-
nal trim, Rear panel trim: Removal - Refitting,
page 71A-54) . 137439
J95 or K95
137441
a Remove the rear door upper sill trim (see 71A, Body
a Remove:
internal trim, Rear door sill upper lining: Remo-
val - Refitting, page 71A-45) . - the bolts (1) ,
- the rear parcel shelf side trim (2) .
71A-56
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting 71A
D95 J95, and STANDARD CHASSIS
136672
142085
137445
a Remove:
- the bolts (3) ,
- the rear parcel shelf side trim (4) .
142084
a Remove:
- the bolts (5) ,
- partially the side trim (6) of the rear parcel shelf,
- the electrical accessories socket (see Electrical
accessories socket: Removal - Refitting) (88D,
Driver's position),
- the rear parcel shelf side trim (6) .
71A-57
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting 71A
J95, and LONG CHASSIS K95
138801 142072
138803 142074
a Remove: a Remove:
- the bolts (7) , - the bolts (9) ,
- partially the side trim (8) of the rear parcel shelf, - partially the side trim (10) of the rear parcel shelf,
- the electrical accessories socket (see Electrical - the electrical accessories socket (see Electrical
accessories socket: Removal - Refitting) (88D, accessories socket: Removal - Refitting) (88D,
Driver's position), Driver's position),
- the rear parcel shelf side trim (8) . - the rear parcel shelf side trim (10) .
71A-58
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting 71A
REFITTING
J95 or K95
II - FINAL OPERATION
J95 or K95
a Refit the rear inner sill upper trim (see 71A, Body in-
ternal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) .
D95
a Refit:
71A-59
BODY INTERNAL TRIM
Rear end panel lining: Removal - Refitting 71A
B95 or D95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART
Essential special tooling CONCERNED
Car. 1363 Set of trim removal levers.
B95 or D95
REMOVAL
B95 or D95
a Partially remove the luggage compartment carpet.
J95
137440
a Remove the luggage compartment floor lining (see
71A, Body internal trim, Luggage compartment
floor lining: Removal - Refitting, page 71A-62) .
137443
a Unclip the rear end panel trim at (1) and (2) .
a Remove the rear end panel trim.
71A-60
BODY INTERNAL TRIM
Rear end panel lining: Removal - Refitting 71A
B95 or D95 or J95 or K95
J95
138806
a Remove the rear end panel trim using the tool (Car.
1363).
REFITTING
II - FINAL OPERATION
B95 or D95
J95
71A-61
BODY INTERNAL TRIM
Luggage compartment floor lining: Removal - Refitting 71A
J95, and LONG CHASSIS, and 0 SEAT 3RD ROW or 2 SEATS 3RD ROW
REMOVAL
2 SEATS 3RD ROW
I - REMOVAL PREPARATION OPERATION
- the rear inner sill upper trims (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
141417
0 SEAT 3RD ROW
a Remove the luggage compartment floor trims (2)
and (3) .
REFITTING
a Refit:
138807
71A-62
BODY INTERNAL TRIM
Luggage compartment floor lining: Removal - Refitting 71A
J95, and LONG CHASSIS, and 0 SEAT 3RD ROW or 2 SEATS 3RD ROW
II - FINAL OPERATION
71A-63
BODY INTERNAL TRIM
Rear load compartment lining: Removal - Refitting 71A
B95, and UTILITY
REMOVAL
138446
a Unclip the quick releases.
a Remove the luggage cover shelf.
138449
a Remove the bolts (2) .
138447
a Remove the emergency spare wheel cover.
71A-64
BODY INTERNAL TRIM
Rear load compartment lining: Removal - Refitting 71A
B95, and UTILITY
REFITTING
II - FINAL OPERATION
a Refit:
- the rear end panel lining (see 71A, Body internal
138444
trim, Rear end panel lining: Removal - Refitting,
page 71A-60) ,
a Remove:
- the luggage compartment seal.
- the bolts (3) ,
- the luggage cover frame.
138445
a Remove:
- the clips (4) ,
- the side trim of the load stop floor.
71A-65
BODY INTERNAL TRIM
Luggage retaining assembly: Removal - Refitting 71A
B95, and UTILITY
REMOVAL
138450
a Remove the bolts (1) .
138451
a Remove the bolt of the load stop bracket (2) .
71A-66
BODY INTERNAL TRIM
Luggage retaining assembly: Removal - Refitting 71A
B95, and UTILITY
REFITTING
II - FINAL OPERATION
a Refit:
- the rear loading trim (see 71A, Body internal trim,
Rear load compartment lining: Removal - Refit-
ting, page 71A-64) .
- the rear door sill lining (see 71A, Body internal
138453
trim, Rear door sill lining: Removal - Refitting,
page 71A-31) ,
- the rear inner sill upper trim (see 71A, Body inter-
nal trim, Rear door sill upper lining: Removal -
Refitting, page 71A-45) ,
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-29) .
138459
a Remove:
- partially remove the floor carpet,
- the bolts (3) ,
- the « bracket supports - load stop bracket » as-
sembly.
71A-67
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
Essential special tooling
B95 or D95
Car. 1363 Set of trim removal levers.
REMOVAL
137394
a Remove the rear view mirror interior trim.
137392
a Remove the trim of the front side door handle using
the tool (Car. 1363) by inserting it at (1) .
139034
a Remove the blanking cover (2) .
72A-1
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
B95 or D95, and EQT LEVEL EA1 or EQT LEVEL
EA2
B95 or D95, and EQT LEVEL EA3 or EQT LEVEL
EA4
137405
J95
139010
72A-2
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
REFITTING
a Disconnect the front side door light. a Refit the blanking cover (2) .
a Unclip the front side door interior opening control ca-
ble. B95 or D95
a Disconnect the connectors from the front side door a Refit the door mirror interior trim.
window control switch plate.
139013
a Remove the front side door trim.
72A-3
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B95 or J95 or K95
REMOVAL
137396
137399
137398
a Unclip the clip (2) .
a Remove the manual window winder control handle.
137400
72A-4
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B95 or J95 or K95
B95 or K95
142218
a Remove the bolt (3) from the rear side door trim.
139035
a Remove the trim at (4) and (5) using the tool (Car.
1363).
J95
139014
a Remove the bolt (3) from the rear side door trim. 139034
a Remove:
- the blanking cover (6) ,
- the bolt (7) .
72A-5
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
139016
a Unclip:
REFITTING
- the rear side door trim,
- the interior opening release cable of the rear side I - REFITTING PREPARATION OPERATION
door.
a parts always to be replaced: Rear side opening
element trim clip (70,03,02,23).
