Professional Documents
Culture Documents
With reference to below email, please find enclosed approved revised offer with amount of euro 1,520,000/= instead of
euro 1,510,000/= in order to proceed further.
Regards,
Hasan Kausar
Approved
Regards
Rizwan Younus
Dear Sir,
Please approve the enclosed revised offer with amount of euro 1,520,000/=.
Regards,
Hasan Kausar
1
________________________________________________________________________________
Your ref.:
______________________________
YUNUS TEXTILE MILLS LIMITED
Your inquiry: H-23/1,LANDHI INDUSTRIAL AREA,
Your order: KARACHI
______________________________ PAKISTAN
Concerning:
______________________________
_____________________________
Time of delivery:
st
1 partial shipment: ex works 14.02.2019
nd
2 partial shipment: ex works 27.02.2019
- provided we receive correct L/C before 14.09.2018
- provided we receive clarification of all
technical data at order release 10.09.2018
FYI
Please find attached the revised Order Confirmation & Proforma Invoice #: 31009315 dated: 14-Sep-18 for your
reference.
Also please send back your signed/stamped copy of both O/C & P/I at your earliest convenience.
Ali Zafar
_____
1
Muhammad Saqib
Regards,
Hasan Kausar
Approved
Regards
Rizwan Younus
Dear Sir,
Please approve the enclosed revised offer with amount of euro 1,520,000/=.
Regards,
Hasan Kausar
1
Dear Ali,
Regards,
Rizwan Younus.
Saqib
Dear Bernd,
Noted.
Regards,
Rizwan Younus.
2
Dear Younus
Noted. But we have 2 pH controls. Since we do not supply E&H for this we require € 5000.—for each separately.
Please open LC with this additional amount.
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
Hi Bernd,
Thanks for your response, the only thing which is left now to replace pH dozing system from Prominent to E&H.
Regards,
Rizwan Younus.
3
Good afternoon
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
Hi Bernd,
Plz find my response in the last.
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
OK
OK
4
• What type of inverters are they, vector control or servo based?
I do not have such information
OK
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load
when overcoming inertia caused by fabric tension. There is no other system available in our control
system.
OK
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide
1 inductive dosing line with E&H flow meter and Von Rohr control valve
Pump may please be installed of EIDOS Germany if possible !! E&H Flow meter & Von Rohr control
valve are OK
Benninger is usin Prominent doing pumps, we do not have any business relationship with Eidos. We are unable
to fulfill this request.
Ans 7 says flow meter’s brand is E&H but you wrote above Burkert Germany. please re check & confirm
??
Dosing for peroxide with inductive system is E&H. Water dosing is Bürkert.
OK
OK
Regards,
Rizwan Younus.
5
Sent from my iPhone
As discussed just now, please find below a reply from Benninger in color "Red" for your reference.
Ali Zafar
To: ali.zafar@acmatex.com.pk
Subject: RE: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Dear Ali,
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
Benninger does not supply Lenze inverters. Our inverter is SIMENS SINAMICS
LENZE
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load when
overcoming inertia caused by fabric tension. There is no other system available in our control system.
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
6
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide 1
inductive dosing line with E&H flwo meter and Von Rohr control valve
See answer 7. Flow meters for water dosing are Bürkert Germany
Profibus
Magtrol, Switzerland
SMC, Japan
Regards,
Rizwan Younus.
After having serious discussions with our Principal yesterday, we have managed to get a final price of
EUR. 1,500,000/- based on the attached revised scope of supply.
To summarize quickly & avoid any misunderstandings, the following items have been removed from our
previous scope of supply (offer #: OF65150B) as these items were not required by you aymore:
• Cooling clinders
• Dyeing padder
• Center winder
• Additional fabric entry in front of washing zone
• Consecutively steamer was put in lowered position
• Heat exchanger
• Mahlo rest humidity control
7
Benninger has confirmed their earliest possible delivery date of Beginning March’2019 (provided they
receive your L/C in their bank latest by 14-Sep-18).
We request you kindly give us your confirmation for this order of Pad Steam Range to enable us to
proceed further.
Ali Zafar
<image001.jpg>
<image002.jpg>
Mobile: 0300-8278959
ali.zafar@acmatex.com.pk
www.acmatex.com.pk
Dear Ali,
Further to our telecon, please be noted current price difference is around 40% if you can cut it by
half and able to give price around 1.4m then I can talk to top management.
