You are on page 1of 6

TM - 188.

1 C060-057-09

Coiled Tubing
Accelerator
Dual Action – Flow Thro
Rev.0 TM – 188.1 – Accelerator Dual Action Flow Thro

PCE COILED TUBING DUAL ACTION ACCELERATOR

INTRODUCTION

The PCE Coil Tubing Dual Action Accelerator is used in conjunction with the PCE Coil Tubing
Dual Action Hydraulic Jar, its purpose being to provide the necessary even push and pull and
acceleration for the Coil Tubing Dual Action Hydraulic Jar to operate efficiently. This is achieved
by storing upward or downward energy in the compression spring that will impart a predictable
upward or downward blow.

Full ‘pump through’ capability of the Accelerator is compatible with the PCE Coil Tubing
Hydraulic Jar.

DESIGN BENEFITS

• Full flow through bore

• Heavy duty construction

MAINTENANCE

The PCE Coiled Tubing Accelerator has been designed to give long and reliable service.
However, it is strongly recommended that the tool is stripped and thoroughly cleaned after use
to remove any deposits that may interfere with its operation.

Inspect all parts for wear and replace all seals, backups and any worn or damaged parts.

This is particularly important when the tool has been in a corrosive environment.

Prior to re-assembly lightly oil or grease all parts.

PCE – Tel: +44 0 1202 631817 - Fax: +44 0 1202 631708 - E-Mail: sales@pce.co.uk
Rev.0 TM – 188.1 – Accelerator Dual Action Flow Thro

DIS-ASSEMBLY

Warning

Under normal operating conditions the coil spring is compressed with a force of approx.
200 lbs.

1. Break-out Bottom Sub (8) from Lower Body (6)

2. Break-out Lower Body (6) from Body Upper (4)

3. Break-out Body Lower (4) from Spring Retainer (3)

4. Break-out Lower Mandrel (7) from Spring Mandrel (5). Warning this will release the force
in the Coil Spring (12) , which is under compression.

5. The Thrust Washers (9) and Coil Spring (12) can now be removed.

6. Remove the Grub Screw (11) and break-out the Top Sub (1) and Spring Mandrel (5) from
the Upper Mandrel (2)

ASSEMBLY Use assembly drawing B060-AS-18

1. Load all ‘O’ rings and backups as per Product Data Sheet and Assembly Drawing.

2. Feed Upper Mandrel (2) through Spring Retainer (3) and make-up to Top Sub (1) and
secure with Grub Screw (11).

3. Make-up Spring Mandrel (5) to Spring Retainer (2). Feed Thrust Washer (9) and Coil Spring
(12) over Spring Mandrel (5)

4. Make-up Body Lower (6) to Body Upper (4) by approx. 3 threads. Install Thrust Washer (9)
into Body Upper (4).

5. Feed Body Upper (4) over Coil Spring (12) and make-up, by approx 1 inch to Spring
Retainer (3).
Force will be required as the spring is being compressed.

6. Insert Lower Mandrel through Body Lower (6) and make-up to Spring Mandrel (5) as far as
possible by hand.

7. Back-off and remove Body Lower (6) from Body Upper (4)

8. Make-up Lower Mandrel (7) through Spring Mandrel (5) and Upper Mandrel (2) to Top Sub
(1).

9. Re-make Body Lower (6) to Body Upper (4)

10. Make-up Bottom Sub (8) to Body Lower (6)


PCE – Tel: +44 0 1202 631817 - Fax: +44 0 1202 631708 - E-Mail: sales@pce.co.uk
Rev.0 TM – 188.1 – Accelerator Dual Action Flow Thro