FRONT FOOTWELL LIGHT
a Disconnect the rear side door light. II - REFITTING OPERATION FOR PART
CONCERNED
a Disconnect the connectors from the rear side door a Connect the tweeter speaker.
window control switch plate.
72A-6
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B95 or J95 or K95
a Clip on:
- the interior opening release cable of the rear side
door,
- the rear side door trim.
J95
a Refit the trim piece.
Note:
Refit the manual window winder handle for the
rear side door in a vertical position with the but-
ton at the bottom.
72A-7
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73A
REMOVAL
B95
OPERATION FOR REMOVAL OF PART
CONCERNED
B95 or K95
137385
a Remove the centre trim. 137391
a Remove:
- the bolts (1) ,
- the tailgate trim.
137387
a Remove the side trims.
73A-1
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73A
K95
137389
a Remove the side trims.
142079
a Remove:
- the bolts (2) ,
- the tailgate trim.
D95
137395
a Remove:
- the bolts (3) ,
- the tailgate trim.
137383
a Remove the centre trim.
73A-2
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73A
J95
139006
a Remove the bolts (6) .
139003
a Remove the central trim assembly.
139007
139005
a Remove the side trims at (4) and (5) .
139008
a Remove the tailgate trim.
73A-3
NON-SIDE OPENING ELEMENTS TRIM
Tailgate lining: Removal - Refitting 73A
REFITTING
Note:
Always check the condition of the clips and
replace them if necessary.
73A-4
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
a Remove:
- the front seat base trim (see 77A, Front seat trim,
Front seat base trim: Removal - Refitting, page
77A-1) .
- the front seat belt buckle stalk (see Front seat belt
buckle: Removal - Refitting) (88C, Airbags and
pretensioners).
75A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART REFITTING
CONCERNED
FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07 FRONT SEAT TYPE 01 or FRONT SEAT TYPE 02
or FRONT SEAT TYPE 03 or FRONT SEAT TYPE
05 or FRONT SEAT TYPE 06 or FRONT SEAT
TYPE 08
a Refit the front seat height adjustment motor (see
75A, Front seat frames and mechanisms, Front
seat height adjuster: Removal - Refitting, page
75A-11) .
D95 or E95
a Refit the anti-submarining airbag (see Anti-subma-
rining airbag: Removal - Refitting) (88C, Airbags
138034 and pretensioners).
a
Note:
The height adjustment motor mountings (2) can-
not be removed. B95 or J95 or K95
The Parts Department supplies the front seat a Refit the front seat lap belt pretensioner (see Front
frame assembled with the front seat height
seat lap belt pretensioner: Removal - Refitting)
adjustment motor.
(88C, Airbags and pretensioners).
75A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
a Refit:
- the front seat belt buckle stalk (see Front seat belt
buckle: Removal - Refitting) (88C, Airbag and
pretensioners),
- the front seat base trim (see 77A, Front seat trim,
Front seat base trim: Removal - Refitting, page
77A-1) ,
- the front seat lower casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) ,
- the front seat (see 75A, Front seat frames and
mechanisms, Complete front seat: Removal -
Refitting, page 75A-28) ,
- the front headrest (see 79A, Seat components,
Front headrest: Removal - Refitting, page 79A-
3) .
a Connect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
75A-3
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
J95
Note:
a Remove (see 79A, Seat components, Seatback
It is prohibited to carry out any welding operation on
tray: Removal - Refitting, page 79A-1) .
the frames of the seat and bench seat.
Note:
a Remove:
Depending on the method of sale defined by the
Parts Department, adaptations can be made to the - the front seat headrest guides (see 79A, Seat
seat frames. components, Front seat headrest guide: Remo-
In this case, it is permitted to eliminate certain com- val - Refitting, page 79A-7) ,
ponents (supports, wires, brackets, inserts, etc)
depending on vehicle type. - the front seatback « foam - cover » assembly (see
77A, Front seat trim, Front seatback trim: Re-
moval - Refitting, page 77A-4) ,
REMOVAL
- the front side (chest-level) airbag (see Front
(chest) side airbag: Removal - Refitting) (88C,
I - REMOVAL PREPARATION OPERATION Airbags and pretensioners).
a Disconnect the battery (see Battery : Removal -
Refitting) (80A, Battery).
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03
a Remove: or FRONT SEAT TYPE 04 or FRONT SEAT TYPE
- the front seat headrest (see 79A, Seat compo- 05 or FRONT SEAT TYPE 06 or FRONT SEAT
nents, Front headrest: Removal - Refitting, TYPE 07 or FRONT SEAT TYPE 08
page 79A-3) ,
a Remove the front seat lumbar adjustment mecha-
- the compete front seat (see 75A, Front seat fra- nism (see 75A, Front seat frames and mecha-
mes and mechanisms, Complete front seat: Re- nisms, Front seat lumbar adjustment: Removal -
moval - Refitting, page 75A-28) , Refitting, page 75A-14) .
- the front seat lower casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) .
75A-4
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
D95 or E95
a Remove the control support assembly for access to
the rear seats together with the seatback frame un-
locking cables (see Rear seat access mecha-
nisms: Removal - Refitting) .
138059
a Unclip the support (3) from the rear seat access ro-
tary switch using the tool (Car. 1363).
75A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART II - REFITTING OPERATION FOR PART
CONCERNED CONCERNED
138049
D95 or E95, and FRONT SEAT TYPE 04 or FRONT
SEAT TYPE 07
D95 or E95
REFITTING
FRONT SEAT TYPE 01
I - REFITTING PREPARATION OPERATION
a Refit the front seat lumbar pad.
a parts always to be replaced: Front seatback fra-
me mounting on front seat base frame (70,08,02,
09).
75A-6
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
- the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 moval - Refitting, page 75A-28) ,
or FRONT SEAT TYPE 04 or FRONT SEAT TYPE
05 or FRONT SEAT TYPE 06 or FRONT SEAT - the front headrest (see 79A, Seat components,
TYPE 07 or FRONT SEAT TYPE 08 Front headrest: Removal - Refitting, page 79A-
3) .
a Refit the front seat lumbar adjustment mechanism
(see 75A, Front seat frames and mechanisms, a Connect the battery (see Battery : Removal - Refit-
Front seat lumbar adjustment: Removal - Refit- ting) (80A, Battery).
ting, page 75A-14) . a Carry out a function test.
a Refit:
- the front side (chest-level) airbag (see Front
(chest) side airbag: Removal - Refitting) (88C,
Airbags and pretensioners),
- the front seatback « foam - cover » assembly (see
77A, Front seat trim, Front seatback trim: Re-
moval - Refitting, page 77A-4) ,
- the front seat headrest guides (see 79A, Seat
components, Front seat headrest guide: Remo-
val - Refitting, page 79A-7) .
