Professional Documents
Culture Documents
Spannungskonstanthalter
Stabilizzatore di tensione
Régulateur de tension
MAN01646Y/2
IREM SpA Via Abegg 75 - 10050 Borgone Torino Italy - tel. ++39 0119648211 - fax ++39 0119648222 - E-mail: irem@irem.it - www.irem.it
Technical characteristics
No. of phases 3 +N
Nominal input voltage [V] 400
Input voltage variation [%] ±15
Rated power [kVA] 15
Max. input current [A] 26
Rated current [A] 22
Response time [ms/Volt] 16
Nominal output voltage (true RMS stabilized ) [V] 400
Accuracy [%] ±1
Frequency [Hz] 50/60 ±5%
Admitted load variation [%] 0 to 100
Load power factor any
Harmonic distortion [%] <0,2
Efficiency [%] approx. 97
Cooling free convection
Operating temperature [°C] -10 to +40
Storage temperature [°C] -20 to +60
Relative humidity (without condensate) [%] 90
Degree of protection IP 21
Weight [kg] 117
Dimensions [mm] 535 x 410 x 1105h
MAN01646Y/2
3
Block diagram and operating principle
MAN01646Y/2
4
Installation and use
Install the voltage regulator in a dry and not dusty site, be sure that there is a free air flow
through the vents.
Before connecting the voltage regulator, check that it has not suffered any
damage during the transport, and check that the input voltage corresponds
to the one shown on the data plate.
The unit has no protection against short circuits and overloads, so:
The output line has been protected against possible short circuits by means of three 25A
rated fuses.
Connect the input line to the terminal board (10) (input terminals U1 V1 W1 N1) by
means of cables having a section suitable to the max. input current (26A).
Connect the output line to the terminal board (11) (output terminals U2 V2 W2 N2) by
means of cables having a section suitable to the max. output current (22A).
Connect the ground to the terminal marked PE (12) by means of a single-pole cable
suitable to the plant characteristics (see Standards EN 60439-1 and IEC 439-1).
MAN01646Y/2
5
Installation and use
400/230V 3PH+N
400V 3PH
Supply the voltage regulator and check on the voltmeter (2) the stabilized voltage
between two phases. Act on the voltmeter selector (3) to read the input and output line
voltage.
Warning !
When installing the regulator in presence of:
. loads having high inrush currents (e.g.: pumps, compressors, motors...)
. loads having numerous startings (lifts....)
. loads generating HF noises
. networks fed by electrical generating sets
some abnormal operating conditions may occur, if model and rating of the
regulator are incorrect.
MAN01646Y/2
6
Component layout
1) Control panel
2) Voltmeter
3) Voltmeter selector
4) Pilot lamp
5) Variable autotransformer
6) Servomotor
7) Brush
9) Series transformer
10) Input terminal board
11) Output terminal board
12) Ground terminal
15) Control board
16) Sensitivity trimmer
17) Zero setting trimmer
18) Power transformer
63) Output fuses
MAN01646Y/2
7
Troubleshooting
2. The single-phase unit is supplied but does not stabilize the output voltage:
- Check that there is no obstruction to the free movement of the brush (7) of the
variable autotransformer (5).
- Check the efficiency of the transmission between the servomotor (6) and the
variable autotransformer (5).
- Check the good operation of the servomotor (6) by disconnecting one of the two
wires and supplying it with 12Vdc approx.
- Check that on the secondary of the control circuit power transformer (18) there is
a voltage of 12Vac between terminals 2 and 3 and between terminals 2 and 1.
- If this is not sufficient, replace the control board (15).
3. The single-phase unit only operates at high input voltage or only at low input voltage:
- Check the good operation of S1-S2 microswitches (refer to the wiring diagram).
- Replace the control board (15).
4. The single-phase unit has a very high output voltage and the autotransformer brush
is at commutator end:
- Check that on the secondary of the control circuit power transformer (18) there is
a voltage of 12.5Vac between terminals 6 and 5.
- Replace the control board (15).
MAN01646Y/2
8
Troubleshooting
5. At no-load and in presence of an input voltage a little higher than the phase voltage,
the brush (7) of the variable autotransformer is at commutator end in one direction;
in presence of an input voltage a little lower than the phase voltage the brush is at
commutator end in the opposite direction. The output voltage is the same as the input
one:
- Make sure the tap of the variable autotransformer is not unsoldered (due to
overload). In this case, before re-soldering, check the variable autotransformer
(5) is not overheated or burnt. If it is, replace it.