Secondly please share scope of the machine and delivery time line.
Regards,
Rizwan Younus.
8
upport@acmatex.com.pk; s.imran@acmatex.com.pk
Subject: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
As discussed during our meeting at your office today, please note our best possible discounted price for a Pad Steam range
(based on the attached revised drawing) works out EUR. 1,600,000/-.
We request you to kindly confirm our above quoted price OR give us your closest offer to enable us to proceed further &
finalize this deal.
Ali Zafar
<image003.jpg>
<image003.jpg>
<image003.jpg>
<image003.jpg>
9
Cc: "'Imran Cheema'" <imran.cheema@yunustextile.com>, <i.rehmani@acmatex.com.pk>,
<sales.support@acmatex.com.pk>, <s.imran@acmatex.com.pk>, <nisar@yunustextile.com>, "'Aamir Dhedhi'"
<aamirdhedhi@yunustextile.com>, "'Javed Zakaria'" <jzakaria@yunustextile.com>
Subject: RE: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
undefinedundefinedundefined
Dear Ali,
Regards,
Rizwan Younus.
Saqib
Dear Bernd,
Noted.
Regards,
Rizwan Younus.
2
Sent: Thursday, September 13, 2018 2:34 AM
To: Rizwan Younus <rizwanyounus@yunustextile.com>; ali.zafar@acmatex.com.pk
Cc: 'Imran Cheema' <imran.cheema@yunustextile.com>; imu646@gmail.com; i.rehmani@acmatex.com.pk;
sales.support@acmatex.com.pk; s.imran@acmatex.com.pk; nisar@yunustextile.com
Subject: AW: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Dear Younus
Noted. But we have 2 pH controls. Since we do not supply E&H for this we require € 5000.—for each separately. Please
open LC with this additional amount.
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
e-mail signature_EN
Hi Bernd,
Thanks for your response, the only thing which is left now to replace pH dozing system from Prominent to E&H.
Regards,
Rizwan Younus.
3
To: Rizwan Younus <rizwanyounus@yunustextile.com>; ali.zafar@acmatex.com.pk
Cc: Imran Cheema <imran.cheema@yunustextile.com>; imu646@gmail.com; i.rehmani@acmatex.com.pk;
sales.support@acmatex.com.pk; s.imran@acmatex.com.pk; nisar@yunustextile.com
Subject: AW: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Good afternoon
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
e-mail signature_EN
Hi Bernd,
Plz find my response in the last.
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
OK
4
Please confirm, Series & Model Sinamics Inverters ??
SIEMENS SINAMIC S120
OK
OK
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load when
overcoming inertia caused by fabric tension. There is no other system available in our control system.
OK
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide 1 inductive
dosing line with E&H flow meter and Von Rohr control valve Pump may please be installed of EIDOS Germany if possible
!! E&H Flow meter & Von Rohr control valve are OK
Benninger is usin Prominent doing pumps, we do not have any business relationship with Eidos. We are unable to fulfill
this request.
Ans 7 says flow meter’s brand is E&H but you wrote above Burkert Germany. please re check & confirm ??
Dosing for peroxide with inductive system is E&H. Water dosing is Bürkert.
OK
OK
Regards,
5
Rizwan Younus.
As discussed just now, please find below a reply from Benninger in color "Red" for your reference.
Ali Zafar
Subject: RE: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Dear Ali,
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
Benninger does not supply Lenze inverters. Our inverter is SIMENS SINAMICS
6
LENZE
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load when
overcoming inertia caused by fabric tension. There is no other system available in our control system.
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide 1 inductive
dosing line with E&H flwo meter and Von Rohr control valve
See answer 7. Flow meters for water dosing are Bürkert Germany
Profibus
Magtrol, Switzerland
SMC, Japan
Regards,
Rizwan Younus.
7
Dear Mr. Rizwan Younus,
After having serious discussions with our Principal yesterday, we have managed to get a final price of EUR. 1,500,000/-
based on the attached revised scope of supply.
To summarize quickly & avoid any misunderstandings, the following items have been removed from our previous scope
of supply (offer #: OF65150B) as these items were not required by you aymore:
* Cooling clinders
* Dyeing padder
* Center winder
* Additional fabric entry in front of washing zone
* Consecutively steamer was put in lowered position
* Heat exchanger
* Mahlo rest humidity control
Benninger has confirmed their earliest possible delivery date of Beginning March’2019 (provided they receive your L/C in
their bank latest by 14-Sep-18).