J95
a Refit (see 79A, Seat components, Seatback tray:
Removal - Refitting, page 79A-1) .
D95 or E95
a Refit the rear seat access control (see Rear seat ac-
cess control: Removal - Refitting) .
a Refit:
- the front seat lower casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) ,
75A-7
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
REMOVAL
- the front seat lower casings (see 77A, Front seat a Unclip the front seat runner switch. (1) .
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) .
B95
a Remove the front seat lap belt pretensioner (see
Front seat lap belt pretensioner: Removal - Refit-
ting) (88C, Airbag and pretensioners).
75A-8
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
138018 139546
138019
139547
a Remove:
a Remove:
- the nuts from the front « seat base - runner » ,
- the nuts from the front « seat base - runner » ,
- the front seat runners.
- the front seat runners.
REFITTING
75A-9
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
B95
a Refit the front seat lap belt pretensioner (see Front
seat lap belt pretensioner: Removal - Refitting)
(88C, Airbags and pretensioners).
a Refit:
- the front seat lower casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) ,
- the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-28) ,
- the front headrest (see 79A, Seat components,
Front headrest: Removal - Refitting, page 79A-
3) .
139548 a Connect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
a Position the runners so that there is a centre-to-cen-
tre distance of 428.5 mm between the two rear a Carry out a function test.
mountings.
a Refit the front seat slide motor. (see 75A, Front seat
frames and mechanisms, Front seat sliding mo-
tor: Removal - Refitting, page 75A-17) .
75A-10
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjuster: Removal - Refitting 75A
J95
141511
a Remove:
REFITTING
a Refit:
75A-11
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjuster: Removal - Refitting 75A
J95
141492
a Refit the spring using the tool (Car. 1922) and a
hammer.
75A-12
FRONT SEAT FRAMES AND MECHANISMS
Front seat remote adjustment: Removal - Refitting 75A
138033
a
Note:
The torsion bar is used again on the front seat
height adjustment mechanism.
The front seat height adjustment mechanism
cannot be removed.
The Parts Department supplies the front seat
frame assembled with the front seat height
adjustment motor.
75A-13
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05 or
FRONT SEAT TYPE 06 or FRONT SEAT TYPE 07 or FRONT SEAT TYPE 08
D95 Note:
a Remove the rear seat access control (see 75A, For this operation, the lumbar pad must be loose.
Front seat frames and mechanisms, Front seat
backrest tilt control: Removal - Refitting, page
75A-21) .
138023
a Unclip the front seat lumbar pad in the order shown.
75A-14
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05 or
FRONT SEAT TYPE 06 or FRONT SEAT TYPE 07 or FRONT SEAT TYPE 08
138052 138053
a Remove the « lumbar adjustment mechanism - lum- a Clip on the front seat lumbar pad in the order shown.
bar pad » assembly.
Note:
Note:
The lumbar pad springs on the front seatback
The Parts Department supplies the lumbar frame are positioned with the hook facing
adjustment mechanism assembled with the lum- towards the rear.
bar pad.
a Carry out a function test.
REFITTING
II - FINAL OPERATION
I - REFITTING OPERATION FOR PART a Refit the front seat foam and cover assembly (see
CONCERNED 77A, Front seat trim, Front seatback trim: Remo-
a Refit the « lumbar adjustment mechanism - lumbar val - Refitting, page 77A-4) .
pad » assembly.
D95
75A-15
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05 or
FRONT SEAT TYPE 06 or FRONT SEAT TYPE 07 or FRONT SEAT TYPE 08
a Refit:
- the front seat base casings (see 77A, Front seat
trim, Front seat lower cover: Removal - Refit-
ting, page 77A-9) ,
- the front seat (see 75A, Front seat frames and
mechanisms, Complete front seat: Removal -
Refitting, page 75A-28) ,
- the front seat headrest (see 79A, Seat compo-
nents, Front headrest: Removal - Refitting,
page 79A-3) .
a Connect the battery (see Battery : Removal - Refit-
ting) (80A, Battery).
75A-16
FRONT SEAT FRAMES AND MECHANISMS
Front seat sliding motor: Removal - Refitting 75A
FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
Essential equipment
diagnostic tool
Note:
The front seat runner motor can be replaced
without removing the front seat.
REMOVAL
138016
138014
a Unclip the long cable (3) .
a Disconnect the connectors (1) from the front seat sli-
a Remove the « front seat slide motor - long cable »
de motor.
assembly.
75A-17
FRONT SEAT FRAMES AND MECHANISMS
Front seat sliding motor: Removal - Refitting 75A
FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
REFITTING
138015
a Unclip the short cable at (4) .
a Remove the short cable.
135100
135099
WARNING
To prevent any risk of de-synchronisation or loc-
king of the runners, check the condition of the
ends of the drive cables.
Any damaged cable (frayed) must always be
replaced.
75A-18
FRONT SEAT FRAMES AND MECHANISMS
Front seat sliding motor: Removal - Refitting 75A
FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
- display the « Before/After repair procedure » for
the computer selected,
- select « Driver's seat slide motor » ,
- carry out the operations described in the « After re-
pair procedure » section.
a Carry out a function test.
134068
Note:
An incorrectly fitted cable risks causing de-syn-
chronisation of the seat runners.
a Refit:
- the front seat slide motor,
- the long cable fully into the runner mechanism,
- the rigid clip.
a Connect the connectors to the front seat slide motor.
75A-19
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjustment motor: Removal - Refitting 75A
FRONT SEAT TYPE 04
REMOVAL
138034
a
Note:
The engine height adjustment mountings (self
lock type) cannot be removed.
The Parts Department supplies the front seat
frame assembled with the front seat height
adjustment motor.
75A-20
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt control: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
REMOVAL
137996
a Remove the elastic securing straps of the front seat-
back cover.
75A-21
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt control: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
II - OPERATION FOR REMOVAL OF PART
CONCERNED
137998
138001
a Disconnect the battery (see Battery : Removal -
Refitting) (80A, Battery).
a Unclip the front seatback angle control using the tool
(Car. 1363).
139293
Note:
Pull the front seatback angle control slightly
when unlocking the clips.
75A-22
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt control: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
137999
75A-23
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting 75A
B95 or D95, and FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
REMOVAL
138059
a Unclip the support of the rear seat access rotary
switch using the tool (Car. 1363).