PRESSURE CONTROL ENGINEERING PRODUCT DATA SHEET


____________________________________________________________________________
| Prod No: C060-057-09 Rev:0 (02 Jul 01) Drg No: C060-AS-18 |
| ACCELERATOR- DUAL ACTION |
| FLOW THRO Size Ref: 2 1/8 |
|____________________________________________________________________________|
| Max O.D: 2 1/8 |Fish Neck: |Service: STD |
| Min I.D: 0.39 | Top Con: 1.5 AMMT B |________________|
| Length: 63 |Lower Con: 1.5 AMMT P | Weight: 19.0|
| Other: | Other: | (Kg) |
|__________________________|________________________________|________________|
| W.Press: |W.Tensile: 45000 PSI | Tech Manual |
| T.Press: 5000 PSI |Calc Tens: 60000 PSI | |
| |Other P/L: | |
|__________________________|________________________________|________________|
| Notes: SPRING MSS0-301 6" STROKE |
| |
| |
|____________________________________________________________________________|
____________________________________________________________________________
|Item| Qty| Part No Rev | Description | Spare |
|____|____|______________|______________________________________|____________|
| 1 | 1 |00-29588 0| TOP SUB | |
| 8 | 1 |00-29705 0| BOTTOM SUB | |
| 15 | 1 |HV03-038 | O-RING | KS |
|200 | 1 |C060-057-00 0| *MAIN ASSEMBLY PARTS | |
|____|____|______________|______________________________________|____________|
Recommended Spares: KS (General Spares Kit) KR (Other Recommended Spares)

PCE – Tel: +44 0 1202 631817 - Fax: +44 0 1202 631708 - E-Mail: sales@pce.co.uk
Rev.0 TM – 188.1 – Accelerator Dual Action Flow Thro

PRESSURE CONTROL ENGINEERING PRODUCT DATA SHEET


____________________________________________________________________________
| Prod No: C060-057-00 Rev:0 (02 Jul 01) Drg No: C060-AS-18 |
| *MAIN ASSEMBLY PARTS |
| ACCEL- DUAL ACTION FLOW THRO Size Ref: 2 1/8 |
|____________________________________________________________________________|
| Max O.D: 2 1/8 |Fish Neck: |Service: STD |
| Min I.D: 0.39 | Top Con: |________________|
| Length: 63 |Lower Con: | Weight: |
| Other: | Other: | (Kg) |
|__________________________|________________________________|________________|
| W.Press: |W.Tensile: 45000 PSI | Tech Manual |
| T.Press: 5000 PSI |Calc Tens: 60000 PSI | |
| |Other P/L: | |
|__________________________|________________________________|________________|
| Notes: SPRING MSS0-301 6" STROKE |
| |
| |
|____________________________________________________________________________|
____________________________________________________________________________
|Item| Qty| Part No Rev | Description | Spare |
|____|____|______________|______________________________________|____________|
| 2 | 1 |00-29699 0| UPPER MANDREL | |
| 3 | 1 |00-29700 0| SPRING RETAINER | |
| 4 | 1 |00-29701 0| BODY UPPER | |
| 5 | 1 |00-29702 0| SPRING MANDREL | |
| 6 | 1 |00-29703 0| BODY LOWER | |
| 7 | 1 |00-29704 0| LOWER MANDREL | |
| 9 | 2 |00-29594 A| THRUST WASHER | |
| 10 | 1 |HV04-012 | O-RING | KS |
| 11 | 1 |FSH7-035 | HEX SOCKET SET SCREW | KS |
| 12 | 1 |MSS0-301 A| COIL SPRING | |
| 13 | 1 |HV04-008 | O-RING | KS |
| 14 | 2 |BU04-008 | SEAL BACKUP RING | KS |
|____|____|______________|______________________________________|____________|
Recommended Spares: KS (General Spares Kit) KR (Other Recommended Spares)

PCE – Tel: +44 0 1202 631817 - Fax: +44 0 1202 631708 - E-Mail: sales@pce.co.uk
Rev.0 TM – 188.1 – Accelerator Dual Action Flow Thro

PCE – Tel: +44 0 1202 631817 - Fax: +44 0 1202 631708 - E-Mail: sales@pce.co.uk

You might also like