- Check that the brush is in good conditions and touching without arcing the variable
autotransformer commutator.
- Check there is a good contact (without arcing) among the sliding contacts, the
brush holder cap and the output terminals of the variable autotransformer (5).
8. The output voltage is not within ±1% of the phase voltage but higher or lower:
- Reset the output voltage at the proper value by acting on the trimmer (17) placed
on the control board (15).
MAN01646Y/2
9
Troubleshooting
9. The brush (7) of the variable autotransformer (5) is badly worn or there is arcing:
- Disconnect the unit from the mains.
- Clean the tracks of the variable autotransformer making use of a cloth soaked into
alcohol (do not use any solvent).
- Remove the brush by disconnecting the cable and then loose the screw and the
nut from the plate
- Unfasten the brush assembly fixing screws and remove it
- Insert the new brush assembly
- Take in place the cable on the plate by tightening the screw, the nut and the
washer
- Verify the smooth movement of the brush into its holder by gently pulling upwards
the copper conductor.
- Verify that the brush fits flat over the entire surface.
Maintenance
The voltage regulator does not need particular maintenance or greasing of the moving
parts. However, every six months of operation, it is advisable to behave as follows:
- disconnect the unit from the mains
- clean the internal components
- check the brush may freely move on its slots or pins, is not badly worn and there is
no arcing.
If burning troubles are found:
- clean the tracks of the variable autotransformer without using solvents
- replace the brush as per section no. 9.
MAN01646Y/2
10
Technische Daten
Phasenanzahl 3+N
Nennspannung [V] 400
Eingangsspannungstoleranz [%] ±15
Leistung [kVA] 15
Eingangshöchststrom [A] 26
Ausgangshöchststrom 22
Regelgeschwindigkeit [ms/Volt] 16
Ausgangsspannung [V], RMS geregelt 400
Regelgenauigkeit [%] ±1
Nennfrequenz [Hz] 50/60 ±5%
zul. Laständerung [%] von 0 bis 100
Leistungfaktor der Last irgendeiner
Klirrfaktor [%] <0,2
Wirkungsgrad [%] ca. 97
Kühlung eigene Luftkühlung
Umgebungstemperatur [°C] -10 bis +40
Lagertemperatur [°C] -20 bis +60
relative Feuchtigkeit (ohne Kondensat) [%] 90
Schutzart IP21
Gewicht [kg] 117
Abmessungen [mm] 535 x 410x 1105
MAN01646Y/2
11
Blockschema und Funktionsprinzip
EINGANG AUSGANG
Reihen-
transformator
Stelltransformator
Vor dem Anschluß des Gerätes ist durch eine Sichtkontrolle zu überprüfen,
ob der Konstanthalter während des Transports beschädigt wurde, ob die
Spannung der Leitung, an die er angeschlossen wird dem Leistungsschild
entspricht.
Das Gerät ist nicht gegen Kurzschlüsse und Überlasten geschützt:
■ Kurzschlüsse : es ist erforderlich, dem Gerät Sicherungen oder einen
Die Ausgangsleitung ist vor Kurzschluß durch drei Sicherungen (25A) geschützt.
Der Klemme PE (12) durch ein einpoliges mit geeignetem Querschnitt Kabel an die Erde
der Anlage anschließen (siehe Vorschrifte EN 60439-1 und IEC 439-1).
MAN01646Y/2
13
Installation und Bedienung
Wichtig: Wenn der Nulleiter nicht vorhanden ist, soll ein Dreiphasen-
transformator mit den folgenden Eingenschaften vorgeschaltet werden:
Primär: 400V (Dreieckschaltung)
Sekundär: 400/230V (Sternschaltung mit Nulleiter)
Leistung des Spannungskonstanthalters: 15kVA
Leistung des Transformators: 18kVA
400/230V (3PH+N)
400V 3PH
Dem Gerät Spannung zuführen und auf dem Voltmeter (2) den Wert der stabilisierten
Spannung kontrollieren.
Achtung !
Sollte der Konstanthalter unter den folgenden Bedingungen installiert
werden:
. Lasten mit hohem Spitzenstrom (z.B. Pumpen, Kompressoren, große
Motoren, etc.)
. Lasten mit hoher Zahl von Anläufen (z.B. Aufzüge)
. Lasten die Hochfrequenzstörungen verursachen
. von Stromerzeugungsaggregat angetriebenes Netz
könnten sich schlechte Betriebskonditionen einstellen, wenn das Model
nicht genau ausgesucht und die richtige Leistung hat.