75A-24
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting 75A
B95 or D95, and FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
II - OPERATION FOR REMOVAL OF PART
CONCERNED
138060
a Remove the bolt from the front seatback angle mo-
138055
tor.
a Remove:
- the "claw shaft" clip,
- the mounting from the front seat base interior ca-
sing.
138057
75A-25
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting 75A
B95 or D95, and FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
II - REFITTING OPERATION FOR PART
CONCERNED
138054
75A-26
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt motor: Removal - Refitting 75A
B95 or D95, and FRONT SEAT TYPE 04 or FRONT SEAT TYPE 07
a Refit the front seat lumbar adjustment control (see
Front seat lumbar adjustment control: Removal -
Refitting) .
a Refit the front seat base casings (see 77A, Front
seat trim, Front seat lower cover: Removal - Re-
fitting, page 77A-9) .
D95
a Refit the rear seat access control (see Rear seat ac-
cess control: Removal - Refitting) .
a Refit:
- the front seat headrest guides (see 79A, Seat
components, Front seat headrest guide: Remo-
val - Refitting, page 79A-7)
- the front seat (see 75A, Front seat frames and
mechanisms, Complete front seat: Removal -
Refitting, page 75A-28)
- the front seat headrest (see 79A, Seat compo-
nents, Front headrest: Removal - Refitting,
page 79A-3)
a Connect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
75A-27
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
Tightening torquesm
REMOVAL
a Adjust:
136727
a Unclip the front seat belt using a flat-blade screwdri-
ver.
139314
75A-28
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
Driver's side
139317 139316
a Tighten in the order indicated (1) , (2) , (3) , (4) .
a Tilt the front seat backwards.
Passenger side
Note:
Hold the wiring mounting to avoid breaking its
indexing guide (1) , when disconnecting the con-
nector from the front seat wiring.
REFITTING
II - REFITTING OPERATION FOR PART a Tighten in the order indicated (1) , (2) , (3) , (4) .
CONCERNED a Torque tighten the new front seat bolts (35 N.m).
75A-29
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
B95 or D95 or E95 or J95 or K95
75A-30
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seatback: Removal - Refitting 76A
B95 or D95, and REAR BENCH SEAT
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
REMOVAL
136693
a Remove the bolts (2) from the rear bench seatback.
136713
a Remove the rear seat belt buckle bolt (1) .
136697
a Remove the single unit rear bench seatback (3) then
(4) (this operation requires two people).
76A-1
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seatback: Removal - Refitting 76A
B95 or D95, and REAR BENCH SEAT
REFITTING
II - FINAL OPERATION
a Refit the rear seat belt buckle bolt.
a Torque tighten the rear seat belt buckle bolt (21
N.m).
a Refit:
- the single unit rear bench seat base,
- the rear section of the luggage compartment car-
pet.
76A-2
REAR SEAT FRAMES AND MECHANISMS
1/3 and 2/3 rear bench seatback: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
REMOVAL
136693
136713
a Remove the rear seat belt buckle bolt (1) .
142703
a Remove the bolts (2) from the central and side
mounting bracket of the rear bench seatback.
76A-3
REAR SEAT FRAMES AND MECHANISMS
1/3 and 2/3 rear bench seatback: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
142704 136687
a Release the rear bench seatback from the anti-re- a Separate the 1/3 and 2/3 rear bench seatbacks.
lease pins at (3) .
a Remove the rear bench seatback at (4) (this opera- REFITTING
tion requires two people).
76A-4
REAR SEAT FRAMES AND MECHANISMS
1/3 and 2/3 rear bench seatback: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
76A-5
REAR SEAT FRAMES AND MECHANISMS
Single unit rear bench seat: Removal - Refitting 76A
B95 or D95, and REAR BENCH SEAT
REMOVAL REFITTING
II - FINAL OPERATION
a Pull down the single unit rear bench seat seat base.
136700
a Tilt the single unit rear bench seat base.
136702
a Remove the single unit rear bench seat base.
76A-6
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback frame 1/3 and 2/3: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REFITTING
76A-7
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat mechanism: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT +
ARMREST + N/R SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
REMOVAL
a Remove:
- the rear bench seat headrests (see 79A, Seat
components, Rear headrest: Removal - Refit-
ting, page 79A-13) ,
a Remove: a Remove:
- the rear bench seatback (see 76A, Rear seat fra- - the bolts (1) of the rear bench seatback locking me-
mes and mechanisms, Single unit rear bench chanism,
seatback: Removal - Refitting, page 76A-1) , - the rear bench seatback locking mechanism. (2)
- the cover of the rear bench seatback (see 78A,
Rear seat trim, Rear bench seat single unit REFITTING
seatback trim: Removal - Refitting, page 78A-
11) .
I - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
- the rear bench seatback locking mechanism (2) ,
1-2/3 REAR BENCH SEAT + ARMREST + N/R
SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH - the bolts (1) of the rear bench seatback locking me-
RECLINING SEATBACK chanism.
a Remove: a Torque tighten the bolts of the rear bench seat-
back locking mechanism (18 N.m) (1) .
- the rear bench seatback (see 76A, Rear seat fra-
mes and mechanisms, 1/3 and 2/3 rear bench
seatback: Removal - Refitting, page 76A-3) , II - FINAL OPERATION
- the rear centre armrest (see 79A, Seat compo-
nents, Rear centre arm rest: Removal - Refit- 1-2/3 REAR BENCH SEAT + ARMREST + N/R
ting, page 79A-8) , SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH
- the cover of the rear bench seatback (see 78A, RECLINING SEATBACK
Rear seat trim, 1/3 and 2/3 rear bench seat seat- a Remove:
back trim: Removal - Refitting, page 78A-4) .
- the cover of the rear bench seatback (see 78A,
Rear seat trim, 1/3 and 2/3 rear bench seat seat-
back trim: Removal - Refitting, page 78A-4) ,
76A-8
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat mechanism: Removal - Refitting 76A
B95 or D95 or K95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT +
ARMREST + N/R SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
- the rear centre armrest (see 79A, Seat compo-
nents, Rear centre arm rest: Removal - Refit-
ting, page 79A-8) ,
- the rear bench seatback (see 76A, Rear seat fra-
mes and mechanisms, 1/3 and 2/3 rear bench
seatback: Removal - Refitting, page 76A-3) .
a Refit:
- the rear bench seat headrest guides (see 79A,
Seat components, Rear seat headrest guide:
Removal - Refitting, page 79A-9) ,
- the rear bench seat headrests (see 79A, Seat
components, Rear headrest: Removal - Refit-
ting, page 79A-13) .
a Carry out a function test.
