Professional Documents
Culture Documents
BIOLOGICAL TESTING
IIA. Antibiotics
IIA1. Tablet Erythromycin estolate USP 60% to 150%
Erythromycin stearate IP
IIA2. Injection Amikacin sulphate IP
Polymyxin B sulphate USP
Streptomycin sulphate IP
Gentamycin sulphate IP
IIA3. Cream Neomycin sulphate IP
IIA4. Antibiotic liquids / Sterility test IP, BP and USP Complies / Does not
Antibiotic solids comply
VIIIA Adhesives
VIIIA Paper adhesives Test for stability IS 2257 Growth Observed/
(Fungal resistance test) not observed
VIIIB. Wood & Wood Products
VIIIB1. Block Board Mycological test IS 1659 Growth Observed/
not observed
VIIIB2. Plywood Mycological test IS 1734 Growth Observed/
not observed
IX. TOXICOLOGY
XA. Accessories Pyrogen test in rabbits IP, BP, USP, JP ,EP 10 ml/ Kg B.wt. per animal
Undue Toxicity/ IP, BP, USP, JP ,EP 1.0 ml of extract of test
Abnormal toxicity in Mice item per animal
XB. Surgical Items Undue Toxicity/ Abnormal IP, BP, US FDA, JP, 1.0 ml of extract of test
Rubber Tubing toxicity in mice EP item per animal
Pyrogen
XC. Gloves Dermal Irritation test in ISO10993- 10 1”x1” patch (for gloves)
Surgical, rabbits Skin Sensitization
Examination (Buehler’s method) in
guinea pigs
XD. Surgical Items- Sterility test IP, IS 10150 Complies/ Does not
Surgical / comply
Surgical Devices/ Bio- burden Test BS EN 1174 (P-3) 1 cfu/per product
Surgical Bacterial Endotoxin Test IP and USP Pass / Does not Pass
Gloves/Surgical (Gel Clot Method)
Blades
XI Molecular Analysis (GMO Testing)
XIA Cotton seeds, Detection of GMO w.r.t. SRI/MOL/012 & Qualitative
Soyabean seeds, screening of SRI/MOL/013 (LOD 0.1%)
Rice, Maize, Millet, 35S promoter and tNOS (By real-time PCR
Sesame seeds , terminator Technique)
Wheat, Rape seed,
Groundnut,
Raw Cotton (Lint)
XIB Bakery & Quantitation of Gluten by SRI/MOL/026 1 mg/kg – 80 mg/kg
Confectionery ELISA
Products, Animal
Feed, Coffee,
Cocoa & by
products, Cearals,
Pulses & by
products
CHEMICAL TESTING
II AYUSH PRODUCTS
IIA Asava & Arishta Moisture / LOD AP, Unani & Siddha 0.1 % to 50 %
(Fermentated Total Ash 0.1 % to 80 %
liquid) Arka/ Thee- Volatile oil 1.0 % to 50 %
neer/ Distillates, Alcohol soluble extractive 0.1% to 80 %
Avachurnam yoga Water Soluble Extractive 0.1% to 100 %
(Dusting Powder), Ether Soluble 0.1 % to 80 %
Avaleha/Leham/Mo Extractive
dak/Ilagam (Conf- Determination of Foreign 0.01 to 50 %
ection/Semisolid), Matter
Pishti Bhasma Acid soluble extractives 0.1 % to 100 %
Sindura Purpum Acid insoluble extractives
Chewing Candy Alcohol soluble extractives
Churna Ghansatva
Alcohol insoluble extractives
Lepa Medicated
Heavy Metals
Wax/Cream Netra-
Hg 0.2mg/k to 100 mg/kg
binduSharbat
Grannules Tailas Cd 0.2mg/kg to 20 mg/kg
Ghritas Vati/Gutika) As 0.2mg/kg to 2 mg/kg
Pb 0.2mg/kg to 100 mg/kg
IIIA Ambient Air Dust fall Rate IS: 5182 (P-1) 10 mg/m2/day to 10000
mg/m2/day
Sulphur dioxide IS: 5182 (P-2) 5 µg/m3 to 1050 µg/m3
Suspended Particulate IS: 5182 (P-4) 5 µg/m3 to 2000 µg/m3
matter (SPM)
PM10 - Particulate matter 5182 (P-23) 5 µg/m3 to 1000 µg/m3
(≤10 µm)
PM2.5 - Particulate matter SRI/EPD/Air Lab/01 5 µg/m3 to 500 µg/m3
(≤ 2.5 µm)