We request you kindly give us your confirmation for this order of Pad Steam Range to enable us to proceed further.
Ali Zafar
<image001.jpg>
<image002.jpg>
Mobile: 0300-8278959
<mailto:ali.zafar@acmatex.com.pk> ali.zafar@acmatex.com.pk
www.acmatex.com.pk
8
<mailto:sales.support@acmatex.com.pk> sales.support@acmatex.com.pk; <mailto:s.imran@acmatex.com.pk>
s.imran@acmatex.com.pk; 'Nisar Palla'
Subject: RE: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Dear Ali,
Further to our telecon, please be noted current price difference is around 40% if you can cut it by half and able to give
price around 1.4m then I can talk to top management.
Secondly please share scope of the machine and delivery time line.
Regards,
Rizwan Younus.
As discussed during our meeting at your office today, please note our best possible discounted price for a Pad Steam
range (based on the attached revised drawing) works out EUR. 1,600,000/-.
We request you to kindly confirm our above quoted price OR give us your closest offer to enable us to proceed further &
finalize this deal.
Ali Zafar
<image003.jpg>
<image003.jpg>
<image003.jpg>
9
<image003.jpg>
<image001.jpg>
<image002.jpg>
<image003.jpg>
<https://starlifter.secure-xp.net:443/interface/img/s.png>
<https://starlifter.secure-xp.net:443/interface/img/s.png>
<https://starlifter.secure-xp.net:443/interface/img/s.png>
<https://starlifter.secure-xp.net:443/interface/img/s.png>
<http://www.yunustextile.com/logo/YBG.jpg>
<http://www.yunustextile.com/logo/go_logo.jpg>
<http://www.yunustextile.com/logo/YBG.jpg>
<http://www.yunustextile.com/logo/go_logo.jpg>
10
Confirmation no. 31009315 page 2
Floor space: The layout plan will be sent to you after release for
manufacturing.
For goods sold with delivery terms DAP, FOB, CFR, CIF, CIP, CPT etc. the truck,
ship or aircraft, respectively the forwarder and/or the insurance company are chosen
by the seller at its sole discretion. These delivery terms are applied according to
the interpretation of "INCOTERMS" valid at time of signature of the contract or
order confirmation.
Our machines are designed considering the valid European machine guidelines.
The buyer shall inform the seller before placing the order of any additional safety
devices or modifications which are deemed necessary in accordance with the
regulations of local professional or trade associations, or similar organisations.
These will be supplied and charged to the buyer. The absence of any such
additional safety device shall not constitute a defect.
According to our “General Delivery Terms” for machinery and plants from
(October 2014) point 12 to point 12.6 a project is defined to be agreed to be
accepted by the time when it is used in production terms. Remaining open
topics and pending point are listed and are to be settled by the parties involved.
We thank you for your order and assure you that it will receive our best attention.
Yours faithfully,
Benninger AG
Through:
ACMATEX CORP. (PVT.) LTD.
10-J, Block 6, P.E.C.H.S.
Karachi - 75400
PAKISTAN
May we ask you to confirm your acceptance of our general delivery terms,
the technical execution and the terms of payment by returning to us a copy
of our confirmation duly countersigned by you.
Date:
Technical Data
Cooling water <= 15° C for In-line liquor cooling system and liquor
trough
Stainless steel according EN 10020 1.4404 (AISI 316L) and 1.4301 (AISI 304)
- +/- Plaiter
The usage of wash-, wetting agents and other auxiliaries containing or based
on Phosphoric Acid Ester chemistry is causing a damage of rubber elements
such as squeezer rollers, bowed rollers and other rubberized rollers or
rubberized system parts. The usage of those products on Benninger Ranges
is not recommended. Furthermore Benninger rejects any guarantee regarding
this on mentioned parts.