76A-9
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat single-unit seatback frame: Removal - Refitting 76A
B95 or D95, and REAR BENCH SEAT
REMOVAL - the single unit rear bench seatback (see 76A, Rear
seat frames and mechanisms, Single unit rear
bench seatback: Removal - Refitting, page 76A-
OPERATION FOR REMOVAL OF PART 1) ,
CONCERNED
- the rear headrests (see 79A, Seat components,
a Remove: Rear headrest: Removal - Refitting, page 79A-
13) ,
- the rear headrests (see 79A, Seat components,
Rear headrest: Removal - Refitting, page 79A-
13) ,
REFITTING
a Refit:
76A-10
REAR SEAT FRAMES AND MECHANISMS
Second row complete rear seat: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
Tightening torquesm
REMOVAL
141416
141417
a Remove the side trims (1) and (2) of the rear floor.
141415
a Remove the rear floor rear trim.
76A-11
REAR SEAT FRAMES AND MECHANISMS
Second row complete rear seat: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
141412
141535
a Remove the lower nuts (5) from the seat belt strap of
the second row rear seats.
141488
a Unclip the second row rear seatback casings at (3)
then at (4) .
76A-12
REAR SEAT FRAMES AND MECHANISMS
Second row complete rear seat: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
- the anti-release bolts of the second row rear seat.
141413
141414
a
a Remove:
Note:
- the bolts (8) of the second row rear seat,
If the second row rear seat release strap is faulty,
- the second row rear seat module.
pull directly on the linkage to unlock the second
row rear seat.
Note:
The second row rear seat module weighs
approximately 40 Kg.
A second person is required to remove the
second row rear seat module.
141489
a Remove:
76A-13
REAR SEAT FRAMES AND MECHANISMS
Second row complete rear seat: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
REFITTING
141439
a Position the second row rear seat module on the
side supports of the second row rear seat with the
help of a second person.
Note:
The module of the second row rear seat is cen-
tred using the indexing guide (9) .
76A-14
REAR SEAT FRAMES AND MECHANISMS
Second row complete rear seat: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
141418
a Tighten the following in the order indicated: - the rear floor rear trim (see 71A, Body internal
trim, Floor carpet: Removal - Refitting, page
- the mountings of the second row rear seats on the 71A-1) ,
body (10) , (11) , (12) , (13) , (14) , (15) , (16) , (17) ,
- the rear wheel arch trims (see 71A, Body internal
- the anti-release bolts of the second row rear seat trim, Rear wheel arch lining: Removal - Refit-
(18) . ting, page 71A-33) ,
a Tighten to torque: - the rear end panel trim (see 71A, Body internal
- the mountings of the second row rear seat on trim, Rear end panel lining: Removal - Refitting,
the body (44 N.m), page 71A-60) .
II - FINAL OPERATION
a Torque tighten the lower nut of the second row
rear seat belt strap (44 N.m).
a Clip on the seatback casings.
a Refit:
- the rear floor side trims (see 71A, Body internal
trim, Floor carpet: Removal - Refitting, page
71A-1) ,
76A-15
REAR SEAT FRAMES AND MECHANISMS
Second row rear seat frame: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
Tightening torquesm
REMOVAL
141419
a Remove:
- the seatback release strap (2) ,
- the seat base pad (3) .
141533
a Remove the rivets (1) on the second row rear seat
frame.
76A-16
REAR SEAT FRAMES AND MECHANISMS
Second row rear seat frame: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
141423 141425
141424 141426
a Remove the bolts (4) from the second row rear seat a Remove:
on the cross member.
- the bolt (6) ,
- the second row rear seat base casing at (7) .
Note:
The compensation spring is no longer tensioned
when the second row rear seats are in the unfol-
ded position.
76A-17
REAR SEAT FRAMES AND MECHANISMS
Second row rear seat frame: Removal - Refitting 76A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
II - REFITTING OPERATION FOR PART
CONCERNED
a Refit:
a Tighten to torque:
- the second row rear seat. - the second row rear seat base casing (7) ,
- the bolt (6) of the second row rear seat base ca-
sing,
a Refit:
- the front side support (10) of the second row rear a Refit:
seat.
- the second row rear seat trim (see 78A, Rear seat
trim, Second row rear seat trim: Removal - Re-
REFITTING fitting, page 78A-16) ,
76A-18
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
B95 or D95
REMOVAL
a Remove:
118675
a Remove the retaining section.
137996
77A-1
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
B95 or D95
138154
a Disconnect the heated pad connector.
127480
a Remove the front seat base cover.
a
WARNING
When separating the "foam - cover", hold the vel-
cro strips.
REFITTING
138019 Note:
a Remove the clip using the tool (Car. 1363) at 2. Before refitting the front seat base trim, check
that the velcro strips are correctly attached to the
a Remove the retaining sections. foam.
a Remove the "foam - cover" assembly of the front
seat base.
77A-2
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
B95 or D95
II - REFITTING OPERATION FOR PART
CONCERNED
138022
a Refit:
- the front seat base cover,
- the "foam - cover" assembly of the front seat base,
a Refit:
- the clips,
77A-3
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
B95 or D95
II - OPERATION FOR REMOVAL OF PART
Essential special tooling CONCERNED
Car. 1363 Set of trim removal levers.
REMOVAL
D95
a Remove the rear seat access control (see Rear seat
access mechanisms: Removal - Refitting) .
138029
a Unclip the side retaining sections of the front seat-
back cover.
77A-4
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
B95 or D95
138154
a Disconnect the connector from the front seat heated
pad.
138030
a Remove the upper retaining sections of the front
seatback cover using the tool (Car. 1363).
138025
138031
a Remove:
a Remove the lower retaining section of the front seat-
back cover using the tool (Car. 1363). - the cover partially,
- the chest-level airbag (see Front (chest) side air-
bag: Removal - Refitting) (88C, Airbags and pre-
tensioners).
77A-5
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
B95 or D95
138155 138022
a Remove the front seatback cover.
a Align the velcro strips with the marks.
WARNING
To prevent any risk of damaging the foam when Note:
separating "foam - cover", hold the velcro strips. The pre-markings on the foam are a guide for
positioning the ends of the velcro strips.
REFITTING
Note:
Before refitting the front seatback cover, check
that the velcro strips are correctly attached to the
foam.