Nitrogen oxides IS: 5182 (P-6) 5 µg/m3 to 740 µg/m3
Hydrogen sulphide IS: 5182 (P-7) 6 µg/m3 to 600 µg/m3
Carbon monoxide IS: 5182 (P-10) 0.02 µg/m3 to 100 mg/m3
Benzene IS: 5182 (P-11) 0.3 µg/m3 to 100 µg/m3
PAH’s- Benzo (a) Pyrene IS: 5182 (P-12) 0.1 ng/m3 to 2000 ng/m3
(BaP)
IV BUILDING MATERIALS
IVA Aggregates Alkali aggregate reactivity IS 2386 (P-7) 2 milli mohs/L to 200 milli
Chloride mohs/L
Sulphates ( Water soluble & BS EN 1744 (P-1) 0.01% to 5%
total)
VII FERTILIZERS
IX GASES
XA Organic Chemicals
XA1 Acetone Purity content IS:170 70% to 99.9%
Color IS: 8768 Qualitative
Relative density IS:82 0.5 to 2.0
Distillation range IS:1448 50°C to 60°C
Water IS:2362 0.01% to 10 %
Residue on evaporation IS:82 1 to 10 mg/100ml
Acidity IS:170 0.001 g/100ml to 0.01
g/100ml
Alkalinity IS:170 Qualitative
Permangate test
Alcoholic impurities
XA2 Plasticizer esters Color IS:9591 Qualitative
Relative density 0.5 to 2.0
Refractive index 1.3 to 1.7
Water content IS:9591 0.01% to 10 %
Ash 0.01% to 10%
Acidity (as phthalic acid) 0.001% to 10%
Oil absorption 10 to 20
Water soluble 0.1% to 1%
XC33 Copper sulphate Copper IS:261 1% to 30%
Matter insoluble in water 0.05% to 1%
Soluble (Fe& Al) 0.1% to 1%
pH 2 to 14
Chloride 0.01% to 1%
Arsenic 10 mg/kg to 25Mg/kg
Pb & Zn Qualitative
XC34 Ferrous sulphate Ferrous sulphate IS:262 0.01% to 99.99%
Free acid 0.05% to 2%
PH 2 to 14
Fe, Mn 0.01% to 1%
Chloride 0.0005% to 0.01%
Phosphate 0.001% to 1%
Lead IS:262 10 mg/kg to 100 mg/kg
Arsenic 1 mg/kg to 10 mg/kg
Cu,Zn Qualitative
Alkaline salts &Alkaline earth 0.1% to 1%
XC35 EDTA Purity IS:7220 0.01% to 99.99%
Sulphated ash 0.05% to 1%
Iron 0.002% to 0.01%
Heavy metal( Pb) 0.001% to 1%
Nitrilotri acetic acid 0.1% to 1%
XIA Ink (Fountain pen Total Solid IS:220 ; IS:13209 0.5 to 10 gm/100ml
inkFerro gallo Iron Content IS:220 0.1% to 10%
tannateStamp Ratio of ethyl acetate 1 to 5.0
Pad Ink ndelible extract to iron
Ink Sedimentation 1.0 g/ml to 5.0 g/ml
Corrosion IS:220,IS:1221 1% to 10%
Freedom from clogging Visual
Stability Visual
Glycerol (Glycerin Content) IS:393 5% to 65%
Performance IS:13209; IS:393 Visual
Development
Acidity
Description IS:393
Colour
XII LEATHER
XIII LUBRICANTS
XIVA Metallic Coatings Mass of Zinc coating IS:6745; IS 2633 IS: 5 g/m2 to 50 g/m2
6745 50 g/m2 to 200 g/m2
200 g/m2 to 400 g/m2
400 g/m2 to 2000 g/m2
Silver coating IS: 3203 0.1 microns to 25 microns
Gold coating IS:12114 IS:3266 0.5 microns to 5.0 microns
Copper /Silver coating IS:3438 0.1 microns to 10microns
Chromium/ IS:3203 0.1 microns to 20microns
Nickel coating
Phosphate Coating IS: 3618 1 g/m² to 20 g/m²
Mass of Tin coating IS 1327; ISO-8442- 0.1 g/m² to 50g/m2
1&ISO-8442-2
XIVB Plating Solutions
XIVB1 Silver Potassium Silver IS:6267 50% to 70%
cyanide
XIVB2 Gold Potassium Gold IS:5761 ( P-I&II) 50% to 70%
cyanide Silver 0.5% to 10%
Turbidity Qualitative
XIVB3 Zinc salt Zinc oxide IS:1880 10% to 50%
Cyanide 0.1% to 10%
Cyanide –insoluble 0.05% to 10%
XIVB4 Nickel salt pH IS:1809 2 to 14
Nickel 1% to 50%
Cobalt 0.1% to 5%
Copper 0.001% to 2%
Lead 0.001% to 2%
XVIIA Paints & Enamels Drying time, 27±2°C,65 RH) IS:101(P3Sc-1) 3 hours to 4 hours 11 hours