MAN01646Y/2
14
Komponentenaufbau
MAN01646Y/2
15
Störungssuche
2. Der Spannungskonstanthalter ist korrekt versorgt, stabilisiert aber nicht die Ausgangs-
spannung:
- Überprüfen, ob die Bürsten (7) funktionfähig sind und die Laufbahn des
Stelltransformators (5) gut berühren (ohne Funken zu verursachen).
- Überprüfen, ob die Übertragung zwischen den Servomotor (6) und den
Stelltransformator (5 funktioniert.
- Überprüfen, ob der Servomotor (6) funktionfähig sind. Zu diesem Zweck eins der
beiden Anschlußkabel entfernen und den Motor mit ca. 12V DC versorgen.
- Überprüfen, ob eine Spannung von ca. 12V AC zwischen Klemmen 2 und 3 und
zwischen Klemmen 2 und 1 an der Sekundärwicklung des Versorgungs-
transformators (18) vorhanden ist.
- Wenn die Kontrolle erfolglos sind, ist die Steuerkarte (15) auszutauschen.
4. Die Ausgangsspannung ist hoch und die Kohlenkontakte des Stelltransformators ist
am Grenze der Laufbahn:
- Überprüfen, ob eine Spannung von ca. 12,5V zwischen Klemmen 6 und 5 an der
Sekundärwicklung des Versorgungstransformator (18) vorhanden ist.
- Sollte dies nicht ausreichen, die Steuerkarte (15) ersetzen.
MAN01646Y/2
16
Störungssuche
5. Bei Nullast und wenn die Eingangsspannung ein bißchen höher als die Sternspannung
ist, sind die Bürsten (7) des Stelltransformators (5) am Grenze der Laufbahn in einer
Richtung; wenn die Eingangsspannung ein bißchen niedriger als die Sternspannung
ist, bleiben die Bürsten am Grenze der Laufbahn in der gegensätzlichen Richtung.
Die Ausgangsspannung ist die selbe wie im Eingang:
- kontrollieren, daß die Anzapfung am Stelltransformator (5) nicht abgeschweisst
ist (wegen Überlast). Wenn es der Fall ist, bevor sie wiederzuschweissen,
uberprüfen, ob die Kohlenbürsten (7) funktionfähig sind und die Laufbahn gut
berühren (ohne Funken zu verursachen).
- Überprüfen, ob es einen guten Kontakt (ohne Funken) zwischen den Kohlen-
bürsten, dem Bürstenhalter und dem Ausgangsklemmen des Stelltransformators
gibt.
8. Die Ausagangsspannung ist nicht bei ±1% der Sternspannung, sondern höher oder
niedriger:
- Die Ausgangsspannung auf den korrekten Wert durch Drehen des auf der Steuer-
karte (15) angeordneten Trimmers (17) einstellen.
MAN01646Y/2
17
Störungssuche
9. Die Kohlenbürsten (9) der Stelltransformatoren (10) sind verbraucht oder es sind
Funkenspuren auf der Kontaktbahn:
- Das Gerät vom Netz abschalten.
- Die Bahnen auf dem Stelltransformator mit einem Tuch reinigen, ohne dabei
Lösungsmittel zu verwenden,
Die Bürsten wie folgt austauschen:
- die Bürste von der Platte abschließen, indem Schrauben und Muttern gelöst
werden
- die Schrauben abnehmen und die Bürsten herausziehen
- die neue Bürste einsetzen und diese mit den Schrauben befestigen
- das Kabel mit Schrauben, Muttern und Scheiben auf der Platte befestigen
- die Bürste leicht von der Kontaktbahn abheben und ein sehr feines Schmirgelpapier
dazwischenschieben. Die Reibefläche muss zu der Bürste stehen.
- das Schmirgelpapier festhalten und den Bürstenhalter einige Male für einige
Grade drehen.
- Einige komplette Drehungen durchführen und sicherstellen, dass die Bürste
immer in Berührung mit der Kontaktbahn bleibt.
Wartung
Das Gerät bedarf keiner besonderen Wartung oder Schmierung der beweglichen Teile.
Trotzdem sollten jeweils nach einem Betrieb von sechs Monaten folgende Arbeiten
durchgeführt werden:
. das Gerät vom Netz abschalten.
. Die Komponenten innen im Gerät säubern.
. Sicherstellen, daß sich die Kohlenkontakte frei auf ihren Sitz bewegen können, daß
kein ungleichmäßiger Verschließ oder Überschläge aufgetreten sind.