138028
77A-6
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
B95 or D95
138027 138024
a Position the front seatback cover over the foam, a Position the front seatback cover on the side velcro
starting with the side velcro strips (on the chest-level strips.
airbag side).
a Check that there are no folds.
138026
a Position the front seatback cover on the central vel- 138032
cro strips.
a Refit the exterior side profiles.
77A-7
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
B95 or D95
a Clip:
D95
a Refit the rear seat access control (see Rear seat ac-
cess mechanisms: Removal - Refitting) .
II - FINAL OPERATION
a Refit:
77A-8
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
B95 or D95
II - OPERATION FOR REMOVAL OF PART
Essential special tooling CONCERNED
Car. 1363 Set of trim removal levers.
1 - Front seat base interior casing
REMOVAL
138045
a Unclip the front seat base interior casing (2) .
137996
a Remove the elastic straps (1) from the front seat-
back cover.
138044
a
Note:
Replace the clip if deteriorated.
77A-9
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
B95 or D95
2 - Front seat base exterior casing
138010
138011
a Remove the bolts (3) and (4) from the front seat
base exterior casing.
a Unclip the front seat base exterior casing.
77A-10
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
B95 or D95
138046
a Disconnect the connectors (5) and (6) from the front
seat control unit.
a Unclip the controls from the front seat control unit
using the tool (Car. 1363).
138048
REFITTING
77A-11
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
B95 or D95
a Clip on the mounting clip for the wiring of the front
seat heated pad.
II - FINAL OPERATION
a Refit the elastic strap of the front seatback trim.
a Refit the front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Removal
- Refitting, page 75A-28) .
a Connect the battery (see Battery : Removal - Refit-
ting) (80A, Battery).
a Carry out a function test.
77A-12
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
II - OPERATION FOR REMOVAL OF PART
Essential special tooling CONCERNED
Car. 1363 Set of trim removal levers.
1 - Front seat interior casing
REMOVAL
a - Front seatback interior casing
139301
a Remove the blanking cover from the front seatback
interior casing using the tool (Car. 1363).
77A-13
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
139302 139304
a Remove the bolt (1) from the top section of the front a Remove the bolt from the front seatback interior ca-
seatback interior casing. sing.
139303 139305
a Remove the top section of the front seatback interior a Remove the front section of the front seatback inte-
casing at (2) and (3) . rior casing at (4) and (5) .
77A-14
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
139412 138044
a Remove the rear section of the front seatback inte- a
rior casing.
Note:
Replace the clip if deteriorated.
138045
a Unclip the front seatback interior casing.
139307
a Remove the bolt (6) from the front seat base interior
casing.
77A-15
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
2 - Front seat exterior casing
139308
a Unclip the front seat base interior casing at (7) and
(8) .
139295
139296
a Carefully unclip the control for positioning the front
seatback in the table position using a flat-blade
screwdriver.
Note:
It is difficult to access the locking clip. If the con-
trol for positioning the front seatback in the table
position is damaged, always replace the control.
77A-16
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
139297 139299
a Remove the blanking cover using the tool (Car. a Remove the front seatback exterior casing (10) .
1363).
139298
a Remove the bolt (9) .
141496
a Remove the blanking cover (11) from the front seat
lap belt pretensioner using the tool (Car. 1363).
77A-17
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06 FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06,
and FRONT SEAT WITH HEATING
141494
a Remove the bolts (12) from the front seat base exte-
rior casing.
141495
a Disconnect the connector for the front seat heated
pad and check that the clip is in good condition.
141493
a Remove:
- the front seat height adjustment control bolts (13) ,
- the front seat height adjustment control at (14) .
141526
a Remove the bolts (15) from the front seat lower ca-
sing.
77A-18
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
141524
a Remove:
141536
- the front seat height adjustment control bolts (16) ,
a Remove the bolts (18) from the electric front seat
- the front seat height adjustment control at (17) . lower casing.
141520
a Remove:
- the electric front seat lower casing,
- the electric front seat adjustment connectors (19) .
141529
77A-19
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
I - REFITTING OPERATION FOR PART FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06
CONCERNED
a Refit:
a Refit:
a Refit:
a Refit the bolt (6) for the front seat base interior ca-
sing.
77A-20
FRONT SEAT TRIM
Front seat lower cover: Removal - Refitting 77A
J95
b - Front seatback interior casing
a Refit:
- the bolt (1) for the top section of the front seatback
interior casing,
II - FINAL OPERATION
77A-21
REAR SEAT TRIM
1/3 and 2/3 rear bench seat trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REMOVAL
a Remove the rear bench seat bases (see 1/3 and 2/3
rear bench seat:Removal - Refitting) .
137412
a Remove the cover (2) of the 1/3 and 2/3 rear bench
seat base.
WARNING
To avoid any risk of damaging the foam, separate
the cover from the foam by holding the velcro
strips.
137437
137416
a Remove:
78A-1
REAR SEAT TRIM
1/3 and 2/3 rear bench seat trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REFITTING
WARNING
I - REFITTING PREPARATION OPERATION To avoid any risk of the cover detaching or any
folds in the cover, check that the velcro strips are
Incorrect secure on the foam. If the velcro strip tears,
replace the foam.
142781
Correct 142780
Note:
The markings on the foam are a guide for positio-
ning the velcro strips.
a Align the ends of the velcro strips with the marks (3) .
a Refit:
142779
a Check that the velcro strips are properly fastened on - the « foam - cover » assembly of the 1/3 and 2/3
the foam. rear bench seat base,
78A-2
REAR SEAT TRIM
1/3 and 2/3 rear bench seat trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
III - FINAL OPERATION
a Refit the rear bench seat bases (see 1/3 and 2/3
rear bench seat:Removal - Refitting) .
78A-3
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
Tightening torquesm
REMOVAL
142782
a Unclip the trims from the unlocking control of the
rear bench seatback using the tool (Car. 1363).
78A-4
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
1 - 1/3 rear bench seatback cover
136681
137422
a Remove:
- the bolt (3) ,
- the trim of the rear centre seat belt strap guide.
78A-5
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REAR BENCH FUNCTION or 1-2/3 REAR BENCH 1/3-2/3 REAR BENCH SEAT WITH RECLINING
SEAT + ARMREST + N/R SEATBACK SEATBACK
142785 142784
142808 142790
a Remove: a Remove:
- the rear bench seat supports. - the rear bench seat supports.
78A-6
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1-2/3 REAR BENCH SEAT + ARMREST + N/R
SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH
RECLINING SEATBACK
137424
a Extract the zip fasteners (5) .
a Open the zip fasteners.
a Remove the clips (6) .