CONSUMPTION FIGURES
Process:
Water and Steam water in l/kg steam in kg/kg with heat recovery
Heat exchanger is not in scope of supply of Benninger. Customer has to provide heat exchanger and
connections to heat exchanger in order to achieve the above mentioned steam consumption figures.
consisting of:
- batch and trolley have to be placed parallel and horizontal to the range
- no unbalanced batches
- constant braking effect on the batch roller
- batch must be fixed to the ground
consisting of:
200 Liters of hydraulic oil for initial charge of the hydraulic tank
for roller control
1 automatic quick cleaning system of the machine and liquor feeding system,
consisting of:
- 1 cleaning water distributor with trap
- 4 spraying pipes to clean trough, rollers and drain sheets
- 1 rinsing device for the liquor feeding system, by integration
of an additional valve block
1 safety sliding door at the machine inlet, sliding elements made of plexiglass,
with safety limit switch
1 safety sliding door at the machine outlet, sliding elements made of plexiglass,
with safety limit switch
ratio 4 : 1, constant (2000 + 500 l/h), for dosing of dyestuff and alkali-mix
for CPB dyeing process
consisting of:
consisting of:
Additional equipment
- 1 roller cleaning device consisting of:
connecting pipe for water feed with connecting flange and distributing pipe
with spray nozzles, 1 ball valve
- operation of roller cleaning device electropneumatic controlled with pneumatic
on/off valve
- roof heating consisting of indirect steam heating with distributing battery
incl. connection flanges and steam trap, 1 temperature probe pt100
1. temperature-control circuit:
saturated steam supply for working pressure of 4.5 bar overpressure at
max. 160°C, with pressure indication, dirt deflector and pneumatic regulating
valve, temperature probe for regulation of steam quantity into the steamer,
temperature probe for announcement on control terminal, manual flap valve
for steam distribution down / above into the steamer
2. water-control circuit:
soft water supply for feeding with 2 - 3 bar pressure, water tank, level control
with 3 measuring points, pneumatic on/off valve
consisting of:
- 1 trough made of stainless steel sheet, with hinged cover and windows,
with trough subdivisions, with outlets for serpentine counter flow
- all trough guide rollers with stainless steel cover and bearings with
life-time lubrication
- 3 separate drives for upper guide rollers with geared motors
- 1 compensating roller with pneumatic system to cloth tight strand
- 1 pneumatic drain-valve
- footboard at front side of the compartment
- guide bars in the compartment for crease-free cloth guiding
- additional rollers in the compartment for extension of the cloth tight
strand of 2 m
- all immersion trough guide rollers with bush bearings instead
of slide ring bearings
- 1 load-cell mounted on trough guide roller
- pneumatic control of pressure for compensating roller with pressure
regulating valve and manometer
- 1 scroll roller made of stainless steel tube, driven by separate motor
- 1 connecting box made of stainless steel sheet with hinged cover
- 1 pneumatic intermediate squeezer for a max. pressure of 30 kN with automatic
roller lifting
- 1 pressure roller with synthetic cover, 1 drive roller with stainless steel cover,
1 geared motor
- 1 bowed soft rubber covered expanding roller after the squeezer
- direct steam heating, consisting of: perforated pipes with injector incl. distributing
battery, 1 automatic temperature control with 1 software temperature controller,
1 temperature probe, 1 pneumatic valve with open/close function
- trough overflow with liquor flow alternatively into drain or into heat exchanger,
valve pneumatic controlled
Water feeding for range
- 1 automatic water feeding for 2 kinds of water, each unit consisting of:
1 connection pipe incl. 1 flow meter, control range 27 - 430 lt/min,
1 pneumatic regulating valve and 2 pneumatic valves
consisting of:
- 1 trough made of stainless steel sheet, with hinged cover and windows,
with trough subdivisions, with outlets for serpentine counter flow
- all trough guide rollers with stainless steel cover and bearings with
life-time lubrication
- 2 separate drives for upper guide rollers with geared motors
- 1 compensating roller with pneumatic system to cloth tight strand
- 1 pneumatic drain-valve
- footboard at front side of the compartment
- guide bars in the compartment for crease-free cloth guiding
- all immersion trough guide rollers with bush bearings instead
of slide ring bearings
- trough-inlet with waterlock
- 1 load-cell mounted on trough guide roller
- pneumatic control of pressure for compensating roller with pressure
regulating valve and manometer
- 1 scroll roller made of stainless steel tube, driven by separate motor
