Professional Documents
Culture Documents
AN7512SH
Dual 1-W BTL audio power amplifier
■ Overview Unit: mm
The AN7512SH is an audio power amplifier IC
14.00±0.10 Area of no resin flash
with surface mount package for stereo system. The (6.90)
BTL (Balanced Transformer-Less) method can pro- (5.45)
56 29 (1.00)
vide fewer external parts and more easy design for
0.15±0.05
applications.
6.10±0.10
8.10±0.20
(3.70)
(2.25)
■ Features 0° to 8°
0.50±0.10
1.20 max.
0.50
• On-chip standby function
(1.00)
(0.25) 0.20±0.05
0.10 M
0.10±0.10
• Small and thin surface mount package 0.10
■ Block Diagram
RL = 8 Ω VCC RL = 8 Ω
470 µF
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
TAB
Volume
Standby
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
68 kΩ
Standby 1 µF 1 µF Volume
270 kΩ 10 µF Off 5V 1.25 V
0V On 10 kΩ 10 kΩ 0V
VIN VIN
■ Pin Descriptions
Pin No. Description Pin No. Description
1 Standby (standby state if this pin is open.) 33 Ground (output ch.2)
9 Ch.1 input 37 Ch.2 + output
12 Ground (input) 42 TAB (tablet)
15 TAB (tablet) 45 Supply voltage
20 Ch.2 input 48 Ch.1 + output
28 Volume (muting off if this pin is open.) 52 Ground (output ch.1)
29 Ch.2 − output 56 Ch.1 − output
N.C. Pin No. 2, 3, 4, 5, 6, 7, 8, 10, 11, 13, 14, 16, 17, 18, 19, 21, 22, 23, 24, 25, 26, 27, 30, 31, 32, 34, 35, 36, 38,
39, 40, 41, 43, 44, 46, 47, 49, 50, 51, 53, 54, 55
Note) Please do not apply voltage or current to the N.C. pin from outside.
2 SDC00033BEB
AN7512SH
2 N.C.
3 N.C.
4 N.C.
5 N.C.
6 N.C.
7 N.C.
8 N.C.
SDC00033BEB 3
AN7512SH
1 kΩ
9
1 kΩ 1 kΩ 500 Ω
10 N.C.
11 N.C.
12 GND 0V
12
13 N.C.
14 N.C.
15 GND Connected to TAB
16 N.C.
17 N.C.
18 N.C.
19 N.C.
20 Ch.2 input pin VREF1 (1.4 V) 1.4 V
VCC (Input circuit
bias voltage is
50 µA 50 µA 100 µA
30 kΩ output.)
1 kΩ
20
1 kΩ 1 kΩ 500 Ω
4 SDC00033BEB
AN7512SH
1 kΩ
28 12 kΩ
200 Ω 50 Ω 29
1/2 VCC
800 Ω 20 kΩ
30 N.C.
31 N.C.
32 N.C.
33 GND 0V
33
34 N.C.
35 N.C.
36 N.C.
SDC00033BEB 5
AN7512SH
200 Ω 50 Ω 37
1/2 VCC
800 Ω 20 kΩ
38 N.C.
39 N.C.
40 N.C.
41 N.C.
42 GND Connected to TAB 0V
43 N.C.
44 N.C.
45 VCC 5.0 V
46 N.C.
47 N.C.
48 Ch.1 + output pin 2.15 V
VCC
(at no signal)
200 Ω 50 Ω 48
1/2 VCC
800 Ω 20 kΩ
49 N.C.
50 N.C.
51 N.C.
6 SDC00033BEB
AN7512SH
53 N.C.
54 N.C.
55 N.C.
56 Ch.1 − output pin VCC 2.15 V
(at no signal)
200 Ω 50 Ω 56
1/2 VCC
800 Ω 20 kΩ
■ Usage Notes
• Please avoid the short circuit to VCC , ground, or load short circuit.
• Please connect the cooling fin with the GND potential.
• The thermal shutdown circuit operates at about Tj = 150°C. However, the thermal shutdown circuit is reset automati-
cally if the temperature drops.
• Please carefully design the heat radiation especially when you take out high power at high VCC .
• Please connect only the ground for the signal input with the signal GND of the amplifier in the previous stage.
• Take notice that the ripple rejection ratio is poor in case of headphone use.
• Take notice that as to following pins, electric surge voltage is low.
At 200 pF, Pin1 = +140 V, Pin9 = +140 V, Pin20 = +130 V, Pin28 = +150 V.
• Use a speaker with 8 Ω or more impedance.