Bei festgestellten Funkenspuren wie folgt vorgehen:
. die Kontaktbahnen des Stelltransformators mit einem Tuch säubern, ohne Lösungs-
mittel zu benutzen.
. Kohlenkontakte auswechseln.
N. fasi 3 +N
Tensione d'ingresso [V] 400
Variazione tensione d'ingresso [%] ±15
Potenza [kVA] 15
Massima corrente ingresso [A] 26
Corrente nominale [A] 22
Tempo di risposta [ms/Volt] 16
Tensione di uscita (stabil. vero valore efficace) [V] 400
Precisione di stabilizzazione [%] ±1
Frequenza [Hz] 50/60 ±5%
Variazione possibile del carico [%] da 0 a 100
Fattore di potenza del carico qualsiasi
Distorsione armonica [%] <0,2
Rendimento [%] 97 circa
Raffreddamento naturale in aria
Temperatura ambiente [°C] -10 +40
Temperatura di stoccaggio [°C] -20 +60
Umidità relativa (senza condensa) [%] 90
Grado di protezione IP 21
Peso [kg] 117
Dimensioni [mm] 535 x 410 x 1105h
MAN01646Y/2
19
Schema a blocchi e principio di funzionamento
MAN01646Y/2
20
Installazione ed uso
Tre fusibili (25A) proteggono la linea di uscita contro possibili corto circuiti.
Collegare la linea di ingresso ai morsetti di ingresso (U1 V1 W1 N1) (10) per mezzo di
cavi opportunamente dimensionati per la massima corrente di ingresso (26A).
Collegare la linea di uscita ai morsetti di uscita (U2 V2 W2 N2) (13) mediante fili di
sezione appropriata per la massima corrente erogabile in uscita (22A).
Collegare tramite un cavo unipolare di opportuna sezione il morsetto PE (12) alla terra
dell'impianto (vedi normative CEI EN 60439-1 e IEC 439-1).
MAN01646Y/2
21
Installazione ed uso
400/230V 3PH+N
400V 3PH
Dare tensione allo stabilizzatore e verificare sul voltmetro (2) il valore della tensione
stabilizzata tra due fasi. Tramite il commutatore (3) è possibile leggere le altre tensioni
concatenate sia in uscita che in ingresso.
Attenzione !
In caso di installazione dello stabilizzatore in presenza di:
. carichi con elevate correnti di spunto (es. pompe, compressori, grossi
motori...)
. carichi con elevati numeri di avviamenti (ascensori...)
. carichi generanti disturbi alta frequenza
. reti alimentate da gruppi elettrogeni
potrebbero generarsi condizioni critiche di funzionamento, qualora non sia
stato correttamente valutato il modello e il dimensionamento dello stabiliz-
zatore.
MAN01646Y/2
22
Disposizione componenti
1) Pannello strumenti
2) Voltmetro
3) Commutatore voltmetro
4) Lampada spia
5) Autotrasformatore variabile
6) Servomotore
7) Spazzola
9) Trasformatore serie
10) Morsettiera ingresso
11) Morsettiera uscita
12) Morsetto di terra
15) Scheda di controllo
16) Trimmer sensibilità
17) Trimmer azzeramento
18) Trasformatore alimentazione controllo
63) Fusibile uscita
MAN01646Y/2
23
Ricerca guasti
3. L’unità monofase lavora solo alzando la tensione o solo abbassandola (cioè lavora
in un solo senso):
- controllare che i microinterruttori S1-S2 lavorino correttamente.
- sostituire la scheda di controllo (15).
MAN01646Y/2
24
Ricerca guasti
5. L’unità monofase, a vuoto, si comporta nel seguente modo: con una tensione in
ingresso tra fase e neutro di poco superiore alla tensione di fase, la spazzola (7)
dell’autotrasformatore variabile si porta immediatamente a fine corsa in un senso.
Con una tensione in ingresso di poco inferiore alla tensione di fase, la spazzola (7)
dell’autotrasformatore variabile si porta immediatamente a fine corsa nel senso
opposto. La tensione in uscita invece rimane uguale a quella presente in ingresso:
- controllare che la presa ricavata sull’avvolgimento del variatore (5) non sia
dissaldata (a causa di un sovraccarico). In questo caso, prima di saldarla
nuovamente, verificare che l’autotrasformatore variabile (5) non presenti tracce
di surriscaldamento e bruciature, nel quale caso occorre sostituirlo.