Enamels Surface Dry IS: 2932 to 12 hours 23 hours to 24
(Ext, Int) Hard Dry hours ( Semiquantative)
Epoxy Enamel Tack Free
Two Component Consistency (Viscosity) IS:101(P1Sc-5) 15 Sec to 300 Sec
Glossy Finish IS:101(P3Sc-4) Visual
Polyurethane Fineness of Grind IS:101(P3Sc-5) 5 microns to 50 microns
Full Gloss Enamel Gloss 60° IS:101(P4Sc-4) 1 to 100 1 to 90
&Primer Gloss 20°
Grey Fillers for Colour IS:5 Visual
Enamels for use Water Content IS:101(P2Sc-1) 0.5% to 10 %
over Primers Wet Opacity IS:101(P4Sc-1) 5 to 50 sqm/l in the 0.004
Plastic Emulsion IS: 2932(PART-1), Scale, 2.55 to 25 sqm/l in
XXIIA Waste Water Colour, Visual IS: 3025 (P-4) Qualitative / 5 to 500 HU
Odour IS: 3025 (P- 5) Qualitative
Total Dissolved Solids IS: 3025 (P-16) 1 mg/l to 25000 mg/l
pH IS: 3025 (P-11) 1 to 14
Nitrate Nitrogen IS: 3025 (P-34) 2 mg/l to 1000 mg/l
Nitrite IS: 3025 (P-34) 0.01 mg/l to 100 mg/l
Sulfide IS: 3025 (P-29) 0.05 mg/l to 1000 mg/l
APHA 4500-S
Silica (Total, Molybdate IS: 3025 (P-35) 0.05 mg/l to 1000 mg/l
reactive and Unreactive) IS: 3025 (P-2)
Fluoride APHA 4500 F, 0.1 mg/l to 1000 mg/l
IS: 3025 (P-60)
Chloride IS: 3025 (P-32) 1 mg/l to 10000 mg/l
Sulfates IS: 3025 (P-24) 1 mg/l to 10000 mg/l
Magnesium IS: 3025 (P-46) 1 mg/l to 10000 mg/l
IS: 3025 (P-2)
XXVIA Soaps and Moisture and volatile matter IS:286 0.1% to 20% w/w
Synthetic Matter insoluble in alcohol 0.1% to 20% w/w
Detergents Free caustic alkali 0.1% to 1% w/w
Matter insoluble in water 0.1% to 80% w/w
Total alkalinity 0.1% to 5% w/w
Rosin acids 0.1% to 50% w/w
Titre of fatty acids 25C to 75C
Chlorides 0.1% to 10% w/w
pH of aqueous solution 0.1 to 14
Starch Qualitative
Total phosphates 0.2% to 10% w/w
XXX WATER
XXXA Potable and Colour IS: 3025 (P-4) 5 to 500 Hazen Units
Domestic Water Odour IS:3025 (P-5) Qualitative
for drinking Taste IS:3025 (P-7) Qualitative
purpose Turbidity, NTU IS:3025 (P-10) 1 NTU to 1000,NTU
pH IS:3025 (P-11) 1 to 14
ELECTRICAL TESTING
MECHANICAL TESTING
AT LABORATORY
I. AUTOMOTIVE COMPONENTS
24. AAC/ CLC Blocks Compressive Strength IS 6441 (P-5) 1 N/mm2 to10 N/mm2
Drying Shrinkage IS 6441 (P-2) 0.01 % to 1 %
Dimensions IS 2185 (P-3) 80 mm to 800 mm
Block Density IS 6441 (P-1) 350 Kg/m3 to 1500 Kg/m3
IS 6598; 2185 (P-3);
IS 2185 (P-4)
1. Ferrous & Non- Macro structural ASTM E3; IS11371 Qualitative test
Ferrous Metallic Examination IS3600 (P-9) (10X , 20X)
Materials Micro structural ASTM E3 Qualitative test
Examination ASTM E-562 (50 X to 1000 X)
ASTM A 247
IS3600 (P-9)
IS7739 (P-1)
IS7739 (P-5)
IS7754
IS 8329 &
Metals handbook
Vol 7 8th edition
Estimation of grain size by ASTM E 112 Qualitative Test
microscopic method IS4748 / ISO 643 (GS No. 1 to 10)
1. Proof Pressure Test Hydraulic Pressure Test IS1239 (P-1&2) Qualitative Test
on Ferrous/ Non IS1536; IS8329 (0.01 Kg/cm2 to 100
Ferrous Pipes & IS3989; IS1978 Kg/cm2)
Fittings Valves IS1729; IS778
Bib Cock and Stop IS781; IS14846
Cock IS4270; IS3589
2. Ferrous & Non Capacity IS 10325; IS 10339 0.1 liter to 40 liter
Ferrous IS 1825; IS 9992
Milk Can & IS 9503
Container Air Pressure test IS 10325; IS 10339 Qualitative test
IS 1825 IS 9992 (0.001 kg/cm2 to1 kg/cm2)
