Professional Documents
Culture Documents
Installation Manual
Important
Please read this Installation Manual
carefully to familiarize yourself with
safe and effective usage.
Product CIDVI-AH
Version 3.0
Date 30Mar2012
Status Private
CIDVI-AH 1
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Table of Contents
1 DEFINITIONS AND ACRONYMS..................................................................................... 1
CIDVI-AH 2
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Version Tracking
CIDVI-AH 1
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Before starting any installation work , you must wait 90 seconds after turning the ignition switch
to the LOCK position and disconnecting the negative (-) terminal from the battery. When
disconnecting the battery, the saved addresses and radio stations of the navigation system will not
be deleted, just the settings of board computer (BC1 and BC2) will be lost.
ATTENTION:
After you reconnect the battery terminal please be very carefully to don’t make a short circuit
between power supply connector of the lamp inside of glove-box and RCA connectors of
interface. You can destroy the interface and the CID.
CIDVI-AH 2
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Farbe-Bild-Austastung-Synchron – german
FBAS
abbreviation for CVBS
Separate Video is an analog video signal that
carries video data as two separate signals: lumen
(luminance) and chroma (color). This differs from
S-VIDEO composite video, which carries picture information
as a single lower-quality signal, and component
video, which carries picture information as three
separate higher-quality signals.
Referred also as a Carputer - is a digital computer
CarPC
engineered for integration into an automobile
Display screen Refers to the CID LCD screen.
Touch panel Refers to the panel that fits over the display screen
and provides the touch functionality.
Refers to the combined product—the display screen
Touch screen
and the touch panel.
CIDVI-AH 1
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 2
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 3
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Note:
DON’T use both solutions in the same time. This two solutions suppose that your CarPC to have
available an S-Video / Composite connector. Otherwise, you need a VGA to S-Video/Composite
converter.
The user has the option to use the Video Input #1 for connection of front view camera (FVC).
CIDVI-AH 4
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 5
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 6
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Current screen Short Press Long Press (2s) Hold Press (>10s)
CID Select Video Input #1 Automatic Inputs Factory Reset
(CVBS/FBAS) Scanning
Video Input #1 Select Video Input #2 Change Composite N/A
(CVBS/FBAS) (S-VIDEO) Image Mode 1,2,3,4
Video Input #2 Select Video Input #3 Change S-Video Image N/A
(S-VIDEO) (CVBS/FBAS) Mode 1,2,3,4
Video Input #3 Select CID Screen Change Composite N/A
(CVBS/FBAS)) Image Mode 1,2,3,4
Video Input #4 RVC N/A Mirroring N/A
(CVBS/FBAS)
Note:
If the interface is not detecting any video signal related to the current screen, then the screen
will be switched to blue color for 5s, after that switching back to CID screen.
Note:
The Video Input #2 and Video Input #3 are not available in the same time. The user has to
decide to which video input will connect the video device.
CIDVI-AH 7
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
In addition of selecting the video input sources, the push button allows the following control
functions as well:
Change Image Mode – Mode 1 (default), Mode 2, Mode 3, Mode 4(user) – are
selected one by one by pressing the button longer than 2s while on the screen is
displaying one of the available video input sources. These modes provide preset
picture parameters. After Mode 4, the image mode will go back to Mode 1. The value
will be kept after ignition is turned off as well. The Mode 4(User) includes user-
defined picture parameters that can be changed through control port only
independently for composite and S-Video input sources (see section for more
information).
Automatic Inputs scanning – the interface detects, store and switches only the video
inputs that have a video device attached - press the button longer than 2s while on the
screen is displaying CID information. During the scanning procedure each screen is
shown for a short while (blue screen is shown if no signal). After detection, only the
screens related to valid video signal can be selected.
Enable Front View Camera – perform the automatic input scanning leaving the
Video Input #1 out of video signal. After that power and connect the front view
camera to Video Input #1. In this mode, the user has available only Video #2 or Video
#3 for other video devices. The push button doesn’t select the screen from Video
Input #1 related to front view camera.
Mirroring Video Input 4# RVC – press the button longer than 5s while the screen is
displaying the video signal from rear view camera. The image mode is the same as set
for the two video input sources. Repeat the procedure for returning to native camera
mode.
Factory Reset – press the button longer than 30s while on the screen is displaying
CID information. The reset is visible on the screen as an image flick.
CIDVI-AH 8
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 9
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 10
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Note:
The following work must be done with special care not to destroy the CID! You should
discharge yourself from electrostatic energy by touching e.g. the water pipe prior to open the
CID. Also you should not wear clothes that support charging with electrostatic energy like
wool pullovers etc.
After removing the rear shield plate of the CID you can see the CID-controller board and the
30-pole ribbon cable that connects the CID-TFT and CID-controller. It has to be spitted
(Figure 5 CID Controller Board View, red arrow).
CIDVI-AH 11
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Next step is to take out the CID-controller boards and CID-TFT. In order to do that you must
first unplug the power connector for the TFT-display (if present) and flip the controller board
by 180° to the top as shown in Figure 6 CID Flipped Controller View.
