Professional Documents
Culture Documents
Contents
Chapter 1 Brief Introduction ......................................................................................... 1
1.1 Introduction ...................................................................................................... 1
1.2 G9 Mainframe ................................................................................................... 1
1.2.1 Front side of the mainframe ................................................................... 2
1.2.2 Control panel........................................................................................... 2
1.2.3 The bottom of G9 .................................................................................... 3
Chapter 2 Basic Operation of G9................................................................................... 4
2.1 Change work mode and datalink ...................................................................... 4
2.1.1 Change work mode ................................................................................. 4
2.1.2 Change datalink.............................................................................................. 5
2.2 Configure Base Station ...................................................................................... 7
2.3 Configure Rover Station .................................................................................... 8
2.3 Antenna Height measuring (Base and Static) ................................................... 9
2.4 Self Checking ..................................................................................................... 9
Chapter 3 Standard Accessories ................................................................................. 10
3.1 Base Standard Accessories .............................................................................. 10
3.2 External Radio Standard Accessories .............................................................. 10
3.3 Rover standard accessories ............................................................................. 11
3.4 Controller Standard Accessories ..................................................................... 11
Chapter 4 Assistant Software ...................................................................................... 12
4.1 Connect to Assistant Software ........................................................................ 12
4.2 Information ..................................................................................................... 13
4.3 Setting ............................................................................................................. 13
4.3.1 Change work mode ............................................................................... 14
(c) Rover Mode............................................................................................... 19
4.3.2 Change Data link ................................................................................... 20
4.3 Export Data ..................................................................................................... 24
4.4 Serial Port Forwarding..................................................................................... 26
4.5 Register ........................................................................................................... 27
4.5.1 Register via Controller ........................................................................... 27
4.5.2 Register via Assistant Software ............................................................. 27
4.6 Firmware Update ............................................................................................ 28
Appendix 1 Default Radio configuration .................................................................... 30
Appendix 2 Specification ............................................................................................. 30
G9
1.1 Introduction
1.2 G9 Mainframe
1
G9
1. Satellite led
2. Internal radio led
3. GSM/GPRS led
4. Bluetooth led
5. Power led
6. Rover led
7. Static led
8. Base led
9. Record led
2
G9
Base Station: UHF signal is transmit
Blink green
Rover Station: UHF signal is receiving
Blink red Signal strength is low.
Green Network datalink is selected
GPRS Indicator Blink green Net signals is receiving
Blink red Signal strength is low.
green A connection via Bluetooth is available.
Bluetooth Indicator
blue A Bluetooth connection has established.
green Power is on.
Power Indicator
red Power is low(<20%).
3
G9
No matter what brand of RTK you use, they all have 3 work mode base, rover and
static. When you select a work mode, it still has different datalink should selected. But
how to change the work mode and datalink?
For G9, there are 3 ways to change the work mode, via controller software, via PC
software and change directly. Depends on the controller software you use, the way to
change work mode is different, it depends on what’s software you use, SurvCE,
FieldGenius or others. How to use the PC software to change work mode? We have an
assistant software. We will introduce it in next chapter.
Here it will introduce how to change the work mode directly via control panel.
(1) Base mode
Press power button and function button at the same time until all of the led flash
at the same time. Then press Function to change the work mode, when the Base
indicator is on, press Power key to confirm base station.
4
G9
(2) Rover Mode
Press power button and function button at the same time until all of the led flash
at the same time. Then press Function to change the work mode, when the Rover
indicator is on, press Power key to confirm Rover station.
After confirm the work mode, next step is change data link. It’s also like modifying
work mode, you also can change the datalink via Control software, via PC assistant
software and change via control panel directly. Here we still just introduce how to
change datalink via control panel directly.
(1) Internal radio
After you confirming the work mode, then keep press Function button for about
5
G9
6 seconds until the datalink indicator blink. Then press Function(Not keep pressing) to
change datalink. When the UHF indicator is green, then press power button to
configure UHF datalink.
Base mode and rover mode all can configure with internal radio datalink. When
the indicator blinks, if receiver is base mode, it means transmit radio signals, if receiver
is rover mode, it means receive radio signals.
Base station shall be set up in the broad view, unobscured and higher places, avoid
the vicinity of the high voltage power transmission equipment and the transmitting
and receiving antennas of radio communication equipment, the shade of trees, and
the sides of water, all of which will produce different degrees of impact on the GPS
signal reception and emission of radio signals.
The steps for the installation of base are shown in the following pictures and
sheets.
7
G9
Step Description
Measure the height of the receiver. The detailed information please refer to "II.5 How
5
to measure the antenna height"
7 Set base parameters via controller and software. Then start base station
The steps for the installation of rover are shown in the following pictures and
sheets.
