Professional Documents
Culture Documents
PD 65394 GB5
2000-09
Application
CPMI-2 and CPMO-2 are sanitary constant-pressure
valves for use in stainless steel pipe systems.
Working principle
CPMI-2 and CPMO-2 are remote-controlled by means
of compressed air. The valves operate without a
transmitter in the product line and require only a
pressure regulating valve for the compressed air and
a pressure gauge in the product line (see fig. 4).
Standard design
The valve consists of a valve body with valve seat,
cover, a valve plug with a diaphragm unit and a clamp.
CPMI-2 CPMO-2
b. Increased product pressure.
Fig. 2. Principle.
Pressure drop/capacity diagrams
CPM-2, Kv 23
CPMO-2, Kv 23 CPMI-2, Kv 23
[%]
CPMI-2, Kv 7 CPMO-2, Kv 9
CPMI-2, Kv 7 CPMO-2, Kv 9
[%]
CPM-2, Kv 2/15
NOTE!
For the diagrams the following applies:
Medium: Water (200C).
[%] Measurement: In accordance with VDI 2173.
Example 1: Example 2:
Pressure drop D p = 200 kPa. CPMI-2:
Flow Q = 8 m3/h. Pressure drop D p = 300 kPa.
Select: CPM-2, Kv 23 which at working point Flow Q = 1 m3/h.
will be 48% open. Select: CPMI-2, Kv 2/15 which at working point will
be approx. 35% open equal to about 50% of the
regulating area.
Technical data
Max. product pressure: ...........................................................................1000 kPa (10 bar).
Min. product pressure: ............................................................................ 0 kPa (0 bar).
Temperature range: ................................................................................-10o C to + 95oC.
Temperature range with upper diaphragm in PTFE/EPDM: ....................-10o C to +140o C.
(Higher on request).
Materials
Product wetted steel parts: .....................................................................Acid-resistant steel AISI 316L.
Other steel parts: ....................................................................................Stainless steel AISI 304.
Finish: .....................................................................................................Semi-bright.
Lower diaphragm: ...................................................................................PTFE covered EPDM rubber.
Upper diaphragm: ...................................................................................Nitrile (NBR).
F
H
)
R1/4" (BSP
A1
A2
Dimensions (mm)
OD
ID
Kv 23 Kv 7 Kv 2/15 Kv 23 Kv 9 Kv 2/15
A1 175.1 175.1 175.1 211 175.1 175.1
M
A2 193.4 193.4 193.4 229.3 229.3 193.4 t
M
OD
ID (Inch/DIN) 47.6/50 47.6/50 47.6/50 47.6/50 47.6/50 47.6/50
G
t (Inch/DIN) 1.6/1.5 1.6/1.5 1.6/1.5 1.6/1.5 1.6/1.5 1.6/1.5
a. CPMI-2.
E (Inch/DIN) 49/50 49/50 49/50 89/86 49/50 49/50
F 18.3 18.3 18.3 18.3 18.3 18.3 H
F
G 110 110 110 110 110 110
H 203 203 203 203 203 203 )
R1/4" (BSP
M/ISO clamp 21 21 21 21 21 21
M/ISO male 21 21 21 21 21 21
M/DIN male 22 22 22 22 22 22
A1
A2
M/SMS male 20 20 20 20 20 20
OD
ID
M/BS male 22 22 22 22 22 22
Seat diameter 42 31 31 42 31 31
E
M
t
t
Air Connections
ID
R 1/4" (BSP), internal thread.
OD
G
b. CPMO-2.
Fig. 3. Dimensions.
Options
Equipment C
A) Male parts or clamp liners in accordance with re-
quired standard.
B) Available pressure gauges can be found in our D
Ordering Leaflet under Metering.
C) Air pressure regulating valve kit, 0-8 bar.
D) Air throttling valve for adjustment of regulating speed
for the CPM-2 valve.
E) Booster for product pressure exceeding the available
air pressure. (Product pressure = 1.8 x air
pressure).
Material grades
G) Upper diaphragm of PTFE covered EPDM and O-
ring of Fluorinated rubber (FPM) covered EPDM
rubber, (for temperature 95-140oC).
H) Both diaphragms of solid PTFE and O-ring of Fluori- Fig. 4. CPMI-2 with pressure regulating valve and pressure gauge.
nated rubber (FPM) (for temperatures above 140oC).
Ordering
Please state the following when ordering:
- Valve type. (CPMI-2 or CPMO-2).
- Plug size (Kv 23, Kv 7, Kv 9 or Kv 2/15).
- Diaphragm type if not standard.
- Connections if not welding ends.
- Options.