CIDVI-AH 12
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Because the new ribbon cable is too long, it must be folded as shown in Figure 7 Folded
Ribbon Cable View. It does not harm the ribbon cable if it is folded. The free end of the
ribbon cable should near to the top of plastic frame approx. 3-4 cm in vertical position.
CIDVI-AH 13
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 14
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 15
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 16
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
The ribbon cables must not cross themselves or be swapped by 180°! Both connectors do
have a locking slider that must be pushed out first before inserting a ribbon cable. When
CIDVI-AH 17
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
inserting the ribbon cables into the connectors, take care that they are not skewed and fully
inserted! Then push the slider back towards the connector to lock it.
The slider might not be locked properly in the middle, so it is recommended to push the
middle of the slider with a small screwdriver towards the connector to assure proper locking.
If this is done, put on the rear shielding plate carefully without moving the CID-Interface out
of its position (see pictures from Figure 12 Fitting CID Interface Board View). After that,
check if the ribbon cables are still locked into connectors.
Note:
These operations MUST BE performed very carefully because the female connectors can be
damage easy.
CIDVI-AH 18
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 20
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 21
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
In order to execute the first test run, you need to connect the car battery again. When opening
the driver’s door, the usual Opel-logo etc. should appear in the CID. Pay special attention to
the colors of the CID-display, they must not be strange or missing. Press and release shortly
the push button in order to switch the CID to display the 1st video input. Press again and select
the 2nd video input, and again to come back to the CID display.
If this test looks OK, the CID-Interface with its ribbon cables seems to be installed correctly
and the battery must be disconnected again to continue the installation.
If you do not see any picture on the CID LCD-TFT even after switching on the ignition or the
colors are not displayed correctly or the selected video input are not displayed, the CID has to
be removed again for rechecking. You have to remove the CID rear shield plate and reconnect
the cables just for testing purpose as indicated in Figure 15 Video and Control Cables. Please
refer to Chapter Troubleshooting
If the first test was successful and the battery was disconnected again, remove the interface
connectors from CID and go to installation and wiring of video devices and CIDVI-AH
interface.
CIDVI-AH 22
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 23
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Note:
For new Opel/Vauxhall cars, the power supply for backup light (including reversing light) is
like a pulsing voltage (using PWM) increasing the bulb life. It will affect the video signal from
rear view camera, mainly when the engine is running. The best option is to power the rear
view camera from a stable power supply (e.g cigarette), eventually through a relay powered
from reversing lamp. The ground for camera should be from the chassis mass.
CIDVI-AH 24
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Other option is to use an Insulation Transformer with filtering inductor and capacitor
between reversing light and camera power supply.
Note:
The front view camera is working only in relation to rear view camera. For testing, you need
to have rear view camera connected.
4.5.4 Telmute
The TELMUTE control signal should be wired to pin #11available on Head Unit connector as
indicate in Figure 19 Head Unit Pinouts.
CIDVI-AH 25
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Note:
For video devices that need ignition signal, the power supply wire could be connected to
pin#15 and ACC could be connected to pin#13 as indicated in Figure 19 Head Unit Pinouts.
After this is done and the video equipments and cables are connected as indicated in Figure 2
Wiring Diagram, the battery can be connected again to perform a proper functional test of the
CIDVI-AH kit.
CIDVI-AH 26
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
After that, select the second video input source. If there is not connected other video signal
then the same screen will be displayed. Press again and move to the CID information.
Turn the ignition ON, start the engine and change gear to reverse. Automatically, the screen
should display the rear view camera, if it’s available. After releasing the change gear, the
screen should display back the previous image.
Make a call from another phone to the mobile phone connected to the Opel car kit. When the
phone starts to ring, the screen should switch automatically to the CID screen and display the
caller name from the phone tab. It’s working only for Opel car kits connected to CID through
CAN.
If all these tests were successful, go and finish the installation of CID with console and EHU.
CIDVI-AH 27
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 28
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
Remove the protective tape on the rear side of touch panel. Clean very well the glass of CID
LCD-TFT.
Insert back the CID LCD over the touch panel as in figure below. Be carefully with the
rainbow cable indicated by blue arrow.
Next step is to continue with video interface board as is presented in Section 14.3 Installing
CID Interface Board.
CIDVI-AH 29
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
After the interface board was installed, you may connect the rainbow cable to the touch panel
as it’s indicated in the figure below.
Now, connect all the interface cables and close the CID as it’s presented in Section 4.3.
Next step is to connect the rainbow cable and USB cable to the 4 wires touch controller and
insert it into varnish tube. See the pictures below.
CIDVI-AH 30
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
CIDVI-AH 31
30Mar2012 Status Private Version 3.0
OPEL & VAUXHALL CID VIDEO INTERFACE ASTRA H / ZAFIRA B / CORSA D / ANTARA
6 Troubleshooting
If a problem still remains after applying the suggested remedies, contact us to
office@energys.ro
CIDVI-AH 32
30Mar2012 Status Private Version 3.0