Step Description
1 Fix the bracket on the pole
2 Put the controller into the bracket and lock it
3 Screw the rover on the pole and attach receiving antenna into the port
4 Power on the receiver and select the rover working mode.
5 Open the controller and start the software, then configure the receiver
8
G9
When you use the receiver as static mode, there is a very important parameter
should be configured---Antenna Height, this is also very important for base station.
Antenna height is actually the vertical height of the phase center to ground
measurement point. But there are differences between different measure methods.
You can measure from the ground to the up of the mainframe rubber ring, in this
situation, you should select “Slant height to the measuring line”. In the standard
configuration, it has an altimetry piece, so you also can measure from the ground
(known point) to altimetry piece. In this situation you should select “Height to
altimetry piece”.
If the indicators are abnormal or the receiver can’t work normally, for example the
Bluetooth can’t be connected, the radio mode can’t work, it can’t connect to the CORS.
Then you can use the self-check function, to detective the receiver. It will check
internal radio module, GPRS module and Bluetooth module. If the self-checking can’t
pass, then the indicator will be red. For example, when you do the self-check, GPRS
and Bluetooth indicators are green, but the radio indicator is red. It means internal
radio module has question.
Self-check step as follow. Power on the receiver first. Then keep press power key,
the receiver will power off, but don’t release, just keep. The receiver will power on
again, then it start to do self-check. You can release the button.
9
G9
10
G9
1 Carry Case
2 Batteries
11
G9
In the standard accessories, it has a 4 pin USB cable. Use this cable connect G9 receiver to
your PC, then open Assistant software.
Click the Connection Icon which is in the top left corner. Then it will show Connect
interface, select the right COM port, then click OK.
12
G9
4.2 Information
After you click “OK”, wait for some seconds, then the receiver will connect to the
software. It will show “Information” directly.
The information contains “Device, Antenna, GPS, Radio, Network, Bluetooth and
work mode” In different part you can see detailed information. So when you want to
check detailed configuration, just look over this.
4.3 Setting
In this part you can change work mode and datalink, also NEMA output. This part
is very important, so we will introduce this part in detail.
13
G9
You can change work mode between static, base and rover here.
(a) Static Mode
In the software you can see “Static and Dynamic” under setting. Select “Static”
then you will see the static parameters.
You can input CutAngle, PDOP Threshold, PointName and Antenna Height. Of
course you also can select the Time Interval. You also can see “Automatic Record”. If
you select this, then when you power on the receiver and change the work mode to
Static, the receiver can record static data automatic. But after you save those
parameters, you should restart to apply.
In the bottom of the software, you can see “Satellite system” and “Save”. Click
“Satellites System”, it will show the opinion box. Usually we use “GPS, GLONASS and
BEIDOU” together. Click “Save” then all of these configurations will be applied.
14
G9
15
G9
After you select “Base” then you can see “Base Setting” in the left of Dynamic
Mode.
There are two start mode Start by unknown point or Start by known point.
(1) If you want to start the base on an unknown point. Then you should select
“Start by Single Position”. Within this choice, there are just 4 opinion parameters that
you can change. Input Site name, input delay time and input PDOP. There are
“Automatic Startup” selection, if you select it, then base station will transmit
automatic after powering on.
16
G9
(2) If you want to start base on known point. Then you should select “Start by
Specify Position” The 4 opinion parameters are same with “Start by Single Position”,
Site Name, Delay, PDOP and automatic startup.
But it also has little difference. Because this time we start base station on known
point, so we should input the coordinate of this point. Before you input, there are two
modes, Geodetic Coordinate BLH and Spatial Coordinate XYZ.
We introduce “Geodetic Coordinate BLH”, if you select this, then you should input
“Longitude, Latitude and Height”. It also has 3 different format to use----decimal
degrees, DD:MMSS, DD:MM:SS. Select according on your coordinate.
17
G9
But if you just has Spatial Coordinate, then you should input X, Y and Z. Select
“Spatial coordinate XYZ”, then input. After all of this, click OK.
That’s the configuration of “Base Setting”. Beside those, it still have 3 parameters
you can configure directly. It shows in follow picture.
Differential Type: The differential signal type that the base transmits. It contains DGPS,
18
G9
CMR, CMR PLUS, RTCM2, RTCM3, SCMRX and RTCM32. The default choice is RTCM32,
because RTCM32 contains BeiDou signal.
Elevation: Input as you want
Record Raw Data: If you select this, when the base station transmits differential signals,
at the same time, it also record the static data.
Time Interval: After you selecting “Record Raw Data”, you can configure the time
interval for static data.
Please select “Dynamic” in “Working Mode” then you will see “Base” and “Rover”
in Dynamic Mode, select Rover then you can configure the basic parameters of Rover
station.
19
G9
Different from base station, Rover just has 3 parameters to configure. It shows as
follow picture.
Differential Type: It has this parameter here, but actually the different can’t effect
rover station. Because the different type of rover depends on CORS and Base station.
