Professional Documents
Culture Documents
/ the Item
N
Specifications:
Nominal capacity: 30 Nm
Maximum specimen length: 750 mm
Gearbox ratio: 60:1
Drive sockets: 3/16” Whitworth and 12 mm AF hexagonal (2 off each should be supplied)
Strain measurement: Electronic encoder and digital display
Torque measurement: Strain gauged load cell and digital display
Power Source: 220~230V AC, 50Hz, 1 Phase
0.1% carbon steel (six nos.) & 0.4% carbon steel specimens (six nos.) should be supplied
with the equipment
Should be supplied with mechanical torsiometer for use with 6 mm diameter specimens in
both the elastic and plastic regions
1
2 Transducer
. s, Devices Range
instrumenta Min Max
tion and
rotary and slider 80kΩ 120kΩ
Control
variable
Teaching
resistors(carbontrack
Set and wirewound)
IC temperature sensor. 2.92V 3.04V
Platinum RTD 99.9 ohm 100.1 ohm
resistance transducer
n.t.c. thermistor. 4230 ohm 5170 ohm
thermocouple(Type K) Ref. Voltage 2.92 V 3.04 V
photovoltaic cell. Open circuit voltage 500mv
Short Circuit Current 10 mA
phototransistor Dark Current ICO=100na for MEL 12
Light Current IL=6mA
For SFH 300-3
photoconductive cell Dark Resistance 10 M-ohm Cell Resistance 2.4 K-ohm
PIN photodiode Light Current 7nA/lux Dark Current=1 nA
Linear Variable Mechanical Travel=15 mm
Differential Turns per coil=75
Transformer (LVDT) Output voltage=10mV(1mm from
balance)
linear variable capacitor Capacitance=25 pF Mechanical Travel=15mm
Capacitance=50pF
strain gauge. Deflection=0.5 mm
Output Voltage=2.35 V
air flow transducer Output Voltage,-=2.1 V
Output Voltage,+=1.7 V
air pressure transducer Output Voltage,-=2.51 V
Output Voltage,+=2.48 V
humidity transducer Humidity Range=10% R-H Humidity Range=90% R-H
Output Voltage=340 mV.
Slotted Opto Output voltage=4.9 V(beam admitted)
Transducers
Reflective Opto Output Voltage= 3V(beam Output Voltage= 1.5V(beam broken)
Transducers reflected)
Inductive Transducers Output Voltage= 130 mV
Hall Effect Transducers 7.5mV/mT 10.6 mV/mT
Tacho-Generator Open ckt. o/p voltage=10.5 V,Short
ckt. o/p current=750 mA
2
converter (I/V)
voltage to frequency Full scale Frequency=10kHz
converter (V/F).
frequency to voltage Output Ripple=10mV
converter (F/V). Output Impedence=100k-Ohm
full wave rectifier. Output Voltage error=-6% 6%
a comparator Output voltage=-11.8 V 12 V
an alarm oscillator Output Frequency=540Hz
an electronic switch Trip Voltage=2.1 V,Output
Current=1A
40kHz oscillator. Center Frequency=38236 Hz 44442Hz
low pass filters -12V +12V
Analog Triggers
Number of triggers ..........................1
Source..............................................AI, ScopeCH0, ScopeCH1
Functions .........................................Start Trigger, Reference Trigger, Pause Trigger, Sample
Clock, Convert Clock, Sample Clock
3
PFI / Port 1 / Port 2 Functionality
Functionality ................................... Static digital input, static digital output, timing input,
timing output
Voltage Measurement
DC Ranges.......................................100 mV, 1 V, 10 V, 60 V AC
Ranges.......................................200 mVrms, 2 Vrms, 20 Vrms
Input frequency range
(AC voltage)....................................40 Hz to 20 kHz
Current Measurement
DC range...............2 A
AC ranges..............500 mArms, 2 Arms
Shunt resistance...............................0.1 Ω
Resistance Measurement Ranges............................................. 100 Ω, 1 kΩ, 10 kΩ, 100 kΩ, 1
MΩ, 100 MΩ
Capacitance Measurement
Range ............................. 50 pF to 500 μF
Accuracy........................... 1%
Test voltage..................................... 1 Vpk
Inductance Measurement
Range ........................ 100 μH to 100 mH
Accuracy ..................... 1%
Test voltage
100 μH to 1 mH.......................... 0.5 Vpk
1 mH to 10 mH........................... 0.5 Vpk
10 mH to 100 mH....................... 1 Vpk
Diode Measurement
Ranges .............................................1 V, 10 V
Nominal test current ........................1 mA (1 V range) 100 μA (10 V range)
Function Generator
Channels ..........................................1
Output waveform type.....................Sine, square, triangle
Modulation
Inputs...............................................2 (AM and FM)
Modulation input range ...................±10 V
Modulation factor
AM .....................10%/V
FM.................20%/V
Oscilloscope
Channels ..........................................2
Sampling mode....Scanned
Input coupling................................AC, DC
impedance................................1 MΩ || 25 pF
4
Bandwidth (–3 dB)................................1.7
Triggering
BNC TRIG Input Input
impedance.............................. 1 MΩ VIH
min ........................................... 2.4 V VIL
max ........................................... 400 mV