Professional Documents
Culture Documents
Indian Standard
SPECIFtATION FOR RADIO
FREQUENCY CONNECTORS OF N-SERIES
PART 1 TEST SCHEDULE AND REQUIREMENTS
I
0 Copyright 1988
Gr 4 December 1988
I8 ! 12380( Part 1 )- 1988
hdiun Standard
SPECIFICATIONFOR RADIO
FREQUENCYCONNECTORSOFNSERlES
PART 1 TEST SCHEDULE AND REQUIREMENTS
0. FOREWORD
0.1 This Indian Standard ( Part 1 ) was adopted detail specifications for specific types of connec-
by the Bureau of Indian Standards on 25 April tors. I
1988, after the draft finalized by the Connectors
for Electronic Equipment Sectional Committee 0.4 While preparing this standard, assistance has
had been approved by the Electronics and Tele- been derived from JSS 52402‘Detail specification
communication Division Council. for connectors, radio frequency, series N’,
issued by the Directorate of Standardization,
0.2 This standard ( Part 1 ) is one of the series of Ministry of Defence, India.
Indian Standards on radio frequency connectors
for frequencies above 3 MHz, used in electronic 0.5 For the purpose of deciding whether a
equipment, and shall be read in conjunction with particular requirement of this standard is comp-
IS : 5054-1988”. lied with, the final value, observed or calculated,
expressing the result of a test shall be rounded
0.3 This standard ( Part 1 ) is the sectional Off in accordance with IS : 2-1960*. The
specification covering N series of connectors. number of significant places retained in the
Subsequent parts OF this standard would cover rounded off value should be the same as that of
the specified value in this standard.
*General requirements and methods of tests for radio
frequency connectors above 3 MHZ ( secondicitfsfaff ).
1
IS:12380(Part l)- 1988
22 = represents variants like materials, shall be as specified in the relevant detail speci-
finishes, cables, cable technique, fication.
applications, etc.
9. TESTS
4.3 The type designations shall be specified in the
relevant detail specification. 9.1 General - The test schedule specifies the
tests and the order in which they shall be carried
5. MARKING out as well as the requirements to be met.
5.1 The connectors shall be marked in accordance 9.2 Conditions of Tests - The provisions of 8
with 6 of IS : 5054-1988*. of IS : 5054-1988* shall apply.
6. PACKAGING 9.3 Classification of Tests - The provisions of 7
6.1 The connector shall be suitably packaged to of IS : 5054-1988* shall apply.
withstand normal handling and transit hazards.
9.4 Test Schedule
6.2 Packaging ( presentation, identification and
packaging ) shall be in accordance with the terms 9.4.1 Type Tests - The test schedule for type
of contract. - tests and the sequence of tests shall be as specified
in Table 1. The manufacturers shall submit 22
7. CLIMATIC CATEGORY mating pairs of each style for which approval is
desired. If approval is desired for all types
7.1 The climatic category shall generally be
covered in any particutar category, the manu-
according to 3 of IS : 5054-1988*.
facturer shall submit 5 mating pairs in each of the
remaining types of the particular category. The
8. ELECTRICAL CHARACTERISTICS
additional samples shall be subjected to Group 5
8.1 The electrical characteristics of connectors tests only.
*General requirements and methods of tests for radio *General requirements and methods of tests for radio
frequency connectors above 3 MHz ( second revision ) frequency connectors above 3 MHz ( second revision ).
*General requirements and methods of tests for radio frequency connectors above 3 MHz ( second revision ).
( Continued )
IS : 32380( Part 1) - 1988
3
IS r 12380( Part 1 )- 1988
5
IS : 12380 ( Part 1) - 1988
DETAIL X
DETAIL AT x
Nora - Three holes 0.69 mm minimum diameter equally spaced, are required for safety wiring after
mating. Location on coupling nut optional.
All dimensions in millimeters.
FIG. 1 MATING DIMENSIONS
FORMALE CONTACTS
SHAPE OF TIP
OPTIONAL O-25 max.
FLAT PERMITTED --I
OPlION*L
6
IS : 12380 (Part 1) - 1988
9.4.2 Routine Tests - The following tests shall b) Voltage proof ( duration 2 seconds, see
be carried out in the order stated: 10.6 of IS 5054&1988* ).
a) Visual examination ( see 9.1 of IS : 5054 9.4.3 Acceptance Tests - Two groups of
-1988* ), and samples ( Group A and Group B ) shall be selec-
ted, preferably at random from the lot that has
passed routine tests stated in 9.4.2 above. Each
*General requirements and methods of tests for radio group of connectors shall be subjected to the
frequency connectors above 3 MHz ( second revision ). tests in the order given in Table 2.
,
TABLE 2 SCHEDULE OF ACCEPTANCE TESTS
*General requirements and methods of tests for radio frequency connectors above 3 MHz ( second revision 1.
tsampling plans and procedures for inspection by attributes for electronic items.
$D - Destructive and ND - Non-destructive.
§Three samples shall be subjected to the test irrespective of lot size and one or more failures shall constitute
rejection of the lot.
.
7