If the CORS and Base station send RTCM32 signal, then rover receive RTCM32, but if
they send RTCM3, then Rover receive RTCM3.
Elevation: Input as you want.
Record Raw Data: If you select this, when you use Rover collect point, it also
record static data at same time.
Time Interval: After you selecting “Record Raw Data”, you can configure the time
interval for static data.
There are 5 kinds of datalink totally, they are “UHF, External, Network, Bluetooth,
Network and External”. And as we know, static mode doesn’t have a datalink just base
mode and rover mode has datalink. Base station can use UHF, External, Network,
Network and External, totally 4 kinds of datalink. Rover station can use UHF, Network,
Bluetooth, External, also totally 4 kinds of datalink.
20
G9
(1) UHF Datalink
Base and Rover station all can use UHF, it means internal radio. After you selecting
UHF, it will has a “Setting” menu besides the datalink. Click “Setting”, then come to
configure UHF parameters.
In this interface, there are many parameters you can change. Usually, you just
need modify Radio Channel, Radio Frequency, and Protocol. Other parameters are
default. Our radio module has 8 channels, the default frequency is from 441 to 448,
default protocol is TrimTalk450s. After configuration, click “OK” to exit.
21
G9
external radio to receiver. There is also a “Setting” menu. Click it to set. But in External
datalink, it just has one parameter you should set-----The baud to the external radio.
Different external radio has different baud. The external radio from our company have
same baud----38400.
22
G9
(4) Bluetooth Datalink (Data Collector Internet)
This datalink just can be used in Rover station, it means use controller connect to
internet. When you select this, there is no parameters to set, just click save to apply.
23
G9
Export data is also a very important parts of RTK, usually we connect the receiver
to PC via USB cable, then we can copy data from receiver, just like copy data from flash
driver to PC. Gintec G9 also have this function. But there is still another way for G9----
Use this Assistant Software
Connect G9 to PC then open this software. When you click “Export Data” you will
see the interface. You can see all of the static data, File name, Antenna Height, Size,
Start time, End time and data type.
Sometimes we want to rename the data and also change some information. Then
before you download, please select the data you want to edit, click “Set File
24
G9
Information” to edit. Here you can rename the point and also input the antenna height,
also the measure mode.
This part is used very little. Because this part is used for debug. And this function
need a special cable. Use this function, we can connect to OEM module, UHF module
Bluetooth module and Network module, then use other software to configure.
26
G9
4.5 Register
There are two ways to register G9 receiver, via controller and via this Assistant
software.
Connect to G9 with our software E-Survey, then it will shows as follow, click
“About”. In next window, you can see “Register Instrument”, click it. The last step is
input the code, then finish register.
In “Register” interface, you can see the device number and the expired date. Input
the register code. At last click “Upload License key” to register
27
G9
Sometimes we will release new firmware to deal some known questions. Use
Assistant Software to update is convenient. Connect the receiver to the Assistant
Software, then click “Firmware Upgrade”.
28
G9
Click update, it will shows an interface which you can select firmware. After
selecting, click “Open”. After this please restart receiver to apply new firmware. You
can check the version in “Information” part which we had introduced.
29
G9
The frequency and protocol of Channel 8 can be modified via controller. So you
can change it easily. And the frequency range is from 410MHz to 470MHz, so you can
elect as you want.
Appendix 2 Specification
Satellite Tracking
GPS L1C/A, L2C, L2E, L5
BEIDOU B1, B2
GLONASS L1C/A, L1P, L2C/A, L2P
GLOVE-A L1 BOC, E5A, E5B, E5AltBOC1
GLOVE-B L1 CBOC, E5A, E5B, E5AltBOC1
SBAS WASS, EGNOS, MSAS
Channel 220
Positioning Accuracy
DGNSS Horizontal: ±0.25m+1ppm(RMS)
Vertical: ±0.5m+1ppm(RMS)
Static Horizontal: ±2.5mm+1ppm
Vertical: ±5mm+1ppm
RTK Horizontal: ±10mm+1ppm
Vertical: ±20mm+1ppm
RTK initialization time < 10s Initialization reliability>99.9%
30
G9
Wireless Communication
Radio Modem 1W/2W optional internal transmit/receive radio module
Radio Frequency 410MHZ-470MHZ
Network WCDMA network communication, support HSDPA+, GPRS, GSM
Bluetooth Bluetooth 2.0, Class 2
Differential Link Support internal network, radio, external input, Bluetooth
Data format CMR, CMR+, RTCM2.X, RTCM 3.X
Electrical
External power DC 9V-18V (With overvoltage protection)
Battery capacity Two 3400mAH rechargeable and removable Li-ion battery
Static mode: 16h
Work time UHF base model:10h
UHF rover model:12h
Network model: 10h
31