- 1 pneumatic intermediate squeezer for a max. pressure of 30 kN with automatic
roller lifting
- 1 pressure roller with synthetic cover, 1 drive roller with stainless steel cover,
1 geared motor
- direct steam heating, consisting of: perforated pipes with injector incl. distributing
battery, 1 automatic temperature control with 1 software temperature controller,
1 temperature probe, 1 pneumatic valve with open/close function
- trough overflow with liquor flow alternatively into drain, into heat exchanger
or into counterflow, valve pneumatic controlled
- 1 water feeding for trough filling with pneumatic valve, manually operated
- 1 electrical dosing pump, max. flow capacity 30 lt/h with connection pipe
- 1 vessel 140 lt content to dosing pump, made of PE
- 1 floating switch to vessel PE
- 1 centrifugal pump including piping and liquor distributing pipe
to connection at washing compartment
- 1 pH measuring transmitter with LCD indication and pH probe with
measuring cable (Endress & Hauser)
consisting of:
- 1 trough made of stainless steel sheet, with hinged cover and windows,
with trough subdivisions, with outlets for serpentine counter flow
- all trough guide rollers with stainless steel cover and bearings with
life-time lubrication
- 2 separate drives for upper guide rollers with geared motors
- 1 compensating roller with pneumatic system to cloth tight strand
- 1 pneumatic drain-valve
- footboard at front side of the compartment
- guide bars in the compartment for crease-free cloth guiding
- all immersion trough guide rollers with bush bearings instead
of slide ring bearings
- trough-outlet with waterlock
- 1 bowed soft rubber covered expanding roller at trough inlet
- 1 load-cell mounted on trough guide roller
- pneumatic control of pressure for compensating roller with pressure
regulating valve and manometer
- 1 scroll roller made of stainless steel tube, driven by separate motor
- 1 connecting box made of stainless steel sheet with hinged cover
- 1 pneumatic intermediate squeezer for a max. pressure of 30 kN with automatic
roller lifting
- 1 pressure roller with synthetic cover, 1 drive roller with stainless steel cover,
1 geared motor
- 1 bowed soft rubber covered expanding roller after the squeezer
- direct steam heating, consisting of: perforated pipes with injector incl. distributing
battery, 1 automatic temperature control with 1 software temperature controller,
1 temperature probe, 1 pneumatic valve with open/close function
- trough overflow into counter flow
consisting of:
- 1 automatic water feeding for 2 kinds of water, each unit consisting of:
1 connection pipe incl. 1 flow meter, control range 27 - 430 lt/min,
1 pneumatic regulating valve and 2 pneumatic valves
consisting of:
- 2 electrical dosing pump, max. flow capacity 30 lt/h with connection pipe
- 2 vessel 140 lt content to dosing pump, made of PE
- 2 floating switch to vessel PE
consisting of:
consisting of:
- 1 trough made of stainless steel sheet, with hinged cover and windows,
with trough subdivisions, with outlets for serpentine counter flow
- all trough guide rollers with stainless steel cover and bearings with
life-time lubrication
- 2 separate drives for upper guide rollers with geared motors
- 1 pneumatic drain-valve
- footboard at front side of the compartment
- guide bars in the compartment for crease-free cloth guiding
- all immersion trough guide rollers with bush bearings instead
of slide ring bearings
- trough-inlet with waterlock
- trough-outlet with waterlock
- 1 bowed soft rubber covered expanding roller at trough inlet
- 1 load-cell mounted on trough guide roller
- 1 scroll roller made of stainless steel tube, driven by separate motor
- 1 connecting box made of stainless steel sheet with hinged cover
- 1 pneumatic intermediate squeezer for a max. pressure of 30 kN with automatic
roller lifting
- 1 pressure roller with synthetic cover, 1 drive roller with stainless steel cover,
1 geared motor
- 1 bowed soft rubber covered expanding roller after the squeezer
- direct steam heating, consisting of: perforated pipes with injector incl. distributing
battery, 1 automatic temperature control with 1 software temperature controller,
1 temperature probe, 1 pneumatic valve with open/close function
- trough overflow into counter flow
consisting of:
- 1 trough made of stainless steel sheet, with hinged cover and windows,
with trough subdivisions, with outlets for serpentine counter flow
- all trough guide rollers with stainless steel cover and bearings with
life-time lubrication
- 2 separate drives for upper guide rollers with geared motors
- 1 compensating roller with pneumatic system to cloth tight strand
- 1 pneumatic drain-valve
- footboard at front side of the compartment
- guide bars in the compartment for crease-free cloth guiding