- controllare che la spazzola dell’autotrasformatore variabile non sia consumata o
rotta e che non si riscontrino fiammeggiamenti nel punto di contatto tra la spazzola
e la pista.
- controllare che ci sia un buon contatto senza fiammeggiamenti tra i contatti
striscianti, connessione radiatore porta spazzole - morsettiera uscita autotrasfor-
matore variabile (5).
8. La tensione stabilizzata in uscita non rientra nel ±1% della tensione di fase, ma è più
alta o più bassa:
- riportare la tensione in uscita al valore corretto agendo sul trimmer (17) posto sulla
scheda di controllo (15).
MAN01646Y/2
25
Ricerca guasti
Manutenzione
MAN01646Y/2
27
Diagramme et principe de fonctionnement
MAN01646Y/2
28
Branchement et mise en service
Le régulateur doit être installé dans un milieu non poussiéreux et dans une position
permettant une libre circulation de l’air de refroidissement.
Trois fusibles, 25A de taille, protègent la sortie contre les possibles courts circuits.
La mise à la terre de l'appareil doit être effectuée à la borne marquée PE (12) moyennant
un câble unipolaire adapté aux caractéristiques de l'installation (voir normes EN 60439-
1 et IEC 439-1).
MAN01646Y/2
29
Branchement et mise en service
400/230V 3PH+N
400V 3PH
REGULATEUR
Attention !
Si l’installation du régulateur se produit en présence de:
. charges ayant des courants d’appel importants (ex. pompes, compresseurs,
moteurs...)
. charges ayant un grand nombre de démarrages (ascenseurs...)
. charges produisant bruits haute fréquence
. reseaux alimentés par des groupes électrogènes
lesdites conditions peuvent causer des malfonctionnements si modèle et
puissance du régulateur ne sont pas appropriés.
MAN01646Y/2
30
Plan des composants
1) Panneau de commande
2) Voltmètre
3) Sélecteur voltmètre
4) Lampe-témoin
5) Autotransformateur variable
6) Servomoteur
7) Balai
9) Transformateur série
10) Bornier d’entrée
11) Bornier de sortie
12) Borne de terre
15) Carte de contrôle
16) Réglage sensibilité
17) Retour à zéro
18) Transformateur d’alimentation
63) Fusible de sortie
MAN01646Y/2
31
Détection des pannes
Normalement les pannes se vérifient sur une unité monophasée seulement, toutefois
aussi les deux autres unités pourraient être endommagées. Il faut donc vérifier
soigneusement avant toute réparation.
La liste suivante se réfère aux pannes les plus probables et donne des renseignements
pour les résoudre. Naturellement elle se réfère à une unité monophasée seulement.
Les numéros se rapportent aux schémas d’encombrements et d’emplacement du
régulateur et du circuit de contrôle, de même qu’au schéma.
MAN01646Y/2
32
Détection des pannes
5. A vide et en présence d’une tension d’entrée légèrement plus élevée que la tension
de phase le balai (7) de l’autotransformateur variable se porte à fin de course dans
un sens; si la tension d’entrée se trouve plus basse que la tension de phase le balai
se déplace immédiatement dans le sens opposé. La tension à la sortie se trouve à
la même valeur que celle d’entrée:
- vérifier que la prise de l’autotransformateur variable ne soit dessoudée par
surcharge. Avant de la souder à nouveau contrôler le bon fonctionnement de
l’autotransformateur. S’il y a des composants en panne, remplacer
l’autotransformateur;
- contrôler l’efficacité des balais et qu’il n’ait pas de flambées entre le contact du
balais et la piste du transformateur;
- contrôler l’efficacité des contacts parmi les balais, la connexion de la base des
balais et le bornier de sortie de l’autotransformateur variable(5).
8. La tension de sortie ne se trouve pas à ±1% de la tension de phase, mais plus basse
ou plus haute:
- ramener la tension de sortie à la valeur correcte en appuyant sur le potentiomètre
(17) (retour à zéro) de la carte de contrôle (15);
MAN01646Y/2
33
Détection des pannes
Entretien
Le régulateur ne nécessite d’aucun entretien particulier ou de graissage des éléments
en mouvement.
Toutefois, tous les six mois, il est conseillé de procéder de la façon suivante:
- débrancher l’unité,
- nettoyer les composants intérieurs et effectuer un contrôle visuel,
- contrôler que les balais tournent librement et que les pistes de contacts ne
présentent pas de signes de brûlures ou de surchauffe. Si on observe des anomalies,
voir au point 9 de la détection des pannes.
MAN01646Y/2
34