Professional Documents
Culture Documents
Prepared By:
Waltek Services (Shenzhen) Co., Ltd.
1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District,
Shenzhen 518105, China
Tel :+86-755-27553488
Fax:+86-755-27553868
* The sample detailed above has been tested to the requirements of Council Directives 2004/108/EC. The
test results have been reviewed against the Directives above and found to meet their essential
requirements.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:2 of 42
1 Test Summary
Test Test Requirement Test Method Class / Severity Result
Mains Terminal Disturbance EN55013:2001+A2:2 EN55013:2001+A2:20
Class B PASS
Voltage, 150kHz to 30MHz 006 06
Disturbance Power, EN55013:2001+A2:2 EN55013:2001+A2:20
Class B PASS
30MHz to 300MHz 006 06
Disturbance Voltage at the EN55013:2001+A2:2 EN55013:2001+A2:20
Class B N/A
Antenna Terminals 006 06
Radiation Emission, 30MHz EN55013:2001+A2:2 EN55013:2001+A2:20
Class B N/A
to 1000MHz 006 06
Harmonic Emission on AC, Clause 7 of EN61000-
EN 61000-3-2 : 2006 EN 61000-3-2 : 2006 N/A
100Hz to 2kHz 3-2
Clause 5 of EN61000-
Flicker Emission on AC EN 61000-3-3 :2008 EN 61000-3-3 :2008 PASS
3-3
EN61000-4-2 :1995 ±4 kV Contact
ESD EN55020:2007 PASS
+ A2:2001 ±8 kV Air
Electrical Fast Transients AC±1.0kV
EN55020:2007 EN61000-4-4 :2004 PASS
on AC
Remark:
A.M. Amplitude Modulation.
P.M. Pulse Modulation.
† D.M. – Differential Mode
* UT is the nominal supply voltage
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:3 of 42
2 Contents
Page
1 COVER PAGE ......................................................................................................................................................... 1
2 CONTENTS............................................................................................................................................................. 3
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page: 5 of 42
3 General Information
3.1 Client Information
Applicant: Cherub Technology Company Limited
Address of Applicant: Unit D, 8/F, Nanshan Bldg, No.15 Industry Rd. shekou
Shenzhen 518067 China
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:6 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:7 of 42
• IC – Registration No.:7760A
Waltek Services(Shenzhen) Co., Ltd. has been registered and fully described in a report filed
with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our
files. Registration No.:7760A, July 24, 2008.
The test items Antenna Terminal Disturbance Voltage ,S1,S2a,S2b,S3,S4,S5 were performed
at:-
Solid Industrial (Shenzhen) Co., Ltd. at 333 Bulong Highway Buji Longgang, Shenzhen,
Guangdong, China.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:8 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:9 of 42
Ipod 5K85004U
MP3 Player Aug-08 Aug-09 ±1dB
Player/A1285 3R0
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:11 of 42
Operating Environment:
Temperature: 25.5°C
Humidity: 51 % RH
Atmospheric Pressure: 1012 mbar
EUT Operation :
The EUT was placed on the test table working in INPUT mode,CD/MP3 mode and LINE
IN mode, the worst case mode was tested in CD/MP3 mode,and playing with 1KHz signal.
so the data were shown as follow.
The maximised peak emissions from the EUT was scanned and measured for both the Live
and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions
were within 6dB of the average limit line.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:12 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:13 of 42
Neutral Line:
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:14 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:15 of 42
Operating Environment:
Temperature: 25.5 °C
Humidity: 52 % RH
Barometric Pressure: 1012 mbar
EUT Operation:
The EUT was placed on the test table working in INPUT mode,CD/MP3 mode and LINE
IN mode, the worst case mode was tested in CD/MP3 mode,and playing with 1KHz signal.
so the data were shown as follow.
If any maximised peak emissions are detected within 15dB of the average limit line, then:
• Extend the lead to at least 6.2m (i.e. half wavelength at 30MHz plus twice the length
of the absorbing clamp) length or keep the original lead length (if no other lead can
is connected to the unit at the end of the lead).
• Maximise all peak emissions by moving clamp along cable.
• Perform Quasi-Peak and Average measurements on all maximised peak emissions
within 6dB of the average limit line.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:16 of 42
EARPHONE line
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:17 of 42
LINE IN line
INPUT line
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:18 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:19 of 42
“For the following categories of equipment limits are not specified in this edition of the
standard.
Note 1: Equipment with a rated power of 75W or less, other than lighting equipment.”
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:20 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:21 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:22 of 42
6.2 ESD
Test Requirement: EN 55020
Test Method: EN 61000-4-2
Test Result: PASS
Discharge Impedance: 330 Ω / 150 pF
Discharge Voltage: Air Discharge: +/-8 kV
Contact Discharge: +/-4 kV
HCP & VCP: +/-4 kV
Polarity: Positive & Negative
Number of Discharge: Minimum 10 times at each test point
Discharge Mode: Single Discharge
Discharge Period: 1 second minimum
Operating Environment:
Temperature : 24.0 °C
Humidity : 52 % RH
Barometric Pressure : 1012 mbar
EUT Operation:
The EUT was placed on the test table in working mode and playing with 1KHz signal.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:23 of 42
Results
A: No degradation in the performance of the E.U.T. was observed.
N/A: Not applicable.
Results:
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:24 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:25 of 42
Results:
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:26 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:27 of 42
Frequency Level
MHz dB(μV) (e.m.f.)
0.15 to 1.6 80-90 a
1.6 to 20 90-120 a
20 to 100 120
b
100 to 150 120-110
a
Increasing linearly with the logarithm of the frequency
b
Decreasing linearly with the logarithm of the frequency
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:28 of 42
Operating Environment:
Temperature : 23.0 °C
Humidity : 52 % RH
Barometric Pressure : 1012 mbar
EUT Operation:
The EUT was placed on the test table in working mode.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:29 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:30 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:31 of 42
6.5 S3 Measurement
Test Requirement: EN 55020
Test Method: EN 55020
Test Result: PASS
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:32 of 42
Operating Environment:
Temperature : 23.0 °C
Humidity : 52% RH
Barometric Pressure : 1012 mbar
EUT Operation:
The EUT was placed on the test table in working mode,and the worse terminal were recorded.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:33 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:34 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:35 of 42
Operating Environment:
Temperature : 24.0 °C
Humidity : 52 % RH
Barometric Pressure : 1012 mbar
EUT Operation:
The EUT was placed on the test table in working mode.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:36 of 42
Modulation Modulation
Comments:
A: No degradation in the performance of the E.U.T. was observed.
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:37 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:38 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:39 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:40 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:41 of 42
WALTEK SERVICES
Reference No.: WT09051209-E-E-E
Page:42 of 42
8 CE Label
1. The CE conformity marking must consist of the initials‘CE’taking the following form:
If the CE marking is reduced or enlarged, the proportions given in the above graduated
drawing must be respected.
2. The CE marking must have a height of at least 5 mm except where this is not possible on
account of the nature of the apparatus.
3. The CE marking must be affixed to the product or to its data plate. Additionally it must be
affixed to the packaging, if any, and to the accompanying documents.
4. The CE marking must be affixed visibly, legibly and indelibly.
It must have the same height as the initials‘CE’
WALTEK SERVICES
Reference No.: WT09051209-E-E-E