142788
142789
78A-7
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
a Remove the rear bench seat headrest guides (see 2/3 bench seatback cover
79A, Seat components, Rear seat headrest gui-
de: Removal - Refitting, page 79A-9) .
a Remove the « cover - foam » assembly of the rear
bench seatback.
142787
142786
WARNING
To avoid any risk of damaging the foam, separate
the cover from the foam by holding the velcro
strips.
78A-8
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REFITTING
WARNING
I - REFITTING PREPARATION OPERATION To avoid any risk of the cover detaching or any
folds in the cover, check that the velcro strips are
Incorrect secure on the foam. If the velcro strip tears,
replace the foam.
142781
Correct 142780
Note:
The markings on the foam are a guide for positio-
ning the velcro strips.
a Align the ends of the velcro strips with the marks (8) .
142779 a Refit:
a Check that the velcro strips are properly fastened on
- the « cover - foam » assembly of the rear bench
the foam.
seatback,
78A-9
REAR SEAT TRIM
1/3 and 2/3 rear bench seat seatback trim: Removal - Refitting 78A
B95 or D95 or K95, and REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
a Refit:
1-2/3 REAR BENCH SEAT + ARMREST + N/R - the rear headrests (see 79A, Seat components,
SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH Rear headrest: Removal - Refitting, page 79A-
RECLINING SEATBACK 13) ,
- the rear bench seatbacks (see 76A, Rear seat fra-
2/3 rear bench seatback cover mes and mechanisms, 1/3 and 2/3 rear bench
seatback: Removal - Refitting, page 76A-3) ,
a Clip on the clip (7) .
- the rear bench seat bases (see 1/3 and 2/3 rear
bench seat:Removal - Refitting) .
78A-10
REAR SEAT TRIM
Rear bench seat single unit seatback trim: Removal - Refitting 78A
B95 or D95, and REAR BENCH SEAT
REMOVAL
137421
a Remove the seatback side mountings (1) .
137435
a Remove the bench seat lock trims (3) in order to tilt
the seatback.
78A-11
REAR SEAT TRIM
Rear bench seat single unit seatback trim: Removal - Refitting 78A
B95 or D95, and REAR BENCH SEAT
137424 137419
a Open the zip fasteners (4) . a Separate the single unit rear bench seat seatback
trim from the foam.
a Remove the clips (5) .
a Remove the trim from the seatback of the single unit
rear bench seat.
Note:
When separating the « trim - foam » , hold the
Velcro strips.
REFITTING
Note:
Check that the velcro strips still have sufficient
grip before refitting the seatback trim.
137432
a Refit:
a Remove the headrest guides (6) . - the single unit rear bench seatback trim,
a Partially remove the « trim - foam » assembly of the - the « trim - foam » assembly onto the bench seat-
single unit rear bench seatback. back frame,
- the headrest guides,
- the clips.
a Close the zip fasteners.
a Refit:
- the bench seat lock trims,
78A-12
REAR SEAT TRIM
Rear bench seat single unit seatback trim: Removal - Refitting 78A
B95 or D95, and REAR BENCH SEAT
- the seat belt trim,
- the seatback side mountings.
II - FINAL OPERATION
a Refit:
- the single unit rear bench seatback (see 76A, Rear
seat frames and mechanisms, Single unit rear
bench seatback: Removal - Refitting, page 76A-
1) ,
- the single unit rear bench seat base (see 76A,
Rear seat frames and mechanisms, Single unit
rear bench seat: Removal - Refitting, page 76A-
6) .
- the rear headrests (see 79A, Seat components,
Rear headrest: Removal - Refitting, page 79A-
13) .
78A-13
REAR SEAT TRIM
Rear bench seat single unit seat base trim: Removal - Refitting 78A
B95 or D95, and REAR BENCH SEAT
REMOVAL
137419
a Remove the single unit rear bench seat base trim (1)
.
137418 Note:
a Remove:
When separating the « foam - trim » , hold the
- the retaining sections, velcro strips.
Note:
Before refitting the single unit rear bench seat
base trim, check that the velcro strips are cor-
rectly attached to the foam.
a Refit:
78A-14
REAR SEAT TRIM
Rear bench seat single unit seat base trim: Removal - Refitting 78A
B95 or D95, and REAR BENCH SEAT
III - FINAL OPERATION
a Refit the single unit rear bench seat base (see 76A,
Rear seat frames and mechanisms, Single unit
rear bench seat: Removal - Refitting, page 76A-6)
.
78A-15
REAR SEAT TRIM
Second row rear seat trim: Removal - Refitting 78A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
REMOVAL
a Remove:
141433
a Remove the front (1) , side (2) and rear (3) retaining
sections of the third row rear seat base using the tool
(Car. 1363).
WARNING
To prevent any risk of damaging the foam when
separating the "cover - foam", hold the velcro
strips.
78A-16
REAR SEAT TRIM
Second row rear seat trim: Removal - Refitting 78A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
2 - SEATBACK TRIM
141435
141437 a Remove the elastic straps (7) .
WARNING
To prevent any risk of damaging the foam when
separating the "cover - foam", hold the velcro
strips.
141436
141434
a Remove:
a Remove:
- the bolt (4) of the locking mechanism trim,
- the cover,
- the locking mechanism trim at (5) .
- the foam.
a Check that the attachment bracket (6) of the locking
mechanism trim is in good condition.
a Remove the rear retaining sections of the second
row rear seat.
a Remove the second row rear seat headrest guides
(see 79A, Seat components, Rear seat headrest
guide: Removal - Refitting, page 79A-9) .
78A-17
REAR SEAT TRIM
Second row rear seat trim: Removal - Refitting 78A
J95, and LONG CHASSIS, and 2 SEATS 3RD ROW
1 - SEATBACK TRIM
141432
a
Note:
If the velcro strip (9) of the foam tears, always
replace the foam.
141430
a a Refit:
If the velcro strip (8) of the foam tears, always - the cover,
replace the foam. - the front, side and rear retaining sections of the se-
cond row rear seat base.
a Refit:
- the foam, II - FINAL OPERATION
- the cover, a Refit:
- the elastic straps (7) , - the second row rear seat rear headrest,
- the second row rear seat headrest guides (see - the second row rear seat module (see 76A, Rear
79A, Seat components, Rear headrest: Remo- seat frames and mechanisms, Second row
val - Refitting, page 79A-13) , complete rear seat: Removal - Refitting, page
- the rear retaining sections of the second row rear 76A-11) .
seat,
- the locking mechanism trim,
- the bolt (4) of the locking mechanism trim.