- all immersion trough guide rollers with bush bearings instead
of slide ring bearings
- trough-outlet with waterlock
- 1 pneumatically loaded EXTRACTA-roller with synthetic cover
- 1 load-cell mounted on trough guide roller
- pneumatic control of pressure for compensating roller with pressure
regulating valve and manometer
- direct steam heating, consisting of: perforated pipes with injector incl. distributing
battery, 1 automatic temperature control with 1 software temperature controller,
1 temperature probe, 1 pneumatic valve with open/close function
- trough overflow into drain
Chemical dosing installation for range
- 1 electrical dosing pump, max. flow capacity 17 lt/h with connection pipe
- 1 vessel 140 lt content to dosing pump, made of PE
- 1 floating switch to vessel PE
- 1 centrifugal pump including piping and liquor distributing pipe
to connection at washing compartment
- 1 pH measuring transmitter with LCD indication and pH probe with
measuring cable (Endress & Hauser)
consisting of:
consisting of:
15) 1 cloth delivery with cloth accumulator for batch change without
machine stop, with batching device for max. batch diameter of
2000 mm and plaiter
consisting of:
16) Multi-motor drive with digital drive control and process management
consisting of:
- 1 switch board with integrated cooling system, protection standard IP54, colour grey
Consumption management
- with indication of meter production
- with indication of electrical energy consumption
- with indication of water consumption
- with indication of steam consumption
- with indication of chemical consumption
Software controllers for load cells, for cloth tension measuring and regulation
of driving motors
Required emergency stop push button stations for installation along the range
Control for controlling reaction time on the roller bed or on plaiting device
Complete with hardware equipment and software package for the diagnosis and
assistance from our customer service-station direct to the customers range
connection via internet connection.
(customer has to provide network wiring to the switchboard and two public-IP
addresses for PLC and HMI, which are accessible for Benninger via internet e.g.
through VPN - Virtual Private Network)
Customer can access to the data via each OPC client software based
on OPC specification versions 1.x and 2.05. and the standards:
OPC DA 1.x, OPC DA 2.0 - 2.05, DDE, FastDDE, AdvancedDDE, CF-Text.
Benninger supply:
- Gateway from PLC to Ethernet network
- OPC Server software (to be installed on customer office PC)
- Linkage of the data from PLC to OPC Server
- Test of installation and availability of the data at the OPC Server
interface with OPC Test client
Customer supply:
- Office PC (with Windows 2000, XP)
- OPC Client Software
- Network installation (CAT5 cable, switch etc.) to Ethernet switch
inside the Benninger switch board
alongside the range and between motors and switch board including
metal conduct glands to main motors
(The maximum cable length between the switch board and the connection
points at the range must not exceed 50 m.
The location of the switch board has to be considered accordingly.)
- 1 BENNINGER technician, total 640 working, travelling and waiting hours for
Installing, mechanical commissioning, training and support during start-up period
Remarks:
Please request our technician 4 weeks before the intended start of the installation work.
The buyer is obliged to put enough helpers at the disposal of our erection personnel,
so that the erection can be executed within the stipulated time. See enclosed "General
Conditions of Erection".
In case of waiting hours which are not caused by default of BENNINGER, the resulting
excess time will be charged to the buyer at the actual rate.
Technical documentation
Dear Ali,
Regards,
Rizwan Younus.
Saqib 绰͛
Dear Bernd,
Noted.
Regards,
Rizwan Younus.
2
sales.support@acmatex.com.pk; s.imran@acmatex.com.pk; nisar@yunustextile.com
Subject: AW: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
Dear Younus
Noted. But we have 2 pH controls. Since we do not supply E&H for this we require € 5000.—for each separately.
Please open LC with this additional amount.
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
Hi Bernd,
Thanks for your response, the only thing which is left now to replace pH dozing system from Prominent to E&H.
Regards,
Rizwan Younus.
Good afternoon
Bernd Plankenhorn
Benninger AG
Fabrikstrasse
Hi Bernd,
Plz find my response in the last.
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
OK
4
Please confirm, Series & Model Sinamics Inverters ??
SIEMENS SINAMIC S120
OK
OK
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load
when overcoming inertia caused by fabric tension. There is no other system available in our control
system.