IS 916; IS 2471
Drop test IS 1825 Qualitative test
IS 2471
Handle pull test IS 10325; IS 9992 Qualitative test
IS 916; IS 2471
3. Ferrous & Non Capacity IS 2347 1 Ltr. to 22 Ltr.
Ferrous Air Pressure Test Qualitative test
Domestic (0.001 kg/cm2 to 1.5
Pressure Cooker kg/cm2)
Proof Pressure Test Qualitative test
(0.001 kg/cm2 to
3.0kg/cm2)
Operating test for Pressure Qualitative test
Regulating Device (0.001 kg/cm2 to 1.5
kg/cm2)
1. Soil Testing Sub Grain Size Analysis IS 2720 (P-4) Upto 100 %
Grade Embakment Classification IS 1498 LL : 0 to 50%
PL : 0 to 50%
PI : 0 to 20%
Grain Size : Upto 100%
Free Swell Index IS 2720 (P-40) 1% to 500%
Attenberg’s Limit IS 2720 (P-5)
a) Liquid Limit 0 to 50%
b) Plastic Limit 0 to 50%
c) Plasticity index 0 to 20%
California Bearing Ratio IS 2720 (P-16) 2 % to 100%
Proctor Compaction Test IS 2720 (P-8)
OMC IS 2720 (P-7) 5% to 30%
MDD 1g/cc to 5g/cc
Shrinkage Limit IS 2720 (P-6) 0.1% to 20%
Permeability IS 2720 (P-17) 1x 10-2 cm/s to 1x 10-7
IS 2720 (P-36) cm/s
Specific Gravity IS 2720 (P-3) 1 to 3
Moisture Content IS 2720 (P-2) 0.1% to 30%
Direct Shear Strength IS 2720 (P-3) 0 kg/cm2 to 5 kg/ cm2
0 deg to 60 deg
MECHANICAL TESTING
AT SITE
1. Soil Testing (Field) Load bearing capacity IS1888 5 ton/ m2-50 ton/ m2
(LBC) / Plate load test
Field density test IS 2720 (P-29) 1 g/cc to 3 g/cc
(Core cuter method)
Dry density IS 2720 (P-28) 1 g/cc to 3 g/cc
(Sand replacement method)
Earth Resistivity IS 15736 1 OHM-M to
1000 OHM-M
II. ATMOSPHERIC POLLUTION
1. Noise
a. Measurement of DG Set Acoustic SRI/EPD/AIR 40 dB (A) to 120 dB (A)
Noise Emitted by Enclosures, Acoustically LAB/NV/02
Machine Treated DG Rooms & IS 4758
Machines Noise in dB (A)
b. Measurement of Environmental (Ambient) SRI/EPD/AIR 40 dB (A) to 120 dB (A)
Airborne Noise Level, Work Area LAB/NV/02;
Acoustical Noise and Indoor Noise Level in IS 9876
and Evaluation of dB (A)
its Effects on Man
c. Assessment of Environmental(Ambient)Noi SRI/EPD/AIR 40 dB (A) to 120 dB (A)
Noise with Respect se Level in dB (A) LAB/NV/02;
to Community IS 9989
Response
NON-DESTRUCTIVE TESTING
RADIOLOGICAL TESTING
II. WATER
1. Water Alpha Emitters IS 14194 (Part 2) Min, 0.1Bq/l
Beta Emitters IS 14194 (Part 1) Min. 1.0 Bq/l