78A-18
SEAT COMPONENTS
Seatback tray: Removal - Refitting 79A
J95
REMOVAL
139312
139313
a Drill out the rivets of the front seatback parcel shelf.
Note:
To prevent any risk of damaging the covers and
mechanisms, recover any metal residues when
cutting the seat trim clips or drilling out the rivet.
139311
a Remove the front seatback parcel shelf at (1) and (2)
.
REFITTING
79A-1
SEAT COMPONENTS
Seatback tray: Removal - Refitting 79A
J95
II - REFITTING OPERATION FOR PART
CONCERNED
a Refit the front seatback parcel shelf.
79A-2
SEAT COMPONENTS
Front headrest: Removal - Refitting 79A
REMOVAL
Note:
The front seat headrest has an integrated con-
trol.
139290
139291
a Press the unlocking button on each headrest guide.
Note:
Depending on the type of unlocking button, this
operation is performed manually or using a flat-
blade screwdriver.
79A-3
SEAT COMPONENTS
Front headrest: Removal - Refitting 79A
Headrest rods misaligned
142683
139292
a Remove the front seat headrest.
REFITTING
IMPORTANT
To avoid any risk of incorrectly positioning the
rods of the front seat headrest, align the rods
before inserting them in the headrest guides.
142684
a Insert the rods of the front seat headrest in the hea-
drest guides.
a Push the front seat headrest until it locks into place
with the locking notches then adjust the front seat
headrest to the low position.
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
79A-4
SEAT COMPONENTS
Heated seat cover: Removal - Refitting 79A
FRONT SEAT WITH HEATING
Front seatback
133734
a Carefully detach the heated seat pad.
WARNING
To avoid any damage to the foam, detach the
heated pad carefully.
79A-5
SEAT COMPONENTS
Heated seat cover: Removal - Refitting 79A
FRONT SEAT WITH HEATING
79A-6
SEAT COMPONENTS
Front seat headrest guide: Removal - Refitting 79A
B95 or D95 or E95 or J95 or K95
REMOVAL REFITTING
Note: Note:
The headrest guides can be removed without To prevent the headrest guides from being mixed
removing the front seatback cover. up, each headrest guide has a specific indexing
device.
II - OPERATION FOR REMOVAL OF PART a Check that the headrest guides are secure in the
CONCERNED front seatback frame.
II - FINAL OPERATION
a Refit the front seat headrest (see 79A, Seat compo-
nents, Front headrest: Removal - Refitting, page
79A-3) .
a Carry out a function test.
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
139289
a Slightly detach the "foam - cover" assembly of the
seatback near the headrest guides to reveal the
front seat headrest guide clips.
a Unclip the front seat headrest guides using a flat-
blade screwdriver.
a Remove the front seat headrest guides.
Note:
The clips of the front seat headrest guides are all
on the same side.
79A-7
SEAT COMPONENTS
Rear centre arm rest: Removal - Refitting 79A
B95 or D95, and 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
REMOVAL REFITTING
II - FINAL OPERATION
a Position the 1/3 rear bench seat (1) .
134165
134166
a Remove:
79A-8
SEAT COMPONENTS
Rear seat headrest guide: Removal - Refitting 79A
B95 or D95 or K95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT +
ARMREST + N/R SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
a Remove:
- the rear bench seat base (see 76A, Rear seat fra-
mes and mechanisms, Single unit rear bench
seat: Removal - Refitting, page 76A-6) ,
a Remove:
- the rear bench seat base (see 1/3 and 2/3 rear
bench seat:Removal - Refitting) ,
79A-9
SEAT COMPONENTS
Rear seat headrest guide: Removal - Refitting 79A
B95 or D95 or K95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT +
ARMREST + N/R SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
REFITTING a Refit the rear bench seat headrests (see 79A, Seat
components, Rear headrest: Removal - Refitting,
page 79A-13) .
I - REFITTING OPERATION FOR PART
CONCERNED
IMPORTANT
a Refit the rear bench seat headrest guides fully into To prevent the headrest coming away from the
the rear seat frame. guide during a collision, check that headrest
guide locking system is functioning correctly.
a Check that the rear bench seat headrest guides are
secure on the rear seat frame.
II - FINAL OPERATION
a Refit:
- the rear bench seat base (see 1/3 and 2/3 rear
bench seat:Removal - Refitting) .
a Refit:
- the rear bench seat base (see 76A, Rear seat fra-
mes and mechanisms, Single unit rear bench
seat: Removal - Refitting, page 76A-6) .
79A-10
SEAT COMPONENTS
Rear seat headrest guide: Removal - Refitting 79A
J95
141531
141412
a Remove the retaining sections (3) of the third row
rear seatback trim.
141488
a Remove:
- the third row rear seatback casing at (1) and (2) ,
- the third row rear seat headrest (see 79A, Seat
components, Rear headrest: Removal - Refit-
ting, page 79A-13) .
79A-11
SEAT COMPONENTS
Rear seat headrest guide: Removal - Refitting 79A
J95
REFITTING
Note:
The headrest guides are identical; it is possible
to mix them up.
II - FINAL OPERATION
a Refit:
- the third row rear seat headrest (see 79A, Seat
components, Rear headrest: Removal - Refit-
ting, page 79A-13) ,
- the third row rear seatback casing.
a Carry out a function test.
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
141490
a Unclip the third row rear seat headrest guides by
pinching the clips (4) .
a Remove the third row rear seat headrest guides.
79A-12
SEAT COMPONENTS
Rear headrest: Removal - Refitting 79A
B95 or D95 or J95 or K95
Note:
Depending on the type of unlocking button, this
operation is performed manually or using a flat-
blade screwdriver.
REMOVAL
137420
REFITTING
a Refit the rear seat headrest into the guides to the sa-
fety notch position.
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
79A-13
SEAT COMPONENTS
Rear bench seat headrest: Removal - Refitting 79A
B95 or D95 or K95, and REAR BENCH SEAT or REAR BENCH FUNCTION or 1-2/3 REAR BENCH SEAT +
ARMREST + N/R SEATBACK or 1/3-2/3 REAR BENCH SEAT WITH RECLINING SEATBACK
a Carry out a function test.
a Adjust the rear bench seat headrest to the low posi-
Note:
tion.
Depending on the type of unlocking button, this
operation is performed manually or using a flat-
blade screwdriver. IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
REMOVAL guide locking system is functioning correctly.
137420
a Press the unlocking buttons on each rear bench seat
headrest guide at (1) .
a Remove the rear bench seat headrest.
REFITTING
79A-14