OK
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide
1 inductive dosing line with E&H flow meter and Von Rohr control valve
Pump may please be installed of EIDOS Germany if possible !! E&H Flow meter & Von Rohr control
valve are OK
Benninger is usin Prominent doing pumps, we do not have any business relationship with Eidos. We are unable
to fulfill this request.
Ans 7 says flow meter’s brand is E&H but you wrote above Burkert Germany. please re check & confirm
??
Dosing for peroxide with inductive system is E&H. Water dosing is Bürkert.
OK
5
OK
Regards,
Rizwan Younus.
As discussed just now, please find below a reply from Benninger in color "Red" for your reference.
Ali Zafar
To: ali.zafar@acmatex.com.pk
Subject: RE: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
㼀̬
Dear Ali,
• Since in the scope PLC mentioned as S7, what are the details like 1500 or1200?
SIEMENS S7-300
Benninger does not supply Lenze inverters. Our inverter is SIMENS SINAMICS
LENZE
• Scroller roll mentioned soft starter, our recommendation is to please install VFD.
Soft starter is included as an extra to start on/off motors of scroll rollers smoothly to avoid excessive load when
overcoming inertia caused by fabric tension. There is no other system available in our control system.
6
• There is no details referring with pH motor and sensor, our recommendation is to install E&H system.
pH system is by Prominent
• Similarly not details mentioned with dozing system, our recommendation is to install EIDOS.
Benninger uses own dosing system with Prominent pumps for dosing into counterflows and for peroxide 1
inductive dosing line with E&H flwo meter and Von Rohr control valve
See answer 7. Flow meters for water dosing are Bürkert Germany
Profibus
Magtrol, Switzerland
SMC, Japan
Regards,
㼀̬
Rizwan Younus.
After having serious discussions with our Principal yesterday, we have managed to get a final price of
EUR. 1,500,000/- based on the attached revised scope of supply.
To summarize quickly & avoid any misunderstandings, the following items have been removed from our
previous scope of supply (offer #: OF65150B) as these items were not required by you aymore:
• Cooling clinders
• Dyeing padder
• Center winder
• Additional fabric entry in front of washing zone
• Consecutively steamer was put in lowered position
• Heat exchanger
7
• Mahlo rest humidity control
Benninger has confirmed their earliest possible delivery date of Beginning March’2019 (provided they
receive your L/C in their bank latest by 14-Sep-18).
We request you kindly give us your confirmation for this order of Pad Steam Range to enable us to
proceed further.
Ali Zafar
<image001.jpg>
<image002.jpg>
Mobile: 0300-8278959
ali.zafar@acmatex.com.pk
www.acmatex.com.pk
Dear Ali,
Further to our telecon, please be noted current price difference is around 40% if you can cut it by
half and able to give price around 1.4m then I can talk to top management.
Secondly please share scope of the machine and delivery time line.
Regards,
Rizwan Younus.
8
From: Ali Zafar <ali.zafar@acmatex.com.pk>
Sent: Monday, August 27, 2018 2:15 PM
To:rizwanyounus@yunustextile.com
Cc:imran.cheema@yunustextiles.com; imu646@gmail.com; i.rehmani@acmatex.com.pk; sales.s
upport@acmatex.com.pk; s.imran@acmatex.com.pk
Subject: YUNUS TEXTILES - Discounted Price for a Pad Steam Range
As discussed during our meeting at your office today, please note our best possible discounted price for a Pad Steam range
(based on the attached revised drawing) works out EUR. 1,600,000/-.
We request you to kindly confirm our above quoted price OR give us your closest offer to enable us to proceed further &
finalize this deal.
Ali Zafar
<image003.jpg>
<image003.jpg>
<image003.jpg>
<image003.jpg>
9
<image001.jpg>
<image002.jpg>
<image003.jpg>
10
11
Right-click
here to
download
pictures. To
help protect
y our priv acy ,
Outlo ok
prev ented
auto matic
download of
this pictu re
from the
In ternet.
Right-click
here to
download
pictures. To
help protect
y our priv acy ,
Outlo ok
prev ented
auto matic
download of
this pictu re
from the
In ternet.
Right-click
here to
download
pictures. To
help protect
y our priv acy ,
Outlo ok
prev ented
auto matic
download of
this pictu re
from the
In ternet.
Right-click
here to
download
pictures. To
help protect
y our priv acy ,
Outlo ok
prev ented
auto matic
download of
this pictu re
from the
In ternet.
12