SDC00033BEB 7
AN7512SH
■ Technical Data
• PD Ta curve of HSOP056-P-0300A • Main characteristics
1.400
CT f
1.300 90
1.257
1.200 Mounted on standard board
(glass epoxy: 50 × 50 × t0.8 mm3) 80
1.100 Rth(j-a) = 79.5°C/W Ch.1
70
Power dissipation PD (W)
1.000
Ch.2
0.800 50
0.700 40
0.690 VCC = 5 V
0.600 PO = 0.25 W
Independent IC 30
RL = 8 Ω
0.500 without a heat sink
Rth( j-a) = 144.9°C/W Rg = 10 kΩ
20
0.400 VSTB = 5 V
Vol. = 1.25 V
0.300 10
0.200 0
10 100 1 000 10 000 100 000
0.100
Frequency f (Hz)
0.000
0 25 50 75 100 125
0 0 0
0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14
1 10
Supply current ICC (A)
Output power PO (W)
2.5
0.6
THD (ch.2, 10 kHz)
THD (ch.1, 10 kHz) 2.0
0.5
0.1 1
THD (ch.1, 100 kHz) 0.4
1.5
PC (8 Ω) 0.3
THD (ch.2, 100 kHz)
1.0
0.01 THD (ch.2, 1 kHz) 0.1 VCC = 5V Both ch. inputs
THD f = 1 kHz Rg = 10 kΩ 0.2
PO (ch.1, ch.2) (ch.1, 1 kHz)
RL = 8 Ω VSTB = 5 V
0.5
400 Hz HPF Vol. = 1.25 V 0.1
30 kHz LPF
0.001 0.01 0.0 0.0
1 10 100 1 000 0.0 0.5 1.0 1.5
8 SDC00033BEB
AN7512SH
25 0.0 0.01
10 100 1 000 10 000 100 000 10 100 1 000 10 000 100 000
30 kHz LPF 20
Voltage gain GV (dB)
RR VRIPPLE RR fRIPPLE
80 80
50 VCC = 5 V VSTB = 5 V 50
RL = 8 Ω Vol. = 0/1.25 V VCC = 5 V Vol. = 1.25 V
30 kHz LPF VRIPPLE = 0.5 V[rms] RL = 8 Ω VRIPPLE = 0.5 V[rms]
40 Rg = 10 kΩ fRIPPLE = 120 Hz 40 Rg = 10 kΩ fRIPPLE = 120 Hz
VSTB = 5V
Ch.2
30 Ch.2 30
20 20 Ch.1
Ch.1
10 10
0 0
10 100 1 000 10 000 10 100 1 000 10 000 100 000
Power supply ripple voltage VRIPPLE (mV[rms]) Power supply ripple frequency fRIPPLE (Hz)
SDC00033BEB 9
AN7512SH
Ch.2 (vol.-max.)
60 VSTB = 5 V
60 VRIPPLE = 0.5 V[rms]
RL = 8 Ω Vol. = 0 V/1.25 V
fRIPPLE = 120 Hz
30 kHz LPF VRIPPLE = 0.5 V[rms] 50
50 Rg = 10 kΩ fRIPPLE = 120 Hz Ch.2
VSTB = 5 V
40 40
Ch.2 Ch.1
30 30
Ch.1
20 20
10 10
0 0
0 2 4 6 8 10 12 14 0.0 0.2 0.4 0.6 0.8 1.0 1.2
VSTB = 5 V VSTB = 5 V
Vol. = 0 V/1.25 V Vol. = 0 V/1.25 V
600 600
500 500
Ch.1 (vol.-max.)
400 400 Ch.2 (vol.-max.)
0 0
0 2 4 6 8 10 12 14 10 100 1 000 10 000 100 000
Rg = 10 kΩ
800 Ch.1 (FLAT)
Vol. = 1.25 V
Quiscent circuit current ICQ (A)
Ch.2 (FLAT) 60
700
VCC = 5 V
600 RL = 8 Ω 50
Rg = 10 kΩ ICQ
500 DIN audio filter 40
VSTB = 5 V
400
30
300
20
200
Ch.1, Ch.2
100 10
0 0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0.0 0.5 1.0 1.5 2.0 2.5 3.0
10 SDC00033BEB
AN7512SH
90 90
Ch.2
Volume attenuation Att (dB)
70 70
PO = 0.25 W VCC = 5 V
f = 1 kHz f = 1 kHz
60 RL = 8 Ω 60 RL = 8 Ω
400 Hz HPF 400 Hz HPF
30 kHz LPF 30 kHz LPF
50 Rg = 10 kΩ 50 Rg = 10 kΩ
VSTB = 5 V VSTB = 5 V
Vol. = 0 V Vol. = 0 V
40 40
0 2 4 6 8 10 12 14 1 10 100 1 000
90 RL = 8 Ω VSTB = 5 V
Volume attenuation Att (dB)
Vol. = 1.25 V
85
1
80
Ch.1, Ch.2
75
Ch.2
70
VCC = 5 V
PO = 0.25 W 0.1
65 Ch.1
RL = 8 Ω
Rg = 10 kΩ
60
VSTB = 5 V
Vol. = 0 V
55
50 0.01
10 100 1 000 10 000 100 000 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4
CT VCC CT VIN
90 90
80 80
Ch.1 Ch.2
70 70
Ch.1
Cross talk CT (dB)
60 Ch.2 60
50 50
40 40
PO = 0.25 W VCC = 5 V
f = 1 kHz f = 1 kHz
30 30
RL = 8 Ω RL = 8 Ω
400 Hz HPF 400 Hz HPF
20 30 kHz LPF 20 30 kHz LPF
Rg = 10 kΩ Rg = 10 kΩ
10 VSTB = 5 V 10 VSTB = 5 V
Vol. = 1.25 V Vol. = 1.25 V
0 0
0 2 4 6 8 10 12 14 10 100 1 000
SDC00033BEB 11
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.
2001 MAR
This datasheet has been download from:
www.datasheetcatalog.com